The following information is also available:
Time column is TIME ORDERED-> Determining observation start and end
Offset of 148478001.431500 from 1993-01-01 00:00:00 is date and time (including leapseconds) = 1997-09-15 11:53:17.43149 Modified Julian Day = 50706.495340642359224-> leapsec.fits already present in current directory
Offset of 148596643.035600 from 1993-01-01 00:00:00 is date and time (including leapseconds) = 1997-09-16 20:50:39.03560 Modified Julian Day = 50707.868507356484770-> Observation begins 148478001.4315 1997-09-15 11:53:17
ATTITUDE_V0.9j
reading attitude file:./merged.tmp
open asc output file:out.tmp
AVERAGE ASPECT AND OFFSET FOR THIS ATTITUDE FILE:
Attitude file start and stop ascatime : 148478005.431400 148596643.035600
Data file start and stop ascatime : 148478005.431400 148596643.035600
Aspecting run start and stop ascatime : 148478005.431511 148596643.035489
Time interval averaged over (seconds) : 118637.603979
Total pointing and manuver time (sec) : 20394.476562 98243.195312
Mean boresight Euler angles : 267.529849 117.387333 172.369413
RA DEC SUN ANGLE
Mean solar position (deg) : 173.00 3.03
Mean aberration (arcsec) : 2.16 -1.44
Mean sat X-axis (deg) : 283.767586 61.648925 96.99
Mean sat Y-axis (deg) : 181.056389 6.771067 8.86
Mean sat Z-axis (deg) : 267.529849 -27.387332 95.42
RA DEC ROLL OFFSET
(deg) (deg) (deg) (arcmin)
Average 267.229034 -27.484879 82.231422 0.184430
Minimum 267.148865 -27.487003 82.222565 0.000000
Maximum 267.234711 -27.470867 82.307335 4.289220
Sigma (RMS) 0.001792 0.000161 0.002877 0.212842
Number of ASPECT records processed = 21347
Aspecting to RA/DEC : 267.22903442 -27.48487854
closing output file...
closing attitude file...
-> Standard Error Output From FTOOL attitudeATTITUDE_V0.9j : Detected gap > 15min in attitude file: 148479629.42616 ATTITUDE_V0.9j : Detected gap > 15min in attitude file: 148507737.33208 ATTITUDE_V0.9j : Detected gap > 15min in attitude file:-> Standard Output From STOOL checkatt:
Opening file: ./out.tmp
***************** Observation Info ******************
RA (J2000 deg): 267.229 DEC: -27.485
START TIME: SC 148478005.4315 = UT 1997-09-15 11:53:25
****** Definition of Attitude SENSOR Bit Flags ******
Sensors used in the attitude determination and attitude control mode
1: USED, 0: NOT USED
B0:STT-A, B1:STT-B, B2:NSAS, B3:GAS, B4:SSAS-SA, B5:SSAS-SB,
B6:IRU-X, B7:IRU-Y, B8:IRU-Z, B9:IRU-S1, B10:IRU-S2,
B11: Attitude control mode 1: coarse, 0: fine
B12: Sun presence 1: day, 0: night
B13: STT-A earth occultation 1: earth occultation, 0: no occultation
B14: STT-B earth occultation 1: earth occultation, 0: no occultation
B16,17,18: STT-A track stars no.1,2,3, 1: USED, 0: NOT USED
B19,20,21: STT-B track stars no.1,2,3, 1: USED, 0: NOT USED
B22,23: always 0
******** Attitude File Reconstruction Summary *******
S S N G S S I I I I I A S S S S S
T T S A S S R R R R R C U T T T T
T T A S A A U U U U U M N T T T T
- - S . A A - - - - - . . - - - -
A B . . - - X Y Z S S . . A B A B
. . . . S S . . . 1 2 . . O O S S
offset_time separation sensor . . . . A B . . . . . . . C C T T
(sec) (arcmin) . . . . . . . . . . . . . C C R R
BIT: 0 1 2 3 4 5 6 7 8 9 A B C D E
4.000129 3.942 8803 1 1 0 0 0 0 0 0 0 0 0 1 0 0 0 0 0
103.999710 2.917 FC88C3 1 1 0 0 0 0 1 1 0 0 0 1 0 0 0 4 7
251.999222 1.899 8803 1 1 0 0 0 0 0 0 0 0 0 1 0 0 0 0 0
363.998810 0.897 8803 1 1 0 0 0 0 0 0 0 0 0 1 0 0 0 0 0
1127.996338 0.358 FC80C3 1 1 0 0 0 0 1 1 0 0 0 0 0 0 0 4 7
4679.984375 0.392 FC88C3 1 1 0 0 0 0 1 1 0 0 0 1 0 0 0 4 7
6887.976562 0.045 FC80C3 1 1 0 0 0 0 1 1 0 0 0 0 0 0 0 4 7
10423.964844 0.060 8803 1 1 0 0 0 0 0 0 0 0 0 1 0 0 0 0 0
12647.957031 0.009 FC80C3 1 1 0 0 0 0 1 1 0 0 0 0 0 0 0 4 7
16167.945312 0.046 FC88C3 1 1 0 0 0 0 1 1 0 0 0 1 0 0 0 4 7
18407.937500 0.032 FC80C3 1 1 0 0 0 0 1 1 0 0 0 0 0 0 0 4 7
21927.925781 0.024 8803 1 1 0 0 0 0 0 0 0 0 0 1 0 0 0 0 0
24103.919922 0.019 FC80C3 1 1 0 0 0 0 1 1 0 0 0 0 0 0 0 4 7
27687.908203 0.028 8803 1 1 0 0 0 0 0 0 0 0 0 1 0 0 0 0 0
115979.609375 0.291 8003 1 1 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
118636.101562 3.619 9603 1 1 0 0 0 0 0 0 0 1 1 0 1 0 0 0 0
118637.601562 4.289 9603 1 1 0 0 0 0 0 0 0 1 1 0 1 0 0 0 0
Attitude Records: 21347
Attitude Steps: 17
Maneuver ACM time: 98243.2 sec
Pointed ACM time: 20394.5 sec
-> Calculating aspect point85 101 count=2 sum1=534.905 sum2=234.757 sum3=344.876 86 101 count=2 sum1=534.924 sum2=234.748 sum3=344.828 92 102 count=3054 sum1=817014 sum2=358494 sum3=526409 93 102 count=18187 sum1=4.8656e+06 sum2=2.13493e+06 sum3=3.1349e+06 94 101 count=14 sum1=3745.64 sum2=1643.36 sum3=2413.38 94 102 count=4 sum1=1070.16 sum2=469.536 sum3=689.517 95 101 count=14 sum1=3745.76 sum2=1643.33 sum3=2413.46 96 101 count=14 sum1=3745.89 sum2=1643.3 sum3=2413.57 97 101 count=24 sum1=6421.78 sum2=2817 sum3=4137.73 98 100 count=15 sum1=4013.76 sum2=1760.56 sum3=2586.15 98 101 count=3 sum1=802.738 sum2=352.119 sum3=517.224 99 100 count=11 sum1=2943.52 sum2=1291.03 sum3=1896.56 100 100 count=3 sum1=802.798 sum2=352.089 sum3=517.245 0 out of 21347 points outside bin structure-> Euler angles: 267.53, 117.388, 172.37
Interpolating 9 records in time interval 148596638.535 - 148596641.536 Interpolating 1 records in time interval 148596642.536 - 148596643.035
Dropping SF 26 with synch code word 1 = 147 not 243 Dropping SF 27 with inconsistent SIS mode 0/1 Dropping SF 50 with synch code word 0 = 226 not 250 Dropping SF 51 with synch code word 0 = 122 not 250 Dropping SF 195 with inconsistent datamode 0/2 Dropping SF 196 with inconsistent SIS mode 1/3 Dropping SF 197 with synch code word 2 = 34 not 32 639.998 second gap between superframes 1977 and 1978 Dropping SF 3969 with invalid bit rate 5 Dropping SF 3970 with invalid bit rate 6 Dropping SF 4303 with corrupted frame indicator Dropping SF 4305 with invalid bit rate 7 5350 of 5361 super frames processed-> Removing the following files with NEVENTS=0
ft970915_1153_2050G202170H.fits[0] ft970915_1153_2050G202270M.fits[0] ft970915_1153_2050G202370M.fits[0] ft970915_1153_2050G203970M.fits[0] ft970915_1153_2050G204070L.fits[0] ft970915_1153_2050G204170M.fits[0] ft970915_1153_2050G204270M.fits[0] ft970915_1153_2050G204370M.fits[0] ft970915_1153_2050G204470M.fits[0] ft970915_1153_2050G205470M.fits[0] ft970915_1153_2050G205570L.fits[0] ft970915_1153_2050G205670L.fits[0] ft970915_1153_2050G205770H.fits[0] ft970915_1153_2050G205870H.fits[0] ft970915_1153_2050G205970H.fits[0] ft970915_1153_2050G206070H.fits[0] ft970915_1153_2050G206170H.fits[0] ft970915_1153_2050G206870H.fits[0] ft970915_1153_2050G206970M.fits[0] ft970915_1153_2050G207070M.fits[0] ft970915_1153_2050G207170L.fits[0] ft970915_1153_2050G207270M.fits[0] ft970915_1153_2050G207370H.fits[0] ft970915_1153_2050G207470H.fits[0] ft970915_1153_2050G207570H.fits[0] ft970915_1153_2050G207670H.fits[0] ft970915_1153_2050G207770H.fits[0] ft970915_1153_2050G207870H.fits[0] ft970915_1153_2050G208470M.fits[0] ft970915_1153_2050G208570H.fits[0] ft970915_1153_2050G208670H.fits[0] ft970915_1153_2050G208770H.fits[0] ft970915_1153_2050G208870H.fits[0] ft970915_1153_2050G208970H.fits[0] ft970915_1153_2050G302170H.fits[0] ft970915_1153_2050G302270H.fits[0] ft970915_1153_2050G302370M.fits[0] ft970915_1153_2050G302470M.fits[0] ft970915_1153_2050G304070M.fits[0] ft970915_1153_2050G304170L.fits[0] ft970915_1153_2050G304270M.fits[0] ft970915_1153_2050G304370M.fits[0] ft970915_1153_2050G304470M.fits[0] ft970915_1153_2050G304570M.fits[0] ft970915_1153_2050G305570M.fits[0] ft970915_1153_2050G305670L.fits[0] ft970915_1153_2050G305770L.fits[0] ft970915_1153_2050G305870H.fits[0] ft970915_1153_2050G305970H.fits[0] ft970915_1153_2050G306070H.fits[0] ft970915_1153_2050G306170H.fits[0] ft970915_1153_2050G306970H.fits[0] ft970915_1153_2050G307070M.fits[0] ft970915_1153_2050G307170M.fits[0] ft970915_1153_2050G307270L.fits[0] ft970915_1153_2050G307370M.fits[0] ft970915_1153_2050G307470H.fits[0] ft970915_1153_2050G307570H.fits[0] ft970915_1153_2050G307670H.fits[0] ft970915_1153_2050G307770H.fits[0] ft970915_1153_2050G308570M.fits[0] ft970915_1153_2050G308670H.fits[0] ft970915_1153_2050G308770H.fits[0] ft970915_1153_2050G308870H.fits[0] ft970915_1153_2050G309070H.fits[0] ft970915_1153_2050S001901M.fits[0] ft970915_1153_2050S002701L.fits[0] ft970915_1153_2050S101901M.fits[0] ft970915_1153_2050S102701L.fits[0]-> Checking for empty GTI extensions
ft970915_1153_2050S000101M.fits[2] ft970915_1153_2050S000201L.fits[2] ft970915_1153_2050S000301M.fits[2] ft970915_1153_2050S000401H.fits[2] ft970915_1153_2050S000501M.fits[2] ft970915_1153_2050S000601H.fits[2] ft970915_1153_2050S000701L.fits[2] ft970915_1153_2050S000801M.fits[2] ft970915_1153_2050S000901H.fits[2] ft970915_1153_2050S001001M.fits[2] ft970915_1153_2050S001101H.fits[2] ft970915_1153_2050S001201L.fits[2] ft970915_1153_2050S001301H.fits[2] ft970915_1153_2050S001401M.fits[2] ft970915_1153_2050S001501L.fits[2] ft970915_1153_2050S001601M.fits[2] ft970915_1153_2050S001701L.fits[2] ft970915_1153_2050S001801M.fits[2] ft970915_1153_2050S002001L.fits[2] ft970915_1153_2050S002101L.fits[2] ft970915_1153_2050S002201H.fits[2] ft970915_1153_2050S002301L.fits[2] ft970915_1153_2050S002401H.fits[2] ft970915_1153_2050S002501M.fits[2] ft970915_1153_2050S002601M.fits[2] ft970915_1153_2050S002801M.fits[2] ft970915_1153_2050S002901H.fits[2] ft970915_1153_2050S003001M.fits[2] ft970915_1153_2050S003101H.fits[2]-> Merging GTIs from the following files:
ft970915_1153_2050S100101M.fits[2] ft970915_1153_2050S100201L.fits[2] ft970915_1153_2050S100301M.fits[2] ft970915_1153_2050S100401H.fits[2] ft970915_1153_2050S100501M.fits[2] ft970915_1153_2050S100601H.fits[2] ft970915_1153_2050S100701L.fits[2] ft970915_1153_2050S100801M.fits[2] ft970915_1153_2050S100901H.fits[2] ft970915_1153_2050S101001M.fits[2] ft970915_1153_2050S101101H.fits[2] ft970915_1153_2050S101201L.fits[2] ft970915_1153_2050S101301H.fits[2] ft970915_1153_2050S101401M.fits[2] ft970915_1153_2050S101501L.fits[2] ft970915_1153_2050S101601M.fits[2] ft970915_1153_2050S101701L.fits[2] ft970915_1153_2050S101801M.fits[2] ft970915_1153_2050S102001L.fits[2] ft970915_1153_2050S102101L.fits[2] ft970915_1153_2050S102201H.fits[2] ft970915_1153_2050S102301L.fits[2] ft970915_1153_2050S102401H.fits[2] ft970915_1153_2050S102501M.fits[2] ft970915_1153_2050S102601M.fits[2] ft970915_1153_2050S102801M.fits[2] ft970915_1153_2050S102901H.fits[2] ft970915_1153_2050S103001M.fits[2] ft970915_1153_2050S103101H.fits[2]-> Merging GTIs from the following files:
ft970915_1153_2050G200170M.fits[2] ft970915_1153_2050G200270L.fits[2] ft970915_1153_2050G200370M.fits[2] ft970915_1153_2050G200470H.fits[2] ft970915_1153_2050G200570H.fits[2] ft970915_1153_2050G200670H.fits[2] ft970915_1153_2050G200770H.fits[2] ft970915_1153_2050G200870M.fits[2] ft970915_1153_2050G200970M.fits[2] ft970915_1153_2050G201070H.fits[2] ft970915_1153_2050G201170H.fits[2] ft970915_1153_2050G201270H.fits[2] ft970915_1153_2050G201370H.fits[2] ft970915_1153_2050G201470L.fits[2] ft970915_1153_2050G201570L.fits[2] ft970915_1153_2050G201670M.fits[2] ft970915_1153_2050G201770H.fits[2] ft970915_1153_2050G201870H.fits[2] ft970915_1153_2050G201970H.fits[2] ft970915_1153_2050G202070H.fits[2] ft970915_1153_2050G202470M.fits[2] ft970915_1153_2050G202570M.fits[2] ft970915_1153_2050G202670H.fits[2] ft970915_1153_2050G202770H.fits[2] ft970915_1153_2050G202870H.fits[2] ft970915_1153_2050G202970H.fits[2] ft970915_1153_2050G203070L.fits[2] ft970915_1153_2050G203170L.fits[2] ft970915_1153_2050G203270H.fits[2] ft970915_1153_2050G203370H.fits[2] ft970915_1153_2050G203470H.fits[2] ft970915_1153_2050G203570H.fits[2] ft970915_1153_2050G203670M.fits[2] ft970915_1153_2050G203770M.fits[2] ft970915_1153_2050G203870M.fits[2] ft970915_1153_2050G204570M.fits[2] ft970915_1153_2050G204670M.fits[2] ft970915_1153_2050G204770L.fits[2] ft970915_1153_2050G204870L.fits[2] ft970915_1153_2050G204970M.fits[2] ft970915_1153_2050G205070M.fits[2] ft970915_1153_2050G205170M.fits[2] ft970915_1153_2050G205270M.fits[2] ft970915_1153_2050G205370M.fits[2] ft970915_1153_2050G206270H.fits[2] ft970915_1153_2050G206370H.fits[2] ft970915_1153_2050G206470H.fits[2] ft970915_1153_2050G206570L.fits[2] ft970915_1153_2050G206670H.fits[2] ft970915_1153_2050G206770H.fits[2] ft970915_1153_2050G207970H.fits[2] ft970915_1153_2050G208070H.fits[2] ft970915_1153_2050G208170M.fits[2] ft970915_1153_2050G208270M.fits[2] ft970915_1153_2050G208370M.fits[2]-> Merging GTIs from the following files:
ft970915_1153_2050G300170M.fits[2] ft970915_1153_2050G300270L.fits[2] ft970915_1153_2050G300370M.fits[2] ft970915_1153_2050G300470H.fits[2] ft970915_1153_2050G300570H.fits[2] ft970915_1153_2050G300670H.fits[2] ft970915_1153_2050G300770H.fits[2] ft970915_1153_2050G300870M.fits[2] ft970915_1153_2050G300970M.fits[2] ft970915_1153_2050G301070H.fits[2] ft970915_1153_2050G301170H.fits[2] ft970915_1153_2050G301270H.fits[2] ft970915_1153_2050G301370H.fits[2] ft970915_1153_2050G301470L.fits[2] ft970915_1153_2050G301570L.fits[2] ft970915_1153_2050G301670M.fits[2] ft970915_1153_2050G301770H.fits[2] ft970915_1153_2050G301870H.fits[2] ft970915_1153_2050G301970H.fits[2] ft970915_1153_2050G302070H.fits[2] ft970915_1153_2050G302570M.fits[2] ft970915_1153_2050G302670M.fits[2] ft970915_1153_2050G302770H.fits[2] ft970915_1153_2050G302870H.fits[2] ft970915_1153_2050G302970H.fits[2] ft970915_1153_2050G303070H.fits[2] ft970915_1153_2050G303170L.fits[2] ft970915_1153_2050G303270L.fits[2] ft970915_1153_2050G303370H.fits[2] ft970915_1153_2050G303470H.fits[2] ft970915_1153_2050G303570H.fits[2] ft970915_1153_2050G303670H.fits[2] ft970915_1153_2050G303770M.fits[2] ft970915_1153_2050G303870M.fits[2] ft970915_1153_2050G303970M.fits[2] ft970915_1153_2050G304670M.fits[2] ft970915_1153_2050G304770M.fits[2] ft970915_1153_2050G304870L.fits[2] ft970915_1153_2050G304970L.fits[2] ft970915_1153_2050G305070M.fits[2] ft970915_1153_2050G305170M.fits[2] ft970915_1153_2050G305270M.fits[2] ft970915_1153_2050G305370M.fits[2] ft970915_1153_2050G305470M.fits[2] ft970915_1153_2050G306270H.fits[2] ft970915_1153_2050G306370H.fits[2] ft970915_1153_2050G306470H.fits[2] ft970915_1153_2050G306570H.fits[2] ft970915_1153_2050G306670L.fits[2] ft970915_1153_2050G306770H.fits[2] ft970915_1153_2050G306870H.fits[2] ft970915_1153_2050G307870H.fits[2] ft970915_1153_2050G307970H.fits[2] ft970915_1153_2050G308070H.fits[2] ft970915_1153_2050G308170H.fits[2] ft970915_1153_2050G308270M.fits[2] ft970915_1153_2050G308370M.fits[2] ft970915_1153_2050G308470M.fits[2] ft970915_1153_2050G308970H.fits[2]
GISSORTCODE:LO:Start program GISSORTCODE:LO:End program-> Standard Error Output From STOOL gissortsplit:
GISSORTSPLIT:LO:Start program GISSORTSPLIT:LO:g200170h.prelist merge count = 1 photon cnt = 7 GISSORTSPLIT:LO:g200270h.prelist merge count = 1 photon cnt = 3 GISSORTSPLIT:LO:g200370h.prelist merge count = 2 photon cnt = 14 GISSORTSPLIT:LO:g200470h.prelist merge count = 8 photon cnt = 24476 GISSORTSPLIT:LO:g200570h.prelist merge count = 5 photon cnt = 52 GISSORTSPLIT:LO:g200670h.prelist merge count = 1 photon cnt = 11 GISSORTSPLIT:LO:g200770h.prelist merge count = 1 photon cnt = 11 GISSORTSPLIT:LO:g200870h.prelist merge count = 1 photon cnt = 12 GISSORTSPLIT:LO:g200970h.prelist merge count = 1 photon cnt = 5 GISSORTSPLIT:LO:g201070h.prelist merge count = 1 photon cnt = 7 GISSORTSPLIT:LO:g201170h.prelist merge count = 1 photon cnt = 10 GISSORTSPLIT:LO:g201270h.prelist merge count = 1 photon cnt = 7 GISSORTSPLIT:LO:g201370h.prelist merge count = 1 photon cnt = 6 GISSORTSPLIT:LO:g201470h.prelist merge count = 1 photon cnt = 8 GISSORTSPLIT:LO:g201570h.prelist merge count = 1 photon cnt = 10 GISSORTSPLIT:LO:g200170l.prelist merge count = 5 photon cnt = 13534 GISSORTSPLIT:LO:g200270l.prelist merge count = 3 photon cnt = 187 GISSORTSPLIT:LO:g200170m.prelist merge count = 3 photon cnt = 70 GISSORTSPLIT:LO:g200270m.prelist merge count = 2 photon cnt = 31 GISSORTSPLIT:LO:g200370m.prelist merge count = 9 photon cnt = 25275 GISSORTSPLIT:LO:g200470m.prelist merge count = 4 photon cnt = 384 GISSORTSPLIT:LO:g200570m.prelist merge count = 1 photon cnt = 85 GISSORTSPLIT:LO:g200670m.prelist merge count = 1 photon cnt = 79 GISSORTSPLIT:LO:Total filenames split = 55 GISSORTSPLIT:LO:Total split file cnt = 23 GISSORTSPLIT:LO:End program-> Creating ad45016000g200170m.unf
---- cmerge: version 1.6 ---- A total of 9 fits files ...... Sorting files using KEY: TSTART ... Checking GTI overlap in input files ... Merging binary extension #: 1 1 -- ft970915_1153_2050G200170M.fits 2 -- ft970915_1153_2050G200370M.fits 3 -- ft970915_1153_2050G200970M.fits 4 -- ft970915_1153_2050G201670M.fits 5 -- ft970915_1153_2050G202570M.fits 6 -- ft970915_1153_2050G203770M.fits 7 -- ft970915_1153_2050G204670M.fits 8 -- ft970915_1153_2050G205270M.fits 9 -- ft970915_1153_2050G208270M.fits Merging binary extension #: 2 1 -- ft970915_1153_2050G200170M.fits 2 -- ft970915_1153_2050G200370M.fits 3 -- ft970915_1153_2050G200970M.fits 4 -- ft970915_1153_2050G201670M.fits 5 -- ft970915_1153_2050G202570M.fits 6 -- ft970915_1153_2050G203770M.fits 7 -- ft970915_1153_2050G204670M.fits 8 -- ft970915_1153_2050G205270M.fits 9 -- ft970915_1153_2050G208270M.fits Checking the output file ... Extention # 1 ...... OK Extention # 2 ...... OK The program appears to have finished successfully!-> Creating ad45016000g200270h.unf
---- cmerge: version 1.6 ---- A total of 8 fits files ...... Sorting files using KEY: TSTART ... Checking GTI overlap in input files ... Merging binary extension #: 1 1 -- ft970915_1153_2050G200770H.fits 2 -- ft970915_1153_2050G201370H.fits 3 -- ft970915_1153_2050G202070H.fits 4 -- ft970915_1153_2050G202970H.fits 5 -- ft970915_1153_2050G203570H.fits 6 -- ft970915_1153_2050G206470H.fits 7 -- ft970915_1153_2050G206670H.fits 8 -- ft970915_1153_2050G208070H.fits Merging binary extension #: 2 1 -- ft970915_1153_2050G200770H.fits 2 -- ft970915_1153_2050G201370H.fits 3 -- ft970915_1153_2050G202070H.fits 4 -- ft970915_1153_2050G202970H.fits 5 -- ft970915_1153_2050G203570H.fits 6 -- ft970915_1153_2050G206470H.fits 7 -- ft970915_1153_2050G206670H.fits 8 -- ft970915_1153_2050G208070H.fits Checking the output file ... Extention # 1 ...... OK Extention # 2 ...... OK The program appears to have finished successfully!-> Creating ad45016000g200370l.unf
