The following information is also available:
Time column is TIME ORDERED-> Fetching fa930427_2350.1950.Z
Time column is TIME ORDERED-> Fetching fa930428_1949.2350.Z
fa930427_2350.1950 fa930428_1949.2350-> Checking if column TIME in merged.tmp is in order
Time column is TIME ORDERED-> Running attitude FTOOL on merged attitude file
ATTITUDE_V0.9j
reading attitude file:./merged.tmp
open asc output file:out.tmp
AVERAGE ASPECT AND OFFSET FOR THIS ATTITUDE FILE:
Attitude file start and stop ascatime : 10108240.723100 10194636.456400
Data file start and stop ascatime : 10108240.723100 10194636.456400
Aspecting run start and stop ascatime : 10108240.723170 10194636.456285
Time interval averaged over (seconds) : 86395.733115
Total pointing and manuver time (sec) : 86395.984375 0.000000
Mean boresight Euler angles : 288.234830 85.220059 16.097917
RA DEC SUN ANGLE
Mean solar position (deg) : 34.88 13.92
Mean aberration (arcsec) : 7.12 -7.98
Mean sat X-axis (deg) : 2.129317 -73.225434 89.70
Mean sat Y-axis (deg) : 19.612436 16.040418 14.90
Mean sat Z-axis (deg) : 288.234830 4.779941 104.89
RA DEC ROLL OFFSET
(deg) (deg) (deg) (arcmin)
Average 288.440552 4.976892 286.080414 0.166864
Minimum 288.260345 4.972697 286.069733 0.000000
Maximum 288.558258 5.573216 286.168304 36.463665
Sigma (RMS) 0.000257 0.000540 0.003630 0.465403
Number of ASPECT records processed = 67305
Aspecting to RA/DEC : 288.44055176 4.97689199
closing output file...
closing attitude file...
-> Standard Output From STOOL checkatt:
Opening file: ./out.tmp
***************** Observation Info ******************
RA (J2000 deg): 288.441 DEC: 4.977
START TIME: SC 10108240.7232 = UT 27/04/93 23:50:40
****** Definition of Attitude SENSOR Bit Flags ******
Sensors used in the attitude determination and attitude control mode
1: USED, 0: NOT USED
B0:STT-A, B1:STT-B, B2:NSAS, B3:GAS, B4:SSAS-SA, B5:SSAS-SB,
B6:IRU-X, B7:IRU-Y, B8:IRU-Z, B9:IRU-S1, B10:IRU-S2,
B11: Attitude control mode 1: coarse, 0: fine
B12: Sun presence 1: day, 0: night
B13: STT-A earth occultation 1: earth occultation, 0: no occultation
B14: STT-B earth occultation 1: earth occultation, 0: no occultation
B16,17,18: STT-A track stars no.1,2,3, 1: USED, 0: NOT USED
B19,20,21: STT-B track stars no.1,2,3, 1: USED, 0: NOT USED
B22,23: always 0
******** Attitude File Reconstruction Summary *******
S S N G S S I I I I I A S S S S S
T T S A S S R R R R R C U T T T T
T T A S A A U U U U U M N T T T T
- - S . A A - - - - - . . - - - -
A B . . - - X Y Z S S . . A B A B
. . . . S S . . . 1 2 . . O O S S
offset_time separation sensor . . . . A B . . . . . . . C C T T
(sec) (arcmin) . . . . . . . . . . . . . C C R R
BIT: 0 1 2 3 4 5 6 7 8 9 A B C D E
4.000089 11.683 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
151.999603 10.679 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
383.998779 9.598 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
415.998688 8.535 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
443.998627 7.482 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
471.998474 6.452 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
503.998383 5.367 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
539.998291 4.312 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
583.998108 3.275 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
643.997925 2.242 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
739.997620 1.235 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
1003.996704 0.231 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
86395.734375 36.464 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
Attitude Records: 67305
Attitude Steps: 13
Maneuver ACM time: 0. sec
Pointed ACM time: 86396.2 sec
-> Calculating aspect point100 100 count=20 sum1=5761.22 sum2=1702.95 sum3=322.895 101 100 count=54 sum1=15555.9 sum2=4598.24 sum3=872.326 101 101 count=1 sum1=288.075 sum2=85.155 sum3=16.156 102 100 count=3 sum1=864.228 sum2=255.462 sum3=48.476 102 101 count=16 sum1=4609.24 sum2=1362.49 sum3=258.52 103 101 count=5 sum1=1440.45 sum2=425.806 sum3=80.757 104 101 count=1 sum1=288.096 sum2=85.164 sum3=16.15 104 102 count=4 sum1=1152.4 sum2=340.668 sum3=64.596 105 102 count=4 sum1=1152.44 sum2=340.683 sum3=64.576 106 103 count=5 sum1=1440.6 sum2=425.879 sum3=80.691 107 103 count=4 sum1=1152.52 sum2=340.722 sum3=64.537 108 103 count=3 sum1=864.414 sum2=255.55 sum3=48.392 108 104 count=2 sum1=576.286 sum2=170.371 sum3=32.259 109 104 count=5 sum1=1440.76 sum2=425.944 sum3=80.631 110 104 count=5 sum1=1440.8 sum2=425.963 sum3=80.612 111 105 count=6 sum1=1729.02 sum2=511.179 sum3=96.711 112 105 count=8 sum1=2305.44 sum2=681.604 sum3=128.917 113 105 count=4 sum1=1152.75 sum2=340.814 sum3=64.448 113 106 count=5 sum1=1440.96 sum2=426.028 sum3=80.549 114 106 count=12 sum1=3458.4 sum2=1022.5 sum3=193.282 115 106 count=17 sum1=4899.58 sum2=1448.61 sum3=273.753 116 106 count=6 sum1=1729.3 sum2=511.284 sum3=96.604 116 107 count=19 sum1=5476.21 sum2=1619.1 sum3=305.88 117 107 count=23605 sum1=6.80374e+06 sum2=2.01162e+06 sum3=379994 118 106 count=56 sum1=16141.3 sum2=4771.98 sum3=901.785 118 107 count=43307 sum1=1.24826e+07 sum2=3.69064e+06 sum3=697143 119 107 count=126 sum1=36319.1 sum2=10738.1 sum3=2027.65 129 47 count=1 sum1=288.353 sum2=84.624 sum3=16.188 0 out of 67304 points outside bin structure-> Euler angles: 288.235, 85.2202, 16.0978
Interpolating 59 records in time interval 1.01946e+07 - 1.01946e+07
frf_directory,s,h,"./",,,"frf directory" frf_file,s,h,"ft930427_2350.1950",,,"frf telemetry file" frf_file,s,h,"ft930428_1949.2350",,,"frf telemetry file"-> Standard Output From FTOOL frfread:
Frfread version 3.00 patch 32 ASCA format Telemetry file: ft930427_2350.1950 Initial mode = 2 (Bright) Initial value for dummy = 0 Initial datamode = 0 (Observation) Initial sis = 0 Initial bit_rate = 2 Reading all superframes reading PH mode reading PCAL mode reading MPCmode Warning: ccdlist pattern 0 2 2 3 for S0 indicates 3-CCD mode in superframe 9607 Warning: ccdlist pattern 0 2 2 3 for S0 indicates 3-CCD mode in superframe 9607 Warning: ccdlist pattern 0 2 2 3 for S0 indicates 3-CCD mode in superframe 9607 No mode = 0 Faint = 802976 Bright = 174624 Fast = 0 Frame = 0 Dark frame = 0 Histogram = 0 Integration = 0 PH = 977600 MPC = 0 PCAL = 0 Memory Check = 0 Number of superframes = 15308 no. of SIS events found = 981793 ASCA format Telemetry file: ft930428_1949.2350 Initial mode = 2 (Bright) Initial value for dummy = 0 Initial datamode = 0 (Observation) Initial sis = 0 Initial bit_rate = 2 Reading all superframes reading PH mode reading PCAL mode reading MPCmode No mode = 0 Faint = 49056 Bright = 51488 Fast = 0 Frame = 0 Dark frame = 0 Histogram = 0 Integration = 0 PH = 100544 MPC = 0 PCAL = 0 Memory Check = 0 Number of superframes = 1573 no. of SIS events found = 166101-> Standard Error Output From FTOOL frfread
