Processing Job Log for Sequence 33012010, version 005

This is the complete and detailed record of how this sequence was processed.

The following information is also available:



Processing started ( 13:30:02 )


Fetching and uncompressing telemetry, attitude and orbit files ( 13:30:04 )

-> Fetching ft960129_1730.2300.Z
-> Uncompressing ft960129_1730.2300.Z
-> Checking if column TIME in ft960129_1730.2300 is in order
-> Standard Output From FTOOL cktime:
 
Time column is TIME ORDERED
-> Fetching fa960129_1730.2300.Z
-> Uncompressing fa960129_1730.2300.Z
-> Fetching the latest orbit file
-> Fetching frf.orbit.214

Determine nominal aspect point for the observation ( 13:30:55 )

-> Running attitude FTOOL on merged attitude file
-> Standard Output From FTOOL attitude:
ATTITUDE_V0.9j
 
   reading attitude file:./merged.tmp
   open asc  output file:out.tmp
 
 AVERAGE ASPECT AND OFFSET FOR THIS ATTITUDE FILE:
 
 Attitude file start and stop ascatime :  97090214.246900  97110043.188700
 Data     file start and stop ascatime :  97090214.246900  97110043.188700
 Aspecting run start and stop ascatime :  97090214.247023  97110043.188594
 
 
 
 Time interval averaged over (seconds) :     19828.941572
 Total pointing and manuver time (sec) :     14101.482422      5727.487305
 
 Mean boresight Euler angles :     44.203007      70.423103     200.114571
 
                                    RA             DEC         SUN ANGLE
 
 Mean solar position   (deg) :    310.61         -18.22
 Mean aberration    (arcsec) :      3.07           1.84
 
 Mean sat X-axis       (deg) :    271.747436      62.217737      86.09
 Mean sat Y-axis       (deg) :    321.199099     -18.906129      10.06
 Mean sat Z-axis       (deg) :     44.203007      19.576898      99.26
 
                      RA            DEC            ROLL          OFFSET
                    (deg)          (deg)          (deg)         (arcmin)
 
 Average            44.000935      19.365934     110.181831       0.031034
 Minimum            43.999100      19.364946     110.175453       0.000000
 Maximum            44.021671      19.382689     110.216080       1.483477
 Sigma (RMS)         0.000049       0.000015       0.004482       0.023302
 
 Number of ASPECT records processed =      12902
 
 Aspecting to RA/DEC                   :      44.00093460      19.36593437
    closing output   file...
    closing attitude file...

E2 in aspecting: Error from attitude. Exit code=0

-> Standard Error Output From FTOOL attitude
ATTITUDE_V0.9j :  Detected gap > 15min in attitude file:    97091509.743114
ATTITUDE_V0.9j : Detected gap > 15min in attitude file:
ATTITUDE_V0.9j : Detected time value of zero in attitude file:
ATTITUDE_V0.9j : aspect is suspect: result may not be valid
-> Par file from FTOOL attitude
attitude,s,h,"merged.tmp",,,"Input ASCA attitude filename"
attpath,s,h,"./",,,"Path to attitude file or DEFAULT"
outfile,s,h,"out.tmp",,,"Output file name or NONE or DEFAULT"
pointing,s,h,"ATT",,,"Pointing from: ATT file mean or USER input"
ranom,r,h,,,,"Input aspect RA  nominal (if pointing = USER)"
decnom,r,h,,,,"Input aspect DEC nominal (if pointing = USER)"
atimecol,s,h,"TIME",,,"Attitude file TIME column name"
qcol,s,h,"QPARAM",,,"Attitude file quaternion column name"
qstat,s,h,"SENSOR",,,"Attitude file quality column name"
verbose,b,h,yes,,,"Write informational messages to screen?"
summary,b,h,no,,,"Write one line summary to screen?"
acmflag,b,h,yes,,,"Exclude manuver time from mean calculation?"
defATTpath,s,h,"./",,,"DEFAULT path to ATTITUDE file"
slewmax,r,h,0.03,,,"Maximum pointing slew rate (deg/sec),if acmflag=yes"
valid,b,h,yes,,,"Is this data valid?"
euler1,r,h,     44.2030,,,"Computed mean Euler1 angle for file (deg)"
euler2,r,h,     70.4231,,,"Computed mean Euler2 angle for file (deg)"
euler3,r,h,     200.115,,,"Computed mean Euler3 angle for file (deg)"
ra_avg,r,h,     44.0009,,,"Computed mean RA for file (degrees)"
dec_avg,r,h,     19.3659,,,"Computed mean DEC for file (degrees)"
roll_avg,r,h,     110.182,,,"Computed mean ROLL for file (degrees)"
offset_avg,r,h,     3.10340E-02,,,"Computed mean OFFSET for file (arcmin)"
ra_sig,r,h,     4.92686E-05,,,"Computed mean RA RMS for file (degrees)"
dec_sig,r,h,     1.51782E-05,,,"Computed mean DEC RMS for file (degrees)"
roll_sig,r,h,     4.48154E-03,,,"Computed mean ROLL RMS file (degrees)"
offset_sig,r,h,     2.33017E-02,,,"Computed mean OFFSET RMS for file (arcmin)"
mode,s,h,"ql",,,""
-> Standard Output From STOOL checkatt:
  
 Opening file: ./out.tmp                                                       
  
  ***************** Observation Info ******************
  
  RA (J2000 deg):   44.001 DEC:   19.366
  
  START TIME: SC  97090214.2470 = UT 29/01/96 17:30:14      
  
  ****** Definition of Attitude SENSOR Bit Flags ******
  
 Sensors used in the attitude determination and attitude control mode  
                                 1: USED,   0: NOT USED                
  
 B0:STT-A, B1:STT-B, B2:NSAS,  B3:GAS,    B4:SSAS-SA, B5:SSAS-SB,      
 B6:IRU-X, B7:IRU-Y, B8:IRU-Z, B9:IRU-S1, B10:IRU-S2,                  
 B11: Attitude control mode    1: coarse, 0: fine                      
 B12: Sun presence             1: day,    0: night                     
 B13: STT-A earth occultation  1: earth occultation, 0: no occultation 
 B14: STT-B earth occultation  1: earth occultation, 0: no occultation 
 B16,17,18: STT-A track stars no.1,2,3,     1: USED, 0: NOT USED       
 B19,20,21: STT-B track stars no.1,2,3,     1: USED, 0: NOT USED       
 B22,23: always 0                                                      
  
  ******** Attitude File Reconstruction Summary *******
  
                                    S S N G S S I I I I I A S S S S S
                                    T T S A S S R R R R R C U T T T T
                                    T T A S A A U U U U U M N T T T T
                                    - - S . A A - - - - - . . - - - -
                                    A B . . - - X Y Z S S . . A B A B
                                    . . . . S S . . . 1 2 . . O O S S
     offset_time separation sensor  . . . . A B . . . . . . . C C T T
        (sec)     (arcmin)          . . . . . . . . . . . . . C C R R
  
                             BIT:   0 1 2 3 4 5 6 7 8 9 A B C D E
  
       4.000101      0.006   2603   1 1 0 0 0 0 0 0 0 1 1 0 0 1 0 0 0
    3167.990723      0.024   2A03   1 1 0 0 0 0 0 0 0 1 0 1 0 1 0 0 0
    5083.985352      0.031 DC20C3   1 1 0 0 0 0 1 1 0 0 0 0 0 1 0 4 3
    8919.973633      0.033   2A03   1 1 0 0 0 0 0 0 0 1 0 1 0 1 0 0 0
   10843.967773      0.000 DC20C3   1 1 0 0 0 0 1 1 0 0 0 0 0 1 0 4 3
   14669.957031      0.030   2A03   1 1 0 0 0 0 0 0 0 1 0 1 0 1 0 0 0
   16603.951172      0.073 DC20C3   1 1 0 0 0 0 1 1 0 0 0 0 0 1 0 4 3
   19828.441406      1.413   3603   1 1 0 0 0 0 0 0 0 1 1 0 1 1 0 0 0
   19828.941406      1.483   3603   1 1 0 0 0 0 0 0 0 1 1 0 1 1 0 0 0
  
  Attitude  Records:   12902
  Attitude    Steps:   9
  
  Maneuver ACM time:     5727.50 sec
  Pointed  ACM time:     14101.5 sec
  
-> Calculating aspect point
-> Output from aspect:
99 99 count=41 sum1=1812.28 sum2=2887.3 sum3=8204.67
99 100 count=1987 sum1=87829.4 sum2=139931 sum3=397627
100 99 count=1362 sum1=60204.5 sum2=95914.8 sum3=272556
100 100 count=9509 sum1=420328 sum2=669653 sum3=1.90289e+06
101 98 count=1 sum1=44.222 sum2=70.406 sum3=200.149
102 98 count=1 sum1=44.224 sum2=70.41 sum3=200.145
0 out of 12901 points outside bin structure
-> Euler angles: 44.203, 70.423, 200.114
-> RA=44.0009 Dec=19.3660 Roll=-249.819
-> Galactic coordinates Lii=159.267791 Bii=-34.571266
-> Running fixatt on fa960129_1730.2300
-> Standard Output From STOOL fixatt:
Interpolating 3 records in time interval 9.711e+07 - 9.711e+07

E1 in aspecting: Error from fixatt. Exit code=0

-> Standard Error Output From STOOL fixatt
Warning: deleting invalid TIME entry 9.711e+07 in row 12904
Warning: deleting invalid TIME entry 9.711e+07 in row 12905
Warning: deleting invalid TIME entry 9.711e+07 in row 12906
Warning: deleting invalid TIME entry 9.711e+07 in row 12907

Running frfread on telemetry files ( 13:31:52 )

-> Running frfread3.032 on the following telemetry files:
frf_directory,s,h,"./",,,"frf directory"
frf_file,s,h,"ft960129_1730.2300",,,"frf telemetry file"
-> Standard Output From FTOOL frfread:
Frfread version 3.00 patch 32
ASCA format
Telemetry file: ft960129_1730.2300
Initial mode = 1  (Faint)
Initial value for dummy = 0
Initial datamode = 0  (Observation)
Initial sis = 0
Initial bit_rate = 2
Reading all superframes
reading PH mode
reading PCAL mode
reading MPCmode
No mode = 0
Faint = 206528
Bright = 0
Fast = 0
Frame = 0
Dark frame = 0
Histogram = 0
Integration = 0
PH = 206528
MPC = 0
PCAL = 0
Memory Check = 0
Number of superframes = 3248
no. of SIS events found = 112791
-> Standard Error Output From FTOOL frfread
coordinate error 232 446
coordinate error 0 0
coordinate error 0 3
coordinate error 6 0
coordinate error 0 0
coordinate error 0 12
coordinate error 0 0
coordinate error 12 0
coordinate error 192 0
coordinate error 0 0
coordinate error 0 0
coordinate error 0 0
coordinate error 0 0
coordinate error 0 192
coordinate error 0 24
coordinate error 0 0
coordinate error 24 0
coordinate error 0 0
coordinate error 0 0
coordinate error 0 384
coordinate error 0 0
coordinate error 0 0
coordinate error 0 192
coordinate error 0 0
coordinate error 24 0
-> Removing the following files with NEVENTS=0
ft960129_1730_2300G200370H.fits
ft960129_1730_2300G201170M.fits
ft960129_1730_2300G201270M.fits
ft960129_1730_2300G201370M.fits
ft960129_1730_2300G201470M.fits
ft960129_1730_2300G202270H.fits
ft960129_1730_2300G202370L.fits
ft960129_1730_2300G202470L.fits
ft960129_1730_2300G300770H.fits
ft960129_1730_2300G301370H.fits
ft960129_1730_2300G301470H.fits
ft960129_1730_2300G301670M.fits
ft960129_1730_2300G301770M.fits
ft960129_1730_2300G301870M.fits
ft960129_1730_2300G301970M.fits
ft960129_1730_2300G302870H.fits
ft960129_1730_2300G302970H.fits
ft960129_1730_2300G303070L.fits
ft960129_1730_2300G303170L.fits
ft960129_1730_2300G303570H.fits
ft960129_1730_2300S000701M.fits
ft960129_1730_2300S001601L.fits
ft960129_1730_2300S100601H.fits
ft960129_1730_2300S100701H.fits
ft960129_1730_2300S101101M.fits
ft960129_1730_2300S102001L.fits
-> Checking for empty GTI extensions
-> Checking housekeeping files for valid TSTART and TSTOP
-> Appending ALLGTI extensions to housekeeping files
-> Merging GTIs from the following files:
ft960129_1730_2300S000101M.fits[3]
ft960129_1730_2300S000201H.fits[3]
ft960129_1730_2300S000301H.fits[3]
ft960129_1730_2300S000401H.fits[3]
ft960129_1730_2300S000501L.fits[3]
ft960129_1730_2300S000601M.fits[3]
ft960129_1730_2300S000801M.fits[3]
ft960129_1730_2300S000901H.fits[3]
ft960129_1730_2300S001001L.fits[3]
ft960129_1730_2300S001101M.fits[3]
ft960129_1730_2300S001201L.fits[3]
ft960129_1730_2300S001301M.fits[3]
ft960129_1730_2300S001401H.fits[3]
ft960129_1730_2300S001501L.fits[3]
ft960129_1730_2300S001701L.fits[3]
ft960129_1730_2300S001801H.fits[3]
-> Merging GTIs from the following files:
ft960129_1730_2300S100101M.fits[3]
ft960129_1730_2300S100201H.fits[3]
ft960129_1730_2300S100301H.fits[3]
ft960129_1730_2300S100401H.fits[3]
ft960129_1730_2300S100501H.fits[3]
ft960129_1730_2300S100801H.fits[3]
ft960129_1730_2300S100901L.fits[3]
ft960129_1730_2300S101001M.fits[3]
ft960129_1730_2300S101201M.fits[3]
ft960129_1730_2300S101301H.fits[3]
ft960129_1730_2300S101401L.fits[3]
ft960129_1730_2300S101501M.fits[3]
ft960129_1730_2300S101601L.fits[3]
ft960129_1730_2300S101701M.fits[3]
ft960129_1730_2300S101801H.fits[3]
ft960129_1730_2300S101901L.fits[3]
ft960129_1730_2300S102101L.fits[3]
ft960129_1730_2300S102201H.fits[3]
-> Merging GTIs from the following files:
ft960129_1730_2300G200170M.fits[3]
ft960129_1730_2300G200270H.fits[3]
ft960129_1730_2300G200470H.fits[3]
ft960129_1730_2300G200570L.fits[3]
ft960129_1730_2300G200670L.fits[3]
ft960129_1730_2300G200770M.fits[3]
ft960129_1730_2300G200870H.fits[3]
ft960129_1730_2300G200970H.fits[3]
ft960129_1730_2300G201070L.fits[3]
ft960129_1730_2300G201570M.fits[3]
ft960129_1730_2300G201670M.fits[3]
ft960129_1730_2300G201770L.fits[3]
ft960129_1730_2300G201870L.fits[3]
ft960129_1730_2300G201970M.fits[3]
ft960129_1730_2300G202070H.fits[3]
ft960129_1730_2300G202170H.fits[3]
ft960129_1730_2300G202570L.fits[3]
ft960129_1730_2300G202670L.fits[3]
ft960129_1730_2300G202770H.fits[3]
ft960129_1730_2300G202870H.fits[3]
ft960129_1730_2300G202970H.fits[3]
ft960129_1730_2300G203070H.fits[3]
-> Merging GTIs from the following files:
ft960129_1730_2300G300170M.fits[3]
ft960129_1730_2300G300270H.fits[3]
ft960129_1730_2300G300370H.fits[3]
ft960129_1730_2300G300470H.fits[3]
ft960129_1730_2300G300570H.fits[3]
ft960129_1730_2300G300670H.fits[3]
ft960129_1730_2300G300870H.fits[3]
ft960129_1730_2300G300970L.fits[3]
ft960129_1730_2300G301070L.fits[3]
ft960129_1730_2300G301170M.fits[3]
ft960129_1730_2300G301270H.fits[3]
ft960129_1730_2300G301570L.fits[3]
ft960129_1730_2300G302070M.fits[3]
ft960129_1730_2300G302170M.fits[3]
ft960129_1730_2300G302270L.fits[3]
ft960129_1730_2300G302370L.fits[3]
ft960129_1730_2300G302470L.fits[3]
ft960129_1730_2300G302570L.fits[3]
ft960129_1730_2300G302670M.fits[3]
ft960129_1730_2300G302770H.fits[3]
ft960129_1730_2300G303270L.fits[3]
ft960129_1730_2300G303370L.fits[3]
ft960129_1730_2300G303470H.fits[3]
ft960129_1730_2300G303670H.fits[3]
ft960129_1730_2300G303770H.fits[3]

Merging event files from frfread ( 13:39:31 )

-> Collecting GIS2 event files by mode
-> Standard Error Output From STOOL gissortcode:
GISSORTCODE:LO:Start program
GISSORTCODE:LO:End program
-> Standard Error Output From STOOL gissortsplit:
GISSORTSPLIT:LO:Start program
GISSORTSPLIT:LO:g200170h.prelist merge count = 1 photon cnt = 2
GISSORTSPLIT:LO:g200270h.prelist merge count = 1 photon cnt = 1
GISSORTSPLIT:LO:g200370h.prelist merge count = 5 photon cnt = 4638
GISSORTSPLIT:LO:g200470h.prelist merge count = 1 photon cnt = 2
GISSORTSPLIT:LO:g200570h.prelist merge count = 1 photon cnt = 3
GISSORTSPLIT:LO:g200670h.prelist merge count = 1 photon cnt = 1
GISSORTSPLIT:LO:g200170l.prelist merge count = 1 photon cnt = 1
GISSORTSPLIT:LO:g200270l.prelist merge count = 1 photon cnt = 42
GISSORTSPLIT:LO:g200370l.prelist merge count = 3 photon cnt = 3925
GISSORTSPLIT:LO:g200470l.prelist merge count = 2 photon cnt = 329
GISSORTSPLIT:LO:g200170m.prelist merge count = 1 photon cnt = 7
GISSORTSPLIT:LO:g200270m.prelist merge count = 4 photon cnt = 2903
GISSORTSPLIT:LO:Total filenames split = 22
GISSORTSPLIT:LO:Total split file cnt = 12
GISSORTSPLIT:LO:End program
-> Creating ad33012010g200170h.unf
-> Standard Output From STOOL cmerge:
---- cmerge:  version 1.5 ----

A total of  5  fits files ...... 
Sorting files using KEY: TSTART ... 
Checking GTI overlap in input files ... 
Merging binary extension #: 1 
 1 -- ft960129_1730_2300G200270H.fits 
 2 -- ft960129_1730_2300G200470H.fits 
 3 -- ft960129_1730_2300G200870H.fits 
 4 -- ft960129_1730_2300G202070H.fits 
 5 -- ft960129_1730_2300G203070H.fits 
Merging binary extension #: 2 
 1 -- ft960129_1730_2300G200270H.fits 
 2 -- ft960129_1730_2300G200470H.fits 
 3 -- ft960129_1730_2300G200870H.fits 
 4 -- ft960129_1730_2300G202070H.fits 
 5 -- ft960129_1730_2300G203070H.fits 
Checking the output file ...
 Extention # 1 ......   OK
 Extention # 2 ......   OK
The program appears to have finished successfully! 
-> Creating ad33012010g200270l.unf
-> Standard Output From STOOL cmerge:
---- cmerge:  version 1.5 ----

A total of  3  fits files ...... 
Sorting files using KEY: TSTART ... 
Checking GTI overlap in input files ... 
Merging binary extension #: 1 
 1 -- ft960129_1730_2300G200670L.fits 
 2 -- ft960129_1730_2300G201870L.fits 
 3 -- ft960129_1730_2300G202670L.fits 
Merging binary extension #: 2 
 1 -- ft960129_1730_2300G200670L.fits 
 2 -- ft960129_1730_2300G201870L.fits 
 3 -- ft960129_1730_2300G202670L.fits 
Checking the output file ...
 Extention # 1 ......   OK
 Extention # 2 ......   OK
The program appears to have finished successfully! 
-> Creating ad33012010g200370m.unf
-> Standard Output From STOOL cmerge:
---- cmerge:  version 1.5 ----

A total of  4  fits files ...... 
Sorting files using KEY: TSTART ... 
Checking GTI overlap in input files ... 
Merging binary extension #: 1 
 1 -- ft960129_1730_2300G200170M.fits 
 2 -- ft960129_1730_2300G200770M.fits 
 3 -- ft960129_1730_2300G201670M.fits 
 4 -- ft960129_1730_2300G201970M.fits 
Merging binary extension #: 2 
 1 -- ft960129_1730_2300G200170M.fits 
 2 -- ft960129_1730_2300G200770M.fits 
 3 -- ft960129_1730_2300G201670M.fits 
 4 -- ft960129_1730_2300G201970M.fits 
Checking the output file ...
 Extention # 1 ......   OK
 Extention # 2 ......   OK
The program appears to have finished successfully! 
-> Ignoring the following files containing 000000329 events
ft960129_1730_2300G200570L.fits
ft960129_1730_2300G201770L.fits
-> Ignoring the following files containing 000000042 events
ft960129_1730_2300G202570L.fits
-> Ignoring the following files containing 000000007 events
ft960129_1730_2300G201570M.fits
-> Ignoring the following files containing 000000003 events
ft960129_1730_2300G202770H.fits
-> Ignoring the following files containing 000000002 events
ft960129_1730_2300G202970H.fits
-> Ignoring the following files containing 000000002 events
ft960129_1730_2300G200970H.fits
-> Ignoring the following files containing 000000001 events
ft960129_1730_2300G202870H.fits
-> Ignoring the following files containing 000000001 events
ft960129_1730_2300G202170H.fits
-> Ignoring the following files containing 000000001 events
ft960129_1730_2300G201070L.fits
-> Collecting GIS3 event files by mode
-> Standard Error Output From STOOL gissortcode:
GISSORTCODE:LO:Start program
GISSORTCODE:LO:End program
-> Standard Error Output From STOOL gissortsplit:
GISSORTSPLIT:LO:Start program
GISSORTSPLIT:LO:g300170h.prelist merge count = 1 photon cnt = 1
GISSORTSPLIT:LO:g300270h.prelist merge count = 7 photon cnt = 4397
GISSORTSPLIT:LO:g300370h.prelist merge count = 1 photon cnt = 4
GISSORTSPLIT:LO:g300470h.prelist merge count = 1 photon cnt = 3
GISSORTSPLIT:LO:g300570h.prelist merge count = 1 photon cnt = 1
GISSORTSPLIT:LO:g300170l.prelist merge count = 1 photon cnt = 1
GISSORTSPLIT:LO:g300270l.prelist merge count = 1 photon cnt = 37
GISSORTSPLIT:LO:g300370l.prelist merge count = 4 photon cnt = 3589
GISSORTSPLIT:LO:g300470l.prelist merge count = 2 photon cnt = 270
GISSORTSPLIT:LO:g300570l.prelist merge count = 1 photon cnt = 103
GISSORTSPLIT:LO:g300170m.prelist merge count = 1 photon cnt = 11
GISSORTSPLIT:LO:g300270m.prelist merge count = 4 photon cnt = 2867
GISSORTSPLIT:LO:Total filenames split = 25
GISSORTSPLIT:LO:Total split file cnt = 12
GISSORTSPLIT:LO:End program
-> Creating ad33012010g300170h.unf
-> Standard Output From STOOL cmerge:
---- cmerge:  version 1.5 ----

A total of  7  fits files ...... 
Sorting files using KEY: TSTART ... 
Checking GTI overlap in input files ... 
Merging binary extension #: 1 
 1 -- ft960129_1730_2300G300270H.fits 
 2 -- ft960129_1730_2300G300470H.fits 
 3 -- ft960129_1730_2300G300670H.fits 
 4 -- ft960129_1730_2300G300870H.fits 
 5 -- ft960129_1730_2300G301270H.fits 
 6 -- ft960129_1730_2300G302770H.fits 
 7 -- ft960129_1730_2300G303770H.fits 
Merging binary extension #: 2 
 1 -- ft960129_1730_2300G300270H.fits 
 2 -- ft960129_1730_2300G300470H.fits 
 3 -- ft960129_1730_2300G300670H.fits 
 4 -- ft960129_1730_2300G300870H.fits 
 5 -- ft960129_1730_2300G301270H.fits 
 6 -- ft960129_1730_2300G302770H.fits 
 7 -- ft960129_1730_2300G303770H.fits 
Checking the output file ...
 Extention # 1 ......   OK
 Extention # 2 ......   OK
The program appears to have finished successfully! 
-> Creating ad33012010g300270l.unf
-> Standard Output From STOOL cmerge:
---- cmerge:  version 1.5 ----

A total of  4  fits files ...... 
Sorting files using KEY: TSTART ... 
Checking GTI overlap in input files ... 
Merging binary extension #: 1 
 1 -- ft960129_1730_2300G301070L.fits 
 2 -- ft960129_1730_2300G302370L.fits 
 3 -- ft960129_1730_2300G302570L.fits 
 4 -- ft960129_1730_2300G303370L.fits 
Merging binary extension #: 2 
 1 -- ft960129_1730_2300G301070L.fits 
 2 -- ft960129_1730_2300G302370L.fits 
 3 -- ft960129_1730_2300G302570L.fits 
 4 -- ft960129_1730_2300G303370L.fits 
Checking the output file ...
 Extention # 1 ......   OK
 Extention # 2 ......   OK
The program appears to have finished successfully! 
-> Creating ad33012010g300370m.unf
-> Standard Output From STOOL cmerge:
---- cmerge:  version 1.5 ----

A total of  4  fits files ...... 
Sorting files using KEY: TSTART ... 
Checking GTI overlap in input files ... 
Merging binary extension #: 1 
 1 -- ft960129_1730_2300G300170M.fits 
 2 -- ft960129_1730_2300G301170M.fits 
 3 -- ft960129_1730_2300G302170M.fits 
 4 -- ft960129_1730_2300G302670M.fits 
Merging binary extension #: 2 
 1 -- ft960129_1730_2300G300170M.fits 
 2 -- ft960129_1730_2300G301170M.fits 
 3 -- ft960129_1730_2300G302170M.fits 
 4 -- ft960129_1730_2300G302670M.fits 
Checking the output file ...
 Extention # 1 ......   OK
 Extention # 2 ......   OK
The program appears to have finished successfully! 
-> Ignoring the following files containing 000000270 events
ft960129_1730_2300G300970L.fits
ft960129_1730_2300G302270L.fits
-> Ignoring the following files containing 000000103 events
ft960129_1730_2300G302470L.fits
-> Ignoring the following files containing 000000037 events
ft960129_1730_2300G303270L.fits
-> Ignoring the following files containing 000000011 events
ft960129_1730_2300G302070M.fits
-> Ignoring the following files containing 000000004 events
ft960129_1730_2300G303670H.fits
-> Ignoring the following files containing 000000003 events
ft960129_1730_2300G303470H.fits
-> Ignoring the following files containing 000000001 events
ft960129_1730_2300G300370H.fits
-> Ignoring the following files containing 000000001 events
ft960129_1730_2300G301570L.fits
-> Ignoring the following files containing 000000001 events
ft960129_1730_2300G300570H.fits
-> Collecting SIS0 event files by mode
-> Standard Error Output From STOOL sis0sortcode:
SIS0SORTCODE:LO:Start program
SIS0SORTCODE:LO:End program
-> Standard Error Output From STOOL sis0sortsplit:
SIS0SORTSPLIT:LO:Start program
SIS0SORTSPLIT:LO:s000101h.prelist merge count = 5 photon cnt = 24570
SIS0SORTSPLIT:LO:s000201h.prelist merge count = 1 photon cnt = 11
SIS0SORTSPLIT:LO:s000301l.prelist merge count = 5 photon cnt = 13576
SIS0SORTSPLIT:LO:s000401m.prelist merge count = 5 photon cnt = 12967
SIS0SORTSPLIT:LO:Total filenames split = 16
SIS0SORTSPLIT:LO:Total split file cnt = 4
SIS0SORTSPLIT:LO:End program
-> Creating ad33012010s000101h.unf
-> Standard Output From STOOL cmerge:
---- cmerge:  version 1.5 ----

A total of  5  fits files ...... 
Sorting files using KEY: TSTART ... 
Checking GTI overlap in input files ... 
Merging binary extension #: 1 
 1 -- ft960129_1730_2300S000201H.fits 
 2 -- ft960129_1730_2300S000401H.fits 
 3 -- ft960129_1730_2300S000901H.fits 
 4 -- ft960129_1730_2300S001401H.fits 
 5 -- ft960129_1730_2300S001801H.fits 
Merging binary extension #: 2 
 1 -- ft960129_1730_2300S000201H.fits 
 2 -- ft960129_1730_2300S000401H.fits 
 3 -- ft960129_1730_2300S000901H.fits 
 4 -- ft960129_1730_2300S001401H.fits 
 5 -- ft960129_1730_2300S001801H.fits 
Checking the output file ...
 Extention # 1 ......   OK
 Extention # 2 ......   OK
The program appears to have finished successfully! 
-> Creating ad33012010s000201l.unf
-> Standard Output From STOOL cmerge:
---- cmerge:  version 1.5 ----

A total of  5  fits files ...... 
Sorting files using KEY: TSTART ... 
Checking GTI overlap in input files ... 
Merging binary extension #: 1 
 1 -- ft960129_1730_2300S000501L.fits 
 2 -- ft960129_1730_2300S001001L.fits 
 3 -- ft960129_1730_2300S001201L.fits 
 4 -- ft960129_1730_2300S001501L.fits 
 5 -- ft960129_1730_2300S001701L.fits 
Merging binary extension #: 2 
 1 -- ft960129_1730_2300S000501L.fits 
 2 -- ft960129_1730_2300S001001L.fits 
 3 -- ft960129_1730_2300S001201L.fits 
 4 -- ft960129_1730_2300S001501L.fits 
 5 -- ft960129_1730_2300S001701L.fits 
Checking the output file ...
 Extention # 1 ......   OK
 Extention # 2 ......   OK
The program appears to have finished successfully! 
-> Creating ad33012010s000301m.unf
-> Standard Output From STOOL cmerge:
---- cmerge:  version 1.5 ----

A total of  5  fits files ...... 
Sorting files using KEY: TSTART ... 
Checking GTI overlap in input files ... 
Merging binary extension #: 1 
 1 -- ft960129_1730_2300S000101M.fits 
 2 -- ft960129_1730_2300S000601M.fits 
 3 -- ft960129_1730_2300S000801M.fits 
 4 -- ft960129_1730_2300S001101M.fits 
 5 -- ft960129_1730_2300S001301M.fits 
Merging binary extension #: 2 
 1 -- ft960129_1730_2300S000101M.fits 
 2 -- ft960129_1730_2300S000601M.fits 
 3 -- ft960129_1730_2300S000801M.fits 
 4 -- ft960129_1730_2300S001101M.fits 
 5 -- ft960129_1730_2300S001301M.fits 
Checking the output file ...
 Extention # 1 ......   OK
 Extention # 2 ......   OK
The program appears to have finished successfully! 
-> Ignoring the following files containing 000000011 events
ft960129_1730_2300S000301H.fits
-> Collecting SIS1 event files by mode
-> Standard Error Output From STOOL sis1sortcode:
SIS1SORTCODE:LO:Start program
SIS1SORTCODE:LO:End program
-> Standard Error Output From STOOL sis1sortsplit:
SIS1SORTSPLIT:LO:Start program
SIS1SORTSPLIT:LO:s100101h.prelist merge count = 1 photon cnt = 108
SIS1SORTSPLIT:LO:s100201h.prelist merge count = 6 photon cnt = 31457
SIS1SORTSPLIT:LO:s100301h.prelist merge count = 1 photon cnt = 40
SIS1SORTSPLIT:LO:s100401l.prelist merge count = 5 photon cnt = 15055
SIS1SORTSPLIT:LO:s100501m.prelist merge count = 5 photon cnt = 14982
SIS1SORTSPLIT:LO:Total filenames split = 18
SIS1SORTSPLIT:LO:Total split file cnt = 5
SIS1SORTSPLIT:LO:End program
-> Creating ad33012010s100101h.unf
-> Standard Output From STOOL cmerge:
---- cmerge:  version 1.5 ----

A total of  6  fits files ...... 
Sorting files using KEY: TSTART ... 
Checking GTI overlap in input files ... 
Merging binary extension #: 1 
 1 -- ft960129_1730_2300S100201H.fits 
 2 -- ft960129_1730_2300S100401H.fits 
 3 -- ft960129_1730_2300S100801H.fits 
 4 -- ft960129_1730_2300S101301H.fits 
 5 -- ft960129_1730_2300S101801H.fits 
 6 -- ft960129_1730_2300S102201H.fits 
Merging binary extension #: 2 
 1 -- ft960129_1730_2300S100201H.fits 
 2 -- ft960129_1730_2300S100401H.fits 
 3 -- ft960129_1730_2300S100801H.fits 
 4 -- ft960129_1730_2300S101301H.fits 
 5 -- ft960129_1730_2300S101801H.fits 
 6 -- ft960129_1730_2300S102201H.fits 
Checking the output file ...
 Extention # 1 ......   OK
 Extention # 2 ......   OK
The program appears to have finished successfully! 
-> Creating ad33012010s100201l.unf
-> Standard Output From STOOL cmerge:
---- cmerge:  version 1.5 ----

A total of  5  fits files ...... 
Sorting files using KEY: TSTART ... 
Checking GTI overlap in input files ... 
Merging binary extension #: 1 
 1 -- ft960129_1730_2300S100901L.fits 
 2 -- ft960129_1730_2300S101401L.fits 
 3 -- ft960129_1730_2300S101601L.fits 
 4 -- ft960129_1730_2300S101901L.fits 
 5 -- ft960129_1730_2300S102101L.fits 
Merging binary extension #: 2 
 1 -- ft960129_1730_2300S100901L.fits 
 2 -- ft960129_1730_2300S101401L.fits 
 3 -- ft960129_1730_2300S101601L.fits 
 4 -- ft960129_1730_2300S101901L.fits 
 5 -- ft960129_1730_2300S102101L.fits 
Checking the output file ...
 Extention # 1 ......   OK
 Extention # 2 ......   OK
The program appears to have finished successfully! 
-> Creating ad33012010s100301m.unf
-> Standard Output From STOOL cmerge:
---- cmerge:  version 1.5 ----

A total of  5  fits files ...... 
Sorting files using KEY: TSTART ... 
Checking GTI overlap in input files ... 
Merging binary extension #: 1 
 1 -- ft960129_1730_2300S100101M.fits 
 2 -- ft960129_1730_2300S101001M.fits 
 3 -- ft960129_1730_2300S101201M.fits 
 4 -- ft960129_1730_2300S101501M.fits 
 5 -- ft960129_1730_2300S101701M.fits 
Merging binary extension #: 2 
 1 -- ft960129_1730_2300S100101M.fits 
 2 -- ft960129_1730_2300S101001M.fits 
 3 -- ft960129_1730_2300S101201M.fits 
 4 -- ft960129_1730_2300S101501M.fits 
 5 -- ft960129_1730_2300S101701M.fits 
Checking the output file ...
 Extention # 1 ......   OK
 Extention # 2 ......   OK
The program appears to have finished successfully! 
-> Ignoring the following files containing 000000108 events
ft960129_1730_2300S100301H.fits
-> Ignoring the following files containing 000000040 events
ft960129_1730_2300S100501H.fits
-> Tar-ing together the leftover raw files
a ft960129_1730_2300G200570L.fits 43K
a ft960129_1730_2300G200970H.fits 40K
a ft960129_1730_2300G201070L.fits 40K
a ft960129_1730_2300G201570M.fits 40K
a ft960129_1730_2300G201770L.fits 43K
a ft960129_1730_2300G202170H.fits 40K
a ft960129_1730_2300G202570L.fits 40K
a ft960129_1730_2300G202770H.fits 40K
a ft960129_1730_2300G202870H.fits 40K
a ft960129_1730_2300G202970H.fits 40K
a ft960129_1730_2300G300370H.fits 40K
a ft960129_1730_2300G300570H.fits 40K
a ft960129_1730_2300G300970L.fits 43K
a ft960129_1730_2300G301570L.fits 40K
a ft960129_1730_2300G302070M.fits 40K
a ft960129_1730_2300G302270L.fits 43K
a ft960129_1730_2300G302470L.fits 43K
a ft960129_1730_2300G303270L.fits 40K
a ft960129_1730_2300G303470H.fits 40K
a ft960129_1730_2300G303670H.fits 40K
a ft960129_1730_2300S000301H.fits 40K
a ft960129_1730_2300S100301H.fits 43K
a ft960129_1730_2300S100501H.fits 40K
-> Checking OBJECT keywords in HK and event files

Converting FAINT mode files to BRIGHT and BRIGHT2 modes ( 13:44:31 )

-> Split threshold for SIS0=40, and SIS1=40
-> Fetching faintdfe.tbl
-> Calculating DFE values for ad33012010s000101h.unf with zerodef=1
-> Converting ad33012010s000101h.unf to ad33012010s000112h.unf
-> Calculating DFE values for ad33012010s000101h.unf with zerodef=2
-> Converting ad33012010s000101h.unf to ad33012010s000102h.unf
-> Generating corner pixel histogram ad33012010s000102h_1.cnr
-> Calculating DFE values for ad33012010s000201l.unf with zerodef=1
-> Converting ad33012010s000201l.unf to ad33012010s000212l.unf
-> Calculating DFE values for ad33012010s000201l.unf with zerodef=2
-> Converting ad33012010s000201l.unf to ad33012010s000202l.unf
-> Generating corner pixel histogram ad33012010s000202l_1.cnr
-> Calculating DFE values for ad33012010s000301m.unf with zerodef=1
-> Converting ad33012010s000301m.unf to ad33012010s000312m.unf
-> Calculating DFE values for ad33012010s000301m.unf with zerodef=2
-> Converting ad33012010s000301m.unf to ad33012010s000302m.unf
-> Generating corner pixel histogram ad33012010s000302m_1.cnr
-> Calculating DFE values for ad33012010s100101h.unf with zerodef=1
-> Converting ad33012010s100101h.unf to ad33012010s100112h.unf
-> Calculating DFE values for ad33012010s100101h.unf with zerodef=2
-> Converting ad33012010s100101h.unf to ad33012010s100102h.unf
-> Generating corner pixel histogram ad33012010s100102h_3.cnr
-> Calculating DFE values for ad33012010s100201l.unf with zerodef=1
-> Converting ad33012010s100201l.unf to ad33012010s100212l.unf
-> Calculating DFE values for ad33012010s100201l.unf with zerodef=2
-> Converting ad33012010s100201l.unf to ad33012010s100202l.unf
-> Generating corner pixel histogram ad33012010s100202l_3.cnr
-> Calculating DFE values for ad33012010s100301m.unf with zerodef=1
-> Converting ad33012010s100301m.unf to ad33012010s100312m.unf
-> Calculating DFE values for ad33012010s100301m.unf with zerodef=2
-> Converting ad33012010s100301m.unf to ad33012010s100302m.unf
-> Generating corner pixel histogram ad33012010s100302m_3.cnr

Creating GIS gain history file ( 13:51:02 )

-> Fetching gis_temp2gain.fits
-> Fetching leapsec.fits
-> Creating gain history file ft960129_1730_2300.ghf
-> Output from ISAS program temp2gain
temp2gain v4.2
opening ft960129_1730.2300
'ft960129_1730.2300' is successfully opened
Data Start Time is 97090211.25 (960129 173011)
Time Margin 2.0 sec included
Sync error detected in 63 th SF
Sync error detected in 99 th SF
Sync error detected in 108 th SF
Sync error detected in 231 th SF
Sync error detected in 245 th SF
Sync error detected in 283 th SF
Sync error detected in 311 th SF
Sync error detected in 324 th SF
Sync error detected in 330 th SF
Sync error detected in 1714 th SF
Sync error detected in 1722 th SF
Sync error detected in 1751 th SF
'ft960129_1730.2300' EOF detected, sf=3248
Data End Time is 97110047.19 (960129 230047)
Gain History is written in ft960129_1730_2300.ghf
-> Checking if column CAL_START in ft960129_1730_2300.ghf[1] is in order
-> Standard Output From FTOOL cktime:
 
Time column is TIME ORDERED
-> Checking if column CAL_STOP in ft960129_1730_2300.ghf[1] is in order
-> Standard Output From FTOOL cktime:
 
Time column is TIME ORDERED

Running ASCALIN on unfiltered event files ( 13:51:51 )

-> Checking if ad33012010g200170h.unf is covered by attitude file
-> Running ascalin on ad33012010g200170h.unf
-> Fetching gis2_ano_on_flf_180295.fits
-> Standard Output From FTOOL ascalin:
ASCALIN_V0.9t
 
-> Standard Error Output From FTOOL ascalin
ASCALIN_V0.9t :  Detected gap > 15min in attitude file:    97091509.743114
ASCALIN_V0.9t : Detected gap > 15min in attitude file:
-> Checking if ad33012010g200270l.unf is covered by attitude file
-> Running ascalin on ad33012010g200270l.unf
-> gis2_ano_on_flf_180295.fits already present in current directory
-> Standard Output From FTOOL ascalin:
ASCALIN_V0.9t
-> Checking if ad33012010g200370m.unf is covered by attitude file
-> Running ascalin on ad33012010g200370m.unf
-> gis2_ano_on_flf_180295.fits already present in current directory
-> Standard Output From FTOOL ascalin:
ASCALIN_V0.9t
 
-> Standard Error Output From FTOOL ascalin
ASCALIN_V0.9t :  Detected gap > 15min in attitude file:    97091509.743114
ASCALIN_V0.9t : Detected gap > 15min in attitude file:
-> Checking if ad33012010g300170h.unf is covered by attitude file
-> Running ascalin on ad33012010g300170h.unf
-> Fetching gis3_ano_on_flf_180295.fits
-> Standard Output From FTOOL ascalin:
ASCALIN_V0.9t
 
-> Standard Error Output From FTOOL ascalin
ASCALIN_V0.9t :  Detected gap > 15min in attitude file:    97091509.743114
ASCALIN_V0.9t : Detected gap > 15min in attitude file:
-> Checking if ad33012010g300270l.unf is covered by attitude file
-> Running ascalin on ad33012010g300270l.unf
-> gis3_ano_on_flf_180295.fits already present in current directory
-> Standard Output From FTOOL ascalin:
ASCALIN_V0.9t
-> Checking if ad33012010g300370m.unf is covered by attitude file
-> Running ascalin on ad33012010g300370m.unf
-> gis3_ano_on_flf_180295.fits already present in current directory
-> Standard Output From FTOOL ascalin:
ASCALIN_V0.9t
 
-> Standard Error Output From FTOOL ascalin
ASCALIN_V0.9t :  Detected gap > 15min in attitude file:    97091509.743114
ASCALIN_V0.9t : Detected gap > 15min in attitude file:
-> Checking if ad33012010s000101h.unf is covered by attitude file
-> Running ascalin on ad33012010s000101h.unf
-> Fetching sisph2pi_110397.fits
-> Fetching s0_teldef_ascalin.fits
-> Standard Output From FTOOL ascalin:
ASCALIN_V0.9t
 
-> Standard Error Output From FTOOL ascalin
ASCALIN_V0.9t :  Detected gap > 15min in attitude file:    97091509.743114
ASCALIN_V0.9t : Detected gap > 15min in attitude file:
-> Checking if ad33012010s000102h.unf is covered by attitude file
-> Running ascalin on ad33012010s000102h.unf
-> sisph2pi_110397.fits already present in current directory
-> s0_teldef_ascalin.fits already present in current directory
-> Standard Output From FTOOL ascalin:
ASCALIN_V0.9t
 
-> Standard Error Output From FTOOL ascalin
ASCALIN_V0.9t :  Detected gap > 15min in attitude file:    97091509.743114
ASCALIN_V0.9t : Detected gap > 15min in attitude file:
-> Checking if ad33012010s000112h.unf is covered by attitude file
-> Running ascalin on ad33012010s000112h.unf
-> sisph2pi_110397.fits already present in current directory
-> s0_teldef_ascalin.fits already present in current directory
-> Standard Output From FTOOL ascalin:
ASCALIN_V0.9t
 
-> Standard Error Output From FTOOL ascalin
ASCALIN_V0.9t :  Detected gap > 15min in attitude file:    97091509.743114
ASCALIN_V0.9t : Detected gap > 15min in attitude file:
-> Checking if ad33012010s000201l.unf is covered by attitude file
-> Running ascalin on ad33012010s000201l.unf
-> sisph2pi_110397.fits already present in current directory
-> s0_teldef_ascalin.fits already present in current directory
-> Standard Output From FTOOL ascalin:
ASCALIN_V0.9t
-> Checking if ad33012010s000202l.unf is covered by attitude file
-> Running ascalin on ad33012010s000202l.unf
-> sisph2pi_110397.fits already present in current directory
-> s0_teldef_ascalin.fits already present in current directory
-> Standard Output From FTOOL ascalin:
ASCALIN_V0.9t
-> Checking if ad33012010s000212l.unf is covered by attitude file
-> Running ascalin on ad33012010s000212l.unf
-> sisph2pi_110397.fits already present in current directory
-> s0_teldef_ascalin.fits already present in current directory
-> Standard Output From FTOOL ascalin:
ASCALIN_V0.9t
-> Checking if ad33012010s000301m.unf is covered by attitude file
-> Running ascalin on ad33012010s000301m.unf
-> sisph2pi_110397.fits already present in current directory
-> s0_teldef_ascalin.fits already present in current directory
-> Standard Output From FTOOL ascalin:
ASCALIN_V0.9t
 
-> Standard Error Output From FTOOL ascalin
ASCALIN_V0.9t :  Detected gap > 15min in attitude file:    97091509.743114
ASCALIN_V0.9t : Detected gap > 15min in attitude file:
-> Checking if ad33012010s000302m.unf is covered by attitude file
-> Running ascalin on ad33012010s000302m.unf
-> sisph2pi_110397.fits already present in current directory
-> s0_teldef_ascalin.fits already present in current directory
-> Standard Output From FTOOL ascalin:
ASCALIN_V0.9t
 
-> Standard Error Output From FTOOL ascalin
ASCALIN_V0.9t :  Detected gap > 15min in attitude file:    97091509.743114
ASCALIN_V0.9t : Detected gap > 15min in attitude file:
-> Checking if ad33012010s000312m.unf is covered by attitude file
-> Running ascalin on ad33012010s000312m.unf
-> sisph2pi_110397.fits already present in current directory
-> s0_teldef_ascalin.fits already present in current directory
-> Standard Output From FTOOL ascalin:
ASCALIN_V0.9t
 
-> Standard Error Output From FTOOL ascalin
ASCALIN_V0.9t :  Detected gap > 15min in attitude file:    97091509.743114
ASCALIN_V0.9t : Detected gap > 15min in attitude file:
-> Checking if ad33012010s100101h.unf is covered by attitude file
-> Running ascalin on ad33012010s100101h.unf
-> sisph2pi_110397.fits already present in current directory
-> Fetching s1_teldef_ascalin.fits
-> Standard Output From FTOOL ascalin:
ASCALIN_V0.9t
 
-> Standard Error Output From FTOOL ascalin
ASCALIN_V0.9t :  Detected gap > 15min in attitude file:    97091509.743114
ASCALIN_V0.9t : Detected gap > 15min in attitude file:
-> Checking if ad33012010s100102h.unf is covered by attitude file
-> Running ascalin on ad33012010s100102h.unf
-> sisph2pi_110397.fits already present in current directory
-> s1_teldef_ascalin.fits already present in current directory
-> Standard Output From FTOOL ascalin:
ASCALIN_V0.9t
 
-> Standard Error Output From FTOOL ascalin
ASCALIN_V0.9t :  Detected gap > 15min in attitude file:    97091509.743114
ASCALIN_V0.9t : Detected gap > 15min in attitude file:
-> Checking if ad33012010s100112h.unf is covered by attitude file
-> Running ascalin on ad33012010s100112h.unf
-> sisph2pi_110397.fits already present in current directory
-> s1_teldef_ascalin.fits already present in current directory
-> Standard Output From FTOOL ascalin:
ASCALIN_V0.9t
 
-> Standard Error Output From FTOOL ascalin
ASCALIN_V0.9t :  Detected gap > 15min in attitude file:    97091509.743114
ASCALIN_V0.9t : Detected gap > 15min in attitude file:
-> Checking if ad33012010s100201l.unf is covered by attitude file
-> Running ascalin on ad33012010s100201l.unf
-> sisph2pi_110397.fits already present in current directory
-> s1_teldef_ascalin.fits already present in current directory
-> Standard Output From FTOOL ascalin:
ASCALIN_V0.9t
-> Checking if ad33012010s100202l.unf is covered by attitude file
-> Running ascalin on ad33012010s100202l.unf
-> sisph2pi_110397.fits already present in current directory
-> s1_teldef_ascalin.fits already present in current directory
-> Standard Output From FTOOL ascalin:
ASCALIN_V0.9t
-> Checking if ad33012010s100212l.unf is covered by attitude file
-> Running ascalin on ad33012010s100212l.unf
-> sisph2pi_110397.fits already present in current directory
-> s1_teldef_ascalin.fits already present in current directory
-> Standard Output From FTOOL ascalin:
ASCALIN_V0.9t
-> Checking if ad33012010s100301m.unf is covered by attitude file
-> Running ascalin on ad33012010s100301m.unf
-> sisph2pi_110397.fits already present in current directory
-> s1_teldef_ascalin.fits already present in current directory
-> Standard Output From FTOOL ascalin:
ASCALIN_V0.9t
 
-> Standard Error Output From FTOOL ascalin
ASCALIN_V0.9t :  Detected gap > 15min in attitude file:    97091509.743114
ASCALIN_V0.9t : Detected gap > 15min in attitude file:
-> Checking if ad33012010s100302m.unf is covered by attitude file
-> Running ascalin on ad33012010s100302m.unf
-> sisph2pi_110397.fits already present in current directory
-> s1_teldef_ascalin.fits already present in current directory
-> Standard Output From FTOOL ascalin:
ASCALIN_V0.9t
 
-> Standard Error Output From FTOOL ascalin
ASCALIN_V0.9t :  Detected gap > 15min in attitude file:    97091509.743114
ASCALIN_V0.9t : Detected gap > 15min in attitude file:
-> Checking if ad33012010s100312m.unf is covered by attitude file
-> Running ascalin on ad33012010s100312m.unf
-> sisph2pi_110397.fits already present in current directory
-> s1_teldef_ascalin.fits already present in current directory
-> Standard Output From FTOOL ascalin:
ASCALIN_V0.9t
 
-> Standard Error Output From FTOOL ascalin
ASCALIN_V0.9t :  Detected gap > 15min in attitude file:    97091509.743114
ASCALIN_V0.9t : Detected gap > 15min in attitude file:

Creating filter files ( 14:07:44 )

-> Fetching rigidity.data.1.23
-> leapsec.fits already present in current directory
-> Making filter file ft960129_1730_2300.mkf
-> Standard Output From FTOOL mkfilter2:
Date and time are: 96/ 1/29 17:30  mjd=50111.729167 
Orbit file name is ./frf.orbit.214
Epoch of Orbital Elements: 1996/1/29 6:59:59
Rigidity Data File: ./rigidity.data.1.23
Attitude FRF: fa960129_1730.2300
S0-HK file: ft960129_1730_2300S0HK.fits
S1-HK file: ft960129_1730_2300S1HK.fits
G2-HK file: ft960129_1730_2300G2HK.fits
G3-HK file: ft960129_1730_2300G3HK.fits
output FITS File: ft960129_1730_2300.mkf
Total 621 Data bins were processed.
-> Checking if column TIME in ft960129_1730_2300.mkf is in order
-> Standard Output From FTOOL cktime:
 
Time column is TIME ORDERED
-> Calculating dead time values for filter file
-> Putting dark frame errors into filter files
-> Plotting quantities from ft960129_1730_2300.mkf

Cleaning and filtering the unfiltered event files ( 14:12:16 )

-> Skipping ad33012010s000101h.unf because of mode
-> Filtering ad33012010s000102h.unf into ad33012010s000102h.evt
-> Standard Output From FTOOL fstatistic:
 The sum of the selected column is                   1968.1308
 The mean of the selected column is                  32.264439
 The standard deviation of the selected column is    21.629922
 The minimum of selected column is                   7.5625219
 The maximum of selected column is                   141.09416
 The number of points used in calculation is               61
-> Using the following selection criteria:
(SAA==0)
&&(BR_EARTH>20)
&&(ELV>10)
&&(COR>6)
&&(ACS==0)
&&(ANG_DIST>0)&& (ANG_DIST<0.01)
&&(FOV==0)
&&
(
(S0_PIXL1>0.0 && S0_PIXL1<97.1 )  )
&&(  (S0_SATF1<1)
   ||(S0_SATF1>1))
&&(  (S0_SATF1<1)
   ||(S0_SATF1>1))
&&(  (S0_SATF1<1)
   ||(S0_SATF1>1))
&&(  (S0_SATF1<1)
   ||(S0_SATF1>1))
&&((T_DY_NT<0)||(T_DY_NT>16))
&&((T_SAA  <0)||(T_SAA  >16))
-> Standard Output From FTOOL xselect:
 
                         **  XSELECT V1.3   **
 
!> Enter session name >[xsel] screen
 
 Notes: XSELECT set up for      ASCA
 Keywords for time and pha are  TIME       PI
 Units of time are              s
 Default timing binsize =    16.00
 Keywords for images are          DETX       DETY
 Keywords for the WMAP are        DETX       DETY
 
 
 
        OBJECT   DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME   NEVENTS  S0CCDPOW
      1 XY_ARI   BRIGHT   HIGH     29/01/96 17:42:55 0.55E+04     3311 0100
 
Processing file: /data/data22/seq_proc/33012010.005/ad33012010s000102h.unf
EXTRACTOR vers 2.0  11 Apr 1997.
 Doing file: /data/data22/seq_proc/33012010.005/screen_work1001.xsl
          Total      Good    Bad: Region      Time     Phase       Cut
           2769      1861              0       908         0         0
 Writing events file
   1861 events written to the output file
===============================================================================
   Grand Total      Good   Bad:  Region      Time     Phase       Cut
          2769      1861              0       908         0         0
   in    3895.92 seconds
CLEANSIS_V1.6
    allocating image arrays...
 
 PROGRAM TO MAKE AN SIS SCIENCE FILE CLEANED OF ANOMALOUS PIXELS.
 
 * Anomalous pixels may consist of at least two populations.
 
 1. Persistent HOT pixels are removed by comparing to the chip mean.
 
 2. Flickering WARM pixels are removed by comparing to the cell mean.
 
 3. In faint areas (zero bgd), flickering pixels are removed with a
    cutoff threshold.
 
 Hints:
 Choose cell size and thresholds based on the expected background and the PSF.
 Use the DIRTYSIS option to examine the anomalous pixel spectra.
 Try a multiple pass clean:
     Choose a PHA cut to optimize the S/N of the flickering pixels,
     then a broad band clean.
 Be suspicious of extended source cleans.
 For very bright sources you may need to turn off the iteration option.
 
 See the help page for further info (fhelp cleansis)
 
 Poisson clean cell size         :            5
 Poisson probability threshold   :    0.631E-05
 Zero Bgd Cutoff threshold (>)   :            3
 Iterate                         :            T
 Dirtysis                        :            F
 
 Minimum PHA value (inclusive)   :            0
 Maximum PHA value (inclusive)   :         4095
 
    open output  file: /data/data22/seq_proc/33012010.005/screen_in_event.xsl
    reading data file: /data/data22/seq_proc/33012010.005/screen_out_event.xsl
    copying primary header to output file...
    making chip image...
 
 File NEVENTS keyword value  :         1861
 Total counts in chip images :         1860
 
    copy bad pix array...
cleaning chip #           0
cleaning chip #           1
 Hot pixels & counts                   :               3        1192
 Flickering pixels iter, pixels & cnts :   1           2           8
cleaning chip #           2
cleaning chip #           3
 
 Number of pixels rejected           :            5
 Number of (internal) image counts   :         1860
 Number of image cts rejected (N, %) :         1200     64.5161285
 
         By chip   :             0            1            2            3
 
 Pixels rejected   :             0            5            0            0
 
 Image counts      :             0         1860            0            0
 Image cts rejected:             0         1200            0            0
 Image cts rej (%) :          0.00        64.52         0.00         0.00
 
    filtering data...
 
 Total counts      :             0         1861            0            0
 Total cts rejected:             0         1200            0            0
 Total cts rej (%) :          0.00        64.48         0.00         0.00
 
 Number of clean counts accepted  :          661
 
    writing history cards...
    copying extensions...
    writing out hot pixs...
 
 Number of rejected pixels        :            5
 
    updating NEVENTS keywords...
    closing data file...
    closing clean file...
 Command not found; type ? for a command listing
!screen:ASCA > set mission ASCA
 
 Notes: XSELECT set up for      ASCA
 Keywords for time and pha are  TIME       PI
 Units of time are              s
 Default timing binsize =    16.00
 Keywords for images are          DETX       DETY
 Keywords for the WMAP are        DETX       DETY
 
!screen:ASCA > set datadir .
 
Setting data directory to /data/data22/seq_proc/33012010.005/
Setting mkf directory to /data/data22/seq_proc/33012010.005/
 
!screen:ASCA > read events ad33012010s000102h.unf
Got new instrument: SIS0
 
Setting: IMAGE binning    =    4
         WMAP binning     =    8
         Energy Column    =  PI
         Energy rebinning =    1
 
 
Getting Min and Max for Energy Column...
Got min and max for PI:     0   2047
 
Got the minimum time resolution of the read data:   4.0000
 Number of files read in:   1
 
******************** Observation Catalogue ********************
 
Data Directory is: /data/data22/seq_proc/33012010.005/
HK Directory is: /data/data22/seq_proc/33012010.005/
 
!screen:ASCA-SIS0-BRIGHT > select event "grade==0||grade==2||grade==3||grade==4"  save_file=no
!screen:ASCA-SIS0-BRIGHT > select mkf "@criteria.tmp" data_dir=. ASCA_mkf_def_expr=ft*.mkf
!screen:ASCA-SIS0-BRIGHT > extract events
!screen:ASCA-SIS0-BRIGHT > sisclean saoimage=no sis_plot=no clean=2 cellsize=5 log_prob=-5.24 bkg_thr=3 clean_phalow=0 clean_phahi=4095
!screen:ASCA-SIS0-BRIGHT > save clean outfile=ad33012010s000102h.evt use_events=no
 Wrote cleaned events file to ad33012010s000102h.evt                                                                                                                                                                                                            
 
!screen:ASCA-SIS0-BRIGHT > exit save_session=no
-> Filtering ad33012010s000112h.unf into ad33012010s000112h.evt
-> Standard Output From FTOOL fstatistic:
 The sum of the selected column is                   1968.1308
 The mean of the selected column is                  32.264439
 The standard deviation of the selected column is    21.629922
 The minimum of selected column is                   7.5625219
 The maximum of selected column is                   141.09416
 The number of points used in calculation is               61
-> Using the following selection criteria:
(SAA==0)
&&(BR_EARTH>20)
&&(ELV>10)
&&(COR>6)
&&(ACS==0)
&&(ANG_DIST>0)&& (ANG_DIST<0.01)
&&(FOV==0)
&&
(
(S0_PIXL1>0.0 && S0_PIXL1<97.1 )  )
&&(  (S0_SATF1<1)
   ||(S0_SATF1>1))
&&(  (S0_SATF1<1)
   ||(S0_SATF1>1))
&&(  (S0_SATF1<1)
   ||(S0_SATF1>1))
&&(  (S0_SATF1<1)
   ||(S0_SATF1>1))
&&((T_DY_NT<0)||(T_DY_NT>16))
&&((T_SAA  <0)||(T_SAA  >16))
-> Standard Output From FTOOL xselect:
 
                         **  XSELECT V1.3   **
 
!> Enter session name >[xsel] screen
 
 Notes: XSELECT set up for      ASCA
 Keywords for time and pha are  TIME       PI
 Units of time are              s
 Default timing binsize =    16.00
 Keywords for images are          DETX       DETY
 Keywords for the WMAP are        DETX       DETY
 
 
 
        OBJECT   DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME   NEVENTS  S0CCDPOW
      1 XY_ARI   BRIGHT2  HIGH     29/01/96 17:42:55 0.55E+04     3460 0100
 
Processing file: /data/data22/seq_proc/33012010.005/ad33012010s000112h.unf
EXTRACTOR vers 2.0  11 Apr 1997.
 Doing file: /data/data22/seq_proc/33012010.005/screen_work1001.xsl
          Total      Good    Bad: Region      Time     Phase       Cut
           2838      1901              0       937         0         0
 Writing events file
   1901 events written to the output file
===============================================================================
   Grand Total      Good   Bad:  Region      Time     Phase       Cut
          2838      1901              0       937         0         0
   in    3895.92 seconds
CLEANSIS_V1.6
    allocating image arrays...
 