---- cmerge: version 1.6 ---- A total of 5 fits files ...... Sorting files using KEY: TSTART ... Checking GTI overlap in input files ... Merging binary extension #: 1 1 -- ft970915_1153_2050G200270L.fits 2 -- ft970915_1153_2050G201570L.fits 3 -- ft970915_1153_2050G203170L.fits 4 -- ft970915_1153_2050G204870L.fits 5 -- ft970915_1153_2050G206570L.fits Merging binary extension #: 2 1 -- ft970915_1153_2050G200270L.fits 2 -- ft970915_1153_2050G201570L.fits 3 -- ft970915_1153_2050G203170L.fits 4 -- ft970915_1153_2050G204870L.fits 5 -- ft970915_1153_2050G206570L.fits Checking the output file ... Extention # 1 ...... OK Extention # 2 ...... OK The program appears to have finished successfully!-> Ignoring the following files containing 000000384 events
ft970915_1153_2050G200870M.fits ft970915_1153_2050G203670M.fits ft970915_1153_2050G205170M.fits ft970915_1153_2050G208170M.fits-> Ignoring the following files containing 000000187 events
ft970915_1153_2050G201470L.fits ft970915_1153_2050G203070L.fits ft970915_1153_2050G204770L.fits-> Ignoring the following files containing 000000085 events
ft970915_1153_2050G204970M.fits-> Ignoring the following files containing 000000079 events
ft970915_1153_2050G205070M.fits-> Ignoring the following files containing 000000070 events
ft970915_1153_2050G203870M.fits ft970915_1153_2050G205370M.fits ft970915_1153_2050G208370M.fits-> Ignoring the following files containing 000000052 events
ft970915_1153_2050G200670H.fits ft970915_1153_2050G201270H.fits ft970915_1153_2050G201970H.fits ft970915_1153_2050G202870H.fits ft970915_1153_2050G203470H.fits-> Ignoring the following files containing 000000031 events
ft970915_1153_2050G202470M.fits ft970915_1153_2050G204570M.fits-> Ignoring the following files containing 000000014 events
ft970915_1153_2050G206370H.fits ft970915_1153_2050G207970H.fits-> Ignoring the following files containing 000000012 events
ft970915_1153_2050G203270H.fits-> Ignoring the following files containing 000000011 events
ft970915_1153_2050G201870H.fits-> Ignoring the following files containing 000000011 events
ft970915_1153_2050G201770H.fits-> Ignoring the following files containing 000000010 events
ft970915_1153_2050G201170H.fits-> Ignoring the following files containing 000000010 events
ft970915_1153_2050G202770H.fits-> Ignoring the following files containing 000000008 events
ft970915_1153_2050G201070H.fits-> Ignoring the following files containing 000000007 events
ft970915_1153_2050G200470H.fits-> Ignoring the following files containing 000000007 events
ft970915_1153_2050G202670H.fits-> Ignoring the following files containing 000000007 events
ft970915_1153_2050G206770H.fits-> Ignoring the following files containing 000000006 events
ft970915_1153_2050G200570H.fits-> Ignoring the following files containing 000000005 events
ft970915_1153_2050G203370H.fits-> Ignoring the following files containing 000000003 events
ft970915_1153_2050G206270H.fits-> Collecting GIS3 event files by mode
GISSORTCODE:LO:Start program GISSORTCODE:LO:End program-> Standard Error Output From STOOL gissortsplit:
GISSORTSPLIT:LO:Start program GISSORTSPLIT:LO:g300170h.prelist merge count = 1 photon cnt = 4 GISSORTSPLIT:LO:g300270h.prelist merge count = 3 photon cnt = 5 GISSORTSPLIT:LO:g300370h.prelist merge count = 2 photon cnt = 14 GISSORTSPLIT:LO:g300470h.prelist merge count = 2 photon cnt = 15 GISSORTSPLIT:LO:g300570h.prelist merge count = 8 photon cnt = 23715 GISSORTSPLIT:LO:g300670h.prelist merge count = 5 photon cnt = 35 GISSORTSPLIT:LO:g300770h.prelist merge count = 1 photon cnt = 8 GISSORTSPLIT:LO:g300870h.prelist merge count = 1 photon cnt = 6 GISSORTSPLIT:LO:g300970h.prelist merge count = 1 photon cnt = 7 GISSORTSPLIT:LO:g301070h.prelist merge count = 1 photon cnt = 7 GISSORTSPLIT:LO:g301170h.prelist merge count = 1 photon cnt = 5 GISSORTSPLIT:LO:g301270h.prelist merge count = 1 photon cnt = 9 GISSORTSPLIT:LO:g301370h.prelist merge count = 1 photon cnt = 8 GISSORTSPLIT:LO:g301470h.prelist merge count = 1 photon cnt = 14 GISSORTSPLIT:LO:g301570h.prelist merge count = 1 photon cnt = 8 GISSORTSPLIT:LO:g301670h.prelist merge count = 1 photon cnt = 10 GISSORTSPLIT:LO:g300170l.prelist merge count = 5 photon cnt = 13152 GISSORTSPLIT:LO:g300270l.prelist merge count = 3 photon cnt = 159 GISSORTSPLIT:LO:g300170m.prelist merge count = 3 photon cnt = 64 GISSORTSPLIT:LO:g300270m.prelist merge count = 2 photon cnt = 17 GISSORTSPLIT:LO:g300370m.prelist merge count = 9 photon cnt = 25079 GISSORTSPLIT:LO:g300470m.prelist merge count = 4 photon cnt = 317 GISSORTSPLIT:LO:g300570m.prelist merge count = 1 photon cnt = 88 GISSORTSPLIT:LO:g300670m.prelist merge count = 1 photon cnt = 79 GISSORTSPLIT:LO:Total filenames split = 59 GISSORTSPLIT:LO:Total split file cnt = 24 GISSORTSPLIT:LO:End program-> Creating ad45016000g300170m.unf
---- cmerge: version 1.6 ---- A total of 9 fits files ...... Sorting files using KEY: TSTART ... Checking GTI overlap in input files ... Merging binary extension #: 1 1 -- ft970915_1153_2050G300170M.fits 2 -- ft970915_1153_2050G300370M.fits 3 -- ft970915_1153_2050G300970M.fits 4 -- ft970915_1153_2050G301670M.fits 5 -- ft970915_1153_2050G302670M.fits 6 -- ft970915_1153_2050G303870M.fits 7 -- ft970915_1153_2050G304770M.fits 8 -- ft970915_1153_2050G305370M.fits 9 -- ft970915_1153_2050G308370M.fits Merging binary extension #: 2 1 -- ft970915_1153_2050G300170M.fits 2 -- ft970915_1153_2050G300370M.fits 3 -- ft970915_1153_2050G300970M.fits 4 -- ft970915_1153_2050G301670M.fits 5 -- ft970915_1153_2050G302670M.fits 6 -- ft970915_1153_2050G303870M.fits 7 -- ft970915_1153_2050G304770M.fits 8 -- ft970915_1153_2050G305370M.fits 9 -- ft970915_1153_2050G308370M.fits Checking the output file ... Extention # 1 ...... OK Extention # 2 ...... OK The program appears to have finished successfully!-> Creating ad45016000g300270h.unf
---- cmerge: version 1.6 ---- A total of 8 fits files ...... Sorting files using KEY: TSTART ... Checking GTI overlap in input files ... Merging binary extension #: 1 1 -- ft970915_1153_2050G300770H.fits 2 -- ft970915_1153_2050G301370H.fits 3 -- ft970915_1153_2050G302070H.fits 4 -- ft970915_1153_2050G303070H.fits 5 -- ft970915_1153_2050G303670H.fits 6 -- ft970915_1153_2050G306570H.fits 7 -- ft970915_1153_2050G306770H.fits 8 -- ft970915_1153_2050G308170H.fits Merging binary extension #: 2 1 -- ft970915_1153_2050G300770H.fits 2 -- ft970915_1153_2050G301370H.fits 3 -- ft970915_1153_2050G302070H.fits 4 -- ft970915_1153_2050G303070H.fits 5 -- ft970915_1153_2050G303670H.fits 6 -- ft970915_1153_2050G306570H.fits 7 -- ft970915_1153_2050G306770H.fits 8 -- ft970915_1153_2050G308170H.fits Checking the output file ... Extention # 1 ...... OK Extention # 2 ...... OK The program appears to have finished successfully!-> Creating ad45016000g300370l.unf
---- cmerge: version 1.6 ---- A total of 5 fits files ...... Sorting files using KEY: TSTART ... Checking GTI overlap in input files ... Merging binary extension #: 1 1 -- ft970915_1153_2050G300270L.fits 2 -- ft970915_1153_2050G301570L.fits 3 -- ft970915_1153_2050G303270L.fits 4 -- ft970915_1153_2050G304970L.fits 5 -- ft970915_1153_2050G306670L.fits Merging binary extension #: 2 1 -- ft970915_1153_2050G300270L.fits 2 -- ft970915_1153_2050G301570L.fits 3 -- ft970915_1153_2050G303270L.fits 4 -- ft970915_1153_2050G304970L.fits 5 -- ft970915_1153_2050G306670L.fits Checking the output file ... Extention # 1 ...... OK Extention # 2 ...... OK The program appears to have finished successfully!-> Ignoring the following files containing 000000317 events
ft970915_1153_2050G300870M.fits ft970915_1153_2050G303770M.fits ft970915_1153_2050G305270M.fits ft970915_1153_2050G308270M.fits-> Ignoring the following files containing 000000159 events
ft970915_1153_2050G301470L.fits ft970915_1153_2050G303170L.fits ft970915_1153_2050G304870L.fits-> Ignoring the following files containing 000000088 events
ft970915_1153_2050G305070M.fits-> Ignoring the following files containing 000000079 events
ft970915_1153_2050G305170M.fits-> Ignoring the following files containing 000000064 events
ft970915_1153_2050G303970M.fits ft970915_1153_2050G305470M.fits ft970915_1153_2050G308470M.fits-> Ignoring the following files containing 000000035 events
ft970915_1153_2050G300670H.fits ft970915_1153_2050G301270H.fits ft970915_1153_2050G301970H.fits ft970915_1153_2050G302970H.fits ft970915_1153_2050G303570H.fits-> Ignoring the following files containing 000000017 events
ft970915_1153_2050G302570M.fits ft970915_1153_2050G304670M.fits-> Ignoring the following files containing 000000015 events
ft970915_1153_2050G306470H.fits ft970915_1153_2050G308070H.fits-> Ignoring the following files containing 000000014 events
ft970915_1153_2050G301170H.fits-> Ignoring the following files containing 000000014 events
ft970915_1153_2050G306370H.fits ft970915_1153_2050G307970H.fits-> Ignoring the following files containing 000000010 events
ft970915_1153_2050G303470H.fits-> Ignoring the following files containing 000000009 events
ft970915_1153_2050G300570H.fits-> Ignoring the following files containing 000000008 events
ft970915_1153_2050G303370H.fits-> Ignoring the following files containing 000000008 events
ft970915_1153_2050G301070H.fits-> Ignoring the following files containing 000000008 events
ft970915_1153_2050G302770H.fits-> Ignoring the following files containing 000000007 events
ft970915_1153_2050G301870H.fits-> Ignoring the following files containing 000000007 events
ft970915_1153_2050G301770H.fits-> Ignoring the following files containing 000000006 events
ft970915_1153_2050G302870H.fits-> Ignoring the following files containing 000000005 events
ft970915_1153_2050G300470H.fits-> Ignoring the following files containing 000000005 events
ft970915_1153_2050G306270H.fits ft970915_1153_2050G307870H.fits ft970915_1153_2050G308970H.fits-> Ignoring the following files containing 000000004 events
ft970915_1153_2050G306870H.fits-> Collecting SIS0 event files by mode
SIS0SORTCODE:LO:Start program SIS0SORTCODE:LO:End program-> Standard Error Output From STOOL sis0sortsplit:
SIS0SORTSPLIT:LO:Start program SIS0SORTSPLIT:LO:s000101h.prelist merge count = 9 photon cnt = 88142 SIS0SORTSPLIT:LO:s000201l.prelist merge count = 7 photon cnt = 18068 SIS0SORTSPLIT:LO:s000301l.prelist merge count = 1 photon cnt = 95 SIS0SORTSPLIT:LO:s000401m.prelist merge count = 11 photon cnt = 28496 SIS0SORTSPLIT:LO:s000501m.prelist merge count = 1 photon cnt = 32 SIS0SORTSPLIT:LO:Total filenames split = 29 SIS0SORTSPLIT:LO:Total split file cnt = 5 SIS0SORTSPLIT:LO:End program-> Creating ad45016000s000101h.unf
---- cmerge: version 1.6 ---- A total of 9 fits files ...... Sorting files using KEY: TSTART ... Checking GTI overlap in input files ... Merging binary extension #: 1 1 -- ft970915_1153_2050S000401H.fits 2 -- ft970915_1153_2050S000601H.fits 3 -- ft970915_1153_2050S000901H.fits 4 -- ft970915_1153_2050S001101H.fits 5 -- ft970915_1153_2050S001301H.fits 6 -- ft970915_1153_2050S002201H.fits 7 -- ft970915_1153_2050S002401H.fits 8 -- ft970915_1153_2050S002901H.fits 9 -- ft970915_1153_2050S003101H.fits Merging binary extension #: 2 1 -- ft970915_1153_2050S000401H.fits 2 -- ft970915_1153_2050S000601H.fits 3 -- ft970915_1153_2050S000901H.fits 4 -- ft970915_1153_2050S001101H.fits 5 -- ft970915_1153_2050S001301H.fits 6 -- ft970915_1153_2050S002201H.fits 7 -- ft970915_1153_2050S002401H.fits 8 -- ft970915_1153_2050S002901H.fits 9 -- ft970915_1153_2050S003101H.fits Checking the output file ... Extention # 1 ...... OK Extention # 2 ...... OK The program appears to have finished successfully!-> Creating ad45016000s000201m.unf
---- cmerge: version 1.6 ---- A total of 11 fits files ...... Sorting files using KEY: TSTART ... Checking GTI overlap in input files ... Merging binary extension #: 1 1 -- ft970915_1153_2050S000101M.fits 2 -- ft970915_1153_2050S000301M.fits 3 -- ft970915_1153_2050S000501M.fits 4 -- ft970915_1153_2050S000801M.fits 5 -- ft970915_1153_2050S001001M.fits 6 -- ft970915_1153_2050S001401M.fits 7 -- ft970915_1153_2050S001601M.fits 8 -- ft970915_1153_2050S001801M.fits 9 -- ft970915_1153_2050S002501M.fits 10 -- ft970915_1153_2050S002801M.fits 11 -- ft970915_1153_2050S003001M.fits Merging binary extension #: 2 1 -- ft970915_1153_2050S000101M.fits 2 -- ft970915_1153_2050S000301M.fits 3 -- ft970915_1153_2050S000501M.fits 4 -- ft970915_1153_2050S000801M.fits 5 -- ft970915_1153_2050S001001M.fits 6 -- ft970915_1153_2050S001401M.fits 7 -- ft970915_1153_2050S001601M.fits 8 -- ft970915_1153_2050S001801M.fits 9 -- ft970915_1153_2050S002501M.fits 10 -- ft970915_1153_2050S002801M.fits 11 -- ft970915_1153_2050S003001M.fits Checking the output file ... Extention # 1 ...... OK Extention # 2 ...... OK The program appears to have finished successfully!-> Creating ad45016000s000301l.unf
---- cmerge: version 1.6 ---- A total of 7 fits files ...... Sorting files using KEY: TSTART ... Checking GTI overlap in input files ... Merging binary extension #: 1 1 -- ft970915_1153_2050S000201L.fits 2 -- ft970915_1153_2050S000701L.fits 3 -- ft970915_1153_2050S001201L.fits 4 -- ft970915_1153_2050S001501L.fits 5 -- ft970915_1153_2050S001701L.fits 6 -- ft970915_1153_2050S002101L.fits 7 -- ft970915_1153_2050S002301L.fits Merging binary extension #: 2 1 -- ft970915_1153_2050S000201L.fits 2 -- ft970915_1153_2050S000701L.fits 3 -- ft970915_1153_2050S001201L.fits 4 -- ft970915_1153_2050S001501L.fits 5 -- ft970915_1153_2050S001701L.fits 6 -- ft970915_1153_2050S002101L.fits 7 -- ft970915_1153_2050S002301L.fits Checking the output file ... Extention # 1 ...... OK Extention # 2 ...... OK The program appears to have finished successfully!-> Ignoring the following files containing 000000095 events
ft970915_1153_2050S002001L.fits-> Ignoring the following files containing 000000032 events
ft970915_1153_2050S002601M.fits-> Collecting SIS1 event files by mode
SIS1SORTCODE:LO:Start program SIS1SORTCODE:LO:End program-> Standard Error Output From STOOL sis1sortsplit:
SIS1SORTSPLIT:LO:Start program SIS1SORTSPLIT:LO:s100101h.prelist merge count = 9 photon cnt = 83332 SIS1SORTSPLIT:LO:s100201l.prelist merge count = 7 photon cnt = 21091 SIS1SORTSPLIT:LO:s100301l.prelist merge count = 1 photon cnt = 96 SIS1SORTSPLIT:LO:s100401m.prelist merge count = 11 photon cnt = 39724 SIS1SORTSPLIT:LO:s100501m.prelist merge count = 1 photon cnt = 32 SIS1SORTSPLIT:LO:Total filenames split = 29 SIS1SORTSPLIT:LO:Total split file cnt = 5 SIS1SORTSPLIT:LO:End program-> Creating ad45016000s100101h.unf
---- cmerge: version 1.6 ---- A total of 9 fits files ...... Sorting files using KEY: TSTART ... Checking GTI overlap in input files ... Merging binary extension #: 1 1 -- ft970915_1153_2050S100401H.fits 2 -- ft970915_1153_2050S100601H.fits 3 -- ft970915_1153_2050S100901H.fits 4 -- ft970915_1153_2050S101101H.fits 5 -- ft970915_1153_2050S101301H.fits 6 -- ft970915_1153_2050S102201H.fits 7 -- ft970915_1153_2050S102401H.fits 8 -- ft970915_1153_2050S102901H.fits 9 -- ft970915_1153_2050S103101H.fits Merging binary extension #: 2 1 -- ft970915_1153_2050S100401H.fits 2 -- ft970915_1153_2050S100601H.fits 3 -- ft970915_1153_2050S100901H.fits 4 -- ft970915_1153_2050S101101H.fits 5 -- ft970915_1153_2050S101301H.fits 6 -- ft970915_1153_2050S102201H.fits 7 -- ft970915_1153_2050S102401H.fits 8 -- ft970915_1153_2050S102901H.fits 9 -- ft970915_1153_2050S103101H.fits Checking the output file ... Extention # 1 ...... OK Extention # 2 ...... OK The program appears to have finished successfully!-> Creating ad45016000s100201m.unf
---- cmerge: version 1.6 ---- A total of 11 fits files ...... Sorting files using KEY: TSTART ... Checking GTI overlap in input files ... Merging binary extension #: 1 1 -- ft970915_1153_2050S100101M.fits 2 -- ft970915_1153_2050S100301M.fits 3 -- ft970915_1153_2050S100501M.fits 4 -- ft970915_1153_2050S100801M.fits 5 -- ft970915_1153_2050S101001M.fits 6 -- ft970915_1153_2050S101401M.fits 7 -- ft970915_1153_2050S101601M.fits 8 -- ft970915_1153_2050S101801M.fits 9 -- ft970915_1153_2050S102501M.fits 10 -- ft970915_1153_2050S102801M.fits 11 -- ft970915_1153_2050S103001M.fits Merging binary extension #: 2 1 -- ft970915_1153_2050S100101M.fits 2 -- ft970915_1153_2050S100301M.fits 3 -- ft970915_1153_2050S100501M.fits 4 -- ft970915_1153_2050S100801M.fits 5 -- ft970915_1153_2050S101001M.fits 6 -- ft970915_1153_2050S101401M.fits 7 -- ft970915_1153_2050S101601M.fits 8 -- ft970915_1153_2050S101801M.fits 9 -- ft970915_1153_2050S102501M.fits 10 -- ft970915_1153_2050S102801M.fits 11 -- ft970915_1153_2050S103001M.fits Checking the output file ... Extention # 1 ...... OK Extention # 2 ...... OK The program appears to have finished successfully!-> Creating ad45016000s100301l.unf
---- cmerge: version 1.6 ---- A total of 7 fits files ...... Sorting files using KEY: TSTART ... Checking GTI overlap in input files ... Merging binary extension #: 1 1 -- ft970915_1153_2050S100201L.fits 2 -- ft970915_1153_2050S100701L.fits 3 -- ft970915_1153_2050S101201L.fits 4 -- ft970915_1153_2050S101501L.fits 5 -- ft970915_1153_2050S101701L.fits 6 -- ft970915_1153_2050S102101L.fits 7 -- ft970915_1153_2050S102301L.fits Merging binary extension #: 2 1 -- ft970915_1153_2050S100201L.fits 2 -- ft970915_1153_2050S100701L.fits 3 -- ft970915_1153_2050S101201L.fits 4 -- ft970915_1153_2050S101501L.fits 5 -- ft970915_1153_2050S101701L.fits 6 -- ft970915_1153_2050S102101L.fits 7 -- ft970915_1153_2050S102301L.fits Checking the output file ... Extention # 1 ...... OK Extention # 2 ...... OK The program appears to have finished successfully!-> Ignoring the following files containing 000000096 events
ft970915_1153_2050S102001L.fits-> Ignoring the following files containing 000000032 events
ft970915_1153_2050S102601M.fits-> Tar-ing together the leftover raw files