coordinate error 432 178 coordinate error 0 0 coordinate error 256 0 coordinate error 96 0 coordinate error 48 0 coordinate error 5 114 coordinate error 64 496 coordinate error 58 488 coordinate error 36 459 coordinate error 0 0 coordinate error 0 0 coordinate error 0 0 coordinate error 0 0 coordinate error 0 0 coordinate error 0 0 coordinate error 0 0 coordinate error 0 0 coordinate error 0 0 coordinate error 0 1 coordinate error 0 2 coordinate error 0 4 coordinate error 0 8 coordinate error 0 16 coordinate error 0 32 coordinate error 0 70 coordinate error 0 128 coordinate error 0 256 coordinate error 1 391 coordinate error 2 0 coordinate error 4 0 coordinate error 8 0 coordinate error 16 0 coordinate error 32 0 coordinate error 96 0 coordinate error 0 24 coordinate error 0 0 coordinate error 505 133-> Removing the following files with NEVENTS=0
ft930427_2350_1950G200399.fits ft930427_2350_1950G201570M.fits ft930427_2350_1950G202370M.fits ft930427_2350_1950G202699.fits ft930427_2350_1950G203470M.fits ft930427_2350_1950G204570M.fits ft930427_2350_1950G205299.fits ft930427_2350_1950G205570H.fits ft930427_2350_1950G205670M.fits ft930427_2350_1950G205770M.fits ft930427_2350_1950G205870H.fits ft930427_2350_1950G205970H.fits ft930427_2350_1950G206070H.fits ft930427_2350_1950G206170H.fits ft930427_2350_1950G206699.fits ft930427_2350_1950G206970H.fits ft930427_2350_1950G207070M.fits ft930427_2350_1950G207170M.fits ft930427_2350_1950G207270H.fits ft930427_2350_1950G207370H.fits ft930427_2350_1950G207470H.fits ft930427_2350_1950G207570H.fits ft930427_2350_1950G207670H.fits ft930427_2350_1950G208170H.fits ft930427_2350_1950G208270M.fits ft930427_2350_1950G208370M.fits ft930427_2350_1950G208470H.fits ft930427_2350_1950G208570H.fits ft930427_2350_1950G208670H.fits ft930427_2350_1950G208770H.fits ft930427_2350_1950G209470H.fits ft930427_2350_1950G209570H.fits ft930427_2350_1950G209670M.fits ft930427_2350_1950G209770M.fits ft930427_2350_1950G300399.fits ft930427_2350_1950G300670H.fits ft930427_2350_1950G301570M.fits ft930427_2350_1950G302370M.fits ft930427_2350_1950G302699.fits ft930427_2350_1950G303470M.fits ft930427_2350_1950G304570M.fits ft930427_2350_1950G305299.fits ft930427_2350_1950G305570H.fits ft930427_2350_1950G305670M.fits ft930427_2350_1950G305770M.fits ft930427_2350_1950G305870H.fits ft930427_2350_1950G305970H.fits ft930427_2350_1950G306070H.fits ft930427_2350_1950G306170H.fits ft930427_2350_1950G306699.fits ft930427_2350_1950G307970H.fits ft930427_2350_1950G308070M.fits ft930427_2350_1950G308170M.fits ft930427_2350_1950G308270H.fits ft930427_2350_1950G308370H.fits ft930427_2350_1950G308470H.fits ft930427_2350_1950G308570H.fits ft930427_2350_1950G309170H.fits ft930427_2350_1950G309270M.fits ft930427_2350_1950G309370M.fits ft930427_2350_1950G309470H.fits ft930427_2350_1950G309570H.fits ft930427_2350_1950G309670H.fits ft930427_2350_1950G309770H.fits ft930427_2350_1950G310270H.fits ft930427_2350_1950G310370H.fits ft930427_2350_1950G310470M.fits ft930427_2350_1950G310570M.fits ft930427_2350_1950S000399.fits ft930427_2350_1950S000602H.fits ft930427_2350_1950S001002H.fits ft930427_2350_1950S001202M.fits ft930427_2350_1950S001602H.fits ft930427_2350_1950S002099.fits ft930427_2350_1950S002302H.fits ft930427_2350_1950S002502M.fits ft930427_2350_1950S002902H.fits ft930427_2350_1950S003102M.fits ft930427_2350_1950S003202M.fits ft930427_2350_1950S003599.fits ft930427_2350_1950S003702H.fits ft930427_2350_1950S004399.fits ft930427_2350_1950S005002H.fits ft930427_2350_1950S005202M.fits ft930427_2350_1950S005602H.fits ft930427_2350_1950S005802M.fits ft930427_2350_1950S006302H.fits ft930427_2350_1950S006402M.fits ft930427_2350_1950S006802H.fits ft930427_2350_1950S100399.fits ft930427_2350_1950S100602H.fits ft930427_2350_1950S101002H.fits ft930427_2350_1950S101202M.fits ft930427_2350_1950S101602H.fits ft930427_2350_1950S102099.fits ft930427_2350_1950S102302H.fits ft930427_2350_1950S102502M.fits ft930427_2350_1950S102902H.fits ft930427_2350_1950S103102M.fits ft930427_2350_1950S103202M.fits ft930427_2350_1950S103599.fits ft930427_2350_1950S104299.fits ft930427_2350_1950S104802H.fits ft930427_2350_1950S105002M.fits ft930427_2350_1950S105402H.fits ft930427_2350_1950S105602M.fits ft930427_2350_1950S106102H.fits ft930427_2350_1950S106202M.fits ft930427_2350_1950S106602H.fits ft930428_1949_2350G200370M.fits ft930428_1949_2350G200770M.fits ft930428_1949_2350G200899.fits ft930428_1949_2350G300370M.fits ft930428_1949_2350G300770M.fits ft930428_1949_2350G300899.fits ft930428_1949_2350S000202M.fits ft930428_1949_2350S000499.fits ft930428_1949_2350S000802H.fits ft930428_1949_2350S100202M.fits ft930428_1949_2350S100499.fits ft930428_1949_2350S100802H.fits-> Checking for empty GTI extensions
ft930427_2350_1950S000102M.fits[3] ft930427_2350_1950S000202L.fits[3] ft930427_2350_1950S000402M.fits[3] ft930427_2350_1950S000501H.fits[3] ft930427_2350_1950S000702M.fits[3] ft930427_2350_1950S000801M.fits[3] ft930427_2350_1950S000901H.fits[3] ft930427_2350_1950S001102M.fits[3] ft930427_2350_1950S001302M.fits[3] ft930427_2350_1950S001401M.fits[3] ft930427_2350_1950S001501H.fits[3] ft930427_2350_1950S001702M.fits[3] ft930427_2350_1950S001802M.fits[3] ft930427_2350_1950S001902M.fits[3] ft930427_2350_1950S002102M.fits[3] ft930427_2350_1950S002201H.fits[3] ft930427_2350_1950S002402M.fits[3] ft930427_2350_1950S002602M.fits[3] ft930427_2350_1950S002701M.fits[3] ft930427_2350_1950S002801H.fits[3] ft930427_2350_1950S003002M.fits[3] ft930427_2350_1950S003301M.fits[3] ft930427_2350_1950S003401H.fits[3] ft930427_2350_1950S003601H.fits[3] ft930427_2350_1950S003802M.fits[3] ft930427_2350_1950S003902M.fits[3] ft930427_2350_1950S004002M.fits[3] ft930427_2350_1950S004102H.fits[3] ft930427_2350_1950S004201H.fits[3] ft930427_2350_1950S004401H.fits[3] ft930427_2350_1950S004501H.fits[3] ft930427_2350_1950S004601H.fits[3] ft930427_2350_1950S004701H.fits[3] ft930427_2350_1950S004801H.fits[3] ft930427_2350_1950S004901H.fits[3] ft930427_2350_1950S005102M.fits[3] ft930427_2350_1950S005302M.fits[3] ft930427_2350_1950S005402H.fits[3] ft930427_2350_1950S005501H.fits[3] ft930427_2350_1950S005702M.fits[3] ft930427_2350_1950S005902M.fits[3] ft930427_2350_1950S006002H.fits[3] ft930427_2350_1950S006101H.fits[3] ft930427_2350_1950S006201H.fits[3] ft930427_2350_1950S006502M.fits[3] ft930427_2350_1950S006601M.fits[3] ft930427_2350_1950S006701H.fits[3] ft930428_1949_2350S000102M.fits[3] ft930428_1949_2350S000302M.fits[3] ft930428_1949_2350S000502M.fits[3] ft930428_1949_2350S000601M.fits[3] ft930428_1949_2350S000701H.fits[3] ft930428_1949_2350S000902M.fits[3]-> Merging GTIs from the following files:
ft930427_2350_1950S100102M.fits[3] ft930427_2350_1950S100202L.fits[3] ft930427_2350_1950S100402M.fits[3] ft930427_2350_1950S100501H.fits[3] ft930427_2350_1950S100702M.fits[3] ft930427_2350_1950S100801M.fits[3] ft930427_2350_1950S100901H.fits[3] ft930427_2350_1950S101102M.fits[3] ft930427_2350_1950S101302M.fits[3] ft930427_2350_1950S101401M.fits[3] ft930427_2350_1950S101501H.fits[3] ft930427_2350_1950S101702M.fits[3] ft930427_2350_1950S101802M.fits[3] ft930427_2350_1950S101902M.fits[3] ft930427_2350_1950S102102M.fits[3] ft930427_2350_1950S102201H.fits[3] ft930427_2350_1950S102402M.fits[3] ft930427_2350_1950S102602M.fits[3] ft930427_2350_1950S102701M.fits[3] ft930427_2350_1950S102801H.fits[3] ft930427_2350_1950S103002M.fits[3] ft930427_2350_1950S103301M.fits[3] ft930427_2350_1950S103401H.fits[3] ft930427_2350_1950S103601H.fits[3] ft930427_2350_1950S103702M.fits[3] ft930427_2350_1950S103802M.fits[3] ft930427_2350_1950S103902M.fits[3] ft930427_2350_1950S104002H.fits[3] ft930427_2350_1950S104101H.fits[3] ft930427_2350_1950S104301H.fits[3] ft930427_2350_1950S104401H.fits[3] ft930427_2350_1950S104501H.fits[3] ft930427_2350_1950S104601H.fits[3] ft930427_2350_1950S104701H.fits[3] ft930427_2350_1950S104902M.fits[3] ft930427_2350_1950S105102M.fits[3] ft930427_2350_1950S105202H.fits[3] ft930427_2350_1950S105301H.fits[3] ft930427_2350_1950S105502M.fits[3] ft930427_2350_1950S105702M.fits[3] ft930427_2350_1950S105802H.fits[3] ft930427_2350_1950S105901H.fits[3] ft930427_2350_1950S106001H.fits[3] ft930427_2350_1950S106302M.fits[3] ft930427_2350_1950S106401M.fits[3] ft930427_2350_1950S106501H.fits[3] ft930428_1949_2350S100102M.fits[3] ft930428_1949_2350S100302M.fits[3] ft930428_1949_2350S100502M.fits[3] ft930428_1949_2350S100601M.fits[3] ft930428_1949_2350S100701H.fits[3] ft930428_1949_2350S100902M.fits[3]-> Merging GTIs from the following files:
ft930427_2350_1950G200170M.fits[3] ft930427_2350_1950G200270L.fits[3] ft930427_2350_1950G200470M.fits[3] ft930427_2350_1950G200570H.fits[3] ft930427_2350_1950G200670H.fits[3] ft930427_2350_1950G200770H.fits[3] ft930427_2350_1950G200870H.fits[3] ft930427_2350_1950G200970M.fits[3] ft930427_2350_1950G201070M.fits[3] ft930427_2350_1950G201170H.fits[3] ft930427_2350_1950G201270H.fits[3] ft930427_2350_1950G201370H.fits[3] ft930427_2350_1950G201470H.fits[3] ft930427_2350_1950G201670M.fits[3] ft930427_2350_1950G201770H.fits[3] ft930427_2350_1950G201870H.fits[3] ft930427_2350_1950G201970H.fits[3] ft930427_2350_1950G202070H.fits[3] ft930427_2350_1950G202170M.fits[3] ft930427_2350_1950G202270M.fits[3] ft930427_2350_1950G202470M.fits[3] ft930427_2350_1950G202570M.fits[3] ft930427_2350_1950G202770M.fits[3] ft930427_2350_1950G202870H.fits[3] ft930427_2350_1950G202970H.fits[3] ft930427_2350_1950G203070H.fits[3] ft930427_2350_1950G203170H.fits[3] ft930427_2350_1950G203270M.fits[3] ft930427_2350_1950G203370M.fits[3] ft930427_2350_1950G203570M.fits[3] ft930427_2350_1950G203670M.fits[3] ft930427_2350_1950G203770H.fits[3] ft930427_2350_1950G203870H.fits[3] ft930427_2350_1950G203970H.fits[3] ft930427_2350_1950G204070H.fits[3] ft930427_2350_1950G204170H.fits[3] ft930427_2350_1950G204270H.fits[3] ft930427_2350_1950G204370M.fits[3] ft930427_2350_1950G204470M.fits[3] ft930427_2350_1950G204670M.fits[3] ft930427_2350_1950G204770M.fits[3] ft930427_2350_1950G204870H.fits[3] ft930427_2350_1950G204970H.fits[3] ft930427_2350_1950G205070H.fits[3] ft930427_2350_1950G205170H.fits[3] ft930427_2350_1950G205370H.fits[3] ft930427_2350_1950G205470H.fits[3] ft930427_2350_1950G206270H.fits[3] ft930427_2350_1950G206370H.fits[3] ft930427_2350_1950G206470H.fits[3] ft930427_2350_1950G206570H.fits[3] ft930427_2350_1950G206770H.fits[3] ft930427_2350_1950G206870H.fits[3] ft930427_2350_1950G207770H.fits[3] ft930427_2350_1950G207870H.fits[3] ft930427_2350_1950G207970H.fits[3] ft930427_2350_1950G208070H.fits[3] ft930427_2350_1950G208870H.fits[3] ft930427_2350_1950G208970H.fits[3] ft930427_2350_1950G209070H.fits[3] ft930427_2350_1950G209170H.fits[3] ft930427_2350_1950G209270H.fits[3] ft930427_2350_1950G209370H.fits[3] ft930427_2350_1950G209870M.fits[3] ft930427_2350_1950G209970M.fits[3] ft930427_2350_1950G210070H.fits[3] ft930427_2350_1950G210170H.fits[3] ft930427_2350_1950G210270H.fits[3] ft930427_2350_1950G210370H.fits[3] ft930428_1949_2350G200170M.fits[3] ft930428_1949_2350G200270M.fits[3] ft930428_1949_2350G200470M.fits[3] ft930428_1949_2350G200570M.fits[3] ft930428_1949_2350G200670M.fits[3] ft930428_1949_2350G200970M.fits[3] ft930428_1949_2350G201070H.fits[3] ft930428_1949_2350G201170H.fits[3] ft930428_1949_2350G201270H.fits[3] ft930428_1949_2350G201370H.fits[3] ft930428_1949_2350G201470M.fits[3] ft930428_1949_2350G201570M.fits[3]-> Merging GTIs from the following files:
ft930427_2350_1950G300170M.fits[3] ft930427_2350_1950G300270L.fits[3] ft930427_2350_1950G300470M.fits[3] ft930427_2350_1950G300570H.fits[3] ft930427_2350_1950G300770H.fits[3] ft930427_2350_1950G300870H.fits[3] ft930427_2350_1950G300970M.fits[3] ft930427_2350_1950G301070M.fits[3] ft930427_2350_1950G301170H.fits[3] ft930427_2350_1950G301270H.fits[3] ft930427_2350_1950G301370H.fits[3] ft930427_2350_1950G301470H.fits[3] ft930427_2350_1950G301670M.fits[3] ft930427_2350_1950G301770H.fits[3] ft930427_2350_1950G301870H.fits[3] ft930427_2350_1950G301970H.fits[3] ft930427_2350_1950G302070H.fits[3] ft930427_2350_1950G302170M.fits[3] ft930427_2350_1950G302270M.fits[3] ft930427_2350_1950G302470M.fits[3] ft930427_2350_1950G302570M.fits[3] ft930427_2350_1950G302770M.fits[3] ft930427_2350_1950G302870H.fits[3] ft930427_2350_1950G302970H.fits[3] ft930427_2350_1950G303070H.fits[3] ft930427_2350_1950G303170H.fits[3] ft930427_2350_1950G303270M.fits[3] ft930427_2350_1950G303370M.fits[3] ft930427_2350_1950G303570M.fits[3] ft930427_2350_1950G303670M.fits[3] ft930427_2350_1950G303770H.fits[3] ft930427_2350_1950G303870H.fits[3] ft930427_2350_1950G303970H.fits[3] ft930427_2350_1950G304070H.fits[3] ft930427_2350_1950G304170H.fits[3] ft930427_2350_1950G304270H.fits[3] ft930427_2350_1950G304370M.fits[3] ft930427_2350_1950G304470M.fits[3] ft930427_2350_1950G304670M.fits[3] ft930427_2350_1950G304770M.fits[3] ft930427_2350_1950G304870H.fits[3] ft930427_2350_1950G304970H.fits[3] ft930427_2350_1950G305070H.fits[3] ft930427_2350_1950G305170H.fits[3] ft930427_2350_1950G305370H.fits[3] ft930427_2350_1950G305470H.fits[3] ft930427_2350_1950G306270H.fits[3] ft930427_2350_1950G306370H.fits[3] ft930427_2350_1950G306470H.fits[3] ft930427_2350_1950G306570H.fits[3] ft930427_2350_1950G306770H.fits[3] ft930427_2350_1950G306870H.fits[3] ft930427_2350_1950G306970