 PROGRAM TO MAKE AN SIS SCIENCE FILE CLEANED OF ANOMALOUS PIXELS.
 
 * Anomalous pixels may consist of at least two populations.
 
 1. Persistent HOT pixels are removed by comparing to the chip mean.
 
 2. Flickering WARM pixels are removed by comparing to the cell mean.
 
 3. In faint areas (zero bgd), flickering pixels are removed with a
    cutoff threshold.
 
 Hints:
 Choose cell size and thresholds based on the expected background and the PSF.
 Use the DIRTYSIS option to examine the anomalous pixel spectra.
 Try a multiple pass clean:
     Choose a PHA cut to optimize the S/N of the flickering pixels,
     then a broad band clean.
 Be suspicious of extended source cleans.
 For very bright sources you may need to turn off the iteration option.
 
 See the help page for further info (fhelp cleansis)
 
 Poisson clean cell size         :            5
 Poisson probability threshold   :    0.631E-05
 Zero Bgd Cutoff threshold (>)   :            3
 Iterate                         :            T
 Dirtysis                        :            F
 
 Minimum PHA value (inclusive)   :            0
 Maximum PHA value (inclusive)   :         4095
 
    open output  file: /data/data22/seq_proc/33012010.005/screen_in_event.xsl
    reading data file: /data/data22/seq_proc/33012010.005/screen_out_event.xsl
    copying primary header to output file...
    making chip image...
 
 File NEVENTS keyword value  :         1901
 Total counts in chip images :         1900
 
    copy bad pix array...
cleaning chip #           0
cleaning chip #           1
 Hot pixels & counts                   :               3        1192
 Flickering pixels iter, pixels & cnts :   1           2           8
cleaning chip #           2
cleaning chip #           3
 
 Number of pixels rejected           :            5
 Number of (internal) image counts   :         1900
 Number of image cts rejected (N, %) :         1200     63.1578941
 
         By chip   :             0            1            2            3
 
 Pixels rejected   :             0            5            0            0
 
 Image counts      :             0         1900            0            0
 Image cts rejected:             0         1200            0            0
 Image cts rej (%) :          0.00        63.16         0.00         0.00
 
    filtering data...
 
 Total counts      :             0         1901            0            0
 Total cts rejected:             0         1200            0            0
 Total cts rej (%) :          0.00        63.12         0.00         0.00
 
 Number of clean counts accepted  :          701
 
    writing history cards...
    copying extensions...
    writing out hot pixs...
 
 Number of rejected pixels        :            5
 
    updating NEVENTS keywords...
    closing data file...
    closing clean file...
 Command not found; type ? for a command listing
!screen:ASCA > set mission ASCA
 
 Notes: XSELECT set up for      ASCA
 Keywords for time and pha are  TIME       PI
 Units of time are              s
 Default timing binsize =    16.00
 Keywords for images are          DETX       DETY
 Keywords for the WMAP are        DETX       DETY
 
!screen:ASCA > set datadir .
 
Setting data directory to /data/data22/seq_proc/33012010.005/
Setting mkf directory to /data/data22/seq_proc/33012010.005/
 
!screen:ASCA > read events ad33012010s000112h.unf
Got new instrument: SIS0
 
Setting: IMAGE binning    =    4
         WMAP binning     =    8
         Energy Column    =  PI
         Energy rebinning =    1
 
 
Getting Min and Max for Energy Column...
Got min and max for PI:     0   4095
 
Got the minimum time resolution of the read data:   4.0000
 Number of files read in:   1
 
******************** Observation Catalogue ********************
 
Data Directory is: /data/data22/seq_proc/33012010.005/
HK Directory is: /data/data22/seq_proc/33012010.005/
 
!screen:ASCA-SIS0-BRIGHT2 > select event "grade==0||grade==2||grade==3||grade==4"  save_file=no
!screen:ASCA-SIS0-BRIGHT2 > select mkf "@criteria.tmp" data_dir=. ASCA_mkf_def_expr=ft*.mkf
!screen:ASCA-SIS0-BRIGHT2 > extract events
!screen:ASCA-SIS0-BRIGHT2 > sisclean saoimage=no sis_plot=no clean=2 cellsize=5 log_prob=-5.24 bkg_thr=3 clean_phalow=0 clean_phahi=4095
!screen:ASCA-SIS0-BRIGHT2 > save clean outfile=ad33012010s000112h.evt use_events=no
 Wrote cleaned events file to ad33012010s000112h.evt                                                                                                                                                                                                            
 
!screen:ASCA-SIS0-BRIGHT2 > exit save_session=no
-> Skipping ad33012010s000201l.unf because of mode
-> Filtering ad33012010s000202l.unf into ad33012010s000202l.evt
-> Using the following selection criteria:
(SAA==0)
&&(BR_EARTH>20)
&&(ELV>10)
&&(COR>6)
&&(ACS==0)
&&(ANG_DIST>0)&& (ANG_DIST<0.01)
&&(FOV==0)
&&
(
(S0_PIXL1>0)  )
&&(  (S0_SATF1<1)
   ||(S0_SATF1>1))
&&(  (S0_SATF1<1)
   ||(S0_SATF1>1))
&&(  (S0_SATF1<1)
   ||(S0_SATF1>1))
&&(  (S0_SATF1<1)
   ||(S0_SATF1>1))
&&((T_DY_NT<0)||(T_DY_NT>16))
&&((T_SAA  <0)||(T_SAA  >16))
-> Standard Output From FTOOL xselect:
 
                         **  XSELECT V1.3   **
 
!> Enter session name >[xsel] screen
 
 Notes: XSELECT set up for      ASCA
 Keywords for time and pha are  TIME       PI
 Units of time are              s
 Default timing binsize =    16.00
 Keywords for images are          DETX       DETY
 Keywords for the WMAP are        DETX       DETY
 
 
 
        OBJECT   DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME   NEVENTS  S0CCDPOW
      1 XY_ARI   BRIGHT   LOW      29/01/96 18:44:15 0.77E+04     2473 0100
 
Processing file: /data/data22/seq_proc/33012010.005/ad33012010s000202l.unf
EXTRACTOR vers 2.0  11 Apr 1997.
 Skipping file: /data/data22/seq_proc/33012010.005/screen_work1001.xsl
 Writing events file
      0 events written to the output file
===============================================================================
   Grand Total      Good   Bad:  Region      Time     Phase       Cut
             0         0              0         0         0         0
   in       0.00 seconds
CLEANSIS_V1.6
    allocating image arrays...
 
 PROGRAM TO MAKE AN SIS SCIENCE FILE CLEANED OF ANOMALOUS PIXELS.
 
 * Anomalous pixels may consist of at least two populations.
 
 1. Persistent HOT pixels are removed by comparing to the chip mean.
 
 2. Flickering WARM pixels are removed by comparing to the cell mean.
 
 3. In faint areas (zero bgd), flickering pixels are removed with a
    cutoff threshold.
 
 Hints:
 Choose cell size and thresholds based on the expected background and the PSF.
 Use the DIRTYSIS option to examine the anomalous pixel spectra.
 Try a multiple pass clean:
     Choose a PHA cut to optimize the S/N of the flickering pixels,
     then a broad band clean.
 Be suspicious of extended source cleans.
 For very bright sources you may need to turn off the iteration option.
 
 See the help page for further info (fhelp cleansis)
 
 Poisson clean cell size         :            5
 Poisson probability threshold   :    0.631E-05
 Zero Bgd Cutoff threshold (>)   :            3
 Iterate                         :            T
 Dirtysis                        :            F
 
 Minimum PHA value (inclusive)   :            0
 Maximum PHA value (inclusive)   :         4095
 
    open output  file: /data/data22/seq_proc/33012010.005/screen_in_event.xsl
    reading data file: /data/data22/seq_proc/33012010.005/screen_out_event.xsl
    copying primary header to output file...
    making chip image...
 
 Total counts in chip images :            0
 
    copy bad pix array...
cleaning chip #           0
cleaning chip #           1
cleaning chip #           2
cleaning chip #           3
 
 Number of pixels rejected           :            0
 Number of (internal) image counts   :            0
 Number of image cts rejected (N, %) :            0      0.0000000
 
         By chip   :             0            1            2            3
 
 Pixels rejected   :             0            0            0            0
 
 Image counts      :             0            0            0            0
 Image cts rejected:             0            0            0            0
 Image cts rej (%) :          0.00         0.00         0.00         0.00
 
    filtering data...
 
 Total counts      :             0            0            0            0
 Total cts rejected:             0            0            0            0
 Total cts rej (%) :          0.00         0.00         0.00         0.00
 
 Number of clean counts accepted  :            0
 
    writing history cards...
    copying extensions...
    writing out hot pixs...
 
 Number of rejected pixels        :            0
 
    updating NEVENTS keywords...
    closing data file...
    closing clean file...
 Command not found; type ? for a command listing
!screen:ASCA > set mission ASCA
 
 Notes: XSELECT set up for      ASCA
 Keywords for time and pha are  TIME       PI
 Units of time are              s
 Default timing binsize =    16.00
 Keywords for images are          DETX       DETY
 Keywords for the WMAP are        DETX       DETY
 
!screen:ASCA > set datadir .
 
Setting data directory to /data/data22/seq_proc/33012010.005/
Setting mkf directory to /data/data22/seq_proc/33012010.005/
 
!screen:ASCA > read events ad33012010s000202l.unf
Got new instrument: SIS0
 
Setting: IMAGE binning    =    4
         WMAP binning     =    8
         Energy Column    =  PI
         Energy rebinning =    1
 
 
Getting Min and Max for Energy Column...
Got min and max for PI:     0   2047
 
Got the minimum time resolution of the read data:   4.0000
 Number of files read in:   1
 
******************** Observation Catalogue ********************
 
Data Directory is: /data/data22/seq_proc/33012010.005/
HK Directory is: /data/data22/seq_proc/33012010.005/
 
!screen:ASCA-SIS0-BRIGHT > select event "grade==0||grade==2||grade==3||grade==4"  save_file=no
!screen:ASCA-SIS0-BRIGHT > select mkf "@criteria.tmp" data_dir=. ASCA_mkf_def_expr=ft*.mkf
!screen:ASCA-SIS0-BRIGHT > extract events
!screen:ASCA-SIS0-BRIGHT > sisclean saoimage=no sis_plot=no clean=2 cellsize=5 log_prob=-5.24 bkg_thr=3 clean_phalow=0 clean_phahi=4095
!screen:ASCA-SIS0-BRIGHT > save clean outfile=ad33012010s000202l.evt use_events=no
 Wrote cleaned events file to ad33012010s000202l.evt                                                                                                                                                                                                            
 
!screen:ASCA-SIS0-BRIGHT > exit save_session=no
-> Deleting ad33012010s000202l.evt since it contains 0 events
-> Filtering ad33012010s000212l.unf into ad33012010s000212l.evt
-> Using the following selection criteria:
(SAA==0)
&&(BR_EARTH>20)
&&(ELV>10)
&&(COR>6)
&&(ACS==0)
&&(ANG_DIST>0)&& (ANG_DIST<0.01)
&&(FOV==0)
&&
(
(S0_PIXL1>0)  )
&&(  (S0_SATF1<1)
   ||(S0_SATF1>1))
&&(  (S0_SATF1<1)
   ||(S0_SATF1>1))
&&(  (S0_SATF1<1)
   ||(S0_SATF1>1))
&&(  (S0_SATF1<1)
   ||(S0_SATF1>1))
&&((T_DY_NT<0)||(T_DY_NT>16))
&&((T_SAA  <0)||(T_SAA  >16))
-> Standard Output From FTOOL xselect:
 
                         **  XSELECT V1.3   **
 
!> Enter session name >[xsel] screen
 
 Notes: XSELECT set up for      ASCA
 Keywords for time and pha are  TIME       PI
 Units of time are              s
 Default timing binsize =    16.00
 Keywords for images are          DETX       DETY
 Keywords for the WMAP are        DETX       DETY
 
 
 
        OBJECT   DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME   NEVENTS  S0CCDPOW
      1 XY_ARI   BRIGHT2  LOW      29/01/96 18:44:15 0.77E+04     2538 0100
 
Processing file: /data/data22/seq_proc/33012010.005/ad33012010s000212l.unf
EXTRACTOR vers 2.0  11 Apr 1997.
 Skipping file: /data/data22/seq_proc/33012010.005/screen_work1001.xsl
 Writing events file
      0 events written to the output file
===============================================================================
   Grand Total      Good   Bad:  Region      Time     Phase       Cut
             0         0              0         0         0         0
   in       0.00 seconds
CLEANSIS_V1.6
    allocating image arrays...
 
 PROGRAM TO MAKE AN SIS SCIENCE FILE CLEANED OF ANOMALOUS PIXELS.
 
 * Anomalous pixels may consist of at least two populations.
 
 1. Persistent HOT pixels are removed by comparing to the chip mean.
 
 2. Flickering WARM pixels are removed by comparing to the cell mean.
 
 3. In faint areas (zero bgd), flickering pixels are removed with a
    cutoff threshold.
 
 Hints:
 Choose cell size and thresholds based on the expected background and the PSF.
 Use the DIRTYSIS option to examine the anomalous pixel spectra.
 Try a multiple pass clean:
     Choose a PHA cut to optimize the S/N of the flickering pixels,
     then a broad band clean.
 Be suspicious of extended source cleans.
 For very bright sources you may need to turn off the iteration option.
 
 See the help page for further info (fhelp cleansis)
 
 Poisson clean cell size         :            5
 Poisson probability threshold   :    0.631E-05
 Zero Bgd Cutoff threshold (>)   :            3
 Iterate                         :            T
 Dirtysis                        :            F
 
 Minimum PHA value (inclusive)   :            0
 Maximum PHA value (inclusive)   :         4095
 
    open output  file: /data/data22/seq_proc/33012010.005/screen_in_event.xsl
    reading data file: /data/data22/seq_proc/33012010.005/screen_out_event.xsl
    copying primary header to output file...
    making chip image...
 
 Total counts in chip images :            0
 
    copy bad pix array...
cleaning chip #           0
cleaning chip #           1
cleaning chip #           2
cleaning chip #           3
 
 Number of pixels rejected           :            0
 Number of (internal) image counts   :            0
 Number of image cts rejected (N, %) :            0      0.0000000
 
         By chip   :             0            1            2            3
 
 Pixels rejected   :             0            0            0            0
 
 Image counts      :             0            0            0            0
 Image cts rejected:             0            0            0            0
 Image cts rej (%) :          0.00         0.00         0.00         0.00
 
    filtering data...
 
 Total counts      :             0            0            0            0
 Total cts rejected:             0            0            0            0
 Total cts rej (%) :          0.00         0.00         0.00         0.00
 
 Number of clean counts accepted  :            0
 
    writing history cards...
    copying extensions...
    writing out hot pixs...
 
 Number of rejected pixels        :            0
 
    updating NEVENTS keywords...
    closing data file...
    closing clean file...
 Command not found; type ? for a command listing
!screen:ASCA > set mission ASCA
 
 Notes: XSELECT set up for      ASCA
 Keywords for time and pha are  TIME       PI
 Units of time are              s
 Default timing binsize =    16.00
 Keywords for images are          DETX       DETY
 Keywords for the WMAP are        DETX       DETY
 
!screen:ASCA > set datadir .
 
Setting data directory to /data/data22/seq_proc/33012010.005/
Setting mkf directory to /data/data22/seq_proc/33012010.005/
 
!screen:ASCA > read events ad33012010s000212l.unf
Got new instrument: SIS0
 
Setting: IMAGE binning    =    4
         WMAP binning     =    8
         Energy Column    =  PI
         Energy rebinning =    1
 
 
Getting Min and Max for Energy Column...
Got min and max for PI:     0   4095
 
Got the minimum time resolution of the read data:   4.0000
 Number of files read in:   1
 
******************** Observation Catalogue ********************
 
Data Directory is: /data/data22/seq_proc/33012010.005/
HK Directory is: /data/data22/seq_proc/33012010.005/
 
!screen:ASCA-SIS0-BRIGHT2 > select event "grade==0||grade==2||grade==3||grade==4"  save_file=no
!screen:ASCA-SIS0-BRIGHT2 > select mkf "@criteria.tmp" data_dir=. ASCA_mkf_def_expr=ft*.mkf
!screen:ASCA-SIS0-BRIGHT2 > extract events
!screen:ASCA-SIS0-BRIGHT2 > sisclean saoimage=no sis_plot=no clean=2 cellsize=5 log_prob=-5.24 bkg_thr=3 clean_phalow=0 clean_phahi=4095
!screen:ASCA-SIS0-BRIGHT2 > save clean outfile=ad33012010s000212l.evt use_events=no
 Wrote cleaned events file to ad33012010s000212l.evt                                                                                                                                                                                                            
 
!screen:ASCA-SIS0-BRIGHT2 > exit save_session=no
-> Deleting ad33012010s000212l.evt since it contains 0 events
-> Skipping ad33012010s000301m.unf because of mode
-> Filtering ad33012010s000302m.unf into ad33012010s000302m.evt
-> Standard Output From FTOOL fstatistic:
 The sum of the selected column is                   251.03200
 The mean of the selected column is                  27.892444
 The standard deviation of the selected column is    5.8689909
 The minimum of selected column is                   17.750053
 The maximum of selected column is                   37.125111
 The number of points used in calculation is                9
-> Using the following selection criteria:
(SAA==0)
&&(BR_EARTH>20)
&&(ELV>10)
&&(COR>6)
&&(ACS==0)
&&(ANG_DIST>0)&& (ANG_DIST<0.01)
&&(FOV==0)
&&
(
(S0_PIXL1>10.2 && S0_PIXL1<45.4 )  )
&&(  (S0_SATF1<1)
   ||(S0_SATF1>1))
&&(  (S0_SATF1<1)
   ||(S0_SATF1>1))
&&(  (S0_SATF1<1)
   ||(S0_SATF1>1))
&&(  (S0_SATF1<1)
   ||(S0_SATF1>1))
&&((T_DY_NT<0)||(T_DY_NT>16))
&&((T_SAA  <0)||(T_SAA  >16))
-> Standard Output From FTOOL xselect:
 
                         **  XSELECT V1.3   **
 
!> Enter session name >[xsel] screen
 
 Notes: XSELECT set up for      ASCA
 Keywords for time and pha are  TIME       PI
 Units of time are              s
 Default timing binsize =    16.00
 Keywords for images are          DETX       DETY
 Keywords for the WMAP are        DETX       DETY
 
 
 
        OBJECT   DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME   NEVENTS  S0CCDPOW
      1 XY_ARI   BRIGHT   MEDIUM   29/01/96 17:30:23 0.32E+04     2135 0100
 
Processing file: /data/data22/seq_proc/33012010.005/ad33012010s000302m.unf
EXTRACTOR vers 2.0  11 Apr 1997.
 Doing file: /data/data22/seq_proc/33012010.005/screen_work1001.xsl
          Total      Good    Bad: Region      Time     Phase       Cut
           1713       349              0      1364         0         0
 Writing events file
    349 events written to the output file
===============================================================================
   Grand Total      Good   Bad:  Region      Time     Phase       Cut
          1713       349              0      1364         0         0
   in     695.73 seconds
CLEANSIS_V1.6
    allocating image arrays...
 
 PROGRAM TO MAKE AN SIS SCIENCE FILE CLEANED OF ANOMALOUS PIXELS.
 
 * Anomalous pixels may consist of at least two populations.
 
 1. Persistent HOT pixels are removed by comparing to the chip mean.
 
 2. Flickering WARM pixels are removed by comparing to the cell mean.
 
 3. In faint areas (zero bgd), flickering pixels are removed with a
    cutoff threshold.
 
 Hints:
 Choose cell size and thresholds based on the expected background and the PSF.
 Use the DIRTYSIS option to examine the anomalous pixel spectra.
 Try a multiple pass clean:
     Choose a PHA cut to optimize the S/N of the flickering pixels,
     then a broad band clean.
 Be suspicious of extended source cleans.
 For very bright sources you may need to turn off the iteration option.
 
 See the help page for further info (fhelp cleansis)
 
 Poisson clean cell size         :            5
 Poisson probability threshold   :    0.631E-05
 Zero Bgd Cutoff threshold (>)   :            3
 Iterate                         :            T
 Dirtysis                        :            F
 
 Minimum PHA value (inclusive)   :            0
 Maximum PHA value (inclusive)   :         4095
 
    open output  file: /data/data22/seq_proc/33012010.005/screen_in_event.xsl
    reading data file: /data/data22/seq_proc/33012010.005/screen_out_event.xsl
    copying primary header to output file...
    making chip image...
 
 Total counts in chip images :          349
 
    copy bad pix array...
cleaning chip #           0
cleaning chip #           1
 Hot pixels & counts                   :               2         198
cleaning chip #           2
cleaning chip #           3
 
 Number of pixels rejected           :            2
 Number of (internal) image counts   :          349
 Number of image cts rejected (N, %) :          198     56.7335243
 
         By chip   :             0            1            2            3
 
 Pixels rejected   :             0            2            0            0
 
 Image counts      :             0          349            0            0
 Image cts rejected:             0          198            0            0
 Image cts rej (%) :          0.00        56.73         0.00         0.00
 
    filtering data...
 
 Total counts      :             0          349            0            0
 Total cts rejected:             0          198            0            0
 Total cts rej (%) :          0.00        56.73         0.00         0.00
 
 Number of clean counts accepted  :          151
 
    writing history cards...
    copying extensions...
    writing out hot pixs...
 
 Number of rejected pixels        :            2
 
    updating NEVENTS keywords...
    closing data file...
    closing clean file...
 Command not found; type ? for a command listing
!screen:ASCA > set mission ASCA
 
 Notes: XSELECT set up for      ASCA
 Keywords for time and pha are  TIME       PI
 Units of time are              s
 Default timing binsize =    16.00
 Keywords for images are          DETX       DETY
 Keywords for the WMAP are        DETX       DETY
 
!screen:ASCA > set datadir .
 
Setting data directory to /data/data22/seq_proc/33012010.005/
Setting mkf directory to /data/data22/seq_proc/33012010.005/
 
!screen:ASCA > read events ad33012010s000302m.unf
Got new instrument: SIS0
 
Setting: IMAGE binning    =    4
         WMAP binning     =    8
         Energy Column    =  PI
         Energy rebinning =    1
 
 
Getting Min and Max for Energy Column...
Got min and max for PI:     0   2047
 
Got the minimum time resolution of the read data:   4.0000
 Number of files read in:   1
 
******************** Observation Catalogue ********************
 
Data Directory is: /data/data22/seq_proc/33012010.005/
HK Directory is: /data/data22/seq_proc/33012010.005/
 
!screen:ASCA-SIS0-BRIGHT > select event "grade==0||grade==2||grade==3||grade==4"  save_file=no
!screen:ASCA-SIS0-BRIGHT > select mkf "@criteria.tmp" data_dir=. ASCA_mkf_def_expr=ft*.mkf
!screen:ASCA-SIS0-BRIGHT > extract events
!screen:ASCA-SIS0-BRIGHT > sisclean saoimage=no sis_plot=no clean=2 cellsize=5 log_prob=-5.24 bkg_thr=3 clean_phalow=0 clean_phahi=4095
!screen:ASCA-SIS0-BRIGHT > save clean outfile=ad33012010s000302m.evt use_events=no
 Wrote cleaned events file to ad33012010s000302m.evt                                                                                                                                                                                                            
 
!screen:ASCA-SIS0-BRIGHT > exit save_session=no
-> Filtering ad33012010s000312m.unf into ad33012010s000312m.evt
-> Standard Output From FTOOL fstatistic:
 The sum of the selected column is                   251.03200
 The mean of the selected column is                  27.892444
 The standard deviation of the selected column is    5.8689909
 The minimum of selected column is                   17.750053
 The maximum of selected column is                   37.125111
 The number of points used in calculation is                9
-> Using the following selection criteria:
(SAA==0)
&&(BR_EARTH>20)
&&(ELV>10)
&&(COR>6)
&&(ACS==0)
&&(ANG_DIST>0)&& (ANG_DIST<0.01)
&&(FOV==0)
&&
(
(S0_PIXL1>10.2 && S0_PIXL1<45.4 )  )
&&(  (S0_SATF1<1)
   ||(S0_SATF1>1))
&&(  (S0_SATF1<1)
   ||(S0_SATF1>1))
&&(  (S0_SATF1<1)
   ||(S0_SATF1>1))
&&(  (S0_SATF1<1)
   ||(S0_SATF1>1))
&&((T_DY_NT<0)||(T_DY_NT>16))
&&((T_SAA  <0)||(T_SAA  >16))
-> Standard Output From FTOOL xselect:
 
                         **  XSELECT V1.3   **
 
!> Enter session name >[xsel] screen
 
 Notes: XSELECT set up for      ASCA
 Keywords for time and pha are  TIME       PI
 Units of time are              s
 Default timing binsize =    16.00
 Keywords for images are          DETX       DETY
 Keywords for the WMAP are        DETX       DETY
 
 
 
        OBJECT   DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME   NEVENTS  S0CCDPOW
      1 XY_ARI   BRIGHT2  MEDIUM   29/01/96 17:30:23 0.32E+04     2201 0100
 
Processing file: /data/data22/seq_proc/33012010.005/ad33012010s000312m.unf
EXTRACTOR vers 2.0  11 Apr 1997.
 Doing file: /data/data22/seq_proc/33012010.005/screen_work1001.xsl
          Total      Good    Bad: Region      Time     Phase       Cut
           1747       360              0      1387         0         0
 Writing events file
    360 events written to the output file
===============================================================================
   Grand Total      Good   Bad:  Region      Time     Phase       Cut
          1747       360              0      1387         0         0
   in     695.73 seconds
CLEANSIS_V1.6
    allocating image arrays...
 
 PROGRAM TO MAKE AN SIS SCIENCE FILE CLEANED OF ANOMALOUS PIXELS.
 
 * Anomalous pixels may consist of at least two populations.
 
 1. Persistent HOT pixels are removed by comparing to the chip mean.
 
 2. Flickering WARM pixels are removed by comparing to the cell mean.
 
 3. In faint areas (zero bgd), flickering pixels are removed with a
    cutoff threshold.
 
 Hints:
 Choose cell size and thresholds based on the expected background and the PSF.
 Use the DIRTYSIS option to examine the anomalous pixel spectra.
 Try a multiple pass clean:
     Choose a PHA cut to optimize the S/N of the flickering pixels,
     then a broad band clean.
 Be suspicious of extended source cleans.
 For very bright sources you may need to turn off the iteration option.
 
 See the help page for further info (fhelp cleansis)
 
 Poisson clean cell size         :            5
 Poisson probability threshold   :    0.631E-05
 Zero Bgd Cutoff threshold (>)   :            3
 Iterate                         :            T
 Dirtysis                        :            F
 
 Minimum PHA value (inclusive)   :            0
 Maximum PHA value (inclusive)   :         4095
 
    open output  file: /data/data22/seq_proc/33012010.005/screen_in_event.xsl
    reading data file: /data/data22/seq_proc/33012010.005/screen_out_event.xsl
    copying primary header to output file...
    making chip image...
 
 Total counts in chip images :          360
 
    copy bad pix array...
cleaning chip #           0
cleaning chip #           1
 Hot pixels & counts                   :               2         198
cleaning chip #           2
cleaning chip #           3
 
 Number of pixels rejected           :            2
 Number of (internal) image counts   :          360
 Number of image cts rejected (N, %) :          198     55.0000000
 
         By chip   :             0            1            2            3
 
 Pixels rejected   :             0            2            0            0
 
 Image counts      :             0          360            0            0
 Image cts rejected:             0          198            0            0
 Image cts rej (%) :          0.00        55.00         0.00         0.00
 
    filtering data...
 
 Total counts      :             0          360            0            0
 Total cts rejected:             0          198            0            0
 Total cts rej (%) :          0.00        55.00         0.00         0.00
 
 Number of clean counts accepted  :          162
 
    writing history cards...
    copying extensions...
    writing out hot pixs...
 
 Number of rejected pixels        :            2
 
    updating NEVENTS keywords...
    closing data file...
    closing clean file...
 Command not found; type ? for a command listing
!screen:ASCA > set mission ASCA
 
 Notes: XSELECT set up for      ASCA
 Keywords for time and pha are  TIME       PI
 Units of time are              s
 Default timing binsize =    16.00
 Keywords for images are          DETX       DETY
 Keywords for the WMAP are        DETX       DETY
 
!screen:ASCA > set datadir .
 
Setting data directory to /data/data22/seq_proc/33012010.005/
Setting mkf directory to /data/data22/seq_proc/33012010.005/
 
!screen:ASCA > read events ad33012010s000312m.unf
Got new instrument: SIS0
 
Setting: IMAGE binning    =    4
         WMAP binning     =    8
         Energy Column    =  PI
         Energy rebinning =    1
 
 
Getting Min and Max for Energy Column...
Got min and max for PI:     0   4095
 
Got the minimum time resolution of the read data:   4.0000
 Number of files read in:   1
 
******************** Observation Catalogue ********************
 
Data Directory is: /data/data22/seq_proc/33012010.005/
HK Directory is: /data/data22/seq_proc/33012010.005/
 
!screen:ASCA-SIS0-BRIGHT2 > select event "grade==0||grade==2||grade==3||grade==4"  save_file=no
!screen:ASCA-SIS0-BRIGHT2 > select mkf "@criteria.tmp" data_dir=. ASCA_mkf_def_expr=ft*.mkf
!screen:ASCA-SIS0-BRIGHT2 > extract events
!screen:ASCA-SIS0-BRIGHT2 > sisclean saoimage=no sis_plot=no clean=2 cellsize=5 log_prob=-5.24 bkg_thr=3 clean_phalow=0 clean_phahi=4095
!screen:ASCA-SIS0-BRIGHT2 > save clean outfile=ad33012010s000312m.evt use_events=no
 Wrote cleaned events file to ad33012010s000312m.evt                                                                                                                                                                                                            
 
!screen:ASCA-SIS0-BRIGHT2 > exit save_session=no
-> Skipping ad33012010s100101h.unf because of mode
-> Filtering ad33012010s100102h.unf into ad33012010s100102h.evt
-> Standard Output From FTOOL fstatistic:
 The sum of the selected column is                   2816.0708
 The mean of the selected column is                  46.165095
 The standard deviation of the selected column is    28.315016
 The minimum of selected column is                   7.8125229
 The maximum of selected column is                   209.56311
 The number of points used in calculation is               61
-> Using the following selection criteria:
(SAA==0)
&&(BR_EARTH>20)
&&(ELV>10)
&&(COR>6)
&&(ACS==0)
&&(ANG_DIST>0)&& (ANG_DIST<0.01)
&&(FOV==0)
&&
(
(S1_PIXL3>0.0 && S1_PIXL3<131.1 )  )
&&(  (S1_SATF3<1)
   ||(S1_SATF3>1))
&&(  (S1_SATF3<1)
   ||(S1_SATF3>1))
&&(  (S1_SATF3<1)
   ||(S1_SATF3>1))
&&(  (S1_SATF3<1)
   ||(S1_SATF3>1))
&&((T_DY_NT<0)||(T_DY_NT>16))
&&((T_SAA  <0)||(T_SAA  >16))
-> Standard Output From FTOOL xselect:
 
                         **  XSELECT V1.3   **
 
!> Enter session name >[xsel] screen
 
 Notes: XSELECT set up for      ASCA
 Keywords for time and pha are  TIME       PI
 Units of time are              s
 Default timing binsize =    16.00
 Keywords for images are          DETX       DETY
 Keywords for the WMAP are        DETX       DETY
 
 
 
        OBJECT   DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME   NEVENTS  S1CCDPOW
      1 XY_ARI   BRIGHT   HIGH     29/01/96 17:42:55 0.55E+04     8800 0001
 
Processing file: /data/data22/seq_proc/33012010.005/ad33012010s100102h.unf
EXTRACTOR vers 2.0  11 Apr 1997.
 Doing file: /data/data22/seq_proc/33012010.005/screen_work1001.xsl
          Total      Good    Bad: Region      Time     Phase       Cut
           8342      5944              0      2398         0         0
 Writing events file
   5944 events written to the output file
===============================================================================
   Grand Total      Good   Bad:  Region      Time     Phase       Cut
          8342      5944              0      2398         0         0
   in    3937.89 seconds
CLEANSIS_V1.6
    allocating image arrays...
 
 PROGRAM TO MAKE AN SIS SCIENCE FILE CLEANED OF ANOMALOUS PIXELS.
 
 * Anomalous pixels may consist of at least two populations.
 
 1. Persistent HOT pixels are removed by comparing to the chip mean.
 
 2. Flickering WARM pixels are removed by comparing to the cell mean.
 
 3. In faint areas (zero bgd), flickering pixels are removed with a
    cutoff threshold.
 
 Hints:
 Choose cell size and thresholds based on the expected background and the PSF.
 Use the DIRTYSIS option to examine the anomalous pixel spectra.
 Try a multiple pass clean:
     Choose a PHA cut to optimize the S/N of the flickering pixels,
     then a broad band clean.
 Be suspicious of extended source cleans.
 For very bright sources you may need to turn off the iteration option.
 
 See the help page for further info (fhelp cleansis)
 
 Poisson clean cell size         :            5
 Poisson probability threshold   :    0.631E-05
 Zero Bgd Cutoff threshold (>)   :            3
 Iterate                         :            T
 Dirtysis                        :            F
 
 Minimum PHA value (inclusive)   :            0
 Maximum PHA value (inclusive)   :         4095
 
    open output  file: /data/data22/seq_proc/33012010.005/screen_in_event.xsl
    reading data file: /data/data22/seq_proc/33012010.005/screen_out_event.xsl
    copying primary header to output file...
    making chip image...
 
 Total counts in chip images :         5944
 
    copy bad pix array...
cleaning chip #           0
cleaning chip #           1
cleaning chip #           2
cleaning chip #           3
 Hot pixels & counts                   :               8        5308
 Flickering pixels iter, pixels & cnts :   1           2           8
 
 Number of pixels rejected           :           10
 Number of (internal) image counts   :         5944
 Number of image cts rejected (N, %) :         5316     89.4347229
 
         By chip   :             0            1            2            3
 
 Pixels rejected   :             0            0            0           10
 
 Image counts      :             0            0            0         5944
 Image cts rejected:             0            0            0         5316
 Image cts rej (%) :          0.00         0.00         0.00        89.43
 
    filtering data...
 
 Total counts      :             0            0            0         5944
 Total cts rejected:             0            0            0         5316
 Total cts rej (%) :          0.00         0.00         0.00        89.43
 
 Number of clean counts accepted  :          628
 
    writing history cards...
    copying extensions...
    writing out hot pixs...
 
 Number of rejected pixels        :           10
 
    updating NEVENTS keywords...
    closing data file...
    closing clean file...
 Command not found; type ? for a command listing
!screen:ASCA > set mission ASCA
 
 Notes: XSELECT set up for      ASCA
 Keywords for time and pha are  TIME       PI
 Units of time are              s
 Default timing binsize =    16.00
 Keywords for images are          DETX       DETY
 Keywords for the WMAP are        DETX       DETY
 
!screen:ASCA > set datadir .
 
Setting data directory to /data/data22/seq_proc/33012010.005/
Setting mkf directory to /data/data22/seq_proc/33012010.005/
 
!screen:ASCA > read events ad33012010s100102h.unf
Got new instrument: SIS1
 
Setting: IMAGE binning    =    4
         WMAP binning     =    8
         Energy Column    =  PI
         Energy rebinning =    1
 
 
Getting Min and Max for Energy Column...
Got min and max for PI:     0   2047
 
Got the minimum time resolution of the read data:   4.0000
 Number of files read in:   1
 
******************** Observation Catalogue ********************
 
Data Directory is: /data/data22/seq_proc/33012010.005/
HK Directory is: /data/data22/seq_proc/33012010.005/
 
!screen:ASCA-SIS1-BRIGHT > select event "grade==0||grade==2||grade==3||grade==4"  save_file=no
!screen:ASCA-SIS1-BRIGHT > select mkf "@criteria.tmp" data_dir=. ASCA_mkf_def_expr=ft*.mkf
!screen:ASCA-SIS1-BRIGHT > extract events
!screen:ASCA-SIS1-BRIGHT > sisclean saoimage=no sis_plot=no clean=2 cellsize=5 log_prob=-5.24 bkg_thr=3 clean_phalow=0 clean_phahi=4095
!screen:ASCA-SIS1-BRIGHT > save clean outfile=ad33012010s100102h.evt use_events=no
 Wrote cleaned events file to ad33012010s100102h.evt                                                                                                                                                                                                            
 
!screen:ASCA-SIS1-BRIGHT > exit save_session=no
-> Filtering ad33012010s100112h.unf into ad33012010s100112h.evt
-> Standard Output From FTOOL fstatistic:
 The sum of the selected column is                   2816.0708
 The mean of the selected column is                  46.165095
 The standard deviation of the selected column is    28.315016
 The minimum of selected column is                   7.8125229
 The maximum of selected column is                   209.56311
 The number of points used in calculation is               61
-> Using the following selection criteria:
(SAA==0)
&&(BR_EARTH>20)
&&(ELV>10)
&&(COR>6)
&&(ACS==0)
&&(ANG_DIST>0)&& (ANG_DIST<0.01)
&&(FOV==0)
&&
(
(S1_PIXL3>0.0 && S1_PIXL3<131.1 )  )
&&(  (S1_SATF3<1)
   ||(S1_SATF3>1))
&&(  (S1_SATF3<1)
   ||(S1_SATF3>1))
&&(  (S1_SATF3<1)
   ||(S1_SATF3>1))
&&(  (S1_SATF3<1)
   ||(S1_SATF3>1))
&&((T_DY_NT<0)||(T_DY_NT>16))
&&((T_SAA  <0)||(T_SAA  >16))
-> Standard Output From FTOOL xselect:
 
                         **  XSELECT V1.3   **
 
!> Enter session name >[xsel] screen
 
 Notes: XSELECT set up for      ASCA
 Keywords for time and pha are  TIME       PI
 Units of time are              s
 Default timing binsize =    16.00
 Keywords for images are          DETX       DETY
 Keywords for the WMAP are        DETX       DETY
 
 
 
        OBJECT   DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME   NEVENTS  S1CCDPOW
      1 XY_ARI   BRIGHT2  HIGH     29/01/96 17:42:55 0.55E+04     8919 0001
 
Processing file: /data/data22/seq_proc/33012010.005/ad33012010s100112h.unf
EXTRACTOR vers 2.0  11 Apr 1997.
 Doing file: /data/data22/seq_proc/33012010.005/screen_work1001.xsl
          Total      Good    Bad: Region      Time     Phase       Cut
           8385      5964              0      2421         0         0
 Writing events file
   5964 events written to the output file
===============================================================================
   Grand Total      Good   Bad:  Region      Time     Phase       Cut
          8385      5964              0      2421         0         0
   in    3937.89 seconds
CLEANSIS_V1.6
    allocating image arrays...
 
 PROGRAM TO MAKE AN SIS SCIENCE FILE CLEANED OF ANOMALOUS PIXELS.
 
 * Anomalous pixels may consist of at least two populations.
 
 1. Persistent HOT pixels are removed by comparing to the chip mean.
 
 2. Flickering WARM pixels are removed by comparing to the cell mean.
 
 3. In faint areas (zero bgd), flickering pixels are removed with a
    cutoff threshold.
 
 Hints:
 Choose cell size and thresholds based on the expected background and the PSF.
 Use the DIRTYSIS option to examine the anomalous pixel spectra.
 Try a multiple pass clean:
     Choose a PHA cut to optimize the S/N of the flickering pixels,
     then a broad band clean.
 Be suspicious of extended source cleans.
 For very bright sources you may need to turn off the iteration option.
 
 See the help page for further info (fhelp cleansis)
 
 Poisson clean cell size         :            5
 Poisson probability threshold   :    0.631E-05
 Zero Bgd Cutoff threshold (>)   :            3
 Iterate                         :            T
 Dirtysis                        :            F
 
 Minimum PHA value (inclusive)   :            0
 Maximum PHA value (inclusive)   :         4095
 
    open output  file: /data/data22/seq_proc/33012010.005/screen_in_event.xsl
    reading data file: /data/data22/seq_proc/33012010.005/screen_out_event.xsl
    copying primary header to output file...
    making chip image...
 
 Total counts in chip images :         5964
 
    copy bad pix array...
cleaning chip #           0
cleaning chip #           1
cleaning chip #           2
cleaning chip #           3
 Hot pixels & counts                   :               8        5307
 Flickering pixels iter, pixels & cnts :   1           2           8
 
 Number of pixels rejected           :           10
 Number of (internal) image counts   :         5964
 Number of image cts rejected (N, %) :         5315     89.1180420
 
         By chip   :             0            1            2            3
 
 Pixels rejected   :             0            0            0           10
 
 Image counts      :             0            0            0         5964
 Image cts rejected:             0            0            0         5315
 Image cts rej (%) :          0.00         0.00         0.00        89.12
 
    filtering data...
 
 Total counts      :             0            0            0         5964
 Total cts rejected:             0            0            0         5315
 Total cts rej (%) :          0.00         0.00         0.00        89.12
 
 Number of clean counts accepted  :          649
 
    writing history cards...
    copying extensions...
    writing out hot pixs...
 
 Number of rejected pixels        :           10
 
    updating NEVENTS keywords...
    closing data file...
    closing clean file...
 Command not found; type ? for a command listing
!screen:ASCA > set mission ASCA
 
 Notes: XSELECT set up for      ASCA
 Keywords for time and pha are  TIME       PI
 Units of time are              s
 Default timing binsize =    16.00
 Keywords for images are          DETX       DETY
 Keywords for the WMAP are        DETX       DETY
 
!screen:ASCA > set datadir .
 
Setting data directory to /data/data22/seq_proc/33012010.005/
Setting mkf directory to /data/data22/seq_proc/33012010.005/
 
!screen:ASCA > read events ad33012010s100112h.unf
Got new instrument: SIS1
 
Setting: IMAGE binning    =    4
         WMAP binning     =    8
         Energy Column    =  PI
         Energy rebinning =    1
 
 
Getting Min and Max for Energy Column...
Got min and max for PI:     0   4095
 
Got the minimum time resolution of the read data:   4.0000
 Number of files read in:   1
 
******************** Observation Catalogue ********************
 
Data Directory is: /data/data22/seq_proc/33012010.005/
HK Directory is: /data/data22/seq_proc/33012010.005/
 
!screen:ASCA-SIS1-BRIGHT2 > select event "grade==0||grade==2||grade==3||grade==4"  save_file=no
!screen:ASCA-SIS1-BRIGHT2 > select mkf "@criteria.tmp" data_dir=. ASCA_mkf_def_expr=ft*.mkf
!screen:ASCA-SIS1-BRIGHT2 > extract events
!screen:ASCA-SIS1-BRIGHT2 > sisclean saoimage=no sis_plot=no clean=2 cellsize=5 log_prob=-5.24 bkg_thr=3 clean_phalow=0 clean_phahi=4095
!screen:ASCA-SIS1-BRIGHT2 > save clean outfile=ad33012010s100112h.evt use_events=no
 Wrote cleaned events file to ad33012010s100112h.evt                                                                                                                                                                                                            
 
!screen:ASCA-SIS1-BRIGHT2 > exit save_session=no
-> Skipping ad33012010s100201l.unf because of mode
-> Filtering ad33012010s100202l.unf into ad33012010s100202l.evt
-> Using the following selection criteria:
(SAA==0)
&&(BR_EARTH>20)
&&(ELV>10)
&&(COR>6)
&&(ACS==0)
&&(ANG_DIST>0)&& (ANG_DIST<0.01)
&&(FOV==0)
&&
(
(S1_PIXL3>0)  )
&&(  (S1_SATF3<1)
   ||(S1_SATF3>1))
&&(  (S1_SATF3<1)
   ||(S1_SATF3>1))
&&(  (S1_SATF3<1)
   ||(S1_SATF3>1))
&&(  (S1_SATF3<1)
   ||(S1_SATF3>1))
&&((T_DY_NT<0)||(T_DY_NT>16))
&&((T_SAA  <0)||(T_SAA  >16))
-> Standard Output From FTOOL xselect:
 
                         **  XSELECT V1.3   **
 
!> Enter session name >[xsel] screen
 
 Notes: XSELECT set up for      ASCA
 Keywords for time and pha are  TIME       PI
 Units of time are              s
 Default timing binsize =    16.00
 Keywords for images are          DETX       DETY
 Keywords for the WMAP are        DETX       DETY
 
 
 
        OBJECT   DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME   NEVENTS  S1CCDPOW
      1 XY_ARI   BRIGHT   LOW      29/01/96 18:44:15 0.77E+04     7079 0001
 
Processing file: /data/data22/seq_proc/33012010.005/ad33012010s100202l.unf
EXTRACTOR vers 2.0  11 Apr 1997.
 Skipping file: /data/data22/seq_proc/33012010.005/screen_work1001.xsl
 Writing events file
      0 events written to the output file
===============================================================================
   Grand Total      Good   Bad:  Region      Time     Phase       Cut
             0         0              0         0         0         0
   in       0.00 seconds
CLEANSIS_V1.6
    allocating image arrays...
 
 PROGRAM TO MAKE AN SIS SCIENCE FILE CLEANED OF ANOMALOUS PIXELS.
 
 * Anomalous pixels may consist of at least two populations.
 
 1. Persistent HOT pixels are removed by comparing to the chip mean.
 
 2. Flickering WARM pixels are removed by comparing to the cell mean.
 
 3. In faint areas (zero bgd), flickering pixels are removed with a
    cutoff threshold.
 
 Hints:
 Choose cell size and thresholds based on the expected background and the PSF.
 Use the DIRTYSIS option to examine the anomalous pixel spectra.
 Try a multiple pass clean:
     Choose a PHA cut to optimize the S/N of the flickering pixels,
     then a broad band clean.
 Be suspicious of extended source cleans.
 For very bright sources you may need to turn off the iteration option.
 
 See the help page for further info (fhelp cleansis)
 
 Poisson clean cell size         :            5
 Poisson probability threshold   :    0.631E-05
 Zero Bgd Cutoff threshold (>)   :            3
 Iterate                         :            T
 Dirtysis                        :            F
 
 Minimum PHA value (inclusive)   :            0
 Maximum PHA value (inclusive)   :         4095
 
    open output  file: /data/data22/seq_proc/33012010.005/screen_in_event.xsl
    reading data file: /data/data22/seq_proc/33012010.005/screen_out_event.xsl
    copying primary header to output file...
    making chip image...
 
 Total counts in chip images :            0
 
    copy bad pix array...
cleaning chip #           0
cleaning chip #           1
cleaning chip #           2
cleaning chip #           3
 
 Number of pixels rejected           :            0
 Number of (internal) image counts   :            0
 Number of image cts rejected (N, %) :            0      0.0000000
 
         By chip   :             0            1            2            3
 
 Pixels rejected   :             0            0            0            0
 
 Image counts      :             0            0            0            0
 Image cts rejected:             0            0            0            0
 Image cts rej (%) :          0.00         0.00         0.00         0.00
 
    filtering data...
 
 Total counts      :             0            0            0            0
 Total cts rejected:             0            0            0            0
 Total cts rej (%) :          0.00         0.00         0.00         0.00
 
 Number of clean counts accepted  :            0
 
    writing history cards...
    copying extensions...
    writing out hot pixs...
 
 Number of rejected pixels        :            0
 
    updating NEVENTS keywords...
    closing data file...
    closing clean file...
 Command not found; type ? for a command listing
!screen:ASCA > set mission ASCA
 
 Notes: XSELECT set up for      ASCA
 Keywords for time and pha are  TIME       PI
 Units of time are              s
 Default timing binsize =    16.00
 Keywords for images are          DETX       DETY
 Keywords for the WMAP are        DETX       DETY
 
!screen:ASCA > set datadir .
 
Setting data directory to /data/data22/seq_proc/33012010.005/
Setting mkf directory to /data/data22/seq_proc/33012010.005/
 
!screen:ASCA > read events ad33012010s100202l.unf
Got new instrument: SIS1
 
Setting: IMAGE binning    =    4
         WMAP binning     =    8
         Energy Column    =  PI
         Energy rebinning =    1
 
 
Getting Min and Max for Energy Column...
Got min and max for PI:     0   2047
 
Got the minimum time resolution of the read data:   4.0000
 Number of files read in:   1
 
******************** Observation Catalogue ********************
 
Data Directory is: /data/data22/seq_proc/33012010.005/
HK Directory is: /data/data22/seq_proc/33012010.005/
 
!screen:ASCA-SIS1-BRIGHT > select event "grade==0||grade==2||grade==3||grade==4"  save_file=no
!screen:ASCA-SIS1-BRIGHT > select mkf "@criteria.tmp" data_dir=. ASCA_mkf_def_expr=ft*.mkf
!screen:ASCA-SIS1-BRIGHT > extract events
!screen:ASCA-SIS1-BRIGHT > sisclean saoimage=no sis_plot=no clean=2 cellsize=5 log_prob=-5.24 bkg_thr=3 clean_phalow=0 clean_phahi=4095
!screen:ASCA-SIS1-BRIGHT > save clean outfile=ad33012010s100202l.evt use_events=no
 Wrote cleaned events file to ad33012010s100202l.evt                                                                                                                                                                                                            
 
!screen:ASCA-SIS1-BRIGHT > exit save_session=no
-> Deleting ad33012010s100202l.evt since it contains 0 events
-> Filtering ad33012010s100212l.unf into ad33012010s100212l.evt
-> Using the following selection criteria:
(SAA==0)
&&(BR_EARTH>20)
&&(ELV>10)
&&(COR>6)
&&(ACS==0)
&&(ANG_DIST>0)&& (ANG_DIST<0.01)
&&(FOV==0)
&&
(
(S1_PIXL3>0)  )
&&(  (S1_SATF3<1)
   ||(S1_SATF3>1))
&&(  (S1_SATF3<1)
   ||(S1_SATF3>1))
&&(  (S1_SATF3<1)
   ||(S1_SATF3>1))
&&(  (S1_SATF3<1)
   ||(S1_SATF3>1))
&&((T_DY_NT<0)||(T_DY_NT>16))
&&((T_SAA  <0)||(T_SAA  >16))
-> Standard Output From FTOOL xselect:
 
                         **  XSELECT V1.3   **
 
!> Enter session name >[xsel] screen
 
 Notes: XSELECT set up for      ASCA
 Keywords for time and pha are  TIME       PI
 Units of time are              s
 Default timing binsize =    16.00
 Keywords for images are          DETX       DETY
 Keywords for the WMAP are        DETX       DETY
 
 
 
        OBJECT   DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME   NEVENTS  S1CCDPOW
      1 XY_ARI   BRIGHT2  LOW      29/01/96 18:44:15 0.77E+04     7137 0001
 
Processing file: /data/data22/seq_proc/33012010.005/ad33012010s100212l.unf
EXTRACTOR vers 2.0  11 Apr 1997.
 Skipping file: /data/data22/seq_proc/33012010.005/screen_work1001.xsl
 Writing events file
      0 events written to the output file
===============================================================================
   Grand Total      Good   Bad:  Region      Time     Phase       Cut
             0         0              0         0         0         0
   in       0.00 seconds
CLEANSIS_V1.6
    allocating image arrays...
 
 PROGRAM TO MAKE AN SIS SCIENCE FILE CLEANED OF ANOMALOUS PIXELS.
 
 * Anomalous pixels may consist of at least two populations.
 
 1. Persistent HOT pixels are removed by comparing to the chip mean.
 
 2. Flickering WARM pixels are removed by comparing to the cell mean.
 
 3. In faint areas (zero bgd), flickering pixels are removed with a
    cutoff threshold.
 
 Hints:
 Choose cell size and thresholds based on the expected background and the PSF.
 Use the DIRTYSIS option to examine the anomalous pixel spectra.
 Try a multiple pass clean:
     Choose a PHA cut to optimize the S/N of the flickering pixels,
     then a broad band clean.
 Be suspicious of extended source cleans.
 For very bright sources you may need to turn off the iteration option.
 
 See the help page for further info (fhelp cleansis)
 
 Poisson clean cell size         :            5
 Poisson probability threshold   :    0.631E-05
 Zero Bgd Cutoff threshold (>)   :            3
 Iterate                         :            T
 Dirtysis                        :            F
 
 Minimum PHA value (inclusive)   :            0
 Maximum PHA value (inclusive)   :         4095
 
    open output  file: /data/data22/seq_proc/33012010.005/screen_in_event.xsl
    reading data file: /data/data22/seq_proc/33012010.005/screen_out_event.xsl
    copying primary header to output file...
    making chip image...
 
 Total counts in chip images :            0
 
    copy bad pix array...
cleaning chip #           0
cleaning chip #           1
cleaning chip #           2
cleaning chip #           3
 
 Number of pixels rejected           :            0
 Number of (internal) image counts   :            0
 Number of image cts rejected (N, %) :            0      0.0000000
 
         By chip   :             0            1            2            3
 
 Pixels rejected   :             0            0            0            0
 
 Image counts      :             0            0            0            0
 Image cts rejected:             0            0            0            0
 Image cts rej (%) :          0.00         0.00         0.00         0.00
 
    filtering data...
 
 Total counts      :             0            0            0            0
 Total cts rejected:             0            0            0            0
 Total cts rej (%) :          0.00         0.00         0.00         0.00
 
 Number of clean counts accepted  :            0
 
    writing history cards...
    copying extensions...
    writing out hot pixs...
 
 Number of rejected pixels        :            0
 
    updating NEVENTS keywords...
    closing data file...
    closing clean file...
 Command not found; type ? for a command listing
!screen:ASCA > set mission ASCA
 
 Notes: XSELECT set up for      ASCA
 Keywords for time and pha are  TIME       PI
 Units of time are              s
 Default timing binsize =    16.00
 Keywords for images are          DETX       DETY
 Keywords for the WMAP are        DETX       DETY
 
!screen:ASCA > set datadir .
 
Setting data directory to /data/data22/seq_proc/33012010.005/
Setting mkf directory to /data/data22/seq_proc/33012010.005/
 
!screen:ASCA > read events ad33012010s100212l.unf
Got new instrument: SIS1
 
Setting: IMAGE binning    =    4
         WMAP binning     =    8
         Energy Column    =  PI
         Energy rebinning =    1
 
 
Getting Min and Max for Energy Column...
Got min and max for PI:     0   4095
 
Got the minimum time resolution of the read data:   4.0000
 Number of files read in:   1
 
******************** Observation Catalogue ********************
 
Data Directory is: /data/data22/seq_proc/33012010.005/
HK Directory is: /data/data22/seq_proc/33012010.005/
 
!screen:ASCA-SIS1-BRIGHT2 > select event "grade==0||grade==2||grade==3||grade==4"  save_file=no
!screen:ASCA-SIS1-BRIGHT2 > select mkf "@criteria.tmp" data_dir=. ASCA_mkf_def_expr=ft*.mkf
!screen:ASCA-SIS1-BRIGHT2 > extract events
!screen:ASCA-SIS1-BRIGHT2 > sisclean saoimage=no sis_plot=no clean=2 cellsize=5 log_prob=-5.24 bkg_thr=3 clean_phalow=0 clean_phahi=4095
!screen:ASCA-SIS1-BRIGHT2 > save clean outfile=ad33012010s100212l.evt use_events=no
 Wrote cleaned events file to ad33012010s100212l.evt                                                                                                                                                                                                            
 
!screen:ASCA-SIS1-BRIGHT2 > exit save_session=no
-> Deleting ad33012010s100212l.evt since it contains 0 events
-> Skipping ad33012010s100301m.unf because of mode
-> Filtering ad33012010s100302m.unf into ad33012010s100302m.evt
-> Standard Output From FTOOL fstatistic:
 The sum of the selected column is                   473.22016
 The mean of the selected column is                  52.580018
 The standard deviation of the selected column is    19.390073
 The minimum of selected column is                   34.187603
 The maximum of selected column is                   96.937790
 The number of points used in calculation is                9
-> Using the following selection criteria:
(SAA==0)
&&(BR_EARTH>20)
&&(ELV>10)
&&(COR>6)
&&(ACS==0)
&&(ANG_DIST>0)&& (ANG_DIST<0.01)
&&(FOV==0)
&&
(
(S1_PIXL3>0.0 && S1_PIXL3<110.7 )  )
&&(  (S1_SATF3<1)
   ||(S1_SATF3>1))
&&(  (S1_SATF3<1)
   ||(S1_SATF3>1))
&&(  (S1_SATF3<1)
   ||(S1_SATF3>1))
&&(  (S1_SATF3<1)
   ||(S1_SATF3>1))
&&((T_DY_NT<0)||(T_DY_NT>16))
&&((T_SAA  <0)||(T_SAA  >16))
-> Standard Output From FTOOL xselect:
 
                         **  XSELECT V1.3   **
 
!> Enter session name >[xsel] screen
 
 Notes: XSELECT set up for      ASCA
 Keywords for time and pha are  TIME       PI
 Units of time are              s
 Default timing binsize =    16.00
 Keywords for images are          DETX       DETY
 Keywords for the WMAP are        DETX       DETY
 
 
 
        OBJECT   DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME   NEVENTS  S1CCDPOW
      1 XY_ARI   BRIGHT   MEDIUM   29/01/96 17:30:23 0.32E+04     4520 0001
 
Processing file: /data/data22/seq_proc/33012010.005/ad33012010s100302m.unf
EXTRACTOR vers 2.0  11 Apr 1997.
 Doing file: /data/data22/seq_proc/33012010.005/screen_work1001.xsl
          Total      Good    Bad: Region      Time     Phase       Cut
           4258      1222              0      3036         0         0
 Writing events file
   1222 events written to the output file
===============================================================================
   Grand Total      Good   Bad:  Region      Time     Phase       Cut
          4258      1222              0      3036         0         0
   in     791.73 seconds
CLEANSIS_V1.6
    allocating image arrays...
 