a ft970915_1153_2050G200470H.fits 31K a ft970915_1153_2050G200570H.fits 31K a ft970915_1153_2050G200670H.fits 31K a ft970915_1153_2050G200870M.fits 34K a ft970915_1153_2050G201070H.fits 31K a ft970915_1153_2050G201170H.fits 31K a ft970915_1153_2050G201270H.fits 31K a ft970915_1153_2050G201470L.fits 31K a ft970915_1153_2050G201770H.fits 31K a ft970915_1153_2050G201870H.fits 31K a ft970915_1153_2050G201970H.fits 31K a ft970915_1153_2050G202470M.fits 31K a ft970915_1153_2050G202670H.fits 31K a ft970915_1153_2050G202770H.fits 31K a ft970915_1153_2050G202870H.fits 31K a ft970915_1153_2050G203070L.fits 31K a ft970915_1153_2050G203270H.fits 31K a ft970915_1153_2050G203370H.fits 31K a ft970915_1153_2050G203470H.fits 31K a ft970915_1153_2050G203670M.fits 34K a ft970915_1153_2050G203870M.fits 31K a ft970915_1153_2050G204570M.fits 31K a ft970915_1153_2050G204770L.fits 31K a ft970915_1153_2050G204970M.fits 31K a ft970915_1153_2050G205070M.fits 31K a ft970915_1153_2050G205170M.fits 31K a ft970915_1153_2050G205370M.fits 31K a ft970915_1153_2050G206270H.fits 31K a ft970915_1153_2050G206370H.fits 31K a ft970915_1153_2050G206770H.fits 31K a ft970915_1153_2050G207970H.fits 31K a ft970915_1153_2050G208170M.fits 31K a ft970915_1153_2050G208370M.fits 31K a ft970915_1153_2050G300470H.fits 31K a ft970915_1153_2050G300570H.fits 31K a ft970915_1153_2050G300670H.fits 31K a ft970915_1153_2050G300870M.fits 34K a ft970915_1153_2050G301070H.fits 31K a ft970915_1153_2050G301170H.fits 31K a ft970915_1153_2050G301270H.fits 31K a ft970915_1153_2050G301470L.fits 31K a ft970915_1153_2050G301770H.fits 31K a ft970915_1153_2050G301870H.fits 31K a ft970915_1153_2050G301970H.fits 31K a ft970915_1153_2050G302570M.fits 31K a ft970915_1153_2050G302770H.fits 31K a ft970915_1153_2050G302870H.fits 31K a ft970915_1153_2050G302970H.fits 31K a ft970915_1153_2050G303170L.fits 31K a ft970915_1153_2050G303370H.fits 31K a ft970915_1153_2050G303470H.fits 31K a ft970915_1153_2050G303570H.fits 31K a ft970915_1153_2050G303770M.fits 34K a ft970915_1153_2050G303970M.fits 31K a ft970915_1153_2050G304670M.fits 31K a ft970915_1153_2050G304870L.fits 31K a ft970915_1153_2050G305070M.fits 31K a ft970915_1153_2050G305170M.fits 31K a ft970915_1153_2050G305270M.fits 31K a ft970915_1153_2050G305470M.fits 31K a ft970915_1153_2050G306270H.fits 31K a ft970915_1153_2050G306370H.fits 31K a ft970915_1153_2050G306470H.fits 31K a ft970915_1153_2050G306870H.fits 31K a ft970915_1153_2050G307870H.fits 31K a ft970915_1153_2050G307970H.fits 31K a ft970915_1153_2050G308070H.fits 31K a ft970915_1153_2050G308270M.fits 31K a ft970915_1153_2050G308470M.fits 31K a ft970915_1153_2050G308970H.fits 31K a ft970915_1153_2050S002001L.fits 31K a ft970915_1153_2050S002601M.fits 29K a ft970915_1153_2050S102001L.fits 31K a ft970915_1153_2050S102601M.fits 29K-> Checking OBJECT keywords in HK and event files
temp2gain v4.3 'ft970915_1153.2050' is successfully opened Data Start Time is 148477999.43 (19970915 115315) Time Margin 2.0 sec included Sync error detected in 25 th SF Sync error detected in 49 th SF Sync error detected in 3965 th SF 'ft970915_1153.2050' EOF detected, sf=5361 Data End Time is 148596645.04 (19970916 205041) Gain History is written in ft970915_1153_2050.ghf-> Stdout output from ISAS program temp2gain
leapsec FITS data was successfully read-> Checking if column CAL_START in ft970915_1153_2050.ghf[1] is in order
Time column is TIME ORDERED-> Checking if column CAL_STOP in ft970915_1153_2050.ghf[1] is in order
Time column is TIME ORDERED-> Calculating attitude correction from ft970915_1153_2050CMHK.fits
The sum of the selected column is 18381.000 The mean of the selected column is 96.235602 The standard deviation of the selected column is 1.6864755 The minimum of selected column is 93.000000 The maximum of selected column is 100.00000 The number of points used in calculation is 191-> Standard Output From FTOOL fstatistic:
The sum of the selected column is 18381.000 The mean of the selected column is 96.235602 The standard deviation of the selected column is 1.6864755 The minimum of selected column is 93.000000 The maximum of selected column is 100.00000 The number of points used in calculation is 191
ASCALIN_V0.9u(mod)-> Standard Error Output From FTOOL ascalin
ASCALIN_V0.9u(mod) : Detected gap > 15min in attitude file: 148479629.42616 ASCALIN_V0.9u(mod) : Detected gap > 15min in attitude file:-> Checking if ad45016000g200270h.unf is covered by attitude file
ASCALIN_V0.9u(mod)-> Checking if ad45016000g200370l.unf is covered by attitude file
ASCALIN_V0.9u(mod)-> Standard Error Output From FTOOL ascalin
ASCALIN_V0.9u(mod) : Detected gap > 15min in attitude file: 148479629.42616 ASCALIN_V0.9u(mod) : Detected gap > 15min in attitude file:-> Checking if ad45016000g300170m.unf is covered by attitude file
ASCALIN_V0.9u(mod)-> Standard Error Output From FTOOL ascalin
ASCALIN_V0.9u(mod) : Detected gap > 15min in attitude file: 148479629.42616 ASCALIN_V0.9u(mod) : Detected gap > 15min in attitude file:-> Checking if ad45016000g300270h.unf is covered by attitude file
ASCALIN_V0.9u(mod)-> Checking if ad45016000g300370l.unf is covered by attitude file
ASCALIN_V0.9u(mod)-> Standard Error Output From FTOOL ascalin
ASCALIN_V0.9u(mod) : Detected gap > 15min in attitude file: 148479629.42616 ASCALIN_V0.9u(mod) : Detected gap > 15min in attitude file:-> Checking if ad45016000s000101h.unf is covered by attitude file
ASCALIN_V0.9u(mod)-> Standard Error Output From FTOOL ascalin
ASCALIN_V0.9u(mod) : Detected gap > 15min in attitude file: 148507737.33208 ASCALIN_V0.9u(mod) : Detected gap > 15min in attitude file:-> Checking if ad45016000s000102h.unf is covered by attitude file
ASCALIN_V0.9u(mod)-> Standard Error Output From FTOOL ascalin
ASCALIN_V0.9u(mod) : Detected gap > 15min in attitude file: 148507737.33208 ASCALIN_V0.9u(mod) : Detected gap > 15min in attitude file:-> Checking if ad45016000s000112h.unf is covered by attitude file
ASCALIN_V0.9u(mod)-> Standard Error Output From FTOOL ascalin
ASCALIN_V0.9u(mod) : Detected gap > 15min in attitude file: 148507737.33208 ASCALIN_V0.9u(mod) : Detected gap > 15min in attitude file:-> Checking if ad45016000s000201m.unf is covered by attitude file
ASCALIN_V0.9u(mod)-> Standard Error Output From FTOOL ascalin
ASCALIN_V0.9u(mod) : Detected gap > 15min in attitude file: 148479629.42616 ASCALIN_V0.9u(mod) : Detected gap > 15min in attitude file:-> Checking if ad45016000s000202m.unf is covered by attitude file
ASCALIN_V0.9u(mod)-> Standard Error Output From FTOOL ascalin
ASCALIN_V0.9u(mod) : Detected gap > 15min in attitude file: 148479629.42616 ASCALIN_V0.9u(mod) : Detected gap > 15min in attitude file:-> Checking if ad45016000s000212m.unf is covered by attitude file
ASCALIN_V0.9u(mod)-> Standard Error Output From FTOOL ascalin
ASCALIN_V0.9u(mod) : Detected gap > 15min in attitude file: 148479629.42616 ASCALIN_V0.9u(mod) : Detected gap > 15min in attitude file:-> Checking if ad45016000s000301l.unf is covered by attitude file
ASCALIN_V0.9u(mod)-> Standard Error Output From FTOOL ascalin
ASCALIN_V0.9u(mod) : Detected gap > 15min in attitude file: 148479629.42616 ASCALIN_V0.9u(mod) : Detected gap > 15min in attitude file:-> Checking if ad45016000s000302l.unf is covered by attitude file
ASCALIN_V0.9u(mod)-> Standard Error Output From FTOOL ascalin
ASCALIN_V0.9u(mod) : Detected gap > 15min in attitude file: 148479629.42616 ASCALIN_V0.9u(mod) : Detected gap > 15min in attitude file:-> Checking if ad45016000s000312l.unf is covered by attitude file
ASCALIN_V0.9u(mod)-> Standard Error Output From FTOOL ascalin
ASCALIN_V0.9u(mod) : Detected gap > 15min in attitude file: 148479629.42616 ASCALIN_V0.9u(mod) : Detected gap > 15min in attitude file:-> Checking if ad45016000s100101h.unf is covered by attitude file
ASCALIN_V0.9u(mod)-> Standard Error Output From FTOOL ascalin
ASCALIN_V0.9u(mod) : Detected gap > 15min in attitude file: 148507737.33208 ASCALIN_V0.9u(mod) : Detected gap > 15min in attitude file:-> Checking if ad45016000s100102h.unf is covered by attitude file
ASCALIN_V0.9u(mod)-> Standard Error Output From FTOOL ascalin
ASCALIN_V0.9u(mod) : Detected gap > 15min in attitude file: 148507737.33208 ASCALIN_V0.9u(mod) : Detected gap > 15min in attitude file:-> Checking if ad45016000s100112h.unf is covered by attitude file
ASCALIN_V0.9u(mod)-> Standard Error Output From FTOOL ascalin
ASCALIN_V0.9u(mod) : Detected gap > 15min in attitude file: 148507737.33208 ASCALIN_V0.9u(mod) : Detected gap > 15min in attitude file:-> Checking if ad45016000s100201m.unf is covered by attitude file
ASCALIN_V0.9u(mod)-> Standard Error Output From FTOOL ascalin
ASCALIN_V0.9u(mod) : Detected gap > 15min in attitude file: 148479629.42616 ASCALIN_V0.9u(mod) : Detected gap > 15min in attitude file:-> Checking if ad45016000s100202m.unf is covered by attitude file
ASCALIN_V0.9u(mod)-> Standard Error Output From FTOOL ascalin
ASCALIN_V0.9u(mod) : Detected gap > 15min in attitude file: 148479629.42616 ASCALIN_V0.9u(mod) : Detected gap > 15min in attitude file:-> Checking if ad45016000s100212m.unf is covered by attitude file
ASCALIN_V0.9u(mod)-> Standard Error Output From FTOOL ascalin
ASCALIN_V0.9u(mod) : Detected gap > 15min in attitude file: 148479629.42616 ASCALIN_V0.9u(mod) : Detected gap > 15min in attitude file:-> Checking if ad45016000s100301l.unf is covered by attitude file
ASCALIN_V0.9u(mod)-> Standard Error Output From FTOOL ascalin
ASCALIN_V0.9u(mod) : Detected gap > 15min in attitude file: 148479629.42616 ASCALIN_V0.9u(mod) : Detected gap > 15min in attitude file:-> Checking if ad45016000s100302l.unf is covered by attitude file
ASCALIN_V0.9u(mod)-> Standard Error Output From FTOOL ascalin
ASCALIN_V0.9u(mod) : Detected gap > 15min in attitude file: 148479629.42616 ASCALIN_V0.9u(mod) : Detected gap > 15min in attitude file:-> Checking if ad45016000s100312l.unf is covered by attitude file
ASCALIN_V0.9u(mod)-> Standard Error Output From FTOOL ascalin
ASCALIN_V0.9u(mod) : Detected gap > 15min in attitude file: 148479629.42616 ASCALIN_V0.9u(mod) : Detected gap > 15min in attitude file:
S0-HK file: ft970915_1153_2050S0HK.fits
S1-HK file: ft970915_1153_2050S1HK.fits
G2-HK file: ft970915_1153_2050G2HK.fits
G3-HK file: ft970915_1153_2050G3HK.fits
Date and time are: 1997-09-15 11:52:01 mjd=50706.494461
Orbit file name is ./frf.orbit.241
Epoch of Orbital Elements: 1997-09-15 03:59:59
Rigidity Data File: ./rigidity.data.1.23
Attitude FRF: fa970915_1153.2050
output FITS File: ft970915_1153_2050.mkf
mkfilter2: Warning, faQparam error: time= 1.484779374315e+08 outside range of attitude file
Euler angles undefined for this bin
mkfilter2: Warning, faQparam error: time= 1.484779694315e+08 outside range of attitude file
Euler angles undefined for this bin
Total 3711 Data bins were processed.
-> Checking if column TIME in ft970915_1153_2050.mkf is in orderTime column is TIME ORDERED-> Calculating dead time values for filter file
The sum of the selected column is 5097.5127 The mean of the selected column is 26.970967 The standard deviation of the selected column is 44.639174 The minimum of selected column is 7.4687753 The maximum of selected column is 561.46619 The number of points used in calculation is 189-> Using the following selection criteria:
(SAA==0) &&(BR_EARTH>20) &&(ELV>10) &&(COR>6) &&(ACS==0) &&(ANG_DIST>0)&& (ANG_DIST<0.01) &&(FOV==0) && ( (S0_PIXL1>0 && S0_PIXL1<160.8 ) ) &&( (S0_SATF1<1) ||(S0_SATF1>1)) &&( (S0_SATF1<1) ||(S0_SATF1>1)) &&( (S0_SATF1<1) ||(S0_SATF1>1)) &&( (S0_SATF1<1) ||(S0_SATF1>1)) &&((T_DY_NT<0)||(T_DY_NT>16)) &&((T_SAA <0)||(T_SAA >16))-> Filtering ad45016000s000112h.unf into ad45016000s000112h.evt
The sum of the selected column is 5097.5127 The mean of the selected column is 26.970967 The standard deviation of the selected column is 44.639174 The minimum of selected column is 7.4687753 The maximum of selected column is 561.46619 The number of points used in calculation is 189-> Using the following selection criteria:
(SAA==0) &&(BR_EARTH>20) &&(ELV>10) &&(COR>6) &&(ACS==0) &&(ANG_DIST>0)&& (ANG_DIST<0.01) &&(FOV==0) && ( (S0_PIXL1>0 && S0_PIXL1<160.8 ) ) &&( (S0_SATF1<1) ||(S0_SATF1>1)) &&( (S0_SATF1<1) ||(S0_SATF1>1)) &&( (S0_SATF1<1) ||(S0_SATF1>1)) &&( (S0_SATF1<1) ||(S0_SATF1>1)) &&((T_DY_NT<0)||(T_DY_NT>16)) &&((T_SAA <0)||(T_SAA >16))-> Skipping ad45016000s000201m.unf because of mode
The sum of the selected column is 2101.9133 The mean of the selected column is 26.606497 The standard deviation of the selected column is 11.295525 The minimum of selected column is 8.4687786 The maximum of selected column is 74.281502 The number of points used in calculation is 79-> Using the following selection criteria:
(SAA==0) &&(BR_EARTH>20) &&(ELV>10) &&(COR>6) &&(ACS==0) &&(ANG_DIST>0)&& (ANG_DIST<0.01) &&(FOV==0) && ( (S0_PIXL1>0 && S0_PIXL1<60.4 ) ) &&( (S0_SATF1<1) ||(S0_SATF1>1)) &&( (S0_SATF1<1) ||(S0_SATF1>1)) &&( (S0_SATF1<1) ||(S0_SATF1>1)) &&( (S0_SATF1<1) ||(S0_SATF1>1)) &&((T_DY_NT<0)||(T_DY_NT>16)) &&((T_SAA <0)||(T_SAA >16))-> Filtering ad45016000s000212m.unf into ad45016000s000212m.evt
The sum of the selected column is 2101.9133 The mean of the selected column is 26.606497 The standard deviation of the selected column is 11.295525 The minimum of selected column is 8.4687786 The maximum of selected column is 74.281502 The number of points used in calculation is 79-> Using the following selection criteria:
(SAA==0) &&(BR_EARTH>20) &&(ELV>10) &&(COR>6) &&(ACS==0) &&(ANG_DIST>0)&& (ANG_DIST<0.01) &&(FOV==0) && ( (S0_PIXL1>0 && S0_PIXL1<60.4 ) ) &&( (S0_SATF1<1) ||(S0_SATF1>1)) &&( (S0_SATF1<1) ||(S0_SATF1>1)) &&( (S0_SATF1<1) ||(S0_SATF1>1)) &&( (S0_SATF1<1) ||(S0_SATF1>1)) &&((T_DY_NT<0)||(T_DY_NT>16)) &&((T_SAA <0)||(T_SAA >16))-> Skipping ad45016000s000301l.unf because of mode
(SAA==0) &&(BR_EARTH>20) &&(ELV>10) &&(COR>6) &&(ACS==0) &&(ANG_DIST>0)&& (ANG_DIST<0.01) &&(FOV==0) && ( (S0_PIXL1>0) )&&( (S0_SATF1<1) ||(S0_SATF1>1)) &&( (S0_SATF1<1) ||(S0_SATF1>1)) &&( (S0_SATF1<1) ||(S0_SATF1>1)) &&( (S0_SATF1<1) ||(S0_SATF1>1)) &&((T_DY_NT<0)||(T_DY_NT>16)) &&((T_SAA <0)||(T_SAA >16))-> Deleting ad45016000s000302l.evt since it contains 0 events
(SAA==0) &&(BR_EARTH>20) &&(ELV>10) &&(COR>6) &&(ACS==0) &&(ANG_DIST>0)&& (ANG_DIST<0.01) &&(FOV==0) && ( (S0_PIXL1>0) )&&( (S0_SATF1<1) ||(S0_SATF1>1)) &&( (S0_SATF1<1) ||(S0_SATF1>1)) &&( (S0_SATF1<1) ||(S0_SATF1>1)) &&( (S0_SATF1<1) ||(S0_SATF1>1)) &&((T_DY_NT<0)||(T_DY_NT>16)) &&((T_SAA <0)||(T_SAA >16))-> Deleting ad45016000s000312l.evt since it contains 0 events
The sum of the selected column is 7594.5458 The mean of the selected column is 40.396520 The standard deviation of the selected column is 70.984498 The minimum of selected column is 10.861148 The maximum of selected column is 963.71155 The number of points used in calculation is 188-> Using the following selection criteria:
(SAA==0) &&(BR_EARTH>20) &&(ELV>10) &&(COR>6) &&(ACS==0) &&(ANG_DIST>0)&& (ANG_DIST<0.01) &&(FOV==0) && ( (S1_PIXL3>0 && S1_PIXL3<253.3 ) ) &&( (S1_SATF3<1) ||(S1_SATF3>1)) &&( (S1_SATF3<1) ||(S1_SATF3>1)) &&( (S1_SATF3<1) ||(S1_SATF3>1)) &&( (S1_SATF3<1) ||(S1_SATF3>1)) &&((T_DY_NT<0)||(T_DY_NT>16)) &&((T_SAA <0)||(T_SAA >16))-> Filtering ad45016000s100112h.unf into ad45016000s100112h.evt
The sum of the selected column is 7594.5458 The mean of the selected column is 40.396520 The standard deviation of the selected column is 70.984498 The minimum of selected column is 10.861148 The maximum of selected column is 963.71155 The number of points used in calculation is 188-> Using the following selection criteria:
(SAA==0) &&(BR_EARTH>20) &&(ELV>10) &&(COR>6) &&(ACS==0) &&(ANG_DIST>0)&& (ANG_DIST<0.01) &&(FOV==0) && ( (S1_PIXL3>0 && S1_PIXL3<253.3 ) ) &&( (S1_SATF3<1) ||(S1_SATF3>1)) &&( (S1_SATF3<1) ||(S1_SATF3>1)) &&( (S1_SATF3<1) ||(S1_SATF3>1)) &&( (S1_SATF3<1) ||(S1_SATF3>1)) &&((T_DY_NT<0)||(T_DY_NT>16)) &&((T_SAA <0)||(T_SAA >16))-> Skipping ad45016000s100201m.unf because of mode
The sum of the selected column is 1976.0066 The mean of the selected column is 38.000126 The standard deviation of the selected column is 18.283794 The minimum of selected column is 15.781302 The maximum of selected column is 91.000298 The number of points used in calculation is 52-> Using the following selection criteria:
(SAA==0) &&(BR_EARTH>20) &&(ELV>10) &&(COR>6) &&(ACS==0) &&(ANG_DIST>0)&& (ANG_DIST<0.01) &&(FOV==0) && ( (S1_PIXL3>0 && S1_PIXL3<92.8 ) ) &&( (S1_SATF3<1) ||(S1_SATF3>1)) &&( (S1_SATF3<1) ||(S1_SATF3>1)) &&( (S1_SATF3<1) ||(S1_SATF3>1)) &&( (S1_SATF3<1) ||(S1_SATF3>1)) &&((T_DY_NT<0)||(T_DY_NT>16)) &&((T_SAA <0)||(T_SAA >16))-> Filtering ad45016000s100212m.unf into ad45016000s100212m.evt
The sum of the selected column is 1976.0066 The mean of the selected column is 38.000126 The standard deviation of the selected column is 18.283794 The minimum of selected column is 15.781302 The maximum of selected column is 91.000298 The number of points used in calculation is 52-> Using the following selection criteria:
(SAA==0) &&(BR_EARTH>20) &&(ELV>10) &&(COR>6) &&(ACS==0) &&(ANG_DIST>0)&& (ANG_DIST<0.01) &&(FOV==0) && ( (S1_PIXL3>0 && S1_PIXL3<92.8 ) ) &&( (S1_SATF3<1) ||(S1_SATF3>1)) &&( (S1_SATF3<1) ||(S1_SATF3>1)) &&( (S1_SATF3<1) ||(S1_SATF3>1)) &&( (S1_SATF3<1) ||(S1_SATF3>1)) &&((T_DY_NT<0)||(T_DY_NT>16)) &&((T_SAA <0)||(T_SAA >16))-> Skipping ad45016000s100301l.unf because of mode
(SAA==0) &&(BR_EARTH>20) &&(ELV>10) &&(COR>6) &&(ACS==0) &&(ANG_DIST>0)&& (ANG_DIST<0.01) &&(FOV==0) && ( (S1_PIXL3>0) )&&( (S1_SATF3<1) ||(S1_SATF3>1)) &&( (S1_SATF3<1) ||(S1_SATF3>1)) &&( (S1_SATF3<1) ||(S1_SATF3>1)) &&( (S1_SATF3<1) ||(S1_SATF3>1)) &&((T_DY_NT<0)||(T_DY_NT>16)) &&((T_SAA <0)||(T_SAA >16))-> Deleting ad45016000s100302l.evt since it contains 0 events
(SAA==0) &&(BR_EARTH>20) &&(ELV>10) &&(COR>6) &&(ACS==0) &&(ANG_DIST>0)&& (ANG_DIST<0.01) &&(FOV==0) && ( (S1_PIXL3>0) )&&( (S1_SATF3<1) ||(S1_SATF3>1)) &&( (S1_SATF3<1) ||(S1_SATF3>1)) &&( (S1_SATF3<1) ||(S1_SATF3>1)) &&( (S1_SATF3<1) ||(S1_SATF3>1)) &&((T_DY_NT<0)||(T_DY_NT>16)) &&((T_SAA <0)||(T_SAA >16))-> Deleting ad45016000s100312l.evt since it contains 0 events
(SAA==0)&& (COR>4)&& (G2_H0+G2_H2+G3_H0+G3_H2<45)&& (G2_H0+G2_H2+G3_H0+G3_H2<0.45*COR**2-13*COR+125)&& (RBM_CONT<100)&& (ELV>5)&& (ACS==0)&& (ANG_DIST>0)&& (ANG_DIST<0.01)&& (G2_L1>0)-> Filtering ad45016000g200270h.unf into ad45016000g200270h.evt
(SAA==0)&& (COR>4)&& (G2_H0+G2_H2+G3_H0+G3_H2<45)&& (G2_H0+G2_H2+G3_H0+G3_H2<0.45*COR**2-13*COR+125)&& (RBM_CONT<100)&& (ELV>5)&& (ACS==0)&& (ANG_DIST>0)&& (ANG_DIST<0.01)&& (G2_L1>0)-> Filtering ad45016000g200370l.unf into ad45016000g200370l.evt
(SAA==0)&& (COR>4)&& (G2_H0+G2_H2+G3_H0+G3_H2<45)&& (G2_H0+G2_H2+G3_H0+G3_H2<0.45*COR**2-13*COR+125)&& (RBM_CONT<100)&& (ELV>5)&& (ACS==0)&& (ANG_DIST>0)&& (ANG_DIST<0.01)&& (G2_L1>0)-> Filtering ad45016000g300170m.unf into ad45016000g300170m.evt
(SAA==0)&& (COR>4)&& (G2_H0+G2_H2+G3_H0+G3_H2<45)&& (G2_H0+G2_H2+G3_H0+G3_H2<0.45*COR**2-13*COR+125)&& (RBM_CONT<100)&& (ELV>5)&& (ACS==0)&& (ANG_DIST>0)&& (ANG_DIST<0.01)&& (G3_L1>0)-> Filtering ad45016000g300270h.unf into ad45016000g300270h.evt
(SAA==0)&& (COR>4)&& (G2_H0+G2_H2+G3_H0+G3_H2<45)&& (G2_H0+G2_H2+G3_H0+G3_H2<0.45*COR**2-13*COR+125)&& (RBM_CONT<100)&& (ELV>5)&& (ACS==0)&& (ANG_DIST>0)&& (ANG_DIST<0.01)&& (G3_L1>0)-> Filtering ad45016000g300370l.unf into ad45016000g300370l.evt
(SAA==0)&& (COR>4)&& (G2_H0+G2_H2+G3_H0+G3_H2<45)&& (G2_H0+G2_H2+G3_H0+G3_H2<0.45*COR**2-13*COR+125)&& (RBM_CONT<100)&& (ELV>5)&& (ACS==0)&& (ANG_DIST>0)&& (ANG_DIST<0.01)&& (G3_L1>0)
-ANNULUS(128.5,128.5,192,88) -ELLIPSE(167.5,220,24.66,28.95,245.298)-> gis2_ano_on_flf_180295.fits already present in current directory
ASCAEXPO_V0.9b
reading data file: ad45016000g200170m.evt
reading gti ext: STDGTI
reading cal file: gis2_ano_on_flf_180295.fits
reading inst file: GIS2_REGION256.4_regionmap.tmp
making an inst map...