H.fits[3] ft930427_2350_1950G307070H.fits[3] ft930427_2350_1950G307170H.fits[3] ft930427_2350_1950G307270H.fits[3] ft930427_2350_1950G307370H.fits[3] ft930427_2350_1950G307470H.fits[3] ft930427_2350_1950G307570H.fits[3] ft930427_2350_1950G307670H.fits[3] ft930427_2350_1950G307770H.fits[3] ft930427_2350_1950G307870H.fits[3] ft930427_2350_1950G308670H.fits[3] ft930427_2350_1950G308770H.fits[3] ft930427_2350_1950G308870H.fits[3] ft930427_2350_1950G308970H.fits[3] ft930427_2350_1950G309070H.fits[3] ft930427_2350_1950G309870H.fits[3] ft930427_2350_1950G309970H.fits[3] ft930427_2350_1950G310070H.fits[3] ft930427_2350_1950G310170H.fits[3] ft930427_2350_1950G310670M.fits[3] ft930427_2350_1950G310770M.fits[3] ft930427_2350_1950G310870H.fits[3] ft930427_2350_1950G310970H.fits[3] ft930427_2350_1950G311070H.fits[3] ft930427_2350_1950G311170H.fits[3] ft930428_1949_2350G300170M.fits[3] ft930428_1949_2350G300270M.fits[3] ft930428_1949_2350G300470M.fits[3] ft930428_1949_2350G300570M.fits[3] ft930428_1949_2350G300670M.fits[3] ft930428_1949_2350G300970M.fits[3] ft930428_1949_2350G301070H.fits[3] ft930428_1949_2350G301170H.fits[3] ft930428_1949_2350G301270H.fits[3] ft930428_1949_2350G301370H.fits[3] ft930428_1949_2350G301470M.fits[3] ft930428_1949_2350G301570M.fits[3]
GISSORTCODE:LO:Start program GISSORTCODE:LO:End program-> Standard Error Output From STOOL gissortsplit:
GISSORTSPLIT:LO:Start program GISSORTSPLIT:LO:g200170h.prelist merge count = 3 photon cnt = 14 GISSORTSPLIT:LO:g200270h.prelist merge count = 2 photon cnt = 3 GISSORTSPLIT:LO:g200370h.prelist merge count = 3 photon cnt = 16 GISSORTSPLIT:LO:g200470h.prelist merge count = 3 photon cnt = 9 GISSORTSPLIT:LO:g200570h.prelist merge count = 1 photon cnt = 9 GISSORTSPLIT:LO:g200670h.prelist merge count = 14 photon cnt = 60324 GISSORTSPLIT:LO:g200770h.prelist merge count = 1 photon cnt = 13 GISSORTSPLIT:LO:g200870h.prelist merge count = 7 photon cnt = 47 GISSORTSPLIT:LO:g200970h.prelist merge count = 1 photon cnt = 5 GISSORTSPLIT:LO:g201070h.prelist merge count = 1 photon cnt = 5 GISSORTSPLIT:LO:g201170h.prelist merge count = 1 photon cnt = 2 GISSORTSPLIT:LO:g201270h.prelist merge count = 1 photon cnt = 2 GISSORTSPLIT:LO:g201370h.prelist merge count = 1 photon cnt = 11 GISSORTSPLIT:LO:g201470h.prelist merge count = 1 photon cnt = 9 GISSORTSPLIT:LO:g201570h.prelist merge count = 1 photon cnt = 4 GISSORTSPLIT:LO:g201670h.prelist merge count = 1 photon cnt = 2 GISSORTSPLIT:LO:g201770h.prelist merge count = 1 photon cnt = 6 GISSORTSPLIT:LO:g201870h.prelist merge count = 1 photon cnt = 4 GISSORTSPLIT:LO:g201970h.prelist merge count = 1 photon cnt = 5 GISSORTSPLIT:LO:g202070h.prelist merge count = 1 photon cnt = 4 GISSORTSPLIT:LO:g202170h.prelist merge count = 1 photon cnt = 2 GISSORTSPLIT:LO:g202270h.prelist merge count = 1 photon cnt = 8 GISSORTSPLIT:LO:g200170l.prelist merge count = 1 photon cnt = 4648 GISSORTSPLIT:LO:g200170m.prelist merge count = 3 photon cnt = 19 GISSORTSPLIT:LO:g200270m.prelist merge count = 4 photon cnt = 148 GISSORTSPLIT:LO:g200370m.prelist merge count = 9 photon cnt = 82925 GISSORTSPLIT:LO:g200470m.prelist merge count = 4 photon cnt = 246 GISSORTSPLIT:LO:Total filenames split = 69 GISSORTSPLIT:LO:Total split file cnt = 27 GISSORTSPLIT:LO:End program-> Creating ad50006000g200170m.unf
---- cmerge: version 1.5 ---- A total of 9 fits files ...... Sorting files using KEY: TSTART ... Checking GTI overlap in input files ... Merging binary extension #: 1 1 -- ft930427_2350_1950G200170M.fits 2 -- ft930427_2350_1950G200470M.fits 3 -- ft930427_2350_1950G201070M.fits 4 -- ft930427_2350_1950G201670M.fits 5 -- ft930427_2350_1950G202570M.fits 6 -- ft930427_2350_1950G202770M.fits 7 -- ft930427_2350_1950G203670M.fits 8 -- ft930427_2350_1950G204770M.fits 9 -- ft930427_2350_1950G209970M.fits Merging binary extension #: 2 1 -- ft930427_2350_1950G200170M.fits 2 -- ft930427_2350_1950G200470M.fits 3 -- ft930427_2350_1950G201070M.fits 4 -- ft930427_2350_1950G201670M.fits 5 -- ft930427_2350_1950G202570M.fits 6 -- ft930427_2350_1950G202770M.fits 7 -- ft930427_2350_1950G203670M.fits 8 -- ft930427_2350_1950G204770M.fits 9 -- ft930427_2350_1950G209970M.fits Checking the output file ... Extention # 1 ...... OK Extention # 2 ...... OK The program appears to have finished successfully!-> Creating ad50006000g200270h.unf
---- cmerge: version 1.5 ---- A total of 14 fits files ...... Sorting files using KEY: TSTART ... Checking GTI overlap in input files ... Merging binary extension #: 1 1 -- ft930427_2350_1950G200870H.fits 2 -- ft930427_2350_1950G201470H.fits 3 -- ft930427_2350_1950G202070H.fits 4 -- ft930427_2350_1950G203170H.fits 5 -- ft930427_2350_1950G204070H.fits 6 -- ft930427_2350_1950G204270H.fits 7 -- ft930427_2350_1950G205170H.fits 8 -- ft930427_2350_1950G205370H.fits 9 -- ft930427_2350_1950G206570H.fits 10 -- ft930427_2350_1950G206770H.fits 11 -- ft930427_2350_1950G207970H.fits 12 -- ft930427_2350_1950G209170H.fits 13 -- ft930427_2350_1950G209370H.fits 14 -- ft930427_2350_1950G210370H.fits Merging binary extension #: 2 1 -- ft930427_2350_1950G200870H.fits 2 -- ft930427_2350_1950G201470H.fits 3 -- ft930427_2350_1950G202070H.fits 4 -- ft930427_2350_1950G203170H.fits 5 -- ft930427_2350_1950G204070H.fits 6 -- ft930427_2350_1950G204270H.fits 7 -- ft930427_2350_1950G205170H.fits 8 -- ft930427_2350_1950G205370H.fits 9 -- ft930427_2350_1950G206570H.fits 10 -- ft930427_2350_1950G206770H.fits 11 -- ft930427_2350_1950G207970H.fits 12 -- ft930427_2350_1950G209170H.fits 13 -- ft930427_2350_1950G209370H.fits 14 -- ft930427_2350_1950G210370H.fits Checking the output file ... Extention # 1 ...... OK Extention # 2 ...... OK The program appears to have finished successfully!-> Checking ft930427_2350_1950G200270L.fits
---- cmerge: version 1.5 ---- A total of 1 fits files ...... Sorting files using KEY: TSTART ... Checking GTI overlap in input files ... Merging binary extension #: 1 1 -- ft930427_2350_1950G200270L.fits Merging binary extension #: 2 1 -- ft930427_2350_1950G200270L.fits Checking the output file ... Extention # 1 ...... OK Extention # 2 ...... OK The program appears to have finished successfully!-> Ignoring the following files containing 000000246 events
ft930427_2350_1950G200970M.fits ft930427_2350_1950G202170M.fits ft930427_2350_1950G203270M.fits ft930427_2350_1950G204370M.fits-> Ignoring the following files containing 000000148 events
ft930427_2350_1950G202470M.fits ft930427_2350_1950G203570M.fits ft930427_2350_1950G204670M.fits ft930427_2350_1950G209870M.fits-> Ignoring the following files containing 000000047 events