 PROGRAM TO MAKE AN SIS SCIENCE FILE CLEANED OF ANOMALOUS PIXELS.
 
 * Anomalous pixels may consist of at least two populations.
 
 1. Persistent HOT pixels are removed by comparing to the chip mean.
 
 2. Flickering WARM pixels are removed by comparing to the cell mean.
 
 3. In faint areas (zero bgd), flickering pixels are removed with a
    cutoff threshold.
 
 Hints:
 Choose cell size and thresholds based on the expected background and the PSF.
 Use the DIRTYSIS option to examine the anomalous pixel spectra.
 Try a multiple pass clean:
     Choose a PHA cut to optimize the S/N of the flickering pixels,
     then a broad band clean.
 Be suspicious of extended source cleans.
 For very bright sources you may need to turn off the iteration option.
 
 See the help page for further info (fhelp cleansis)
 
 Poisson clean cell size         :            5
 Poisson probability threshold   :    0.631E-05
 Zero Bgd Cutoff threshold (>)   :            3
 Iterate                         :            T
 Dirtysis                        :            F
 
 Minimum PHA value (inclusive)   :            0
 Maximum PHA value (inclusive)   :         4095
 
    open output  file: /data/data22/seq_proc/33012010.005/screen_in_event.xsl
    reading data file: /data/data22/seq_proc/33012010.005/screen_out_event.xsl
    copying primary header to output file...
    making chip image...
 
 Total counts in chip images :         1222
 
    copy bad pix array...
cleaning chip #           0
cleaning chip #           1
cleaning chip #           2
cleaning chip #           3
 Hot pixels & counts                   :               6        1050
 Flickering pixels iter, pixels & cnts :   1           2          19
 
 Number of pixels rejected           :            8
 Number of (internal) image counts   :         1222
 Number of image cts rejected (N, %) :         1069     87.4795380
 
         By chip   :             0            1            2            3
 
 Pixels rejected   :             0            0            0            8
 
 Image counts      :             0            0            0         1222
 Image cts rejected:             0            0            0         1069
 Image cts rej (%) :          0.00         0.00         0.00        87.48
 
    filtering data...
 
 Total counts      :             0            0            0         1222
 Total cts rejected:             0            0            0         1069
 Total cts rej (%) :          0.00         0.00         0.00        87.48
 
 Number of clean counts accepted  :          153
 
    writing history cards...
    copying extensions...
    writing out hot pixs...
 
 Number of rejected pixels        :            8
 
    updating NEVENTS keywords...
    closing data file...
    closing clean file...
 Command not found; type ? for a command listing
!screen:ASCA > set mission ASCA
 
 Notes: XSELECT set up for      ASCA
 Keywords for time and pha are  TIME       PI
 Units of time are              s
 Default timing binsize =    16.00
 Keywords for images are          DETX       DETY
 Keywords for the WMAP are        DETX       DETY
 
!screen:ASCA > set datadir .
 
Setting data directory to /data/data22/seq_proc/33012010.005/
Setting mkf directory to /data/data22/seq_proc/33012010.005/
 
!screen:ASCA > read events ad33012010s100302m.unf
Got new instrument: SIS1
 
Setting: IMAGE binning    =    4
         WMAP binning     =    8
         Energy Column    =  PI
         Energy rebinning =    1
 
 
Getting Min and Max for Energy Column...
Got min and max for PI:     0   2047
 
Got the minimum time resolution of the read data:   4.0000
 Number of files read in:   1
 
******************** Observation Catalogue ********************
 
Data Directory is: /data/data22/seq_proc/33012010.005/
HK Directory is: /data/data22/seq_proc/33012010.005/
 
!screen:ASCA-SIS1-BRIGHT > select event "grade==0||grade==2||grade==3||grade==4"  save_file=no
!screen:ASCA-SIS1-BRIGHT > select mkf "@criteria.tmp" data_dir=. ASCA_mkf_def_expr=ft*.mkf
!screen:ASCA-SIS1-BRIGHT > extract events
!screen:ASCA-SIS1-BRIGHT > sisclean saoimage=no sis_plot=no clean=2 cellsize=5 log_prob=-5.24 bkg_thr=3 clean_phalow=0 clean_phahi=4095
!screen:ASCA-SIS1-BRIGHT > save clean outfile=ad33012010s100302m.evt use_events=no
 Wrote cleaned events file to ad33012010s100302m.evt                                                                                                                                                                                                            
 
!screen:ASCA-SIS1-BRIGHT > exit save_session=no
-> Filtering ad33012010s100312m.unf into ad33012010s100312m.evt
-> Standard Output From FTOOL fstatistic:
 The sum of the selected column is                   473.22016
 The mean of the selected column is                  52.580018
 The standard deviation of the selected column is    19.390073
 The minimum of selected column is                   34.187603
 The maximum of selected column is                   96.937790
 The number of points used in calculation is                9
-> Using the following selection criteria:
(SAA==0)
&&(BR_EARTH>20)
&&(ELV>10)
&&(COR>6)
&&(ACS==0)
&&(ANG_DIST>0)&& (ANG_DIST<0.01)
&&(FOV==0)
&&
(
(S1_PIXL3>0.0 && S1_PIXL3<110.7 )  )
&&(  (S1_SATF3<1)
   ||(S1_SATF3>1))
&&(  (S1_SATF3<1)
   ||(S1_SATF3>1))
&&(  (S1_SATF3<1)
   ||(S1_SATF3>1))
&&(  (S1_SATF3<1)
   ||(S1_SATF3>1))
&&((T_DY_NT<0)||(T_DY_NT>16))
&&((T_SAA  <0)||(T_SAA  >16))
-> Standard Output From FTOOL xselect:
 
                         **  XSELECT V1.3   **
 
!> Enter session name >[xsel] screen
 
 Notes: XSELECT set up for      ASCA
 Keywords for time and pha are  TIME       PI
 Units of time are              s
 Default timing binsize =    16.00
 Keywords for images are          DETX       DETY
 Keywords for the WMAP are        DETX       DETY
 
 
 
        OBJECT   DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME   NEVENTS  S1CCDPOW
      1 XY_ARI   BRIGHT2  MEDIUM   29/01/96 17:30:23 0.32E+04     4559 0001
 
Processing file: /data/data22/seq_proc/33012010.005/ad33012010s100312m.unf
EXTRACTOR vers 2.0  11 Apr 1997.
 Doing file: /data/data22/seq_proc/33012010.005/screen_work1001.xsl
          Total      Good    Bad: Region      Time     Phase       Cut
           4280      1227              0      3053         0         0
 Writing events file
   1227 events written to the output file
===============================================================================
   Grand Total      Good   Bad:  Region      Time     Phase       Cut
          4280      1227              0      3053         0         0
   in     791.73 seconds
CLEANSIS_V1.6
    allocating image arrays...
 
 PROGRAM TO MAKE AN SIS SCIENCE FILE CLEANED OF ANOMALOUS PIXELS.
 
 * Anomalous pixels may consist of at least two populations.
 
 1. Persistent HOT pixels are removed by comparing to the chip mean.
 
 2. Flickering WARM pixels are removed by comparing to the cell mean.
 
 3. In faint areas (zero bgd), flickering pixels are removed with a
    cutoff threshold.
 
 Hints:
 Choose cell size and thresholds based on the expected background and the PSF.
 Use the DIRTYSIS option to examine the anomalous pixel spectra.
 Try a multiple pass clean:
     Choose a PHA cut to optimize the S/N of the flickering pixels,
     then a broad band clean.
 Be suspicious of extended source cleans.
 For very bright sources you may need to turn off the iteration option.
 
 See the help page for further info (fhelp cleansis)
 
 Poisson clean cell size         :            5
 Poisson probability threshold   :    0.631E-05
 Zero Bgd Cutoff threshold (>)   :            3
 Iterate                         :            T
 Dirtysis                        :            F
 
 Minimum PHA value (inclusive)   :            0
 Maximum PHA value (inclusive)   :         4095
 
    open output  file: /data/data22/seq_proc/33012010.005/screen_in_event.xsl
    reading data file: /data/data22/seq_proc/33012010.005/screen_out_event.xsl
    copying primary header to output file...
    making chip image...
 
 Total counts in chip images :         1227
 
    copy bad pix array...
cleaning chip #           0
cleaning chip #           1
cleaning chip #           2
cleaning chip #           3
 Hot pixels & counts                   :               6        1050
 Flickering pixels iter, pixels & cnts :   1           2          19
 
 Number of pixels rejected           :            8
 Number of (internal) image counts   :         1227
 Number of image cts rejected (N, %) :         1069     87.1230621
 
         By chip   :             0            1            2            3
 
 Pixels rejected   :             0            0            0            8
 
 Image counts      :             0            0            0         1227
 Image cts rejected:             0            0            0         1069
 Image cts rej (%) :          0.00         0.00         0.00        87.12
 
    filtering data...
 
 Total counts      :             0            0            0         1227
 Total cts rejected:             0            0            0         1069
 Total cts rej (%) :          0.00         0.00         0.00        87.12
 
 Number of clean counts accepted  :          158
 
    writing history cards...
    copying extensions...
    writing out hot pixs...
 
 Number of rejected pixels        :            8
 
    updating NEVENTS keywords...
    closing data file...
    closing clean file...
 Command not found; type ? for a command listing
!screen:ASCA > set mission ASCA
 
 Notes: XSELECT set up for      ASCA
 Keywords for time and pha are  TIME       PI
 Units of time are              s
 Default timing binsize =    16.00
 Keywords for images are          DETX       DETY
 Keywords for the WMAP are        DETX       DETY
 
!screen:ASCA > set datadir .
 
Setting data directory to /data/data22/seq_proc/33012010.005/
Setting mkf directory to /data/data22/seq_proc/33012010.005/
 
!screen:ASCA > read events ad33012010s100312m.unf
Got new instrument: SIS1
 
Setting: IMAGE binning    =    4
         WMAP binning     =    8
         Energy Column    =  PI
         Energy rebinning =    1
 
 
Getting Min and Max for Energy Column...
Got min and max for PI:     0   4095
 
Got the minimum time resolution of the read data:   4.0000
 Number of files read in:   1
 
******************** Observation Catalogue ********************
 
Data Directory is: /data/data22/seq_proc/33012010.005/
HK Directory is: /data/data22/seq_proc/33012010.005/
 
!screen:ASCA-SIS1-BRIGHT2 > select event "grade==0||grade==2||grade==3||grade==4"  save_file=no
!screen:ASCA-SIS1-BRIGHT2 > select mkf "@criteria.tmp" data_dir=. ASCA_mkf_def_expr=ft*.mkf
!screen:ASCA-SIS1-BRIGHT2 > extract events
!screen:ASCA-SIS1-BRIGHT2 > sisclean saoimage=no sis_plot=no clean=2 cellsize=5 log_prob=-5.24 bkg_thr=3 clean_phalow=0 clean_phahi=4095
!screen:ASCA-SIS1-BRIGHT2 > save clean outfile=ad33012010s100312m.evt use_events=no
 Wrote cleaned events file to ad33012010s100312m.evt                                                                                                                                                                                                            
 
!screen:ASCA-SIS1-BRIGHT2 > exit save_session=no
-> Filtering ad33012010g200170h.unf into ad33012010g200170h.evt
-> Fetching GIS2_REGION256.4
-> Using the following selection criteria:
(SAA==0)&&
(COR>4)&&
(G2_H0+G2_H2+G3_H0+G3_H2<45)&&
(G2_H0+G2_H2+G3_H0+G3_H2<0.45*COR**2-13*COR+125)&&
(RBM_CONT<100)&&
(ELV>5)&&
(ACS==0)&&
(ANG_DIST>0)&& (ANG_DIST<0.01)&&
(G2_L1>0)
-> Standard Output From FTOOL xselect:
 
                         **  XSELECT V1.3   **
 
!> Enter session name >[xsel] screen
 
 Notes: XSELECT set up for      ASCA
 Keywords for time and pha are  TIME       PI
 Units of time are              s
 Default timing binsize =    16.00
 Keywords for images are          DETX       DETY
 Keywords for the WMAP are        DETX       DETY
 
 
 
        OBJECT   DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME   NEVENTS  PHA_BINS
      1 XY_ARI   PH       HIGH     29/01/96 17:43:01 0.48E+04     4638     1024
 
EXTRACTOR vers 2.0  11 Apr 1997.
 Doing file: /data/data22/seq_proc/33012010.005/ad33012010g200170h.unf
          Total      Good    Bad: Region      Time     Phase       Cut
           4638      1554           2709       375         0         0
 Writing events file
   1554 events written to the output file
===============================================================================
   Grand Total      Good   Bad:  Region      Time     Phase       Cut
          4638      1554           2709       375         0         0
   in    3814.01 seconds
Infile # of rows    Outfile # of rows    # filtered
----------------    -----------------    ----------
        1554                1358               196
 Command not found; type ? for a command listing
!screen:ASCA > set mission ASCA
 
 Notes: XSELECT set up for      ASCA
 Keywords for time and pha are  TIME       PI
 Units of time are              s
 Default timing binsize =    16.00
 Keywords for images are          DETX       DETY
 Keywords for the WMAP are        DETX       DETY
 
!screen:ASCA > set datadir .
 
Setting data directory to /data/data22/seq_proc/33012010.005/
Setting mkf directory to /data/data22/seq_proc/33012010.005/
 
!screen:ASCA > read events ad33012010g200170h.unf
Got new instrument: GIS2
 
Setting: IMAGE binning    =    1
         WMAP binning     =    1
         Energy Column    =  PI
         Energy rebinning =    1
 
 
Getting Min and Max for Energy Column...
Got min and max for PI:     0   1023
 
Got the minimum time resolution of the read data:  0.62500E-01
 Number of files read in:   1
 
******************** Observation Catalogue ********************
 
Data Directory is: /data/data22/seq_proc/33012010.005/
HK Directory is: /data/data22/seq_proc/33012010.005/
 
!screen:ASCA-GIS2-PH > filter region GIS2_REGION256.4
!screen:ASCA-GIS2-PH > select mkf "@criteria.tmp" data_dir=. ASCA_mkf_def_expr=ft*.mkf
!screen:ASCA-GIS2-PH > extract events
!screen:ASCA-GIS2-PH > gisclean
Using table:/opt/local/ftools/ftools.4.0.c/SunOS_5.4_sparc/refdata/rti_gis_1024_040693.fits
!screen:ASCA-GIS2-PH > save clean outfile=ad33012010g200170h.evt use_events=no
!screen:ASCA-GIS2-PH > exit save_session=no
-> Setting NEVENTS to 1358 in ad33012010g200170h.unf
-> Filtering ad33012010g200270l.unf into ad33012010g200270l.evt
-> GIS2_REGION256.4 already present in current directory
-> Using the following selection criteria:
(SAA==0)&&
(COR>4)&&
(G2_H0+G2_H2+G3_H0+G3_H2<45)&&
(G2_H0+G2_H2+G3_H0+G3_H2<0.45*COR**2-13*COR+125)&&
(RBM_CONT<100)&&
(ELV>5)&&
(ACS==0)&&
(ANG_DIST>0)&& (ANG_DIST<0.01)&&
(G2_L1>0)
-> Standard Output From FTOOL xselect:
 
                         **  XSELECT V1.3   **
 
!> Enter session name >[xsel] screen
 
 Notes: XSELECT set up for      ASCA
 Keywords for time and pha are  TIME       PI
 Units of time are              s
 Default timing binsize =    16.00
 Keywords for images are          DETX       DETY
 Keywords for the WMAP are        DETX       DETY
 
 
 
        OBJECT   DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME   NEVENTS  PHA_BINS
      1 XY_ARI   PH       LOW      29/01/96 18:46:29 0.61E+04     3925     1024
 
EXTRACTOR vers 2.0  11 Apr 1997.
 Doing file: /data/data22/seq_proc/33012010.005/ad33012010g200270l.unf
          Total      Good    Bad: Region      Time     Phase       Cut
           3925        16           2848      1061         0         0
 Writing events file
     16 events written to the output file
===============================================================================
   Grand Total      Good   Bad:  Region      Time     Phase       Cut
          3925        16           2848      1061         0         0
   in      31.96 seconds
Infile # of rows    Outfile # of rows    # filtered
----------------    -----------------    ----------
          16                  16                 0
 Command not found; type ? for a command listing
!screen:ASCA > set mission ASCA
 
 Notes: XSELECT set up for      ASCA
 Keywords for time and pha are  TIME       PI
 Units of time are              s
 Default timing binsize =    16.00
 Keywords for images are          DETX       DETY
 Keywords for the WMAP are        DETX       DETY
 
!screen:ASCA > set datadir .
 
Setting data directory to /data/data22/seq_proc/33012010.005/
Setting mkf directory to /data/data22/seq_proc/33012010.005/
 
!screen:ASCA > read events ad33012010g200270l.unf
Got new instrument: GIS2
 
Setting: IMAGE binning    =    1
         WMAP binning     =    1
         Energy Column    =  PI
         Energy rebinning =    1
 
 
Getting Min and Max for Energy Column...
Got min and max for PI:     0   1023
 
Got the minimum time resolution of the read data:   2.0000
 Number of files read in:   1
 
******************** Observation Catalogue ********************
 
Data Directory is: /data/data22/seq_proc/33012010.005/
HK Directory is: /data/data22/seq_proc/33012010.005/
 
!screen:ASCA-GIS2-PH > filter region GIS2_REGION256.4
!screen:ASCA-GIS2-PH > select mkf "@criteria.tmp" data_dir=. ASCA_mkf_def_expr=ft*.mkf
!screen:ASCA-GIS2-PH > extract events
!screen:ASCA-GIS2-PH > gisclean
Using table:/opt/local/ftools/ftools.4.0.c/SunOS_5.4_sparc/refdata/rti_gis_1024_040693.fits
!screen:ASCA-GIS2-PH > save clean outfile=ad33012010g200270l.evt use_events=no
!screen:ASCA-GIS2-PH > exit save_session=no
-> Filtering ad33012010g200370m.unf into ad33012010g200370m.evt
-> GIS2_REGION256.4 already present in current directory
-> Using the following selection criteria:
(SAA==0)&&
(COR>4)&&
(G2_H0+G2_H2+G3_H0+G3_H2<45)&&
(G2_H0+G2_H2+G3_H0+G3_H2<0.45*COR**2-13*COR+125)&&
(RBM_CONT<100)&&
(ELV>5)&&
(ACS==0)&&
(ANG_DIST>0)&& (ANG_DIST<0.01)&&
(G2_L1>0)
-> Standard Output From FTOOL xselect:
 
                         **  XSELECT V1.3   **
 
!> Enter session name >[xsel] screen
 
 Notes: XSELECT set up for      ASCA
 Keywords for time and pha are  TIME       PI
 Units of time are              s
 Default timing binsize =    16.00
 Keywords for images are          DETX       DETY
 Keywords for the WMAP are        DETX       DETY
 
 
 
        OBJECT   DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME   NEVENTS  PHA_BINS
      1 XY_ARI   PH       MEDIUM   29/01/96 17:30:29 0.33E+04     2903     1024
 
EXTRACTOR vers 2.0  11 Apr 1997.
 Doing file: /data/data22/seq_proc/33012010.005/ad33012010g200370m.unf
          Total      Good    Bad: Region      Time     Phase       Cut
           2903       614           1692       597         0         0
 Writing events file
    614 events written to the output file
===============================================================================
   Grand Total      Good   Bad:  Region      Time     Phase       Cut
          2903       614           1692       597         0         0
   in    1344.04 seconds
Infile # of rows    Outfile # of rows    # filtered
----------------    -----------------    ----------
         614                 547                67
 Command not found; type ? for a command listing
!screen:ASCA > set mission ASCA
 
 Notes: XSELECT set up for      ASCA
 Keywords for time and pha are  TIME       PI
 Units of time are              s
 Default timing binsize =    16.00
 Keywords for images are          DETX       DETY
 Keywords for the WMAP are        DETX       DETY
 
!screen:ASCA > set datadir .
 
Setting data directory to /data/data22/seq_proc/33012010.005/
Setting mkf directory to /data/data22/seq_proc/33012010.005/
 
!screen:ASCA > read events ad33012010g200370m.unf
Got new instrument: GIS2
 
Setting: IMAGE binning    =    1
         WMAP binning     =    1
         Energy Column    =  PI
         Energy rebinning =    1
 
 
Getting Min and Max for Energy Column...
Got min and max for PI:     0   1023
 
Got the minimum time resolution of the read data:  0.50000
 Number of files read in:   1
 
******************** Observation Catalogue ********************
 
Data Directory is: /data/data22/seq_proc/33012010.005/
HK Directory is: /data/data22/seq_proc/33012010.005/
 
!screen:ASCA-GIS2-PH > filter region GIS2_REGION256.4
!screen:ASCA-GIS2-PH > select mkf "@criteria.tmp" data_dir=. ASCA_mkf_def_expr=ft*.mkf
!screen:ASCA-GIS2-PH > extract events
!screen:ASCA-GIS2-PH > gisclean
Using table:/opt/local/ftools/ftools.4.0.c/SunOS_5.4_sparc/refdata/rti_gis_1024_040693.fits
!screen:ASCA-GIS2-PH > save clean outfile=ad33012010g200370m.evt use_events=no
!screen:ASCA-GIS2-PH > exit save_session=no
-> Setting NEVENTS to 547 in ad33012010g200370m.unf
-> Filtering ad33012010g300170h.unf into ad33012010g300170h.evt
-> Fetching GIS3_REGION256.4
-> Using the following selection criteria:
(SAA==0)&&
(COR>4)&&
(G2_H0+G2_H2+G3_H0+G3_H2<45)&&
(G2_H0+G2_H2+G3_H0+G3_H2<0.45*COR**2-13*COR+125)&&
(RBM_CONT<100)&&
(ELV>5)&&
(ACS==0)&&
(ANG_DIST>0)&& (ANG_DIST<0.01)&&
(G3_L1>0)
-> Standard Output From FTOOL xselect:
 
                         **  XSELECT V1.3   **
 
!> Enter session name >[xsel] screen
 
 Notes: XSELECT set up for      ASCA
 Keywords for time and pha are  TIME       PI
 Units of time are              s
 Default timing binsize =    16.00
 Keywords for images are          DETX       DETY
 Keywords for the WMAP are        DETX       DETY
 
 
 
        OBJECT   DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME   NEVENTS  PHA_BINS
      1 XY_ARI   PH       HIGH     29/01/96 17:43:01 0.48E+04     4397     1024
 
EXTRACTOR vers 2.0  11 Apr 1997.
 Doing file: /data/data22/seq_proc/33012010.005/ad33012010g300170h.unf
          Total      Good    Bad: Region      Time     Phase       Cut
           4397      1786           2233       378         0         0
 Writing events file
   1786 events written to the output file
===============================================================================
   Grand Total      Good   Bad:  Region      Time     Phase       Cut
          4397      1786           2233       378         0         0
   in    3811.96 seconds
Infile # of rows    Outfile # of rows    # filtered
----------------    -----------------    ----------
        1786                1552               234
 Command not found; type ? for a command listing
!screen:ASCA > set mission ASCA
 
 Notes: XSELECT set up for      ASCA
 Keywords for time and pha are  TIME       PI
 Units of time are              s
 Default timing binsize =    16.00
 Keywords for images are          DETX       DETY
 Keywords for the WMAP are        DETX       DETY
 
!screen:ASCA > set datadir .
 
Setting data directory to /data/data22/seq_proc/33012010.005/
Setting mkf directory to /data/data22/seq_proc/33012010.005/
 
!screen:ASCA > read events ad33012010g300170h.unf
Got new instrument: GIS3
 
Setting: IMAGE binning    =    1
         WMAP binning     =    1
         Energy Column    =  PI
         Energy rebinning =    1
 
 
Getting Min and Max for Energy Column...
Got min and max for PI:     0   1023
 
Got the minimum time resolution of the read data:  0.62500E-01
 Number of files read in:   1
 
******************** Observation Catalogue ********************
 
Data Directory is: /data/data22/seq_proc/33012010.005/
HK Directory is: /data/data22/seq_proc/33012010.005/
 
!screen:ASCA-GIS3-PH > filter region GIS3_REGION256.4
!screen:ASCA-GIS3-PH > select mkf "@criteria.tmp" data_dir=. ASCA_mkf_def_expr=ft*.mkf
!screen:ASCA-GIS3-PH > extract events
!screen:ASCA-GIS3-PH > gisclean
Using table:/opt/local/ftools/ftools.4.0.c/SunOS_5.4_sparc/refdata/rti_gis_1024_040693.fits
!screen:ASCA-GIS3-PH > save clean outfile=ad33012010g300170h.evt use_events=no
!screen:ASCA-GIS3-PH > exit save_session=no
-> Setting NEVENTS to 1552 in ad33012010g300170h.unf
-> Filtering ad33012010g300270l.unf into ad33012010g300270l.evt
-> GIS3_REGION256.4 already present in current directory
-> Using the following selection criteria:
(SAA==0)&&
(COR>4)&&
(G2_H0+G2_H2+G3_H0+G3_H2<45)&&
(G2_H0+G2_H2+G3_H0+G3_H2<0.45*COR**2-13*COR+125)&&
(RBM_CONT<100)&&
(ELV>5)&&
(ACS==0)&&
(ANG_DIST>0)&& (ANG_DIST<0.01)&&
(G3_L1>0)
-> Standard Output From FTOOL xselect:
 
                         **  XSELECT V1.3   **
 
!> Enter session name >[xsel] screen
 
 Notes: XSELECT set up for      ASCA
 Keywords for time and pha are  TIME       PI
 Units of time are              s
 Default timing binsize =    16.00
 Keywords for images are          DETX       DETY
 Keywords for the WMAP are        DETX       DETY
 
 
 
        OBJECT   DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME   NEVENTS  PHA_BINS
      1 XY_ARI   PH       LOW      29/01/96 18:46:29 0.60E+04     3589     1024
 
EXTRACTOR vers 2.0  11 Apr 1997.
 Doing file: /data/data22/seq_proc/33012010.005/ad33012010g300270l.unf
          Total      Good    Bad: Region      Time     Phase       Cut
           3589        18           2479      1092         0         0
 Writing events file
     18 events written to the output file
===============================================================================
   Grand Total      Good   Bad:  Region      Time     Phase       Cut
          3589        18           2479      1092         0         0
   in      31.96 seconds
Infile # of rows    Outfile # of rows    # filtered
----------------    -----------------    ----------
          18                  18                 0
 Command not found; type ? for a command listing
!screen:ASCA > set mission ASCA
 
 Notes: XSELECT set up for      ASCA
 Keywords for time and pha are  TIME       PI
 Units of time are              s
 Default timing binsize =    16.00
 Keywords for images are          DETX       DETY
 Keywords for the WMAP are        DETX       DETY
 
!screen:ASCA > set datadir .
 
Setting data directory to /data/data22/seq_proc/33012010.005/
Setting mkf directory to /data/data22/seq_proc/33012010.005/
 
!screen:ASCA > read events ad33012010g300270l.unf
Got new instrument: GIS3
 
Setting: IMAGE binning    =    1
         WMAP binning     =    1
         Energy Column    =  PI
         Energy rebinning =    1
 
 
Getting Min and Max for Energy Column...
Got min and max for PI:     0   1023
 
Got the minimum time resolution of the read data:   2.0000
 Number of files read in:   1
 
******************** Observation Catalogue ********************
 
Data Directory is: /data/data22/seq_proc/33012010.005/
HK Directory is: /data/data22/seq_proc/33012010.005/
 
!screen:ASCA-GIS3-PH > filter region GIS3_REGION256.4
!screen:ASCA-GIS3-PH > select mkf "@criteria.tmp" data_dir=. ASCA_mkf_def_expr=ft*.mkf
!screen:ASCA-GIS3-PH > extract events
!screen:ASCA-GIS3-PH > gisclean
Using table:/opt/local/ftools/ftools.4.0.c/SunOS_5.4_sparc/refdata/rti_gis_1024_040693.fits
!screen:ASCA-GIS3-PH > save clean outfile=ad33012010g300270l.evt use_events=no
!screen:ASCA-GIS3-PH > exit save_session=no
-> Filtering ad33012010g300370m.unf into ad33012010g300370m.evt
-> GIS3_REGION256.4 already present in current directory
-> Using the following selection criteria:
(SAA==0)&&
(COR>4)&&
(G2_H0+G2_H2+G3_H0+G3_H2<45)&&
(G2_H0+G2_H2+G3_H0+G3_H2<0.45*COR**2-13*COR+125)&&
(RBM_CONT<100)&&
(ELV>5)&&
(ACS==0)&&
(ANG_DIST>0)&& (ANG_DIST<0.01)&&
(G3_L1>0)
-> Standard Output From FTOOL xselect:
 
                         **  XSELECT V1.3   **
 
!> Enter session name >[xsel] screen
 
 Notes: XSELECT set up for      ASCA
 Keywords for time and pha are  TIME       PI
 Units of time are              s
 Default timing binsize =    16.00
 Keywords for images are          DETX       DETY
 Keywords for the WMAP are        DETX       DETY
 
 
 
        OBJECT   DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME   NEVENTS  PHA_BINS
      1 XY_ARI   PH       MEDIUM   29/01/96 17:30:29 0.33E+04     2867     1024
 
EXTRACTOR vers 2.0  11 Apr 1997.
 Doing file: /data/data22/seq_proc/33012010.005/ad33012010g300370m.unf
          Total      Good    Bad: Region      Time     Phase       Cut
           2867       714           1463       690         0         0
 Writing events file
    714 events written to the output file
===============================================================================
   Grand Total      Good   Bad:  Region      Time     Phase       Cut
          2867       714           1463       690         0         0
   in    1344.04 seconds
Infile # of rows    Outfile # of rows    # filtered
----------------    -----------------    ----------
         714                 623                91
 Command not found; type ? for a command listing
!screen:ASCA > set mission ASCA
 
 Notes: XSELECT set up for      ASCA
 Keywords for time and pha are  TIME       PI
 Units of time are              s
 Default timing binsize =    16.00
 Keywords for images are          DETX       DETY
 Keywords for the WMAP are        DETX       DETY
 
!screen:ASCA > set datadir .
 
Setting data directory to /data/data22/seq_proc/33012010.005/
Setting mkf directory to /data/data22/seq_proc/33012010.005/
 
!screen:ASCA > read events ad33012010g300370m.unf
Got new instrument: GIS3
 
Setting: IMAGE binning    =    1
         WMAP binning     =    1
         Energy Column    =  PI
         Energy rebinning =    1
 
 
Getting Min and Max for Energy Column...
Got min and max for PI:     0   1023
 
Got the minimum time resolution of the read data:  0.50000
 Number of files read in:   1
 
******************** Observation Catalogue ********************
 
Data Directory is: /data/data22/seq_proc/33012010.005/
HK Directory is: /data/data22/seq_proc/33012010.005/
 
!screen:ASCA-GIS3-PH > filter region GIS3_REGION256.4
!screen:ASCA-GIS3-PH > select mkf "@criteria.tmp" data_dir=. ASCA_mkf_def_expr=ft*.mkf
!screen:ASCA-GIS3-PH > extract events
!screen:ASCA-GIS3-PH > gisclean
Using table:/opt/local/ftools/ftools.4.0.c/SunOS_5.4_sparc/refdata/rti_gis_1024_040693.fits
!screen:ASCA-GIS3-PH > save clean outfile=ad33012010g300370m.evt use_events=no
!screen:ASCA-GIS3-PH > exit save_session=no
-> Setting NEVENTS to 623 in ad33012010g300370m.unf

Generating images and exposure maps ( 14:30:44 )

-> Generating exposure map ad33012010g200170h.expo
-> GIS2_REGION256.4 already present in current directory
-> Standard Output From STOOL regionmap:
-ANNULUS(128.5,128.5,192,88)
-ELLIPSE(167.5,220,24.66,28.95,245.298)
-> gis2_ano_on_flf_180295.fits already present in current directory
-> Running ascaexpo for ad33012010g200170h.evt
-> Standard Output From FTOOL ascaexpo:
ASCAEXPO_V0.9b
 
    reading data file: ad33012010g200170h.evt
    reading   gti ext: STDGTI
    reading  cal file: gis2_ano_on_flf_180295.fits
    reading inst file: GIS2_REGION256.4_regionmap.tmp
 
    making an inst map...
     multiply inst map...
 
    reading att  file: ./fa960129_1730.2300
 
    making an exposure map...
 
 Aspect RA/DEC/ROLL :       44.0009      19.3660     110.1816
 Mean   RA/DEC/ROLL :       44.0009      19.3896     110.1816
 Pnt    RA/DEC/ROLL :       44.0007      19.3428     110.1816
 
 Image rebin factor :             1
 Attitude Records   :         12906
 GTI intervals      :            10
 Total GTI (secs)   :      3814.005
 
 Max attitude excursion (arcsecs) :         5.000
 
   0 Percent Complete: Total/live time:        0.0000000       0.0000000
  10 Percent Complete: Total/live time:      872.9974365     872.9974365
  20 Percent Complete: Total/live time:      872.9974365     872.9974365
  30 Percent Complete: Total/live time:     2182.0053711    2182.0053711
  40 Percent Complete: Total/live time:     2182.0053711    2182.0053711
  50 Percent Complete: Total/live time:     3814.0053711    3814.0053711
  60 Percent Complete: Total/live time:     3814.0053711    3814.0053711
  70 Percent Complete: Total/live time:     3814.0053711    3814.0053711
 100 Percent Complete: Total/live time:     3814.0053711    3814.0053711
 
 Number of attitude steps  used:            5
 Number of attitude steps avail:        11629
 Mean RA/DEC pixel offset:      -10.4560      -2.2652
 
    writing expo file: ad33012010g200170h.expo
    closing attitude file...
    closing data file...
-> Generating low and high energy images for ad33012010g200170h.evt
-> Standard Output From FTOOL xselect:
 
                         **  XSELECT V1.3   **
 
!> Enter session name >[xsel] ad33012010g200170h
 
 Notes: XSELECT set up for      ASCA
 Keywords for time and pha are  TIME       PI
 Units of time are              s
 Default timing binsize =    16.00
 Keywords for images are          DETX       DETY
 Keywords for the WMAP are        DETX       DETY
 
 
 
        OBJECT   DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME   NEVENTS  PHA_BINS
      1 XY_ARI   PH       HIGH     29/01/96 17:43:01 0.38E+04     1358     1024
 
EXTRACTOR vers 2.0  11 Apr 1997.
 Getting FITS WCS Keywords
 Doing file: /data/data22/seq_proc/33012010.005/ad33012010g200170h.evt
          Total      Good    Bad: Region      Time     Phase       Cut
           1358      1340             18         0         0         0
===============================================================================
   Grand Total      Good   Bad:  Region      Time     Phase       Cut
          1358      1340             18         0         0         0
   in    3814.01 seconds
 Image            has     1340 counts for 0.3513     counts/sec
EXTRACTOR vers 2.0  11 Apr 1997.
 Getting FITS WCS Keywords
 Doing file: /data/data22/seq_proc/33012010.005/ad33012010g200170h.evt
          Total      Good    Bad: Region      Time     Phase       Cut
           1358       367             18         0         0       973
===============================================================================
   Grand Total      Good   Bad:  Region      Time     Phase       Cut
          1358       367             18         0         0       973
   in    3814.01 seconds
 Image            has      367 counts for 9.6224E-02 counts/sec
EXTRACTOR vers 2.0  11 Apr 1997.
 Getting FITS WCS Keywords
 Doing file: /data/data22/seq_proc/33012010.005/ad33012010g200170h.evt
          Total      Good    Bad: Region      Time     Phase       Cut
           1358       978             18         0         0       362
===============================================================================
   Grand Total      Good   Bad:  Region      Time     Phase       Cut
          1358       978             18         0         0       362
   in    3814.01 seconds
 Image            has      978 counts for 0.2564     counts/sec
 Command not found; type ? for a command listing
!ad33012010g200170h:ASCA >
!ad33012010g200170h:ASCA > set mission ASCA
 
 Notes: XSELECT set up for      ASCA
 Keywords for time and pha are  TIME       PI
 Units of time are              s
 Default timing binsize =    16.00
 Keywords for images are          DETX       DETY
 Keywords for the WMAP are        DETX       DETY
 
!ad33012010g200170h:ASCA > set datadir .
 
Setting data directory to /data/data22/seq_proc/33012010.005/
Setting mkf directory to /data/data22/seq_proc/33012010.005/
 
!ad33012010g200170h:ASCA > read events ad33012010g200170h.evt
Got new instrument: GIS2
 
Setting: IMAGE binning    =    1
         WMAP binning     =    1
         Energy Column    =  PI
         Energy rebinning =    1
 
 
Getting Min and Max for Energy Column...
Got min and max for PI:     0   1023
 
Got the minimum time resolution of the read data:  0.62500E-01
 Number of files read in:   1
 
******************** Observation Catalogue ********************
 
Data Directory is: /data/data22/seq_proc/33012010.005/
HK Directory is: /data/data22/seq_proc/33012010.005/
 
!ad33012010g200170h:ASCA-GIS2-PH > set image sky
!ad33012010g200170h:ASCA-GIS2-PH > filter region corner_point.reg
!ad33012010g200170h:ASCA-GIS2-PH > extract image
!ad33012010g200170h:ASCA-GIS2-PH > save image outfile=ad33012010g200170h.img
Wrote image to file ad33012010g200170h.img
!ad33012010g200170h:ASCA-GIS2-PH > filter pha_cut 0 170
!ad33012010g200170h:ASCA-GIS2-PH > extract image
!ad33012010g200170h:ASCA-GIS2-PH > save image outfile=ad33012010g200170h_lo.img
Wrote image to file ad33012010g200170h_lo.img
!ad33012010g200170h:ASCA-GIS2-PH > clear pha_cut
!ad33012010g200170h:ASCA-GIS2-PH > filter pha_cut 170 1024
Warning: your PI upper bound:  1024 is above the maximum value.
!ad33012010g200170h:ASCA-GIS2-PH > extract image
!ad33012010g200170h:ASCA-GIS2-PH > save image outfile=ad33012010g200170h_hi.img
Wrote image to file ad33012010g200170h_hi.img
!ad33012010g200170h:ASCA-GIS2-PH > exit save_session=no
-> Generating exposure map ad33012010g200270l.expo
-> GIS2_REGION256.4 already present in current directory
-> gis2_ano_on_flf_180295.fits already present in current directory
-> Running ascaexpo for ad33012010g200270l.evt
-> Standard Output From FTOOL ascaexpo:
ASCAEXPO_V0.9b
 
    reading data file: ad33012010g200270l.evt
    reading   gti ext: STDGTI
    reading  cal file: gis2_ano_on_flf_180295.fits
    reading inst file: GIS2_REGION256.4_regionmap.tmp
 
    making an inst map...
     multiply inst map...
 
    reading att  file: ./fa960129_1730.2300
 
    making an exposure map...
 
 Aspect RA/DEC/ROLL :       44.0009      19.3660     110.1811
 Mean   RA/DEC/ROLL :       44.0009      19.3897     110.1811
 Pnt    RA/DEC/ROLL :       44.0017      19.3435     110.1811
 
 Image rebin factor :             1
 Attitude Records   :         12906
 GTI intervals      :             1
 Total GTI (secs)   :        31.964
 
 Max attitude excursion (arcsecs) :         5.000
 
   0 Percent Complete: Total/live time:        0.0000000       0.0000000
  10 Percent Complete: Total/live time:       12.9636345      12.9636345
  20 Percent Complete: Total/live time:       31.9636745      31.9636745
 100 Percent Complete: Total/live time:       31.9636745      31.9636745
 
 Number of attitude steps  used:            2
 Number of attitude steps avail:           24
 Mean RA/DEC pixel offset:       -5.3666      -2.0097
 
    writing expo file: ad33012010g200270l.expo
    closing attitude file...
    closing data file...
-> Generating low and high energy images for ad33012010g200270l.evt
-> Standard Output From FTOOL xselect:
 
                         **  XSELECT V1.3   **
 
!> Enter session name >[xsel] ad33012010g200270l
 
 Notes: XSELECT set up for      ASCA
 Keywords for time and pha are  TIME       PI
 Units of time are              s
 Default timing binsize =    16.00
 Keywords for images are          DETX       DETY
 Keywords for the WMAP are        DETX       DETY
 
 
 
        OBJECT   DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME   NEVENTS  PHA_BINS
      1 XY_ARI   PH       LOW      29/01/96 18:46:29 0.32E+02       16     1024
 
EXTRACTOR vers 2.0  11 Apr 1997.
 Getting FITS WCS Keywords
 Doing file: /data/data22/seq_proc/33012010.005/ad33012010g200270l.evt
          Total      Good    Bad: Region      Time     Phase       Cut
             16        16              0         0         0         0
===============================================================================
   Grand Total      Good   Bad:  Region      Time     Phase       Cut
            16        16              0         0         0         0
   in      31.96 seconds
 Image            has       16 counts for 0.5006     counts/sec
EXTRACTOR vers 2.0  11 Apr 1997.
 Getting FITS WCS Keywords
 Doing file: /data/data22/seq_proc/33012010.005/ad33012010g200270l.evt
          Total      Good    Bad: Region      Time     Phase       Cut
             16         3              0         0         0        13
===============================================================================
   Grand Total      Good   Bad:  Region      Time     Phase       Cut
            16         3              0         0         0        13
   in      31.96 seconds
 Image            has        3 counts for 9.3857E-02 counts/sec
EXTRACTOR vers 2.0  11 Apr 1997.
 Getting FITS WCS Keywords
 Doing file: /data/data22/seq_proc/33012010.005/ad33012010g200270l.evt
          Total      Good    Bad: Region      Time     Phase       Cut
             16        13              0         0         0         3
===============================================================================
   Grand Total      Good   Bad:  Region      Time     Phase       Cut
            16        13              0         0         0         3
   in      31.96 seconds
 Image            has       13 counts for 0.4067     counts/sec
 Command not found; type ? for a command listing
!ad33012010g200270l:ASCA >
!ad33012010g200270l:ASCA > set mission ASCA
 
 Notes: XSELECT set up for      ASCA
 Keywords for time and pha are  TIME       PI
 Units of time are              s
 Default timing binsize =    16.00
 Keywords for images are          DETX       DETY
 Keywords for the WMAP are        DETX       DETY
 
!ad33012010g200270l:ASCA > set datadir .
 
Setting data directory to /data/data22/seq_proc/33012010.005/
Setting mkf directory to /data/data22/seq_proc/33012010.005/
 
!ad33012010g200270l:ASCA > read events ad33012010g200270l.evt
Got new instrument: GIS2
 
Setting: IMAGE binning    =    1
         WMAP binning     =    1
         Energy Column    =  PI
         Energy rebinning =    1
 
 
Getting Min and Max for Energy Column...
Got min and max for PI:     0   1023
 
Got the minimum time resolution of the read data:   2.0000
 Number of files read in:   1
 
******************** Observation Catalogue ********************
 
Data Directory is: /data/data22/seq_proc/33012010.005/
HK Directory is: /data/data22/seq_proc/33012010.005/
 
!ad33012010g200270l:ASCA-GIS2-PH > set image sky
!ad33012010g200270l:ASCA-GIS2-PH > filter region corner_point.reg
!ad33012010g200270l:ASCA-GIS2-PH > extract image
!ad33012010g200270l:ASCA-GIS2-PH > save image outfile=ad33012010g200270l.img
Wrote image to file ad33012010g200270l.img
!ad33012010g200270l:ASCA-GIS2-PH > filter pha_cut 0 170
!ad33012010g200270l:ASCA-GIS2-PH > extract image
!ad33012010g200270l:ASCA-GIS2-PH > save image outfile=ad33012010g200270l_lo.img
Wrote image to file ad33012010g200270l_lo.img
!ad33012010g200270l:ASCA-GIS2-PH > clear pha_cut
!ad33012010g200270l:ASCA-GIS2-PH > filter pha_cut 170 1024
Warning: your PI upper bound:  1024 is above the maximum value.
!ad33012010g200270l:ASCA-GIS2-PH > extract image
!ad33012010g200270l:ASCA-GIS2-PH > save image outfile=ad33012010g200270l_hi.img
Wrote image to file ad33012010g200270l_hi.img
!ad33012010g200270l:ASCA-GIS2-PH > exit save_session=no
-> Generating exposure map ad33012010g200370m.expo
-> GIS2_REGION256.4 already present in current directory
-> gis2_ano_on_flf_180295.fits already present in current directory
-> Running ascaexpo for ad33012010g200370m.evt
-> Standard Output From FTOOL ascaexpo:
ASCAEXPO_V0.9b
 
    reading data file: ad33012010g200370m.evt
    reading   gti ext: STDGTI
    reading  cal file: gis2_ano_on_flf_180295.fits
    reading inst file: GIS2_REGION256.4_regionmap.tmp
 
    making an inst map...
     multiply inst map...
 
    reading att  file: ./fa960129_1730.2300
 
    making an exposure map...
 
 Aspect RA/DEC/ROLL :       44.0009      19.3660     110.1814
 Mean   RA/DEC/ROLL :       44.0016      19.3894     110.1814
 Pnt    RA/DEC/ROLL :       44.0015      19.3427     110.1814
 
 Image rebin factor :             1
 Attitude Records   :         12906
 GTI intervals      :             4
 Total GTI (secs)   :      1344.042
 
 Max attitude excursion (arcsecs) :         5.000
 
   0 Percent Complete: Total/live time:        0.0000000       0.0000000
  10 Percent Complete: Total/live time:      832.0052490     832.0052490
  20 Percent Complete: Total/live time:      832.0052490     832.0052490
  30 Percent Complete: Total/live time:     1344.0417480    1344.0417480
 100 Percent Complete: Total/live time:     1344.0417480    1344.0417480
 
 Number of attitude steps  used:            3
 Number of attitude steps avail:         2369
 Mean RA/DEC pixel offset:       -7.2538      -2.8031
 
    writing expo file: ad33012010g200370m.expo
    closing attitude file...
    closing data file...
-> Generating low and high energy images for ad33012010g200370m.evt
-> Standard Output From FTOOL xselect:
 
                         **  XSELECT V1.3   **
 
!> Enter session name >[xsel] ad33012010g200370m
 
 Notes: XSELECT set up for      ASCA
 Keywords for time and pha are  TIME       PI
 Units of time are              s
 Default timing binsize =    16.00
 Keywords for images are          DETX       DETY
 Keywords for the WMAP are        DETX       DETY
 
 
 
        OBJECT   DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME   NEVENTS  PHA_BINS
      1 XY_ARI   PH       MEDIUM   29/01/96 17:30:29 0.13E+04      547     1024
 
EXTRACTOR vers 2.0  11 Apr 1997.
 Getting FITS WCS Keywords
 Doing file: /data/data22/seq_proc/33012010.005/ad33012010g200370m.evt
          Total      Good    Bad: Region      Time     Phase       Cut
            547       544              3         0         0         0
===============================================================================
   Grand Total      Good   Bad:  Region      Time     Phase       Cut
           547       544              3         0         0         0
   in    1344.04 seconds
 Image            has      544 counts for 0.4047     counts/sec
EXTRACTOR vers 2.0  11 Apr 1997.
 Getting FITS WCS Keywords
 Doing file: /data/data22/seq_proc/33012010.005/ad33012010g200370m.evt
          Total      Good    Bad: Region      Time     Phase       Cut
            547       157              3         0         0       387
===============================================================================
   Grand Total      Good   Bad:  Region      Time     Phase       Cut
           547       157              3         0         0       387
   in    1344.04 seconds
 Image            has      157 counts for 0.1168     counts/sec
EXTRACTOR vers 2.0  11 Apr 1997.
 Getting FITS WCS Keywords
 Doing file: /data/data22/seq_proc/33012010.005/ad33012010g200370m.evt
          Total      Good    Bad: Region      Time     Phase       Cut
            547       387              3         0         0       157
===============================================================================
   Grand Total      Good   Bad:  Region      Time     Phase       Cut
           547       387              3         0         0       157
   in    1344.04 seconds
 Image            has      387 counts for 0.2879     counts/sec
 Command not found; type ? for a command listing
!ad33012010g200370m:ASCA >
!ad33012010g200370m:ASCA > set mission ASCA
 
 Notes: XSELECT set up for      ASCA
 Keywords for time and pha are  TIME       PI
 Units of time are              s
 Default timing binsize =    16.00
 Keywords for images are          DETX       DETY
 Keywords for the WMAP are        DETX       DETY
 
!ad33012010g200370m:ASCA > set datadir .
 
Setting data directory to /data/data22/seq_proc/33012010.005/
Setting mkf directory to /data/data22/seq_proc/33012010.005/
 
!ad33012010g200370m:ASCA > read events ad33012010g200370m.evt
Got new instrument: GIS2
 
Setting: IMAGE binning    =    1
         WMAP binning     =    1
         Energy Column    =  PI
         Energy rebinning =    1
 
 
Getting Min and Max for Energy Column...
Got min and max for PI:     0   1023
 
Got the minimum time resolution of the read data:  0.50000
 Number of files read in:   1
 
******************** Observation Catalogue ********************
 
Data Directory is: /data/data22/seq_proc/33012010.005/
HK Directory is: /data/data22/seq_proc/33012010.005/
 
!ad33012010g200370m:ASCA-GIS2-PH > set image sky
!ad33012010g200370m:ASCA-GIS2-PH > filter region corner_point.reg
!ad33012010g200370m:ASCA-GIS2-PH > extract image
!ad33012010g200370m:ASCA-GIS2-PH > save image outfile=ad33012010g200370m.img
Wrote image to file ad33012010g200370m.img
!ad33012010g200370m:ASCA-GIS2-PH > filter pha_cut 0 170
!ad33012010g200370m:ASCA-GIS2-PH > extract image
!ad33012010g200370m:ASCA-GIS2-PH > save image outfile=ad33012010g200370m_lo.img
Wrote image to file ad33012010g200370m_lo.img
!ad33012010g200370m:ASCA-GIS2-PH > clear pha_cut
!ad33012010g200370m:ASCA-GIS2-PH > filter pha_cut 170 1024
Warning: your PI upper bound:  1024 is above the maximum value.
!ad33012010g200370m:ASCA-GIS2-PH > extract image
!ad33012010g200370m:ASCA-GIS2-PH > save image outfile=ad33012010g200370m_hi.img
Wrote image to file ad33012010g200370m_hi.img
!ad33012010g200370m:ASCA-GIS2-PH > exit save_session=no
-> Generating exposure map ad33012010g300170h.expo
-> GIS3_REGION256.4 already present in current directory
-> Standard Output From STOOL regionmap:
-ANNULUS(128.5,128.5,192,88)
-ELLIPSE(217,95,21.56,25.92,169.216)
-> gis3_ano_on_flf_180295.fits already present in current directory
-> Running ascaexpo for ad33012010g300170h.evt
-> Standard Output From FTOOL ascaexpo:
ASCAEXPO_V0.9b
 
    reading data file: ad33012010g300170h.evt
    reading   gti ext: STDGTI
    reading  cal file: gis3_ano_on_flf_180295.fits
    reading inst file: GIS3_REGION256.4_regionmap.tmp
 
    making an inst map...
     multiply inst map...
 
    reading att  file: ./fa960129_1730.2300
 
    making an exposure map...
 
 Aspect RA/DEC/ROLL :       44.0009      19.3660     110.1838
 Mean   RA/DEC/ROLL :       44.0075      19.3655     110.1838
 Pnt    RA/DEC/ROLL :       43.9941      19.3668     110.1838
 
 Image rebin factor :             1
 Attitude Records   :         12906
 GTI intervals      :            11
 Total GTI (secs)   :      3811.964
 
 Max attitude excursion (arcsecs) :         5.000
 
   0 Percent Complete: Total/live time:        0.0000000       0.0000000
  10 Percent Complete: Total/live time:      870.9974976     870.9974976
  20 Percent Complete: Total/live time:      870.9974976     870.9974976
  30 Percent Complete: Total/live time:     2179.9643555    2179.9643555
  40 Percent Complete: Total/live time:     2179.9643555    2179.9643555
  50 Percent Complete: Total/live time:     3811.9643555    3811.9643555
 100 Percent Complete: Total/live time:     3811.9643555    3811.9643555
 
 Number of attitude steps  used:            5
 Number of attitude steps avail:        11629
 Mean RA/DEC pixel offset:        1.0607      -1.9136
 
    writing expo file: ad33012010g300170h.expo
    closing attitude file...
    closing data file...
-> Generating low and high energy images for ad33012010g300170h.evt
-> Standard Output From FTOOL xselect:
 
                         **  XSELECT V1.3   **
 
!> Enter session name >[xsel] ad33012010g300170h
 
 Notes: XSELECT set up for      ASCA
 Keywords for time and pha are  TIME       PI
 Units of time are              s
 Default timing binsize =    16.00
 Keywords for images are          DETX       DETY
 Keywords for the WMAP are        DETX       DETY
 
 
 
        OBJECT   DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME   NEVENTS  PHA_BINS
      1 XY_ARI   PH       HIGH     29/01/96 17:43:01 0.38E+04     1552     1024
 
EXTRACTOR vers 2.0  11 Apr 1997.
 Getting FITS WCS Keywords
 Doing file: /data/data22/seq_proc/33012010.005/ad33012010g300170h.evt
          Total      Good    Bad: Region      Time     Phase       Cut
           1552      1539             13         0         0         0
===============================================================================
   Grand Total      Good   Bad:  Region      Time     Phase       Cut
          1552      1539             13         0         0         0
   in    3811.96 seconds
 Image            has     1539 counts for 0.4037     counts/sec
EXTRACTOR vers 2.0  11 Apr 1997.
 Getting FITS WCS Keywords
 Doing file: /data/data22/seq_proc/33012010.005/ad33012010g300170h.evt
          Total      Good    Bad: Region      Time     Phase       Cut
           1552       424             13         0         0      1115
===============================================================================
   Grand Total      Good   Bad:  Region      Time     Phase       Cut
          1552       424             13         0         0      1115
   in    3811.96 seconds
 Image            has      424 counts for 0.1112     counts/sec
EXTRACTOR vers 2.0  11 Apr 1997.
 Getting FITS WCS Keywords
 Doing file: /data/data22/seq_proc/33012010.005/ad33012010g300170h.evt
          Total      Good    Bad: Region      Time     Phase       Cut
           1552      1117             13         0         0       422
===============================================================================
   Grand Total      Good   Bad:  Region      Time     Phase       Cut
          1552      1117             13         0         0       422
   in    3811.96 seconds
 Image            has     1117 counts for 0.2930     counts/sec
 Command not found; type ? for a command listing
!ad33012010g300170h:ASCA >
!ad33012010g300170h:ASCA > set mission ASCA
 
 Notes: XSELECT set up for      ASCA
 Keywords for time and pha are  TIME       PI
 Units of time are              s
 Default timing binsize =    16.00
 Keywords for images are          DETX       DETY
 Keywords for the WMAP are        DETX       DETY
 
!ad33012010g300170h:ASCA > set datadir .
 
Setting data directory to /data/data22/seq_proc/33012010.005/
Setting mkf directory to /data/data22/seq_proc/33012010.005/
 
!ad33012010g300170h:ASCA > read events ad33012010g300170h.evt
Got new instrument: GIS3
 
Setting: IMAGE binning    =    1
         WMAP binning     =    1
         Energy Column    =  PI
         Energy rebinning =    1
 
 
Getting Min and Max for Energy Column...
Got min and max for PI:     0   1023
 
Got the minimum time resolution of the read data:  0.62500E-01
 Number of files read in:   1
 
******************** Observation Catalogue ********************
 
Data Directory is: /data/data22/seq_proc/33012010.005/
HK Directory is: /data/data22/seq_proc/33012010.005/
 
!ad33012010g300170h:ASCA-GIS3-PH > set image sky
!ad33012010g300170h:ASCA-GIS3-PH > filter region corner_point.reg
!ad33012010g300170h:ASCA-GIS3-PH > extract image
!ad33012010g300170h:ASCA-GIS3-PH > save image outfile=ad33012010g300170h.img
Wrote image to file ad33012010g300170h.img
!ad33012010g300170h:ASCA-GIS3-PH > filter pha_cut 0 170
!ad33012010g300170h:ASCA-GIS3-PH > extract image
!ad33012010g300170h:ASCA-GIS3-PH > save image outfile=ad33012010g300170h_lo.img
Wrote image to file ad33012010g300170h_lo.img
!ad33012010g300170h:ASCA-GIS3-PH > clear pha_cut
!ad33012010g300170h:ASCA-GIS3-PH > filter pha_cut 170 1024
Warning: your PI upper bound:  1024 is above the maximum value.
!ad33012010g300170h:ASCA-GIS3-PH > extract image
!ad33012010g300170h:ASCA-GIS3-PH > save image outfile=ad33012010g300170h_hi.img
Wrote image to file ad33012010g300170h_hi.img
!ad33012010g300170h:ASCA-GIS3-PH > exit save_session=no
-> Generating exposure map ad33012010g300270l.expo
-> GIS3_REGION256.4 already present in current directory
-> gis3_ano_on_flf_180295.fits already present in current directory
-> Running ascaexpo for ad33012010g300270l.evt
-> Standard Output From FTOOL ascaexpo:
ASCAEXPO_V0.9b
 
    reading data file: ad33012010g300270l.evt
    reading   gti ext: STDGTI
    reading  cal file: gis3_ano_on_flf_180295.fits
    reading inst file: GIS3_REGION256.4_regionmap.tmp
 
    making an inst map...
     multiply inst map...
 
    reading att  file: ./fa960129_1730.2300
 
    making an exposure map...
 