rebin gis: 1
multiply inst map...
reading att file: ./fa970915_1153.2050
making an exposure map...
Aspect RA/DEC/ROLL : 267.2290 -27.4855 82.2258
Mean RA/DEC/ROLL : 267.2381 -27.4667 82.2258
Pnt RA/DEC/ROLL : 267.2847 -27.4827 82.2258
Image rebin factor : 1
Attitude Records : 21358
GTI intervals : 10
Total GTI (secs) : 2319.997
Max attitude excursion (arcsecs) : 5.000
0 Percent Complete: Total/live time: 0.00 0.00
10 Percent Complete: Total/live time: 336.01 336.01
20 Percent Complete: Total/live time: 607.99 607.99
30 Percent Complete: Total/live time: 943.97 943.97
40 Percent Complete: Total/live time: 960.00 960.00
50 Percent Complete: Total/live time: 1184.01 1184.01
60 Percent Complete: Total/live time: 1776.07 1776.07
70 Percent Complete: Total/live time: 1776.07 1776.07
80 Percent Complete: Total/live time: 2320.00 2320.00
100 Percent Complete: Total/live time: 2320.00 2320.00
Number of attitude steps used: 16
Number of attitude steps avail: 7214
Mean RA/DEC pixel offset: -9.7176 -3.3699
writing expo file: ad45016000g200170m.expo
closing attitude file...
closing data file...
-> Generating low and high energy images for ad45016000g200170m.evt
ASCAEXPO_V0.9b
reading data file: ad45016000g200270h.evt
reading gti ext: STDGTI
reading cal file: gis2_ano_on_flf_180295.fits
reading inst file: GIS2_REGION256.4_regionmap.tmp
making an inst map...
rebin gis: 1
multiply inst map...
reading att file: ./fa970915_1153.2050
making an exposure map...
Aspect RA/DEC/ROLL : 267.2290 -27.4855 82.2256
Mean RA/DEC/ROLL : 267.2425 -27.4660 82.2256
Pnt RA/DEC/ROLL : 267.2096 -27.5036 82.2256
Image rebin factor : 1
Attitude Records : 21358
GTI intervals : 11
Total GTI (secs) : 5268.169
Max attitude excursion (arcsecs) : 5.000
0 Percent Complete: Total/live time: 0.00 0.00
10 Percent Complete: Total/live time: 1300.00 1300.00
20 Percent Complete: Total/live time: 1300.00 1300.00
30 Percent Complete: Total/live time: 1694.02 1694.02
40 Percent Complete: Total/live time: 2672.01 2672.01
50 Percent Complete: Total/live time: 3044.01 3044.01
60 Percent Complete: Total/live time: 3434.00 3434.00
70 Percent Complete: Total/live time: 4028.08 4028.08
80 Percent Complete: Total/live time: 4379.08 4379.08
90 Percent Complete: Total/live time: 4802.07 4802.07
100 Percent Complete: Total/live time: 5268.17 5268.17
Number of attitude steps used: 15
Number of attitude steps avail: 12476
Mean RA/DEC pixel offset: -9.6197 -3.6092
writing expo file: ad45016000g200270h.expo
closing attitude file...
closing data file...
-> Generating low and high energy images for ad45016000g200270h.evt
ASCAEXPO_V0.9b
reading data file: ad45016000g200370l.evt
reading gti ext: STDGTI
reading cal file: gis2_ano_on_flf_180295.fits
reading inst file: GIS2_REGION256.4_regionmap.tmp
making an inst map...
rebin gis: 1
multiply inst map...
reading att file: ./fa970915_1153.2050
making an exposure map...
Aspect RA/DEC/ROLL : 267.2290 -27.4855 82.2254
Mean RA/DEC/ROLL : 267.2418 -27.4658 82.2254
Pnt RA/DEC/ROLL : 267.2229 -27.5029 82.2254
Image rebin factor : 1
Attitude Records : 21358
GTI intervals : 1
Total GTI (secs) : 63.914
Max attitude excursion (arcsecs) : 5.000
0 Percent Complete: Total/live time: 0.00 0.00
10 Percent Complete: Total/live time: 11.91 11.91
20 Percent Complete: Total/live time: 63.91 63.91
100 Percent Complete: Total/live time: 63.91 63.91
Number of attitude steps used: 2
Number of attitude steps avail: 170
Mean RA/DEC pixel offset: -5.1382 -2.2095
writing expo file: ad45016000g200370l.expo
closing attitude file...
closing data file...
-> Generating low and high energy images for ad45016000g200370l.evt-ANNULUS(128.5,128.5,192,88) -ELLIPSE(217,95,21.56,25.92,169.216)-> gis3_ano_on_flf_180295.fits already present in current directory
ASCAEXPO_V0.9b
reading data file: ad45016000g300170m.evt
reading gti ext: STDGTI
reading cal file: gis3_ano_on_flf_180295.fits
reading inst file: GIS3_REGION256.4_regionmap.tmp
making an inst map...
rebin gis: 1
multiply inst map...
reading att file: ./fa970915_1153.2050
making an exposure map...
Aspect RA/DEC/ROLL : 267.2290 -27.4855 82.2289
Mean RA/DEC/ROLL : 267.2315 -27.4908 82.2289
Pnt RA/DEC/ROLL : 267.2912 -27.4586 82.2289
Image rebin factor : 1
Attitude Records : 21358
GTI intervals : 10
Total GTI (secs) : 2319.997
Max attitude excursion (arcsecs) : 5.000
0 Percent Complete: Total/live time: 0.00 0.00
10 Percent Complete: Total/live time: 336.01 336.01
20 Percent Complete: Total/live time: 607.99 607.99
30 Percent Complete: Total/live time: 943.97 943.97
40 Percent Complete: Total/live time: 960.00 960.00
50 Percent Complete: Total/live time: 1184.01 1184.01
60 Percent Complete: Total/live time: 1776.07 1776.07
70 Percent Complete: Total/live time: 1776.07 1776.07
80 Percent Complete: Total/live time: 2320.00 2320.00
100 Percent Complete: Total/live time: 2320.00 2320.00
Number of attitude steps used: 16
Number of attitude steps avail: 7214
Mean RA/DEC pixel offset: 1.6062 -2.2450
writing expo file: ad45016000g300170m.expo
closing attitude file...
closing data file...
-> Generating low and high energy images for ad45016000g300170m.evt
ASCAEXPO_V0.9b
reading data file: ad45016000g300270h.evt
reading gti ext: STDGTI
reading cal file: gis3_ano_on_flf_180295.fits
reading inst file: GIS3_REGION256.4_regionmap.tmp
making an inst map...
rebin gis: 1
multiply inst map...
reading att file: ./fa970915_1153.2050
making an exposure map...
Aspect RA/DEC/ROLL : 267.2290 -27.4855 82.2287
Mean RA/DEC/ROLL : 267.2359 -27.4902 82.2287
Pnt RA/DEC/ROLL : 267.2161 -27.4794 82.2287
Image rebin factor : 1
Attitude Records : 21358
GTI intervals : 11
Total GTI (secs) : 5264.169
Max attitude excursion (arcsecs) : 5.000
0 Percent Complete: Total/live time: 0.00 0.00
10 Percent Complete: Total/live time: 1300.00 1300.00
20 Percent Complete: Total/live time: 1300.00 1300.00
30 Percent Complete: Total/live time: 1694.02 1694.02
40 Percent Complete: Total/live time: 2672.01 2672.01
50 Percent Complete: Total/live time: 3044.01 3044.01
60 Percent Complete: Total/live time: 3434.00 3434.00
70 Percent Complete: Total/live time: 4026.08 4026.08
80 Percent Complete: Total/live time: 4377.08 4377.08
90 Percent Complete: Total/live time: 4800.07 4800.07
100 Percent Complete: Total/live time: 5264.17 5264.17
Number of attitude steps used: 15
Number of attitude steps avail: 12467
Mean RA/DEC pixel offset: 1.6538 -2.4893
writing expo file: ad45016000g300270h.expo
closing attitude file...
closing data file...
-> Generating low and high energy images for ad45016000g300270h.evt
ASCAEXPO_V0.9b
reading data file: ad45016000g300370l.evt
reading gti ext: STDGTI
reading cal file: gis3_ano_on_flf_180295.fits
reading inst file: GIS3_REGION256.4_regionmap.tmp
making an inst map...
rebin gis: 1
multiply inst map...
reading att file: ./fa970915_1153.2050
making an exposure map...
Aspect RA/DEC/ROLL : 267.2290 -27.4855 82.2284
Mean RA/DEC/ROLL : 267.2353 -27.4900 82.2284
Pnt RA/DEC/ROLL : 267.2295 -27.4787 82.2284
Image rebin factor : 1
Attitude Records : 21358
GTI intervals : 1
Total GTI (secs) : 63.914
Max attitude excursion (arcsecs) : 5.000
0 Percent Complete: Total/live time: 0.00 0.00
10 Percent Complete: Total/live time: 11.91 11.91
20 Percent Complete: Total/live time: 63.91 63.91
100 Percent Complete: Total/live time: 63.91 63.91
Number of attitude steps used: 2
Number of attitude steps avail: 170
Mean RA/DEC pixel offset: 0.9011 -1.6095
writing expo file: ad45016000g300370l.expo
closing attitude file...
closing data file...
-> Generating low and high energy images for ad45016000g300370l.evt
ASCAEXPO_V0.9b
reading data file: ad45016000s000102h.evt
reading gti ext: STDGTI
reading hp ext: HOT_PIXELS
reading cal file: s0_teldef_ascalin.fits
making an inst map...
SIS AREA DISC ENABL OFF
CHIP: 0 1 2 3
CCD POWER ON/OFF: OFF ON OFF OFF
AREA DISC IN/OUT: OUT OUT IN IN
AREA DISC H START: 6 6 6 316
AREA DISC H STOP: 425 425 200 425
AREA DISC V START: 2 2 2 2
AREA DISC V STOP: 422 422 150 112
reading att file: ./fa970915_1153.2050
making an exposure map...
Aspect RA/DEC/ROLL : 267.2290 -27.4855 82.2196
Mean RA/DEC/ROLL : 267.2545 -27.4798 82.2196
Pnt RA/DEC/ROLL : 267.1958 -27.4893 82.2196
Image rebin factor : 4
Attitude Records : 21358
Hot Pixels : 8
GTI intervals : 10
Total GTI (secs) : 6004.125
Max attitude excursion (arcsecs) : 5.000
0 Percent Complete: Total/live time: 0.00 0.00
10 Percent Complete: Total/live time: 1308.00 1308.00
20 Percent Complete: Total/live time: 1308.00 1308.00
30 Percent Complete: Total/live time: 2644.14 2644.14
40 Percent Complete: Total/live time: 2644.14 2644.14
50 Percent Complete: Total/live time: 3380.13 3380.13
60 Percent Complete: Total/live time: 3924.13 3924.13
70 Percent Complete: Total/live time: 4628.13 4628.13
80 Percent Complete: Total/live time: 5172.13 5172.13
90 Percent Complete: Total/live time: 6004.13 6004.13
100 Percent Complete: Total/live time: 6004.13 6004.13
Number of attitude steps used: 16
Number of attitude steps avail: 14076
Mean RA/DEC pixel offset: -38.9367 -109.2112
writing expo file: ad45016000s000102h.expo
closing attitude file...
closing data file...
-> Generating low and high energy images for ad45016000s000102h.evt
ASCAEXPO_V0.9b
reading data file: ad45016000s000202m.evt
reading gti ext: STDGTI
reading hp ext: HOT_PIXELS
reading cal file: s0_teldef_ascalin.fits
making an inst map...
SIS AREA DISC ENABL OFF
CHIP: 0 1 2 3
CCD POWER ON/OFF: OFF ON OFF OFF
AREA DISC IN/OUT: OUT OUT IN IN
AREA DISC H START: 6 6 6 316
AREA DISC H STOP: 425 425 200 425
AREA DISC V START: 2 2 2 2
AREA DISC V STOP: 422 422 150 112
reading att file: ./fa970915_1153.2050
making an exposure map...
Aspect RA/DEC/ROLL : 267.2290 -27.4855 82.2195
Mean RA/DEC/ROLL : 267.2528 -27.4806 82.2195
Pnt RA/DEC/ROLL : 267.2709 -27.4685 82.2195
Image rebin factor : 4
Attitude Records : 21358
Hot Pixels : 6
GTI intervals : 14
Total GTI (secs) : 2567.875
Max attitude excursion (arcsecs) : 5.000
0 Percent Complete: Total/live time: 0.00 0.00
10 Percent Complete: Total/live time: 487.86 487.86
20 Percent Complete: Total/live time: 679.83 679.83
30 Percent Complete: Total/live time: 1031.86 1031.86
40 Percent Complete: Total/live time: 1167.70 1167.70
50 Percent Complete: Total/live time: 1447.88 1447.88
60 Percent Complete: Total/live time: 1991.88 1991.88
70 Percent Complete: Total/live time: 1991.88 1991.88
80 Percent Complete: Total/live time: 2567.88 2567.88
100 Percent Complete: Total/live time: 2567.88 2567.88
Number of attitude steps used: 17
Number of attitude steps avail: 6947
Mean RA/DEC pixel offset: -37.1007 -92.8120
writing expo file: ad45016000s000202m.expo
closing attitude file...
closing data file...
-> Generating low and high energy images for ad45016000s000202m.evt
ASCAEXPO_V0.9b
reading data file: ad45016000s100102h.evt
reading gti ext: STDGTI
reading hp ext: HOT_PIXELS
reading cal file: s1_teldef_ascalin.fits
making an inst map...
SIS AREA DISC ENABL OFF
CHIP: 0 1 2 3
CCD POWER ON/OFF: OFF OFF OFF ON
AREA DISC IN/OUT: OUT OUT OUT OUT
AREA DISC H START: 6 6 6 6
AREA DISC H STOP: 425 425 425 425
AREA DISC V START: 2 2 2 2
AREA DISC V STOP: 422 422 422 422
reading att file: ./fa970915_1153.2050
making an exposure map...
Aspect RA/DEC/ROLL : 267.2290 -27.4855 82.2277
Mean RA/DEC/ROLL : 267.2365 -27.4766 82.2277
Pnt RA/DEC/ROLL : 267.2134 -27.4924 82.2277
Image rebin factor : 4
Attitude Records : 21358
Hot Pixels : 15
GTI intervals : 10
Total GTI (secs) : 6024.345
Max attitude excursion (arcsecs) : 5.000
0 Percent Complete: Total/live time: 0.00 0.00
10 Percent Complete: Total/live time: 1304.00 1304.00
20 Percent Complete: Total/live time: 1304.00 1304.00
30 Percent Complete: Total/live time: 2640.14 2640.14
40 Percent Complete: Total/live time: 2640.14 2640.14
50 Percent Complete: Total/live time: 3376.13 3376.13
60 Percent Complete: Total/live time: 3920.13 3920.13
70 Percent Complete: Total/live time: 4624.13 4624.13
80 Percent Complete: Total/live time: 5192.35 5192.35
90 Percent Complete: Total/live time: 6024.35 6024.35
100 Percent Complete: Total/live time: 6024.35 6024.35
Number of attitude steps used: 16
Number of attitude steps avail: 14118
Mean RA/DEC pixel offset: -43.3810 -37.3601
writing expo file: ad45016000s100102h.expo
closing attitude file...
closing data file...
-> Generating low and high energy images for ad45016000s100102h.evt
ASCAEXPO_V0.9b
reading data file: ad45016000s100202m.evt
reading gti ext: STDGTI
reading hp ext: HOT_PIXELS
reading cal file: s1_teldef_ascalin.fits
making an inst map...
SIS AREA DISC ENABL OFF
CHIP: 0 1 2 3
CCD POWER ON/OFF: OFF OFF OFF ON
AREA DISC IN/OUT: OUT OUT OUT OUT
AREA DISC H START: 6 6 6 6
AREA DISC H STOP: 425 425 425 425
AREA DISC V START: 2 2 2 2
AREA DISC V STOP: 422 422 422 422
reading att file: ./fa970915_1153.2050
making an exposure map...
Aspect RA/DEC/ROLL : 267.2290 -27.4855 82.2276
Mean RA/DEC/ROLL : 267.2351 -27.4775 82.2276
Pnt RA/DEC/ROLL : 267.2885 -27.4716 82.2276
Image rebin factor : 4
Attitude Records : 21358
Hot Pixels : 12
GTI intervals : 23
Total GTI (secs) : 1711.655
Max attitude excursion (arcsecs) : 5.000
0 Percent Complete: Total/live time: 0.00 0.00
10 Percent Complete: Total/live time: 192.00 192.00
20 Percent Complete: Total/live time: 487.83 487.83
30 Percent Complete: Total/live time: 615.86 615.86
40 Percent Complete: Total/live time: 719.70 719.70
50 Percent Complete: Total/live time: 1191.88 1191.88
60 Percent Complete: Total/live time: 1191.88 1191.88
70 Percent Complete: Total/live time: 1231.81 1231.81
80 Percent Complete: Total/live time: 1703.88 1703.88
90 Percent Complete: Total/live time: 1703.88 1703.88
100 Percent Complete: Total/live time: 1711.65 1711.65
Number of attitude steps used: 16
Number of attitude steps avail: 7806
Mean RA/DEC pixel offset: -41.3078 -24.1830
writing expo file: ad45016000s100202m.expo
closing attitude file...
closing data file...