ft930427_2350_1950G200770H.fits ft930427_2350_1950G201370H.fits ft930427_2350_1950G201970H.fits ft930427_2350_1950G203070H.fits ft930427_2350_1950G203970H.fits ft930427_2350_1950G205070H.fits ft930427_2350_1950G210270H.fits-> Ignoring the following files containing 000000019 events
ft930427_2350_1950G202270M.fits ft930427_2350_1950G203370M.fits ft930427_2350_1950G204470M.fits-> Ignoring the following files containing 000000016 events
ft930427_2350_1950G206370H.fits ft930427_2350_1950G207770H.fits ft930427_2350_1950G208970H.fits-> Ignoring the following files containing 000000014 events
ft930427_2350_1950G205470H.fits ft930427_2350_1950G206870H.fits ft930427_2350_1950G208070H.fits-> Ignoring the following files containing 000000013 events
ft930427_2350_1950G209270H.fits-> Ignoring the following files containing 000000011 events
ft930427_2350_1950G202870H.fits-> Ignoring the following files containing 000000009 events
ft930427_2350_1950G202970H.fits-> Ignoring the following files containing 000000009 events
ft930427_2350_1950G204170H.fits-> Ignoring the following files containing 000000009 events
ft930427_2350_1950G206470H.fits ft930427_2350_1950G207870H.fits ft930427_2350_1950G209070H.fits-> Ignoring the following files containing 000000008 events
ft930427_2350_1950G201270H.fits-> Ignoring the following files containing 000000006 events
ft930427_2350_1950G201770H.fits-> Ignoring the following files containing 000000005 events
ft930427_2350_1950G210070H.fits-> Ignoring the following files containing 000000005 events
ft930427_2350_1950G204970H.fits-> Ignoring the following files containing 000000005 events
ft930427_2350_1950G204870H.fits-> Ignoring the following files containing 000000004 events
ft930427_2350_1950G210170H.fits-> Ignoring the following files containing 000000004 events
ft930427_2350_1950G201870H.fits-> Ignoring the following files containing 000000004 events
ft930427_2350_1950G200570H.fits-> Ignoring the following files containing 000000003 events
ft930427_2350_1950G206270H.fits ft930427_2350_1950G208870H.fits-> Ignoring the following files containing 000000002 events
ft930427_2350_1950G201170H.fits-> Ignoring the following files containing 000000002 events
ft930427_2350_1950G200670H.fits-> Ignoring the following files containing 000000002 events
ft930427_2350_1950G203870H.fits-> Ignoring the following files containing 000000002 events
ft930427_2350_1950G203770H.fits-> Collecting GIS3 event files by mode
GISSORTCODE:LO:Start program GISSORTCODE:LO:End program-> Standard Error Output From STOOL gissortsplit:
GISSORTSPLIT:LO:Start program GISSORTSPLIT:LO:g300170h.prelist merge count = 1 photon cnt = 4 GISSORTSPLIT:LO:g300270h.prelist merge count = 3 photon cnt = 16 GISSORTSPLIT:LO:g300370h.prelist merge count = 3 photon cnt = 7 GISSORTSPLIT:LO:g300470h.prelist merge count = 3 photon cnt = 15 GISSORTSPLIT:LO:g300570h.prelist merge count = 3 photon cnt = 19 GISSORTSPLIT:LO:g300670h.prelist merge count = 1 photon cnt = 3 GISSORTSPLIT:LO:g300770h.prelist merge count = 1 photon cnt = 5 GISSORTSPLIT:LO:g300870h.prelist merge count = 1 photon cnt = 7 GISSORTSPLIT:LO:g300970h.prelist merge count = 1 photon cnt = 3 GISSORTSPLIT:LO:g301070h.prelist merge count = 1 photon cnt = 1 GISSORTSPLIT:LO:g301170h.prelist merge count = 14 photon cnt = 57073 GISSORTSPLIT:LO:g301270h.prelist merge count = 7 photon cnt = 49 GISSORTSPLIT:LO:g301370h.prelist merge count = 1 photon cnt = 5 GISSORTSPLIT:LO:g301470h.prelist merge count = 1 photon cnt = 4 GISSORTSPLIT:LO:g301570h.prelist merge count = 1 photon cnt = 7 GISSORTSPLIT:LO:g301670h.prelist merge count = 1 photon cnt = 8 GISSORTSPLIT:LO:g301770h.prelist merge count = 1 photon cnt = 3 GISSORTSPLIT:LO:g301870h.prelist merge count = 1 photon cnt = 2 GISSORTSPLIT:LO:g301970h.prelist merge count = 1 photon cnt = 5 GISSORTSPLIT:LO:g302070h.prelist merge count = 1 photon cnt = 13 GISSORTSPLIT:LO:g302170h.prelist merge count = 1 photon cnt = 12 GISSORTSPLIT:LO:g302270h.prelist merge count = 1 photon cnt = 11 GISSORTSPLIT:LO:g302370h.prelist merge count = 1 photon cnt = 7 GISSORTSPLIT:LO:g302470h.prelist merge count = 1 photon cnt = 5 GISSORTSPLIT:LO:g302570h.prelist merge count = 1 photon cnt = 2 GISSORTSPLIT:LO:g302670h.prelist merge count = 1 photon cnt = 4 GISSORTSPLIT:LO:g302770h.prelist merge count = 1 photon cnt = 9 GISSORTSPLIT:LO:g302870h.prelist merge count = 1 photon cnt = 6 GISSORTSPLIT:LO:g302970h.prelist merge count = 1 photon cnt = 8 GISSORTSPLIT:LO:g300170l.prelist merge count = 1 photon cnt = 4709 GISSORTSPLIT:LO:g300170m.prelist merge count = 3 photon cnt = 22 GISSORTSPLIT:LO:g300270m.prelist merge count = 4 photon cnt = 116 GISSORTSPLIT:LO:g300370m.prelist merge count = 9 photon cnt = 79675 GISSORTSPLIT:LO:g300470m.prelist merge count = 4 photon cnt = 259 GISSORTSPLIT:LO:Total filenames split = 77 GISSORTSPLIT:LO:Total split file cnt = 34 GISSORTSPLIT:LO:End program-> Creating ad50006000g300170m.unf
---- cmerge: version 1.5 ---- A total of 9 fits files ...... Sorting files using KEY: TSTART ... Checking GTI overlap in input files ... Merging binary extension #: 1 1 -- ft930427_2350_1950G300170M.fits 2 -- ft930427_2350_1950G300470M.fits 3 -- ft930427_2350_1950G301070M.fits 4 -- ft930427_2350_1950G301670M.fits 5 -- ft930427_2350_1950G302570M.fits 6 -- ft930427_2350_1950G302770M.fits 7 -- ft930427_2350_1950G303670M.fits 8 -- ft930427_2350_1950G304770M.fits 9 -- ft930427_2350_1950G310770M.fits Merging binary extension #: 2 1 -- ft930427_2350_1950G300170M.fits 2 -- ft930427_2350_1950G300470M.fits 3 -- ft930427_2350_1950G301070M.fits 4 -- ft930427_2350_1950G301670M.fits 5 -- ft930427_2350_1950G302570M.fits 6 -- ft930427_2350_1950G302770M.fits 7 -- ft930427_2350_1950G303670M.fits 8 -- ft930427_2350_1950G304770M.fits 9 -- ft930427_2350_1950G310770M.fits Checking the output file ... Extention # 1 ...... OK Extention # 2 ...... OK The program appears to have finished successfully!-> Creating ad50006000g300270h.unf
---- cmerge: version 1.5 ---- A total of 14 fits files ...... Sorting files using KEY: TSTART ... Checking GTI overlap in input files ... Merging binary extension #: 1 1 -- ft930427_2350_1950G300870H.fits 2 -- ft930427_2350_1950G301470H.fits 3 -- ft930427_2350_1950G302070H.fits 4 -- ft930427_2350_1950G303170H.fits 5 -- ft930427_2350_1950G304070H.fits 6 -- ft930427_2350_1950G304270H.fits 7 -- ft930427_2350_1950G305170H.fits 8 -- ft930427_2350_1950G305370H.fits 9 -- ft930427_2350_1950G306570H.fits 10 -- ft930427_2350_1950G306770H.fits 11 -- ft930427_2350_1950G307770H.fits 12 -- ft930427_2350_1950G308970H.fits 13 -- ft930427_2350_1950G310170H.fits 14 -- ft930427_2350_1950G311170H.fits Merging binary extension #: 2 1 -- ft930427_2350_1950G300870H.fits 2 -- ft930427_2350_1950G301470H.fits 3 -- ft930427_2350_1950G302070H.fits 4 -- ft930427_2350_1950G303170H.fits 5 -- ft930427_2350_1950G304070H.fits 6 -- ft930427_2350_1950G304270H.fits 7 -- ft930427_2350_1950G305170H.fits 8 -- ft930427_2350_1950G305370H.fits 9 -- ft930427_2350_1950G306570H.fits 10 -- ft930427_2350_1950G306770H.fits 11 -- ft930427_2350_1950G307770H.fits 12 -- ft930427_2350_1950G308970H.fits 13 -- ft930427_2350_1950G310170H.fits 14 -- ft930427_2350_1950G311170H.fits Checking the output file ... Extention # 1 ...... OK Extention # 2 ...... OK The program appears to have finished successfully!-> Checking ft930427_2350_1950G300270L.fits