 Aspect RA/DEC/ROLL :       44.0009      19.3660     110.1833
 Mean   RA/DEC/ROLL :       44.0075      19.3656     110.1833
 Pnt    RA/DEC/ROLL :       43.9951      19.3675     110.1833
 
 Image rebin factor :             1
 Attitude Records   :         12906
 GTI intervals      :             1
 Total GTI (secs)   :        31.964
 
 Max attitude excursion (arcsecs) :         5.000
 
   0 Percent Complete: Total/live time:        0.0000000       0.0000000
  10 Percent Complete: Total/live time:       12.9636345      12.9636345
  20 Percent Complete: Total/live time:       31.9636745      31.9636745
 100 Percent Complete: Total/live time:       31.9636745      31.9636745
 
 Number of attitude steps  used:            2
 Number of attitude steps avail:           24
 Mean RA/DEC pixel offset:        0.6728      -1.4097
 
    writing expo file: ad33012010g300270l.expo
    closing attitude file...
    closing data file...
-> Generating low and high energy images for ad33012010g300270l.evt
-> Standard Output From FTOOL xselect:
 
                         **  XSELECT V1.3   **
 
!> Enter session name >[xsel] ad33012010g300270l
 
 Notes: XSELECT set up for      ASCA
 Keywords for time and pha are  TIME       PI
 Units of time are              s
 Default timing binsize =    16.00
 Keywords for images are          DETX       DETY
 Keywords for the WMAP are        DETX       DETY
 
 
 
        OBJECT   DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME   NEVENTS  PHA_BINS
      1 XY_ARI   PH       LOW      29/01/96 18:46:29 0.32E+02       18     1024
 
EXTRACTOR vers 2.0  11 Apr 1997.
 Getting FITS WCS Keywords
 Doing file: /data/data22/seq_proc/33012010.005/ad33012010g300270l.evt
          Total      Good    Bad: Region      Time     Phase       Cut
             18        17              1         0         0         0
===============================================================================
   Grand Total      Good   Bad:  Region      Time     Phase       Cut
            18        17              1         0         0         0
   in      31.96 seconds
 Image            has       17 counts for 0.5319     counts/sec
EXTRACTOR vers 2.0  11 Apr 1997.
 Getting FITS WCS Keywords
 Doing file: /data/data22/seq_proc/33012010.005/ad33012010g300270l.evt
          Total      Good    Bad: Region      Time     Phase       Cut
             18         3              1         0         0        14
===============================================================================
   Grand Total      Good   Bad:  Region      Time     Phase       Cut
            18         3              1         0         0        14
   in      31.96 seconds
 Image            has        3 counts for 9.3857E-02 counts/sec
EXTRACTOR vers 2.0  11 Apr 1997.
 Getting FITS WCS Keywords
 Doing file: /data/data22/seq_proc/33012010.005/ad33012010g300270l.evt
          Total      Good    Bad: Region      Time     Phase       Cut
             18        14              1         0         0         3
===============================================================================
   Grand Total      Good   Bad:  Region      Time     Phase       Cut
            18        14              1         0         0         3
   in      31.96 seconds
 Image            has       14 counts for 0.4380     counts/sec
 Command not found; type ? for a command listing
!ad33012010g300270l:ASCA >
!ad33012010g300270l:ASCA > set mission ASCA
 
 Notes: XSELECT set up for      ASCA
 Keywords for time and pha are  TIME       PI
 Units of time are              s
 Default timing binsize =    16.00
 Keywords for images are          DETX       DETY
 Keywords for the WMAP are        DETX       DETY
 
!ad33012010g300270l:ASCA > set datadir .
 
Setting data directory to /data/data22/seq_proc/33012010.005/
Setting mkf directory to /data/data22/seq_proc/33012010.005/
 
!ad33012010g300270l:ASCA > read events ad33012010g300270l.evt
Got new instrument: GIS3
 
Setting: IMAGE binning    =    1
         WMAP binning     =    1
         Energy Column    =  PI
         Energy rebinning =    1
 
 
Getting Min and Max for Energy Column...
Got min and max for PI:     0   1023
 
Got the minimum time resolution of the read data:   2.0000
 Number of files read in:   1
 
******************** Observation Catalogue ********************
 
Data Directory is: /data/data22/seq_proc/33012010.005/
HK Directory is: /data/data22/seq_proc/33012010.005/
 
!ad33012010g300270l:ASCA-GIS3-PH > set image sky
!ad33012010g300270l:ASCA-GIS3-PH > filter region corner_point.reg
!ad33012010g300270l:ASCA-GIS3-PH > extract image
!ad33012010g300270l:ASCA-GIS3-PH > save image outfile=ad33012010g300270l.img
Wrote image to file ad33012010g300270l.img
!ad33012010g300270l:ASCA-GIS3-PH > filter pha_cut 0 170
!ad33012010g300270l:ASCA-GIS3-PH > extract image
!ad33012010g300270l:ASCA-GIS3-PH > save image outfile=ad33012010g300270l_lo.img
Wrote image to file ad33012010g300270l_lo.img
!ad33012010g300270l:ASCA-GIS3-PH > clear pha_cut
!ad33012010g300270l:ASCA-GIS3-PH > filter pha_cut 170 1024
Warning: your PI upper bound:  1024 is above the maximum value.
!ad33012010g300270l:ASCA-GIS3-PH > extract image
!ad33012010g300270l:ASCA-GIS3-PH > save image outfile=ad33012010g300270l_hi.img
Wrote image to file ad33012010g300270l_hi.img
!ad33012010g300270l:ASCA-GIS3-PH > exit save_session=no
-> Generating exposure map ad33012010g300370m.expo
-> GIS3_REGION256.4 already present in current directory
-> gis3_ano_on_flf_180295.fits already present in current directory
-> Running ascaexpo for ad33012010g300370m.evt
-> Standard Output From FTOOL ascaexpo:
ASCAEXPO_V0.9b
 
    reading data file: ad33012010g300370m.evt
    reading   gti ext: STDGTI
    reading  cal file: gis3_ano_on_flf_180295.fits
    reading inst file: GIS3_REGION256.4_regionmap.tmp
 
    making an inst map...
     multiply inst map...
 
    reading att  file: ./fa960129_1730.2300
 
    making an exposure map...
 
 Aspect RA/DEC/ROLL :       44.0009      19.3660     110.1836
 Mean   RA/DEC/ROLL :       44.0082      19.3654     110.1836
 Pnt    RA/DEC/ROLL :       43.9949      19.3668     110.1836
 
 Image rebin factor :             1
 Attitude Records   :         12906
 GTI intervals      :             4
 Total GTI (secs)   :      1344.042
 
 Max attitude excursion (arcsecs) :         5.000
 
   0 Percent Complete: Total/live time:        0.0000000       0.0000000
  10 Percent Complete: Total/live time:      832.0052490     832.0052490
  20 Percent Complete: Total/live time:      832.0052490     832.0052490
  30 Percent Complete: Total/live time:     1344.0417480    1344.0417480
 100 Percent Complete: Total/live time:     1344.0417480    1344.0417480
 
 Number of attitude steps  used:            3
 Number of attitude steps avail:         2369
 Mean RA/DEC pixel offset:        0.7987      -2.0031
 
    writing expo file: ad33012010g300370m.expo
    closing attitude file...
    closing data file...
-> Generating low and high energy images for ad33012010g300370m.evt
-> Standard Output From FTOOL xselect:
 
                         **  XSELECT V1.3   **
 
!> Enter session name >[xsel] ad33012010g300370m
 
 Notes: XSELECT set up for      ASCA
 Keywords for time and pha are  TIME       PI
 Units of time are              s
 Default timing binsize =    16.00
 Keywords for images are          DETX       DETY
 Keywords for the WMAP are        DETX       DETY
 
 
 
        OBJECT   DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME   NEVENTS  PHA_BINS
      1 XY_ARI   PH       MEDIUM   29/01/96 17:30:29 0.13E+04      623     1024
 
EXTRACTOR vers 2.0  11 Apr 1997.
 Getting FITS WCS Keywords
 Doing file: /data/data22/seq_proc/33012010.005/ad33012010g300370m.evt
          Total      Good    Bad: Region      Time     Phase       Cut
            623       619              4         0         0         0
===============================================================================
   Grand Total      Good   Bad:  Region      Time     Phase       Cut
           623       619              4         0         0         0
   in    1344.04 seconds
 Image            has      619 counts for 0.4606     counts/sec
EXTRACTOR vers 2.0  11 Apr 1997.
 Getting FITS WCS Keywords
 Doing file: /data/data22/seq_proc/33012010.005/ad33012010g300370m.evt
          Total      Good    Bad: Region      Time     Phase       Cut
            623       158              4         0         0       461
===============================================================================
   Grand Total      Good   Bad:  Region      Time     Phase       Cut
           623       158              4         0         0       461
   in    1344.04 seconds
 Image            has      158 counts for 0.1176     counts/sec
EXTRACTOR vers 2.0  11 Apr 1997.
 Getting FITS WCS Keywords
 Doing file: /data/data22/seq_proc/33012010.005/ad33012010g300370m.evt
          Total      Good    Bad: Region      Time     Phase       Cut
            623       462              4         0         0       157
===============================================================================
   Grand Total      Good   Bad:  Region      Time     Phase       Cut
           623       462              4         0         0       157
   in    1344.04 seconds
 Image            has      462 counts for 0.3437     counts/sec
 Command not found; type ? for a command listing
!ad33012010g300370m:ASCA >
!ad33012010g300370m:ASCA > set mission ASCA
 
 Notes: XSELECT set up for      ASCA
 Keywords for time and pha are  TIME       PI
 Units of time are              s
 Default timing binsize =    16.00
 Keywords for images are          DETX       DETY
 Keywords for the WMAP are        DETX       DETY
 
!ad33012010g300370m:ASCA > set datadir .
 
Setting data directory to /data/data22/seq_proc/33012010.005/
Setting mkf directory to /data/data22/seq_proc/33012010.005/
 
!ad33012010g300370m:ASCA > read events ad33012010g300370m.evt
Got new instrument: GIS3
 
Setting: IMAGE binning    =    1
         WMAP binning     =    1
         Energy Column    =  PI
         Energy rebinning =    1
 
 
Getting Min and Max for Energy Column...
Got min and max for PI:     0   1023
 
Got the minimum time resolution of the read data:  0.50000
 Number of files read in:   1
 
******************** Observation Catalogue ********************
 
Data Directory is: /data/data22/seq_proc/33012010.005/
HK Directory is: /data/data22/seq_proc/33012010.005/
 
!ad33012010g300370m:ASCA-GIS3-PH > set image sky
!ad33012010g300370m:ASCA-GIS3-PH > filter region corner_point.reg
!ad33012010g300370m:ASCA-GIS3-PH > extract image
!ad33012010g300370m:ASCA-GIS3-PH > save image outfile=ad33012010g300370m.img
Wrote image to file ad33012010g300370m.img
!ad33012010g300370m:ASCA-GIS3-PH > filter pha_cut 0 170
!ad33012010g300370m:ASCA-GIS3-PH > extract image
!ad33012010g300370m:ASCA-GIS3-PH > save image outfile=ad33012010g300370m_lo.img
Wrote image to file ad33012010g300370m_lo.img
!ad33012010g300370m:ASCA-GIS3-PH > clear pha_cut
!ad33012010g300370m:ASCA-GIS3-PH > filter pha_cut 170 1024
Warning: your PI upper bound:  1024 is above the maximum value.
!ad33012010g300370m:ASCA-GIS3-PH > extract image
!ad33012010g300370m:ASCA-GIS3-PH > save image outfile=ad33012010g300370m_hi.img
Wrote image to file ad33012010g300370m_hi.img
!ad33012010g300370m:ASCA-GIS3-PH > exit save_session=no
-> Generating exposure map ad33012010s000102h.expo
-> s0_teldef_ascalin.fits already present in current directory
-> Running ascaexpo for ad33012010s000102h.evt
-> Standard Output From FTOOL ascaexpo:
ASCAEXPO_V0.9b
 
    reading data file: ad33012010s000102h.evt
    reading   gti ext: STDGTI
    reading    hp ext: HOT_PIXELS
    reading  cal file: s0_teldef_ascalin.fits
 
    making an inst map...
  
 SIS AREA DISC ENABL         OFF
  
              CHIP:            0           1           2           3
  
 CCD POWER  ON/OFF:          OFF          ON         OFF         OFF
 AREA DISC  IN/OUT:          OUT         OUT          IN          IN
 AREA DISC H START:            6           6           6         316
 AREA DISC H  STOP:          425         425         200         425
 AREA DISC V START:            2           2           2           2
 AREA DISC V  STOP:          422         422         150         112
  
    reading att  file: ./fa960129_1730.2300
 
    making an exposure map...
 
 Aspect RA/DEC/ROLL :       44.0009      19.3660     110.1878
 Mean   RA/DEC/ROLL :       44.0195      19.3828     110.1878
 Pnt    RA/DEC/ROLL :       43.9822      19.3497     110.1878
 
 Image rebin factor :             4
 Attitude Records   :         12906
 Hot Pixels         :             5
 GTI intervals      :            11
 Total GTI (secs)   :      3895.917
 
 Max attitude excursion (arcsecs) :         5.000
 
   0 Percent Complete: Total/live time:        0.0000000       0.0000000
  10 Percent Complete: Total/live time:     1325.8826904    1325.8826904
  20 Percent Complete: Total/live time:     1325.8826904    1325.8826904
  30 Percent Complete: Total/live time:     1682.8815918    1682.8815918
  40 Percent Complete: Total/live time:     1682.8815918    1682.8815918
  50 Percent Complete: Total/live time:     2519.9165039    2519.9165039
  60 Percent Complete: Total/live time:     2519.9165039    2519.9165039
  70 Percent Complete: Total/live time:     3895.9165039    3895.9165039
 100 Percent Complete: Total/live time:     3895.9165039    3895.9165039
 
 Number of attitude steps  used:            6
 Number of attitude steps avail:        10752
 Mean RA/DEC pixel offset:      -35.8905     -82.4725
 
    writing expo file: ad33012010s000102h.expo
    closing attitude file...
    closing data file...
-> Generating low and high energy images for ad33012010s000102h.evt
-> Standard Output From FTOOL xselect:
 
                         **  XSELECT V1.3   **
 
!> Enter session name >[xsel] ad33012010s000102h
 
 Notes: XSELECT set up for      ASCA
 Keywords for time and pha are  TIME       PI
 Units of time are              s
 Default timing binsize =    16.00
 Keywords for images are          DETX       DETY
 Keywords for the WMAP are        DETX       DETY
 
 
 
        OBJECT   DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME   NEVENTS  S0CCDPOW
      1 XY_ARI   BRIGHT   HIGH     29/01/96 17:42:55 0.39E+04      661 0100
 
EXTRACTOR vers 2.0  11 Apr 1997.
 Getting FITS WCS Keywords
 Doing file: /data/data22/seq_proc/33012010.005/ad33012010s000102h.evt
          Total      Good    Bad: Region      Time     Phase       Cut
            661       661              0         0         0         0
===============================================================================
   Grand Total      Good   Bad:  Region      Time     Phase       Cut
           661       661              0         0         0         0
   in    3895.92 seconds
 Image            has      661 counts for 0.1697     counts/sec
EXTRACTOR vers 2.0  11 Apr 1997.
 Getting FITS WCS Keywords
 Doing file: /data/data22/seq_proc/33012010.005/ad33012010s000102h.evt
          Total      Good    Bad: Region      Time     Phase       Cut
            661        77              0         0         0       584
===============================================================================
   Grand Total      Good   Bad:  Region      Time     Phase       Cut
           661        77              0         0         0       584
   in    3895.92 seconds
 Image            has       77 counts for 1.9764E-02 counts/sec
EXTRACTOR vers 2.0  11 Apr 1997.
 Getting FITS WCS Keywords
 Doing file: /data/data22/seq_proc/33012010.005/ad33012010s000102h.evt
          Total      Good    Bad: Region      Time     Phase       Cut
            661       584              0         0         0        77
===============================================================================
   Grand Total      Good   Bad:  Region      Time     Phase       Cut
           661       584              0         0         0        77
   in    3895.92 seconds
 Image            has      584 counts for 0.1499     counts/sec
 Command not found; type ? for a command listing
!ad33012010s000102h:ASCA >
!ad33012010s000102h:ASCA > set mission ASCA
 
 Notes: XSELECT set up for      ASCA
 Keywords for time and pha are  TIME       PI
 Units of time are              s
 Default timing binsize =    16.00
 Keywords for images are          DETX       DETY
 Keywords for the WMAP are        DETX       DETY
 
!ad33012010s000102h:ASCA > set datadir .
 
Setting data directory to /data/data22/seq_proc/33012010.005/
Setting mkf directory to /data/data22/seq_proc/33012010.005/
 
!ad33012010s000102h:ASCA > read events ad33012010s000102h.evt
Got new instrument: SIS0
 
Setting: IMAGE binning    =    4
         WMAP binning     =    8
         Energy Column    =  PI
         Energy rebinning =    1
 
 
Getting Min and Max for Energy Column...
Got min and max for PI:     0   2047
 
Got the minimum time resolution of the read data:   4.0000
 Number of files read in:   1
 
******************** Observation Catalogue ********************
 
Data Directory is: /data/data22/seq_proc/33012010.005/
HK Directory is: /data/data22/seq_proc/33012010.005/
 
!ad33012010s000102h:ASCA-SIS0-BRIGHT > set image sky
!ad33012010s000102h:ASCA-SIS0-BRIGHT > filter region corner_point.reg
!ad33012010s000102h:ASCA-SIS0-BRIGHT > extract image
!ad33012010s000102h:ASCA-SIS0-BRIGHT > save image outfile=ad33012010s000102h.img
Wrote image to file ad33012010s000102h.img
!ad33012010s000102h:ASCA-SIS0-BRIGHT > filter pha_cut 0 547
!ad33012010s000102h:ASCA-SIS0-BRIGHT > extract image
!ad33012010s000102h:ASCA-SIS0-BRIGHT > save image outfile=ad33012010s000102h_lo.img
Wrote image to file ad33012010s000102h_lo.img
!ad33012010s000102h:ASCA-SIS0-BRIGHT > clear pha_cut
!ad33012010s000102h:ASCA-SIS0-BRIGHT > filter pha_cut 547 2048
Warning: your PI upper bound:  2048 is above the maximum value.
!ad33012010s000102h:ASCA-SIS0-BRIGHT > extract image
!ad33012010s000102h:ASCA-SIS0-BRIGHT > save image outfile=ad33012010s000102h_hi.img
Wrote image to file ad33012010s000102h_hi.img
!ad33012010s000102h:ASCA-SIS0-BRIGHT > exit save_session=no
-> Generating exposure map ad33012010s000302m.expo
-> s0_teldef_ascalin.fits already present in current directory
-> Running ascaexpo for ad33012010s000302m.evt
-> Standard Output From FTOOL ascaexpo:
ASCAEXPO_V0.9b
 
    reading data file: ad33012010s000302m.evt
    reading   gti ext: STDGTI
    reading    hp ext: HOT_PIXELS
    reading  cal file: s0_teldef_ascalin.fits
 
    making an inst map...
  
 SIS AREA DISC ENABL         OFF
  
              CHIP:            0           1           2           3
  
 CCD POWER  ON/OFF:          OFF          ON         OFF         OFF
 AREA DISC  IN/OUT:          OUT         OUT          IN          IN
 AREA DISC H START:            6           6           6         316
 AREA DISC H  STOP:          425         425         200         425
 AREA DISC V START:            2           2           2           2
 AREA DISC V  STOP:          422         422         150         112
  
    reading att  file: ./fa960129_1730.2300
 
    making an exposure map...
 
 Aspect RA/DEC/ROLL :       44.0009      19.3660     110.1876
 Mean   RA/DEC/ROLL :       44.0201      19.3827     110.1876
 Pnt    RA/DEC/ROLL :       43.9830      19.3496     110.1876
 
 Image rebin factor :             4
 Attitude Records   :         12906
 Hot Pixels         :             2
 GTI intervals      :             5
 Total GTI (secs)   :       695.726
 
 Max attitude excursion (arcsecs) :         5.000
 
   0 Percent Complete: Total/live time:        0.0000000       0.0000000
  10 Percent Complete: Total/live time:      407.7256470     407.7256470
  20 Percent Complete: Total/live time:      407.7256470     407.7256470
  30 Percent Complete: Total/live time:      695.7256470     695.7256470
 100 Percent Complete: Total/live time:      695.7256470     695.7256470
 
 Number of attitude steps  used:            3
 Number of attitude steps avail:         1635
 Mean RA/DEC pixel offset:      -29.4820     -69.4945
 
    writing expo file: ad33012010s000302m.expo
    closing attitude file...
    closing data file...
-> Generating low and high energy images for ad33012010s000302m.evt
-> Standard Output From FTOOL xselect:
 
                         **  XSELECT V1.3   **
 
!> Enter session name >[xsel] ad33012010s000302m
 
 Notes: XSELECT set up for      ASCA
 Keywords for time and pha are  TIME       PI
 Units of time are              s
 Default timing binsize =    16.00
 Keywords for images are          DETX       DETY
 Keywords for the WMAP are        DETX       DETY
 
 
 
        OBJECT   DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME   NEVENTS  S0CCDPOW
      1 XY_ARI   BRIGHT   MEDIUM   29/01/96 17:30:23 0.70E+03      151 0100
 
EXTRACTOR vers 2.0  11 Apr 1997.
 Getting FITS WCS Keywords
 Doing file: /data/data22/seq_proc/33012010.005/ad33012010s000302m.evt
          Total      Good    Bad: Region      Time     Phase       Cut
            151       151              0         0         0         0
===============================================================================
   Grand Total      Good   Bad:  Region      Time     Phase       Cut
           151       151              0         0         0         0
   in     695.73 seconds
 Image            has      151 counts for 0.2170     counts/sec
EXTRACTOR vers 2.0  11 Apr 1997.
 Getting FITS WCS Keywords
 Doing file: /data/data22/seq_proc/33012010.005/ad33012010s000302m.evt
          Total      Good    Bad: Region      Time     Phase       Cut
            151        16              0         0         0       135
===============================================================================
   Grand Total      Good   Bad:  Region      Time     Phase       Cut
           151        16              0         0         0       135
   in     695.73 seconds
 Image            has       16 counts for 2.2998E-02 counts/sec
EXTRACTOR vers 2.0  11 Apr 1997.
 Getting FITS WCS Keywords
 Doing file: /data/data22/seq_proc/33012010.005/ad33012010s000302m.evt
          Total      Good    Bad: Region      Time     Phase       Cut
            151       136              0         0         0        15
===============================================================================
   Grand Total      Good   Bad:  Region      Time     Phase       Cut
           151       136              0         0         0        15
   in     695.73 seconds
 Image            has      136 counts for 0.1955     counts/sec
 Command not found; type ? for a command listing
!ad33012010s000302m:ASCA >
!ad33012010s000302m:ASCA > set mission ASCA
 
 Notes: XSELECT set up for      ASCA
 Keywords for time and pha are  TIME       PI
 Units of time are              s
 Default timing binsize =    16.00
 Keywords for images are          DETX       DETY
 Keywords for the WMAP are        DETX       DETY
 
!ad33012010s000302m:ASCA > set datadir .
 
Setting data directory to /data/data22/seq_proc/33012010.005/
Setting mkf directory to /data/data22/seq_proc/33012010.005/
 
!ad33012010s000302m:ASCA > read events ad33012010s000302m.evt
Got new instrument: SIS0
 
Setting: IMAGE binning    =    4
         WMAP binning     =    8
         Energy Column    =  PI
         Energy rebinning =    1
 
 
Getting Min and Max for Energy Column...
Got min and max for PI:     0   2047
 
Got the minimum time resolution of the read data:   4.0000
 Number of files read in:   1
 
******************** Observation Catalogue ********************
 
Data Directory is: /data/data22/seq_proc/33012010.005/
HK Directory is: /data/data22/seq_proc/33012010.005/
 
!ad33012010s000302m:ASCA-SIS0-BRIGHT > set image sky
!ad33012010s000302m:ASCA-SIS0-BRIGHT > filter region corner_point.reg
!ad33012010s000302m:ASCA-SIS0-BRIGHT > extract image
!ad33012010s000302m:ASCA-SIS0-BRIGHT > save image outfile=ad33012010s000302m.img
Wrote image to file ad33012010s000302m.img
!ad33012010s000302m:ASCA-SIS0-BRIGHT > filter pha_cut 0 547
!ad33012010s000302m:ASCA-SIS0-BRIGHT > extract image
!ad33012010s000302m:ASCA-SIS0-BRIGHT > save image outfile=ad33012010s000302m_lo.img
Wrote image to file ad33012010s000302m_lo.img
!ad33012010s000302m:ASCA-SIS0-BRIGHT > clear pha_cut
!ad33012010s000302m:ASCA-SIS0-BRIGHT > filter pha_cut 547 2048
Warning: your PI upper bound:  2048 is above the maximum value.
!ad33012010s000302m:ASCA-SIS0-BRIGHT > extract image
!ad33012010s000302m:ASCA-SIS0-BRIGHT > save image outfile=ad33012010s000302m_hi.img
Wrote image to file ad33012010s000302m_hi.img
!ad33012010s000302m:ASCA-SIS0-BRIGHT > exit save_session=no
-> Generating exposure map ad33012010s100102h.expo
-> s1_teldef_ascalin.fits already present in current directory
-> Running ascaexpo for ad33012010s100102h.evt
-> Standard Output From FTOOL ascaexpo:
ASCAEXPO_V0.9b
 
    reading data file: ad33012010s100102h.evt
    reading   gti ext: STDGTI
    reading    hp ext: HOT_PIXELS
    reading  cal file: s1_teldef_ascalin.fits
 
    making an inst map...
  
 SIS AREA DISC ENABL         OFF
  
              CHIP:            0           1           2           3
  
 CCD POWER  ON/OFF:          OFF         OFF         OFF          ON
 AREA DISC  IN/OUT:          OUT         OUT         OUT         OUT
 AREA DISC H START:            6           6           6           6
 AREA DISC H  STOP:          425         425         425         425
 AREA DISC V START:            2           2           2           2
 AREA DISC V  STOP:          422         422         422         422
  
    reading att  file: ./fa960129_1730.2300
 
    making an exposure map...
 
 Aspect RA/DEC/ROLL :       44.0009      19.3660     110.1824
 Mean   RA/DEC/ROLL :       44.0033      19.3782     110.1824
 Pnt    RA/DEC/ROLL :       43.9984      19.3543     110.1824
 
 Image rebin factor :             4
 Attitude Records   :         12906
 Hot Pixels         :            10
 GTI intervals      :            11
 Total GTI (secs)   :      3937.885
 
 Max attitude excursion (arcsecs) :         5.000
 
   0 Percent Complete: Total/live time:        0.0000000       0.0000000
  10 Percent Complete: Total/live time:     1339.8514404    1339.8514404
  20 Percent Complete: Total/live time:     1339.8514404    1339.8514404
  30 Percent Complete: Total/live time:     1696.8503418    1696.8503418
  40 Percent Complete: Total/live time:     1696.8503418    1696.8503418
  50 Percent Complete: Total/live time:     2529.8854980    2529.8854980
  60 Percent Complete: Total/live time:     2529.8854980    2529.8854980
  70 Percent Complete: Total/live time:     3937.8852539    3937.8852539
 100 Percent Complete: Total/live time:     3937.8852539    3937.8852539
 
 Number of attitude steps  used:            6
 Number of attitude steps avail:        10754
 Mean RA/DEC pixel offset:      -39.5973     -22.6218
 
    writing expo file: ad33012010s100102h.expo
    closing attitude file...
    closing data file...
-> Generating low and high energy images for ad33012010s100102h.evt
-> Standard Output From FTOOL xselect:
 
                         **  XSELECT V1.3   **
 
!> Enter session name >[xsel] ad33012010s100102h
 
 Notes: XSELECT set up for      ASCA
 Keywords for time and pha are  TIME       PI
 Units of time are              s
 Default timing binsize =    16.00
 Keywords for images are          DETX       DETY
 Keywords for the WMAP are        DETX       DETY
 
 
 
        OBJECT   DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME   NEVENTS  S1CCDPOW
      1 XY_ARI   BRIGHT   HIGH     29/01/96 17:42:55 0.39E+04      628 0001
 
EXTRACTOR vers 2.0  11 Apr 1997.
 Getting FITS WCS Keywords
 Doing file: /data/data22/seq_proc/33012010.005/ad33012010s100102h.evt
          Total      Good    Bad: Region      Time     Phase       Cut
            628       628              0         0         0         0
===============================================================================
   Grand Total      Good   Bad:  Region      Time     Phase       Cut
           628       628              0         0         0         0
   in    3937.89 seconds
 Image            has      628 counts for 0.1595     counts/sec
EXTRACTOR vers 2.0  11 Apr 1997.
 Getting FITS WCS Keywords
 Doing file: /data/data22/seq_proc/33012010.005/ad33012010s100102h.evt
          Total      Good    Bad: Region      Time     Phase       Cut
            628        76              0         0         0       552
===============================================================================
   Grand Total      Good   Bad:  Region      Time     Phase       Cut
           628        76              0         0         0       552
   in    3937.89 seconds
 Image            has       76 counts for 1.9300E-02 counts/sec
EXTRACTOR vers 2.0  11 Apr 1997.
 Getting FITS WCS Keywords
 Doing file: /data/data22/seq_proc/33012010.005/ad33012010s100102h.evt
          Total      Good    Bad: Region      Time     Phase       Cut
            628       553              0         0         0        75
===============================================================================
   Grand Total      Good   Bad:  Region      Time     Phase       Cut
           628       553              0         0         0        75
   in    3937.89 seconds
 Image            has      553 counts for 0.1404     counts/sec
 Command not found; type ? for a command listing
!ad33012010s100102h:ASCA >
!ad33012010s100102h:ASCA > set mission ASCA
 
 Notes: XSELECT set up for      ASCA
 Keywords for time and pha are  TIME       PI
 Units of time are              s
 Default timing binsize =    16.00
 Keywords for images are          DETX       DETY
 Keywords for the WMAP are        DETX       DETY
 
!ad33012010s100102h:ASCA > set datadir .
 
Setting data directory to /data/data22/seq_proc/33012010.005/
Setting mkf directory to /data/data22/seq_proc/33012010.005/
 
!ad33012010s100102h:ASCA > read events ad33012010s100102h.evt
Got new instrument: SIS1
 
Setting: IMAGE binning    =    4
         WMAP binning     =    8
         Energy Column    =  PI
         Energy rebinning =    1
 
 
Getting Min and Max for Energy Column...
Got min and max for PI:     0   2047
 
Got the minimum time resolution of the read data:   4.0000
 Number of files read in:   1
 
******************** Observation Catalogue ********************
 
Data Directory is: /data/data22/seq_proc/33012010.005/
HK Directory is: /data/data22/seq_proc/33012010.005/
 
!ad33012010s100102h:ASCA-SIS1-BRIGHT > set image sky
!ad33012010s100102h:ASCA-SIS1-BRIGHT > filter region corner_point.reg
!ad33012010s100102h:ASCA-SIS1-BRIGHT > extract image
!ad33012010s100102h:ASCA-SIS1-BRIGHT > save image outfile=ad33012010s100102h.img
Wrote image to file ad33012010s100102h.img
!ad33012010s100102h:ASCA-SIS1-BRIGHT > filter pha_cut 0 547
!ad33012010s100102h:ASCA-SIS1-BRIGHT > extract image
!ad33012010s100102h:ASCA-SIS1-BRIGHT > save image outfile=ad33012010s100102h_lo.img
Wrote image to file ad33012010s100102h_lo.img
!ad33012010s100102h:ASCA-SIS1-BRIGHT > clear pha_cut
!ad33012010s100102h:ASCA-SIS1-BRIGHT > filter pha_cut 547 2048
Warning: your PI upper bound:  2048 is above the maximum value.
!ad33012010s100102h:ASCA-SIS1-BRIGHT > extract image
!ad33012010s100102h:ASCA-SIS1-BRIGHT > save image outfile=ad33012010s100102h_hi.img
Wrote image to file ad33012010s100102h_hi.img
!ad33012010s100102h:ASCA-SIS1-BRIGHT > exit save_session=no
-> Generating exposure map ad33012010s100302m.expo
-> s1_teldef_ascalin.fits already present in current directory
-> Running ascaexpo for ad33012010s100302m.evt
-> Standard Output From FTOOL ascaexpo:
ASCAEXPO_V0.9b
 
    reading data file: ad33012010s100302m.evt
    reading   gti ext: STDGTI
    reading    hp ext: HOT_PIXELS
    reading  cal file: s1_teldef_ascalin.fits
 
    making an inst map...
  
 SIS AREA DISC ENABL         OFF
  
              CHIP:            0           1           2           3
  
 CCD POWER  ON/OFF:          OFF         OFF         OFF          ON
 AREA DISC  IN/OUT:          OUT         OUT         OUT         OUT
 AREA DISC H START:            6           6           6           6
 AREA DISC H  STOP:          425         425         425         425
 AREA DISC V START:            2           2           2           2
 AREA DISC V  STOP:          422         422         422         422
  
    reading att  file: ./fa960129_1730.2300
 
    making an exposure map...
 
 Aspect RA/DEC/ROLL :       44.0009      19.3660     110.1822
 Mean   RA/DEC/ROLL :       44.0040      19.3780     110.1822
 Pnt    RA/DEC/ROLL :       43.9991      19.3541     110.1822
 
 Image rebin factor :             4
 Attitude Records   :         12906
 Hot Pixels         :             8
 GTI intervals      :             3
 Total GTI (secs)   :       791.726
 
 Max attitude excursion (arcsecs) :         5.000
 
   0 Percent Complete: Total/live time:        0.0000000       0.0000000
  10 Percent Complete: Total/live time:      503.7256470     503.7256470
  20 Percent Complete: Total/live time:      503.7256470     503.7256470
  30 Percent Complete: Total/live time:      791.7256470     791.7256470
 100 Percent Complete: Total/live time:      791.7256470     791.7256470
 
 Number of attitude steps  used:            3
 Number of attitude steps avail:         1635
 Mean RA/DEC pixel offset:      -32.4449     -21.5937
 
    writing expo file: ad33012010s100302m.expo
    closing attitude file...
    closing data file...
-> Generating low and high energy images for ad33012010s100302m.evt
-> Standard Output From FTOOL xselect:
 
                         **  XSELECT V1.3   **
 
!> Enter session name >[xsel] ad33012010s100302m
 
 Notes: XSELECT set up for      ASCA
 Keywords for time and pha are  TIME       PI
 Units of time are              s
 Default timing binsize =    16.00
 Keywords for images are          DETX       DETY
 Keywords for the WMAP are        DETX       DETY
 
 
 
        OBJECT   DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME   NEVENTS  S1CCDPOW
      1 XY_ARI   BRIGHT   MEDIUM   29/01/96 17:30:23 0.79E+03      153 0001
 
EXTRACTOR vers 2.0  11 Apr 1997.
 Getting FITS WCS Keywords
 Doing file: /data/data22/seq_proc/33012010.005/ad33012010s100302m.evt
          Total      Good    Bad: Region      Time     Phase       Cut
            153       153              0         0         0         0
===============================================================================
   Grand Total      Good   Bad:  Region      Time     Phase       Cut
           153       153              0         0         0         0
   in     791.73 seconds
 Image            has      153 counts for 0.1932     counts/sec
EXTRACTOR vers 2.0  11 Apr 1997.
 Getting FITS WCS Keywords
 Doing file: /data/data22/seq_proc/33012010.005/ad33012010s100302m.evt
          Total      Good    Bad: Region      Time     Phase       Cut
            153        26              0         0         0       127
===============================================================================
   Grand Total      Good   Bad:  Region      Time     Phase       Cut
           153        26              0         0         0       127
   in     791.73 seconds
 Image            has       26 counts for 3.2840E-02 counts/sec
EXTRACTOR vers 2.0  11 Apr 1997.
 Getting FITS WCS Keywords
 Doing file: /data/data22/seq_proc/33012010.005/ad33012010s100302m.evt
          Total      Good    Bad: Region      Time     Phase       Cut
            153       127              0         0         0        26
===============================================================================
   Grand Total      Good   Bad:  Region      Time     Phase       Cut
           153       127              0         0         0        26
   in     791.73 seconds
 Image            has      127 counts for 0.1604     counts/sec
 Command not found; type ? for a command listing
!ad33012010s100302m:ASCA >
!ad33012010s100302m:ASCA > set mission ASCA
 
 Notes: XSELECT set up for      ASCA
 Keywords for time and pha are  TIME       PI
 Units of time are              s
 Default timing binsize =    16.00
 Keywords for images are          DETX       DETY
 Keywords for the WMAP are        DETX       DETY
 
!ad33012010s100302m:ASCA > set datadir .
 
Setting data directory to /data/data22/seq_proc/33012010.005/
Setting mkf directory to /data/data22/seq_proc/33012010.005/
 
!ad33012010s100302m:ASCA > read events ad33012010s100302m.evt
Got new instrument: SIS1
 
Setting: IMAGE binning    =    4
         WMAP binning     =    8
         Energy Column    =  PI
         Energy rebinning =    1
 
 
Getting Min and Max for Energy Column...
Got min and max for PI:     0   2047
 
Got the minimum time resolution of the read data:   4.0000
 Number of files read in:   1
 
******************** Observation Catalogue ********************
 
Data Directory is: /data/data22/seq_proc/33012010.005/
HK Directory is: /data/data22/seq_proc/33012010.005/
 
!ad33012010s100302m:ASCA-SIS1-BRIGHT > set image sky
!ad33012010s100302m:ASCA-SIS1-BRIGHT > filter region corner_point.reg
!ad33012010s100302m:ASCA-SIS1-BRIGHT > extract image
!ad33012010s100302m:ASCA-SIS1-BRIGHT > save image outfile=ad33012010s100302m.img
Wrote image to file ad33012010s100302m.img
!ad33012010s100302m:ASCA-SIS1-BRIGHT > filter pha_cut 0 547
!ad33012010s100302m:ASCA-SIS1-BRIGHT > extract image
!ad33012010s100302m:ASCA-SIS1-BRIGHT > save image outfile=ad33012010s100302m_lo.img
Wrote image to file ad33012010s100302m_lo.img
!ad33012010s100302m:ASCA-SIS1-BRIGHT > clear pha_cut
!ad33012010s100302m:ASCA-SIS1-BRIGHT > filter pha_cut 547 2048
Warning: your PI upper bound:  2048 is above the maximum value.
!ad33012010s100302m:ASCA-SIS1-BRIGHT > extract image
!ad33012010s100302m:ASCA-SIS1-BRIGHT > save image outfile=ad33012010s100302m_hi.img
Wrote image to file ad33012010s100302m_hi.img
!ad33012010s100302m:ASCA-SIS1-BRIGHT > exit save_session=no
-> Summing sis images
-> Summing the following images to produce ad33012010sis32002.totexpo
ad33012010s000102h.expo
ad33012010s000302m.expo
ad33012010s100102h.expo
ad33012010s100302m.expo
-> Summing the following images to produce ad33012010sis32002_all.totsky
ad33012010s000102h.img
ad33012010s000302m.img
ad33012010s100102h.img
ad33012010s100302m.img
-> Summing the following images to produce ad33012010sis32002_lo.totsky
ad33012010s000102h_lo.img
ad33012010s000302m_lo.img
ad33012010s100102h_lo.img
ad33012010s100302m_lo.img
-> Summing the following images to produce ad33012010sis32002_hi.totsky
ad33012010s000102h_hi.img
ad33012010s000302m_hi.img
ad33012010s100102h_hi.img
ad33012010s100302m_hi.img
-> Running XIMAGE to create ad33012010sis32002.gif
-> Standard Output From STOOL ximage:
 No of detectors read in:   20
![1]XIMAGE> read/fits ad33012010sis32002_all.totsky
 Reading an image
 Telescope ASCA SIS0
  Image display size =  320
 Done, closing file
  Largest, Smallest    14.0000  0.
  Bscale, Bzero from file     1.0000000000000  0.
After internal scaling
  Bscale and Bzero    1.0000000000000  0.
 Image level, max:  14 min:  0
![2]XIMAGE> read/exp_map ad33012010sis32002.totexpo
 Reading an image
 Telescope ASCA SIS0
  Image display size =  320
 Done, closing file
  Largest, Smallest    155.354  0.
  Bscale, Bzero from file     1.0000000000000  0.
After internal scaling
  Bscale and Bzero    1.0000000000000  0.
 Image level, max:  155 min:  0
![3]XIMAGE> smooth
![4]XIMAGE> cpd /ppm
![5]XIMAGE> cey 2000
![6]XIMAGE> disp/correct/noframe
 Displaying image
 The image is exposure corrected
  Min =  0 max =   15
![7]XIMAGE> grid
![8]XIMAGE> scale
 scal_f, min_inten    1.00000  0.
 i,inten,mm,pp  1  0.  0  0
 i,inten,mm,pp  2    4.00000  40  -1
 i,inten,mm,pp  3    8.00000  80  -1
 i,inten,mm,pp  4    12.0000  12  0
![9]XIMAGE> exit
-> Summing gis images
-> Summing the following images to produce ad33012010gis25670.totexpo
ad33012010g200170h.expo
ad33012010g200270l.expo
ad33012010g200370m.expo
ad33012010g300170h.expo
ad33012010g300270l.expo
ad33012010g300370m.expo
-> Summing the following images to produce ad33012010gis25670_all.totsky
ad33012010g200170h.img
ad33012010g200270l.img
ad33012010g200370m.img
ad33012010g300170h.img
ad33012010g300270l.img
ad33012010g300370m.img
-> Summing the following images to produce ad33012010gis25670_lo.totsky
ad33012010g200170h_lo.img
ad33012010g200270l_lo.img
ad33012010g200370m_lo.img
ad33012010g300170h_lo.img
ad33012010g300270l_lo.img
ad33012010g300370m_lo.img
-> Summing the following images to produce ad33012010gis25670_hi.totsky
ad33012010g200170h_hi.img
ad33012010g200270l_hi.img
ad33012010g200370m_hi.img
ad33012010g300170h_hi.img
ad33012010g300270l_hi.img
ad33012010g300370m_hi.img
-> Running XIMAGE to create ad33012010gis25670.gif
-> Standard Output From STOOL ximage:
 No of detectors read in:   20
![1]XIMAGE> read/fits ad33012010gis25670_all.totsky
 Reading an image
 Telescope ASCA GIS2
  Image display size =  256
 Done, closing file
  Largest, Smallest    17.0000  0.
  Bscale, Bzero from file     1.0000000000000  0.
After internal scaling
  Bscale and Bzero    1.0000000000000  0.
 Image level, max:  17 min:  0
![2]XIMAGE> read/exp_map ad33012010gis25670.totexpo
 Reading an image
 Telescope ASCA GIS2
  Image display size =  256
 Done, closing file
  Largest, Smallest    172.966  0.
  Bscale, Bzero from file     1.0000000000000  0.
After internal scaling
  Bscale and Bzero    1.0000000000000  0.
 Image level, max:  172 min:  0
![3]XIMAGE> smooth
![4]XIMAGE> cpd /ppm
![5]XIMAGE> cey 2000
![6]XIMAGE> disp/correct/noframe
 Displaying image
 The image is exposure corrected
  Min =  0 max =   27
![7]XIMAGE> grid
![8]XIMAGE> scale
 scal_f, min_inten    1.00000  0.
 i,inten,mm,pp  1  0.  0  0
 i,inten,mm,pp  2    4.00000  40  -1
 i,inten,mm,pp  3    8.00000  80  -1
 i,inten,mm,pp  4    16.0000  16  0
![9]XIMAGE> exit

Detecting sources in summed images ( 14:48:32 )

-> Smoothing ad33012010gis25670_all.totsky with ad33012010gis25670.totexpo
-> Clipping exposures below 1556.6970858 seconds
-> Detecting sources in ad33012010gis25670_all.smooth
-> Standard Output From STOOL ascasource:
123 147 0.00110276 111 7 103.151
-> Smoothing ad33012010gis25670_hi.totsky with ad33012010gis25670.totexpo
-> Clipping exposures below 1556.6970858 seconds
-> Detecting sources in ad33012010gis25670_hi.smooth
-> Standard Output From STOOL ascasource:
123 147 0.00104923 111 7 172.251
-> Smoothing ad33012010gis25670_lo.totsky with ad33012010gis25670.totexpo
-> Clipping exposures below 1556.6970858 seconds
-> Detecting sources in ad33012010gis25670_lo.smooth
-> Determining extraction radii
-> Eliminating redundant sources
-> Standard Output From STOOL sift_sources:
123 147 24 F
-> Standard Output From STOOL colorpic:
color plane 0
color plane 1
color plane 2
writing image
image written
-> Creating fits catalog of sources: ad33012010gis25670.src
-> Smoothing ad33012010sis32002_all.totsky with ad33012010sis32002.totexpo
-> Clipping exposures below 1398.1879944 seconds
-> Detecting sources in ad33012010sis32002_all.smooth
-> Standard Output From STOOL ascasource:
147 203 0.000390844 100 10 108.652
-> Smoothing ad33012010sis32002_hi.totsky with ad33012010sis32002.totexpo
-> Clipping exposures below 1398.1879944 seconds
-> Detecting sources in ad33012010sis32002_hi.smooth
-> Standard Output From STOOL ascasource:
147 203 0.000377959 100 10 134.074
-> Smoothing ad33012010sis32002_lo.totsky with ad33012010sis32002.totexpo
-> Clipping exposures below 1398.1879944 seconds
-> Detecting sources in ad33012010sis32002_lo.smooth
-> Standard Output From STOOL ascasource:
146 199 6.6338e-06 103 37 5.67643
-> Determining extraction radii
-> Eliminating redundant sources
-> Standard Output From STOOL sift_sources:
147 203 38 F
-> Standard Output From STOOL colorpic:
color plane 0
color plane 1
color plane 2
writing image
image written
-> Creating fits catalog of sources: ad33012010sis32002.src
-> Generating region files
-> Converting (588.0,812.0,2.0) to s0 detector coordinates
-> Using events in: ad33012010s000102h.evt ad33012010s000302m.evt
-> Standard Output From FTOOL fstatistic:
 The sum of the selected column is                   952.00000
 The mean of the selected column is                  476.00000
 The standard deviation of the selected column is    1.4142136
 The minimum of selected column is                   475.00000
 The maximum of selected column is                   477.00000
 The number of points used in calculation is                2
-> Standard Output From FTOOL fstatistic:
 The sum of the selected column is                   966.00000
 The mean of the selected column is                  483.00000
 The standard deviation of the selected column is           0.
 The minimum of selected column is                   483.00000
 The maximum of selected column is                   483.00000
 The number of points used in calculation is                2
-> Converting (588.0,812.0,2.0) to s1 detector coordinates
-> Using events in: ad33012010s100102h.evt ad33012010s100302m.evt
-> Standard Output From FTOOL fstatistic:
 The sum of the selected column is                   1424.0000
 The mean of the selected column is                  474.66667
 The standard deviation of the selected column is    1.1547005
 The minimum of selected column is                   474.00000
 The maximum of selected column is                   476.00000
 The number of points used in calculation is                3
-> Standard Output From FTOOL fstatistic:
 The sum of the selected column is                   1558.0000
 The mean of the selected column is                  519.33333
 The standard deviation of the selected column is    1.1547005
 The minimum of selected column is                   518.00000
 The maximum of selected column is                   520.00000
 The number of points used in calculation is                3
-> Converting (123.0,147.0,2.0) to g2 detector coordinates
-> Using events in: ad33012010g200170h.evt ad33012010g200270l.evt ad33012010g200370m.evt
-> Standard Output From FTOOL fstatistic:
 The sum of the selected column is                   7390.0000
 The mean of the selected column is                  108.67647
 The standard deviation of the selected column is    1.0712132
 The minimum of selected column is                   106.00000
 The maximum of selected column is                   111.00000
 The number of points used in calculation is               68
-> Standard Output From FTOOL fstatistic:
 The sum of the selected column is                   7844.0000
 The mean of the selected column is                  115.35294
 The standard deviation of the selected column is   0.98896457
 The minimum of selected column is                   113.00000
 The maximum of selected column is                   117.00000
 The number of points used in calculation is               68
-> Converting (123.0,147.0,2.0) to g3 detector coordinates
-> Using events in: ad33012010g300170h.evt ad33012010g300270l.evt ad33012010g300370m.evt
-> Standard Output From FTOOL fstatistic:
 The sum of the selected column is                   9185.0000
 The mean of the selected column is                  114.81250
 The standard deviation of the selected column is    1.1261422
 The minimum of selected column is                   112.00000
 The maximum of selected column is                   117.00000
 The number of points used in calculation is               80
-> Standard Output From FTOOL fstatistic:
 The sum of the selected column is                   9233.0000
 The mean of the selected column is                  115.41250
 The standard deviation of the selected column is   0.88150834
 The minimum of selected column is                   113.00000
 The maximum of selected column is                   117.00000
 The number of points used in calculation is               80

Extracting spectra and generating response matrices ( 14:56:59 )

-> Fetching xrt_ea_v2_0.fits
-> Fetching xrt_psf_v2_0.fits
-> sisph2pi_110397.fits already present in current directory
-> Fetching sisechos_290296.fits
-> Fetching sisrddis_290296.fits
-> Standard Output From STOOL group_event_files:
1 ad33012010s000102h.evt 812
1 ad33012010s000302m.evt 812
-> Fetching SIS0_NOTCHIP0.1
-> Fetching SIS0_NOTCHIP2.1
-> Fetching SIS0_NOTCHIP3.1
-> Fetching SIS0_OFFCHIP.1
-> Extracting ad33012010s010102_1.pi from ad33012010s032002_1.reg and:
ad33012010s000102h.evt
ad33012010s000302m.evt
-> Standard Output From FTOOL xselect:
 
                         **  XSELECT V1.3   **
 
!> Enter session name >[xsel] xsel
 
 Notes: XSELECT set up for      ASCA
 Keywords for time and pha are  TIME       PI
 Units of time are              s
 Default timing binsize =    16.00
 Keywords for images are          DETX       DETY
 Keywords for the WMAP are        DETX       DETY
 
 
 
        OBJECT   DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME   NEVENTS  S0CCDPOW
      1 XY_ARI   BRIGHT   HIGH     29/01/96 17:42:55 0.39E+04      661 0100
 
 
 
        OBJECT   DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME   NEVENTS  S0CCDPOW
      1 XY_ARI   BRIGHT   HIGH     29/01/96 17:42:55 0.39E+04      661 0100
      2 XY_ARI   BRIGHT   MEDIUM   29/01/96 17:30:23 0.70E+03      151 0100
 
EXTRACTOR vers 2.0  11 Apr 1997.
 Getting FITS WCS Keywords
 Doing file: /data/data22/seq_proc/33012010.005/ad33012010s000102h.evt
          Total      Good    Bad: Region      Time     Phase       Cut
            661       518            143         0         0         0
 Doing file: /data/data22/seq_proc/33012010.005/ad33012010s000302m.evt
          Total      Good    Bad: Region      Time     Phase       Cut
            151       116             35         0         0         0
===============================================================================
   Grand Total      Good   Bad:  Region      Time     Phase       Cut
           812       634            178         0         0         0
   in    4591.64 seconds
 Spectrum         has      634 counts for 0.1381     counts/sec
 
  -------------------------
  MANDATORY KEYWORDS/VALUES
  -------------------------
  --------------------------------------------------------------------
  --------------------------------------------------------------------
  EXTNAME   - SPECTRUM        Name of this BINTABLE
  TELESCOP  - ASCA            Mission/Satellite name
  INSTRUME  - SIS0            Instrument/Detector
  FILTER    -                 Instrument filter in use
  EXPOSURE  - 4591.6          Integration time (in secs) of PHA data
  AREASCAL  - 1.0000          Area scaling factor
  BACKSCAL  - 4.45898E-02     Background scaling factor
  BACKFILE  - NONE            Associated background file
  CORRSCAL  - 1.0000          Correlation scaling factor
  CORRFILE  - none            Associated correlation file
  RESPFILE  - NONE            Associated redistribution matrix file
  ANCRFILE  - none            Associated ancillary response file
  XFLT0001  - none            XSPEC selection filter
  POISSERR  - TRUE            Whether Poissonian errors apply
  CHANTYPE  - PI              Whether channels have been corrected
  TLMIN1    - 0               First legal Detector channel
  DETCHANS  - 512             No. of legal detector channels
  NCHAN     - 512             No. of detector channels in dataset
  PHAVERSN  - 1.1.0           OGIP FITS version number
  STAT_ERR  - FALSE           Statistical Error
  SYS_ERR   - TRUE            Fractional Systematic Error
  QUALITY   - TRUE            Quality Flag
  GROUPING  - FALSE           Grouping Flag
  --------------------------------------------------------------------
  --------------------------------------------------------------------
 ...  QUALITY
 ...
 ...  -------
 ...  QUALITY
 ...  -------
 ...  Bad Channels (Channel - Channel)
 ...  ---------------------------------------------
 ...         0 -      15  have quality 5
 ...  ---------------------------------------------
 ...
 ...... exiting, changes written to file : ad33012010s010102_1.pi
 Command not found; type ? for a command listing
!xsel:ASCA > set mission ASCA
 
 Notes: XSELECT set up for      ASCA
 Keywords for time and pha are  TIME       PI
 Units of time are              s
 Default timing binsize =    16.00
 Keywords for images are          DETX       DETY
 Keywords for the WMAP are        DETX       DETY
 
!xsel:ASCA > set datadir .
 
Setting data directory to /data/data22/seq_proc/33012010.005/
Setting mkf directory to /data/data22/seq_proc/33012010.005/
 
!xsel:ASCA > read events ad33012010s000102h.evt
Got new instrument: SIS0
 
Setting: IMAGE binning    =    4
         WMAP binning     =    8
         Energy Column    =  PI
         Energy rebinning =    1
 
 
Getting Min and Max for Energy Column...
Got min and max for PI:     0   2047
 
Got the minimum time resolution of the read data:   4.0000
 Number of files read in:   1
 
******************** Observation Catalogue ********************
 
Data Directory is: /data/data22/seq_proc/33012010.005/
HK Directory is: /data/data22/seq_proc/33012010.005/
 
!xsel:ASCA-SIS0-BRIGHT > read events ad33012010s000302m.evt
 
Getting Min and Max for Energy Column...
Got min and max for PI:     0   2047
 
Got the minimum time resolution of the read data:   4.0000
 Number of files read in:   2
 
******************** Observation Catalogue ********************
 
Data Directory is: /data/data22/seq_proc/33012010.005/
HK Directory is: /data/data22/seq_proc/33012010.005/
 
!xsel:ASCA-SIS0-BRIGHT > set phaname PI
!xsel:ASCA-SIS0-BRIGHT > filter region ad33012010s032002_1.reg
!xsel:ASCA-SIS0-BRIGHT > filter region SIS0_NOTCHIP0.1
!xsel:ASCA-SIS0-BRIGHT > filter region SIS0_NOTCHIP2.1
!xsel:ASCA-SIS0-BRIGHT > filter region SIS0_NOTCHIP3.1
!xsel:ASCA-SIS0-BRIGHT > filter region SIS0_OFFCHIP.1
!xsel:ASCA-SIS0-BRIGHT > filter region ad33012010s010102.discrim
!xsel:ASCA-SIS0-BRIGHT > extract spectrum
!xsel:ASCA-SIS0-BRIGHT > save spectrum ad33012010s010102_1.pi group=yes
Wrote spectrum to ad33012010s010102_1.pi
!xsel:ASCA-SIS0-BRIGHT > exit save_session=no
-> Grouping ad33012010s010102_1.pi to 40 counts/bin
-> Standard Output From FTOOL grppha:
 
  -------------------------
  MANDATORY KEYWORDS/VALUES
  -------------------------
  --------------------------------------------------------------------
  --------------------------------------------------------------------
  EXTNAME   - SPECTRUM        Name of this BINTABLE
  TELESCOP  - ASCA            Mission/Satellite name
  INSTRUME  - SIS0            Instrument/Detector
  FILTER    -                 Instrument filter in use
  EXPOSURE  - 4591.6          Integration time (in secs) of PHA data
  AREASCAL  - 1.0000          Area scaling factor
  BACKSCAL  - 4.45898E-02     Background scaling factor
  BACKFILE  - NONE            Associated background file
  CORRSCAL  - 1.0000          Correlation scaling factor
  CORRFILE  - none            Associated correlation file
  RESPFILE  - NONE            Associated redistribution matrix file
  ANCRFILE  - none            Associated ancillary response file
  XFLT0001  - none            XSPEC selection filter
  POISSERR  - TRUE            Whether Poissonian errors apply
  CHANTYPE  - PI              Whether channels have been corrected
  TLMIN1    - 0               First legal Detector channel
  DETCHANS  - 512             No. of legal detector channels
  NCHAN     - 512             No. of detector channels in dataset
  PHAVERSN  - 1.1.0           OGIP FITS version number
  STAT_ERR  - FALSE           Statistical Error
  SYS_ERR   - TRUE            Fractional Systematic Error
  QUALITY   - TRUE            Quality Flag
  GROUPING  - FALSE           Grouping Flag
  --------------------------------------------------------------------
  --------------------------------------------------------------------
 ...
 ...  --------
 ...  GROUPING
 ...  --------
 ...  ---------------------------------------------
 ...  Channel Grouping (Channel-Channel) :
 ...         0 -      15  of undefined grouping (Channel quality=bad)
 ...        16 -      66  are grouped by a factor       51
 ...        67 -      87  are grouped by a factor       21
 ...        88 -      99  are grouped by a factor       12
 ...       100 -     121  are grouped by a factor       11
 ...       122 -     133  are grouped by a factor       12
 ...       134 -     142  are grouped by a factor        9
 ...       143 -     154  are grouped by a factor       12
 ...       155 -     165  are grouped by a factor       11
 ...       166 -     174  are grouped by a factor        9
 ...       175 -     188  are grouped by a factor       14
 ...       189 -     205  are grouped by a factor       17
 ...       206 -     232  are grouped by a factor       27
 ...  ---------------------------------------------
 ...
 ...... exiting, changes written to file : ad33012010s010102_1.pi
 ** grppha 2.6.0 completed successfully
-> Source occupies chip(s) 1
-> Fetching sis0c1p40_290296.fits
-> Generating ad33012010s010102_1.rmf
-> Standard Output From FTOOL sisrmg:
Sisrmg Version 1.1, Configured 04/97

  This version resolves *all* known keyword incompatibilities with
  other FTOOLS tasks.  If you have previously fudged *any* keywords
  in the PHA file to compensate, incorrect results will follow.
 
Setting 1st PHA channel to 0
Making v1.1 1180x512 S0C1 Bright PI RMF
Calibration data from ./
Please stand by...
...Done.
-> Generating ad33012010s010102_1.arf with point=yes
-> Standard Output From FTOOL ascaarf:
ASCAARF vers 2.72  14 Mar 1997.
 