-> Generating low and high energy images for ad45016000s100202m.evtad45016000s000102h.expo ad45016000s000202m.expo ad45016000s100102h.expo ad45016000s100202m.expo-> Summing the following images to produce ad45016000sis32002_all.totsky
ad45016000s000102h.img ad45016000s000202m.img ad45016000s100102h.img ad45016000s100202m.img-> Summing the following images to produce ad45016000sis32002_lo.totsky
ad45016000s000102h_lo.img ad45016000s000202m_lo.img ad45016000s100102h_lo.img ad45016000s100202m_lo.img-> Summing the following images to produce ad45016000sis32002_hi.totsky
ad45016000s000102h_hi.img ad45016000s000202m_hi.img ad45016000s100102h_hi.img ad45016000s100202m_hi.img-> Running XIMAGE to create ad45016000sis32002.gif
No of detectors read in: 20 ![1]XIMAGE> read/fits ad45016000sis32002_all.totsky Reading an image Telescope ASCA SIS0 Image display size = 320 Done, closing file Largest, Smallest 6.00000 0. Bscale, Bzero from file 1.0000000000000 0. After internal scaling Bscale and Bzero 1.0000000000000 0. Image level, max: 6 min: 0 ![2]XIMAGE> read/exp_map ad45016000sis32002.totexpo Reading an image Telescope ASCA SIS0 Image display size = 320 Done, closing file Largest, Smallest 271.800 0. Bscale, Bzero from file 1.0000000000000 0. After internal scaling Bscale and Bzero 1.0000000000000 0. Image level, max: 271 min: 0 ![3]XIMAGE> smooth ![4]XIMAGE> cpd /ppm ![5]XIMAGE> cey 2000 ![6]XIMAGE> title "AGPS267.3-27.4" ![7]XIMAGE> title/lower "ASCA SIS0,SIS1 September 15, 1997 Exposure: 16307.9 s" ![8]XIMAGE> disp/correct/noframe Displaying image The image is exposure corrected Min = 0 max = 32767 ![9]XIMAGE> grid ![10]XIMAGE> scale scal_f, min_inten 1.00000 0. i,inten,mm,pp 1 0. 0 0 i,inten,mm,pp 2 4.00000 40 -1 i,inten,mm,pp 3 8.00000 80 -1 i,inten,mm,pp 4 14.0000 14 0 ![11]XIMAGE> exit-> Summing gis images
ad45016000g200170m.expo ad45016000g200270h.expo ad45016000g200370l.expo ad45016000g300170m.expo ad45016000g300270h.expo ad45016000g300370l.expo-> Summing the following images to produce ad45016000gis25670_all.totsky
ad45016000g200170m.img ad45016000g200270h.img ad45016000g200370l.img ad45016000g300170m.img ad45016000g300270h.img ad45016000g300370l.img-> Summing the following images to produce ad45016000gis25670_lo.totsky
ad45016000g200170m_lo.img ad45016000g200270h_lo.img ad45016000g200370l_lo.img ad45016000g300170m_lo.img ad45016000g300270h_lo.img ad45016000g300370l_lo.img-> Summing the following images to produce ad45016000gis25670_hi.totsky
ad45016000g200170m_hi.img ad45016000g200270h_hi.img ad45016000g200370l_hi.img ad45016000g300170m_hi.img ad45016000g300270h_hi.img ad45016000g300370l_hi.img-> Running XIMAGE to create ad45016000gis25670.gif
No of detectors read in: 20 ![1]XIMAGE> read/fits ad45016000gis25670_all.totsky Reading an image Telescope ASCA GIS2 Image display size = 256 Done, closing file Largest, Smallest 17.0000 0. Bscale, Bzero from file 1.0000000000000 0. After internal scaling Bscale and Bzero 1.0000000000000 0. Image level, max: 17 min: 0 ![2]XIMAGE> read/exp_map ad45016000gis25670.totexpo Reading an image Telescope ASCA GIS2 Image display size = 256 Done, closing file Largest, Smallest 255.003 0. Bscale, Bzero from file 1.0000000000000 0. After internal scaling Bscale and Bzero 1.0000000000000 0. Image level, max: 255 min: 0 ![3]XIMAGE> smooth ![4]XIMAGE> cpd /ppm ![5]XIMAGE> cey 2000 ![6]XIMAGE> title "AGPS267.3-27.4" ![7]XIMAGE> title/lower "ASCA GIS2,GIS3 September 15, 1997 Exposure: 15300.1 s" ![8]XIMAGE> disp/correct/noframe Displaying image The image is exposure corrected Min = 0 max = 32767 ![9]XIMAGE> grid ![10]XIMAGE> scale scal_f, min_inten 1.00000 0. i,inten,mm,pp 1 0. 0 0 i,inten,mm,pp 2 4.00000 40 -1 i,inten,mm,pp 3 11.0000 11 0 i,inten,mm,pp 4 18.0000 18 0 ![11]XIMAGE> exit
91 207 0.000793493 7 8 14.7745 131 213 0.000740927 33 34 12.235-> Smoothing ad45016000gis25670_hi.totsky with ad45016000gis25670.totexpo
91 207 0.000615845 6 7 23.089 119 216 0.000568581 23 24 20.1724-> Smoothing ad45016000gis25670_lo.totsky with ad45016000gis25670.totexpo
132 215 0.000222978 178 62 10.0583-> Determining extraction radii
91 207 7 F 131 213 33 T-> Sources with radius >= 2
91 207 7 F 131 213 33 T-> Standard Output From STOOL colorpic:
color plane 0 color plane 1 color plane 2 writing image image written-> Creating fits catalog of sources: ad45016000gis25670.src
131 249 8.50966e-05 32 28 4.42006 125 193 8.13511e-05 23 8 4.75807-> Smoothing ad45016000sis32002_hi.totsky with ad45016000sis32002.totexpo
125 193 7.25902e-05 19 8 5.19562 131 249 6.88281e-05 31 32 5.43714-> Smoothing ad45016000sis32002_lo.totsky with ad45016000sis32002.totexpo
131 249 32 T 125 193 23 F-> Sources with radius >= 2
131 249 32 T 125 193 23 F-> Standard Output From STOOL colorpic:
color plane 0 color plane 1 color plane 2 writing image image written-> Creating fits catalog of sources: ad45016000sis32002.src
The sum of the selected column is 37154.000 The mean of the selected column is 254.47945 The standard deviation of the selected column is 15.910621 The minimum of selected column is 224.00000 The maximum of selected column is 286.00000 The number of points used in calculation is 146-> Standard Output From FTOOL fstatistic:
The sum of the selected column is 76020.000 The mean of the selected column is 520.68493 The standard deviation of the selected column is 18.243848 The minimum of selected column is 480.00000 The maximum of selected column is 557.00000 The number of points used in calculation is 146-> Converting (500.0,772.0,2.0) to s0 detector coordinates
The sum of the selected column is 25441.000 The mean of the selected column is 471.12963 The standard deviation of the selected column is 9.3264612 The minimum of selected column is 449.00000 The maximum of selected column is 491.00000 The number of points used in calculation is 54-> Standard Output From FTOOL fstatistic:
The sum of the selected column is 25192.000 The mean of the selected column is 466.51852 The standard deviation of the selected column is 13.804211 The minimum of selected column is 433.00000 The maximum of selected column is 487.00000 The number of points used in calculation is 54-> Converting (524.0,996.0,2.0) to s1 detector coordinates
The sum of the selected column is 19631.000 The mean of the selected column is 251.67949 The standard deviation of the selected column is 15.809329 The minimum of selected column is 222.00000 The maximum of selected column is 280.00000 The number of points used in calculation is 78-> Standard Output From FTOOL fstatistic:
The sum of the selected column is 43458.000 The mean of the selected column is 557.15385 The standard deviation of the selected column is 17.353526 The minimum of selected column is 523.00000 The maximum of selected column is 591.00000 The number of points used in calculation is 78-> Converting (500.0,772.0,2.0) to s1 detector coordinates
The sum of the selected column is 17910.000 The mean of the selected column is 471.31579 The standard deviation of the selected column is 11.167291 The minimum of selected column is 447.00000 The maximum of selected column is 489.00000 The number of points used in calculation is 38-> Standard Output From FTOOL fstatistic:
The sum of the selected column is 19173.000 The mean of the selected column is 504.55263 The standard deviation of the selected column is 14.518762 The minimum of selected column is 470.00000 The maximum of selected column is 532.00000 The number of points used in calculation is 38-> Converting (91.0,207.0,2.0) to g2 detector coordinates
The sum of the selected column is 1219.0000 The mean of the selected column is 46.884615 The standard deviation of the selected column is 1.2434443 The minimum of selected column is 45.000000 The maximum of selected column is 49.000000 The number of points used in calculation is 26-> Standard Output From FTOOL fstatistic:
The sum of the selected column is 2604.0000 The mean of the selected column is 100.15385 The standard deviation of the selected column is 2.2572959 The minimum of selected column is 97.000000 The maximum of selected column is 105.00000 The number of points used in calculation is 26-> Converting (131.0,213.0,2.0) to g2 detector coordinates
The sum of the selected column is 462.00000 The mean of the selected column is 42.000000 The standard deviation of the selected column is 0.44721360 The minimum of selected column is 41.000000 The maximum of selected column is 43.000000 The number of points used in calculation is 11-> Standard Output From FTOOL fstatistic:
The sum of the selected column is 1535.0000 The mean of the selected column is 139.54545 The standard deviation of the selected column is 1.2933396 The minimum of selected column is 138.00000 The maximum of selected column is 142.00000 The number of points used in calculation is 11-> Converting (91.0,207.0,2.0) to g3 detector coordinates
The sum of the selected column is 1955.0000 The mean of the selected column is 47.682927 The standard deviation of the selected column is 1.1713032 The minimum of selected column is 46.000000 The maximum of selected column is 50.000000 The number of points used in calculation is 41-> Standard Output From FTOOL fstatistic:
The sum of the selected column is 4125.0000 The mean of the selected column is 100.60976 The standard deviation of the selected column is 1.3015001 The minimum of selected column is 97.000000 The maximum of selected column is 103.00000 The number of points used in calculation is 41-> Converting (131.0,213.0,2.0) to g3 detector coordinates
The sum of the selected column is 3007.0000 The mean of the selected column is 46.984375 The standard deviation of the selected column is 1.1750338 The minimum of selected column is 45.000000 The maximum of selected column is 50.000000 The number of points used in calculation is 64-> Standard Output From FTOOL fstatistic:
The sum of the selected column is 8994.0000 The mean of the selected column is 140.53125 The standard deviation of the selected column is 1.3682192 The minimum of selected column is 138.00000 The maximum of selected column is 143.00000 The number of points used in calculation is 64
1 ad45016000s000102h.evt 3011 1 ad45016000s000202m.evt 3011-> Fetching SIS0_NOTCHIP0.1
ad45016000s000102h.evt ad45016000s000202m.evt-> Grouping ad45016000s010102_1.pi to 40 counts/bin
------------------------- MANDATORY KEYWORDS/VALUES ------------------------- -------------------------------------------------------------------- -------------------------------------------------------------------- EXTNAME - SPECTRUM Name of this BINTABLE TELESCOP - ASCA Mission/Satellite name INSTRUME - SIS0 Instrument/Detector FILTER - NONE Instrument filter in use EXPOSURE - 8572.0 Integration time (in secs) of PHA data AREASCAL - 1.0000 Area scaling factor BACKSCAL - 1.99219E-02 Background scaling factor BACKFILE - NONE Associated background file CORRSCAL - 1.0000 Correlation scaling factor CORRFILE - none Associated correlation file RESPFILE - NONE Associated redistribution matrix file ANCRFILE - none Associated ancillary response file XFLT0001 - none XSPEC selection filter POISSERR - TRUE Whether Poissonian errors apply CHANTYPE - PI Whether channels have been corrected TLMIN1 - 0 First legal Detector channel DETCHANS - 512 No. of legal detector channels NCHAN - 512 No. of detector channels in dataset PHAVERSN - 1.1.0 OGIP FITS version number STAT_ERR - FALSE Statistical Error SYS_ERR - TRUE Fractional Systematic Error QUALITY - TRUE Quality Flag GROUPING - FALSE Grouping Flag -------------------------------------------------------------------- -------------------------------------------------------------------- ... ... -------- ... GROUPING ... -------- ... --------------------------------------------- ... Channel Grouping (Channel-Channel) : ... 0 - 16 of undefined grouping (Channel quality=bad) ... 17 - 41 are grouped by a factor 25 ... 42 - 49 are grouped by a factor 8 ... 50 - 61 are grouped by a factor 6 ... 62 - 66 are grouped by a factor 5 ... 67 - 73 are grouped by a factor 7 ... 74 - 82 are grouped by a factor 9 ... 83 - 96 are grouped by a factor 7 ... 97 - 105 are grouped by a factor 9 ... 106 - 112 are grouped by a factor 7 ... 113 - 117 are grouped by a factor 5 ... 118 - 124 are grouped by a factor 7 ... 125 - 142 are grouped by a factor 9 ... 143 - 150 are grouped by a factor 8 ... 151 - 168 are grouped by a factor 18 ... 169 - 188 are grouped by a factor 20 ... 189 - 221 are grouped by a factor 33 ... 222 - 511 of undefined grouping (Channel quality=bad) ... --------------------------------------------- ... ...... exiting, changes written to file : ad45016000s010102_1.pi ** grppha 2.8.1 completed successfully-> Source occupies chip(s) 1
Sisrmg Version 1.1, Configured 04/97 This version resolves *all* known keyword incompatibilities with other FTOOLS tasks. If you have previously fudged *any* keywords in the PHA file to compensate, incorrect results will follow. Setting 1st PHA channel to 0 Making v1.1 1180x512 S0C1 Bright PI RMF Calibration data files: ecd = ./sis0c1p40_290296.fits cti = ./sisph2pi_110397.fits echo = ./sisechos_290296.fits rdd = ./sisrddis_290296.fits Please stand by... ...Done.-> Generating ad45016000s010102_1.arf with point=no
ASCAARF vers 2.81 28 Aug 1998.
Input WMAP array has size 20 by 29 bins
expanded to 20 by 29 bins
First WMAP bin is at detector pixel 224 392
8 detector pixels per WMAP bin
WMAP bin size is 0.21600 mm
0.21216 arcmin
Selected region size is 1.4348 arcmin^2
Optical axis is detector pixel 662.72 559.02
1180 energies from RMF file
Effective area fudge applied
Arf filter applied
Total counts in region = 8.47000E+02
Weighted mean angle from optical axis = 10.073 arcmin
-> Extracting ad45016000s010102_2.pi from ad45016000s032002_2.reg and:ad45016000s000102h.evt ad45016000s000202m.evt-> Deleting ad45016000s010102_2.pi since it has 479 events
1 ad45016000s000112h.evt 3088 1 ad45016000s000212m.evt 3088-> SIS0_NOTCHIP0.1 already present in current directory
ad45016000s000112h.evt ad45016000s000212m.evt-> Grouping ad45016000s010212_1.pi to 40 counts/bin
------------------------- MANDATORY KEYWORDS/VALUES ------------------------- -------------------------------------------------------------------- -------------------------------------------------------------------- EXTNAME - SPECTRUM Name of this BINTABLE TELESCOP - ASCA Mission/Satellite name INSTRUME - SIS0 Instrument/Detector FILTER - NONE Instrument filter in use EXPOSURE - 8572.0 Integration time (in secs) of PHA data AREASCAL - 1.0000 Area scaling factor BACKSCAL - 1.99219E-02 Background scaling factor BACKFILE - NONE Associated background file CORRSCAL - 1.0000 Correlation scaling factor CORRFILE - none Associated correlation file RESPFILE - NONE Associated redistribution matrix file ANCRFILE - none Associated ancillary response file XFLT0001 - none XSPEC selection filter POISSERR - TRUE Whether Poissonian errors apply CHANTYPE - PI Whether channels have been corrected TLMIN1 - 0 First legal Detector channel DETCHANS - 1024 No. of legal detector channels NCHAN - 1024 No. of detector channels in dataset PHAVERSN - 1.1.0 OGIP FITS version number STAT_ERR - FALSE Statistical Error SYS_ERR - TRUE Fractional Systematic Error QUALITY - TRUE Quality Flag GROUPING - FALSE Grouping Flag -------------------------------------------------------------------- -------------------------------------------------------------------- ... ... -------- ... GROUPING ... -------- ... --------------------------------------------- ... Channel Grouping (Channel-Channel) : ... 0 - 31 of undefined grouping (Channel quality=bad) ... 32 - 83 are grouped by a factor 52 ... 84 - 98 are grouped by a factor 15 ... 99 - 111 are grouped by a factor 13 ... 112 - 144 are grouped by a factor 11 ... 145 - 162 are grouped by a factor 18 ... 163 - 174 are grouped by a factor 12 ... 175 - 188 are grouped by a factor 14 ... 189 - 203 are grouped by a factor 15 ... 204 - 219 are grouped by a factor 16 ... 220 - 228 are grouped by a factor 9 ... 229 - 239 are grouped by a factor 11 ... 240 - 253 are grouped by a factor 14 ... 254 - 271 are grouped by a factor 18 ... 272 - 286 are grouped by a factor 15 ... 287 - 304 are grouped by a factor 18 ... 305 - 336 are grouped by a factor 32 ... 337 - 376 are grouped by a factor 40 ... 377 - 436 are grouped by a factor 60 ... 437 - 1023 are grouped by a factor 587 ... --------------------------------------------- ... ...... exiting, changes written to file : ad45016000s010212_1.pi ** grppha 2.8.1 completed successfully-> Source occupies chip(s) 1
Sisrmg Version 1.1, Configured 04/97 This version resolves *all* known keyword incompatibilities with other FTOOLS tasks. If you have previously fudged *any* keywords in the PHA file to compensate, incorrect results will follow. Setting 1st PHA channel to 0 Making v1.1 1180x1024 S0C1 Bright2 PI RMF Calibration data files: ecd = ./sis0c1p40_290296.fits cti = ./sisph2pi_110397.fits echo = ./sisechos_290296.fits rdd = ./sisrddis_290296.fits Please stand by... ...Done.-> Generating ad45016000s010212_1.arf with point=no
ASCAARF vers 2.81 28 Aug 1998.
Input WMAP array has size 20 by 29 bins
expanded to 20 by 29 bins
First WMAP bin is at detector pixel 224 392
8 detector pixels per WMAP bin
WMAP bin size is 0.21600 mm
0.21216 arcmin
Selected region size is 1.4348 arcmin^2
Optical axis is detector pixel 662.72 559.02
1180 energies from RMF file
Effective area fudge applied
Arf filter applied
Total counts in region = 8.65000E+02
Weighted mean angle from optical axis = 10.065 arcmin
-> Extracting ad45016000s010212_2.pi from ad45016000s032002_2.reg and:ad45016000s000112h.evt ad45016000s000212m.evt-> Deleting ad45016000s010212_2.pi since it has 492 events
1 ad45016000s100102h.evt 2011 1 ad45016000s100202m.evt 2011-> Fetching SIS1_NOTCHIP0.1
ad45016000s100102h.evt ad45016000s100202m.evt-> Grouping ad45016000s110102_1.pi to 40 counts/bin
------------------------- MANDATORY KEYWORDS/VALUES ------------------------- -------------------------------------------------------------------- -------------------------------------------------------------------- EXTNAME - SPECTRUM Name of this BINTABLE TELESCOP - ASCA Mission/Satellite name INSTRUME - SIS1 Instrument/Detector FILTER - NONE Instrument filter in use EXPOSURE - 7736.0 Integration time (in secs) of PHA data AREASCAL - 1.0000 Area scaling factor BACKSCAL - 1.68066E-02 Background scaling factor BACKFILE - NONE Associated background file CORRSCAL - 1.0000 Correlation scaling factor CORRFILE - none Associated correlation file RESPFILE - NONE Associated redistribution matrix file ANCRFILE - none Associated ancillary response file XFLT0001 - none XSPEC selection filter POISSERR - TRUE Whether Poissonian errors apply CHANTYPE - PI Whether channels have been corrected TLMIN1 - 0 First legal Detector channel DETCHANS - 512 No. of legal detector channels NCHAN - 512 No. of detector channels in dataset PHAVERSN - 1.1.0 OGIP FITS version number STAT_ERR - FALSE Statistical Error SYS_ERR - TRUE Fractional Systematic Error QUALITY - TRUE Quality Flag GROUPING - FALSE Grouping Flag -------------------------------------------------------------------- -------------------------------------------------------------------- ... ... -------- ... GROUPING ... -------- ... --------------------------------------------- ... Channel Grouping (Channel-Channel) : ... 0 - 16 of undefined grouping (Channel quality=bad) ... 17 - 49 are grouped by a factor 33 ... 50 - 75 are grouped by a factor 13 ... 76 - 108 are grouped by a factor 11 ... 109 - 132 are grouped by a factor 12 ... 133 - 147 are grouped by a factor 15 ... 148 - 166 are grouped by a factor 19 ... 167 - 203 are grouped by a factor 37 ... 204 - 335 are grouped by a factor 132 ... 336 - 511 of undefined grouping (Channel quality=bad) ... --------------------------------------------- ... ...... exiting, changes written to file : ad45016000s110102_1.pi ** grppha 2.8.1 completed successfully-> Source occupies chip(s) 3
Sisrmg Version 1.1, Configured 04/97 This version resolves *all* known keyword incompatibilities with other FTOOLS tasks. If you have previously fudged *any* keywords in the PHA file to compensate, incorrect results will follow. Setting 1st PHA channel to 0 Making v1.1 1180x512 S1C3 Bright PI RMF Calibration data files: ecd = ./sis1c3p40_290296.fits cti = ./sisph2pi_110397.fits echo = ./sisechos_290296.fits rdd = ./sisrddis_290296.fits Please stand by... ...Done.-> Generating ad45016000s110102_1.arf with point=no
ASCAARF vers 2.81 28 Aug 1998.
Input WMAP array has size 20 by 25 bins
expanded to 20 by 25 bins
First WMAP bin is at detector pixel 224 432
8 detector pixels per WMAP bin
WMAP bin size is 0.21600 mm
0.21216 arcmin
Selected region size is 1.2104 arcmin^2
Optical axis is detector pixel 618.28 773.83
1180 energies from RMF file
Effective area fudge applied
Arf filter applied
Total counts in region = 4.87000E+02
Weighted mean angle from optical axis = 10.679 arcmin
-> Extracting ad45016000s110102_2.pi from ad45016000s132002_2.reg and:ad45016000s100102h.evt ad45016000s100202m.evt-> Deleting ad45016000s110102_2.pi since it has 338 events
1 ad45016000s100112h.evt 2056 1 ad45016000s100212m.evt 2056-> SIS1_NOTCHIP0.1 already present in current directory
ad45016000s100112h.evt ad45016000s100212m.evt-> Grouping ad45016000s110212_1.pi to 40 counts/bin
------------------------- MANDATORY KEYWORDS/VALUES ------------------------- -------------------------------------------------------------------- -------------------------------------------------------------------- EXTNAME - SPECTRUM Name of this BINTABLE TELESCOP - ASCA Mission/Satellite name INSTRUME - SIS1 Instrument/Detector FILTER - NONE Instrument filter in use EXPOSURE - 7736.0 Integration time (in secs) of PHA data AREASCAL - 1.0000 Area scaling factor BACKSCAL - 1.68066E-02 Background scaling factor BACKFILE - NONE Associated background file CORRSCAL - 1.0000 Correlation scaling factor CORRFILE - none Associated correlation file RESPFILE - NONE Associated redistribution matrix file ANCRFILE - none Associated ancillary response file XFLT0001 - none XSPEC selection filter POISSERR - TRUE Whether Poissonian errors apply CHANTYPE - PI Whether channels have been corrected TLMIN1 - 0 First legal Detector channel DETCHANS - 1024 No. of legal detector channels NCHAN - 1024 No. of detector channels in dataset PHAVERSN - 1.1.0 OGIP FITS version number STAT_ERR - FALSE Statistical Error SYS_ERR - TRUE Fractional Systematic Error QUALITY - TRUE Quality Flag GROUPING - FALSE Grouping Flag -------------------------------------------------------------------- -------------------------------------------------------------------- ... ... -------- ... GROUPING ... -------- ... --------------------------------------------- ... Channel Grouping (Channel-Channel) : ... 0 - 32 of undefined grouping (Channel quality=bad) ... 33 - 99 are grouped by a factor 67 ... 100 - 151 are grouped by a factor 26 ... 152 - 173 are grouped by a factor 22 ... 174 - 194 are grouped by a factor 21 ... 195 - 240 are grouped by a factor 23 ... 241 - 262 are grouped by a factor 22 ... 263 - 295 are grouped by a factor 33 ... 296 - 339 are grouped by a factor 44 ... 340 - 406 are grouped by a factor 67 ... 407 - 671 are grouped by a factor 265 ... 672 - 1023 of undefined grouping (Channel quality=bad) ... --------------------------------------------- ... ...... exiting, changes written to file : ad45016000s110212_1.pi ** grppha 2.8.1 completed successfully-> Source occupies chip(s) 3
Sisrmg Version 1.1, Configured 04/97 This version resolves *all* known keyword incompatibilities with other FTOOLS tasks. If you have previously fudged *any* keywords in the PHA file to compensate, incorrect results will follow. Setting 1st PHA channel to 0 Making v1.1 1180x1024 S1C3 Bright2 PI RMF Calibration data files: ecd = ./sis1c3p40_290296.fits cti = ./sisph2pi_110397.fits echo = ./sisechos_290296.fits rdd = ./sisrddis_290296.fits Please stand by... ...Done.-> Generating ad45016000s110212_1.arf with point=no
ASCAARF vers 2.81 28 Aug 1998.