---- cmerge: version 1.5 ---- A total of 1 fits files ...... Sorting files using KEY: TSTART ... Checking GTI overlap in input files ... Merging binary extension #: 1 1 -- ft930427_2350_1950G300270L.fits Merging binary extension #: 2 1 -- ft930427_2350_1950G300270L.fits Checking the output file ... Extention # 1 ...... OK Extention # 2 ...... OK The program appears to have finished successfully!-> Ignoring the following files containing 000000259 events
ft930427_2350_1950G300970M.fits ft930427_2350_1950G302170M.fits ft930427_2350_1950G303270M.fits ft930427_2350_1950G304370M.fits-> Ignoring the following files containing 000000116 events
ft930427_2350_1950G302470M.fits ft930427_2350_1950G303570M.fits ft930427_2350_1950G304670M.fits ft930427_2350_1950G310670M.fits-> Ignoring the following files containing 000000049 events
ft930427_2350_1950G300770H.fits ft930427_2350_1950G301370H.fits ft930427_2350_1950G301970H.fits ft930427_2350_1950G303070H.fits ft930427_2350_1950G303970H.fits ft930427_2350_1950G305070H.fits ft930427_2350_1950G311070H.fits-> Ignoring the following files containing 000000022 events
ft930427_2350_1950G302270M.fits ft930427_2350_1950G303370M.fits ft930427_2350_1950G304470M.fits-> Ignoring the following files containing 000000019 events
ft930427_2350_1950G306470H.fits ft930427_2350_1950G308870H.fits ft930427_2350_1950G310070H.fits-> Ignoring the following files containing 000000016 events
ft930427_2350_1950G305470H.fits ft930427_2350_1950G307870H.fits ft930427_2350_1950G309070H.fits-> Ignoring the following files containing 000000015 events
ft930427_2350_1950G306370H.fits ft930427_2350_1950G308770H.fits ft930427_2350_1950G309970H.fits-> Ignoring the following files containing 000000013 events
ft930427_2350_1950G302870H.fits-> Ignoring the following files containing 000000012 events
ft930427_2350_1950G302970H.fits-> Ignoring the following files containing 000000011 events
ft930427_2350_1950G304870H.fits-> Ignoring the following files containing 000000009 events
ft930427_2350_1950G307370H.fits-> Ignoring the following files containing 000000008 events
ft930427_2350_1950G307070H.fits-> Ignoring the following files containing 000000008 events
ft930427_2350_1950G310870H.fits-> Ignoring the following files containing 000000007 events
ft930427_2350_1950G304970H.fits-> Ignoring the following files containing 000000007 events
ft930427_2350_1950G301270H.fits-> Ignoring the following files containing 000000007 events
ft930427_2350_1950G307270H.fits-> Ignoring the following files containing 000000007 events
ft930427_2350_1950G306270H.fits ft930427_2350_1950G308670H.fits ft930427_2350_1950G309870H.fits-> Ignoring the following files containing 000000006 events
ft930427_2350_1950G306870H.fits-> Ignoring the following files containing 000000005 events
ft930427_2350_1950G301770H.fits-> Ignoring the following files containing 000000005 events
ft930427_2350_1950G303870H.fits-> Ignoring the following files containing 000000005 events
ft930427_2350_1950G300570H.fits-> Ignoring the following files containing 000000005 events
ft930427_2350_1950G307470H.fits-> Ignoring the following files containing 000000004 events
ft930427_2350_1950G306970H.fits-> Ignoring the following files containing 000000004 events
ft930427_2350_1950G301170H.fits-> Ignoring the following files containing 000000004 events
ft930427_2350_1950G307170H.fits-> Ignoring the following files containing 000000003 events
ft930427_2350_1950G310970H.fits-> Ignoring the following files containing 000000003 events
ft930427_2350_1950G307670H.fits-> Ignoring the following files containing 000000003 events
ft930427_2350_1950G307570H.fits-> Ignoring the following files containing 000000002 events
ft930427_2350_1950G301870H.fits-> Ignoring the following files containing 000000002 events
ft930427_2350_1950G303770H.fits-> Ignoring the following files containing 000000001 events
ft930427_2350_1950G304170H.fits-> Collecting SIS0 event files by mode
SIS0SORTCODE:LO:Start program SIS0SORTCODE:LO:End program-> Standard Error Output From STOOL sis0sortsplit:
SIS0SORTSPLIT:LO:Start program SIS0SORTSPLIT:LO:s000101h.prelist merge count = 1 photon cnt = 23641 SIS0SORTSPLIT:LO:s000201h.prelist merge count = 12 photon cnt = 268718 SIS0SORTSPLIT:LO:s000301h.prelist merge count = 1 photon cnt = 113 SIS0SORTSPLIT:LO:s000401h.prelist merge count = 1 photon cnt = 36 SIS0SORTSPLIT:LO:s000501h.prelist merge count = 1 photon cnt = 26 SIS0SORTSPLIT:LO:s000601h.prelist merge count = 1 photon cnt = 13 SIS0SORTSPLIT:LO:s000701h.prelist merge count = 1 photon cnt = 256 SIS0SORTSPLIT:LO:s000801m.prelist merge count = 5 photon cnt = 127 SIS0SORTSPLIT:LO:s000902h.prelist merge count = 3 photon cnt = 886 SIS0SORTSPLIT:LO:s001002l.prelist merge count = 1 photon cnt = 2859 SIS0SORTSPLIT:LO:s001102m.prelist merge count = 18 photon cnt = 168750 SIS0SORTSPLIT:LO:s001202m.prelist merge count = 2 photon cnt = 20 SIS0SORTSPLIT:LO:Total filenames split = 47 SIS0SORTSPLIT:LO:Total split file cnt = 12 SIS0SORTSPLIT:LO:End program-> Creating ad50006000s000101h.unf
---- cmerge: version 1.5 ---- A total of 12 fits files ...... Sorting files using KEY: TSTART ... Checking GTI overlap in input files ... Merging binary extension #: 1 1 -- ft930427_2350_1950S000501H.fits 2 -- ft930427_2350_1950S000901H.fits 3 -- ft930427_2350_1950S001501H.fits 4 -- ft930427_2350_1950S002201H.fits 5 -- ft930427_2350_1950S002801H.fits 6 -- ft930427_2350_1950S003401H.fits 7 -- ft930427_2350_1950S003601H.fits 8 -- ft930427_2350_1950S004201H.fits 9 -- ft930427_2350_1950S004901H.fits 10 -- ft930427_2350_1950S005501H.fits 11 -- ft930427_2350_1950S006101H.fits 12 -- ft930427_2350_1950S006701H.fits Merging binary extension #: 2 1 -- ft930427_2350_1950S000501H.fits 2 -- ft930427_2350_1950S000901H.fits 3 -- ft930427_2350_1950S001501H.fits 4 -- ft930427_2350_1950S002201H.fits 5 -- ft930427_2350_1950S002801H.fits 6 -- ft930427_2350_1950S003401H.fits 7 -- ft930427_2350_1950S003601H.fits 8 -- ft930427_2350_1950S004201H.fits 9 -- ft930427_2350_1950S004901H.fits 10 -- ft930427_2350_1950S005501H.fits 11 -- ft930427_2350_1950S006101H.fits 12 -- ft930427_2350_1950S006701H.fits Checking the output file ... Extention # 1 ...... OK Extention # 2 ...... OK The program appears to have finished successfully!-> Creating ad50006000s000202m.unf