 Input WMAP array has size   39 by   37 bins
               expanded to   39 by   37 bins
 First WMAP bin is at detector pixel  328  336
   8 detector pixels per WMAP bin
 WMAP bin size is   0.21600 mm
                    0.21216 arcmin
 Selected region size is   51.381     arcmin^2
 Optical axis is detector pixel 662.72 559.02
 
 1180 energies from RMF file
 Effective area fudge applied
 Arf filter applied
 
 Point source at  487.00  487.00 (detector coordinates)
 Point source at   21.97    9.00 (WMAP bins wrt optical axis)
 Point source at    5.04   22.29 (... in polar coordinates)
 
 Total counts in region = 6.25000E+02
 Weighted mean angle from optical axis  =  5.232 arcmin
 
-> Standard Output From STOOL group_event_files:
1 ad33012010s000112h.evt 863
1 ad33012010s000312m.evt 863
-> SIS0_NOTCHIP0.1 already present in current directory
-> SIS0_NOTCHIP2.1 already present in current directory
-> SIS0_NOTCHIP3.1 already present in current directory
-> SIS0_OFFCHIP.1 already present in current directory
-> Extracting ad33012010s010212_1.pi from ad33012010s032002_1.reg and:
ad33012010s000112h.evt
ad33012010s000312m.evt
-> Standard Output From FTOOL xselect:
 
                         **  XSELECT V1.3   **
 
!> Enter session name >[xsel] xsel
 
 Notes: XSELECT set up for      ASCA
 Keywords for time and pha are  TIME       PI
 Units of time are              s
 Default timing binsize =    16.00
 Keywords for images are          DETX       DETY
 Keywords for the WMAP are        DETX       DETY
 
 
 
        OBJECT   DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME   NEVENTS  S0CCDPOW
      1 XY_ARI   BRIGHT2  HIGH     29/01/96 17:42:55 0.39E+04      701 0100
 
 
 
        OBJECT   DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME   NEVENTS  S0CCDPOW
      1 XY_ARI   BRIGHT2  HIGH     29/01/96 17:42:55 0.39E+04      701 0100
      2 XY_ARI   BRIGHT2  MEDIUM   29/01/96 17:30:23 0.70E+03      162 0100
 
EXTRACTOR vers 2.0  11 Apr 1997.
 Getting FITS WCS Keywords
 Doing file: /data/data22/seq_proc/33012010.005/ad33012010s000112h.evt
          Total      Good    Bad: Region      Time     Phase       Cut
            701       540            161         0         0         0
 Doing file: /data/data22/seq_proc/33012010.005/ad33012010s000312m.evt
          Total      Good    Bad: Region      Time     Phase       Cut
            162       124             38         0         0         0
===============================================================================
   Grand Total      Good   Bad:  Region      Time     Phase       Cut
           863       664            199         0         0         0
   in    4591.64 seconds
 Spectrum         has      664 counts for 0.1446     counts/sec
 
  -------------------------
  MANDATORY KEYWORDS/VALUES
  -------------------------
  --------------------------------------------------------------------
  --------------------------------------------------------------------
  EXTNAME   - SPECTRUM        Name of this BINTABLE
  TELESCOP  - ASCA            Mission/Satellite name
  INSTRUME  - SIS0            Instrument/Detector
  FILTER    -                 Instrument filter in use
  EXPOSURE  - 4591.6          Integration time (in secs) of PHA data
  AREASCAL  - 1.0000          Area scaling factor
  BACKSCAL  - 4.45898E-02     Background scaling factor
  BACKFILE  - NONE            Associated background file
  CORRSCAL  - 1.0000          Correlation scaling factor
  CORRFILE  - none            Associated correlation file
  RESPFILE  - NONE            Associated redistribution matrix file
  ANCRFILE  - none            Associated ancillary response file
  XFLT0001  - none            XSPEC selection filter
  POISSERR  - TRUE            Whether Poissonian errors apply
  CHANTYPE  - PI              Whether channels have been corrected
  TLMIN1    - 0               First legal Detector channel
  DETCHANS  - 1024            No. of legal detector channels
  NCHAN     - 1024            No. of detector channels in dataset
  PHAVERSN  - 1.1.0           OGIP FITS version number
  STAT_ERR  - FALSE           Statistical Error
  SYS_ERR   - TRUE            Fractional Systematic Error
  QUALITY   - TRUE            Quality Flag
  GROUPING  - FALSE           Grouping Flag
  --------------------------------------------------------------------
  --------------------------------------------------------------------
 ...  QUALITY
 ...
 ...  -------
 ...  QUALITY
 ...  -------
 ...  Bad Channels (Channel - Channel)
 ...  ---------------------------------------------
 ...         0 -      31  have quality 5
 ...  ---------------------------------------------
 ...
 ...... exiting, changes written to file : ad33012010s010212_1.pi
 Command not found; type ? for a command listing
!xsel:ASCA > set mission ASCA
 
 Notes: XSELECT set up for      ASCA
 Keywords for time and pha are  TIME       PI
 Units of time are              s
 Default timing binsize =    16.00
 Keywords for images are          DETX       DETY
 Keywords for the WMAP are        DETX       DETY
 
!xsel:ASCA > set datadir .
 
Setting data directory to /data/data22/seq_proc/33012010.005/
Setting mkf directory to /data/data22/seq_proc/33012010.005/
 
!xsel:ASCA > read events ad33012010s000112h.evt
Got new instrument: SIS0
 
Setting: IMAGE binning    =    4
         WMAP binning     =    8
         Energy Column    =  PI
         Energy rebinning =    1
 
 
Getting Min and Max for Energy Column...
Got min and max for PI:     0   4095
 
Got the minimum time resolution of the read data:   4.0000
 Number of files read in:   1
 
******************** Observation Catalogue ********************
 
Data Directory is: /data/data22/seq_proc/33012010.005/
HK Directory is: /data/data22/seq_proc/33012010.005/
 
!xsel:ASCA-SIS0-BRIGHT2 > read events ad33012010s000312m.evt
 
Getting Min and Max for Energy Column...
Got min and max for PI:     0   4095
 
Got the minimum time resolution of the read data:   4.0000
 Number of files read in:   2
 
******************** Observation Catalogue ********************
 
Data Directory is: /data/data22/seq_proc/33012010.005/
HK Directory is: /data/data22/seq_proc/33012010.005/
 
!xsel:ASCA-SIS0-BRIGHT2 > set phaname PI
!xsel:ASCA-SIS0-BRIGHT2 > filter region ad33012010s032002_1.reg
!xsel:ASCA-SIS0-BRIGHT2 > filter region SIS0_NOTCHIP0.1
!xsel:ASCA-SIS0-BRIGHT2 > filter region SIS0_NOTCHIP2.1
!xsel:ASCA-SIS0-BRIGHT2 > filter region SIS0_NOTCHIP3.1
!xsel:ASCA-SIS0-BRIGHT2 > filter region SIS0_OFFCHIP.1
!xsel:ASCA-SIS0-BRIGHT2 > filter region ad33012010s010212.discrim
!xsel:ASCA-SIS0-BRIGHT2 > extract spectrum
!xsel:ASCA-SIS0-BRIGHT2 > save spectrum ad33012010s010212_1.pi group=yes
Wrote spectrum to ad33012010s010212_1.pi
!xsel:ASCA-SIS0-BRIGHT2 > exit save_session=no
-> Grouping ad33012010s010212_1.pi to 40 counts/bin
-> Standard Output From FTOOL grppha:
 
  -------------------------
  MANDATORY KEYWORDS/VALUES
  -------------------------
  --------------------------------------------------------------------
  --------------------------------------------------------------------
  EXTNAME   - SPECTRUM        Name of this BINTABLE
  TELESCOP  - ASCA            Mission/Satellite name
  INSTRUME  - SIS0            Instrument/Detector
  FILTER    -                 Instrument filter in use
  EXPOSURE  - 4591.6          Integration time (in secs) of PHA data
  AREASCAL  - 1.0000          Area scaling factor
  BACKSCAL  - 4.45898E-02     Background scaling factor
  BACKFILE  - NONE            Associated background file
  CORRSCAL  - 1.0000          Correlation scaling factor
  CORRFILE  - none            Associated correlation file
  RESPFILE  - NONE            Associated redistribution matrix file
  ANCRFILE  - none            Associated ancillary response file
  XFLT0001  - none            XSPEC selection filter
  POISSERR  - TRUE            Whether Poissonian errors apply
  CHANTYPE  - PI              Whether channels have been corrected
  TLMIN1    - 0               First legal Detector channel
  DETCHANS  - 1024            No. of legal detector channels
  NCHAN     - 1024            No. of detector channels in dataset
  PHAVERSN  - 1.1.0           OGIP FITS version number
  STAT_ERR  - FALSE           Statistical Error
  SYS_ERR   - TRUE            Fractional Systematic Error
  QUALITY   - TRUE            Quality Flag
  GROUPING  - FALSE           Grouping Flag
  --------------------------------------------------------------------
  --------------------------------------------------------------------
 ...
 ...  --------
 ...  GROUPING
 ...  --------
 ...  ---------------------------------------------
 ...  Channel Grouping (Channel-Channel) :
 ...         0 -      31  of undefined grouping (Channel quality=bad)
 ...        32 -     133  are grouped by a factor      102
 ...       134 -     174  are grouped by a factor       41
 ...       175 -     198  are grouped by a factor       24
 ...       199 -     220  are grouped by a factor       22
 ...       221 -     260  are grouped by a factor       20
 ...       261 -     279  are grouped by a factor       19
 ...       280 -     297  are grouped by a factor       18
 ...       298 -     322  are grouped by a factor       25
 ...       323 -     339  are grouped by a factor       17
 ...       340 -     361  are grouped by a factor       22
 ...       362 -     392  are grouped by a factor       31
 ...       393 -     427  are grouped by a factor       35
 ...       428 -     486  are grouped by a factor       59
 ...       487 -     714  are grouped by a factor      228
 ...       715 -    1005  are grouped by a factor      291
 ...      1006 -    1023  of undefined grouping (Channel quality=bad)
 ...  ---------------------------------------------
 ...
 ...... exiting, changes written to file : ad33012010s010212_1.pi
 ** grppha 2.6.0 completed successfully
-> Source occupies chip(s) 1
-> sis0c1p40_290296.fits already present in current directory
-> Generating ad33012010s010212_1.rmf
-> Standard Output From FTOOL sisrmg:
Sisrmg Version 1.1, Configured 04/97

  This version resolves *all* known keyword incompatibilities with
  other FTOOLS tasks.  If you have previously fudged *any* keywords
  in the PHA file to compensate, incorrect results will follow.
 
Setting 1st PHA channel to 0
Making v1.1 1180x1024 S0C1 Bright2 PI RMF
Calibration data from ./
Please stand by...
...Done.
-> Generating ad33012010s010212_1.arf with point=yes
-> Standard Output From FTOOL ascaarf:
ASCAARF vers 2.72  14 Mar 1997.
 
 Input WMAP array has size   39 by   37 bins
               expanded to   39 by   37 bins
 First WMAP bin is at detector pixel  328  336
   8 detector pixels per WMAP bin
 WMAP bin size is   0.21600 mm
                    0.21216 arcmin
 Selected region size is   51.381     arcmin^2
 Optical axis is detector pixel 662.72 559.02
 
 1180 energies from RMF file
 Effective area fudge applied
 Arf filter applied
 
 Point source at  487.00  487.00 (detector coordinates)
 Point source at   21.97    9.00 (WMAP bins wrt optical axis)
 Point source at    5.04   22.29 (... in polar coordinates)
 
 Total counts in region = 6.55000E+02
 Weighted mean angle from optical axis  =  5.238 arcmin
 
-> Standard Output From STOOL group_event_files:
1 ad33012010s100102h.evt 781
1 ad33012010s100302m.evt 781
-> Fetching SIS1_NOTCHIP0.1
-> Fetching SIS1_NOTCHIP1.1
-> Fetching SIS1_NOTCHIP2.1
-> Fetching SIS1_OFFCHIP.1
-> Extracting ad33012010s110102_1.pi from ad33012010s132002_1.reg and:
ad33012010s100102h.evt
ad33012010s100302m.evt
-> Standard Output From FTOOL xselect:
 
                         **  XSELECT V1.3   **
 
!> Enter session name >[xsel] xsel
 
 Notes: XSELECT set up for      ASCA
 Keywords for time and pha are  TIME       PI
 Units of time are              s
 Default timing binsize =    16.00
 Keywords for images are          DETX       DETY
 Keywords for the WMAP are        DETX       DETY
 
 
 
        OBJECT   DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME   NEVENTS  S1CCDPOW
      1 XY_ARI   BRIGHT   HIGH     29/01/96 17:42:55 0.39E+04      628 0001
 
 
 
        OBJECT   DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME   NEVENTS  S1CCDPOW
      1 XY_ARI   BRIGHT   HIGH     29/01/96 17:42:55 0.39E+04      628 0001
      2 XY_ARI   BRIGHT   MEDIUM   29/01/96 17:30:23 0.79E+03      153 0001
 
EXTRACTOR vers 2.0  11 Apr 1997.
 Getting FITS WCS Keywords
 Doing file: /data/data22/seq_proc/33012010.005/ad33012010s100102h.evt
          Total      Good    Bad: Region      Time     Phase       Cut
            628       502            126         0         0         0
 Doing file: /data/data22/seq_proc/33012010.005/ad33012010s100302m.evt
          Total      Good    Bad: Region      Time     Phase       Cut
            153       127             26         0         0         0
===============================================================================
   Grand Total      Good   Bad:  Region      Time     Phase       Cut
           781       629            152         0         0         0
   in    4729.61 seconds
 Spectrum         has      629 counts for 0.1330     counts/sec
 
  -------------------------
  MANDATORY KEYWORDS/VALUES
  -------------------------
  --------------------------------------------------------------------
  --------------------------------------------------------------------
  EXTNAME   - SPECTRUM        Name of this BINTABLE
  TELESCOP  - ASCA            Mission/Satellite name
  INSTRUME  - SIS1            Instrument/Detector
  FILTER    -                 Instrument filter in use
  EXPOSURE  - 4729.6          Integration time (in secs) of PHA data
  AREASCAL  - 1.0000          Area scaling factor
  BACKSCAL  - 4.07227E-02     Background scaling factor
  BACKFILE  - NONE            Associated background file
  CORRSCAL  - 1.0000          Correlation scaling factor
  CORRFILE  - none            Associated correlation file
  RESPFILE  - NONE            Associated redistribution matrix file
  ANCRFILE  - none            Associated ancillary response file
  XFLT0001  - none            XSPEC selection filter
  POISSERR  - TRUE            Whether Poissonian errors apply
  CHANTYPE  - PI              Whether channels have been corrected
  TLMIN1    - 0               First legal Detector channel
  DETCHANS  - 512             No. of legal detector channels
  NCHAN     - 512             No. of detector channels in dataset
  PHAVERSN  - 1.1.0           OGIP FITS version number
  STAT_ERR  - FALSE           Statistical Error
  SYS_ERR   - TRUE            Fractional Systematic Error
  QUALITY   - TRUE            Quality Flag
  GROUPING  - FALSE           Grouping Flag
  --------------------------------------------------------------------
  --------------------------------------------------------------------
 ...  QUALITY
 ...
 ...  -------
 ...  QUALITY
 ...  -------
 ...  Bad Channels (Channel - Channel)
 ...  ---------------------------------------------
 ...         0 -      15  have quality 5
 ...  ---------------------------------------------
 ...
 ...... exiting, changes written to file : ad33012010s110102_1.pi
 Command not found; type ? for a command listing
!xsel:ASCA > set mission ASCA
 
 Notes: XSELECT set up for      ASCA
 Keywords for time and pha are  TIME       PI
 Units of time are              s
 Default timing binsize =    16.00
 Keywords for images are          DETX       DETY
 Keywords for the WMAP are        DETX       DETY
 
!xsel:ASCA > set datadir .
 
Setting data directory to /data/data22/seq_proc/33012010.005/
Setting mkf directory to /data/data22/seq_proc/33012010.005/
 
!xsel:ASCA > read events ad33012010s100102h.evt
Got new instrument: SIS1
 
Setting: IMAGE binning    =    4
         WMAP binning     =    8
         Energy Column    =  PI
         Energy rebinning =    1
 
 
Getting Min and Max for Energy Column...
Got min and max for PI:     0   2047
 
Got the minimum time resolution of the read data:   4.0000
 Number of files read in:   1
 
******************** Observation Catalogue ********************
 
Data Directory is: /data/data22/seq_proc/33012010.005/
HK Directory is: /data/data22/seq_proc/33012010.005/
 
!xsel:ASCA-SIS1-BRIGHT > read events ad33012010s100302m.evt
 
Getting Min and Max for Energy Column...
Got min and max for PI:     0   2047
 
Got the minimum time resolution of the read data:   4.0000
 Number of files read in:   2
 
******************** Observation Catalogue ********************
 
Data Directory is: /data/data22/seq_proc/33012010.005/
HK Directory is: /data/data22/seq_proc/33012010.005/
 
!xsel:ASCA-SIS1-BRIGHT > set phaname PI
!xsel:ASCA-SIS1-BRIGHT > filter region ad33012010s132002_1.reg
!xsel:ASCA-SIS1-BRIGHT > filter region SIS1_NOTCHIP0.1
!xsel:ASCA-SIS1-BRIGHT > filter region SIS1_NOTCHIP1.1
!xsel:ASCA-SIS1-BRIGHT > filter region SIS1_NOTCHIP2.1
!xsel:ASCA-SIS1-BRIGHT > filter region SIS1_OFFCHIP.1
!xsel:ASCA-SIS1-BRIGHT > filter region ad33012010s110102.discrim
!xsel:ASCA-SIS1-BRIGHT > extract spectrum
!xsel:ASCA-SIS1-BRIGHT > save spectrum ad33012010s110102_1.pi group=yes
Wrote spectrum to ad33012010s110102_1.pi
!xsel:ASCA-SIS1-BRIGHT > exit save_session=no
-> Grouping ad33012010s110102_1.pi to 40 counts/bin
-> Standard Output From FTOOL grppha:
 
  -------------------------
  MANDATORY KEYWORDS/VALUES
  -------------------------
  --------------------------------------------------------------------
  --------------------------------------------------------------------
  EXTNAME   - SPECTRUM        Name of this BINTABLE
  TELESCOP  - ASCA            Mission/Satellite name
  INSTRUME  - SIS1            Instrument/Detector
  FILTER    -                 Instrument filter in use
  EXPOSURE  - 4729.6          Integration time (in secs) of PHA data
  AREASCAL  - 1.0000          Area scaling factor
  BACKSCAL  - 4.07227E-02     Background scaling factor
  BACKFILE  - NONE            Associated background file
  CORRSCAL  - 1.0000          Correlation scaling factor
  CORRFILE  - none            Associated correlation file
  RESPFILE  - NONE            Associated redistribution matrix file
  ANCRFILE  - none            Associated ancillary response file
  XFLT0001  - none            XSPEC selection filter
  POISSERR  - TRUE            Whether Poissonian errors apply
  CHANTYPE  - PI              Whether channels have been corrected
  TLMIN1    - 0               First legal Detector channel
  DETCHANS  - 512             No. of legal detector channels
  NCHAN     - 512             No. of detector channels in dataset
  PHAVERSN  - 1.1.0           OGIP FITS version number
  STAT_ERR  - FALSE           Statistical Error
  SYS_ERR   - TRUE            Fractional Systematic Error
  QUALITY   - TRUE            Quality Flag
  GROUPING  - FALSE           Grouping Flag
  --------------------------------------------------------------------
  --------------------------------------------------------------------
 ...
 ...  --------
 ...  GROUPING
 ...  --------
 ...  ---------------------------------------------
 ...  Channel Grouping (Channel-Channel) :
 ...         0 -      15  of undefined grouping (Channel quality=bad)
 ...        16 -      64  are grouped by a factor       49
 ...        65 -      78  are grouped by a factor       14
 ...        79 -      95  are grouped by a factor       17
 ...        96 -     110  are grouped by a factor       15
 ...       111 -     122  are grouped by a factor       12
 ...       123 -     132  are grouped by a factor       10
 ...       133 -     141  are grouped by a factor        9
 ...       142 -     153  are grouped by a factor       12
 ...       154 -     164  are grouped by a factor       11
 ...       165 -     177  are grouped by a factor       13
 ...       178 -     195  are grouped by a factor       18
 ...       196 -     215  are grouped by a factor       20
 ...       216 -     249  are grouped by a factor       34
 ...  ---------------------------------------------
 ...
 ...... exiting, changes written to file : ad33012010s110102_1.pi
 ** grppha 2.6.0 completed successfully
-> Source occupies chip(s) 3
-> Fetching sis1c3p40_290296.fits
-> Generating ad33012010s110102_1.rmf
-> Standard Output From FTOOL sisrmg:
Sisrmg Version 1.1, Configured 04/97

  This version resolves *all* known keyword incompatibilities with
  other FTOOLS tasks.  If you have previously fudged *any* keywords
  in the PHA file to compensate, incorrect results will follow.
 
Setting 1st PHA channel to 0
Making v1.1 1180x512 S1C3 Bright PI RMF
Calibration data from ./
Please stand by...
...Done.
-> Generating ad33012010s110102_1.arf with point=yes
-> Standard Output From FTOOL ascaarf:
ASCAARF vers 2.72  14 Mar 1997.
 
 Input WMAP array has size   40 by   33 bins
               expanded to   40 by   33 bins
 First WMAP bin is at detector pixel  320  368
   8 detector pixels per WMAP bin
 WMAP bin size is   0.21600 mm
                    0.21216 arcmin
 Selected region size is   46.925     arcmin^2
 Optical axis is detector pixel 618.28 773.83
 
 1180 energies from RMF file
 Effective area fudge applied
 Arf filter applied
 
 Point source at  483.00  503.00 (detector coordinates)
 Point source at   16.91   33.85 (WMAP bins wrt optical axis)
 Point source at    8.03   63.46 (... in polar coordinates)
 
 Total counts in region = 6.18000E+02
 Weighted mean angle from optical axis  =  7.623 arcmin
 
-> Standard Output From STOOL group_event_files:
1 ad33012010s100112h.evt 807
1 ad33012010s100312m.evt 807
-> SIS1_NOTCHIP0.1 already present in current directory
-> SIS1_NOTCHIP1.1 already present in current directory
-> SIS1_NOTCHIP2.1 already present in current directory
-> SIS1_OFFCHIP.1 already present in current directory
-> Extracting ad33012010s110212_1.pi from ad33012010s132002_1.reg and:
ad33012010s100112h.evt
ad33012010s100312m.evt
-> Standard Output From FTOOL xselect:
 
                         **  XSELECT V1.3   **
 
!> Enter session name >[xsel] xsel
 
 Notes: XSELECT set up for      ASCA
 Keywords for time and pha are  TIME       PI
 Units of time are              s
 Default timing binsize =    16.00
 Keywords for images are          DETX       DETY
 Keywords for the WMAP are        DETX       DETY
 
 
 
        OBJECT   DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME   NEVENTS  S1CCDPOW
      1 XY_ARI   BRIGHT2  HIGH     29/01/96 17:42:55 0.39E+04      649 0001
 
 
 
        OBJECT   DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME   NEVENTS  S1CCDPOW
      1 XY_ARI   BRIGHT2  HIGH     29/01/96 17:42:55 0.39E+04      649 0001
      2 XY_ARI   BRIGHT2  MEDIUM   29/01/96 17:30:23 0.79E+03      158 0001
 
EXTRACTOR vers 2.0  11 Apr 1997.
 Getting FITS WCS Keywords
 Doing file: /data/data22/seq_proc/33012010.005/ad33012010s100112h.evt
          Total      Good    Bad: Region      Time     Phase       Cut
            649       511            138         0         0         0
 Doing file: /data/data22/seq_proc/33012010.005/ad33012010s100312m.evt
          Total      Good    Bad: Region      Time     Phase       Cut
            158       131             27         0         0         0
===============================================================================
   Grand Total      Good   Bad:  Region      Time     Phase       Cut
           807       642            165         0         0         0
   in    4729.61 seconds
 Spectrum         has      642 counts for 0.1357     counts/sec
 
  -------------------------
  MANDATORY KEYWORDS/VALUES
  -------------------------
  --------------------------------------------------------------------
  --------------------------------------------------------------------
  EXTNAME   - SPECTRUM        Name of this BINTABLE
  TELESCOP  - ASCA            Mission/Satellite name
  INSTRUME  - SIS1            Instrument/Detector
  FILTER    -                 Instrument filter in use
  EXPOSURE  - 4729.6          Integration time (in secs) of PHA data
  AREASCAL  - 1.0000          Area scaling factor
  BACKSCAL  - 4.07227E-02     Background scaling factor
  BACKFILE  - NONE            Associated background file
  CORRSCAL  - 1.0000          Correlation scaling factor
  CORRFILE  - none            Associated correlation file
  RESPFILE  - NONE            Associated redistribution matrix file
  ANCRFILE  - none            Associated ancillary response file
  XFLT0001  - none            XSPEC selection filter
  POISSERR  - TRUE            Whether Poissonian errors apply
  CHANTYPE  - PI              Whether channels have been corrected
  TLMIN1    - 0               First legal Detector channel
  DETCHANS  - 1024            No. of legal detector channels
  NCHAN     - 1024            No. of detector channels in dataset
  PHAVERSN  - 1.1.0           OGIP FITS version number
  STAT_ERR  - FALSE           Statistical Error
  SYS_ERR   - TRUE            Fractional Systematic Error
  QUALITY   - TRUE            Quality Flag
  GROUPING  - FALSE           Grouping Flag
  --------------------------------------------------------------------
  --------------------------------------------------------------------
 ...  QUALITY
 ...
 ...  -------
 ...  QUALITY
 ...  -------
 ...  Bad Channels (Channel - Channel)
 ...  ---------------------------------------------
 ...         0 -      32  have quality 5
 ...  ---------------------------------------------
 ...
 ...... exiting, changes written to file : ad33012010s110212_1.pi
 Command not found; type ? for a command listing
!xsel:ASCA > set mission ASCA
 
 Notes: XSELECT set up for      ASCA
 Keywords for time and pha are  TIME       PI
 Units of time are              s
 Default timing binsize =    16.00
 Keywords for images are          DETX       DETY
 Keywords for the WMAP are        DETX       DETY
 
!xsel:ASCA > set datadir .
 
Setting data directory to /data/data22/seq_proc/33012010.005/
Setting mkf directory to /data/data22/seq_proc/33012010.005/
 
!xsel:ASCA > read events ad33012010s100112h.evt
Got new instrument: SIS1
 
Setting: IMAGE binning    =    4
         WMAP binning     =    8
         Energy Column    =  PI
         Energy rebinning =    1
 
 
Getting Min and Max for Energy Column...
Got min and max for PI:     0   4095
 
Got the minimum time resolution of the read data:   4.0000
 Number of files read in:   1
 
******************** Observation Catalogue ********************
 
Data Directory is: /data/data22/seq_proc/33012010.005/
HK Directory is: /data/data22/seq_proc/33012010.005/
 
!xsel:ASCA-SIS1-BRIGHT2 > read events ad33012010s100312m.evt
 
Getting Min and Max for Energy Column...
Got min and max for PI:     0   4095
 
Got the minimum time resolution of the read data:   4.0000
 Number of files read in:   2
 
******************** Observation Catalogue ********************
 
Data Directory is: /data/data22/seq_proc/33012010.005/
HK Directory is: /data/data22/seq_proc/33012010.005/
 
!xsel:ASCA-SIS1-BRIGHT2 > set phaname PI
!xsel:ASCA-SIS1-BRIGHT2 > filter region ad33012010s132002_1.reg
!xsel:ASCA-SIS1-BRIGHT2 > filter region SIS1_NOTCHIP0.1
!xsel:ASCA-SIS1-BRIGHT2 > filter region SIS1_NOTCHIP1.1
!xsel:ASCA-SIS1-BRIGHT2 > filter region SIS1_NOTCHIP2.1
!xsel:ASCA-SIS1-BRIGHT2 > filter region SIS1_OFFCHIP.1
!xsel:ASCA-SIS1-BRIGHT2 > filter region ad33012010s110212.discrim
!xsel:ASCA-SIS1-BRIGHT2 > extract spectrum
!xsel:ASCA-SIS1-BRIGHT2 > save spectrum ad33012010s110212_1.pi group=yes
Wrote spectrum to ad33012010s110212_1.pi
!xsel:ASCA-SIS1-BRIGHT2 > exit save_session=no
-> Grouping ad33012010s110212_1.pi to 40 counts/bin
-> Standard Output From FTOOL grppha:
 
  -------------------------
  MANDATORY KEYWORDS/VALUES
  -------------------------
  --------------------------------------------------------------------
  --------------------------------------------------------------------
  EXTNAME   - SPECTRUM        Name of this BINTABLE
  TELESCOP  - ASCA            Mission/Satellite name
  INSTRUME  - SIS1            Instrument/Detector
  FILTER    -                 Instrument filter in use
  EXPOSURE  - 4729.6          Integration time (in secs) of PHA data
  AREASCAL  - 1.0000          Area scaling factor
  BACKSCAL  - 4.07227E-02     Background scaling factor
  BACKFILE  - NONE            Associated background file
  CORRSCAL  - 1.0000          Correlation scaling factor
  CORRFILE  - none            Associated correlation file
  RESPFILE  - NONE            Associated redistribution matrix file
  ANCRFILE  - none            Associated ancillary response file
  XFLT0001  - none            XSPEC selection filter
  POISSERR  - TRUE            Whether Poissonian errors apply
  CHANTYPE  - PI              Whether channels have been corrected
  TLMIN1    - 0               First legal Detector channel
  DETCHANS  - 1024            No. of legal detector channels
  NCHAN     - 1024            No. of detector channels in dataset
  PHAVERSN  - 1.1.0           OGIP FITS version number
  STAT_ERR  - FALSE           Statistical Error
  SYS_ERR   - TRUE            Fractional Systematic Error
  QUALITY   - TRUE            Quality Flag
  GROUPING  - FALSE           Grouping Flag
  --------------------------------------------------------------------
  --------------------------------------------------------------------
 ...
 ...  --------
 ...  GROUPING
 ...  --------
 ...  ---------------------------------------------
 ...  Channel Grouping (Channel-Channel) :
 ...         0 -      32  of undefined grouping (Channel quality=bad)
 ...        33 -     128  are grouped by a factor       96
 ...       129 -     155  are grouped by a factor       27
 ...       156 -     190  are grouped by a factor       35
 ...       191 -     219  are grouped by a factor       29
 ...       220 -     243  are grouped by a factor       24
 ...       244 -     281  are grouped by a factor       19
 ...       282 -     304  are grouped by a factor       23
 ...       305 -     323  are grouped by a factor       19
 ...       324 -     351  are grouped by a factor       28
 ...       352 -     386  are grouped by a factor       35
 ...       387 -     420  are grouped by a factor       34
 ...       421 -     457  are grouped by a factor       37
 ...       458 -     601  are grouped by a factor      144
 ...       602 -     918  are grouped by a factor      317
 ...       919 -    1023  of undefined grouping (Channel quality=bad)
 ...  ---------------------------------------------
 ...
 ...... exiting, changes written to file : ad33012010s110212_1.pi
 ** grppha 2.6.0 completed successfully
-> Source occupies chip(s) 3
-> sis1c3p40_290296.fits already present in current directory
-> Generating ad33012010s110212_1.rmf
-> Standard Output From FTOOL sisrmg:
Sisrmg Version 1.1, Configured 04/97

  This version resolves *all* known keyword incompatibilities with
  other FTOOLS tasks.  If you have previously fudged *any* keywords
  in the PHA file to compensate, incorrect results will follow.
 
Setting 1st PHA channel to 0
Making v1.1 1180x1024 S1C3 Bright2 PI RMF
Calibration data from ./
Please stand by...
...Done.
-> Generating ad33012010s110212_1.arf with point=yes
-> Standard Output From FTOOL ascaarf:
ASCAARF vers 2.72  14 Mar 1997.
 
 Input WMAP array has size   40 by   33 bins
               expanded to   40 by   33 bins
 First WMAP bin is at detector pixel  320  368
   8 detector pixels per WMAP bin
 WMAP bin size is   0.21600 mm
                    0.21216 arcmin
 Selected region size is   46.925     arcmin^2
 Optical axis is detector pixel 618.28 773.83
 
 1180 energies from RMF file
 Effective area fudge applied
 Arf filter applied
 
 Point source at  483.00  503.00 (detector coordinates)
 Point source at   16.91   33.85 (WMAP bins wrt optical axis)
 Point source at    8.03   63.46 (... in polar coordinates)
 
 Total counts in region = 6.31000E+02
 Weighted mean angle from optical axis  =  7.633 arcmin
 
-> Standard Output From STOOL group_event_files:
1 ad33012010g200170h.evt 1921
1 ad33012010g200270l.evt 1921
1 ad33012010g200370m.evt 1921
-> GIS2_REGION256.4 already present in current directory
-> Extracting ad33012010g210170_1.pi from ad33012010g225670_1.reg and:
ad33012010g200170h.evt
ad33012010g200270l.evt
ad33012010g200370m.evt
-> Standard Output From FTOOL xselect:
 
                         **  XSELECT V1.3   **
 
!> Enter session name >[xsel] xsel
 
 Notes: XSELECT set up for      ASCA
 Keywords for time and pha are  TIME       PI
 Units of time are              s
 Default timing binsize =    16.00
 Keywords for images are          DETX       DETY
 Keywords for the WMAP are        DETX       DETY
 
 
 
        OBJECT   DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME   NEVENTS  PHA_BINS
      1 XY_ARI   PH       HIGH     29/01/96 17:43:01 0.38E+04     1358     1024
 
 
 
        OBJECT   DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME   NEVENTS  PHA_BINS
      1 XY_ARI   PH       HIGH     29/01/96 17:43:01 0.38E+04     1358     1024
      2 XY_ARI   PH       LOW      29/01/96 18:46:29 0.32E+02       16     1024
 
 
 
        OBJECT   DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME   NEVENTS  PHA_BINS
      1 XY_ARI   PH       HIGH     29/01/96 17:43:01 0.38E+04     1358     1024
      2 XY_ARI   PH       LOW      29/01/96 18:46:29 0.32E+02       16     1024
      3 XY_ARI   PH       MEDIUM   29/01/96 17:30:29 0.13E+04      547     1024
 
EXTRACTOR vers 2.0  11 Apr 1997.
 Getting FITS WCS Keywords
 Doing file: /data/data22/seq_proc/33012010.005/ad33012010g200170h.evt
          Total      Good    Bad: Region      Time     Phase       Cut
           1358       450            908         0         0         0
 Doing file: /data/data22/seq_proc/33012010.005/ad33012010g200270l.evt
          Total      Good    Bad: Region      Time     Phase       Cut
             16         7              9         0         0         0
 Doing file: /data/data22/seq_proc/33012010.005/ad33012010g200370m.evt
          Total      Good    Bad: Region      Time     Phase       Cut
            547       193            354         0         0         0
===============================================================================
   Grand Total      Good   Bad:  Region      Time     Phase       Cut
          1921       650           1271         0         0         0
   in    5190.01 seconds
 Spectrum         has      650 counts for 0.1252     counts/sec
 
  -------------------------
  MANDATORY KEYWORDS/VALUES
  -------------------------
  --------------------------------------------------------------------
  --------------------------------------------------------------------
  EXTNAME   - SPECTRUM        Name of this BINTABLE
  TELESCOP  - ASCA            Mission/Satellite name
  INSTRUME  - GIS2            Instrument/Detector
  FILTER    -                 Instrument filter in use
  EXPOSURE  - 5190.0          Integration time (in secs) of PHA data
  AREASCAL  - 1.0000          Area scaling factor
  BACKSCAL  - 2.90070E-02     Background scaling factor
  BACKFILE  - NONE            Associated background file
  CORRSCAL  - 1.0000          Correlation scaling factor
  CORRFILE  - none            Associated correlation file
  RESPFILE  - NONE            Associated redistribution matrix file
  ANCRFILE  - none            Associated ancillary response file
  XFLT0001  - none            XSPEC selection filter
  POISSERR  - TRUE            Whether Poissonian errors apply
  CHANTYPE  - PI              Whether channels have been corrected
  TLMIN1    - 0               First legal Detector channel
  DETCHANS  - 1024            No. of legal detector channels
  NCHAN     - 1024            No. of detector channels in dataset
  PHAVERSN  - 1992a           OGIP FITS version number
  STAT_ERR  - FALSE           Statistical Error
  SYS_ERR   - TRUE            Fractional Systematic Error
  QUALITY   - TRUE            Quality Flag
  GROUPING  - FALSE           Grouping Flag
  --------------------------------------------------------------------
  --------------------------------------------------------------------
 ...
 ...  --------
 ...  GROUPING
 ...  --------
 ...  ---------------------------------------------
 ...  Channel Grouping (Channel-Channel) :
 ...  ---------------------------------------------
 ...
 ...... exiting, changes written to file : ad33012010g210170_1.pi
 Command not found; type ? for a command listing
!xsel:ASCA > set mission ASCA
 
 Notes: XSELECT set up for      ASCA
 Keywords for time and pha are  TIME       PI
 Units of time are              s
 Default timing binsize =    16.00
 Keywords for images are          DETX       DETY
 Keywords for the WMAP are        DETX       DETY
 
!xsel:ASCA > set datadir .
 
Setting data directory to /data/data22/seq_proc/33012010.005/
Setting mkf directory to /data/data22/seq_proc/33012010.005/
 
!xsel:ASCA > read events ad33012010g200170h.evt
Got new instrument: GIS2
 
Setting: IMAGE binning    =    1
         WMAP binning     =    1
         Energy Column    =  PI
         Energy rebinning =    1
 
 
Getting Min and Max for Energy Column...
Got min and max for PI:     0   1023
 
Got the minimum time resolution of the read data:  0.62500E-01
 Number of files read in:   1
 
******************** Observation Catalogue ********************
 
Data Directory is: /data/data22/seq_proc/33012010.005/
HK Directory is: /data/data22/seq_proc/33012010.005/
 
!xsel:ASCA-GIS2-PH > read events ad33012010g200270l.evt
 
Getting Min and Max for Energy Column...
Got min and max for PI:     0   1023
 
Got the minimum time resolution of the read data:   2.0000
 Number of files read in:   2
 
******************** Observation Catalogue ********************
 
Data Directory is: /data/data22/seq_proc/33012010.005/
HK Directory is: /data/data22/seq_proc/33012010.005/
 
!xsel:ASCA-GIS2-PH > read events ad33012010g200370m.evt
 
Getting Min and Max for Energy Column...
Got min and max for PI:     0   1023
 
Got the minimum time resolution of the read data:  0.50000
 Number of files read in:   3
 
******************** Observation Catalogue ********************
 
Data Directory is: /data/data22/seq_proc/33012010.005/
HK Directory is: /data/data22/seq_proc/33012010.005/
 
!xsel:ASCA-GIS2-PH > set phaname PI
!xsel:ASCA-GIS2-PH > filter region ad33012010g225670_1.reg
!xsel:ASCA-GIS2-PH > filter region GIS2_REGION256.4
!xsel:ASCA-GIS2-PH > extract spectrum
!xsel:ASCA-GIS2-PH > save spectrum ad33012010g210170_1.pi group=yes
Wrote spectrum to ad33012010g210170_1.pi
!xsel:ASCA-GIS2-PH > exit save_session=no
-> Correcting ad33012010g210170_1.pi for dead time
-> Standard Output From FTOOL deadtime:
... read all the files from deadlist.tmp
-> Grouping ad33012010g210170_1.pi to 40 counts/bin
-> Standard Output From FTOOL grppha:
 
  -------------------------
  MANDATORY KEYWORDS/VALUES
  -------------------------
  --------------------------------------------------------------------
  --------------------------------------------------------------------
  EXTNAME   - SPECTRUM        Name of this BINTABLE
  TELESCOP  - ASCA            Mission/Satellite name
  INSTRUME  - GIS2            Instrument/Detector
  FILTER    -                 Instrument filter in use
  EXPOSURE  - 5190.0          Integration time (in secs) of PHA data
  AREASCAL  - 1.0000          Area scaling factor
  BACKSCAL  - 2.90070E-02     Background scaling factor
  BACKFILE  - NONE            Associated background file
  CORRSCAL  - 1.0000          Correlation scaling factor
  CORRFILE  - none            Associated correlation file
  RESPFILE  - NONE            Associated redistribution matrix file
  ANCRFILE  - none            Associated ancillary response file
  XFLT0001  - none            XSPEC selection filter
  POISSERR  - TRUE            Whether Poissonian errors apply
  CHANTYPE  - PI              Whether channels have been corrected
  TLMIN1    - 0               First legal Detector channel
  DETCHANS  - 1024            No. of legal detector channels
  NCHAN     - 1024            No. of detector channels in dataset
  PHAVERSN  - 1.1.0           OGIP FITS version number
  STAT_ERR  - FALSE           Statistical Error
  SYS_ERR   - TRUE            Fractional Systematic Error
  QUALITY   - TRUE            Quality Flag
  GROUPING  - TRUE            Grouping Flag
  --------------------------------------------------------------------
  --------------------------------------------------------------------
 ...
 ...  --------
 ...  GROUPING
 ...  --------
 ...  ---------------------------------------------
 ...  Channel Grouping (Channel-Channel) :
 ...         0 -     141  are grouped by a factor      142
 ...       142 -     208  are grouped by a factor       67
 ...       209 -     242  are grouped by a factor       34
 ...       243 -     270  are grouped by a factor       28
 ...       271 -     299  are grouped by a factor       29
 ...       300 -     331  are grouped by a factor       32
 ...       332 -     375  are grouped by a factor       22
 ...       376 -     406  are grouped by a factor       31
 ...       407 -     426  are grouped by a factor       20
 ...       427 -     457  are grouped by a factor       31
 ...       458 -     492  are grouped by a factor       35
 ...       493 -     528  are grouped by a factor       36
 ...       529 -     565  are grouped by a factor       37
 ...       566 -     654  are grouped by a factor       89
 ...       655 -     947  are grouped by a factor      293
 ...       948 -    1023  of undefined grouping (Channel quality=bad)
 ...  ---------------------------------------------
 ...
 ...... exiting, changes written to file : ad33012010g210170_1.pi
 ** grppha 2.6.0 completed successfully
-> Fetching gis2v4_0.rmf
-> Fetching s2bev1.fits
-> Fetching s2gridv3.fits
-> Generating ad33012010g210170_1.arf with point=yes
-> Standard Output From FTOOL ascaarf:
ASCAARF vers 2.72  14 Mar 1997.
 
 Input WMAP array has size   49 by   49 bins
               expanded to  128 by  128 bins
 First WMAP bin is at detector pixel   47   53
   1 detector pixels per WMAP bin
 WMAP bin size is   0.25000 mm
                    0.24555 arcmin
 Selected region size is   114.65     arcmin^2
 Optical axis is detector pixel 133.00 130.96
 
  201 energies from RMF file
 Effective area fudge applied
 Arf filter applied
 
 Point source at  109.00  115.00 (detector coordinates)
 Point source at   24.00   15.96 (WMAP bins wrt optical axis)
 Point source at    7.08   33.62 (... in polar coordinates)
 
 Total counts in region = 6.50000E+02
 Weighted mean angle from optical axis  =  7.117 arcmin
 
-> Standard Output From STOOL group_event_files:
1 ad33012010g300170h.evt 2193
1 ad33012010g300270l.evt 2193
1 ad33012010g300370m.evt 2193
-> GIS3_REGION256.4 already present in current directory
-> Extracting ad33012010g310170_1.pi from ad33012010g325670_1.reg and:
ad33012010g300170h.evt
ad33012010g300270l.evt
ad33012010g300370m.evt
-> Standard Output From FTOOL xselect:
 
                         **  XSELECT V1.3   **
 
!> Enter session name >[xsel] xsel
 
 Notes: XSELECT set up for      ASCA
 Keywords for time and pha are  TIME       PI
 Units of time are              s
 Default timing binsize =    16.00
 Keywords for images are          DETX       DETY
 Keywords for the WMAP are        DETX       DETY
 
 
 
        OBJECT   DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME   NEVENTS  PHA_BINS
      1 XY_ARI   PH       HIGH     29/01/96 17:43:01 0.38E+04     1552     1024
 
 
 
        OBJECT   DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME   NEVENTS  PHA_BINS
      1 XY_ARI   PH       HIGH     29/01/96 17:43:01 0.38E+04     1552     1024
      2 XY_ARI   PH       LOW      29/01/96 18:46:29 0.32E+02       18     1024
 
 
 
        OBJECT   DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME   NEVENTS  PHA_BINS
      1 XY_ARI   PH       HIGH     29/01/96 17:43:01 0.38E+04     1552     1024
      2 XY_ARI   PH       LOW      29/01/96 18:46:29 0.32E+02       18     1024
      3 XY_ARI   PH       MEDIUM   29/01/96 17:30:29 0.13E+04      623     1024
 
EXTRACTOR vers 2.0  11 Apr 1997.
 Getting FITS WCS Keywords
 Doing file: /data/data22/seq_proc/33012010.005/ad33012010g300170h.evt
          Total      Good    Bad: Region      Time     Phase       Cut
           1552       563            989         0         0         0
 Doing file: /data/data22/seq_proc/33012010.005/ad33012010g300270l.evt
          Total      Good    Bad: Region      Time     Phase       Cut
             18        10              8         0         0         0
 Doing file: /data/data22/seq_proc/33012010.005/ad33012010g300370m.evt
          Total      Good    Bad: Region      Time     Phase       Cut
            623       244            379         0         0         0
===============================================================================
   Grand Total      Good   Bad:  Region      Time     Phase       Cut
          2193       817           1376         0         0         0
   in    5187.97 seconds
 Spectrum         has      817 counts for 0.1575     counts/sec
 
  -------------------------
  MANDATORY KEYWORDS/VALUES
  -------------------------
  --------------------------------------------------------------------
  --------------------------------------------------------------------
  EXTNAME   - SPECTRUM        Name of this BINTABLE
  TELESCOP  - ASCA            Mission/Satellite name
  INSTRUME  - GIS3            Instrument/Detector
  FILTER    -                 Instrument filter in use
  EXPOSURE  - 5188.0          Integration time (in secs) of PHA data
  AREASCAL  - 1.0000          Area scaling factor
  BACKSCAL  - 2.90070E-02     Background scaling factor
  BACKFILE  - NONE            Associated background file
  CORRSCAL  - 1.0000          Correlation scaling factor
  CORRFILE  - none            Associated correlation file
  RESPFILE  - NONE            Associated redistribution matrix file
  ANCRFILE  - none            Associated ancillary response file
  XFLT0001  - none            XSPEC selection filter
  POISSERR  - TRUE            Whether Poissonian errors apply
  CHANTYPE  - PI              Whether channels have been corrected
  TLMIN1    - 0               First legal Detector channel
  DETCHANS  - 1024            No. of legal detector channels
  NCHAN     - 1024            No. of detector channels in dataset
  PHAVERSN  - 1992a           OGIP FITS version number
  STAT_ERR  - FALSE           Statistical Error
  SYS_ERR   - TRUE            Fractional Systematic Error
  QUALITY   - TRUE            Quality Flag
  GROUPING  - FALSE           Grouping Flag
  --------------------------------------------------------------------
  --------------------------------------------------------------------
 ...
 ...  --------
 ...  GROUPING
 ...  --------
 ...  ---------------------------------------------
 ...  Channel Grouping (Channel-Channel) :
 ...  ---------------------------------------------
 ...
 ...... exiting, changes written to file : ad33012010g310170_1.pi
 Command not found; type ? for a command listing
!xsel:ASCA > set mission ASCA
 
 Notes: XSELECT set up for      ASCA
 Keywords for time and pha are  TIME       PI
 Units of time are              s
 Default timing binsize =    16.00
 Keywords for images are          DETX       DETY
 Keywords for the WMAP are        DETX       DETY
 
!xsel:ASCA > set datadir .
 
Setting data directory to /data/data22/seq_proc/33012010.005/
Setting mkf directory to /data/data22/seq_proc/33012010.005/
 
!xsel:ASCA > read events ad33012010g300170h.evt
Got new instrument: GIS3
 
Setting: IMAGE binning    =    1
         WMAP binning     =    1
         Energy Column    =  PI
         Energy rebinning =    1
 
 
Getting Min and Max for Energy Column...
Got min and max for PI:     0   1023
 
Got the minimum time resolution of the read data:  0.62500E-01
 Number of files read in:   1
 
******************** Observation Catalogue ********************
 
Data Directory is: /data/data22/seq_proc/33012010.005/
HK Directory is: /data/data22/seq_proc/33012010.005/
 
!xsel:ASCA-GIS3-PH > read events ad33012010g300270l.evt
 
Getting Min and Max for Energy Column...
Got min and max for PI:     0   1023
 
Got the minimum time resolution of the read data:   2.0000
 Number of files read in:   2
 
******************** Observation Catalogue ********************
 
Data Directory is: /data/data22/seq_proc/33012010.005/
HK Directory is: /data/data22/seq_proc/33012010.005/
 
!xsel:ASCA-GIS3-PH > read events ad33012010g300370m.evt
 
Getting Min and Max for Energy Column...
Got min and max for PI:     0   1023
 
Got the minimum time resolution of the read data:  0.50000
 Number of files read in:   3
 
******************** Observation Catalogue ********************
 
Data Directory is: /data/data22/seq_proc/33012010.005/
HK Directory is: /data/data22/seq_proc/33012010.005/
 
!xsel:ASCA-GIS3-PH > set phaname PI
!xsel:ASCA-GIS3-PH > filter region ad33012010g325670_1.reg
!xsel:ASCA-GIS3-PH > filter region GIS3_REGION256.4
!xsel:ASCA-GIS3-PH > extract spectrum
!xsel:ASCA-GIS3-PH > save spectrum ad33012010g310170_1.pi group=yes
Wrote spectrum to ad33012010g310170_1.pi
!xsel:ASCA-GIS3-PH > exit save_session=no
-> Correcting ad33012010g310170_1.pi for dead time
-> Standard Output From FTOOL deadtime:
... read all the files from deadlist.tmp
-> Grouping ad33012010g310170_1.pi to 40 counts/bin
-> Standard Output From FTOOL grppha:
 
  -------------------------
  MANDATORY KEYWORDS/VALUES
  -------------------------
  --------------------------------------------------------------------
  --------------------------------------------------------------------
  EXTNAME   - SPECTRUM        Name of this BINTABLE
  TELESCOP  - ASCA            Mission/Satellite name
  INSTRUME  - GIS3            Instrument/Detector
  FILTER    -                 Instrument filter in use
  EXPOSURE  - 5188.0          Integration time (in secs) of PHA data
  AREASCAL  - 1.0000          Area scaling factor
  BACKSCAL  - 2.90070E-02     Background scaling factor
  BACKFILE  - NONE            Associated background file
  CORRSCAL  - 1.0000          Correlation scaling factor
  CORRFILE  - none            Associated correlation file
  RESPFILE  - NONE            Associated redistribution matrix file
  ANCRFILE  - none            Associated ancillary response file
  XFLT0001  - none            XSPEC selection filter
  POISSERR  - TRUE            Whether Poissonian errors apply
  CHANTYPE  - PI              Whether channels have been corrected
  TLMIN1    - 0               First legal Detector channel
  DETCHANS  - 1024            No. of legal detector channels
  NCHAN     - 1024            No. of detector channels in dataset
  PHAVERSN  - 1.1.0           OGIP FITS version number
  STAT_ERR  - FALSE           Statistical Error
  SYS_ERR   - TRUE            Fractional Systematic Error
  QUALITY   - TRUE            Quality Flag
  GROUPING  - TRUE            Grouping Flag
  --------------------------------------------------------------------
  --------------------------------------------------------------------
 ...
 ...  --------
 ...  GROUPING
 ...  --------
 ...  ---------------------------------------------
 ...  Channel Grouping (Channel-Channel) :
 ...         0 -     151  are grouped by a factor      152
 ...       152 -     185  are grouped by a factor       34
 ...       186 -     218  are grouped by a factor       33
 ...       219 -     243  are grouped by a factor       25
 ...       244 -     266  are grouped by a factor       23
 ...       267 -     280  are grouped by a factor       14
 ...       281 -     306  are grouped by a factor       26
 ...       307 -     328  are grouped by a factor       22
 ...       329 -     352  are grouped by a factor       24
 ...       353 -     371  are grouped by a factor       19
 ...       372 -     392  are grouped by a factor       21
 ...       393 -     415  are grouped by a factor       23
 ...       416 -     436  are grouped by a factor       21
 ...       437 -     460  are grouped by a factor       24
 ...       461 -     487  are grouped by a factor       27
 ...       488 -     521  are grouped by a factor       34
 ...       522 -     551  are grouped by a factor       30
 ...       552 -     608  are grouped by a factor       57
 ...       609 -     720  are grouped by a factor      112
 ...       721 -     926  are grouped by a factor      206
 ...       927 -    1023  of undefined grouping (Channel quality=bad)
 ...  ---------------------------------------------
 ...
 ...... exiting, changes written to file : ad33012010g310170_1.pi
 ** grppha 2.6.0 completed successfully
-> Fetching gis3v4_0.rmf
-> Fetching s3bev1.fits
-> Fetching s3gridv3.fits
-> Generating ad33012010g310170_1.arf with point=yes
-> Standard Output From FTOOL ascaarf:
ASCAARF vers 2.72  14 Mar 1997.
 
 Input WMAP array has size   49 by   49 bins
               expanded to  128 by  128 bins
 First WMAP bin is at detector pixel   53   53
   1 detector pixels per WMAP bin
 WMAP bin size is   0.25000 mm
                    0.24555 arcmin
 Selected region size is   114.65     arcmin^2
 Optical axis is detector pixel 119.36 134.44
 
  201 energies from RMF file
 Effective area fudge applied
 Arf filter applied
 
 Point source at  115.00  115.00 (detector coordinates)
 Point source at    4.36   19.44 (WMAP bins wrt optical axis)
 Point source at    4.89   77.36 (... in polar coordinates)
 
 Total counts in region = 8.17000E+02
 Weighted mean angle from optical axis  =  5.158 arcmin
 
-> Plotting ad33012010g210170_1_pi.ps from ad33012010g210170_1.pi
-> Standard Output From STOOL xspec:
 
               XSPEC 9.01 15:17:42 17-May-98
 
 Plot device not set, use "cpd" to set it
 
 Type "help" or "?" for further information
!XSPEC> data ad33012010g210170_1.pi
 Net count rate (cts/s) for file   1  0.1252    +/-  5.1808E-03
   1 data set is in use
!XSPEC> setplot energy
!XSPEC> ignore bad
!XSPEC> iplot
!PLT> log y on
!PLT> rescale y
!PLT> hard /ps
!PLT> quit
!XSPEC> exit
!Do you really want to exit (y) y
 XSPEC: quit
-> Plotting ad33012010g310170_1_pi.ps from ad33012010g310170_1.pi
-> Standard Output From STOOL xspec:
 
               XSPEC 9.01 15:17:58 17-May-98
 
 Plot device not set, use "cpd" to set it
 
 Type "help" or "?" for further information
!XSPEC> data ad33012010g310170_1.pi
 Net count rate (cts/s) for file   1  0.1575    +/-  5.8115E-03
   1 data set is in use
!XSPEC> setplot energy
!XSPEC> ignore bad
!XSPEC> iplot
!PLT> log y on
!PLT> rescale y
!PLT> hard /ps
!PLT> quit
!XSPEC> exit
!Do you really want to exit (y) y
 XSPEC: quit
-> Plotting ad33012010s010102_1_pi.ps from ad33012010s010102_1.pi
-> Standard Output From STOOL xspec:
 
               XSPEC 9.01 15:18:13 17-May-98
 
 Plot device not set, use "cpd" to set it
 
 Type "help" or "?" for further information
!XSPEC> data ad33012010s010102_1.pi
 Net count rate (cts/s) for file   1  0.1381    +/-  5.5525E-03
   1 data set is in use
!XSPEC> setplot energy
!XSPEC> ignore bad
!XSPEC> iplot
!PLT> log y on
!PLT> rescale y
!PLT> hard /ps
!PLT> quit
!XSPEC> exit
!Do you really want to exit (y) y
 XSPEC: quit
-> Plotting ad33012010s010212_1_pi.ps from ad33012010s010212_1.pi
-> Standard Output From STOOL xspec:
 
               XSPEC 9.01 15:18:27 17-May-98
 
 Plot device not set, use "cpd" to set it
 
 Type "help" or "?" for further information
!XSPEC> data ad33012010s010212_1.pi
 Net count rate (cts/s) for file   1  0.1446    +/-  5.8154E-03
   1 data set is in use
!XSPEC> setplot energy
!XSPEC> ignore bad
!XSPEC> iplot
!PLT> log y on
!PLT> rescale y
!PLT> hard /ps
!PLT> quit
!XSPEC> exit
!Do you really want to exit (y) y
 XSPEC: quit
-> Plotting ad33012010s110102_1_pi.ps from ad33012010s110102_1.pi
-> Standard Output From STOOL xspec:
 
               XSPEC 9.01 15:18:44 17-May-98
 
 Plot device not set, use "cpd" to set it
 
 Type "help" or "?" for further information
!XSPEC> data ad33012010s110102_1.pi
 Net count rate (cts/s) for file   1  0.1330    +/-  5.3614E-03
   1 data set is in use
!XSPEC> setplot energy
!XSPEC> ignore bad
!XSPEC> iplot
!PLT> log y on
!PLT> rescale y
!PLT> hard /ps
!PLT> quit
!XSPEC> exit
!Do you really want to exit (y) y
 XSPEC: quit
-> Plotting ad33012010s110212_1_pi.ps from ad33012010s110212_1.pi
-> Standard Output From STOOL xspec:
 
               XSPEC 9.01 15:19:00 17-May-98
 
 Plot device not set, use "cpd" to set it
 
 Type "help" or "?" for further information
!XSPEC> data ad33012010s110212_1.pi
 Net count rate (cts/s) for file   1  0.1357    +/-  5.8709E-03
   1 data set is in use
!XSPEC> setplot energy
!XSPEC> ignore bad
!XSPEC> iplot
!PLT> log y on
!PLT> rescale y
!PLT> hard /ps
!PLT> quit
!XSPEC> exit
!Do you really want to exit (y) y
 XSPEC: quit

Extracting light curves ( 15:19:11 )

-> TIMEDEL=4.0000000000E+00 for ad33012010s000102h.evt
-> TIMEDEL=4.0000000000E+00 for ad33012010s000302m.evt
-> Minimum bin size is 4.0000000000E+00 seconds
-> Extracting events from region ad33012010s032002_1.reg
-> ... and files: ad33012010s000102h.evt ad33012010s000302m.evt
-> Standard Output From FTOOL xselect:
 
                         **  XSELECT V1.3   **
 
!> Enter session name >[xsel] xsel
 
 Notes: XSELECT set up for      ASCA
 Keywords for time and pha are  TIME       PI
 Units of time are              s
 Default timing binsize =    16.00
 Keywords for images are          DETX       DETY
 Keywords for the WMAP are        DETX       DETY
 
 
 
        OBJECT   DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME   NEVENTS  S0CCDPOW
      1 XY_ARI   BRIGHT   HIGH     29/01/96 17:42:55 0.39E+04      661 0100
 
 
 
        OBJECT   DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME   NEVENTS  S0CCDPOW
      1 XY_ARI   BRIGHT   HIGH     29/01/96 17:42:55 0.39E+04      661 0100
      2 XY_ARI   BRIGHT   MEDIUM   29/01/96 17:30:23 0.70E+03      151 0100
 
EXTRACTOR vers 2.0  11 Apr 1997.
 Doing file: /data/data22/seq_proc/33012010.005/ad33012010s000102h.evt
          Total      Good    Bad: Region      Time     Phase       Cut
            661       520            141         0         0         0
 Writing events file
    520 events written to the output file
 Doing file: /data/data22/seq_proc/33012010.005/ad33012010s000302m.evt
          Total      Good    Bad: Region      Time     Phase       Cut
            151       117             34         0         0         0
 Writing events file
    637 events written to the output file
===============================================================================
   Grand Total      Good   Bad:  Region      Time     Phase       Cut
           812       637            175         0         0         0
   in    4591.64 seconds
 Command not found; type ? for a command listing
!xsel:ASCA > set mission ASCA
 
 Notes: XSELECT set up for      ASCA
 Keywords for time and pha are  TIME       PI
 Units of time are              s
 Default timing binsize =    16.00
 Keywords for images are          DETX       DETY
 Keywords for the WMAP are        DETX       DETY
 
!xsel:ASCA > set datadir .
 