Input WMAP array has size 20 by 25 bins
expanded to 20 by 25 bins
First WMAP bin is at detector pixel 224 432
8 detector pixels per WMAP bin
WMAP bin size is 0.21600 mm
0.21216 arcmin
Selected region size is 1.2104 arcmin^2
Optical axis is detector pixel 618.28 773.83
1180 energies from RMF file
Effective area fudge applied
Arf filter applied
Total counts in region = 4.89000E+02
Weighted mean angle from optical axis = 10.667 arcmin
-> Extracting ad45016000s110212_2.pi from ad45016000s132002_2.reg and:ad45016000s100112h.evt ad45016000s100212m.evt-> Deleting ad45016000s110212_2.pi since it has 345 events
1 ad45016000g200170m.evt 24133 1 ad45016000g200270h.evt 24133 1 ad45016000g200370l.evt 24133-> GIS2_REGION256.4 already present in current directory
ad45016000g200170m.evt ad45016000g200270h.evt ad45016000g200370l.evt-> Deleting ad45016000g210170_1.pi since it has 257 events
ad45016000g200170m.evt ad45016000g200270h.evt ad45016000g200370l.evt-> Correcting ad45016000g210170_2.pi for dead time
... read all the files from deadlist.tmp-> Grouping ad45016000g210170_2.pi to 40 counts/bin
------------------------- MANDATORY KEYWORDS/VALUES ------------------------- -------------------------------------------------------------------- -------------------------------------------------------------------- EXTNAME - SPECTRUM Name of this BINTABLE TELESCOP - ASCA Mission/Satellite name INSTRUME - GIS2 Instrument/Detector FILTER - NONE Instrument filter in use EXPOSURE - 7652.1 Integration time (in secs) of PHA data AREASCAL - 1.0000 Area scaling factor BACKSCAL - 2.62756E-02 Background scaling factor BACKFILE - NONE Associated background file CORRSCAL - 1.0000 Correlation scaling factor CORRFILE - none Associated correlation file RESPFILE - NONE Associated redistribution matrix file ANCRFILE - none Associated ancillary response file XFLT0001 - none XSPEC selection filter POISSERR - TRUE Whether Poissonian errors apply CHANTYPE - PI Whether channels have been corrected TLMIN1 - 0 First legal Detector channel DETCHANS - 1024 No. of legal detector channels NCHAN - 1024 No. of detector channels in dataset PHAVERSN - 1.1.0 OGIP FITS version number STAT_ERR - FALSE Statistical Error SYS_ERR - TRUE Fractional Systematic Error QUALITY - TRUE Quality Flag GROUPING - TRUE Grouping Flag -------------------------------------------------------------------- -------------------------------------------------------------------- ... ... -------- ... GROUPING ... -------- ... --------------------------------------------- ... Channel Grouping (Channel-Channel) : ... 0 - 42 are grouped by a factor 43 ... 43 - 72 are grouped by a factor 30 ... 73 - 87 are grouped by a factor 15 ... 88 - 98 are grouped by a factor 11 ... 99 - 105 are grouped by a factor 7 ... 106 - 111 are grouped by a factor 6 ... 112 - 115 are grouped by a factor 4 ... 116 - 120 are grouped by a factor 5 ... 121 - 128 are grouped by a factor 4 ... 129 - 134 are grouped by a factor 3 ... 135 - 138 are grouped by a factor 4 ... 139 - 140 are grouped by a factor 2 ... 141 - 152 are grouped by a factor 3 ... 153 - 156 are grouped by a factor 2 ... 157 - 159 are grouped by a factor 3 ... 160 - 163 are grouped by a factor 2 ... 164 - 166 are grouped by a factor 3 ... 167 - 168 are grouped by a factor 2 ... 169 - 171 are grouped by a factor 3 ... 172 - 181 are grouped by a factor 2 ... 182 - 199 are grouped by a factor 3 ... 200 - 201 are grouped by a factor 2 ... 202 - 213 are grouped by a factor 3 ... 214 - 215 are grouped by a factor 2 ... 216 - 224 are grouped by a factor 3 ... 225 - 232 are grouped by a factor 4 ... 233 - 238 are grouped by a factor 3 ... 239 - 246 are grouped by a factor 4 ... 247 - 255 are grouped by a factor 3 ... 256 - 259 are grouped by a factor 4 ... 260 - 268 are grouped by a factor 3 ... 269 - 272 are grouped by a factor 4 ... 273 - 275 are grouped by a factor 3 ... 276 - 291 are grouped by a factor 4 ... 292 - 296 are grouped by a factor 5 ... 297 - 320 are grouped by a factor 4 ... 321 - 325 are grouped by a factor 5 ... 326 - 333 are grouped by a factor 4 ... 334 - 339 are grouped by a factor 6 ... 340 - 343 are grouped by a factor 4 ... 344 - 348 are grouped by a factor 5 ... 349 - 354 are grouped by a factor 6 ... 355 - 358 are grouped by a factor 4 ... 359 - 364 are grouped by a factor 6 ... 365 - 371 are grouped by a factor 7 ... 372 - 379 are grouped by a factor 8 ... 380 - 384 are grouped by a factor 5 ... 385 - 388 are grouped by a factor 4 ... 389 - 397 are grouped by a factor 9 ... 398 - 409 are grouped by a factor 6 ... 410 - 418 are grouped by a factor 9 ... 419 - 424 are grouped by a factor 6 ... 425 - 435 are grouped by a factor 11 ... 436 - 447 are grouped by a factor 12 ... 448 - 461 are grouped by a factor 14 ... 462 - 480 are grouped by a factor 19 ... 481 - 507 are grouped by a factor 27 ... 508 - 563 are grouped by a factor 56 ... 564 - 694 are grouped by a factor 131 ... 695 - 1023 of undefined grouping (Channel quality=bad) ... --------------------------------------------- ... ...... exiting, changes written to file : ad45016000g210170_2.pi ** grppha 2.8.1 completed successfully-> Fetching gis2v4_0.rmf
ASCAARF vers 2.81 28 Aug 1998.
Input WMAP array has size 34 by 66 bins
expanded to 64 by 128 bins
First WMAP bin is at detector pixel 27 77
1 detector pixels per WMAP bin
WMAP bin size is 0.25000 mm
0.24555 arcmin
Selected region size is 103.85 arcmin^2
Optical axis is detector pixel 133.00 130.96
201 energies from RMF file
Effective area fudge applied
Arf filter applied
Total counts in region = 4.52100E+03
Weighted mean angle from optical axis = 19.221 arcmin
-> Standard Output From STOOL group_event_files:1 ad45016000g300170m.evt 24455 1 ad45016000g300270h.evt 24455 1 ad45016000g300370l.evt 24455-> GIS3_REGION256.4 already present in current directory
ad45016000g300170m.evt ad45016000g300270h.evt ad45016000g300370l.evt-> Deleting ad45016000g310170_1.pi since it has 306 events
ad45016000g300170m.evt ad45016000g300270h.evt ad45016000g300370l.evt-> Correcting ad45016000g310170_2.pi for dead time
... read all the files from deadlist.tmp-> Grouping ad45016000g310170_2.pi to 40 counts/bin
------------------------- MANDATORY KEYWORDS/VALUES ------------------------- -------------------------------------------------------------------- -------------------------------------------------------------------- EXTNAME - SPECTRUM Name of this BINTABLE TELESCOP - ASCA Mission/Satellite name INSTRUME - GIS3 Instrument/Detector FILTER - NONE Instrument filter in use EXPOSURE - 7648.1 Integration time (in secs) of PHA data AREASCAL - 1.0000 Area scaling factor BACKSCAL - 3.11890E-02 Background scaling factor BACKFILE - NONE Associated background file CORRSCAL - 1.0000 Correlation scaling factor CORRFILE - none Associated correlation file RESPFILE - NONE Associated redistribution matrix file ANCRFILE - none Associated ancillary response file XFLT0001 - none XSPEC selection filter POISSERR - TRUE Whether Poissonian errors apply CHANTYPE - PI Whether channels have been corrected TLMIN1 - 0 First legal Detector channel DETCHANS - 1024 No. of legal detector channels NCHAN - 1024 No. of detector channels in dataset PHAVERSN - 1.1.0 OGIP FITS version number STAT_ERR - FALSE Statistical Error SYS_ERR - TRUE Fractional Systematic Error QUALITY - TRUE Quality Flag GROUPING - TRUE Grouping Flag -------------------------------------------------------------------- -------------------------------------------------------------------- ... ... -------- ... GROUPING ... -------- ... --------------------------------------------- ... Channel Grouping (Channel-Channel) : ... 0 - 36 are grouped by a factor 37 ... 37 - 59 are grouped by a factor 23 ... 60 - 78 are grouped by a factor 19 ... 79 - 91 are grouped by a factor 13 ... 92 - 98 are grouped by a factor 7 ... 99 - 103 are grouped by a factor 5 ... 104 - 115 are grouped by a factor 4 ... 116 - 127 are grouped by a factor 3 ... 128 - 129 are grouped by a factor 2 ... 130 - 138 are grouped by a factor 3 ... 139 - 160 are grouped by a factor 2 ... 161 - 163 are grouped by a factor 3 ... 164 - 193 are grouped by a factor 2 ... 194 - 196 are grouped by a factor 3 ... 197 - 198 are grouped by a factor 2 ... 199 - 201 are grouped by a factor 3 ... 202 - 209 are grouped by a factor 2 ... 210 - 212 are grouped by a factor 3 ... 213 - 214 are grouped by a factor 2 ... 215 - 217 are grouped by a factor 3 ... 218 - 219 are grouped by a factor 2 ... 220 - 222 are grouped by a factor 3 ... 223 - 226 are grouped by a factor 2 ... 227 - 229 are grouped by a factor 3 ... 230 - 231 are grouped by a factor 2 ... 232 - 240 are grouped by a factor 3 ... 241 - 242 are grouped by a factor 2 ... 243 - 245 are grouped by a factor 3 ... 246 - 247 are grouped by a factor 2 ... 248 - 250 are grouped by a factor 3 ... 251 - 252 are grouped by a factor 2 ... 253 - 255 are grouped by a factor 3 ... 256 - 257 are grouped by a factor 2 ... 258 - 275 are grouped by a factor 3 ... 276 - 277 are grouped by a factor 2 ... 278 - 304 are grouped by a factor 3 ... 305 - 316 are grouped by a factor 4 ... 317 - 319 are grouped by a factor 3 ... 320 - 343 are grouped by a factor 4 ... 344 - 352 are grouped by a factor 3 ... 353 - 356 are grouped by a factor 4 ... 357 - 366 are grouped by a factor 5 ... 367 - 370 are grouped by a factor 4 ... 371 - 375 are grouped by a factor 5 ... 376 - 383 are grouped by a factor 4 ... 384 - 398 are grouped by a factor 5 ... 399 - 410 are grouped by a factor 6 ... 411 - 415 are grouped by a factor 5 ... 416 - 422 are grouped by a factor 7 ... 423 - 440 are grouped by a factor 6 ... 441 - 448 are grouped by a factor 8 ... 449 - 457 are grouped by a factor 9 ... 458 - 467 are grouped by a factor 10 ... 468 - 476 are grouped by a factor 9 ... 477 - 488 are grouped by a factor 12 ... 489 - 509 are grouped by a factor 21 ... 510 - 536 are grouped by a factor 27 ... 537 - 566 are grouped by a factor 30 ... 567 - 646 are grouped by a factor 80 ... 647 - 1000 are grouped by a factor 354 ... 1001 - 1023 of undefined grouping (Channel quality=bad) ... --------------------------------------------- ... ...... exiting, changes written to file : ad45016000g310170_2.pi ** grppha 2.8.1 completed successfully-> Fetching gis3v4_0.rmf
ASCAARF vers 2.81 28 Aug 1998.
Input WMAP array has size 39 by 66 bins
expanded to 64 by 128 bins
First WMAP bin is at detector pixel 30 78
1 detector pixels per WMAP bin
WMAP bin size is 0.25000 mm
0.24555 arcmin
Selected region size is 123.27 arcmin^2
Optical axis is detector pixel 119.36 134.44
201 energies from RMF file
Effective area fudge applied
Arf filter applied
Total counts in region = 6.13400E+03
Weighted mean angle from optical axis = 15.338 arcmin
-> Plotting ad45016000g210170_2_pi.ps from ad45016000g210170_2.pi
XSPEC 9.01 22:08:05 5-Jan-00
Plot device not set, use "cpd" to set it
Type "help" or "?" for further information
!XSPEC> data ad45016000g210170_2.pi
Net count rate (cts/s) for file 1 0.5966 +/- 9.1292E-03
1 data set is in use
!XSPEC> setplot energy
!XSPEC> ignore bad
!XSPEC> iplot
!PLT> log y on
!PLT> rescale y
!PLT> hard /ps
!PLT> quit
!XSPEC> exit
!Do you really want to exit (y) y
XSPEC: quit
-> Plotting ad45016000g310170_2_pi.ps from ad45016000g310170_2.pi
XSPEC 9.01 22:08:18 5-Jan-00
Plot device not set, use "cpd" to set it
Type "help" or "?" for further information
!XSPEC> data ad45016000g310170_2.pi
Net count rate (cts/s) for file 1 0.8058 +/- 1.0284E-02
1 data set is in use
!XSPEC> setplot energy
!XSPEC> ignore bad
!XSPEC> iplot
!PLT> log y on
!PLT> rescale y
!PLT> hard /ps
!PLT> quit
!XSPEC> exit
!Do you really want to exit (y) y
XSPEC: quit
-> Plotting ad45016000s010102_1_pi.ps from ad45016000s010102_1.pi
XSPEC 9.01 22:08:31 5-Jan-00
Plot device not set, use "cpd" to set it
Type "help" or "?" for further information
!XSPEC> data ad45016000s010102_1.pi
Net count rate (cts/s) for file 1 0.1001 +/- 3.9371E-03
1 data set is in use
!XSPEC> setplot energy
!XSPEC> ignore bad
!XSPEC> iplot
!PLT> log y on
!PLT> rescale y
!PLT> hard /ps
!PLT> quit
!XSPEC> exit
!Do you really want to exit (y) y
XSPEC: quit
-> Plotting ad45016000s010212_1_pi.ps from ad45016000s010212_1.pi
XSPEC 9.01 22:08:43 5-Jan-00
Plot device not set, use "cpd" to set it
Type "help" or "?" for further information
!XSPEC> data ad45016000s010212_1.pi
Net count rate (cts/s) for file 1 0.1024 +/- 3.5134E-03
1 data set is in use
!XSPEC> setplot energy
!XSPEC> ignore bad
!XSPEC> iplot
!PLT> log y on
!PLT> rescale y
!PLT> hard /ps
!PLT> quit
!XSPEC> exit
!Do you really want to exit (y) y
XSPEC: quit
-> Plotting ad45016000s110102_1_pi.ps from ad45016000s110102_1.pi
XSPEC 9.01 22:09:01 5-Jan-00
Plot device not set, use "cpd" to set it
Type "help" or "?" for further information
!XSPEC> data ad45016000s110102_1.pi
Net count rate (cts/s) for file 1 6.5538E-02+/- 3.3832E-03
1 data set is in use
!XSPEC> setplot energy
!XSPEC> ignore bad
!XSPEC> iplot
!PLT> log y on
!PLT> rescale y
!PLT> hard /ps
!PLT> quit
!XSPEC> exit
!Do you really want to exit (y) y
XSPEC: quit
-> Plotting ad45016000s110212_1_pi.ps from ad45016000s110212_1.pi
XSPEC 9.01 22:09:16 5-Jan-00
Plot device not set, use "cpd" to set it
Type "help" or "?" for further information
!XSPEC> data ad45016000s110212_1.pi
Net count rate (cts/s) for file 1 6.5667E-02+/- 3.8303E-03
1 data set is in use
!XSPEC> setplot energy
!XSPEC> ignore bad
!XSPEC> iplot
!PLT> log y on
!PLT> rescale y
!PLT> hard /ps
!PLT> quit
!XSPEC> exit
!Do you really want to exit (y) y
XSPEC: quit
Type "help" for information
[1]xronos> Current User Interface is ; command driven
[2]xronos> Enter up to 50 input filenames and options for series 1 (or rtn)
Ser. A filename 1 +options[.rbf]=> ad45016000s000002_1.lc
Selected FITS extensions: 1 - RATE TABLE;
Source ............ AGPS267.3-27.4 Start Time (d) .... 10706 12:42:41.431
FITS Extension .... 1 - `RATE ` Stop Time (d) ..... 10707 20:49:37.431
No. of Rows ....... 20 Bin Time (s) ...... 472.0
Right Ascension ... 2.6723E+02 Internal time sys.. Converted to TJD
Declination ....... -2.7485E+01 Experiment ........ ASCA SIS0
Filter ............ NONE
Corrections applied: Vignetting - No ; Deadtime - No ; Bkgd - No ; Clock - No
Selected Columns: 1 - Time; 2 - Y-axis; 3 - Y-error;
File contains binned data.
Ser. A filename 2 +options[.rbf]=>
Enter up to 50 input filenames and options for series 2 (or rtn)
Ser. B filename 1 +options[.rbf]=>
Enter up to 50 input filenames and options for series 3 (or rtn)
Ser. C filename 1 +options[.rbf]=>
[3]xronos>
Maximum of 1 Intvs. with 245 Newbins of 472.026 (s)
Intv 1 Start10706 12:46:37
Ser.1 Avg 0.1065 Chisq 33.56 Var 0.4788E-03 Newbs. 20
Min 0.4649E-01 Max 0.1335 expVar 0.2853E-03 Bins 20
Results from Statistical Analysis
Newbin Integration Time (s).. 472.03
Interval Duration (s)........ 0.11517E+06
No. of Newbins .............. 20
Average (c/s) ............... 0.10646 +/- 0.39E-02
Standard Deviation (c/s)..... 0.21881E-01
Minimum (c/s)................ 0.46494E-01
Maximum (c/s)................ 0.13347
Variance ((c/s)**2).......... 0.47879E-03 +/- 0.16E-03
Expected Variance ((c/s)**2). 0.28531E-03 +/- 0.93E-04
Third Moment ((c/s)**3)......-0.81942E-05
Average Deviation (c/s)...... 0.17549E-01
Skewness.....................-0.78214 +/- 0.55
Kurtosis..................... 0.54300 +/- 1.1
RMS fractional variation....< 0.12059 (3 sigma)
Chi-Square................... 33.563 dof 19
Chi-Square Prob of constancy. 0.20684E-01 (0 means < 1.e-38)
Kolm.-Smir. Prob of constancy 0.60019E-02 (0 means < 1.e-38)
[4]xronos> [5]xronos>
Maximum of 1 Intvs. with 245 Newbins of 472.026 (s)
Intv 1 Start10706 12:46:37
Ser.1 Avg 0.1065 Chisq 33.56 Var 0.4788E-03 Newbs. 20
Min 0.4649E-01 Max 0.1335 expVar 0.2853E-03 Bins 20
Light curve ready !
Frme 1 Written to output file : xronos.qlc1
PLT> LA File ad45016000s000002_1.lc
PLT> hard /ps
PLT> [6]xronos>
-> Extracting events from region ad45016000s032002_2.reg
Type "help" for information
[1]xronos> Current User Interface is ; command driven
[2]xronos> Enter up to 50 input filenames and options for series 1 (or rtn)
Ser. A filename 1 +options[.rbf]=> ad45016000s100002_1.lc
Selected FITS extensions: 1 - RATE TABLE;
Source ............ AGPS267.3-27.4 Start Time (d) .... 10706 12:42:09.431
FITS Extension .... 1 - `RATE ` Stop Time (d) ..... 10707 20:49:37.431
No. of Rows ....... 11 Bin Time (s) ...... 708.4
Right Ascension ... 2.6723E+02 Internal time sys.. Converted to TJD
Declination ....... -2.7485E+01 Experiment ........ ASCA SIS1
Filter ............ NONE
Corrections applied: Vignetting - No ; Deadtime - No ; Bkgd - No ; Clock - No
Selected Columns: 1 - Time; 2 - Y-axis; 3 - Y-error;
File contains binned data.
Ser. A filename 2 +options[.rbf]=>
Enter up to 50 input filenames and options for series 2 (or rtn)
Ser. B filename 1 +options[.rbf]=>
Enter up to 50 input filenames and options for series 3 (or rtn)
Ser. C filename 1 +options[.rbf]=>
[3]xronos>
Maximum of 1 Intvs. with 164 Newbins of 708.425 (s)
Intv 1 Start10706 12:48: 3
Ser.1 Avg 0.7210E-01 Chisq 9.573 Var 0.1203E-03 Newbs. 11
Min 0.4665E-01 Max 0.8457E-01expVar 0.1382E-03 Bins 11
Results from Statistical Analysis
Newbin Integration Time (s).. 708.42
Interval Duration (s)........ 0.11476E+06
No. of Newbins .............. 11
Average (c/s) ............... 0.72104E-01 +/- 0.37E-02
Standard Deviation (c/s)..... 0.10968E-01
Minimum (c/s)................ 0.46653E-01
Maximum (c/s)................ 0.84572E-01
Variance ((c/s)**2).......... 0.12031E-03 +/- 0.54E-04
Expected Variance ((c/s)**2). 0.13824E-03 +/- 0.62E-04
Third Moment ((c/s)**3)......-0.16567E-05
Average Deviation (c/s)...... 0.79982E-02
Skewness..................... -1.2555 +/- 0.74
Kurtosis..................... 0.44521 +/- 1.5
RMS fractional variation....< 0.23110 (3 sigma)
Chi-Square................... 9.5731 dof 10
Chi-Square Prob of constancy. 0.47864 (0 means < 1.e-38)
Kolm.-Smir. Prob of constancy 0.14797 (0 means < 1.e-38)
[4]xronos> [5]xronos>
Maximum of 1 Intvs. with 164 Newbins of 708.425 (s)
Intv 1 Start10706 12:48: 3
Ser.1 Avg 0.7210E-01 Chisq 9.573 Var 0.1203E-03 Newbs. 11
Min 0.4665E-01 Max 0.8457E-01expVar 0.1382E-03 Bins 11
Light curve ready !