---- cmerge: version 1.5 ---- A total of 18 fits files ...... Sorting files using KEY: TSTART ... Checking GTI overlap in input files ... Merging binary extension #: 1 1 -- ft930427_2350_1950S000102M.fits 2 -- ft930427_2350_1950S000402M.fits 3 -- ft930427_2350_1950S000702M.fits 4 -- ft930427_2350_1950S001102M.fits 5 -- ft930427_2350_1950S001302M.fits 6 -- ft930427_2350_1950S001702M.fits 7 -- ft930427_2350_1950S001902M.fits 8 -- ft930427_2350_1950S002102M.fits 9 -- ft930427_2350_1950S002402M.fits 10 -- ft930427_2350_1950S002602M.fits 11 -- ft930427_2350_1950S003002M.fits 12 -- ft930427_2350_1950S003802M.fits 13 -- ft930427_2350_1950S004002M.fits 14 -- ft930427_2350_1950S005102M.fits 15 -- ft930427_2350_1950S005302M.fits 16 -- ft930427_2350_1950S005702M.fits 17 -- ft930427_2350_1950S005902M.fits 18 -- ft930427_2350_1950S006502M.fits Merging binary extension #: 2 1 -- ft930427_2350_1950S000102M.fits 2 -- ft930427_2350_1950S000402M.fits 3 -- ft930427_2350_1950S000702M.fits 4 -- ft930427_2350_1950S001102M.fits 5 -- ft930427_2350_1950S001302M.fits 6 -- ft930427_2350_1950S001702M.fits 7 -- ft930427_2350_1950S001902M.fits 8 -- ft930427_2350_1950S002102M.fits 9 -- ft930427_2350_1950S002402M.fits 10 -- ft930427_2350_1950S002602M.fits 11 -- ft930427_2350_1950S003002M.fits 12 -- ft930427_2350_1950S003802M.fits 13 -- ft930427_2350_1950S004002M.fits 14 -- ft930427_2350_1950S005102M.fits 15 -- ft930427_2350_1950S005302M.fits 16 -- ft930427_2350_1950S005702M.fits 17 -- ft930427_2350_1950S005902M.fits 18 -- ft930427_2350_1950S006502M.fits Checking the output file ... Extention # 1 ...... OK Extention # 2 ...... OK The program appears to have finished successfully!-> Checking ft930427_2350_1950S004401H.fits
---- cmerge: version 1.5 ---- A total of 1 fits files ...... Sorting files using KEY: TSTART ... Checking GTI overlap in input files ... Merging binary extension #: 1 1 -- ft930427_2350_1950S004401H.fits Merging binary extension #: 2 1 -- ft930427_2350_1950S004401H.fits Checking the output file ... Extention # 1 ...... OK Extention # 2 ...... OK The program appears to have finished successfully!-> Checking ft930427_2350_1950S000202L.fits
---- cmerge: version 1.5 ---- A total of 1 fits files ...... Sorting files using KEY: TSTART ... Checking GTI overlap in input files ... Merging binary extension #: 1 1 -- ft930427_2350_1950S000202L.fits Merging binary extension #: 2 1 -- ft930427_2350_1950S000202L.fits Checking the output file ... Extention # 1 ...... OK Extention # 2 ...... OK The program appears to have finished successfully!-> Ignoring the following files containing 000000886 events
ft930427_2350_1950S004102H.fits ft930427_2350_1950S005402H.fits ft930427_2350_1950S006002H.fits-> Ignoring the following files containing 000000256 events
ft930427_2350_1950S006201H.fits-> Ignoring the following files containing 000000127 events
ft930427_2350_1950S000801M.fits ft930427_2350_1950S001401M.fits ft930427_2350_1950S002701M.fits ft930427_2350_1950S003301M.fits ft930427_2350_1950S006601M.fits-> Ignoring the following files containing 000000113 events
ft930427_2350_1950S004801H.fits-> Ignoring the following files containing 000000036 events
ft930427_2350_1950S004501H.fits-> Ignoring the following files containing 000000026 events
ft930427_2350_1950S004701H.fits-> Ignoring the following files containing 000000020 events
ft930427_2350_1950S001802M.fits ft930427_2350_1950S003902M.fits-> Ignoring the following files containing 000000013 events
ft930427_2350_1950S004601H.fits-> Collecting SIS1 event files by mode
SIS1SORTCODE:LO:Start program SIS1SORTCODE:LO:End program-> Standard Error Output From STOOL sis1sortsplit:
SIS1SORTSPLIT:LO:Start program SIS1SORTSPLIT:LO:s100101h.prelist merge count = 1 photon cnt = 34 SIS1SORTSPLIT:LO:s100201h.prelist merge count = 1 photon cnt = 45 SIS1SORTSPLIT:LO:s100301h.prelist merge count = 13 photon cnt = 312546 SIS1SORTSPLIT:LO:s100401h.prelist merge count = 1 photon cnt = 40 SIS1SORTSPLIT:LO:s100501h.prelist merge count = 1 photon cnt = 256 SIS1SORTSPLIT:LO:s100601m.prelist merge count = 5 photon cnt = 160 SIS1SORTSPLIT:LO:s100702h.prelist merge count = 3 photon cnt = 1052 SIS1SORTSPLIT:LO:s100802l.prelist merge count = 1 photon cnt = 5104 SIS1SORTSPLIT:LO:s100902m.prelist merge count = 18 photon cnt = 197039 SIS1SORTSPLIT:LO:s101002m.prelist merge count = 2 photon cnt = 35 SIS1SORTSPLIT:LO:Total filenames split = 46 SIS1SORTSPLIT:LO:Total split file cnt = 10 SIS1SORTSPLIT:LO:End program-> Creating ad50006000s100101h.unf
---- cmerge: version 1.5 ---- A total of 13 fits files ...... Sorting files using KEY: TSTART ... Checking GTI overlap in input files ... Merging binary extension #: 1 1 -- ft930427_2350_1950S100501H.fits 2 -- ft930427_2350_1950S100901H.fits 3 -- ft930427_2350_1950S101501H.fits 4 -- ft930427_2350_1950S102201H.fits 5 -- ft930427_2350_1950S102801H.fits 6 -- ft930427_2350_1950S103401H.fits 7 -- ft930427_2350_1950S103601H.fits 8 -- ft930427_2350_1950S104101H.fits 9 -- ft930427_2350_1950S104301H.fits 10 -- ft930427_2350_1950S104701H.fits 11 -- ft930427_2350_1950S105301H.fits 12 -- ft930427_2350_1950S105901H.fits 13 -- ft930427_2350_1950S106501H.fits Merging binary extension #: 2 1 -- ft930427_2350_1950S100501H.fits 2 -- ft930427_2350_1950S100901H.fits 3 -- ft930427_2350_1950S101501H.fits 4 -- ft930427_2350_1950S102201H.fits 5 -- ft930427_2350_1950S102801H.fits 6 -- ft930427_2350_1950S103401H.fits 7 -- ft930427_2350_1950S103601H.fits 8 -- ft930427_2350_1950S104101H.fits 9 -- ft930427_2350_1950S104301H.fits 10 -- ft930427_2350_1950S104701H.fits 11 -- ft930427_2350_1950S105301H.fits 12 -- ft930427_2350_1950S105901H.fits 13 -- ft930427_2350_1950S106501H.fits Checking the output file ... Extention # 1 ...... OK Extention # 2 ...... OK The program appears to have finished successfully!-> Creating ad50006000s100202m.unf