Setting data directory to /data/data22/seq_proc/33012010.005/
Setting mkf directory to /data/data22/seq_proc/33012010.005/
 
!xsel:ASCA > read events ad33012010s000102h.evt
Got new instrument: SIS0
 
Setting: IMAGE binning    =    4
         WMAP binning     =    8
         Energy Column    =  PI
         Energy rebinning =    1
 
 
Getting Min and Max for Energy Column...
Got min and max for PI:     0   2047
 
Got the minimum time resolution of the read data:   4.0000
 Number of files read in:   1
 
******************** Observation Catalogue ********************
 
Data Directory is: /data/data22/seq_proc/33012010.005/
HK Directory is: /data/data22/seq_proc/33012010.005/
 
!xsel:ASCA-SIS0-BRIGHT > read events ad33012010s000302m.evt
 
Getting Min and Max for Energy Column...
Got min and max for PI:     0   2047
 
Got the minimum time resolution of the read data:   4.0000
 Number of files read in:   2
 
******************** Observation Catalogue ********************
 
Data Directory is: /data/data22/seq_proc/33012010.005/
HK Directory is: /data/data22/seq_proc/33012010.005/
 
!xsel:ASCA-SIS0-BRIGHT > filter region ad33012010s032002_1.reg
!xsel:ASCA-SIS0-BRIGHT > extract events
!xsel:ASCA-SIS0-BRIGHT > save events outfile=events.tmp use_events=yes
Wrote events list to file events.tmp
Changing Data directory from:
    /data/data22/seq_proc/33012010.005/
to the current working directory.
!xsel:ASCA-SIS0-BRIGHT > exit save_session=no
-> Extracting ad33012010s000002_1.lc with binsize 360.411484885721
-> Standard Output From FTOOL xselect:
 
                         **  XSELECT V1.3   **
 
!> Enter session name >[xsel] xsel
 
 Notes: XSELECT set up for      ASCA
 Keywords for time and pha are  TIME       PI
 Units of time are              s
 Default timing binsize =    16.00
 Keywords for images are          DETX       DETY
 Keywords for the WMAP are        DETX       DETY
 
 
 
        OBJECT   DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME   NEVENTS  S0CCDPOW
      1 XY_ARI   BRIGHT   HIGH     29/01/96 17:30:23 0.46E+04      637 0100
 
EXTRACTOR vers 2.0  11 Apr 1997.
 Doing file: /data/data22/seq_proc/33012010.005/events.tmp
          Total      Good    Bad: Region      Time     Phase       Cut
            637       637              0         0         0         0
===============================================================================
   Grand Total      Good   Bad:  Region      Time     Phase       Cut
           637       637              0         0         0         0
   in    4591.64 seconds
 Fits light curve has      637 counts for 0.1387     counts/sec
 Command not found; type ? for a command listing
!xsel:ASCA > set mission ASCA
 
 Notes: XSELECT set up for      ASCA
 Keywords for time and pha are  TIME       PI
 Units of time are              s
 Default timing binsize =    16.00
 Keywords for images are          DETX       DETY
 Keywords for the WMAP are        DETX       DETY
 
!xsel:ASCA > set datadir .
 
Setting data directory to /data/data22/seq_proc/33012010.005/
Setting mkf directory to /data/data22/seq_proc/33012010.005/
 
!xsel:ASCA > read events events.tmp
Got new instrument: SIS0
 
Setting: IMAGE binning    =    4
         WMAP binning     =    8
         Energy Column    =  PI
         Energy rebinning =    1
 
 
Getting Min and Max for Energy Column...
Got min and max for PI:     0   2047
 
Got the minimum time resolution of the read data:   4.0000
 Number of files read in:   1
 
******************** Observation Catalogue ********************
 
Data Directory is: /data/data22/seq_proc/33012010.005/
HK Directory is: /data/data22/seq_proc/33012010.005/
 
!xsel:ASCA-SIS0-BRIGHT > set binsize 360.411484885721
!xsel:ASCA-SIS0-BRIGHT > extract curve exposure=0.5
!xsel:ASCA-SIS0-BRIGHT > save curve ad33012010s000002_1.lc
Wrote FITS light curve to file ad33012010s000002_1.lc
!xsel:ASCA-SIS0-BRIGHT > exit save_session=no
-> Plotting light curve ad33012010s000002_1_lc.ps
-> Standard Output From FTOOL xronos:

                                                     Type "help" for information


 [1]xronos>   Current User Interface is ;           command driven                          
 [2]xronos>       Enter up to  50 input filenames and options for series 1 (or rtn)    
      Ser. A filename   1 +options[.rbf]=> ad33012010s000002_1.lc                                                                                                              
 
 Selected FITS extensions: 1 - RATE TABLE;
 
 Source ............ XY_ARI              Start Time (d) .... 10111 18:13:23.239
 FITS Extension ....  1 - `RATE      `   Stop Time (d) ..... 10111 23:00:21.247
 No. of Rows .......           14        Bin Time (s) ......    360.4
 Right Ascension ... 4.4001E+01          Internal time sys.. Converted to TJD
 Declination ....... 1.9366E+01          Experiment ........ ASCA     SIS0
 
 Corrections applied: Vignetting - No ; Deadtime - No ; Bkgd - No ; Clock - No
 
 Selected Columns:   1 - Time;   2 - Y-axis;   3 - Y-error;
 
 File contains binned data.
 
      Ser. A filename   2 +options[.rbf]=>                                                                                                                                     
      Enter up to  50 input filenames and options for series 2 (or rtn)    
      Ser. B filename   1 +options[.rbf]=>                                                                                                                                     
      Enter up to  50 input filenames and options for series 3 (or rtn)    
      Ser. C filename   1 +options[.rbf]=>                                                                                                                                     
 [3]xronos> 
 Maximum of      1 Intvs. with        48 Newbins of       360.411     (s) 

 
 Intv    1   Start10111 18:16:23
     Ser.1     Avg 0.1368        Chisq  78.42       Var 0.2533E-02 Newbs.    14
               Min 0.1110E-01      Max 0.1918    expVar 0.4523E-03  Bins     14

             Results from Statistical Analysis

             Newbin Integration Time (s)..  360.41    
             Interval Duration (s)........  16939.    
             No. of Newbins ..............      14
             Average (c/s) ............... 0.13684      +/-    0.59E-02
             Standard Deviation (c/s)..... 0.50331E-01
             Minimum (c/s)................ 0.11098E-01
             Maximum (c/s)................ 0.19183    
             Variance ((c/s)**2).......... 0.25332E-02 +/-    0.99E-03
             Expected Variance ((c/s)**2). 0.45227E-03 +/-    0.18E-03
             Third Moment ((c/s)**3)......-0.20384E-03
             Average Deviation (c/s)...... 0.33795E-01
             Skewness..................... -1.5987        +/-    0.65    
             Kurtosis.....................  1.3884        +/-     1.3    
             RMS fractional variation..... 0.33336        +/-    0.80E-01
             Chi-Square...................  78.415        dof      13
             Chi-Square Prob of constancy. 0.21899E-10 (0 means < 1.e-38)
             Kolm.-Smir. Prob of constancy 0.32994E-05 (0 means < 1.e-38)

 [4]xronos>  [5]xronos> 
 Maximum of      1 Intvs. with        48 Newbins of       360.411     (s) 

 
 Intv    1   Start10111 18:16:23
     Ser.1     Avg 0.1368        Chisq  78.42       Var 0.2533E-02 Newbs.    14
               Min 0.1110E-01      Max 0.1918    expVar 0.4523E-03  Bins     14
             Light curve ready !
 Frme    1  Written to output file : xronos.qlc1                                                                                                                         
 PLT>  PLT>  PLT>  [6]xronos> 
-> TIMEDEL=4.0000000000E+00 for ad33012010s100102h.evt
-> TIMEDEL=4.0000000000E+00 for ad33012010s100302m.evt
-> Minimum bin size is 4.0000000000E+00 seconds
-> Extracting events from region ad33012010s132002_1.reg
-> ... and files: ad33012010s100102h.evt ad33012010s100302m.evt
-> Standard Output From FTOOL xselect:
 
                         **  XSELECT V1.3   **
 
!> Enter session name >[xsel] xsel
 
 Notes: XSELECT set up for      ASCA
 Keywords for time and pha are  TIME       PI
 Units of time are              s
 Default timing binsize =    16.00
 Keywords for images are          DETX       DETY
 Keywords for the WMAP are        DETX       DETY
 
 
 
        OBJECT   DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME   NEVENTS  S1CCDPOW
      1 XY_ARI   BRIGHT   HIGH     29/01/96 17:42:55 0.39E+04      628 0001
 
 
 
        OBJECT   DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME   NEVENTS  S1CCDPOW
      1 XY_ARI   BRIGHT   HIGH     29/01/96 17:42:55 0.39E+04      628 0001
      2 XY_ARI   BRIGHT   MEDIUM   29/01/96 17:30:23 0.79E+03      153 0001
 
EXTRACTOR vers 2.0  11 Apr 1997.
 Doing file: /data/data22/seq_proc/33012010.005/ad33012010s100102h.evt
          Total      Good    Bad: Region      Time     Phase       Cut
            628       507            121         0         0         0
 Writing events file
    507 events written to the output file
 Doing file: /data/data22/seq_proc/33012010.005/ad33012010s100302m.evt
          Total      Good    Bad: Region      Time     Phase       Cut
            153       127             26         0         0         0
 Writing events file
    634 events written to the output file
===============================================================================
   Grand Total      Good   Bad:  Region      Time     Phase       Cut
           781       634            147         0         0         0
   in    4729.61 seconds
 Command not found; type ? for a command listing
!xsel:ASCA > set mission ASCA
 
 Notes: XSELECT set up for      ASCA
 Keywords for time and pha are  TIME       PI
 Units of time are              s
 Default timing binsize =    16.00
 Keywords for images are          DETX       DETY
 Keywords for the WMAP are        DETX       DETY
 
!xsel:ASCA > set datadir .
 
Setting data directory to /data/data22/seq_proc/33012010.005/
Setting mkf directory to /data/data22/seq_proc/33012010.005/
 
!xsel:ASCA > read events ad33012010s100102h.evt
Got new instrument: SIS1
 
Setting: IMAGE binning    =    4
         WMAP binning     =    8
         Energy Column    =  PI
         Energy rebinning =    1
 
 
Getting Min and Max for Energy Column...
Got min and max for PI:     0   2047
 
Got the minimum time resolution of the read data:   4.0000
 Number of files read in:   1
 
******************** Observation Catalogue ********************
 
Data Directory is: /data/data22/seq_proc/33012010.005/
HK Directory is: /data/data22/seq_proc/33012010.005/
 
!xsel:ASCA-SIS1-BRIGHT > read events ad33012010s100302m.evt
 
Getting Min and Max for Energy Column...
Got min and max for PI:     0   2047
 
Got the minimum time resolution of the read data:   4.0000
 Number of files read in:   2
 
******************** Observation Catalogue ********************
 
Data Directory is: /data/data22/seq_proc/33012010.005/
HK Directory is: /data/data22/seq_proc/33012010.005/
 
!xsel:ASCA-SIS1-BRIGHT > filter region ad33012010s132002_1.reg
!xsel:ASCA-SIS1-BRIGHT > extract events
!xsel:ASCA-SIS1-BRIGHT > save events outfile=events.tmp use_events=yes
Wrote events list to file events.tmp
Changing Data directory from:
    /data/data22/seq_proc/33012010.005/
to the current working directory.
!xsel:ASCA-SIS1-BRIGHT > exit save_session=no
-> Extracting ad33012010s100002_1.lc with binsize 372.997717790846
-> Standard Output From FTOOL xselect:
 
                         **  XSELECT V1.3   **
 
!> Enter session name >[xsel] xsel
 
 Notes: XSELECT set up for      ASCA
 Keywords for time and pha are  TIME       PI
 Units of time are              s
 Default timing binsize =    16.00
 Keywords for images are          DETX       DETY
 Keywords for the WMAP are        DETX       DETY
 
 
 
        OBJECT   DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME   NEVENTS  S1CCDPOW
      1 XY_ARI   BRIGHT   HIGH     29/01/96 17:30:23 0.47E+04      634 0001
 
EXTRACTOR vers 2.0  11 Apr 1997.
 Doing file: /data/data22/seq_proc/33012010.005/events.tmp
          Total      Good    Bad: Region      Time     Phase       Cut
            634       634              0         0         0         0
===============================================================================
   Grand Total      Good   Bad:  Region      Time     Phase       Cut
           634       634              0         0         0         0
   in    4729.61 seconds
 Fits light curve has      634 counts for 0.1340     counts/sec
 Command not found; type ? for a command listing
!xsel:ASCA > set mission ASCA
 
 Notes: XSELECT set up for      ASCA
 Keywords for time and pha are  TIME       PI
 Units of time are              s
 Default timing binsize =    16.00
 Keywords for images are          DETX       DETY
 Keywords for the WMAP are        DETX       DETY
 
!xsel:ASCA > set datadir .
 
Setting data directory to /data/data22/seq_proc/33012010.005/
Setting mkf directory to /data/data22/seq_proc/33012010.005/
 
!xsel:ASCA > read events events.tmp
Got new instrument: SIS1
 
Setting: IMAGE binning    =    4
         WMAP binning     =    8
         Energy Column    =  PI
         Energy rebinning =    1
 
 
Getting Min and Max for Energy Column...
Got min and max for PI:     0   2047
 
Got the minimum time resolution of the read data:   4.0000
 Number of files read in:   1
 
******************** Observation Catalogue ********************
 
Data Directory is: /data/data22/seq_proc/33012010.005/
HK Directory is: /data/data22/seq_proc/33012010.005/
 
!xsel:ASCA-SIS1-BRIGHT > set binsize 372.997717790846
!xsel:ASCA-SIS1-BRIGHT > extract curve exposure=0.5
!xsel:ASCA-SIS1-BRIGHT > save curve ad33012010s100002_1.lc
Wrote FITS light curve to file ad33012010s100002_1.lc
!xsel:ASCA-SIS1-BRIGHT > exit save_session=no
-> Plotting light curve ad33012010s100002_1_lc.ps
-> Standard Output From FTOOL xronos:

                                                     Type "help" for information


 [1]xronos>   Current User Interface is ;           command driven                          
 [2]xronos>       Enter up to  50 input filenames and options for series 1 (or rtn)    
      Ser. A filename   1 +options[.rbf]=> ad33012010s100002_1.lc                                                                                                              
 
 Selected FITS extensions: 1 - RATE TABLE;
 
 Source ............ XY_ARI              Start Time (d) .... 10111 18:13:15.239
 FITS Extension ....  1 - `RATE      `   Stop Time (d) ..... 10111 23:00:21.247
 No. of Rows .......           14        Bin Time (s) ......    373.0
 Right Ascension ... 4.4001E+01          Internal time sys.. Converted to TJD
 Declination ....... 1.9366E+01          Experiment ........ ASCA     SIS1
 
 Corrections applied: Vignetting - No ; Deadtime - No ; Bkgd - No ; Clock - No
 
 Selected Columns:   1 - Time;   2 - Y-axis;   3 - Y-error;
 
 File contains binned data.
 
      Ser. A filename   2 +options[.rbf]=>                                                                                                                                     
      Enter up to  50 input filenames and options for series 2 (or rtn)    
      Ser. B filename   1 +options[.rbf]=>                                                                                                                                     
      Enter up to  50 input filenames and options for series 3 (or rtn)    
      Ser. C filename   1 +options[.rbf]=>                                                                                                                                     
 [3]xronos> 
 Maximum of      1 Intvs. with        47 Newbins of       372.998     (s) 

 
 Intv    1   Start10111 18:16:21
     Ser.1     Avg 0.1352        Chisq  70.98       Var 0.2206E-02 Newbs.    14
               Min 0.1877E-01      Max 0.2011    expVar 0.4352E-03  Bins     14

             Results from Statistical Analysis

             Newbin Integration Time (s)..  373.00    
             Interval Duration (s)........  16785.    
             No. of Newbins ..............      14
             Average (c/s) ............... 0.13524      +/-    0.58E-02
             Standard Deviation (c/s)..... 0.46973E-01
             Minimum (c/s)................ 0.18767E-01
             Maximum (c/s)................ 0.20107    
             Variance ((c/s)**2).......... 0.22064E-02 +/-    0.87E-03
             Expected Variance ((c/s)**2). 0.43517E-03 +/-    0.17E-03
             Third Moment ((c/s)**3)......-0.11040E-03
             Average Deviation (c/s)...... 0.36719E-01
             Skewness..................... -1.0652        +/-    0.65    
             Kurtosis..................... 0.58072        +/-     1.3    
             RMS fractional variation..... 0.31120        +/-    0.76E-01
             Chi-Square...................  70.984        dof      13
             Chi-Square Prob of constancy. 0.52876E-09 (0 means < 1.e-38)
             Kolm.-Smir. Prob of constancy 0.10154E-04 (0 means < 1.e-38)

 [4]xronos>  [5]xronos> 
 Maximum of      1 Intvs. with        47 Newbins of       372.998     (s) 

 
 Intv    1   Start10111 18:16:21
     Ser.1     Avg 0.1352        Chisq  70.98       Var 0.2206E-02 Newbs.    14
               Min 0.1877E-01      Max 0.2011    expVar 0.4352E-03  Bins     14
             Light curve ready !
 Frme    1  Written to output file : xronos.qlc1                                                                                                                         
 PLT>  PLT>  PLT>  [6]xronos> 
-> TIMEDEL=6.2500000000E-02 for ad33012010g200170h.evt
-> TIMEDEL=2.0000000000E+00 for ad33012010g200270l.evt
-> TIMEDEL=5.0000000000E-01 for ad33012010g200370m.evt
-> Minimum bin size is 2.0000000000E+00 seconds
-> Extracting events from region ad33012010g225670_1.reg
-> ... and files: ad33012010g200170h.evt ad33012010g200270l.evt ad33012010g200370m.evt
-> Standard Output From FTOOL xselect:
 
                         **  XSELECT V1.3   **
 
!> Enter session name >[xsel] xsel
 
 Notes: XSELECT set up for      ASCA
 Keywords for time and pha are  TIME       PI
 Units of time are              s
 Default timing binsize =    16.00
 Keywords for images are          DETX       DETY
 Keywords for the WMAP are        DETX       DETY
 
 
 
        OBJECT   DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME   NEVENTS  PHA_BINS
      1 XY_ARI   PH       HIGH     29/01/96 17:43:01 0.38E+04     1358     1024
 
 
 
        OBJECT   DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME   NEVENTS  PHA_BINS
      1 XY_ARI   PH       HIGH     29/01/96 17:43:01 0.38E+04     1358     1024
      2 XY_ARI   PH       LOW      29/01/96 18:46:29 0.32E+02       16     1024
 
 
 
        OBJECT   DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME   NEVENTS  PHA_BINS
      1 XY_ARI   PH       HIGH     29/01/96 17:43:01 0.38E+04     1358     1024
      2 XY_ARI   PH       LOW      29/01/96 18:46:29 0.32E+02       16     1024
      3 XY_ARI   PH       MEDIUM   29/01/96 17:30:29 0.13E+04      547     1024
 
EXTRACTOR vers 2.0  11 Apr 1997.
 Doing file: /data/data22/seq_proc/33012010.005/ad33012010g200170h.evt
          Total      Good    Bad: Region      Time     Phase       Cut
           1358       450            908         0         0         0
 Writing events file
    450 events written to the output file
 Doing file: /data/data22/seq_proc/33012010.005/ad33012010g200270l.evt
          Total      Good    Bad: Region      Time     Phase       Cut
             16         7              9         0         0         0
 Writing events file
    457 events written to the output file
 Doing file: /data/data22/seq_proc/33012010.005/ad33012010g200370m.evt
          Total      Good    Bad: Region      Time     Phase       Cut
            547       193            354         0         0         0
 Writing events file
    650 events written to the output file
===============================================================================
   Grand Total      Good   Bad:  Region      Time     Phase       Cut
          1921       650           1271         0         0         0
   in    5190.01 seconds
 Command not found; type ? for a command listing
!xsel:ASCA > set mission ASCA
 
 Notes: XSELECT set up for      ASCA
 Keywords for time and pha are  TIME       PI
 Units of time are              s
 Default timing binsize =    16.00
 Keywords for images are          DETX       DETY
 Keywords for the WMAP are        DETX       DETY
 
!xsel:ASCA > set datadir .
 
Setting data directory to /data/data22/seq_proc/33012010.005/
Setting mkf directory to /data/data22/seq_proc/33012010.005/
 
!xsel:ASCA > read events ad33012010g200170h.evt
Got new instrument: GIS2
 
Setting: IMAGE binning    =    1
         WMAP binning     =    1
         Energy Column    =  PI
         Energy rebinning =    1
 
 
Getting Min and Max for Energy Column...
Got min and max for PI:     0   1023
 
Got the minimum time resolution of the read data:  0.62500E-01
 Number of files read in:   1
 
******************** Observation Catalogue ********************
 
Data Directory is: /data/data22/seq_proc/33012010.005/
HK Directory is: /data/data22/seq_proc/33012010.005/
 
!xsel:ASCA-GIS2-PH > read events ad33012010g200270l.evt
 
Getting Min and Max for Energy Column...
Got min and max for PI:     0   1023
 
Got the minimum time resolution of the read data:   2.0000
 Number of files read in:   2
 
******************** Observation Catalogue ********************
 
Data Directory is: /data/data22/seq_proc/33012010.005/
HK Directory is: /data/data22/seq_proc/33012010.005/
 
!xsel:ASCA-GIS2-PH > read events ad33012010g200370m.evt
 
Getting Min and Max for Energy Column...
Got min and max for PI:     0   1023
 
Got the minimum time resolution of the read data:  0.50000
 Number of files read in:   3
 
******************** Observation Catalogue ********************
 
Data Directory is: /data/data22/seq_proc/33012010.005/
HK Directory is: /data/data22/seq_proc/33012010.005/
 
!xsel:ASCA-GIS2-PH > filter region ad33012010g225670_1.reg
!xsel:ASCA-GIS2-PH > extract events
!xsel:ASCA-GIS2-PH > save events outfile=events.tmp use_events=yes
Wrote events list to file events.tmp
Changing Data directory from:
    /data/data22/seq_proc/33012010.005/
to the current working directory.
!xsel:ASCA-GIS2-PH > exit save_session=no
-> Extracting ad33012010g200070_1.lc with binsize 399.231573720391
-> Standard Output From FTOOL xselect:
 
                         **  XSELECT V1.3   **
 
!> Enter session name >[xsel] xsel
 
 Notes: XSELECT set up for      ASCA
 Keywords for time and pha are  TIME       PI
 Units of time are              s
 Default timing binsize =    16.00
 Keywords for images are          DETX       DETY
 Keywords for the WMAP are        DETX       DETY
 
 
 
        OBJECT   DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME   NEVENTS  PHA_BINS
      1 XY_ARI   PH       HIGH     29/01/96 17:30:29 0.52E+04      650     1024
 
EXTRACTOR vers 2.0  11 Apr 1997.
 Doing file: /data/data22/seq_proc/33012010.005/events.tmp
          Total      Good    Bad: Region      Time     Phase       Cut
            650       650              0         0         0         0
===============================================================================
   Grand Total      Good   Bad:  Region      Time     Phase       Cut
           650       650              0         0         0         0
   in    5190.01 seconds
 Fits light curve has      650 counts for 0.1252     counts/sec
 Command not found; type ? for a command listing
!xsel:ASCA > set mission ASCA
 
 Notes: XSELECT set up for      ASCA
 Keywords for time and pha are  TIME       PI
 Units of time are              s
 Default timing binsize =    16.00
 Keywords for images are          DETX       DETY
 Keywords for the WMAP are        DETX       DETY
 
!xsel:ASCA > set datadir .
 
Setting data directory to /data/data22/seq_proc/33012010.005/
Setting mkf directory to /data/data22/seq_proc/33012010.005/
 
!xsel:ASCA > read events events.tmp
Got new instrument: GIS2
 
Setting: IMAGE binning    =    1
         WMAP binning     =    1
         Energy Column    =  PI
         Energy rebinning =    1
 
 
Getting Min and Max for Energy Column...
Got min and max for PI:     0   1023
 
Got the minimum time resolution of the read data:  0.62500E-01
 Number of files read in:   1
 
******************** Observation Catalogue ********************
 
Data Directory is: /data/data22/seq_proc/33012010.005/
HK Directory is: /data/data22/seq_proc/33012010.005/
 
!xsel:ASCA-GIS2-PH > set binsize 399.231573720391
!xsel:ASCA-GIS2-PH > extract curve exposure=0.5
!xsel:ASCA-GIS2-PH > save curve ad33012010g200070_1.lc
Wrote FITS light curve to file ad33012010g200070_1.lc
!xsel:ASCA-GIS2-PH > exit save_session=no
-> Plotting light curve ad33012010g200070_1_lc.ps
-> Standard Output From FTOOL xronos:

                                                     Type "help" for information


 [1]xronos>   Current User Interface is ;           command driven                          
 [2]xronos>       Enter up to  50 input filenames and options for series 1 (or rtn)    
      Ser. A filename   1 +options[.rbf]=> ad33012010g200070_1.lc                                                                                                              
 
 Selected FITS extensions: 1 - RATE TABLE;
 
 Source ............ XY_ARI              Start Time (d) .... 10111 17:45:41.247
 FITS Extension ....  1 - `RATE      `   Stop Time (d) ..... 10111 23:00:21.247
 No. of Rows .......           13        Bin Time (s) ......    399.2
 Right Ascension ... 4.4001E+01          Internal time sys.. Converted to TJD
 Declination ....... 1.9366E+01          Experiment ........ ASCA     GIS2
 
 Corrections applied: Vignetting - No ; Deadtime - No ; Bkgd - No ; Clock - No
 
 Selected Columns:   1 - Time;   2 - Y-axis;   3 - Y-error;
 
 File contains binned data.
 
      Ser. A filename   2 +options[.rbf]=>                                                                                                                                     
      Enter up to  50 input filenames and options for series 2 (or rtn)    
      Ser. B filename   1 +options[.rbf]=>                                                                                                                                     
      Enter up to  50 input filenames and options for series 3 (or rtn)    
      Ser. C filename   1 +options[.rbf]=>                                                                                                                                     
 [3]xronos> 
 Maximum of      1 Intvs. with        48 Newbins of       399.232     (s) 

 
 Intv    1   Start10111 18:15:37
     Ser.1     Avg 0.1216        Chisq  74.99       Var 0.2112E-02 Newbs.    13
               Min 0.2343E-01      Max 0.1707    expVar 0.3662E-03  Bins     13

             Results from Statistical Analysis

             Newbin Integration Time (s)..  399.23    
             Interval Duration (s)........  16768.    
             No. of Newbins ..............      13
             Average (c/s) ............... 0.12158      +/-    0.55E-02
             Standard Deviation (c/s)..... 0.45961E-01
             Minimum (c/s)................ 0.23432E-01
             Maximum (c/s)................ 0.17070    
             Variance ((c/s)**2).......... 0.21124E-02 +/-    0.86E-03
             Expected Variance ((c/s)**2). 0.36622E-03 +/-    0.15E-03
             Third Moment ((c/s)**3)......-0.10572E-03
             Average Deviation (c/s)...... 0.35265E-01
             Skewness..................... -1.0889        +/-    0.68    
             Kurtosis..................... 0.80340E-01    +/-     1.4    
             RMS fractional variation..... 0.34369        +/-    0.85E-01
             Chi-Square...................  74.986        dof      12
             Chi-Square Prob of constancy. 0.36978E-10 (0 means < 1.e-38)
             Kolm.-Smir. Prob of constancy 0.15669E-09 (0 means < 1.e-38)

 [4]xronos>  [5]xronos> 
 Maximum of      1 Intvs. with        48 Newbins of       399.232     (s) 

 
 Intv    1   Start10111 18:15:37
     Ser.1     Avg 0.1216        Chisq  74.99       Var 0.2112E-02 Newbs.    13
               Min 0.2343E-01      Max 0.1707    expVar 0.3662E-03  Bins     13
             Light curve ready !
 Frme    1  Written to output file : xronos.qlc1                                                                                                                         
 PLT>  PLT>  PLT>  [6]xronos> 
-> TIMEDEL=6.2500000000E-02 for ad33012010g300170h.evt
-> TIMEDEL=2.0000000000E+00 for ad33012010g300270l.evt
-> TIMEDEL=5.0000000000E-01 for ad33012010g300370m.evt
-> Minimum bin size is 2.0000000000E+00 seconds
-> Extracting events from region ad33012010g325670_1.reg
-> ... and files: ad33012010g300170h.evt ad33012010g300270l.evt ad33012010g300370m.evt
-> Standard Output From FTOOL xselect:
 
                         **  XSELECT V1.3   **
 
!> Enter session name >[xsel] xsel
 
 Notes: XSELECT set up for      ASCA
 Keywords for time and pha are  TIME       PI
 Units of time are              s
 Default timing binsize =    16.00
 Keywords for images are          DETX       DETY
 Keywords for the WMAP are        DETX       DETY
 
 
 
        OBJECT   DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME   NEVENTS  PHA_BINS
      1 XY_ARI   PH       HIGH     29/01/96 17:43:01 0.38E+04     1552     1024
 
 
 
        OBJECT   DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME   NEVENTS  PHA_BINS
      1 XY_ARI   PH       HIGH     29/01/96 17:43:01 0.38E+04     1552     1024
      2 XY_ARI   PH       LOW      29/01/96 18:46:29 0.32E+02       18     1024
 
 
 
        OBJECT   DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME   NEVENTS  PHA_BINS
      1 XY_ARI   PH       HIGH     29/01/96 17:43:01 0.38E+04     1552     1024
      2 XY_ARI   PH       LOW      29/01/96 18:46:29 0.32E+02       18     1024
      3 XY_ARI   PH       MEDIUM   29/01/96 17:30:29 0.13E+04      623     1024
 
EXTRACTOR vers 2.0  11 Apr 1997.
 Doing file: /data/data22/seq_proc/33012010.005/ad33012010g300170h.evt
          Total      Good    Bad: Region      Time     Phase       Cut
           1552       563            989         0         0         0
 Writing events file
    563 events written to the output file
 Doing file: /data/data22/seq_proc/33012010.005/ad33012010g300270l.evt
          Total      Good    Bad: Region      Time     Phase       Cut
             18        10              8         0         0         0
 Writing events file
    573 events written to the output file
 Doing file: /data/data22/seq_proc/33012010.005/ad33012010g300370m.evt
          Total      Good    Bad: Region      Time     Phase       Cut
            623       244            379         0         0         0
 Writing events file
    817 events written to the output file
===============================================================================
   Grand Total      Good   Bad:  Region      Time     Phase       Cut
          2193       817           1376         0         0         0
   in    5187.97 seconds
 Command not found; type ? for a command listing
!xsel:ASCA > set mission ASCA
 
 Notes: XSELECT set up for      ASCA
 Keywords for time and pha are  TIME       PI
 Units of time are              s
 Default timing binsize =    16.00
 Keywords for images are          DETX       DETY
 Keywords for the WMAP are        DETX       DETY
 
!xsel:ASCA > set datadir .
 
Setting data directory to /data/data22/seq_proc/33012010.005/
Setting mkf directory to /data/data22/seq_proc/33012010.005/
 
!xsel:ASCA > read events ad33012010g300170h.evt
Got new instrument: GIS3
 
Setting: IMAGE binning    =    1
         WMAP binning     =    1
         Energy Column    =  PI
         Energy rebinning =    1
 
 
Getting Min and Max for Energy Column...
Got min and max for PI:     0   1023
 
Got the minimum time resolution of the read data:  0.62500E-01
 Number of files read in:   1
 
******************** Observation Catalogue ********************
 
Data Directory is: /data/data22/seq_proc/33012010.005/
HK Directory is: /data/data22/seq_proc/33012010.005/
 
!xsel:ASCA-GIS3-PH > read events ad33012010g300270l.evt
 
Getting Min and Max for Energy Column...
Got min and max for PI:     0   1023
 
Got the minimum time resolution of the read data:   2.0000
 Number of files read in:   2
 
******************** Observation Catalogue ********************
 
Data Directory is: /data/data22/seq_proc/33012010.005/
HK Directory is: /data/data22/seq_proc/33012010.005/
 
!xsel:ASCA-GIS3-PH > read events ad33012010g300370m.evt
 
Getting Min and Max for Energy Column...
Got min and max for PI:     0   1023
 
Got the minimum time resolution of the read data:  0.50000
 Number of files read in:   3
 
******************** Observation Catalogue ********************
 
Data Directory is: /data/data22/seq_proc/33012010.005/
HK Directory is: /data/data22/seq_proc/33012010.005/
 
!xsel:ASCA-GIS3-PH > filter region ad33012010g325670_1.reg
!xsel:ASCA-GIS3-PH > extract events
!xsel:ASCA-GIS3-PH > save events outfile=events.tmp use_events=yes
Wrote events list to file events.tmp
Changing Data directory from:
    /data/data22/seq_proc/33012010.005/
to the current working directory.
!xsel:ASCA-GIS3-PH > exit save_session=no
-> Extracting ad33012010g300070_1.lc with binsize 317.501200231264
-> Standard Output From FTOOL xselect:
 
                         **  XSELECT V1.3   **
 
!> Enter session name >[xsel] xsel
 
 Notes: XSELECT set up for      ASCA
 Keywords for time and pha are  TIME       PI
 Units of time are              s
 Default timing binsize =    16.00
 Keywords for images are          DETX       DETY
 Keywords for the WMAP are        DETX       DETY
 
 
 
        OBJECT   DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME   NEVENTS  PHA_BINS
      1 XY_ARI   PH       HIGH     29/01/96 17:30:29 0.52E+04      817     1024
 
EXTRACTOR vers 2.0  11 Apr 1997.
 Doing file: /data/data22/seq_proc/33012010.005/events.tmp
          Total      Good    Bad: Region      Time     Phase       Cut
            817       817              0         0         0         0
===============================================================================
   Grand Total      Good   Bad:  Region      Time     Phase       Cut
           817       817              0         0         0         0
   in    5187.97 seconds
 Fits light curve has      817 counts for 0.1575     counts/sec
 Command not found; type ? for a command listing
!xsel:ASCA > set mission ASCA
 
 Notes: XSELECT set up for      ASCA
 Keywords for time and pha are  TIME       PI
 Units of time are              s
 Default timing binsize =    16.00
 Keywords for images are          DETX       DETY
 Keywords for the WMAP are        DETX       DETY
 
!xsel:ASCA > set datadir .
 
Setting data directory to /data/data22/seq_proc/33012010.005/
Setting mkf directory to /data/data22/seq_proc/33012010.005/
 
!xsel:ASCA > read events events.tmp
Got new instrument: GIS3
 
Setting: IMAGE binning    =    1
         WMAP binning     =    1
         Energy Column    =  PI
         Energy rebinning =    1
 
 
Getting Min and Max for Energy Column...
Got min and max for PI:     0   1023
 
Got the minimum time resolution of the read data:  0.62500E-01
 Number of files read in:   1
 
******************** Observation Catalogue ********************
 
Data Directory is: /data/data22/seq_proc/33012010.005/
HK Directory is: /data/data22/seq_proc/33012010.005/
 
!xsel:ASCA-GIS3-PH > set binsize 317.501200231264
!xsel:ASCA-GIS3-PH > extract curve exposure=0.5
!xsel:ASCA-GIS3-PH > save curve ad33012010g300070_1.lc
Wrote FITS light curve to file ad33012010g300070_1.lc
!xsel:ASCA-GIS3-PH > exit save_session=no
-> Plotting light curve ad33012010g300070_1_lc.ps
-> Standard Output From FTOOL xronos:

                                                     Type "help" for information


 [1]xronos>   Current User Interface is ;           command driven                          
 [2]xronos>       Enter up to  50 input filenames and options for series 1 (or rtn)    
      Ser. A filename   1 +options[.rbf]=> ad33012010g300070_1.lc                                                                                                              
 
 Selected FITS extensions: 1 - RATE TABLE;
 
 Source ............ XY_ARI              Start Time (d) .... 10111 17:45:41.247
 FITS Extension ....  1 - `RATE      `   Stop Time (d) ..... 10111 23:00:21.247
 No. of Rows .......           16        Bin Time (s) ......    317.5
 Right Ascension ... 4.4001E+01          Internal time sys.. Converted to TJD
 Declination ....... 1.9366E+01          Experiment ........ ASCA     GIS3
 
 Corrections applied: Vignetting - No ; Deadtime - No ; Bkgd - No ; Clock - No
 
 Selected Columns:   1 - Time;   2 - Y-axis;   3 - Y-error;
 
 File contains binned data.
 
      Ser. A filename   2 +options[.rbf]=>                                                                                                                                     
      Enter up to  50 input filenames and options for series 2 (or rtn)    
      Ser. B filename   1 +options[.rbf]=>                                                                                                                                     
      Enter up to  50 input filenames and options for series 3 (or rtn)    
      Ser. C filename   1 +options[.rbf]=>                                                                                                                                     
 [3]xronos> 
 Maximum of      1 Intvs. with        60 Newbins of       317.501     (s) 

 
 Intv    1   Start10111 18:14:47
     Ser.1     Avg 0.1619        Chisq  72.49       Var 0.2625E-02 Newbs.    16
               Min 0.2520E-01      Max 0.2144    expVar 0.5794E-03  Bins     16

             Results from Statistical Analysis

             Newbin Integration Time (s)..  317.50    
             Interval Duration (s)........  16828.    
             No. of Newbins ..............      16
             Average (c/s) ............... 0.16187      +/-    0.62E-02
             Standard Deviation (c/s)..... 0.51236E-01
             Minimum (c/s)................ 0.25197E-01
             Maximum (c/s)................ 0.21444    
             Variance ((c/s)**2).......... 0.26251E-02 +/-    0.96E-03
             Expected Variance ((c/s)**2). 0.57942E-03 +/-    0.21E-03
             Third Moment ((c/s)**3)......-0.18623E-03
             Average Deviation (c/s)...... 0.39246E-01
             Skewness..................... -1.3846        +/-    0.61    
             Kurtosis.....................  1.1501        +/-     1.2    
             RMS fractional variation..... 0.27941        +/-    0.65E-01
             Chi-Square...................  72.489        dof      15
             Chi-Square Prob of constancy. 0.16037E-08 (0 means < 1.e-38)
             Kolm.-Smir. Prob of constancy 0.10960E-03 (0 means < 1.e-38)

 [4]xronos>  [5]xronos> 
 Maximum of      1 Intvs. with        60 Newbins of       317.501     (s) 

 
 Intv    1   Start10111 18:14:47
     Ser.1     Avg 0.1619        Chisq  72.49       Var 0.2625E-02 Newbs.    16
               Min 0.2520E-01      Max 0.2144    expVar 0.5794E-03  Bins     16
             Light curve ready !
 Frme    1  Written to output file : xronos.qlc1                                                                                                                         
 PLT>  PLT>  PLT>  [6]xronos> 
-> Merging GTIs from the following files:
ad33012010g200170h.evt[2]
ad33012010g200270l.evt[2]
ad33012010g200370m.evt[2]
-> Making L1 light curve of ft960129_1730_2300G2HK.fits with irate=HIGH
-> Standard Output From FTOOL ghkcurve:
ghkcurve: ALLGTI found in input HK file, will be applied to data.
ghkcurve:   8493 output records from    8503  good input G2_L1    records.
-> Making L1 light curve of ft960129_1730_2300G2HK.fits with irate=HI+MED
-> Standard Output From FTOOL ghkcurve:
ghkcurve: ALLGTI found in input HK file, will be applied to data.
ghkcurve:   4777 output records from    9766  good input G2_L1    records.
-> Merging GTIs from the following files:
ad33012010g300170h.evt[2]
ad33012010g300270l.evt[2]
ad33012010g300370m.evt[2]
-> Making L1 light curve of ft960129_1730_2300G3HK.fits with irate=HIGH
-> Standard Output From FTOOL ghkcurve:
ghkcurve: ALLGTI found in input HK file, will be applied to data.
ghkcurve:   8165 output records from    8176  good input G3_L1    records.
-> Making L1 light curve of ft960129_1730_2300G3HK.fits with irate=HI+MED
-> Standard Output From FTOOL ghkcurve:
ghkcurve: ALLGTI found in input HK file, will be applied to data.
ghkcurve:   4704 output records from    9421  good input G3_L1    records.

Extracting source event files ( 15:26:49 )

-> Extracting unbinned light curve ad33012010g200170h_1.ulc
-> Standard Output From FTOOL xselect:
 
                         **  XSELECT V1.3   **
 
!> Enter session name >[xsel] xsel
 
 Notes: XSELECT set up for      ASCA
 Keywords for time and pha are  TIME       PI
 Units of time are              s
 Default timing binsize =    16.00
 Keywords for images are          DETX       DETY
 Keywords for the WMAP are        DETX       DETY
 
 
 
        OBJECT   DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME   NEVENTS  PHA_BINS
      1 XY_ARI   PH       HIGH     29/01/96 17:43:01 0.38E+04     1358     1024
 
EXTRACTOR vers 2.0  11 Apr 1997.
 Doing file: /data/data22/seq_proc/33012010.005/ad33012010g200170h.evt
          Total      Good    Bad: Region      Time     Phase       Cut
           1358       450            908         0         0         0
 Writing events file
    450 events written to the output file
===============================================================================
   Grand Total      Good   Bad:  Region      Time     Phase       Cut
          1358       450            908         0         0         0
   in    3814.01 seconds
 Command not found; type ? for a command listing
!xsel:ASCA > set mission ASCA
 
 Notes: XSELECT set up for      ASCA
 Keywords for time and pha are  TIME       PI
 Units of time are              s
 Default timing binsize =    16.00
 Keywords for images are          DETX       DETY
 Keywords for the WMAP are        DETX       DETY
 
!xsel:ASCA > set datadir .
 
Setting data directory to /data/data22/seq_proc/33012010.005/
Setting mkf directory to /data/data22/seq_proc/33012010.005/
 
!xsel:ASCA > read events ad33012010g200170h.evt
Got new instrument: GIS2
 
Setting: IMAGE binning    =    1
         WMAP binning     =    1
         Energy Column    =  PI
         Energy rebinning =    1
 
 
Getting Min and Max for Energy Column...
Got min and max for PI:     0   1023
 
Got the minimum time resolution of the read data:  0.62500E-01
 Number of files read in:   1
 
******************** Observation Catalogue ********************
 
Data Directory is: /data/data22/seq_proc/33012010.005/
HK Directory is: /data/data22/seq_proc/33012010.005/
 
!xsel:ASCA-GIS2-PH > filter region ad33012010g225670_1.reg
!xsel:ASCA-GIS2-PH > extract events
!xsel:ASCA-GIS2-PH > save events outfile=ad33012010g200170h_1.ulc use_events=yes
Wrote events list to file ad33012010g200170h_1.ulc
Changing Data directory from:
    /data/data22/seq_proc/33012010.005/
to the current working directory.
!xsel:ASCA-GIS2-PH > exit save_session=no
-> Extracting unbinned light curve ad33012010g200270l_1.ulc
-> Standard Output From FTOOL xselect:
 
                         **  XSELECT V1.3   **
 
!> Enter session name >[xsel] xsel
 
 Notes: XSELECT set up for      ASCA
 Keywords for time and pha are  TIME       PI
 Units of time are              s
 Default timing binsize =    16.00
 Keywords for images are          DETX       DETY
 Keywords for the WMAP are        DETX       DETY
 
 
 
        OBJECT   DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME   NEVENTS  PHA_BINS
      1 XY_ARI   PH       LOW      29/01/96 18:46:29 0.32E+02       16     1024
 
EXTRACTOR vers 2.0  11 Apr 1997.
 Doing file: /data/data22/seq_proc/33012010.005/ad33012010g200270l.evt
          Total      Good    Bad: Region      Time     Phase       Cut
             16         7              9         0         0         0
 Writing events file
      7 events written to the output file
===============================================================================
   Grand Total      Good   Bad:  Region      Time     Phase       Cut
            16         7              9         0         0         0
   in      31.96 seconds
 Command not found; type ? for a command listing
!xsel:ASCA > set mission ASCA
 
 Notes: XSELECT set up for      ASCA
 Keywords for time and pha are  TIME       PI
 Units of time are              s
 Default timing binsize =    16.00
 Keywords for images are          DETX       DETY
 Keywords for the WMAP are        DETX       DETY
 
!xsel:ASCA > set datadir .
 
Setting data directory to /data/data22/seq_proc/33012010.005/
Setting mkf directory to /data/data22/seq_proc/33012010.005/
 
!xsel:ASCA > read events ad33012010g200270l.evt
Got new instrument: GIS2
 
Setting: IMAGE binning    =    1
         WMAP binning     =    1
         Energy Column    =  PI
         Energy rebinning =    1
 
 
Getting Min and Max for Energy Column...
Got min and max for PI:     0   1023
 
Got the minimum time resolution of the read data:   2.0000
 Number of files read in:   1
 
******************** Observation Catalogue ********************
 
Data Directory is: /data/data22/seq_proc/33012010.005/
HK Directory is: /data/data22/seq_proc/33012010.005/
 
!xsel:ASCA-GIS2-PH > filter region ad33012010g225670_1.reg
!xsel:ASCA-GIS2-PH > extract events
!xsel:ASCA-GIS2-PH > save events outfile=ad33012010g200270l_1.ulc use_events=yes
Wrote events list to file ad33012010g200270l_1.ulc
Changing Data directory from:
    /data/data22/seq_proc/33012010.005/
to the current working directory.
!xsel:ASCA-GIS2-PH > exit save_session=no
-> Deleting ad33012010g200270l_1.ulc since it has 7 events
-> Extracting unbinned light curve ad33012010g200370m_1.ulc
-> Standard Output From FTOOL xselect:
 
                         **  XSELECT V1.3   **
 
!> Enter session name >[xsel] xsel
 
 Notes: XSELECT set up for      ASCA
 Keywords for time and pha are  TIME       PI
 Units of time are              s
 Default timing binsize =    16.00
 Keywords for images are          DETX       DETY
 Keywords for the WMAP are        DETX       DETY
 
 
 
        OBJECT   DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME   NEVENTS  PHA_BINS
      1 XY_ARI   PH       MEDIUM   29/01/96 17:30:29 0.13E+04      547     1024
 
EXTRACTOR vers 2.0  11 Apr 1997.
 Doing file: /data/data22/seq_proc/33012010.005/ad33012010g200370m.evt
          Total      Good    Bad: Region      Time     Phase       Cut
            547       193            354         0         0         0
 Writing events file
    193 events written to the output file
===============================================================================
   Grand Total      Good   Bad:  Region      Time     Phase       Cut
           547       193            354         0         0         0
   in    1344.04 seconds
 Command not found; type ? for a command listing
!xsel:ASCA > set mission ASCA
 
 Notes: XSELECT set up for      ASCA
 Keywords for time and pha are  TIME       PI
 Units of time are              s
 Default timing binsize =    16.00
 Keywords for images are          DETX       DETY
 Keywords for the WMAP are        DETX       DETY
 
!xsel:ASCA > set datadir .
 
Setting data directory to /data/data22/seq_proc/33012010.005/
Setting mkf directory to /data/data22/seq_proc/33012010.005/
 
!xsel:ASCA > read events ad33012010g200370m.evt
Got new instrument: GIS2
 
Setting: IMAGE binning    =    1
         WMAP binning     =    1
         Energy Column    =  PI
         Energy rebinning =    1
 
 
Getting Min and Max for Energy Column...
Got min and max for PI:     0   1023
 
Got the minimum time resolution of the read data:  0.50000
 Number of files read in:   1
 
******************** Observation Catalogue ********************
 
Data Directory is: /data/data22/seq_proc/33012010.005/
HK Directory is: /data/data22/seq_proc/33012010.005/
 
!xsel:ASCA-GIS2-PH > filter region ad33012010g225670_1.reg
!xsel:ASCA-GIS2-PH > extract events
!xsel:ASCA-GIS2-PH > save events outfile=ad33012010g200370m_1.ulc use_events=yes
Wrote events list to file ad33012010g200370m_1.ulc
Changing Data directory from:
    /data/data22/seq_proc/33012010.005/
to the current working directory.
!xsel:ASCA-GIS2-PH > exit save_session=no
-> Extracting unbinned light curve ad33012010g300170h_1.ulc
-> Standard Output From FTOOL xselect:
 
                         **  XSELECT V1.3   **
 
!> Enter session name >[xsel] xsel
 
 Notes: XSELECT set up for      ASCA
 Keywords for time and pha are  TIME       PI
 Units of time are              s
 Default timing binsize =    16.00
 Keywords for images are          DETX       DETY
 Keywords for the WMAP are        DETX       DETY
 
 
 
        OBJECT   DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME   NEVENTS  PHA_BINS
      1 XY_ARI   PH       HIGH     29/01/96 17:43:01 0.38E+04     1552     1024
 
EXTRACTOR vers 2.0  11 Apr 1997.
 Doing file: /data/data22/seq_proc/33012010.005/ad33012010g300170h.evt
          Total      Good    Bad: Region      Time     Phase       Cut
           1552       563            989         0         0         0
 Writing events file
    563 events written to the output file
===============================================================================
   Grand Total      Good   Bad:  Region      Time     Phase       Cut
          1552       563            989         0         0         0
   in    3811.96 seconds
 Command not found; type ? for a command listing
!xsel:ASCA > set mission ASCA
 
 Notes: XSELECT set up for      ASCA
 Keywords for time and pha are  TIME       PI
 Units of time are              s
 Default timing binsize =    16.00
 Keywords for images are          DETX       DETY
 Keywords for the WMAP are        DETX       DETY
 
!xsel:ASCA > set datadir .
 
Setting data directory to /data/data22/seq_proc/33012010.005/
Setting mkf directory to /data/data22/seq_proc/33012010.005/
 
!xsel:ASCA > read events ad33012010g300170h.evt
Got new instrument: GIS3
 
Setting: IMAGE binning    =    1
         WMAP binning     =    1
         Energy Column    =  PI
         Energy rebinning =    1
 
 
Getting Min and Max for Energy Column...
Got min and max for PI:     0   1023
 
Got the minimum time resolution of the read data:  0.62500E-01
 Number of files read in:   1
 
******************** Observation Catalogue ********************
 
Data Directory is: /data/data22/seq_proc/33012010.005/
HK Directory is: /data/data22/seq_proc/33012010.005/
 
!xsel:ASCA-GIS3-PH > filter region ad33012010g325670_1.reg
!xsel:ASCA-GIS3-PH > extract events
!xsel:ASCA-GIS3-PH > save events outfile=ad33012010g300170h_1.ulc use_events=yes
Wrote events list to file ad33012010g300170h_1.ulc
Changing Data directory from:
    /data/data22/seq_proc/33012010.005/
to the current working directory.
!xsel:ASCA-GIS3-PH > exit save_session=no
-> Extracting unbinned light curve ad33012010g300270l_1.ulc
-> Standard Output From FTOOL xselect:
 
                         **  XSELECT V1.3   **
 
!> Enter session name >[xsel] xsel
 
 Notes: XSELECT set up for      ASCA
 Keywords for time and pha are  TIME       PI
 Units of time are              s
 Default timing binsize =    16.00
 Keywords for images are          DETX       DETY
 Keywords for the WMAP are        DETX       DETY
 
 
 
        OBJECT   DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME   NEVENTS  PHA_BINS
      1 XY_ARI   PH       LOW      29/01/96 18:46:29 0.32E+02       18     1024
 
EXTRACTOR vers 2.0  11 Apr 1997.
 Doing file: /data/data22/seq_proc/33012010.005/ad33012010g300270l.evt
          Total      Good    Bad: Region      Time     Phase       Cut
             18        10              8         0         0         0
 Writing events file
     10 events written to the output file
===============================================================================
   Grand Total      Good   Bad:  Region      Time     Phase       Cut
            18        10              8         0         0         0
   in      31.96 seconds
 Command not found; type ? for a command listing
!xsel:ASCA > set mission ASCA
 
 Notes: XSELECT set up for      ASCA
 Keywords for time and pha are  TIME       PI
 Units of time are              s
 Default timing binsize =    16.00
 Keywords for images are          DETX       DETY
 Keywords for the WMAP are        DETX       DETY
 
!xsel:ASCA > set datadir .
 
Setting data directory to /data/data22/seq_proc/33012010.005/
Setting mkf directory to /data/data22/seq_proc/33012010.005/
 
!xsel:ASCA > read events ad33012010g300270l.evt
Got new instrument: GIS3
 
Setting: IMAGE binning    =    1
         WMAP binning     =    1
         Energy Column    =  PI
         Energy rebinning =    1
 
 
Getting Min and Max for Energy Column...
Got min and max for PI:     0   1023
 
Got the minimum time resolution of the read data:   2.0000
 Number of files read in:   1
 
******************** Observation Catalogue ********************
 
Data Directory is: /data/data22/seq_proc/33012010.005/
HK Directory is: /data/data22/seq_proc/33012010.005/
 
!xsel:ASCA-GIS3-PH > filter region ad33012010g325670_1.reg
!xsel:ASCA-GIS3-PH > extract events
!xsel:ASCA-GIS3-PH > save events outfile=ad33012010g300270l_1.ulc use_events=yes
Wrote events list to file ad33012010g300270l_1.ulc
Changing Data directory from:
    /data/data22/seq_proc/33012010.005/
to the current working directory.
!xsel:ASCA-GIS3-PH > exit save_session=no
-> Extracting unbinned light curve ad33012010g300370m_1.ulc
-> Standard Output From FTOOL xselect:
 
                         **  XSELECT V1.3   **
 
!> Enter session name >[xsel] xsel
 
 Notes: XSELECT set up for      ASCA
 Keywords for time and pha are  TIME       PI
 Units of time are              s
 Default timing binsize =    16.00
 Keywords for images are          DETX       DETY
 Keywords for the WMAP are        DETX       DETY
 
 
 
        OBJECT   DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME   NEVENTS  PHA_BINS
      1 XY_ARI   PH       MEDIUM   29/01/96 17:30:29 0.13E+04      623     1024
 
EXTRACTOR vers 2.0  11 Apr 1997.
 Doing file: /data/data22/seq_proc/33012010.005/ad33012010g300370m.evt
          Total      Good    Bad: Region      Time     Phase       Cut
            623       244            379         0         0         0
 Writing events file
    244 events written to the output file
===============================================================================
   Grand Total      Good   Bad:  Region      Time     Phase       Cut
           623       244            379         0         0         0
   in    1344.04 seconds
 Command not found; type ? for a command listing
!xsel:ASCA > set mission ASCA
 
 Notes: XSELECT set up for      ASCA
 Keywords for time and pha are  TIME       PI
 Units of time are              s
 Default timing binsize =    16.00
 Keywords for images are          DETX       DETY
 Keywords for the WMAP are        DETX       DETY
 
!xsel:ASCA > set datadir .
 
Setting data directory to /data/data22/seq_proc/33012010.005/
Setting mkf directory to /data/data22/seq_proc/33012010.005/
 
!xsel:ASCA > read events ad33012010g300370m.evt
Got new instrument: GIS3
 
Setting: IMAGE binning    =    1
         WMAP binning     =    1
         Energy Column    =  PI
         Energy rebinning =    1
 
 
Getting Min and Max for Energy Column...
Got min and max for PI:     0   1023
 
Got the minimum time resolution of the read data:  0.50000
 Number of files read in:   1
 
******************** Observation Catalogue ********************
 
Data Directory is: /data/data22/seq_proc/33012010.005/
HK Directory is: /data/data22/seq_proc/33012010.005/
 
!xsel:ASCA-GIS3-PH > filter region ad33012010g325670_1.reg
!xsel:ASCA-GIS3-PH > extract events
!xsel:ASCA-GIS3-PH > save events outfile=ad33012010g300370m_1.ulc use_events=yes
Wrote events list to file ad33012010g300370m_1.ulc
Changing Data directory from:
    /data/data22/seq_proc/33012010.005/
to the current working directory.
!xsel:ASCA-GIS3-PH > exit save_session=no
-> Extracting unbinned light curve ad33012010s000102h_1.ulc
-> Standard Output From FTOOL xselect:
 
                         **  XSELECT V1.3   **
 
!> Enter session name >[xsel] xsel
 
 Notes: XSELECT set up for      ASCA
 Keywords for time and pha are  TIME       PI
 Units of time are              s
 Default timing binsize =    16.00
 Keywords for images are          DETX       DETY
 Keywords for the WMAP are        DETX       DETY
 
 
 
        OBJECT   DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME   NEVENTS  S0CCDPOW
      1 XY_ARI   BRIGHT   HIGH     29/01/96 17:42:55 0.39E+04      661 0100
 
EXTRACTOR vers 2.0  11 Apr 1997.
 Doing file: /data/data22/seq_proc/33012010.005/ad33012010s000102h.evt
          Total      Good    Bad: Region      Time     Phase       Cut
            661       520            141         0         0         0
 Writing events file
    520 events written to the output file
===============================================================================
   Grand Total      Good   Bad:  Region      Time     Phase       Cut
           661       520            141         0         0         0
   in    3895.92 seconds
 Command not found; type ? for a command listing
!xsel:ASCA > set mission ASCA
 
 Notes: XSELECT set up for      ASCA
 Keywords for time and pha are  TIME       PI
 Units of time are              s
 Default timing binsize =    16.00
 Keywords for images are          DETX       DETY
 Keywords for the WMAP are        DETX       DETY
 
!xsel:ASCA > set datadir .
 
Setting data directory to /data/data22/seq_proc/33012010.005/
Setting mkf directory to /data/data22/seq_proc/33012010.005/
 
!xsel:ASCA > read events ad33012010s000102h.evt
Got new instrument: SIS0
 
Setting: IMAGE binning    =    4
         WMAP binning     =    8
         Energy Column    =  PI
         Energy rebinning =    1
 
 
Getting Min and Max for Energy Column...
Got min and max for PI:     0   2047
 
Got the minimum time resolution of the read data:   4.0000
 Number of files read in:   1
 
******************** Observation Catalogue ********************
 
Data Directory is: /data/data22/seq_proc/33012010.005/
HK Directory is: /data/data22/seq_proc/33012010.005/
 
!xsel:ASCA-SIS0-BRIGHT > filter region ad33012010s032002_1.reg
!xsel:ASCA-SIS0-BRIGHT > extract events
!xsel:ASCA-SIS0-BRIGHT > save events outfile=ad33012010s000102h_1.ulc use_events=yes
Wrote events list to file ad33012010s000102h_1.ulc
Changing Data directory from:
    /data/data22/seq_proc/33012010.005/
to the current working directory.
!xsel:ASCA-SIS0-BRIGHT > exit save_session=no
-> Extracting unbinned light curve ad33012010s000112h_1.ulc
-> Standard Output From FTOOL xselect:
 
                         **  XSELECT V1.3   **
 
!> Enter session name >[xsel] xsel
 
 Notes: XSELECT set up for      ASCA
 Keywords for time and pha are  TIME       PI
 Units of time are              s
 Default timing binsize =    16.00
 Keywords for images are          DETX       DETY
 Keywords for the WMAP are        DETX       DETY
 
 
 
        OBJECT   DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME   NEVENTS  S0CCDPOW
      1 XY_ARI   BRIGHT2  HIGH     29/01/96 17:42:55 0.39E+04      701 0100
 
EXTRACTOR vers 2.0  11 Apr 1997.
 Doing file: /data/data22/seq_proc/33012010.005/ad33012010s000112h.evt
          Total      Good    Bad: Region      Time     Phase       Cut
            701       542            159         0         0         0
 Writing events file
    542 events written to the output file
===============================================================================
   Grand Total      Good   Bad:  Region      Time     Phase       Cut
           701       542            159         0         0         0
   in    3895.92 seconds
 Command not found; type ? for a command listing
!xsel:ASCA > set mission ASCA
 
 Notes: XSELECT set up for      ASCA
 Keywords for time and pha are  TIME       PI
 Units of time are              s
 Default timing binsize =    16.00
 Keywords for images are          DETX       DETY
 Keywords for the WMAP are        DETX       DETY
 
!xsel:ASCA > set datadir .
 