Frme 1 Written to output file : xronos.qlc1
PLT> LA File ad45016000s100002_1.lc
PLT> hard /ps
PLT> [6]xronos>
-> Extracting events from region ad45016000s132002_2.reg
Type "help" for information
[1]xronos> Current User Interface is ; command driven
[2]xronos> Enter up to 50 input filenames and options for series 1 (or rtn)
Ser. A filename 1 +options[.rbf]=> ad45016000g200070_2.lc
Selected FITS extensions: 1 - RATE TABLE;
Source ............ AGPS267.3-27.4 Start Time (d) .... 10706 12:39:13.422
FITS Extension .... 1 - `RATE ` Stop Time (d) ..... 10706 19:58:25.431
No. of Rows ....... 93 Bin Time (s) ...... 83.81
Right Ascension ... 2.6723E+02 Internal time sys.. Converted to TJD
Declination ....... -2.7485E+01 Experiment ........ ASCA GIS2
Filter ............ NONE
Corrections applied: Vignetting - No ; Deadtime - No ; Bkgd - No ; Clock - No
Selected Columns: 1 - Time; 2 - Y-axis; 3 - Y-error;
File contains binned data.
Ser. A filename 2 +options[.rbf]=>
Enter up to 50 input filenames and options for series 2 (or rtn)
Ser. B filename 1 +options[.rbf]=>
Enter up to 50 input filenames and options for series 3 (or rtn)
Ser. C filename 1 +options[.rbf]=>
[3]xronos>
Maximum of 1 Intvs. with 315 Newbins of 83.8125 (s)
Intv 1 Start10706 12:39:55
Ser.1 Avg 0.5950 Chisq 98.26 Var 0.7955E-02 Newbs. 93
Min 0.3937 Max 0.7755 expVar 0.7529E-02 Bins 93
Results from Statistical Analysis
Newbin Integration Time (s).. 83.812
Interval Duration (s)........ 26233.
No. of Newbins .............. 93
Average (c/s) ............... 0.59496 +/- 0.90E-02
Standard Deviation (c/s)..... 0.89189E-01
Minimum (c/s)................ 0.39374
Maximum (c/s)................ 0.77554
Variance ((c/s)**2).......... 0.79546E-02 +/- 0.12E-02
Expected Variance ((c/s)**2). 0.75288E-02 +/- 0.11E-02
Third Moment ((c/s)**3)......-0.82676E-04
Average Deviation (c/s)...... 0.74163E-01
Skewness.....................-0.11653 +/- 0.25
Kurtosis.....................-0.55780 +/- 0.51
RMS fractional variation....< 0.97216E-01 (3 sigma)
Chi-Square................... 98.260 dof 92
Chi-Square Prob of constancy. 0.30844 (0 means < 1.e-38)
Kolm.-Smir. Prob of constancy 0.55580E-01 (0 means < 1.e-38)
[4]xronos> [5]xronos>
Maximum of 1 Intvs. with 315 Newbins of 83.8125 (s)
Intv 1 Start10706 12:39:55
Ser.1 Avg 0.5950 Chisq 98.26 Var 0.7955E-02 Newbs. 93
Min 0.3937 Max 0.7755 expVar 0.7529E-02 Bins 93
Light curve ready !
Frme 1 Written to output file : xronos.qlc1
PLT> LA File ad45016000g200070_2.lc
PLT> hard /ps
PLT> [6]xronos>
-> TIMEDEL=5.0000000000E-01 for ad45016000g300170m.evt
Type "help" for information
[1]xronos> Current User Interface is ; command driven
[2]xronos> Enter up to 50 input filenames and options for series 1 (or rtn)
Ser. A filename 1 +options[.rbf]=> ad45016000g300070_2.lc
Selected FITS extensions: 1 - RATE TABLE;
Source ............ AGPS267.3-27.4 Start Time (d) .... 10706 12:39:13.422
FITS Extension .... 1 - `RATE ` Stop Time (d) ..... 10706 19:58:25.431
No. of Rows ....... 124 Bin Time (s) ...... 62.05
Right Ascension ... 2.6723E+02 Internal time sys.. Converted to TJD
Declination ....... -2.7485E+01 Experiment ........ ASCA GIS3
Filter ............ NONE
Corrections applied: Vignetting - No ; Deadtime - No ; Bkgd - No ; Clock - No
Selected Columns: 1 - Time; 2 - Y-axis; 3 - Y-error;
File contains binned data.
Ser. A filename 2 +options[.rbf]=>
Enter up to 50 input filenames and options for series 2 (or rtn)
Ser. B filename 1 +options[.rbf]=>
Enter up to 50 input filenames and options for series 3 (or rtn)
Ser. C filename 1 +options[.rbf]=>
[3]xronos>
Maximum of 1 Intvs. with 425 Newbins of 62.0484 (s)
Intv 1 Start10706 12:39:44
Ser.1 Avg 0.8064 Chisq 130.0 Var 0.1433E-01 Newbs. 124
Min 0.4996 Max 1.209 expVar 0.1367E-01 Bins 124
Results from Statistical Analysis
Newbin Integration Time (s).. 62.048
Interval Duration (s)........ 26309.
No. of Newbins .............. 124
Average (c/s) ............... 0.80643 +/- 0.11E-01
Standard Deviation (c/s)..... 0.11970
Minimum (c/s)................ 0.49961
Maximum (c/s)................ 1.2087
Variance ((c/s)**2).......... 0.14329E-01 +/- 0.18E-02
Expected Variance ((c/s)**2). 0.13668E-01 +/- 0.17E-02
Third Moment ((c/s)**3)...... 0.58434E-03
Average Deviation (c/s)...... 0.95826E-01
Skewness..................... 0.34068 +/- 0.22
Kurtosis..................... 0.53579 +/- 0.44
RMS fractional variation....< 0.89153E-01 (3 sigma)
Chi-Square................... 130.00 dof 123
Chi-Square Prob of constancy. 0.31549 (0 means < 1.e-38)
Kolm.-Smir. Prob of constancy 0.86642E-01 (0 means < 1.e-38)
[4]xronos> [5]xronos>
Maximum of 1 Intvs. with 425 Newbins of 62.0484 (s)
Intv 1 Start10706 12:39:44
Ser.1 Avg 0.8064 Chisq 130.0 Var 0.1433E-01 Newbs. 124
Min 0.4996 Max 1.209 expVar 0.1367E-01 Bins 124
Light curve ready !
Frme 1 Written to output file : xronos.qlc1
PLT> LA File ad45016000g300070_2.lc
PLT> hard /ps
PLT> [6]xronos>
-> Merging GTIs from the following files:ad45016000g200170m.evt[2] ad45016000g200270h.evt[2] ad45016000g200370l.evt[2]-> Making L1 light curve of ft970915_1153_2050G2HK.fits with irate=HIGH
ghkcurve: ALLGTI found in input HK file, will be applied to data. ghkcurve: 21872 output records from 21883 good input G2_L1 records.-> Making L1 light curve of ft970915_1153_2050G2HK.fits with irate=HI+MED
ghkcurve: ALLGTI found in input HK file, will be applied to data. ghkcurve: 7549 output records from 24196 good input G2_L1 records.-> Merging GTIs from the following files:
ad45016000g300170m.evt[2] ad45016000g300270h.evt[2] ad45016000g300370l.evt[2]-> Making L1 light curve of ft970915_1153_2050G3HK.fits with irate=HIGH
ghkcurve: ALLGTI found in input HK file, will be applied to data. ghkcurve: 21605 output records from 21616 good input G3_L1 records.-> Making L1 light curve of ft970915_1153_2050G3HK.fits with irate=HI+MED
ghkcurve: ALLGTI found in input HK file, will be applied to data. ghkcurve: 7543 output records from 23934 good input G3_L1 records.
*** tlmFrm Version 1.1 (1997-08-25) *** total number of superframes: 5361 Total of 0 sets of frame data are extracted.-> Extracting corner pixel GTIs with the following criteria:
SUNSHINE==0 && T_DY_NT>64 && T_SAA>64 && SAA==0 && COR>6 && (ELV>10 || ELV<10 )-> Extracting GTIs from ft970915_1153_2050.mkf
1 ad45016000g200170m.unf 63285 1 ad45016000g200270h.unf 63285 1 ad45016000g200370l.unf 63285-> Fetching GIS2_CALSRC256.2
XSPEC 9.01 22:30:48 5-Jan-00
Plot device not set, use "cpd" to set it
Type "help" or "?" for further information
!XSPEC> query yes
Querying disabled - assuming answer is yes
!XSPEC> data ad45016000g220170.cal
Net count rate (cts/s) for file 1 0.1680 +/- 2.8205E-03
1 data set is in use
!XSPEC> ignore bad
!XSPEC> ignore **-4.0
!XSPEC> ignore 8.0-**
!XSPEC> model const/b + gauss/b + gauss/b
Background components must be from the additive model list
mo = constant[1] ) + gaussian/b[2] + gaussian/b[3]
Input parameter value, delta, min, bot, top, and max values for ...
Mod parameter 1 of component 1 constant factor
1.000 1.0000E-02 0. 0. 1.0000E+10 1.0000E+10
!
Mod parameter 2 of component 2 gaussian LineE
6.500 5.0000E-02 0. 0. 1.0000E+06 1.0000E+06
! 5.9
Mod parameter 3 of component 2 gaussian Sigma
0.1000 5.0000E-02 0. 0. 10.00 20.00
! 0.0
Mod parameter 4 of component 2 gaussian norm
1.000 1.0000E-02 0. 0. 1.0000E+24 1.0000E+24
!
Mod parameter 5 of component 3 gaussian LineE
6.500 5.0000E-02 0. 0. 1.0000E+06 1.0000E+06
! 6.5
Mod parameter 6 of component 3 gaussian Sigma
0.1000 5.0000E-02 0. 0. 10.00 20.00
! 0.0
Mod parameter 7 of component 3 gaussian norm
1.000 1.0000E-02 0. 0. 1.0000E+24 1.0000E+24
!
---------------------------------------------------------------------------
---------------------------------------------------------------------------
mo = constant[1] ) + gaussian/b[2] + gaussian/b[3]
Model Fit Model Component Parameter Value
par par comp
1 1 1 constant factor 1.00000 +/- 0.
2 2 2 gaussian/b LineE 5.90000 +/- 0.
3 3 2 gaussian/b Sigma 0. +/- 0.
4 4 2 gaussian/b norm 1.00000 +/- 0.
5 5 3 gaussian/b LineE 6.50000 +/- 0.
6 6 3 gaussian/b Sigma 0. +/- 0.
7 7 3 gaussian/b norm 1.00000 +/- 0.
---------------------------------------------------------------------------
---------------------------------------------------------------------------
7 variable fit parameters
Chi-Squared = 9.1228E+05 using 84 PHA bins.
Reduced chi-squared = 1.1848E+04
!XSPEC> newpar 5 = 2 1.101005
6 variable fit parameters
Chi-Squared = 9.0701E+05 using 84 PHA bins.
Reduced chi-squared = 1.1628E+04
!XSPEC> newpar 6 = 3 1.049288
5 variable fit parameters
Chi-Squared = 9.0701E+05 using 84 PHA bins.
Reduced chi-squared = 1.1481E+04
!XSPEC> renorm
Chi-Squared = 730.2 using 84 PHA bins.
Reduced chi-squared = 9.243
!XSPEC> fit
Chi-Squared Lvl Fit param # 1 2 3 4
5
Due to zero model norms
fit parameter 1 is temporarily frozen
568.67 0 1.000 5.895 0.1133 4.4679E-02
4.0697E-02
Due to zero model norms
fit parameter 1 is temporarily frozen
319.49 0 1.000 5.878 0.1629 5.9986E-02
3.6690E-02
Due to zero model norms
fit parameter 1 is temporarily frozen
184.39 -1 1.000 5.937 0.1875 8.1677E-02
2.5778E-02
Due to zero model norms
fit parameter 1 is temporarily frozen
152.61 -2 1.000 6.005 0.2164 9.7580E-02
1.4418E-02
Due to zero model norms
fit parameter 1 is temporarily frozen
149.98 -3 1.000 5.984 0.1989 9.3950E-02
1.7938E-02
Due to zero model norms
fit parameter 1 is temporarily frozen
149.69 -4 1.000 5.991 0.2032 9.5342E-02
1.6521E-02
Due to zero model norms
fit parameter 1 is temporarily frozen
149.63 -5 1.000 5.988 0.2009 9.4822E-02
1.7034E-02
Due to zero model norms
fit parameter 1 is temporarily frozen
149.63 -2 1.000 5.989 0.2016 9.4997E-02
1.6858E-02
---------------------------------------------------------------------------
---------------------------------------------------------------------------
mo = constant[1] ) + gaussian/b[2] + gaussian/b[3]
Model Fit Model Component Parameter Value
par par comp
1 1 1 constant factor 1.00000 +/- -1.0000
2 2 2 gaussian/b LineE 5.98913 +/- 0.11677E-01
3 3 2 gaussian/b Sigma 0.201576 +/- 0.11718E-01
4 4 2 gaussian/b norm 9.499744E-02 +/- 0.28692E-02
5 2 3 gaussian/b LineE 6.59406 = par 2 * 1.1010
6 3 3 gaussian/b Sigma 0.211511 = par 3 * 1.0493
7 5 3 gaussian/b norm 1.685834E-02 +/- 0.21045E-02
---------------------------------------------------------------------------
---------------------------------------------------------------------------
Chi-Squared = 149.6 using 84 PHA bins.
Reduced chi-squared = 1.894
!XSPEC> setplot energy
!XSPEC> iplot data
!PLT> label top GIS2 Calibration Source, should peak near 5.9 keV
!PLT> log x off
!PLT> rescale x 4 8
!PLT> hard /ps
!PLT> quit
!XSPEC> exit
!Do you really want to exit (y) y
XSPEC: quit
-> Calibration source ad45016000g220170.cal peaks at 5.98913 +/- 0.011677 keV1 ad45016000g300170m.unf 61946 1 ad45016000g300270h.unf 61946 1 ad45016000g300370l.unf 61946-> Fetching GIS3_CALSRC256.2
XSPEC 9.01 22:31:56 5-Jan-00
Plot device not set, use "cpd" to set it
Type "help" or "?" for further information
!XSPEC> query yes
Querying disabled - assuming answer is yes
!XSPEC> data ad45016000g320170.cal
Net count rate (cts/s) for file 1 0.1670 +/- 2.8143E-03
1 data set is in use
!XSPEC> ignore bad
!XSPEC> ignore **-4.0
!XSPEC> ignore 8.0-**
!XSPEC> model const/b + gauss/b + gauss/b
Background components must be from the additive model list
mo = constant[1] ) + gaussian/b[2] + gaussian/b[3]
Input parameter value, delta, min, bot, top, and max values for ...
Mod parameter 1 of component 1 constant factor
1.000 1.0000E-02 0. 0. 1.0000E+10 1.0000E+10
!
Mod parameter 2 of component 2 gaussian LineE
6.500 5.0000E-02 0. 0. 1.0000E+06 1.0000E+06
! 5.9
Mod parameter 3 of component 2 gaussian Sigma
0.1000 5.0000E-02 0. 0. 10.00 20.00
! 0.0
Mod parameter 4 of component 2 gaussian norm
1.000 1.0000E-02 0. 0. 1.0000E+24 1.0000E+24
!
Mod parameter 5 of component 3 gaussian LineE
6.500 5.0000E-02 0. 0. 1.0000E+06 1.0000E+06
! 6.5
Mod parameter 6 of component 3 gaussian Sigma
0.1000 5.0000E-02 0. 0. 10.00 20.00
! 0.0
Mod parameter 7 of component 3 gaussian norm
1.000 1.0000E-02 0. 0. 1.0000E+24 1.0000E+24
!
---------------------------------------------------------------------------
---------------------------------------------------------------------------
mo = constant[1] ) + gaussian/b[2] + gaussian/b[3]
Model Fit Model Component Parameter Value
par par comp
1 1 1 constant factor 1.00000 +/- 0.
2 2 2 gaussian/b LineE 5.90000 +/- 0.
3 3 2 gaussian/b Sigma 0. +/- 0.
4 4 2 gaussian/b norm 1.00000 +/- 0.
5 5 3 gaussian/b LineE 6.50000 +/- 0.
6 6 3 gaussian/b Sigma 0. +/- 0.
7 7 3 gaussian/b norm 1.00000 +/- 0.
---------------------------------------------------------------------------
---------------------------------------------------------------------------
7 variable fit parameters
Chi-Squared = 1.1621E+06 using 84 PHA bins.
Reduced chi-squared = 1.5092E+04
!XSPEC> newpar 5 = 2 1.101005
6 variable fit parameters
Chi-Squared = 1.1528E+06 using 84 PHA bins.
Reduced chi-squared = 1.4780E+04
!XSPEC> newpar 6 = 3 1.049288
5 variable fit parameters
Chi-Squared = 1.1528E+06 using 84 PHA bins.
Reduced chi-squared = 1.4592E+04
!XSPEC> renorm
Chi-Squared = 1014. using 84 PHA bins.
Reduced chi-squared = 12.84
!XSPEC> fit
Chi-Squared Lvl Fit param # 1 2 3 4
5
Due to zero model norms
fit parameter 1 is temporarily frozen
809.51 0 1.000 5.893 0.1137 3.7870E-02
3.2370E-02
Due to zero model norms
fit parameter 1 is temporarily frozen
400.91 0 1.000 5.870 0.1576 5.9820E-02
2.7974E-02
Due to zero model norms
fit parameter 1 is temporarily frozen
181.10 -1 1.000 5.953 0.1739 8.8831E-02
1.5037E-02
Due to zero model norms
fit parameter 1 is temporarily frozen
166.90 -2 1.000 5.958 0.1597 9.5020E-02
1.3022E-02
Due to zero model norms
fit parameter 1 is temporarily frozen
166.16 -3 1.000 5.954 0.1521 9.4603E-02
1.3597E-02
Due to zero model norms
fit parameter 1 is temporarily frozen
166.12 -4 1.000 5.955 0.1521 9.4851E-02
1.3361E-02
Due to zero model norms
fit parameter 1 is temporarily frozen
166.10 -5 1.000 5.955 0.1515 9.4781E-02
1.3432E-02
Due to zero model norms
fit parameter 1 is temporarily frozen
166.10 0 1.000 5.955 0.1515 9.4786E-02
1.3427E-02
---------------------------------------------------------------------------
---------------------------------------------------------------------------
mo = constant[1] ) + gaussian/b[2] + gaussian/b[3]
Model Fit Model Component Parameter Value
par par comp
1 1 1 constant factor 1.00000 +/- -1.0000
2 2 2 gaussian/b LineE 5.95469 +/- 0.83858E-02
3 3 2 gaussian/b Sigma 0.151461 +/- 0.10881E-01
4 4 2 gaussian/b norm 9.478555E-02 +/- 0.24627E-02
5 2 3 gaussian/b LineE 6.55614 = par 2 * 1.1010
6 3 3 gaussian/b Sigma 0.158926 = par 3 * 1.0493
7 5 3 gaussian/b norm 1.342650E-02 +/- 0.14510E-02
---------------------------------------------------------------------------
---------------------------------------------------------------------------
Chi-Squared = 166.1 using 84 PHA bins.
Reduced chi-squared = 2.102
!XSPEC> setplot energy
!XSPEC> iplot data
!PLT> label top GIS3 Calibration Source, should peak near 5.9 keV
!PLT> log x off
!PLT> rescale x 4 8
!PLT> hard /ps
!PLT> quit
!XSPEC> exit
!Do you really want to exit (y) y
XSPEC: quit
-> Calibration source ad45016000g320170.cal peaks at 5.95469 +/- 0.0083858 keV
CLEANSIS_V1.6
allocating image arrays...
PROGRAM TO MAKE AN SIS SCIENCE FILE CLEANED OF ANOMALOUS PIXELS.
* Anomalous pixels may consist of at least two populations.
1. Persistent HOT pixels are removed by comparing to the chip mean.
2. Flickering WARM pixels are removed by comparing to the cell mean.
3. In faint areas (zero bgd), flickering pixels are removed with a
cutoff threshold.
Hints:
Choose cell size and thresholds based on the expected background and the PSF.
Use the DIRTYSIS option to examine the anomalous pixel spectra.
Try a multiple pass clean:
Choose a PHA cut to optimize the S/N of the flickering pixels,
then a broad band clean.
Be suspicious of extended source cleans.
For very bright sources you may need to turn off the iteration option.
See the help page for further info (fhelp cleansis)
Poisson clean cell size : 5
Poisson probability threshold : 0.575E-05
Zero Bgd Cutoff threshold (>) : 3
Iterate : F
Dirtysis : F
Minimum PHA value (inclusive) : 0
Maximum PHA value (inclusive) : 4095
open output file: ad45016000s000102h.drk
reading data file: event.tmp
copying primary header to output file...
making chip image...
Total counts in chip images : 365
copy bad pix array...
cleaning chip # 0
cleaning chip # 1
Hot pixels & counts : 5 332
cleaning chip # 2
cleaning chip # 3
Number of pixels rejected : 5
Number of (internal) image counts : 365
Number of image cts rejected (N, %) : 33290.96
By chip : 0 1 2 3
Pixels rejected : 0 5 0 0
Image counts : 0 365 0 0
Image cts rejected: 0 332 0 0
Image cts rej (%) : 0.00 90.96 0.00 0.00
filtering data...
Total counts : 0 365 0 0
Total cts rejected: 0 332 0 0
Total cts rej (%) : 0.00 90.96 0.00 0.00
Number of clean counts accepted : 33
writing history cards...
copying extensions...
writing out hot pixs...
Number of rejected pixels : 5
updating NEVENTS keywords...
closing data file...
closing clean file...
-> Extracting bright and dark Earth events from ad45016000s000112h.unf
CLEANSIS_V1.6
allocating image arrays...
PROGRAM TO MAKE AN SIS SCIENCE FILE CLEANED OF ANOMALOUS PIXELS.
* Anomalous pixels may consist of at least two populations.
1. Persistent HOT pixels are removed by comparing to the chip mean.
2. Flickering WARM pixels are removed by comparing to the cell mean.
3. In faint areas (zero bgd), flickering pixels are removed with a
cutoff threshold.
Hints:
Choose cell size and thresholds based on the expected background and the PSF.
Use the DIRTYSIS option to examine the anomalous pixel spectra.
Try a multiple pass clean:
Choose a PHA cut to optimize the S/N of the flickering pixels,
then a broad band clean.
Be suspicious of extended source cleans.
For very bright sources you may need to turn off the iteration option.
See the help page for further info (fhelp cleansis)
Poisson clean cell size : 5
Poisson probability threshold : 0.575E-05
Zero Bgd Cutoff threshold (>) : 3
Iterate : F
Dirtysis : F
Minimum PHA value (inclusive) : 0
Maximum PHA value (inclusive) : 4095
open output file: ad45016000s000112h.drk
reading data file: event.tmp
copying primary header to output file...
making chip image...
Total counts in chip images : 368
copy bad pix array...
cleaning chip # 0
cleaning chip # 1
Hot pixels & counts : 5 332
cleaning chip # 2
cleaning chip # 3
Number of pixels rejected : 5
Number of (internal) image counts : 368
Number of image cts rejected (N, %) : 33290.22
By chip : 0 1 2 3
Pixels rejected : 0 5 0 0
Image counts : 0 368 0 0
Image cts rejected: 0 332 0 0
Image cts rej (%) : 0.00 90.22 0.00 0.00
filtering data...