Setting data directory to /data/data22/seq_proc/33012010.005/
Setting mkf directory to /data/data22/seq_proc/33012010.005/
 
!xsel:ASCA > read events ad33012010s000112h.evt
Got new instrument: SIS0
 
Setting: IMAGE binning    =    4
         WMAP binning     =    8
         Energy Column    =  PI
         Energy rebinning =    1
 
 
Getting Min and Max for Energy Column...
Got min and max for PI:     0   4095
 
Got the minimum time resolution of the read data:   4.0000
 Number of files read in:   1
 
******************** Observation Catalogue ********************
 
Data Directory is: /data/data22/seq_proc/33012010.005/
HK Directory is: /data/data22/seq_proc/33012010.005/
 
!xsel:ASCA-SIS0-BRIGHT2 > filter region ad33012010s032002_1.reg
!xsel:ASCA-SIS0-BRIGHT2 > extract events
!xsel:ASCA-SIS0-BRIGHT2 > save events outfile=ad33012010s000112h_1.ulc use_events=yes
Wrote events list to file ad33012010s000112h_1.ulc
Changing Data directory from:
    /data/data22/seq_proc/33012010.005/
to the current working directory.
!xsel:ASCA-SIS0-BRIGHT2 > exit save_session=no
-> Extracting unbinned light curve ad33012010s000302m_1.ulc
-> Standard Output From FTOOL xselect:
 
                         **  XSELECT V1.3   **
 
!> Enter session name >[xsel] xsel
 
 Notes: XSELECT set up for      ASCA
 Keywords for time and pha are  TIME       PI
 Units of time are              s
 Default timing binsize =    16.00
 Keywords for images are          DETX       DETY
 Keywords for the WMAP are        DETX       DETY
 
 
 
        OBJECT   DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME   NEVENTS  S0CCDPOW
      1 XY_ARI   BRIGHT   MEDIUM   29/01/96 17:30:23 0.70E+03      151 0100
 
EXTRACTOR vers 2.0  11 Apr 1997.
 Doing file: /data/data22/seq_proc/33012010.005/ad33012010s000302m.evt
          Total      Good    Bad: Region      Time     Phase       Cut
            151       117             34         0         0         0
 Writing events file
    117 events written to the output file
===============================================================================
   Grand Total      Good   Bad:  Region      Time     Phase       Cut
           151       117             34         0         0         0
   in     695.73 seconds
 Command not found; type ? for a command listing
!xsel:ASCA > set mission ASCA
 
 Notes: XSELECT set up for      ASCA
 Keywords for time and pha are  TIME       PI
 Units of time are              s
 Default timing binsize =    16.00
 Keywords for images are          DETX       DETY
 Keywords for the WMAP are        DETX       DETY
 
!xsel:ASCA > set datadir .
 
Setting data directory to /data/data22/seq_proc/33012010.005/
Setting mkf directory to /data/data22/seq_proc/33012010.005/
 
!xsel:ASCA > read events ad33012010s000302m.evt
Got new instrument: SIS0
 
Setting: IMAGE binning    =    4
         WMAP binning     =    8
         Energy Column    =  PI
         Energy rebinning =    1
 
 
Getting Min and Max for Energy Column...
Got min and max for PI:     0   2047
 
Got the minimum time resolution of the read data:   4.0000
 Number of files read in:   1
 
******************** Observation Catalogue ********************
 
Data Directory is: /data/data22/seq_proc/33012010.005/
HK Directory is: /data/data22/seq_proc/33012010.005/
 
!xsel:ASCA-SIS0-BRIGHT > filter region ad33012010s032002_1.reg
!xsel:ASCA-SIS0-BRIGHT > extract events
!xsel:ASCA-SIS0-BRIGHT > save events outfile=ad33012010s000302m_1.ulc use_events=yes
Wrote events list to file ad33012010s000302m_1.ulc
Changing Data directory from:
    /data/data22/seq_proc/33012010.005/
to the current working directory.
!xsel:ASCA-SIS0-BRIGHT > exit save_session=no
-> Extracting unbinned light curve ad33012010s000312m_1.ulc
-> Standard Output From FTOOL xselect:
 
                         **  XSELECT V1.3   **
 
!> Enter session name >[xsel] xsel
 
 Notes: XSELECT set up for      ASCA
 Keywords for time and pha are  TIME       PI
 Units of time are              s
 Default timing binsize =    16.00
 Keywords for images are          DETX       DETY
 Keywords for the WMAP are        DETX       DETY
 
 
 
        OBJECT   DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME   NEVENTS  S0CCDPOW
      1 XY_ARI   BRIGHT2  MEDIUM   29/01/96 17:30:23 0.70E+03      162 0100
 
EXTRACTOR vers 2.0  11 Apr 1997.
 Doing file: /data/data22/seq_proc/33012010.005/ad33012010s000312m.evt
          Total      Good    Bad: Region      Time     Phase       Cut
            162       125             37         0         0         0
 Writing events file
    125 events written to the output file
===============================================================================
   Grand Total      Good   Bad:  Region      Time     Phase       Cut
           162       125             37         0         0         0
   in     695.73 seconds
 Command not found; type ? for a command listing
!xsel:ASCA > set mission ASCA
 
 Notes: XSELECT set up for      ASCA
 Keywords for time and pha are  TIME       PI
 Units of time are              s
 Default timing binsize =    16.00
 Keywords for images are          DETX       DETY
 Keywords for the WMAP are        DETX       DETY
 
!xsel:ASCA > set datadir .
 
Setting data directory to /data/data22/seq_proc/33012010.005/
Setting mkf directory to /data/data22/seq_proc/33012010.005/
 
!xsel:ASCA > read events ad33012010s000312m.evt
Got new instrument: SIS0
 
Setting: IMAGE binning    =    4
         WMAP binning     =    8
         Energy Column    =  PI
         Energy rebinning =    1
 
 
Getting Min and Max for Energy Column...
Got min and max for PI:     0   4095
 
Got the minimum time resolution of the read data:   4.0000
 Number of files read in:   1
 
******************** Observation Catalogue ********************
 
Data Directory is: /data/data22/seq_proc/33012010.005/
HK Directory is: /data/data22/seq_proc/33012010.005/
 
!xsel:ASCA-SIS0-BRIGHT2 > filter region ad33012010s032002_1.reg
!xsel:ASCA-SIS0-BRIGHT2 > extract events
!xsel:ASCA-SIS0-BRIGHT2 > save events outfile=ad33012010s000312m_1.ulc use_events=yes
Wrote events list to file ad33012010s000312m_1.ulc
Changing Data directory from:
    /data/data22/seq_proc/33012010.005/
to the current working directory.
!xsel:ASCA-SIS0-BRIGHT2 > exit save_session=no
-> Extracting unbinned light curve ad33012010s100102h_1.ulc
-> Standard Output From FTOOL xselect:
 
                         **  XSELECT V1.3   **
 
!> Enter session name >[xsel] xsel
 
 Notes: XSELECT set up for      ASCA
 Keywords for time and pha are  TIME       PI
 Units of time are              s
 Default timing binsize =    16.00
 Keywords for images are          DETX       DETY
 Keywords for the WMAP are        DETX       DETY
 
 
 
        OBJECT   DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME   NEVENTS  S1CCDPOW
      1 XY_ARI   BRIGHT   HIGH     29/01/96 17:42:55 0.39E+04      628 0001
 
EXTRACTOR vers 2.0  11 Apr 1997.
 Doing file: /data/data22/seq_proc/33012010.005/ad33012010s100102h.evt
          Total      Good    Bad: Region      Time     Phase       Cut
            628       507            121         0         0         0
 Writing events file
    507 events written to the output file
===============================================================================
   Grand Total      Good   Bad:  Region      Time     Phase       Cut
           628       507            121         0         0         0
   in    3937.89 seconds
 Command not found; type ? for a command listing
!xsel:ASCA > set mission ASCA
 
 Notes: XSELECT set up for      ASCA
 Keywords for time and pha are  TIME       PI
 Units of time are              s
 Default timing binsize =    16.00
 Keywords for images are          DETX       DETY
 Keywords for the WMAP are        DETX       DETY
 
!xsel:ASCA > set datadir .
 
Setting data directory to /data/data22/seq_proc/33012010.005/
Setting mkf directory to /data/data22/seq_proc/33012010.005/
 
!xsel:ASCA > read events ad33012010s100102h.evt
Got new instrument: SIS1
 
Setting: IMAGE binning    =    4
         WMAP binning     =    8
         Energy Column    =  PI
         Energy rebinning =    1
 
 
Getting Min and Max for Energy Column...
Got min and max for PI:     0   2047
 
Got the minimum time resolution of the read data:   4.0000
 Number of files read in:   1
 
******************** Observation Catalogue ********************
 
Data Directory is: /data/data22/seq_proc/33012010.005/
HK Directory is: /data/data22/seq_proc/33012010.005/
 
!xsel:ASCA-SIS1-BRIGHT > filter region ad33012010s132002_1.reg
!xsel:ASCA-SIS1-BRIGHT > extract events
!xsel:ASCA-SIS1-BRIGHT > save events outfile=ad33012010s100102h_1.ulc use_events=yes
Wrote events list to file ad33012010s100102h_1.ulc
Changing Data directory from:
    /data/data22/seq_proc/33012010.005/
to the current working directory.
!xsel:ASCA-SIS1-BRIGHT > exit save_session=no
-> Extracting unbinned light curve ad33012010s100112h_1.ulc
-> Standard Output From FTOOL xselect:
 
                         **  XSELECT V1.3   **
 
!> Enter session name >[xsel] xsel
 
 Notes: XSELECT set up for      ASCA
 Keywords for time and pha are  TIME       PI
 Units of time are              s
 Default timing binsize =    16.00
 Keywords for images are          DETX       DETY
 Keywords for the WMAP are        DETX       DETY
 
 
 
        OBJECT   DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME   NEVENTS  S1CCDPOW
      1 XY_ARI   BRIGHT2  HIGH     29/01/96 17:42:55 0.39E+04      649 0001
 
EXTRACTOR vers 2.0  11 Apr 1997.
 Doing file: /data/data22/seq_proc/33012010.005/ad33012010s100112h.evt
          Total      Good    Bad: Region      Time     Phase       Cut
            649       516            133         0         0         0
 Writing events file
    516 events written to the output file
===============================================================================
   Grand Total      Good   Bad:  Region      Time     Phase       Cut
           649       516            133         0         0         0
   in    3937.89 seconds
 Command not found; type ? for a command listing
!xsel:ASCA > set mission ASCA
 
 Notes: XSELECT set up for      ASCA
 Keywords for time and pha are  TIME       PI
 Units of time are              s
 Default timing binsize =    16.00
 Keywords for images are          DETX       DETY
 Keywords for the WMAP are        DETX       DETY
 
!xsel:ASCA > set datadir .
 
Setting data directory to /data/data22/seq_proc/33012010.005/
Setting mkf directory to /data/data22/seq_proc/33012010.005/
 
!xsel:ASCA > read events ad33012010s100112h.evt
Got new instrument: SIS1
 
Setting: IMAGE binning    =    4
         WMAP binning     =    8
         Energy Column    =  PI
         Energy rebinning =    1
 
 
Getting Min and Max for Energy Column...
Got min and max for PI:     0   4095
 
Got the minimum time resolution of the read data:   4.0000
 Number of files read in:   1
 
******************** Observation Catalogue ********************
 
Data Directory is: /data/data22/seq_proc/33012010.005/
HK Directory is: /data/data22/seq_proc/33012010.005/
 
!xsel:ASCA-SIS1-BRIGHT2 > filter region ad33012010s132002_1.reg
!xsel:ASCA-SIS1-BRIGHT2 > extract events
!xsel:ASCA-SIS1-BRIGHT2 > save events outfile=ad33012010s100112h_1.ulc use_events=yes
Wrote events list to file ad33012010s100112h_1.ulc
Changing Data directory from:
    /data/data22/seq_proc/33012010.005/
to the current working directory.
!xsel:ASCA-SIS1-BRIGHT2 > exit save_session=no
-> Extracting unbinned light curve ad33012010s100302m_1.ulc
-> Standard Output From FTOOL xselect:
 
                         **  XSELECT V1.3   **
 
!> Enter session name >[xsel] xsel
 
 Notes: XSELECT set up for      ASCA
 Keywords for time and pha are  TIME       PI
 Units of time are              s
 Default timing binsize =    16.00
 Keywords for images are          DETX       DETY
 Keywords for the WMAP are        DETX       DETY
 
 
 
        OBJECT   DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME   NEVENTS  S1CCDPOW
      1 XY_ARI   BRIGHT   MEDIUM   29/01/96 17:30:23 0.79E+03      153 0001
 
EXTRACTOR vers 2.0  11 Apr 1997.
 Doing file: /data/data22/seq_proc/33012010.005/ad33012010s100302m.evt
          Total      Good    Bad: Region      Time     Phase       Cut
            153       127             26         0         0         0
 Writing events file
    127 events written to the output file
===============================================================================
   Grand Total      Good   Bad:  Region      Time     Phase       Cut
           153       127             26         0         0         0
   in     791.73 seconds
 Command not found; type ? for a command listing
!xsel:ASCA > set mission ASCA
 
 Notes: XSELECT set up for      ASCA
 Keywords for time and pha are  TIME       PI
 Units of time are              s
 Default timing binsize =    16.00
 Keywords for images are          DETX       DETY
 Keywords for the WMAP are        DETX       DETY
 
!xsel:ASCA > set datadir .
 
Setting data directory to /data/data22/seq_proc/33012010.005/
Setting mkf directory to /data/data22/seq_proc/33012010.005/
 
!xsel:ASCA > read events ad33012010s100302m.evt
Got new instrument: SIS1
 
Setting: IMAGE binning    =    4
         WMAP binning     =    8
         Energy Column    =  PI
         Energy rebinning =    1
 
 
Getting Min and Max for Energy Column...
Got min and max for PI:     0   2047
 
Got the minimum time resolution of the read data:   4.0000
 Number of files read in:   1
 
******************** Observation Catalogue ********************
 
Data Directory is: /data/data22/seq_proc/33012010.005/
HK Directory is: /data/data22/seq_proc/33012010.005/
 
!xsel:ASCA-SIS1-BRIGHT > filter region ad33012010s132002_1.reg
!xsel:ASCA-SIS1-BRIGHT > extract events
!xsel:ASCA-SIS1-BRIGHT > save events outfile=ad33012010s100302m_1.ulc use_events=yes
Wrote events list to file ad33012010s100302m_1.ulc
Changing Data directory from:
    /data/data22/seq_proc/33012010.005/
to the current working directory.
!xsel:ASCA-SIS1-BRIGHT > exit save_session=no
-> Extracting unbinned light curve ad33012010s100312m_1.ulc
-> Standard Output From FTOOL xselect:
 
                         **  XSELECT V1.3   **
 
!> Enter session name >[xsel] xsel
 
 Notes: XSELECT set up for      ASCA
 Keywords for time and pha are  TIME       PI
 Units of time are              s
 Default timing binsize =    16.00
 Keywords for images are          DETX       DETY
 Keywords for the WMAP are        DETX       DETY
 
 
 
        OBJECT   DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME   NEVENTS  S1CCDPOW
      1 XY_ARI   BRIGHT2  MEDIUM   29/01/96 17:30:23 0.79E+03      158 0001
 
EXTRACTOR vers 2.0  11 Apr 1997.
 Doing file: /data/data22/seq_proc/33012010.005/ad33012010s100312m.evt
          Total      Good    Bad: Region      Time     Phase       Cut
            158       131             27         0         0         0
 Writing events file
    131 events written to the output file
===============================================================================
   Grand Total      Good   Bad:  Region      Time     Phase       Cut
           158       131             27         0         0         0
   in     791.73 seconds
 Command not found; type ? for a command listing
!xsel:ASCA > set mission ASCA
 
 Notes: XSELECT set up for      ASCA
 Keywords for time and pha are  TIME       PI
 Units of time are              s
 Default timing binsize =    16.00
 Keywords for images are          DETX       DETY
 Keywords for the WMAP are        DETX       DETY
 
!xsel:ASCA > set datadir .
 
Setting data directory to /data/data22/seq_proc/33012010.005/
Setting mkf directory to /data/data22/seq_proc/33012010.005/
 
!xsel:ASCA > read events ad33012010s100312m.evt
Got new instrument: SIS1
 
Setting: IMAGE binning    =    4
         WMAP binning     =    8
         Energy Column    =  PI
         Energy rebinning =    1
 
 
Getting Min and Max for Energy Column...
Got min and max for PI:     0   4095
 
Got the minimum time resolution of the read data:   4.0000
 Number of files read in:   1
 
******************** Observation Catalogue ********************
 
Data Directory is: /data/data22/seq_proc/33012010.005/
HK Directory is: /data/data22/seq_proc/33012010.005/
 
!xsel:ASCA-SIS1-BRIGHT2 > filter region ad33012010s132002_1.reg
!xsel:ASCA-SIS1-BRIGHT2 > extract events
!xsel:ASCA-SIS1-BRIGHT2 > save events outfile=ad33012010s100312m_1.ulc use_events=yes
Wrote events list to file ad33012010s100312m_1.ulc
Changing Data directory from:
    /data/data22/seq_proc/33012010.005/
to the current working directory.
!xsel:ASCA-SIS1-BRIGHT2 > exit save_session=no

Extracting FRAME mode data ( 15:33:46 )

-> Extracting frame mode data from ft960129_1730.2300
-> Standard Output From STOOL tlmFrm:
 *** tlmFrm Version 1.1 (1997-08-25) *** 
total number of superframes: 3248

Total of 0 sets of frame data are extracted.

Extracting GIS calibration source spectra ( 15:34:05 )

-> Standard Output From STOOL group_event_files:
1 ad33012010g200170h.unf 11466
1 ad33012010g200270l.unf 11466
1 ad33012010g200370m.unf 11466
-> Fetching GIS2_CALSRC256.2
-> Extracting ad33012010g220170.cal from ad33012010g200170h.unf ad33012010g200270l.unf ad33012010g200370m.unf
-> Standard Output From FTOOL xselect:
 
                         **  XSELECT V1.3   **
 
!> Enter session name >[xsel] xsel
 
 Notes: XSELECT set up for      ASCA
 Keywords for time and pha are  TIME       PI
 Units of time are              s
 Default timing binsize =    16.00
 Keywords for images are          DETX       DETY
 Keywords for the WMAP are        DETX       DETY
 
 
 
        OBJECT   DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME   NEVENTS  PHA_BINS
      1 XY_ARI   PH       HIGH     29/01/96 17:43:01 0.48E+04     4638     1024
 
 
 
        OBJECT   DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME   NEVENTS  PHA_BINS
      1 XY_ARI   PH       HIGH     29/01/96 17:43:01 0.48E+04     4638     1024
      2 XY_ARI   PH       LOW      29/01/96 18:46:29 0.61E+04     3925     1024
 
 
 
        OBJECT   DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME   NEVENTS  PHA_BINS
      1 XY_ARI   PH       HIGH     29/01/96 17:43:01 0.48E+04     4638     1024
      2 XY_ARI   PH       LOW      29/01/96 18:46:29 0.61E+04     3925     1024
      3 XY_ARI   PH       MEDIUM   29/01/96 17:30:29 0.33E+04     2903     1024
 
EXTRACTOR vers 2.0  11 Apr 1997.
 Getting FITS WCS Keywords
 Doing file: /data/data22/seq_proc/33012010.005/ad33012010g200170h.unf
          Total      Good    Bad: Region      Time     Phase       Cut
           4638       960           3678         0         0         0
 Doing file: /data/data22/seq_proc/33012010.005/ad33012010g200270l.unf
          Total      Good    Bad: Region      Time     Phase       Cut
           3925      1185           2740         0         0         0
 Doing file: /data/data22/seq_proc/33012010.005/ad33012010g200370m.unf
          Total      Good    Bad: Region      Time     Phase       Cut
           2903       610           2293         0         0         0
===============================================================================
   Grand Total      Good   Bad:  Region      Time     Phase       Cut
         11466      2755           8711         0         0         0
   in   14335.96 seconds
 Spectrum         has     2755 counts for 0.1922     counts/sec
 
  -------------------------
  MANDATORY KEYWORDS/VALUES
  -------------------------
  --------------------------------------------------------------------
  --------------------------------------------------------------------
  EXTNAME   - SPECTRUM        Name of this BINTABLE
  TELESCOP  - ASCA            Mission/Satellite name
  INSTRUME  - GIS2            Instrument/Detector
  FILTER    -                 Instrument filter in use
  EXPOSURE  - 14336.          Integration time (in secs) of PHA data
  AREASCAL  - 1.0000          Area scaling factor
  BACKSCAL  - 3.57971E-02     Background scaling factor
  BACKFILE  - NONE            Associated background file
  CORRSCAL  - 1.0000          Correlation scaling factor
  CORRFILE  - none            Associated correlation file
  RESPFILE  - NONE            Associated redistribution matrix file
  ANCRFILE  - none            Associated ancillary response file
  XFLT0001  - none            XSPEC selection filter
  POISSERR  - TRUE            Whether Poissonian errors apply
  CHANTYPE  - PI              Whether channels have been corrected
  TLMIN1    - 0               First legal Detector channel
  DETCHANS  - 1024            No. of legal detector channels
  NCHAN     - 1024            No. of detector channels in dataset
  PHAVERSN  - 1992a           OGIP FITS version number
  STAT_ERR  - FALSE           Statistical Error
  SYS_ERR   - TRUE            Fractional Systematic Error
  QUALITY   - TRUE            Quality Flag
  GROUPING  - FALSE           Grouping Flag
  --------------------------------------------------------------------
  --------------------------------------------------------------------
 ...
 ...  --------
 ...  GROUPING
 ...  --------
 ...  ---------------------------------------------
 ...  Channel Grouping (Channel-Channel) :
 ...  ---------------------------------------------
 ...
 ...... exiting, changes written to file : ad33012010g220170.cal
 Command not found; type ? for a command listing
!xsel:ASCA > set mission ASCA
 
 Notes: XSELECT set up for      ASCA
 Keywords for time and pha are  TIME       PI
 Units of time are              s
 Default timing binsize =    16.00
 Keywords for images are          DETX       DETY
 Keywords for the WMAP are        DETX       DETY
 
!xsel:ASCA > set datadir .
 
Setting data directory to /data/data22/seq_proc/33012010.005/
Setting mkf directory to /data/data22/seq_proc/33012010.005/
 
!xsel:ASCA > read events ad33012010g200170h.unf
Got new instrument: GIS2
 
Setting: IMAGE binning    =    1
         WMAP binning     =    1
         Energy Column    =  PI
         Energy rebinning =    1
 
 
Getting Min and Max for Energy Column...
Got min and max for PI:     0   1023
 
Got the minimum time resolution of the read data:  0.62500E-01
 Number of files read in:   1
 
******************** Observation Catalogue ********************
 
Data Directory is: /data/data22/seq_proc/33012010.005/
HK Directory is: /data/data22/seq_proc/33012010.005/
 
!xsel:ASCA-GIS2-PH > read events ad33012010g200270l.unf
 
Getting Min and Max for Energy Column...
Got min and max for PI:     0   1023
 
Got the minimum time resolution of the read data:   2.0000
 Number of files read in:   2
 
******************** Observation Catalogue ********************
 
Data Directory is: /data/data22/seq_proc/33012010.005/
HK Directory is: /data/data22/seq_proc/33012010.005/
 
!xsel:ASCA-GIS2-PH > read events ad33012010g200370m.unf
 
Getting Min and Max for Energy Column...
Got min and max for PI:     0   1023
 
Got the minimum time resolution of the read data:  0.50000
 Number of files read in:   3
 
******************** Observation Catalogue ********************
 
Data Directory is: /data/data22/seq_proc/33012010.005/
HK Directory is: /data/data22/seq_proc/33012010.005/
 
!xsel:ASCA-GIS2-PH > filter region GIS2_CALSRC256.2
!xsel:ASCA-GIS2-PH > extract spectrum
!xsel:ASCA-GIS2-PH > save spectrum ad33012010g220170.cal group=yes
Wrote spectrum to ad33012010g220170.cal
!xsel:ASCA-GIS2-PH > exit save_session=no
-> gis2v4_0.rmf already present in current directory
-> Plotting ad33012010g220170_cal.ps and finding peak
-> Standard Output From STOOL xspec:
 
               XSPEC 9.01 15:34:53 17-May-98
 
 Plot device not set, use "cpd" to set it
 
 Type "help" or "?" for further information
!XSPEC> query yes
Querying disabled - assuming answer is yes
!XSPEC> data ad33012010g220170.cal
 Net count rate (cts/s) for file   1  0.1922    +/-  3.6858E-03
   1 data set is in use
!XSPEC> ignore bad
!XSPEC> ignore **-4.0
!XSPEC> ignore 8.0-**
!XSPEC> model const/b + gauss/b + gauss/b
Background components must be from the additive model list
  mo = constant[1] ) + gaussian/b[2] + gaussian/b[3]
 Input parameter value, delta, min, bot, top, and max values for ...
 Mod parameter  1 of component  1 constant factor
    1.000      1.0000E-02      0.          0.      1.0000E+10  1.0000E+10
!
 Mod parameter  2 of component  2 gaussian LineE
    6.500      5.0000E-02      0.          0.      1.0000E+06  1.0000E+06
! 5.9
 Mod parameter  3 of component  2 gaussian Sigma
   0.1000      5.0000E-02      0.          0.       10.00       20.00
! 0.0
 Mod parameter  4 of component  2 gaussian norm
    1.000      1.0000E-02      0.          0.      1.0000E+24  1.0000E+24
!
 Mod parameter  5 of component  3 gaussian LineE
    6.500      5.0000E-02      0.          0.      1.0000E+06  1.0000E+06
! 6.5
 Mod parameter  6 of component  3 gaussian Sigma
   0.1000      5.0000E-02      0.          0.       10.00       20.00
! 0.0
 Mod parameter  7 of component  3 gaussian norm
    1.000      1.0000E-02      0.          0.      1.0000E+24  1.0000E+24
!
  ---------------------------------------------------------------------------
  ---------------------------------------------------------------------------
  mo = constant[1] ) + gaussian/b[2] + gaussian/b[3]
  Model Fit Model   Component     Parameter   Value
  par   par comp
    1    1    1       constant    factor     1.00000     +/-      0.
    2    2    2       gaussian/b  LineE      5.90000     +/-      0.
    3    3    2       gaussian/b  Sigma           0.     +/-      0.
    4    4    2       gaussian/b  norm       1.00000     +/-      0.
    5    5    3       gaussian/b  LineE      6.50000     +/-      0.
    6    6    3       gaussian/b  Sigma           0.     +/-      0.
    7    7    3       gaussian/b  norm       1.00000     +/-      0.
  ---------------------------------------------------------------------------
  ---------------------------------------------------------------------------
    7 variable fit parameters
 Chi-Squared =     4.8108E+05 using    84 PHA bins.
 Reduced chi-squared =      6248.
!XSPEC> newpar 5 = 2 1.101005
    6 variable fit parameters
 Chi-Squared =     4.7697E+05 using    84 PHA bins.
 Reduced chi-squared =      6115.
!XSPEC> newpar 6 = 3 1.049288
    5 variable fit parameters
 Chi-Squared =     4.7697E+05 using    84 PHA bins.
 Reduced chi-squared =      6038.
!XSPEC> renorm
 Chi-Squared =      846.1     using    84 PHA bins.
 Reduced chi-squared =      10.71
!XSPEC> fit
 Chi-Squared  Lvl  Fit param # 1     2           3           4
                 5
 Due to zero model norms
  fit parameter  1 is temporarily frozen
   694.14      0      1.000       5.893      8.4557E-02  5.8197E-02
              5.0946E-02
 Due to zero model norms
  fit parameter  1 is temporarily frozen
   303.23      0      1.000       5.865      0.1392      8.6815E-02
              4.4453E-02
 Due to zero model norms
  fit parameter  1 is temporarily frozen
   155.51     -1      1.000       5.903      0.1641      0.1203
              3.1105E-02
 Due to zero model norms
  fit parameter  1 is temporarily frozen
   130.10     -2      1.000       5.948      0.1875      0.1365
              2.0116E-02
 Due to zero model norms
  fit parameter  1 is temporarily frozen
   129.93     -3      1.000       5.945      0.1842      0.1362
              2.0539E-02
 Due to zero model norms
  fit parameter  1 is temporarily frozen
   129.92     -4      1.000       5.945      0.1839      0.1363
              2.0516E-02
  ---------------------------------------------------------------------------
  ---------------------------------------------------------------------------
  mo = constant[1] ) + gaussian/b[2] + gaussian/b[3]
  Model Fit Model   Component     Parameter   Value
  par   par comp
    1    1    1       constant    factor     1.00000     +/- -1.0000
    2    2    2       gaussian/b  LineE      5.94502     +/- 0.10186E-01
    3    3    2       gaussian/b  Sigma     0.183851     +/- 0.11379E-01
    4    4    2       gaussian/b  norm      0.136253     +/- 0.38697E-02
    5    2    3       gaussian/b  LineE      6.54549     = par   2 *  1.1010
    6    3    3       gaussian/b  Sigma     0.192912     = par   3 *  1.0493
    7    5    3       gaussian/b  norm      2.051648E-02 +/- 0.25754E-02
  ---------------------------------------------------------------------------
  ---------------------------------------------------------------------------
 Chi-Squared =      129.9     using    84 PHA bins.
 Reduced chi-squared =      1.645
!XSPEC> setplot energy
!XSPEC> iplot data
!PLT> label top GIS2 Calibration Source, should peak near 5.9 keV
!PLT> log x off
!PLT> rescale x 4 8
!PLT> hard /ps
!PLT> quit
!XSPEC> exit
!Do you really want to exit (y) y
 XSPEC: quit
-> Calibration source ad33012010g220170.cal peaks at 5.94502 +/- 0.010186 keV
-> Standard Output From STOOL group_event_files:
1 ad33012010g300170h.unf 10853
1 ad33012010g300270l.unf 10853
1 ad33012010g300370m.unf 10853
-> Fetching GIS3_CALSRC256.2
-> Extracting ad33012010g320170.cal from ad33012010g300170h.unf ad33012010g300270l.unf ad33012010g300370m.unf
-> Standard Output From FTOOL xselect:
 
                         **  XSELECT V1.3   **
 
!> Enter session name >[xsel] xsel
 
 Notes: XSELECT set up for      ASCA
 Keywords for time and pha are  TIME       PI
 Units of time are              s
 Default timing binsize =    16.00
 Keywords for images are          DETX       DETY
 Keywords for the WMAP are        DETX       DETY
 
 
 
        OBJECT   DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME   NEVENTS  PHA_BINS
      1 XY_ARI   PH       HIGH     29/01/96 17:43:01 0.48E+04     4397     1024
 
 
 
        OBJECT   DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME   NEVENTS  PHA_BINS
      1 XY_ARI   PH       HIGH     29/01/96 17:43:01 0.48E+04     4397     1024
      2 XY_ARI   PH       LOW      29/01/96 18:46:29 0.60E+04     3589     1024
 
 
 
        OBJECT   DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME   NEVENTS  PHA_BINS
      1 XY_ARI   PH       HIGH     29/01/96 17:43:01 0.48E+04     4397     1024
      2 XY_ARI   PH       LOW      29/01/96 18:46:29 0.60E+04     3589     1024
      3 XY_ARI   PH       MEDIUM   29/01/96 17:30:29 0.33E+04     2867     1024
 
EXTRACTOR vers 2.0  11 Apr 1997.
 Getting FITS WCS Keywords
 Doing file: /data/data22/seq_proc/33012010.005/ad33012010g300170h.unf
          Total      Good    Bad: Region      Time     Phase       Cut
           4397       886           3511         0         0         0
 Doing file: /data/data22/seq_proc/33012010.005/ad33012010g300270l.unf
          Total      Good    Bad: Region      Time     Phase       Cut
           3589      1050           2539         0         0         0
 Doing file: /data/data22/seq_proc/33012010.005/ad33012010g300370m.unf
          Total      Good    Bad: Region      Time     Phase       Cut
           2867       565           2302         0         0         0
===============================================================================
   Grand Total      Good   Bad:  Region      Time     Phase       Cut
         10853      2501           8352         0         0         0
   in   14205.96 seconds
 Spectrum         has     2501 counts for 0.1761     counts/sec
 
  -------------------------
  MANDATORY KEYWORDS/VALUES
  -------------------------
  --------------------------------------------------------------------
  --------------------------------------------------------------------
  EXTNAME   - SPECTRUM        Name of this BINTABLE
  TELESCOP  - ASCA            Mission/Satellite name
  INSTRUME  - GIS3            Instrument/Detector
  FILTER    -                 Instrument filter in use
  EXPOSURE  - 14206.          Integration time (in secs) of PHA data
  AREASCAL  - 1.0000          Area scaling factor
  BACKSCAL  - 2.83356E-02     Background scaling factor
  BACKFILE  - NONE            Associated background file
  CORRSCAL  - 1.0000          Correlation scaling factor
  CORRFILE  - none            Associated correlation file
  RESPFILE  - NONE            Associated redistribution matrix file
  ANCRFILE  - none            Associated ancillary response file
  XFLT0001  - none            XSPEC selection filter
  POISSERR  - TRUE            Whether Poissonian errors apply
  CHANTYPE  - PI              Whether channels have been corrected
  TLMIN1    - 0               First legal Detector channel
  DETCHANS  - 1024            No. of legal detector channels
  NCHAN     - 1024            No. of detector channels in dataset
  PHAVERSN  - 1992a           OGIP FITS version number
  STAT_ERR  - FALSE           Statistical Error
  SYS_ERR   - TRUE            Fractional Systematic Error
  QUALITY   - TRUE            Quality Flag
  GROUPING  - FALSE           Grouping Flag
  --------------------------------------------------------------------
  --------------------------------------------------------------------
 ...
 ...  --------
 ...  GROUPING
 ...  --------
 ...  ---------------------------------------------
 ...  Channel Grouping (Channel-Channel) :
 ...  ---------------------------------------------
 ...
 ...... exiting, changes written to file : ad33012010g320170.cal
 Command not found; type ? for a command listing
!xsel:ASCA > set mission ASCA
 
 Notes: XSELECT set up for      ASCA
 Keywords for time and pha are  TIME       PI
 Units of time are              s
 Default timing binsize =    16.00
 Keywords for images are          DETX       DETY
 Keywords for the WMAP are        DETX       DETY
 
!xsel:ASCA > set datadir .
 
Setting data directory to /data/data22/seq_proc/33012010.005/
Setting mkf directory to /data/data22/seq_proc/33012010.005/
 
!xsel:ASCA > read events ad33012010g300170h.unf
Got new instrument: GIS3
 
Setting: IMAGE binning    =    1
         WMAP binning     =    1
         Energy Column    =  PI
         Energy rebinning =    1
 
 
Getting Min and Max for Energy Column...
Got min and max for PI:     0   1023
 
Got the minimum time resolution of the read data:  0.62500E-01
 Number of files read in:   1
 
******************** Observation Catalogue ********************
 
Data Directory is: /data/data22/seq_proc/33012010.005/
HK Directory is: /data/data22/seq_proc/33012010.005/
 
!xsel:ASCA-GIS3-PH > read events ad33012010g300270l.unf
 
Getting Min and Max for Energy Column...
Got min and max for PI:     0   1023
 
Got the minimum time resolution of the read data:   2.0000
 Number of files read in:   2
 
******************** Observation Catalogue ********************
 
Data Directory is: /data/data22/seq_proc/33012010.005/
HK Directory is: /data/data22/seq_proc/33012010.005/
 
!xsel:ASCA-GIS3-PH > read events ad33012010g300370m.unf
 
Getting Min and Max for Energy Column...
Got min and max for PI:     0   1023
 
Got the minimum time resolution of the read data:  0.50000
 Number of files read in:   3
 
******************** Observation Catalogue ********************
 
Data Directory is: /data/data22/seq_proc/33012010.005/
HK Directory is: /data/data22/seq_proc/33012010.005/
 
!xsel:ASCA-GIS3-PH > filter region GIS3_CALSRC256.2
!xsel:ASCA-GIS3-PH > extract spectrum
!xsel:ASCA-GIS3-PH > save spectrum ad33012010g320170.cal group=yes
Wrote spectrum to ad33012010g320170.cal
!xsel:ASCA-GIS3-PH > exit save_session=no
-> gis3v4_0.rmf already present in current directory
-> Plotting ad33012010g320170_cal.ps and finding peak
-> Standard Output From STOOL xspec:
 
               XSPEC 9.01 15:35:50 17-May-98
 
 Plot device not set, use "cpd" to set it
 
 Type "help" or "?" for further information
!XSPEC> query yes
Querying disabled - assuming answer is yes
!XSPEC> data ad33012010g320170.cal
 Net count rate (cts/s) for file   1  0.1761    +/-  3.5637E-03
   1 data set is in use
!XSPEC> ignore bad
!XSPEC> ignore **-4.0
!XSPEC> ignore 8.0-**
!XSPEC> model const/b + gauss/b + gauss/b
Background components must be from the additive model list
  mo = constant[1] ) + gaussian/b[2] + gaussian/b[3]
 Input parameter value, delta, min, bot, top, and max values for ...
 Mod parameter  1 of component  1 constant factor
    1.000      1.0000E-02      0.          0.      1.0000E+10  1.0000E+10
!
 Mod parameter  2 of component  2 gaussian LineE
    6.500      5.0000E-02      0.          0.      1.0000E+06  1.0000E+06
! 5.9
 Mod parameter  3 of component  2 gaussian Sigma
   0.1000      5.0000E-02      0.          0.       10.00       20.00
! 0.0
 Mod parameter  4 of component  2 gaussian norm
    1.000      1.0000E-02      0.          0.      1.0000E+24  1.0000E+24
!
 Mod parameter  5 of component  3 gaussian LineE
    6.500      5.0000E-02      0.          0.      1.0000E+06  1.0000E+06
! 6.5
 Mod parameter  6 of component  3 gaussian Sigma
   0.1000      5.0000E-02      0.          0.       10.00       20.00
! 0.0
 Mod parameter  7 of component  3 gaussian norm
    1.000      1.0000E-02      0.          0.      1.0000E+24  1.0000E+24
!
  ---------------------------------------------------------------------------
  ---------------------------------------------------------------------------
  mo = constant[1] ) + gaussian/b[2] + gaussian/b[3]
  Model Fit Model   Component     Parameter   Value
  par   par comp
    1    1    1       constant    factor     1.00000     +/-      0.
    2    2    2       gaussian/b  LineE      5.90000     +/-      0.
    3    3    2       gaussian/b  Sigma           0.     +/-      0.
    4    4    2       gaussian/b  norm       1.00000     +/-      0.
    5    5    3       gaussian/b  LineE      6.50000     +/-      0.
    6    6    3       gaussian/b  Sigma           0.     +/-      0.
    7    7    3       gaussian/b  norm       1.00000     +/-      0.
  ---------------------------------------------------------------------------
  ---------------------------------------------------------------------------
    7 variable fit parameters
 Chi-Squared =     5.5436E+05 using    84 PHA bins.
 Reduced chi-squared =      7200.
!XSPEC> newpar 5 = 2 1.101005
    6 variable fit parameters
 Chi-Squared =     5.4949E+05 using    84 PHA bins.
 Reduced chi-squared =      7045.
!XSPEC> newpar 6 = 3 1.049288
    5 variable fit parameters
 Chi-Squared =     5.4949E+05 using    84 PHA bins.
 Reduced chi-squared =      6956.
!XSPEC> renorm
 Chi-Squared =      917.9     using    84 PHA bins.
 Reduced chi-squared =      11.62
!XSPEC> fit
 Chi-Squared  Lvl  Fit param # 1     2           3           4
                 5
 Due to zero model norms
  fit parameter  1 is temporarily frozen
   739.18      0      1.000       5.892      9.3573E-02  5.2227E-02
              4.4301E-02
 Due to zero model norms
  fit parameter  1 is temporarily frozen
   276.84      0      1.000       5.860      0.1417      8.5189E-02
              3.8182E-02
 Due to zero model norms
  fit parameter  1 is temporarily frozen
   100.48     -1      1.000       5.905      0.1531      0.1225
              2.4570E-02
 Due to zero model norms
  fit parameter  1 is temporarily frozen
   87.163     -2      1.000       5.932      0.1656      0.1344
              1.7823E-02
 Due to zero model norms
  fit parameter  1 is temporarily frozen
   86.835     -3      1.000       5.928      0.1606      0.1336
              1.8614E-02
 Due to zero model norms
  fit parameter  1 is temporarily frozen
   86.831     -4      1.000       5.928      0.1609      0.1337
              1.8487E-02
  ---------------------------------------------------------------------------
  ---------------------------------------------------------------------------
  mo = constant[1] ) + gaussian/b[2] + gaussian/b[3]
  Model Fit Model   Component     Parameter   Value
  par   par comp
    1    1    1       constant    factor     1.00000     +/- -1.0000
    2    2    2       gaussian/b  LineE      5.92830     +/- 0.91057E-02
    3    3    2       gaussian/b  Sigma     0.160894     +/- 0.10838E-01
    4    4    2       gaussian/b  norm      0.133708     +/- 0.36508E-02
    5    2    3       gaussian/b  LineE      6.52709     = par   2 *  1.1010
    6    3    3       gaussian/b  Sigma     0.168824     = par   3 *  1.0493
    7    5    3       gaussian/b  norm      1.848738E-02 +/- 0.22203E-02
  ---------------------------------------------------------------------------
  ---------------------------------------------------------------------------
 Chi-Squared =      86.83     using    84 PHA bins.
 Reduced chi-squared =      1.099
!XSPEC> setplot energy
!XSPEC> iplot data
!PLT> label top GIS3 Calibration Source, should peak near 5.9 keV
!PLT> log x off
!PLT> rescale x 4 8
!PLT> hard /ps
!PLT> quit
!XSPEC> exit
!Do you really want to exit (y) y
 XSPEC: quit
-> Calibration source ad33012010g320170.cal peaks at 5.92830 +/- 0.0091057 keV

Extracting bright and dark Earth event files. ( 15:36:01 )

-> Extracting bright and dark Earth events from ad33012010s000102h.unf
-> Extracting ad33012010s000102h.drk
-> Standard Output From FTOOL xselect:
 
                         **  XSELECT V1.3   **
 
!> Enter session name >[xsel] earthevents
 
 Notes: XSELECT set up for      ASCA
 Keywords for time and pha are  TIME       PI
 Units of time are              s
 Default timing binsize =    16.00
 Keywords for images are          DETX       DETY
 Keywords for the WMAP are        DETX       DETY
 
 
 
        OBJECT   DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME   NEVENTS  S0CCDPOW
      1 XY_ARI   BRIGHT   HIGH     29/01/96 17:42:55 0.55E+04     3311 0100
 
EXTRACTOR vers 2.0  11 Apr 1997.
 Skipping file: /data/data22/seq_proc/33012010.005/ad33012010s000102h.unf
 Writing events file
      0 events written to the output file
===============================================================================
   Grand Total      Good   Bad:  Region      Time     Phase       Cut
             0         0              0         0         0         0
   in       0.00 seconds
 Command not found; type ? for a command listing
!earthevents:ASCA > set mission ASCA
 
 Notes: XSELECT set up for      ASCA
 Keywords for time and pha are  TIME       PI
 Units of time are              s
 Default timing binsize =    16.00
 Keywords for images are          DETX       DETY
 Keywords for the WMAP are        DETX       DETY
 
!earthevents:ASCA > set datadir .
 
Setting data directory to /data/data22/seq_proc/33012010.005/
Setting mkf directory to /data/data22/seq_proc/33012010.005/
 
!earthevents:ASCA > read events ad33012010s000102h.unf
Got new instrument: SIS0
 
Setting: IMAGE binning    =    4
         WMAP binning     =    8
         Energy Column    =  PI
         Energy rebinning =    1
 
 
Getting Min and Max for Energy Column...
Got min and max for PI:     0   2047
 
Got the minimum time resolution of the read data:   4.0000
 Number of files read in:   1
 
******************** Observation Catalogue ********************
 
Data Directory is: /data/data22/seq_proc/33012010.005/
HK Directory is: /data/data22/seq_proc/33012010.005/
 
!earthevents:ASCA-SIS0-BRIGHT > select mkf "FOV==1"  data_dir=. ASCA_mkf_def_expr=ft*.mkf
!earthevents:ASCA-SIS0-BRIGHT > extract events
!earthevents:ASCA-SIS0-BRIGHT > save events outfile=event.tmp use_events=no
Wrote events list to file event.tmp
!earthevents:ASCA-SIS0-BRIGHT > exit save_session=no
-> Deleting ad33012010s000102h.drk since it contains 0 events
-> Extracting bright and dark Earth events from ad33012010s000112h.unf
-> Extracting ad33012010s000112h.drk
-> Standard Output From FTOOL xselect:
 
                         **  XSELECT V1.3   **
 
!> Enter session name >[xsel] earthevents
 
 Notes: XSELECT set up for      ASCA
 Keywords for time and pha are  TIME       PI
 Units of time are              s
 Default timing binsize =    16.00
 Keywords for images are          DETX       DETY
 Keywords for the WMAP are        DETX       DETY
 
 
 
        OBJECT   DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME   NEVENTS  S0CCDPOW
      1 XY_ARI   BRIGHT2  HIGH     29/01/96 17:42:55 0.55E+04     3460 0100
 
EXTRACTOR vers 2.0  11 Apr 1997.
 Skipping file: /data/data22/seq_proc/33012010.005/ad33012010s000112h.unf
 Writing events file
      0 events written to the output file
===============================================================================
   Grand Total      Good   Bad:  Region      Time     Phase       Cut
             0         0              0         0         0         0
   in       0.00 seconds
 Command not found; type ? for a command listing
!earthevents:ASCA > set mission ASCA
 
 Notes: XSELECT set up for      ASCA
 Keywords for time and pha are  TIME       PI
 Units of time are              s
 Default timing binsize =    16.00
 Keywords for images are          DETX       DETY
 Keywords for the WMAP are        DETX       DETY
 
!earthevents:ASCA > set datadir .
 
Setting data directory to /data/data22/seq_proc/33012010.005/
Setting mkf directory to /data/data22/seq_proc/33012010.005/
 
!earthevents:ASCA > read events ad33012010s000112h.unf
Got new instrument: SIS0
 
Setting: IMAGE binning    =    4
         WMAP binning     =    8
         Energy Column    =  PI
         Energy rebinning =    1
 
 
Getting Min and Max for Energy Column...
Got min and max for PI:     0   4095
 
Got the minimum time resolution of the read data:   4.0000
 Number of files read in:   1
 
******************** Observation Catalogue ********************
 
Data Directory is: /data/data22/seq_proc/33012010.005/
HK Directory is: /data/data22/seq_proc/33012010.005/
 
!earthevents:ASCA-SIS0-BRIGHT2 > select mkf "FOV==1"  data_dir=. ASCA_mkf_def_expr=ft*.mkf
!earthevents:ASCA-SIS0-BRIGHT2 > extract events
!earthevents:ASCA-SIS0-BRIGHT2 > save events outfile=event.tmp use_events=no
Wrote events list to file event.tmp
!earthevents:ASCA-SIS0-BRIGHT2 > exit save_session=no
-> Deleting ad33012010s000112h.drk since it contains 0 events
-> Extracting bright and dark Earth events from ad33012010s000202l.unf
-> Extracting ad33012010s000202l.drk
-> Standard Output From FTOOL xselect:
 
                         **  XSELECT V1.3   **
 
!> Enter session name >[xsel] earthevents
 
 Notes: XSELECT set up for      ASCA
 Keywords for time and pha are  TIME       PI
 Units of time are              s
 Default timing binsize =    16.00
 Keywords for images are          DETX       DETY
 Keywords for the WMAP are        DETX       DETY
 
 
 
        OBJECT   DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME   NEVENTS  S0CCDPOW
      1 XY_ARI   BRIGHT   LOW      29/01/96 18:44:15 0.77E+04     2473 0100
 
EXTRACTOR vers 2.0  11 Apr 1997.
 Doing file: /data/data22/seq_proc/33012010.005/ad33012010s000202l.unf
          Total      Good    Bad: Region      Time     Phase       Cut
           2473      1142              0      1331         0         0
 Writing events file
   1142 events written to the output file
===============================================================================
   Grand Total      Good   Bad:  Region      Time     Phase       Cut
          2473      1142              0      1331         0         0
   in    3296.00 seconds
 Command not found; type ? for a command listing
!earthevents:ASCA > set mission ASCA
 
 Notes: XSELECT set up for      ASCA
 Keywords for time and pha are  TIME       PI
 Units of time are              s
 Default timing binsize =    16.00
 Keywords for images are          DETX       DETY
 Keywords for the WMAP are        DETX       DETY
 
!earthevents:ASCA > set datadir .
 
Setting data directory to /data/data22/seq_proc/33012010.005/
Setting mkf directory to /data/data22/seq_proc/33012010.005/
 
!earthevents:ASCA > read events ad33012010s000202l.unf
Got new instrument: SIS0
 
Setting: IMAGE binning    =    4
         WMAP binning     =    8
         Energy Column    =  PI
         Energy rebinning =    1
 
 
Getting Min and Max for Energy Column...
Got min and max for PI:     0   2047
 
Got the minimum time resolution of the read data:   4.0000
 Number of files read in:   1
 
******************** Observation Catalogue ********************
 
Data Directory is: /data/data22/seq_proc/33012010.005/
HK Directory is: /data/data22/seq_proc/33012010.005/
 
!earthevents:ASCA-SIS0-BRIGHT > select mkf "FOV==1"  data_dir=. ASCA_mkf_def_expr=ft*.mkf
!earthevents:ASCA-SIS0-BRIGHT > extract events
!earthevents:ASCA-SIS0-BRIGHT > save events outfile=event.tmp use_events=no
Wrote events list to file event.tmp
!earthevents:ASCA-SIS0-BRIGHT > exit save_session=no
-> Cleaning hot pixels from ad33012010s000202l.unf
-> Standard Output From FTOOL cleansis:
CLEANSIS_V1.6
    allocating image arrays...
 
 PROGRAM TO MAKE AN SIS SCIENCE FILE CLEANED OF ANOMALOUS PIXELS.
 
 * Anomalous pixels may consist of at least two populations.
 
 1. Persistent HOT pixels are removed by comparing to the chip mean.
 
 2. Flickering WARM pixels are removed by comparing to the cell mean.
 
 3. In faint areas (zero bgd), flickering pixels are removed with a
    cutoff threshold.
 
 Hints:
 Choose cell size and thresholds based on the expected background and the PSF.
 Use the DIRTYSIS option to examine the anomalous pixel spectra.
 Try a multiple pass clean:
     Choose a PHA cut to optimize the S/N of the flickering pixels,
     then a broad band clean.
 Be suspicious of extended source cleans.
 For very bright sources you may need to turn off the iteration option.
 
 See the help page for further info (fhelp cleansis)
 
 Poisson clean cell size         :            5
 Poisson probability threshold   :    0.575E-05
 Zero Bgd Cutoff threshold (>)   :            3
 Iterate                         :            F
 Dirtysis                        :            F
 
 Minimum PHA value (inclusive)   :            0
 Maximum PHA value (inclusive)   :         4095
 
    open output  file: ad33012010s000202l.drk
    reading data file: event.tmp
    copying primary header to output file...
    making chip image...
 
 Total counts in chip images :         1142
 
    copy bad pix array...
cleaning chip #           0
cleaning chip #           1
 Hot pixels & counts                   :               3         919
 Flickering pixels iter, pixels & cnts :   1           1           4
cleaning chip #           2
cleaning chip #           3
 
 Number of pixels rejected           :            4
 Number of (internal) image counts   :         1142
 Number of image cts rejected (N, %) :          923     80.8231201
 
         By chip   :             0            1            2            3
 
 Pixels rejected   :             0            4            0            0
 
 Image counts      :             0         1142            0            0
 Image cts rejected:             0          923            0            0
 Image cts rej (%) :          0.00        80.82         0.00         0.00
 
    filtering data...
 
 Total counts      :             0         1142            0            0
 Total cts rejected:             0          923            0            0
 Total cts rej (%) :          0.00        80.82         0.00         0.00
 
 Number of clean counts accepted  :          219
 
    writing history cards...
    copying extensions...
    writing out hot pixs...
 
 Number of rejected pixels        :            4
 
    updating NEVENTS keywords...
    closing data file...
    closing clean file...
-> Extracting bright and dark Earth events from ad33012010s000212l.unf
-> Extracting ad33012010s000212l.drk
-> Standard Output From FTOOL xselect:
 
                         **  XSELECT V1.3   **
 
!> Enter session name >[xsel] earthevents
 
 Notes: XSELECT set up for      ASCA
 Keywords for time and pha are  TIME       PI
 Units of time are              s
 Default timing binsize =    16.00
 Keywords for images are          DETX       DETY
 Keywords for the WMAP are        DETX       DETY
 
 
 
        OBJECT   DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME   NEVENTS  S0CCDPOW
      1 XY_ARI   BRIGHT2  LOW      29/01/96 18:44:15 0.77E+04     2538 0100
 
EXTRACTOR vers 2.0  11 Apr 1997.
 Doing file: /data/data22/seq_proc/33012010.005/ad33012010s000212l.unf
          Total      Good    Bad: Region      Time     Phase       Cut
           2538      1196              0      1342         0         0
 Writing events file
   1196 events written to the output file
===============================================================================
   Grand Total      Good   Bad:  Region      Time     Phase       Cut
          2538      1196              0      1342         0         0
   in    3296.00 seconds
 Command not found; type ? for a command listing
!earthevents:ASCA > set mission ASCA
 
 Notes: XSELECT set up for      ASCA
 Keywords for time and pha are  TIME       PI
 Units of time are              s
 Default timing binsize =    16.00
 Keywords for images are          DETX       DETY
 Keywords for the WMAP are        DETX       DETY
 
!earthevents:ASCA > set datadir .
 
Setting data directory to /data/data22/seq_proc/33012010.005/
Setting mkf directory to /data/data22/seq_proc/33012010.005/
 
!earthevents:ASCA > read events ad33012010s000212l.unf
Got new instrument: SIS0
 
Setting: IMAGE binning    =    4
         WMAP binning     =    8
         Energy Column    =  PI
         Energy rebinning =    1
 
 
Getting Min and Max for Energy Column...
Got min and max for PI:     0   4095
 
Got the minimum time resolution of the read data:   4.0000
 Number of files read in:   1
 
******************** Observation Catalogue ********************
 
Data Directory is: /data/data22/seq_proc/33012010.005/
HK Directory is: /data/data22/seq_proc/33012010.005/
 
!earthevents:ASCA-SIS0-BRIGHT2 > select mkf "FOV==1"  data_dir=. ASCA_mkf_def_expr=ft*.mkf
!earthevents:ASCA-SIS0-BRIGHT2 > extract events
!earthevents:ASCA-SIS0-BRIGHT2 > save events outfile=event.tmp use_events=no
Wrote events list to file event.tmp
!earthevents:ASCA-SIS0-BRIGHT2 > exit save_session=no
-> Cleaning hot pixels from ad33012010s000212l.unf
-> Standard Output From FTOOL cleansis:
CLEANSIS_V1.6
    allocating image arrays...
 
 PROGRAM TO MAKE AN SIS SCIENCE FILE CLEANED OF ANOMALOUS PIXELS.
 
 * Anomalous pixels may consist of at least two populations.
 
 1. Persistent HOT pixels are removed by comparing to the chip mean.
 
 2. Flickering WARM pixels are removed by comparing to the cell mean.
 
 3. In faint areas (zero bgd), flickering pixels are removed with a
    cutoff threshold.
 
 Hints:
 Choose cell size and thresholds based on the expected background and the PSF.
 Use the DIRTYSIS option to examine the anomalous pixel spectra.
 Try a multiple pass clean:
     Choose a PHA cut to optimize the S/N of the flickering pixels,
     then a broad band clean.
 Be suspicious of extended source cleans.
 For very bright sources you may need to turn off the iteration option.
 
 See the help page for further info (fhelp cleansis)
 
 Poisson clean cell size         :            5
 Poisson probability threshold   :    0.575E-05
 Zero Bgd Cutoff threshold (>)   :            3
 Iterate                         :            F
 Dirtysis                        :            F
 
 Minimum PHA value (inclusive)   :            0
 Maximum PHA value (inclusive)   :         4095
 
    open output  file: ad33012010s000212l.drk
    reading data file: event.tmp
    copying primary header to output file...
    making chip image...
 
 Total counts in chip images :         1196
 
    copy bad pix array...
cleaning chip #           0
cleaning chip #           1
 Hot pixels & counts                   :               3         919
 Flickering pixels iter, pixels & cnts :   1           1           4
cleaning chip #           2
cleaning chip #           3
 
 Number of pixels rejected           :            4
 Number of (internal) image counts   :         1196
 Number of image cts rejected (N, %) :          923     77.1739120
 
         By chip   :             0            1            2            3
 
 Pixels rejected   :             0            4            0            0
 
 Image counts      :             0         1196            0            0
 Image cts rejected:             0          923            0            0
 Image cts rej (%) :          0.00        77.17         0.00         0.00
 
    filtering data...
 
 Total counts      :             0         1196            0            0
 Total cts rejected:             0          923            0            0
 Total cts rej (%) :          0.00        77.17         0.00         0.00
 
 Number of clean counts accepted  :          273
 
    writing history cards...
    copying extensions...
    writing out hot pixs...
 
 Number of rejected pixels        :            4
 
    updating NEVENTS keywords...
    closing data file...
    closing clean file...
-> Extracting bright and dark Earth events from ad33012010s000302m.unf
-> Extracting ad33012010s000302m.drk
-> Standard Output From FTOOL xselect:
 
                         **  XSELECT V1.3   **
 
!> Enter session name >[xsel] earthevents
 
 Notes: XSELECT set up for      ASCA
 Keywords for time and pha are  TIME       PI
 Units of time are              s
 Default timing binsize =    16.00
 Keywords for images are          DETX       DETY
 Keywords for the WMAP are        DETX       DETY
 
 
 
        OBJECT   DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME   NEVENTS  S0CCDPOW
      1 XY_ARI   BRIGHT   MEDIUM   29/01/96 17:30:23 0.32E+04     2135 0100
 
EXTRACTOR vers 2.0  11 Apr 1997.
 Skipping file: /data/data22/seq_proc/33012010.005/ad33012010s000302m.unf
 Writing events file
      0 events written to the output file
===============================================================================
   Grand Total      Good   Bad:  Region      Time     Phase       Cut
             0         0              0         0         0         0
   in       0.00 seconds
 Command not found; type ? for a command listing
!earthevents:ASCA > set mission ASCA
 
 Notes: XSELECT set up for      ASCA
 Keywords for time and pha are  TIME       PI
 Units of time are              s
 Default timing binsize =    16.00
 Keywords for images are          DETX       DETY
 Keywords for the WMAP are        DETX       DETY
 
!earthevents:ASCA > set datadir .
 
Setting data directory to /data/data22/seq_proc/33012010.005/
Setting mkf directory to /data/data22/seq_proc/33012010.005/
 
!earthevents:ASCA > read events ad33012010s000302m.unf
Got new instrument: SIS0
 
Setting: IMAGE binning    =    4
         WMAP binning     =    8
         Energy Column    =  PI
         Energy rebinning =    1
 
 
Getting Min and Max for Energy Column...
Got min and max for PI:     0   2047
 
Got the minimum time resolution of the read data:   4.0000
 Number of files read in:   1
 
******************** Observation Catalogue ********************
 
Data Directory is: /data/data22/seq_proc/33012010.005/
HK Directory is: /data/data22/seq_proc/33012010.005/
 
!earthevents:ASCA-SIS0-BRIGHT > select mkf "FOV==1"  data_dir=. ASCA_mkf_def_expr=ft*.mkf
!earthevents:ASCA-SIS0-BRIGHT > extract events
!earthevents:ASCA-SIS0-BRIGHT > save events outfile=event.tmp use_events=no
Wrote events list to file event.tmp
!earthevents:ASCA-SIS0-BRIGHT > exit save_session=no
-> Deleting ad33012010s000302m.drk since it contains 0 events
-> Extracting bright and dark Earth events from ad33012010s000312m.unf
-> Extracting ad33012010s000312m.drk
-> Standard Output From FTOOL xselect:
 
                         **  XSELECT V1.3   **
 
!> Enter session name >[xsel] earthevents
 
 Notes: XSELECT set up for      ASCA
 Keywords for time and pha are  TIME       PI
 Units of time are              s
 Default timing binsize =    16.00
 Keywords for images are          DETX       DETY
 Keywords for the WMAP are        DETX       DETY
 
 
 
        OBJECT   DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME   NEVENTS  S0CCDPOW
      1 XY_ARI   BRIGHT2  MEDIUM   29/01/96 17:30:23 0.32E+04     2201 0100
 
EXTRACTOR vers 2.0  11 Apr 1997.
 Skipping file: /data/data22/seq_proc/33012010.005/ad33012010s000312m.unf
 Writing events file
      0 events written to the output file
===============================================================================
   Grand Total      Good   Bad:  Region      Time     Phase       Cut
             0         0              0         0         0         0
   in       0.00 seconds
 Command not found; type ? for a command listing
!earthevents:ASCA > set mission ASCA
 
 Notes: XSELECT set up for      ASCA
 Keywords for time and pha are  TIME       PI
 Units of time are              s
 Default timing binsize =    16.00
 Keywords for images are          DETX       DETY
 Keywords for the WMAP are        DETX       DETY
 
!earthevents:ASCA > set datadir .
 
Setting data directory to /data/data22/seq_proc/33012010.005/
Setting mkf directory to /data/data22/seq_proc/33012010.005/
 
!earthevents:ASCA > read events ad33012010s000312m.unf
Got new instrument: SIS0
 
Setting: IMAGE binning    =    4
         WMAP binning     =    8
         Energy Column    =  PI
         Energy rebinning =    1
 
 
Getting Min and Max for Energy Column...
Got min and max for PI:     0   4095
 
Got the minimum time resolution of the read data:   4.0000
 Number of files read in:   1
 
******************** Observation Catalogue ********************
 
Data Directory is: /data/data22/seq_proc/33012010.005/
HK Directory is: /data/data22/seq_proc/33012010.005/
 
!earthevents:ASCA-SIS0-BRIGHT2 > select mkf "FOV==1"  data_dir=. ASCA_mkf_def_expr=ft*.mkf
!earthevents:ASCA-SIS0-BRIGHT2 > extract events
!earthevents:ASCA-SIS0-BRIGHT2 > save events outfile=event.tmp use_events=no
Wrote events list to file event.tmp
!earthevents:ASCA-SIS0-BRIGHT2 > exit save_session=no
-> Deleting ad33012010s000312m.drk since it contains 0 events
-> Extracting bright and dark Earth events from ad33012010s100102h.unf
-> Extracting ad33012010s100102h.drk
-> Standard Output From FTOOL xselect:
 
                         **  XSELECT V1.3   **
 
!> Enter session name >[xsel] earthevents
 
 Notes: XSELECT set up for      ASCA
 Keywords for time and pha are  TIME       PI
 Units of time are              s
 Default timing binsize =    16.00
 Keywords for images are          DETX       DETY
 Keywords for the WMAP are        DETX       DETY
 
 
 
        OBJECT   DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME   NEVENTS  S1CCDPOW
      1 XY_ARI   BRIGHT   HIGH     29/01/96 17:42:55 0.55E+04     8800 0001
 
EXTRACTOR vers 2.0  11 Apr 1997.
 Skipping file: /data/data22/seq_proc/33012010.005/ad33012010s100102h.unf
 Writing events file
      0 events written to the output file
===============================================================================
   Grand Total      Good   Bad:  Region      Time     Phase       Cut
             0         0              0         0         0         0
   in       0.00 seconds
 Command not found; type ? for a command listing
!earthevents:ASCA > set mission ASCA
 
 Notes: XSELECT set up for      ASCA
 Keywords for time and pha are  TIME       PI
 Units of time are              s
 Default timing binsize =    16.00
 Keywords for images are          DETX       DETY
 Keywords for the WMAP are        DETX       DETY
 
!earthevents:ASCA > set datadir .
 
Setting data directory to /data/data22/seq_proc/33012010.005/
Setting mkf directory to /data/data22/seq_proc/33012010.005/
 
!earthevents:ASCA > read events ad33012010s100102h.unf
Got new instrument: SIS1
 
Setting: IMAGE binning    =    4
         WMAP binning     =    8
         Energy Column    =  PI
         Energy rebinning =    1
 
 
Getting Min and Max for Energy Column...
Got min and max for PI:     0   2047
 
Got the minimum time resolution of the read data:   4.0000
 Number of files read in:   1
 
******************** Observation Catalogue ********************
 
Data Directory is: /data/data22/seq_proc/33012010.005/
HK Directory is: /data/data22/seq_proc/33012010.005/
 
!earthevents:ASCA-SIS1-BRIGHT > select mkf "FOV==1"  data_dir=. ASCA_mkf_def_expr=ft*.mkf
!earthevents:ASCA-SIS1-BRIGHT > extract events
!earthevents:ASCA-SIS1-BRIGHT > save events outfile=event.tmp use_events=no
Wrote events list to file event.tmp
!earthevents:ASCA-SIS1-BRIGHT > exit save_session=no
-> Deleting ad33012010s100102h.drk since it contains 0 events
-> Extracting bright and dark Earth events from ad33012010s100112h.unf
-> Extracting ad33012010s100112h.drk
-> Standard Output From FTOOL xselect:
 
                         **  XSELECT V1.3   **
 
!> Enter session name >[xsel] earthevents
 
 Notes: XSELECT set up for      ASCA
 Keywords for time and pha are  TIME       PI
 Units of time are              s
 Default timing binsize =    16.00
 Keywords for images are          DETX       DETY
 Keywords for the WMAP are        DETX       DETY
 
 
 
        OBJECT   DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME   NEVENTS  S1CCDPOW
      1 XY_ARI   BRIGHT2  HIGH     29/01/96 17:42:55 0.55E+04     8919 0001
 
EXTRACTOR vers 2.0  11 Apr 1997.
 Skipping file: /data/data22/seq_proc/33012010.005/ad33012010s100112h.unf
 Writing events file
      0 events written to the output file
===============================================================================
   Grand Total      Good   Bad:  Region      Time     Phase       Cut
             0         0              0         0         0         0
   in       0.00 seconds
 Command not found; type ? for a command listing
!earthevents:ASCA > set mission ASCA
 
 Notes: XSELECT set up for      ASCA
 Keywords for time and pha are  TIME       PI
 Units of time are              s
 Default timing binsize =    16.00
 Keywords for images are          DETX       DETY
 Keywords for the WMAP are        DETX       DETY
 
!earthevents:ASCA > set datadir .
 
Setting data directory to /data/data22/seq_proc/33012010.005/
Setting mkf directory to /data/data22/seq_proc/33012010.005/
 
!earthevents:ASCA > read events ad33012010s100112h.unf
Got new instrument: SIS1
 
Setting: IMAGE binning    =    4
         WMAP binning     =    8
         Energy Column    =  PI
         Energy rebinning =    1
 
 
Getting Min and Max for Energy Column...
Got min and max for PI:     0   4095
 
Got the minimum time resolution of the read data:   4.0000
 Number of files read in:   1
 
******************** Observation Catalogue ********************
 
Data Directory is: /data/data22/seq_proc/33012010.005/
HK Directory is: /data/data22/seq_proc/33012010.005/
 
!earthevents:ASCA-SIS1-BRIGHT2 > select mkf "FOV==1"  data_dir=. ASCA_mkf_def_expr=ft*.mkf
!earthevents:ASCA-SIS1-BRIGHT2 > extract events
!earthevents:ASCA-SIS1-BRIGHT2 > save events outfile=event.tmp use_events=no
Wrote events list to file event.tmp
!earthevents:ASCA-SIS1-BRIGHT2 > exit save_session=no
-> Deleting ad33012010s100112h.drk since it contains 0 events
-> Extracting bright and dark Earth events from ad33012010s100202l.unf
-> Extracting ad33012010s100202l.drk
-> Standard Output From FTOOL xselect:
 
                         **  XSELECT V1.3   **
 
!> Enter session name >[xsel] earthevents
 
 Notes: XSELECT set up for      ASCA
 Keywords for time and pha are  TIME       PI
 Units of time are              s
 Default timing binsize =    16.00
 Keywords for images are          DETX       DETY
 Keywords for the WMAP are        DETX       DETY
 
 
 
        OBJECT   DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME   NEVENTS  S1CCDPOW
      1 XY_ARI   BRIGHT   LOW      29/01/96 18:44:15 0.77E+04     7079 0001
 
EXTRACTOR vers 2.0  11 Apr 1997.
 Doing file: /data/data22/seq_proc/33012010.005/ad33012010s100202l.unf
          Total      Good    Bad: Region      Time     Phase       Cut
           7079      3174              0      3905         0         0
 Writing events file
   3174 events written to the output file
===============================================================================
   Grand Total      Good   Bad:  Region      Time     Phase       Cut
          7079      3174              0      3905         0         0
   in    3296.00 seconds
 Command not found; type ? for a command listing
!earthevents:ASCA > set mission ASCA
 
 Notes: XSELECT set up for      ASCA
 Keywords for time and pha are  TIME       PI
 Units of time are              s
 Default timing binsize =    16.00
 Keywords for images are          DETX       DETY
 Keywords for the WMAP are        DETX       DETY
 
!earthevents:ASCA > set datadir .
 
Setting data directory to /data/data22/seq_proc/33012010.005/
Setting mkf directory to /data/data22/seq_proc/33012010.005/
 
!earthevents:ASCA > read events ad33012010s100202l.unf
Got new instrument: SIS1
 
Setting: IMAGE binning    =    4
         WMAP binning     =    8
         Energy Column    =  PI
         Energy rebinning =    1
 
 
Getting Min and Max for Energy Column...
Got min and max for PI:     0   2047
 
Got the minimum time resolution of the read data:   4.0000
 Number of files read in:   1
 
******************** Observation Catalogue ********************
 
Data Directory is: /data/data22/seq_proc/33012010.005/
HK Directory is: /data/data22/seq_proc/33012010.005/
 
!earthevents:ASCA-SIS1-BRIGHT > select mkf "FOV==1"  data_dir=. ASCA_mkf_def_expr=ft*.mkf
!earthevents:ASCA-SIS1-BRIGHT > extract events
!earthevents:ASCA-SIS1-BRIGHT > save events outfile=event.tmp use_events=no
Wrote events list to file event.tmp
!earthevents:ASCA-SIS1-BRIGHT > exit save_session=no
-> Cleaning hot pixels from ad33012010s100202l.unf
-> Standard Output From FTOOL cleansis:
CLEANSIS_V1.6
    allocating image arrays...
 
 PROGRAM TO MAKE AN SIS SCIENCE FILE CLEANED OF ANOMALOUS PIXELS.
 
 * Anomalous pixels may consist of at least two populations.
 
 1. Persistent HOT pixels are removed by comparing to the chip mean.
 
 2. Flickering WARM pixels are removed by comparing to the cell mean.
 
 3. In faint areas (zero bgd), flickering pixels are removed with a
    cutoff threshold.
 
 Hints:
 Choose cell size and thresholds based on the expected background and the PSF.
 Use the DIRTYSIS option to examine the anomalous pixel spectra.
 Try a multiple pass clean:
     Choose a PHA cut to optimize the S/N of the flickering pixels,
     then a broad band clean.
 Be suspicious of extended source cleans.
 For very bright sources you may need to turn off the iteration option.
 
 See the help page for further info (fhelp cleansis)
 
 Poisson clean cell size         :            5
 Poisson probability threshold   :    0.575E-05
 Zero Bgd Cutoff threshold (>)   :            3
 Iterate                         :            F
 Dirtysis                        :            F
 
 Minimum PHA value (inclusive)   :            0
 Maximum PHA value (inclusive)   :         4095
 
    open output  file: ad33012010s100202l.drk
    reading data file: event.tmp
    copying primary header to output file...
    making chip image...
 
 Total counts in chip images :         3174
 
    copy bad pix array...
cleaning chip #           0
cleaning chip #           1
cleaning chip #           2
cleaning chip #           3
 Hot pixels & counts                   :               8        2994
 Flickering pixels iter, pixels & cnts :   1           2          12
 
 Number of pixels rejected           :           10
 Number of (internal) image counts   :         3174
 Number of image cts rejected (N, %) :         3006     94.7069931
 
         By chip   :             0            1            2            3
 
 Pixels rejected   :             0            0            0           10
 
 Image counts      :             0            0            0         3174
 Image cts rejected:             0            0            0         3006
 Image cts rej (%) :          0.00         0.00         0.00        94.71
 
    filtering data...
 
 Total counts      :             0            0            0         3174
 Total cts rejected:             0            0            0         3006
 Total cts rej (%) :          0.00         0.00         0.00        94.71
 
 Number of clean counts accepted  :          168
 
    writing history cards...
    copying extensions...
    writing out hot pixs...
 
 Number of rejected pixels        :           10
 
    updating NEVENTS keywords...
    closing data file...
    closing clean file...
-> Extracting bright and dark Earth events from ad33012010s100212l.unf
-> Extracting ad33012010s100212l.drk
-> Standard Output From FTOOL xselect:
 
                         **  XSELECT V1.3   **
 
!> Enter session name >[xsel] earthevents
 
 Notes: XSELECT set up for      ASCA
 Keywords for time and pha are  TIME       PI
 Units of time are              s
 Default timing binsize =    16.00
 Keywords for images are          DETX       DETY
 Keywords for the WMAP are        DETX       DETY
 
 
 
        OBJECT   DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME   NEVENTS  S1CCDPOW
      1 XY_ARI   BRIGHT2  LOW      29/01/96 18:44:15 0.77E+04     7137 0001
 
EXTRACTOR vers 2.0  11 Apr 1997.
 Doing file: /data/data22/seq_proc/33012010.005/ad33012010s100212l.unf
          Total      Good    Bad: Region      Time     Phase       Cut
           7137      3209              0      3928         0         0
 Writing events file
   3209 events written to the output file
===============================================================================
   Grand Total      Good   Bad:  Region      Time     Phase       Cut
          7137      3209              0      3928         0         0
   in    3296.00 seconds
 Command not found; type ? for a command listing
!earthevents:ASCA > set mission ASCA
 
 Notes: XSELECT set up for      ASCA
 Keywords for time and pha are  TIME       PI
 Units of time are              s
 Default timing binsize =    16.00
 Keywords for images are          DETX       DETY
 Keywords for the WMAP are        DETX       DETY
 
!earthevents:ASCA > set datadir .
 
Setting data directory to /data/data22/seq_proc/33012010.005/
Setting mkf directory to /data/data22/seq_proc/33012010.005/
 
!earthevents:ASCA > read events ad33012010s100212l.unf
Got new instrument: SIS1
 
Setting: IMAGE binning    =    4
         WMAP binning     =    8
         Energy Column    =  PI
         Energy rebinning =    1
 
 
Getting Min and Max for Energy Column...
Got min and max for PI:     0   4095
 
Got the minimum time resolution of the read data:   4.0000
 Number of files read in:   1
 
******************** Observation Catalogue ********************
 
Data Directory is: /data/data22/seq_proc/33012010.005/
HK Directory is: /data/data22/seq_proc/33012010.005/
 
!earthevents:ASCA-SIS1-BRIGHT2 > select mkf "FOV==1"  data_dir=. ASCA_mkf_def_expr=ft*.mkf
!earthevents:ASCA-SIS1-BRIGHT2 > extract events
!earthevents:ASCA-SIS1-BRIGHT2 > save events outfile=event.tmp use_events=no
Wrote events list to file event.tmp
!earthevents:ASCA-SIS1-BRIGHT2 > exit save_session=no
-> Cleaning hot pixels from ad33012010s100212l.unf
-> Standard Output From FTOOL cleansis:
CLEANSIS_V1.6
    allocating image arrays...
 
 PROGRAM TO MAKE AN SIS SCIENCE FILE CLEANED OF ANOMALOUS PIXELS.
 
 * Anomalous pixels may consist of at least two populations.
 
 1. Persistent HOT pixels are removed by comparing to the chip mean.
 
 2. Flickering WARM pixels are removed by comparing to the cell mean.
 
 3. In faint areas (zero bgd), flickering pixels are removed with a
    cutoff threshold.
 
 Hints:
 Choose cell size and thresholds based on the expected background and the PSF.
 Use the DIRTYSIS option to examine the anomalous pixel spectra.
 Try a multiple pass clean:
     Choose a PHA cut to optimize the S/N of the flickering pixels,
     then a broad band clean.
 Be suspicious of extended source cleans.
 For very bright sources you may need to turn off the iteration option.
 
 See the help page for further info (fhelp cleansis)
 
 Poisson clean cell size         :            5
 Poisson probability threshold   :    0.575E-05
 Zero Bgd Cutoff threshold (>)   :            3
 Iterate                         :            F
 Dirtysis                        :            F
 
 Minimum PHA value (inclusive)   :            0
 Maximum PHA value (inclusive)   :         4095
 
    open output  file: ad33012010s100212l.drk
    reading data file: event.tmp
    copying primary header to output file...
    making chip image...
 
 Total counts in chip images :         3209
 
    copy bad pix array...
cleaning chip #           0
cleaning chip #           1
cleaning chip #           2
cleaning chip #           3
 Hot pixels & counts                   :               8        2994
 Flickering pixels iter, pixels & cnts :   1           2          12
 
 Number of pixels rejected           :           10
 Number of (internal) image counts   :         3209
 Number of image cts rejected (N, %) :         3006     93.6740417
 
         By chip   :             0            1            2            3
 
 Pixels rejected   :             0            0            0           10
 
 Image counts      :             0            0            0         3209
 Image cts rejected:             0            0            0         3006
 Image cts rej (%) :          0.00         0.00         0.00        93.67
 
    filtering data...
 
 Total counts      :             0            0            0         3209
 Total cts rejected:             0            0            0         3006
 Total cts rej (%) :          0.00         0.00         0.00        93.67
 
 Number of clean counts accepted  :          203
 
    writing history cards...
    copying extensions...
    writing out hot pixs...
 
 Number of rejected pixels        :           10
 
    updating NEVENTS keywords...
    closing data file...
    closing clean file...
-> Extracting bright and dark Earth events from ad33012010s100302m.unf
-> Extracting ad33012010s100302m.drk
-> Standard Output From FTOOL xselect:
 
                         **  XSELECT V1.3   **
 
!> Enter session name >[xsel] earthevents
 
 Notes: XSELECT set up for      ASCA
 Keywords for time and pha are  TIME       PI
 Units of time are              s
 Default timing binsize =    16.00
 Keywords for images are          DETX       DETY
 Keywords for the WMAP are        DETX       DETY
 
 
 
        OBJECT   DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME   NEVENTS  S1CCDPOW
      1 XY_ARI   BRIGHT   MEDIUM   29/01/96 17:30:23 0.32E+04     4520 0001
 
EXTRACTOR vers 2.0  11 Apr 1997.
 Skipping file: /data/data22/seq_proc/33012010.005/ad33012010s100302m.unf
 Writing events file
      0 events written to the output file
===============================================================================
   Grand Total      Good   Bad:  Region      Time     Phase       Cut
             0         0              0         0         0         0
   in       0.00 seconds
 Command not found; type ? for a command listing
!earthevents:ASCA > set mission ASCA
 
 Notes: XSELECT set up for      ASCA
 Keywords for time and pha are  TIME       PI
 Units of time are              s
 Default timing binsize =    16.00
 Keywords for images are          DETX       DETY
 Keywords for the WMAP are        DETX       DETY
 
!earthevents:ASCA > set datadir .
 
Setting data directory to /data/data22/seq_proc/33012010.005/
Setting mkf directory to /data/data22/seq_proc/33012010.005/
 
!earthevents:ASCA > read events ad33012010s100302m.unf
Got new instrument: SIS1
 
Setting: IMAGE binning    =    4
         WMAP binning     =    8
         Energy Column    =  PI
         Energy rebinning =    1
 
 
Getting Min and Max for Energy Column...
Got min and max for PI:     0   2047
 
Got the minimum time resolution of the read data:   4.0000
 Number of files read in:   1
 
******************** Observation Catalogue ********************
 
Data Directory is: /data/data22/seq_proc/33012010.005/
HK Directory is: /data/data22/seq_proc/33012010.005/
 
!earthevents:ASCA-SIS1-BRIGHT > select mkf "FOV==1"  data_dir=. ASCA_mkf_def_expr=ft*.mkf
!earthevents:ASCA-SIS1-BRIGHT > extract events
!earthevents:ASCA-SIS1-BRIGHT > save events outfile=event.tmp use_events=no
Wrote events list to file event.tmp
!earthevents:ASCA-SIS1-BRIGHT > exit save_session=no
-> Deleting ad33012010s100302m.drk since it contains 0 events
-> Extracting bright and dark Earth events from ad33012010s100312m.unf
-> Extracting ad33012010s100312m.drk
-> Standard Output From FTOOL xselect:
 
                         **  XSELECT V1.3   **
 
!> Enter session name >[xsel] earthevents
 
 Notes: XSELECT set up for      ASCA
 Keywords for time and pha are  TIME       PI
 Units of time are              s
 Default timing binsize =    16.00
 Keywords for images are          DETX       DETY
 Keywords for the WMAP are        DETX       DETY
 
 
 
        OBJECT   DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME   NEVENTS  S1CCDPOW
      1 XY_ARI   BRIGHT2  MEDIUM   29/01/96 17:30:23 0.32E+04     4559 0001
 
EXTRACTOR vers 2.0  11 Apr 1997.
 Skipping file: /data/data22/seq_proc/33012010.005/ad33012010s100312m.unf
 Writing events file
      0 events written to the output file
===============================================================================
   Grand Total      Good   Bad:  Region      Time     Phase       Cut
             0         0              0         0         0         0
   in       0.00 seconds
 Command not found; type ? for a command listing
!earthevents:ASCA > set mission ASCA
 
 Notes: XSELECT set up for      ASCA
 Keywords for time and pha are  TIME       PI
 Units of time are              s
 Default timing binsize =    16.00
 Keywords for images are          DETX       DETY
 Keywords for the WMAP are        DETX       DETY
 
!earthevents:ASCA > set datadir .
 
Setting data directory to /data/data22/seq_proc/33012010.005/
Setting mkf directory to /data/data22/seq_proc/33012010.005/
 
!earthevents:ASCA > read events ad33012010s100312m.unf
Got new instrument: SIS1
 
Setting: IMAGE binning    =    4
         WMAP binning     =    8
         Energy Column    =  PI
         Energy rebinning =    1
 
 
Getting Min and Max for Energy Column...
Got min and max for PI:     0   4095
 
Got the minimum time resolution of the read data:   4.0000
 Number of files read in:   1
 
******************** Observation Catalogue ********************
 
Data Directory is: /data/data22/seq_proc/33012010.005/
HK Directory is: /data/data22/seq_proc/33012010.005/
 
!earthevents:ASCA-SIS1-BRIGHT2 > select mkf "FOV==1"  data_dir=. ASCA_mkf_def_expr=ft*.mkf
!earthevents:ASCA-SIS1-BRIGHT2 > extract events
!earthevents:ASCA-SIS1-BRIGHT2 > save events outfile=event.tmp use_events=no
Wrote events list to file event.tmp
!earthevents:ASCA-SIS1-BRIGHT2 > exit save_session=no
-> Deleting ad33012010s100312m.drk since it contains 0 events
-> Extracting bright and dark Earth events from ad33012010g200170h.unf
-> Extracting ad33012010g200170h.drk
-> Standard Output From FTOOL xselect:
 
                         **  XSELECT V1.3   **
 
!> Enter session name >[xsel] earthevents
 
 Notes: XSELECT set up for      ASCA
 Keywords for time and pha are  TIME       PI
 Units of time are              s
 Default timing binsize =    16.00
 Keywords for images are          DETX       DETY
 Keywords for the WMAP are        DETX       DETY
 
 
 
        OBJECT   DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME   NEVENTS  PHA_BINS
      1 XY_ARI   PH       HIGH     29/01/96 17:43:01 0.48E+04     4638     1024
 
EXTRACTOR vers 2.0  11 Apr 1997.
 Skipping file: /data/data22/seq_proc/33012010.005/ad33012010g200170h.unf
 Writing events file
      0 events written to the output file
===============================================================================
   Grand Total      Good   Bad:  Region      Time     Phase       Cut
             0         0              0         0         0         0
   in       0.00 seconds
 Command not found; type ? for a command listing
!earthevents:ASCA > set mission ASCA
 
 Notes: XSELECT set up for      ASCA
 Keywords for time and pha are  TIME       PI
 Units of time are              s
 Default timing binsize =    16.00
 Keywords for images are          DETX       DETY
 Keywords for the WMAP are        DETX       DETY
 
!earthevents:ASCA > set datadir .
 
Setting data directory to /data/data22/seq_proc/33012010.005/
Setting mkf directory to /data/data22/seq_proc/33012010.005/
 
!earthevents:ASCA > read events ad33012010g200170h.unf
Got new instrument: GIS2
 
Setting: IMAGE binning    =    1
         WMAP binning     =    1
         Energy Column    =  PI
         Energy rebinning =    1
 
 
Getting Min and Max for Energy Column...
Got min and max for PI:     0   1023
 
Got the minimum time resolution of the read data:  0.62500E-01
 Number of files read in:   1
 
******************** Observation Catalogue ********************
 
Data Directory is: /data/data22/seq_proc/33012010.005/
HK Directory is: /data/data22/seq_proc/33012010.005/
 
!earthevents:ASCA-GIS2-PH > select mkf "FOV==1"  data_dir=. ASCA_mkf_def_expr=ft*.mkf
!earthevents:ASCA-GIS2-PH > extract events
!earthevents:ASCA-GIS2-PH > save events outfile=event.tmp use_events=no
Wrote events list to file event.tmp
!earthevents:ASCA-GIS2-PH > exit save_session=no
-> Deleting ad33012010g200170h.drk since it contains 0 events
-> Extracting ad33012010g200170h.brt
-> Standard Output From FTOOL xselect:
 
                         **  XSELECT V1.3   **
 
!> Enter session name >[xsel] earthevents
 
 Notes: XSELECT set up for      ASCA
 Keywords for time and pha are  TIME       PI
 Units of time are              s
 Default timing binsize =    16.00
 Keywords for images are          DETX       DETY
 Keywords for the WMAP are        DETX       DETY
 
 
 
        OBJECT   DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME   NEVENTS  PHA_BINS
      1 XY_ARI   PH       HIGH     29/01/96 17:43:01 0.48E+04     4638     1024
 
EXTRACTOR vers 2.0  11 Apr 1997.
 Doing file: /data/data22/seq_proc/33012010.005/ad33012010g200170h.unf
          Total      Good    Bad: Region      Time     Phase       Cut
           4638        69              0      4569         0         0
 Writing events file
     69 events written to the output file
===============================================================================
   Grand Total      Good   Bad:  Region      Time     Phase       Cut
          4638        69              0      4569         0         0
   in      92.00 seconds
 Command not found; type ? for a command listing
!earthevents:ASCA > set mission ASCA
 
 Notes: XSELECT set up for      ASCA
 Keywords for time and pha are  TIME       PI
 Units of time are              s
 Default timing binsize =    16.00
 Keywords for images are          DETX       DETY
 Keywords for the WMAP are        DETX       DETY
 
!earthevents:ASCA > set datadir .
 
Setting data directory to /data/data22/seq_proc/33012010.005/
Setting mkf directory to /data/data22/seq_proc/33012010.005/
 
!earthevents:ASCA > read events ad33012010g200170h.unf
Got new instrument: GIS2
 
Setting: IMAGE binning    =    1
         WMAP binning     =    1
         Energy Column    =  PI
         Energy rebinning =    1
 
 
Getting Min and Max for Energy Column...
Got min and max for PI:     0   1023
 
Got the minimum time resolution of the read data:  0.62500E-01
 Number of files read in:   1
 
******************** Observation Catalogue ********************
 
Data Directory is: /data/data22/seq_proc/33012010.005/
HK Directory is: /data/data22/seq_proc/33012010.005/
 
!earthevents:ASCA-GIS2-PH > select mkf "FOV==2"  data_dir=. ASCA_mkf_def_expr=ft*.mkf
!earthevents:ASCA-GIS2-PH > extract events
!earthevents:ASCA-GIS2-PH > save events outfile=event.tmp use_events=no
Wrote events list to file event.tmp
!earthevents:ASCA-GIS2-PH > exit save_session=no
-> Extracting bright and dark Earth events from ad33012010g200270l.unf
-> Extracting ad33012010g200270l.drk
-> Standard Output From FTOOL xselect:
 
                         **  XSELECT V1.3   **
 
!> Enter session name >[xsel] earthevents
 
 Notes: XSELECT set up for      ASCA
 Keywords for time and pha are  TIME       PI
 Units of time are              s
 Default timing binsize =    16.00
 Keywords for images are          DETX       DETY
 Keywords for the WMAP are        DETX       DETY
 
 
 
        OBJECT   DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME   NEVENTS  PHA_BINS
      1 XY_ARI   PH       LOW      29/01/96 18:46:29 0.61E+04     3925     1024
 
EXTRACTOR vers 2.0  11 Apr 1997.
 Doing file: /data/data22/seq_proc/33012010.005/ad33012010g200270l.unf
          Total      Good    Bad: Region      Time     Phase       Cut
           3925      2044              0      1881         0         0
 Writing events file
   2044 events written to the output file
===============================================================================
   Grand Total      Good   Bad:  Region      Time     Phase       Cut
          3925      2044              0      1881         0         0
   in    2816.09 seconds
 Command not found; type ? for a command listing
!earthevents:ASCA > set mission ASCA
 
 Notes: XSELECT set up for      ASCA
 Keywords for time and pha are  TIME       PI
 Units of time are              s
 Default timing binsize =    16.00
 Keywords for images are          DETX       DETY
 Keywords for the WMAP are        DETX       DETY
 
!earthevents:ASCA > set datadir .
 
Setting data directory to /data/data22/seq_proc/33012010.005/
Setting mkf directory to /data/data22/seq_proc/33012010.005/
 
!earthevents:ASCA > read events ad33012010g200270l.unf
Got new instrument: GIS2
 
Setting: IMAGE binning    =    1
         WMAP binning     =    1
         Energy Column    =  PI
         Energy rebinning =    1
 
 
Getting Min and Max for Energy Column...
Got min and max for PI:     0   1023
 
Got the minimum time resolution of the read data:   2.0000
 Number of files read in:   1
 
******************** Observation Catalogue ********************
 
Data Directory is: /data/data22/seq_proc/33012010.005/
HK Directory is: /data/data22/seq_proc/33012010.005/
 
!earthevents:ASCA-GIS2-PH > select mkf "FOV==1"  data_dir=. ASCA_mkf_def_expr=ft*.mkf
!earthevents:ASCA-GIS2-PH > extract events
!earthevents:ASCA-GIS2-PH > save events outfile=event.tmp use_events=no
Wrote events list to file event.tmp
!earthevents:ASCA-GIS2-PH > exit save_session=no
-> Extracting ad33012010g200270l.brt
-> Standard Output From FTOOL xselect:
 
                         **  XSELECT V1.3   **
 
!> Enter session name >[xsel] earthevents
 
 Notes: XSELECT set up for      ASCA
 Keywords for time and pha are  TIME       PI
 Units of time are              s
 Default timing binsize =    16.00
 Keywords for images are          DETX       DETY
 Keywords for the WMAP are        DETX       DETY
 
 
 
        OBJECT   DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME   NEVENTS  PHA_BINS
      1 XY_ARI   PH       LOW      29/01/96 18:46:29 0.61E+04     3925     1024
 
EXTRACTOR vers 2.0  11 Apr 1997.
 Doing file: /data/data22/seq_proc/33012010.005/ad33012010g200270l.unf
          Total      Good    Bad: Region      Time     Phase       Cut
           3925      1657              0      2268         0         0
 Writing events file
   1657 events written to the output file
===============================================================================
   Grand Total      Good   Bad:  Region      Time     Phase       Cut
          3925      1657              0      2268         0         0
   in    3072.00 seconds
 Command not found; type ? for a command listing
!earthevents:ASCA > set mission ASCA
 
 Notes: XSELECT set up for      ASCA
 Keywords for time and pha are  TIME       PI
 Units of time are              s
 Default timing binsize =    16.00
 Keywords for images are          DETX       DETY
 Keywords for the WMAP are        DETX       DETY
 
!earthevents:ASCA > set datadir .
 
Setting data directory to /data/data22/seq_proc/33012010.005/
Setting mkf directory to /data/data22/seq_proc/33012010.005/
 
!earthevents:ASCA > read events ad33012010g200270l.unf
Got new instrument: GIS2
 
Setting: IMAGE binning    =    1
         WMAP binning     =    1
         Energy Column    =  PI
         Energy rebinning =    1
 
 
Getting Min and Max for Energy Column...
Got min and max for PI:     0   1023
 
Got the minimum time resolution of the read data:   2.0000
 Number of files read in:   1
 
******************** Observation Catalogue ********************
 
Data Directory is: /data/data22/seq_proc/33012010.005/
HK Directory is: /data/data22/seq_proc/33012010.005/
 
!earthevents:ASCA-GIS2-PH > select mkf "FOV==2"  data_dir=. ASCA_mkf_def_expr=ft*.mkf
!earthevents:ASCA-GIS2-PH > extract events
!earthevents:ASCA-GIS2-PH > save events outfile=event.tmp use_events=no
Wrote events list to file event.tmp
!earthevents:ASCA-GIS2-PH > exit save_session=no
-> Extracting bright and dark Earth events from ad33012010g200370m.unf
-> Extracting ad33012010g200370m.drk
-> Standard Output From FTOOL xselect:
 
                         **  XSELECT V1.3   **
 
!> Enter session name >[xsel] earthevents
 
 Notes: XSELECT set up for      ASCA
 Keywords for time and pha are  TIME       PI
 Units of time are              s
 Default timing binsize =    16.00
 Keywords for images are          DETX       DETY
 Keywords for the WMAP are        DETX       DETY
 
 
 
        OBJECT   DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME   NEVENTS  PHA_BINS
      1 XY_ARI   PH       MEDIUM   29/01/96 17:30:29 0.33E+04     2903     1024
 
EXTRACTOR vers 2.0  11 Apr 1997.
 Skipping file: /data/data22/seq_proc/33012010.005/ad33012010g200370m.unf
 Writing events file
      0 events written to the output file
===============================================================================
   Grand Total      Good   Bad:  Region      Time     Phase       Cut
             0         0              0         0         0         0
   in       0.00 seconds
 Command not found; type ? for a command listing
!earthevents:ASCA > set mission ASCA
 
 Notes: XSELECT set up for      ASCA
 Keywords for time and pha are  TIME       PI
 Units of time are              s
 Default timing binsize =    16.00
 Keywords for images are          DETX       DETY
 Keywords for the WMAP are        DETX       DETY
 
!earthevents:ASCA > set datadir .
 
Setting data directory to /data/data22/seq_proc/33012010.005/
Setting mkf directory to /data/data22/seq_proc/33012010.005/
 
!earthevents:ASCA > read events ad33012010g200370m.unf
Got new instrument: GIS2
 
Setting: IMAGE binning    =    1
         WMAP binning     =    1
         Energy Column    =  PI
         Energy rebinning =    1
 
 
Getting Min and Max for Energy Column...
Got min and max for PI:     0   1023
 
Got the minimum time resolution of the read data:  0.50000
 Number of files read in:   1
 
******************** Observation Catalogue ********************
 
Data Directory is: /data/data22/seq_proc/33012010.005/
HK Directory is: /data/data22/seq_proc/33012010.005/
 
!earthevents:ASCA-GIS2-PH > select mkf "FOV==1"  data_dir=. ASCA_mkf_def_expr=ft*.mkf
!earthevents:ASCA-GIS2-PH > extract events
!earthevents:ASCA-GIS2-PH > save events outfile=event.tmp use_events=no
Wrote events list to file event.tmp
!earthevents:ASCA-GIS2-PH > exit save_session=no
-> Deleting ad33012010g200370m.drk since it contains 0 events
-> Extracting ad33012010g200370m.brt
-> Standard Output From FTOOL xselect:
 
                         **  XSELECT V1.3   **
 
!> Enter session name >[xsel] earthevents
 
 Notes: XSELECT set up for      ASCA
 Keywords for time and pha are  TIME       PI
 Units of time are              s
 Default timing binsize =    16.00
 Keywords for images are          DETX       DETY
 Keywords for the WMAP are        DETX       DETY
 
 
 
        OBJECT   DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME   NEVENTS  PHA_BINS
      1 XY_ARI   PH       MEDIUM   29/01/96 17:30:29 0.33E+04     2903     1024
 
EXTRACTOR vers 2.0  11 Apr 1997.
 Doing file: /data/data22/seq_proc/33012010.005/ad33012010g200370m.unf
          Total      Good    Bad: Region      Time     Phase       Cut
           2903       436              0      2467         0         0
 Writing events file
    436 events written to the output file
===============================================================================
   Grand Total      Good   Bad:  Region      Time     Phase       Cut
          2903       436              0      2467         0         0
   in     752.00 seconds
 Command not found; type ? for a command listing
!earthevents:ASCA > set mission ASCA
 
 Notes: XSELECT set up for      ASCA
 Keywords for time and pha are  TIME       PI
 Units of time are              s
 Default timing binsize =    16.00
 Keywords for images are          DETX       DETY
 Keywords for the WMAP are        DETX       DETY
 
!earthevents:ASCA > set datadir .
 
Setting data directory to /data/data22/seq_proc/33012010.005/
Setting mkf directory to /data/data22/seq_proc/33012010.005/
 
!earthevents:ASCA > read events ad33012010g200370m.unf
Got new instrument: GIS2
 
Setting: IMAGE binning    =    1
         WMAP binning     =    1
         Energy Column    =  PI
         Energy rebinning =    1
 
 
Getting Min and Max for Energy Column...
Got min and max for PI:     0   1023
 
Got the minimum time resolution of the read data:  0.50000
 Number of files read in:   1
 
******************** Observation Catalogue ********************
 
Data Directory is: /data/data22/seq_proc/33012010.005/
HK Directory is: /data/data22/seq_proc/33012010.005/
 
!earthevents:ASCA-GIS2-PH > select mkf "FOV==2"  data_dir=. ASCA_mkf_def_expr=ft*.mkf
!earthevents:ASCA-GIS2-PH > extract events
!earthevents:ASCA-GIS2-PH > save events outfile=event.tmp use_events=no
Wrote events list to file event.tmp
!earthevents:ASCA-GIS2-PH > exit save_session=no
-> Extracting bright and dark Earth events from ad33012010g300170h.unf
-> Extracting ad33012010g300170h.drk
-> Standard Output From FTOOL xselect:
 
                         **  XSELECT V1.3   **
 
!> Enter session name >[xsel] earthevents
 
 Notes: XSELECT set up for      ASCA
 Keywords for time and pha are  TIME       PI
 Units of time are              s
 Default timing binsize =    16.00
 Keywords for images are          DETX       DETY
 Keywords for the WMAP are        DETX       DETY
 
 
 
        OBJECT   DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME   NEVENTS  PHA_BINS
      1 XY_ARI   PH       HIGH     29/01/96 17:43:01 0.48E+04     4397     1024
 
EXTRACTOR vers 2.0  11 Apr 1997.
 Skipping file: /data/data22/seq_proc/33012010.005/ad33012010g300170h.unf
 Writing events file
      0 events written to the output file
===============================================================================
   Grand Total      Good   Bad:  Region      Time     Phase       Cut
             0         0              0         0         0         0
   in       0.00 seconds
 Command not found; type ? for a command listing
!earthevents:ASCA > set mission ASCA
 
 Notes: XSELECT set up for      ASCA
 Keywords for time and pha are  TIME       PI
 Units of time are              s
 Default timing binsize =    16.00
 Keywords for images are          DETX       DETY
 Keywords for the WMAP are        DETX       DETY
 
!earthevents:ASCA > set datadir .
 
Setting data directory to /data/data22/seq_proc/33012010.005/
Setting mkf directory to /data/data22/seq_proc/33012010.005/
 
!earthevents:ASCA > read events ad33012010g300170h.unf
Got new instrument: GIS3
 
Setting: IMAGE binning    =    1
         WMAP binning     =    1
         Energy Column    =  PI
         Energy rebinning =    1
 
 
Getting Min and Max for Energy Column...
Got min and max for PI:     0   1023
 
Got the minimum time resolution of the read data:  0.62500E-01
 Number of files read in:   1
 
******************** Observation Catalogue ********************
 
Data Directory is: /data/data22/seq_proc/33012010.005/
HK Directory is: /data/data22/seq_proc/33012010.005/
 
!earthevents:ASCA-GIS3-PH > select mkf "FOV==1"  data_dir=. ASCA_mkf_def_expr=ft*.mkf
!earthevents:ASCA-GIS3-PH > extract events
!earthevents:ASCA-GIS3-PH > save events outfile=event.tmp use_events=no
Wrote events list to file event.tmp
!earthevents:ASCA-GIS3-PH > exit save_session=no
-> Deleting ad33012010g300170h.drk since it contains 0 events
-> Extracting ad33012010g300170h.brt
-> Standard Output From FTOOL xselect:
 
                         **  XSELECT V1.3   **
 
!> Enter session name >[xsel] earthevents
 
 Notes: XSELECT set up for      ASCA
 Keywords for time and pha are  TIME       PI
 Units of time are              s
 Default timing binsize =    16.00
 Keywords for images are          DETX       DETY
 Keywords for the WMAP are        DETX       DETY
 
 
 
        OBJECT   DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME   NEVENTS  PHA_BINS
      1 XY_ARI   PH       HIGH     29/01/96 17:43:01 0.48E+04     4397     1024
 
EXTRACTOR vers 2.0  11 Apr 1997.
 Doing file: /data/data22/seq_proc/33012010.005/ad33012010g300170h.unf
          Total      Good    Bad: Region      Time     Phase       Cut
           4397        52              0      4345         0         0
 Writing events file
     52 events written to the output file
===============================================================================
   Grand Total      Good   Bad:  Region      Time     Phase       Cut
          4397        52              0      4345         0         0
   in      92.00 seconds
 Command not found; type ? for a command listing
!earthevents:ASCA > set mission ASCA
 
 Notes: XSELECT set up for      ASCA
 Keywords for time and pha are  TIME       PI
 Units of time are              s
 Default timing binsize =    16.00
 Keywords for images are          DETX       DETY
 Keywords for the WMAP are        DETX       DETY
 
!earthevents:ASCA > set datadir .
 
Setting data directory to /data/data22/seq_proc/33012010.005/
Setting mkf directory to /data/data22/seq_proc/33012010.005/
 
!earthevents:ASCA > read events ad33012010g300170h.unf
Got new instrument: GIS3
 
Setting: IMAGE binning    =    1
         WMAP binning     =    1
         Energy Column    =  PI
         Energy rebinning =    1
 
 
Getting Min and Max for Energy Column...
Got min and max for PI:     0   1023
 
Got the minimum time resolution of the read data:  0.62500E-01
 Number of files read in:   1
 
******************** Observation Catalogue ********************
 
Data Directory is: /data/data22/seq_proc/33012010.005/
HK Directory is: /data/data22/seq_proc/33012010.005/
 
!earthevents:ASCA-GIS3-PH > select mkf "FOV==2"  data_dir=. ASCA_mkf_def_expr=ft*.mkf
!earthevents:ASCA-GIS3-PH > extract events
!earthevents:ASCA-GIS3-PH > save events outfile=event.tmp use_events=no
Wrote events list to file event.tmp
!earthevents:ASCA-GIS3-PH > exit save_session=no
-> Extracting bright and dark Earth events from ad33012010g300270l.unf
-> Extracting ad33012010g300270l.drk
-> Standard Output From FTOOL xselect:
 
                         **  XSELECT V1.3   **
 
!> Enter session name >[xsel] earthevents
 
 Notes: XSELECT set up for      ASCA
 Keywords for time and pha are  TIME       PI
 Units of time are              s
 Default timing binsize =    16.00
 Keywords for images are          DETX       DETY
 Keywords for the WMAP are        DETX       DETY
 
 
 
        OBJECT   DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME   NEVENTS  PHA_BINS
      1 XY_ARI   PH       LOW      29/01/96 18:46:29 0.60E+04     3589     1024
 
EXTRACTOR vers 2.0  11 Apr 1997.
 Doing file: /data/data22/seq_proc/33012010.005/ad33012010g300270l.unf
          Total      Good    Bad: Region      Time     Phase       Cut
           3589      1834              0      1755         0         0
 Writing events file
   1834 events written to the output file
===============================================================================
   Grand Total      Good   Bad:  Region      Time     Phase       Cut
          3589      1834              0      1755         0         0
   in    2688.09 seconds
 Command not found; type ? for a command listing
!earthevents:ASCA > set mission ASCA
 
 Notes: XSELECT set up for      ASCA
 Keywords for time and pha are  TIME       PI
 Units of time are              s
 Default timing binsize =    16.00
 Keywords for images are          DETX       DETY
 Keywords for the WMAP are        DETX       DETY
 
!earthevents:ASCA > set datadir .
 
Setting data directory to /data/data22/seq_proc/33012010.005/
Setting mkf directory to /data/data22/seq_proc/33012010.005/
 
!earthevents:ASCA > read events ad33012010g300270l.unf
Got new instrument: GIS3
 
Setting: IMAGE binning    =    1
         WMAP binning     =    1
         Energy Column    =  PI
         Energy rebinning =    1
 
 
Getting Min and Max for Energy Column...
Got min and max for PI:     0   1023
 
Got the minimum time resolution of the read data:   2.0000
 Number of files read in:   1
 
******************** Observation Catalogue ********************
 
Data Directory is: /data/data22/seq_proc/33012010.005/
HK Directory is: /data/data22/seq_proc/33012010.005/
 
!earthevents:ASCA-GIS3-PH > select mkf "FOV==1"  data_dir=. ASCA_mkf_def_expr=ft*.mkf
!earthevents:ASCA-GIS3-PH > extract events
!earthevents:ASCA-GIS3-PH > save events outfile=event.tmp use_events=no
Wrote events list to file event.tmp
!earthevents:ASCA-GIS3-PH > exit save_session=no
-> Extracting ad33012010g300270l.brt
-> Standard Output From FTOOL xselect:
 
                         **  XSELECT V1.3   **
 
!> Enter session name >[xsel] earthevents
 
 Notes: XSELECT set up for      ASCA
 Keywords for time and pha are  TIME       PI
 Units of time are              s
 Default timing binsize =    16.00
 Keywords for images are          DETX       DETY
 Keywords for the WMAP are        DETX       DETY
 
 
 
        OBJECT   DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME   NEVENTS  PHA_BINS
      1 XY_ARI   PH       LOW      29/01/96 18:46:29 0.60E+04     3589     1024
 
EXTRACTOR vers 2.0  11 Apr 1997.
 Doing file: /data/data22/seq_proc/33012010.005/ad33012010g300270l.unf
          Total      Good    Bad: Region      Time     Phase       Cut
           3589      1527              0      2062         0         0
 Writing events file
   1527 events written to the output file
===============================================================================
   Grand Total      Good   Bad:  Region      Time     Phase       Cut
          3589      1527              0      2062         0         0
   in    3072.00 seconds
 Command not found; type ? for a command listing
!earthevents:ASCA > set mission ASCA
 
 Notes: XSELECT set up for      ASCA
 Keywords for time and pha are  TIME       PI
 Units of time are              s
 Default timing binsize =    16.00
 Keywords for images are          DETX       DETY
 Keywords for the WMAP are        DETX       DETY
 
!earthevents:ASCA > set datadir .
 
Setting data directory to /data/data22/seq_proc/33012010.005/
Setting mkf directory to /data/data22/seq_proc/33012010.005/
 
!earthevents:ASCA > read events ad33012010g300270l.unf
Got new instrument: GIS3
 
Setting: IMAGE binning    =    1
         WMAP binning     =    1
         Energy Column    =  PI
         Energy rebinning =    1
 
 
Getting Min and Max for Energy Column...
Got min and max for PI:     0   1023
 
Got the minimum time resolution of the read data:   2.0000
 Number of files read in:   1
 
******************** Observation Catalogue ********************
 
Data Directory is: /data/data22/seq_proc/33012010.005/
HK Directory is: /data/data22/seq_proc/33012010.005/
 
!earthevents:ASCA-GIS3-PH > select mkf "FOV==2"  data_dir=. ASCA_mkf_def_expr=ft*.mkf
!earthevents:ASCA-GIS3-PH > extract events
!earthevents:ASCA-GIS3-PH > save events outfile=event.tmp use_events=no
Wrote events list to file event.tmp
!earthevents:ASCA-GIS3-PH > exit save_session=no
-> Extracting bright and dark Earth events from ad33012010g300370m.unf
-> Extracting ad33012010g300370m.drk
-> Standard Output From FTOOL xselect:
 
                         **  XSELECT V1.3   **
 
!> Enter session name >[xsel] earthevents
 
 Notes: XSELECT set up for      ASCA
 Keywords for time and pha are  TIME       PI
 Units of time are              s
 Default timing binsize =    16.00
 Keywords for images are          DETX       DETY
 Keywords for the WMAP are        DETX       DETY
 
 
 
        OBJECT   DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME   NEVENTS  PHA_BINS
      1 XY_ARI   PH       MEDIUM   29/01/96 17:30:29 0.33E+04     2867     1024
 
EXTRACTOR vers 2.0  11 Apr 1997.
 Skipping file: /data/data22/seq_proc/33012010.005/ad33012010g300370m.unf
 Writing events file
      0 events written to the output file
===============================================================================
   Grand Total      Good   Bad:  Region      Time     Phase       Cut
             0         0              0         0         0         0
   in       0.00 seconds
 Command not found; type ? for a command listing
!earthevents:ASCA > set mission ASCA
 
 Notes: XSELECT set up for      ASCA
 Keywords for time and pha are  TIME       PI
 Units of time are              s
 Default timing binsize =    16.00
 Keywords for images are          DETX       DETY
 Keywords for the WMAP are        DETX       DETY
 
!earthevents:ASCA > set datadir .
 
Setting data directory to /data/data22/seq_proc/33012010.005/
Setting mkf directory to /data/data22/seq_proc/33012010.005/
 
!earthevents:ASCA > read events ad33012010g300370m.unf
Got new instrument: GIS3
 
Setting: IMAGE binning    =    1
         WMAP binning     =    1
         Energy Column    =  PI
         Energy rebinning =    1
 
 
Getting Min and Max for Energy Column...
Got min and max for PI:     0   1023
 
Got the minimum time resolution of the read data:  0.50000
 Number of files read in:   1
 
******************** Observation Catalogue ********************
 
Data Directory is: /data/data22/seq_proc/33012010.005/
HK Directory is: /data/data22/seq_proc/33012010.005/
 
!earthevents:ASCA-GIS3-PH > select mkf "FOV==1"  data_dir=. ASCA_mkf_def_expr=ft*.mkf
!earthevents:ASCA-GIS3-PH > extract events
!earthevents:ASCA-GIS3-PH > save events outfile=event.tmp use_events=no
Wrote events list to file event.tmp
!earthevents:ASCA-GIS3-PH > exit save_session=no
-> Deleting ad33012010g300370m.drk since it contains 0 events
-> Extracting ad33012010g300370m.brt
-> Standard Output From FTOOL xselect:
 
                         **  XSELECT V1.3   **
 
!> Enter session name >[xsel] earthevents
 
 Notes: XSELECT set up for      ASCA
 Keywords for time and pha are  TIME       PI
 Units of time are              s
 Default timing binsize =    16.00
 Keywords for images are          DETX       DETY
 Keywords for the WMAP are        DETX       DETY
 
 
 
        OBJECT   DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME   NEVENTS  PHA_BINS
      1 XY_ARI   PH       MEDIUM   29/01/96 17:30:29 0.33E+04     2867     1024
 
EXTRACTOR vers 2.0  11 Apr 1997.
 Doing file: /data/data22/seq_proc/33012010.005/ad33012010g300370m.unf
          Total      Good    Bad: Region      Time     Phase       Cut
           2867       439              0      2428         0         0
 Writing events file
    439 events written to the output file
===============================================================================
   Grand Total      Good   Bad:  Region      Time     Phase       Cut
          2867       439              0      2428         0         0
   in     752.00 seconds
 Command not found; type ? for a command listing
!earthevents:ASCA > set mission ASCA
 
 Notes: XSELECT set up for      ASCA
 Keywords for time and pha are  TIME       PI
 Units of time are              s
 Default timing binsize =    16.00
 Keywords for images are          DETX       DETY
 Keywords for the WMAP are        DETX       DETY
 
!earthevents:ASCA > set datadir .
 
Setting data directory to /data/data22/seq_proc/33012010.005/
Setting mkf directory to /data/data22/seq_proc/33012010.005/
 
!earthevents:ASCA > read events ad33012010g300370m.unf
Got new instrument: GIS3
 
Setting: IMAGE binning    =    1
         WMAP binning     =    1
         Energy Column    =  PI
         Energy rebinning =    1
 
 
Getting Min and Max for Energy Column...
Got min and max for PI:     0   1023
 
Got the minimum time resolution of the read data:  0.50000
 Number of files read in:   1
 
******************** Observation Catalogue ********************
 
Data Directory is: /data/data22/seq_proc/33012010.005/
HK Directory is: /data/data22/seq_proc/33012010.005/
 
!earthevents:ASCA-GIS3-PH > select mkf "FOV==2"  data_dir=. ASCA_mkf_def_expr=ft*.mkf
!earthevents:ASCA-GIS3-PH > extract events
!earthevents:ASCA-GIS3-PH > save events outfile=event.tmp use_events=no
Wrote events list to file event.tmp
!earthevents:ASCA-GIS3-PH > exit save_session=no

Determining information about this observation ( 15:48:36 )

-> Calculating ISAS time for sis
-> Calculating ISAS time for gis
-> Recording dates of PI calibration files
-> Standard Output From FTOOL sec2time:
 Offset of  1.500000000000000E+08 from 1/1/93     0:0:0
 is date and time (including leapseconds) = 3/10/97    2:39:56.000000
 Modified Julian Day    =   50724.111064814816928

Generating event file information page ( 15:49:58 )

-> Summing time and events for s0 event files
-> listing ad33012010s000102h.unf
-> listing ad33012010s000302m.unf
-> listing ad33012010s000202l.unf
-> listing ad33012010s000112h.unf
-> listing ad33012010s000312m.unf
-> listing ad33012010s000212l.unf
-> listing ad33012010s000101h.unf
-> listing ad33012010s000301m.unf
-> listing ad33012010s000201l.unf
-> Summing time and events for s1 event files
-> listing ad33012010s100102h.unf
-> listing ad33012010s100302m.unf
-> listing ad33012010s100202l.unf
-> listing ad33012010s100112h.unf
-> listing ad33012010s100312m.unf
-> listing ad33012010s100212l.unf
-> listing ad33012010s100101h.unf
-> listing ad33012010s100301m.unf
-> listing ad33012010s100201l.unf
-> Summing time and events for g2 event files
-> listing ad33012010g200170h.unf
-> listing ad33012010g200370m.unf
-> listing ad33012010g200270l.unf
-> Summing time and events for g3 event files
-> listing ad33012010g300170h.unf
-> listing ad33012010g300370m.unf
-> listing ad33012010g300270l.unf

Creating sequence documentation ( 15:56:58 )


Creating HTML source list ( 15:57:31 )


Listing the files for distribution ( 15:58:43 )

-> Saving job.par as ad33012010_005_job.par and process.par as ad33012010_005_process.par
-> Creating the FITS format file catalog ad33012010_tape.cat
-> Creating the trend product catalog
-> Creating the FITS format file catalog ad33012010_trend.cat
-> Creating ad33012010_005_file_info.html

Doing final wrap up of all files ( 16:05:35 )

-> Adding FITS keywords to all distributed FITS files
-> Running fverify on all distributed files
-> Calculating checksums for all FITS files
-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.
-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.
-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.
-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.
-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.
-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.
-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.
-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.
-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.
-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.
-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.
-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.
-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.
-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.
-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.
-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.
-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.
-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.
-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.
-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.
-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.
-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.
-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.
-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.
-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.
-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.
-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.
-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.
-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.
-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.
-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.
-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.
-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.
-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.
-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.
-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.
-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.
-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.
-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.
-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.
-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.
-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.
-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.
-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.
-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.
-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.
-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.
-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.
-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.
-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.
-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.
-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.
-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.
-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.
-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.
-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.
-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.
-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.
-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.
-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.
-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.
-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.
-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.
-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.
-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.
-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.
-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.
-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.
-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.
-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.
-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.
-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.
-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.
-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.
-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.
-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.
-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.
-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.
-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.
-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.
-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.
-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.
-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.
-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.
-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.
-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.
-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.
-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.
-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.
-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.
-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.
-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.
-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.
-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.
-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.
-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.
-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.
-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.
-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.
-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.
-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.
-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.
-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.
-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.
-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.
-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.
-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.
-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.
-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.
-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.
-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.
-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.
-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.
-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.
-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.
-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.
-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.
-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.
-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.
-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.
-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.
-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.
-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.
-> Doing inventory of all files

Processing complete ( 16:30:20 )