Total counts : 0 368 0 0
Total cts rejected: 0 332 0 0
Total cts rej (%) : 0.00 90.22 0.00 0.00
Number of clean counts accepted : 36
writing history cards...
copying extensions...
writing out hot pixs...
Number of rejected pixels : 5
updating NEVENTS keywords...
closing data file...
closing clean file...
-> Extracting bright and dark Earth events from ad45016000s000202m.unf
CLEANSIS_V1.6
allocating image arrays...
PROGRAM TO MAKE AN SIS SCIENCE FILE CLEANED OF ANOMALOUS PIXELS.
* Anomalous pixels may consist of at least two populations.
1. Persistent HOT pixels are removed by comparing to the chip mean.
2. Flickering WARM pixels are removed by comparing to the cell mean.
3. In faint areas (zero bgd), flickering pixels are removed with a
cutoff threshold.
Hints:
Choose cell size and thresholds based on the expected background and the PSF.
Use the DIRTYSIS option to examine the anomalous pixel spectra.
Try a multiple pass clean:
Choose a PHA cut to optimize the S/N of the flickering pixels,
then a broad band clean.
Be suspicious of extended source cleans.
For very bright sources you may need to turn off the iteration option.
See the help page for further info (fhelp cleansis)
Poisson clean cell size : 5
Poisson probability threshold : 0.575E-05
Zero Bgd Cutoff threshold (>) : 3
Iterate : F
Dirtysis : F
Minimum PHA value (inclusive) : 0
Maximum PHA value (inclusive) : 4095
open output file: ad45016000s000202m.drk
reading data file: event.tmp
copying primary header to output file...
making chip image...
Total counts in chip images : 349
copy bad pix array...
cleaning chip # 0
cleaning chip # 1
Hot pixels & counts : 5 318
Flickering pixels iter, pixels & cnts : 1 1 5
cleaning chip # 2
cleaning chip # 3
Number of pixels rejected : 6
Number of (internal) image counts : 349
Number of image cts rejected (N, %) : 32392.55
By chip : 0 1 2 3
Pixels rejected : 0 6 0 0
Image counts : 0 349 0 0
Image cts rejected: 0 323 0 0
Image cts rej (%) : 0.00 92.55 0.00 0.00
filtering data...
Total counts : 0 349 0 0
Total cts rejected: 0 323 0 0
Total cts rej (%) : 0.00 92.55 0.00 0.00
Number of clean counts accepted : 26
writing history cards...
copying extensions...
writing out hot pixs...
Number of rejected pixels : 6
updating NEVENTS keywords...
closing data file...
closing clean file...
-> Extracting bright and dark Earth events from ad45016000s000212m.unf
CLEANSIS_V1.6
allocating image arrays...
PROGRAM TO MAKE AN SIS SCIENCE FILE CLEANED OF ANOMALOUS PIXELS.
* Anomalous pixels may consist of at least two populations.
1. Persistent HOT pixels are removed by comparing to the chip mean.
2. Flickering WARM pixels are removed by comparing to the cell mean.
3. In faint areas (zero bgd), flickering pixels are removed with a
cutoff threshold.
Hints:
Choose cell size and thresholds based on the expected background and the PSF.
Use the DIRTYSIS option to examine the anomalous pixel spectra.
Try a multiple pass clean:
Choose a PHA cut to optimize the S/N of the flickering pixels,
then a broad band clean.
Be suspicious of extended source cleans.
For very bright sources you may need to turn off the iteration option.
See the help page for further info (fhelp cleansis)
Poisson clean cell size : 5
Poisson probability threshold : 0.575E-05
Zero Bgd Cutoff threshold (>) : 3
Iterate : F
Dirtysis : F
Minimum PHA value (inclusive) : 0
Maximum PHA value (inclusive) : 4095
open output file: ad45016000s000212m.drk
reading data file: event.tmp
copying primary header to output file...
making chip image...
Total counts in chip images : 353
copy bad pix array...
cleaning chip # 0
cleaning chip # 1
Hot pixels & counts : 5 318
Flickering pixels iter, pixels & cnts : 1 1 5
cleaning chip # 2
cleaning chip # 3
Number of pixels rejected : 6
Number of (internal) image counts : 353
Number of image cts rejected (N, %) : 32391.50
By chip : 0 1 2 3
Pixels rejected : 0 6 0 0
Image counts : 0 353 0 0
Image cts rejected: 0 323 0 0
Image cts rej (%) : 0.00 91.50 0.00 0.00
filtering data...
Total counts : 0 353 0 0
Total cts rejected: 0 323 0 0
Total cts rej (%) : 0.00 91.50 0.00 0.00
Number of clean counts accepted : 30
writing history cards...
copying extensions...
writing out hot pixs...
Number of rejected pixels : 6
updating NEVENTS keywords...
closing data file...
closing clean file...
-> Extracting bright and dark Earth events from ad45016000s000302l.unf
CLEANSIS_V1.6
allocating image arrays...
PROGRAM TO MAKE AN SIS SCIENCE FILE CLEANED OF ANOMALOUS PIXELS.
* Anomalous pixels may consist of at least two populations.
1. Persistent HOT pixels are removed by comparing to the chip mean.
2. Flickering WARM pixels are removed by comparing to the cell mean.
3. In faint areas (zero bgd), flickering pixels are removed with a
cutoff threshold.
Hints:
Choose cell size and thresholds based on the expected background and the PSF.
Use the DIRTYSIS option to examine the anomalous pixel spectra.
Try a multiple pass clean:
Choose a PHA cut to optimize the S/N of the flickering pixels,
then a broad band clean.
Be suspicious of extended source cleans.
For very bright sources you may need to turn off the iteration option.
See the help page for further info (fhelp cleansis)
Poisson clean cell size : 5
Poisson probability threshold : 0.575E-05
Zero Bgd Cutoff threshold (>) : 3
Iterate : F
Dirtysis : F
Minimum PHA value (inclusive) : 0
Maximum PHA value (inclusive) : 4095
open output file: ad45016000s000302l.drk
reading data file: event.tmp
copying primary header to output file...
making chip image...
Total counts in chip images : 3056
copy bad pix array...
cleaning chip # 0
cleaning chip # 1
Hot pixels & counts : 5 2814
Flickering pixels iter, pixels & cnts : 1 5 23
cleaning chip # 2
cleaning chip # 3
Number of pixels rejected : 10
Number of (internal) image counts : 3056
Number of image cts rejected (N, %) : 283792.83
By chip : 0 1 2 3
Pixels rejected : 0 10 0 0
Image counts : 0 3056 0 0
Image cts rejected: 0 2837 0 0
Image cts rej (%) : 0.00 92.83 0.00 0.00
filtering data...
Total counts : 0 3056 0 0
Total cts rejected: 0 2837 0 0
Total cts rej (%) : 0.00 92.83 0.00 0.00
Number of clean counts accepted : 219
writing history cards...
copying extensions...
writing out hot pixs...
Number of rejected pixels : 10
updating NEVENTS keywords...
closing data file...
closing clean file...
-> Extracting bright and dark Earth events from ad45016000s000312l.unf
CLEANSIS_V1.6
allocating image arrays...
PROGRAM TO MAKE AN SIS SCIENCE FILE CLEANED OF ANOMALOUS PIXELS.
* Anomalous pixels may consist of at least two populations.
1. Persistent HOT pixels are removed by comparing to the chip mean.
2. Flickering WARM pixels are removed by comparing to the cell mean.
3. In faint areas (zero bgd), flickering pixels are removed with a
cutoff threshold.
Hints:
Choose cell size and thresholds based on the expected background and the PSF.
Use the DIRTYSIS option to examine the anomalous pixel spectra.
Try a multiple pass clean:
Choose a PHA cut to optimize the S/N of the flickering pixels,
then a broad band clean.
Be suspicious of extended source cleans.
For very bright sources you may need to turn off the iteration option.
See the help page for further info (fhelp cleansis)
Poisson clean cell size : 5
Poisson probability threshold : 0.575E-05
Zero Bgd Cutoff threshold (>) : 3
Iterate : F
Dirtysis : F
Minimum PHA value (inclusive) : 0
Maximum PHA value (inclusive) : 4095
open output file: ad45016000s000312l.drk
reading data file: event.tmp
copying primary header to output file...
making chip image...
Total counts in chip images : 3109
copy bad pix array...
cleaning chip # 0
cleaning chip # 1
Hot pixels & counts : 5 2814
Flickering pixels iter, pixels & cnts : 1 5 23
cleaning chip # 2
cleaning chip # 3
Number of pixels rejected : 10
Number of (internal) image counts : 3109
Number of image cts rejected (N, %) : 283791.25
By chip : 0 1 2 3
Pixels rejected : 0 10 0 0
Image counts : 0 3109 0 0
Image cts rejected: 0 2837 0 0
Image cts rej (%) : 0.00 91.25 0.00 0.00
filtering data...
Total counts : 0 3109 0 0
Total cts rejected: 0 2837 0 0
Total cts rej (%) : 0.00 91.25 0.00 0.00
Number of clean counts accepted : 272
writing history cards...
copying extensions...
writing out hot pixs...
Number of rejected pixels : 10
updating NEVENTS keywords...
closing data file...
closing clean file...
-> Extracting bright and dark Earth events from ad45016000s100102h.unf
CLEANSIS_V1.6
allocating image arrays...
PROGRAM TO MAKE AN SIS SCIENCE FILE CLEANED OF ANOMALOUS PIXELS.
* Anomalous pixels may consist of at least two populations.
1. Persistent HOT pixels are removed by comparing to the chip mean.
2. Flickering WARM pixels are removed by comparing to the cell mean.
3. In faint areas (zero bgd), flickering pixels are removed with a
cutoff threshold.
Hints:
Choose cell size and thresholds based on the expected background and the PSF.
Use the DIRTYSIS option to examine the anomalous pixel spectra.
Try a multiple pass clean:
Choose a PHA cut to optimize the S/N of the flickering pixels,
then a broad band clean.
Be suspicious of extended source cleans.
For very bright sources you may need to turn off the iteration option.
See the help page for further info (fhelp cleansis)
Poisson clean cell size : 5
Poisson probability threshold : 0.575E-05
Zero Bgd Cutoff threshold (>) : 3
Iterate : F
Dirtysis : F
Minimum PHA value (inclusive) : 0
Maximum PHA value (inclusive) : 4095
open output file: ad45016000s100102h.drk
reading data file: event.tmp
copying primary header to output file...
making chip image...
Total counts in chip images : 1153
copy bad pix array...
cleaning chip # 0
cleaning chip # 1
cleaning chip # 2
cleaning chip # 3
Hot pixels & counts : 11 1115
Flickering pixels iter, pixels & cnts : 1 1 6
Number of pixels rejected : 12
Number of (internal) image counts : 1153
Number of image cts rejected (N, %) : 112197.22
By chip : 0 1 2 3
Pixels rejected : 0 0 0 12
Image counts : 0 0 0 1153
Image cts rejected: 0 0 0 1121
Image cts rej (%) : 0.00 0.00 0.00 97.22
filtering data...
Total counts : 0 0 0 1153
Total cts rejected: 0 0 0 1121
Total cts rej (%) : 0.00 0.00 0.00 97.22
Number of clean counts accepted : 32
writing history cards...
copying extensions...
writing out hot pixs...
Number of rejected pixels : 12
updating NEVENTS keywords...
closing data file...
closing clean file...
-> Extracting bright and dark Earth events from ad45016000s100112h.unf
CLEANSIS_V1.6
allocating image arrays...
PROGRAM TO MAKE AN SIS SCIENCE FILE CLEANED OF ANOMALOUS PIXELS.
* Anomalous pixels may consist of at least two populations.
1. Persistent HOT pixels are removed by comparing to the chip mean.
2. Flickering WARM pixels are removed by comparing to the cell mean.
3. In faint areas (zero bgd), flickering pixels are removed with a
cutoff threshold.
Hints:
Choose cell size and thresholds based on the expected background and the PSF.
Use the DIRTYSIS option to examine the anomalous pixel spectra.
Try a multiple pass clean:
Choose a PHA cut to optimize the S/N of the flickering pixels,
then a broad band clean.
Be suspicious of extended source cleans.
For very bright sources you may need to turn off the iteration option.
See the help page for further info (fhelp cleansis)
Poisson clean cell size : 5
Poisson probability threshold : 0.575E-05
Zero Bgd Cutoff threshold (>) : 3
Iterate : F
Dirtysis : F
Minimum PHA value (inclusive) : 0
Maximum PHA value (inclusive) : 4095
open output file: ad45016000s100112h.drk
reading data file: event.tmp
copying primary header to output file...
making chip image...
Total counts in chip images : 1156
copy bad pix array...
cleaning chip # 0
cleaning chip # 1
cleaning chip # 2
cleaning chip # 3
Hot pixels & counts : 11 1115
Flickering pixels iter, pixels & cnts : 1 1 6
Number of pixels rejected : 12
Number of (internal) image counts : 1156
Number of image cts rejected (N, %) : 112196.97
By chip : 0 1 2 3
Pixels rejected : 0 0 0 12
Image counts : 0 0 0 1156
Image cts rejected: 0 0 0 1121
Image cts rej (%) : 0.00 0.00 0.00 96.97
filtering data...
Total counts : 0 0 0 1156
Total cts rejected: 0 0 0 1121
Total cts rej (%) : 0.00 0.00 0.00 96.97
Number of clean counts accepted : 35
writing history cards...
copying extensions...
writing out hot pixs...
Number of rejected pixels : 12
updating NEVENTS keywords...
closing data file...
closing clean file...
-> Extracting bright and dark Earth events from ad45016000s100202m.unf
CLEANSIS_V1.6
allocating image arrays...
PROGRAM TO MAKE AN SIS SCIENCE FILE CLEANED OF ANOMALOUS PIXELS.
* Anomalous pixels may consist of at least two populations.
1. Persistent HOT pixels are removed by comparing to the chip mean.
2. Flickering WARM pixels are removed by comparing to the cell mean.
3. In faint areas (zero bgd), flickering pixels are removed with a
cutoff threshold.
Hints:
Choose cell size and thresholds based on the expected background and the PSF.
Use the DIRTYSIS option to examine the anomalous pixel spectra.
Try a multiple pass clean:
Choose a PHA cut to optimize the S/N of the flickering pixels,
then a broad band clean.
Be suspicious of extended source cleans.
For very bright sources you may need to turn off the iteration option.
See the help page for further info (fhelp cleansis)
Poisson clean cell size : 5
Poisson probability threshold : 0.575E-05
Zero Bgd Cutoff threshold (>) : 3
Iterate : F
Dirtysis : F
Minimum PHA value (inclusive) : 0
Maximum PHA value (inclusive) : 4095
open output file: ad45016000s100202m.drk
reading data file: event.tmp
copying primary header to output file...
making chip image...
Total counts in chip images : 1085
copy bad pix array...
cleaning chip # 0
cleaning chip # 1
cleaning chip # 2
cleaning chip # 3
Hot pixels & counts : 9 1045
Flickering pixels iter, pixels & cnts : 1 1 9
Number of pixels rejected : 10
Number of (internal) image counts : 1085
Number of image cts rejected (N, %) : 105497.14
By chip : 0 1 2 3
Pixels rejected : 0 0 0 10
Image counts : 0 0 0 1085
Image cts rejected: 0 0 0 1054
Image cts rej (%) : 0.00 0.00 0.00 97.14
filtering data...
Total counts : 0 0 0 1085
Total cts rejected: 0 0 0 1054
Total cts rej (%) : 0.00 0.00 0.00 97.14
Number of clean counts accepted : 31
writing history cards...
copying extensions...
writing out hot pixs...
Number of rejected pixels : 10
updating NEVENTS keywords...
closing data file...
closing clean file...
-> Extracting bright and dark Earth events from ad45016000s100212m.unf
CLEANSIS_V1.6
allocating image arrays...
PROGRAM TO MAKE AN SIS SCIENCE FILE CLEANED OF ANOMALOUS PIXELS.
* Anomalous pixels may consist of at least two populations.
1. Persistent HOT pixels are removed by comparing to the chip mean.
2. Flickering WARM pixels are removed by comparing to the cell mean.
3. In faint areas (zero bgd), flickering pixels are removed with a
cutoff threshold.
Hints:
Choose cell size and thresholds based on the expected background and the PSF.
Use the DIRTYSIS option to examine the anomalous pixel spectra.
Try a multiple pass clean:
Choose a PHA cut to optimize the S/N of the flickering pixels,
then a broad band clean.
Be suspicious of extended source cleans.
For very bright sources you may need to turn off the iteration option.
See the help page for further info (fhelp cleansis)
Poisson clean cell size : 5
Poisson probability threshold : 0.575E-05
Zero Bgd Cutoff threshold (>) : 3
Iterate : F
Dirtysis : F
Minimum PHA value (inclusive) : 0
Maximum PHA value (inclusive) : 4095
open output file: ad45016000s100212m.drk
reading data file: event.tmp
copying primary header to output file...
making chip image...
Total counts in chip images : 1085
copy bad pix array...
cleaning chip # 0
cleaning chip # 1
cleaning chip # 2
cleaning chip # 3
Hot pixels & counts : 9 1045
Flickering pixels iter, pixels & cnts : 1 1 9
Number of pixels rejected : 10
Number of (internal) image counts : 1085
Number of image cts rejected (N, %) : 105497.14
By chip : 0 1 2 3
Pixels rejected : 0 0 0 10
Image counts : 0 0 0 1085
Image cts rejected: 0 0 0 1054
Image cts rej (%) : 0.00 0.00 0.00 97.14
filtering data...
Total counts : 0 0 0 1085
Total cts rejected: 0 0 0 1054
Total cts rej (%) : 0.00 0.00 0.00 97.14
Number of clean counts accepted : 31
writing history cards...
copying extensions...
writing out hot pixs...
Number of rejected pixels : 10
updating NEVENTS keywords...
closing data file...
closing clean file...
-> Extracting bright and dark Earth events from ad45016000s100302l.unf
CLEANSIS_V1.6
allocating image arrays...
PROGRAM TO MAKE AN SIS SCIENCE FILE CLEANED OF ANOMALOUS PIXELS.
* Anomalous pixels may consist of at least two populations.
1. Persistent HOT pixels are removed by comparing to the chip mean.
2. Flickering WARM pixels are removed by comparing to the cell mean.
3. In faint areas (zero bgd), flickering pixels are removed with a
cutoff threshold.
Hints:
Choose cell size and thresholds based on the expected background and the PSF.
Use the DIRTYSIS option to examine the anomalous pixel spectra.
Try a multiple pass clean:
Choose a PHA cut to optimize the S/N of the flickering pixels,
then a broad band clean.
Be suspicious of extended source cleans.
For very bright sources you may need to turn off the iteration option.
See the help page for further info (fhelp cleansis)
Poisson clean cell size : 5
Poisson probability threshold : 0.575E-05
Zero Bgd Cutoff threshold (>) : 3
Iterate : F
Dirtysis : F
Minimum PHA value (inclusive) : 0
Maximum PHA value (inclusive) : 4095
open output file: ad45016000s100302l.drk
reading data file: event.tmp
copying primary header to output file...
making chip image...
Total counts in chip images : 6847
copy bad pix array...
cleaning chip # 0
cleaning chip # 1
cleaning chip # 2
cleaning chip # 3
Hot pixels & counts : 10 6661
Flickering pixels iter, pixels & cnts : 1 4 37
Number of pixels rejected : 14
Number of (internal) image counts : 6847
Number of image cts rejected (N, %) : 669897.82
By chip : 0 1 2 3
Pixels rejected : 0 0 0 14
Image counts : 0 0 0 6847
Image cts rejected: 0 0 0 6698
Image cts rej (%) : 0.00 0.00 0.00 97.82
filtering data...
Total counts : 0 0 0 6847
Total cts rejected: 0 0 0 6698
Total cts rej (%) : 0.00 0.00 0.00 97.82
Number of clean counts accepted : 149
writing history cards...
copying extensions...
writing out hot pixs...
Number of rejected pixels : 14
updating NEVENTS keywords...
closing data file...
closing clean file...
-> Extracting bright and dark Earth events from ad45016000s100312l.unf
CLEANSIS_V1.6
allocating image arrays...
PROGRAM TO MAKE AN SIS SCIENCE FILE CLEANED OF ANOMALOUS PIXELS.
* Anomalous pixels may consist of at least two populations.
1. Persistent HOT pixels are removed by comparing to the chip mean.
2. Flickering WARM pixels are removed by comparing to the cell mean.
3. In faint areas (zero bgd), flickering pixels are removed with a
cutoff threshold.
Hints:
Choose cell size and thresholds based on the expected background and the PSF.
Use the DIRTYSIS option to examine the anomalous pixel spectra.
Try a multiple pass clean:
Choose a PHA cut to optimize the S/N of the flickering pixels,
then a broad band clean.
Be suspicious of extended source cleans.
For very bright sources you may need to turn off the iteration option.
See the help page for further info (fhelp cleansis)
Poisson clean cell size : 5
Poisson probability threshold : 0.575E-05
Zero Bgd Cutoff threshold (>) : 3
Iterate : F
Dirtysis : F
Minimum PHA value (inclusive) : 0
Maximum PHA value (inclusive) : 4095
open output file: ad45016000s100312l.drk
reading data file: event.tmp
copying primary header to output file...
making chip image...
Total counts in chip images : 6869
copy bad pix array...
cleaning chip # 0
cleaning chip # 1
cleaning chip # 2
cleaning chip # 3
Hot pixels & counts : 10 6661
Flickering pixels iter, pixels & cnts : 1 4 37
Number of pixels rejected : 14
Number of (internal) image counts : 6869
Number of image cts rejected (N, %) : 669897.51
By chip : 0 1 2 3
Pixels rejected : 0 0 0 14
Image counts : 0 0 0 6869
Image cts rejected: 0 0 0 6698
Image cts rej (%) : 0.00 0.00 0.00 97.51
filtering data...
Total counts : 0 0 0 6869
Total cts rejected: 0 0 0 6698
Total cts rej (%) : 0.00 0.00 0.00 97.51
Number of clean counts accepted : 171
writing history cards...
copying extensions...
writing out hot pixs...
Number of rejected pixels : 14
updating NEVENTS keywords...
closing data file...
closing clean file...
-> Extracting bright and dark Earth events from ad45016000g200170m.unfOffset of 213408004.000000 from 1993-01-01 00:00:00 is date and time (including leapseconds) = 1999-10-07 00:00:00.00000 Modified Julian Day = 51458.000000000000000-> leapsec.fits already present in current directory
Offset of 197078404.000000 from 1993-01-01 00:00:00 is date and time (including leapseconds) = 1999-04-01 00:00:00.00000 Modified Julian Day = 51269.000000000000000-> leapsec.fits already present in current directory
Offset of 150000000.000000 from 1993-01-01 00:00:00 is date and time (including leapseconds) = 1997-10-03 02:39:56.00000 Modified Julian Day = 50724.111064814816928
50 1136 1978 704 3969 86084 88
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Doing inventory of all files