---- cmerge: version 1.5 ---- A total of 18 fits files ...... Sorting files using KEY: TSTART ... Checking GTI overlap in input files ... Merging binary extension #: 1 1 -- ft930427_2350_1950S100102M.fits 2 -- ft930427_2350_1950S100402M.fits 3 -- ft930427_2350_1950S100702M.fits 4 -- ft930427_2350_1950S101102M.fits 5 -- ft930427_2350_1950S101302M.fits 6 -- ft930427_2350_1950S101702M.fits 7 -- ft930427_2350_1950S101902M.fits 8 -- ft930427_2350_1950S102102M.fits 9 -- ft930427_2350_1950S102402M.fits 10 -- ft930427_2350_1950S102602M.fits 11 -- ft930427_2350_1950S103002M.fits 12 -- ft930427_2350_1950S103702M.fits 13 -- ft930427_2350_1950S103902M.fits 14 -- ft930427_2350_1950S104902M.fits 15 -- ft930427_2350_1950S105102M.fits 16 -- ft930427_2350_1950S105502M.fits 17 -- ft930427_2350_1950S105702M.fits 18 -- ft930427_2350_1950S106302M.fits Merging binary extension #: 2 1 -- ft930427_2350_1950S100102M.fits 2 -- ft930427_2350_1950S100402M.fits 3 -- ft930427_2350_1950S100702M.fits 4 -- ft930427_2350_1950S101102M.fits 5 -- ft930427_2350_1950S101302M.fits 6 -- ft930427_2350_1950S101702M.fits 7 -- ft930427_2350_1950S101902M.fits 8 -- ft930427_2350_1950S102102M.fits 9 -- ft930427_2350_1950S102402M.fits 10 -- ft930427_2350_1950S102602M.fits 11 -- ft930427_2350_1950S103002M.fits 12 -- ft930427_2350_1950S103702M.fits 13 -- ft930427_2350_1950S103902M.fits 14 -- ft930427_2350_1950S104902M.fits 15 -- ft930427_2350_1950S105102M.fits 16 -- ft930427_2350_1950S105502M.fits 17 -- ft930427_2350_1950S105702M.fits 18 -- ft930427_2350_1950S106302M.fits Checking the output file ... Extention # 1 ...... OK Extention # 2 ...... OK The program appears to have finished successfully!-> Checking ft930427_2350_1950S100202L.fits
---- cmerge: version 1.5 ---- A total of 1 fits files ...... Sorting files using KEY: TSTART ... Checking GTI overlap in input files ... Merging binary extension #: 1 1 -- ft930427_2350_1950S100202L.fits Merging binary extension #: 2 1 -- ft930427_2350_1950S100202L.fits Checking the output file ... Extention # 1 ...... OK Extention # 2 ...... OK The program appears to have finished successfully!-> Creating ad50006000s100402h.unf
---- cmerge: version 1.5 ---- A total of 3 fits files ...... Sorting files using KEY: TSTART ... Checking GTI overlap in input files ... Merging binary extension #: 1 1 -- ft930427_2350_1950S104002H.fits 2 -- ft930427_2350_1950S105202H.fits 3 -- ft930427_2350_1950S105802H.fits Merging binary extension #: 2 1 -- ft930427_2350_1950S104002H.fits 2 -- ft930427_2350_1950S105202H.fits 3 -- ft930427_2350_1950S105802H.fits Checking the output file ... Extention # 1 ...... OK Extention # 2 ...... OK The program appears to have finished successfully!-> Ignoring the following files containing 000000256 events
ft930427_2350_1950S106001H.fits-> Ignoring the following files containing 000000160 events
ft930427_2350_1950S100801M.fits ft930427_2350_1950S101401M.fits ft930427_2350_1950S102701M.fits ft930427_2350_1950S103301M.fits ft930427_2350_1950S106401M.fits-> Ignoring the following files containing 000000045 events
ft930427_2350_1950S104501H.fits-> Ignoring the following files containing 000000040 events
ft930427_2350_1950S104601H.fits-> Ignoring the following files containing 000000035 events
ft930427_2350_1950S101802M.fits ft930427_2350_1950S103802M.fits-> Ignoring the following files containing 000000034 events
ft930427_2350_1950S104401H.fits-> Collecting GIS2 event files by mode
GISSORTCODE:LO:Start program GISSORTCODE:LO:End program-> Standard Error Output From STOOL gissortsplit:
GISSORTSPLIT:LO:Start program GISSORTSPLIT:LO:g200170h.prelist merge count = 1 photon cnt = 3692 GISSORTSPLIT:LO:g200270h.prelist merge count = 1 photon cnt = 5 GISSORTSPLIT:LO:g200370h.prelist merge count = 1 photon cnt = 2 GISSORTSPLIT:LO:g200470h.prelist merge count = 1 photon cnt = 4 GISSORTSPLIT:LO:g200170m.prelist merge count = 2 photon cnt = 15 GISSORTSPLIT:LO:g200270m.prelist merge count = 1 photon cnt = 18 GISSORTSPLIT:LO:g200370m.prelist merge count = 4 photon cnt = 26977 GISSORTSPLIT:LO:g200470m.prelist merge count = 1 photon cnt = 81 GISSORTSPLIT:LO:Total filenames split = 12 GISSORTSPLIT:LO:Total split file cnt = 8 GISSORTSPLIT:LO:End program-> Creating ad50006000g200470m.unf
---- cmerge: version 1.5 ---- A total of 4 fits files ...... Sorting files using KEY: TSTART ... Checking GTI overlap in input files ... Merging binary extension #: 1 1 -- ft930428_1949_2350G200170M.fits 2 -- ft930428_1949_2350G200570M.fits 3 -- ft930428_1949_2350G200970M.fits 4 -- ft930428_1949_2350G201570M.fits Merging binary extension #: 2 1 -- ft930428_1949_2350G200170M.fits 2 -- ft930428_1949_2350G200570M.fits 3 -- ft930428_1949_2350G200970M.fits 4 -- ft930428_1949_2350G201570M.fits Checking the output file ... Extention # 1 ...... OK Extention # 2 ...... OK The program appears to have finished successfully!-> Checking ft930428_1949_2350G201370H.fits
---- cmerge: version 1.5 ---- A total of 1 fits files ...... Sorting files using KEY: TSTART ... Checking GTI overlap in input files ... Merging binary extension #: 1 1 -- ft930428_1949_2350G201370H.fits Merging binary extension #: 2 1 -- ft930428_1949_2350G201370H.fits Checking the output file ... Extention # 1 ...... OK Extention # 2 ...... OK The program appears to have finished successfully!-> Ignoring the following files containing 000000081 events
ft930428_1949_2350G201470M.fits-> Ignoring the following files containing 000000018 events
ft930428_1949_2350G200470M.fits-> Ignoring the following files containing 000000015 events
ft930428_1949_2350G200270M.fits ft930428_1949_2350G200670M.fits-> Ignoring the following files containing 000000005 events
ft930428_1949_2350G201270H.fits-> Ignoring the following files containing 000000004 events
ft930428_1949_2350G201170H.fits-> Ignoring the following files containing 000000002 events
ft930428_1949_2350G201070H.fits-> Collecting GIS3 event files by mode
GISSORTCODE:LO:Start program GISSORTCODE:LO:End program-> Standard Error Output From STOOL gissortsplit:
GISSORTSPLIT:LO:Start program GISSORTSPLIT:LO:g300170h.prelist merge count = 1 photon cnt = 3482 GISSORTSPLIT:LO:g300270h.prelist merge count = 1 photon cnt = 2 GISSORTSPLIT:LO:g300370h.prelist merge count = 1 photon cnt = 6 GISSORTSPLIT:LO:g300470h.prelist merge count = 1 photon cnt = 1 GISSORTSPLIT:LO:g300170m.prelist merge count = 2 photon cnt = 19 GISSORTSPLIT:LO:g300270m.prelist merge count = 1 photon cnt = 21 GISSORTSPLIT:LO:g300370m.prelist merge count = 4 photon cnt = 26610 GISSORTSPLIT:LO:g300470m.prelist merge count = 1 photon cnt = 98 GISSORTSPLIT:LO:Total filenames split = 12 GISSORTSPLIT:LO:Total split file cnt = 8 GISSORTSPLIT:LO:End program-> Creating ad50006000g300470m.unf
---- cmerge: version 1.5 ---- A total of 4 fits files ...... Sorting files using KEY: TSTART ... Checking GTI overlap in input files ... Merging binary extension #: 1 1 -- ft930428_1949_2350G300170M.fits 2 -- ft930428_1949_2350G300570M.fits 3 -- ft930428_1949_2350G300970M.fits 4 -- ft930428_1949_2350G301570M.fits Merging binary extension #: 2 1 -- ft930428_1949_2350G300170M.fits 2 -- ft930428_1949_2350G300570M.fits 3 -- ft930428_1949_2350G300970M.fits 4 -- ft930428_1949_2350G301570M.fits Checking the output file ... Extention # 1 ...... OK Extention # 2 ...... OK The program appears to have finished successfully!-> Checking ft930428_1949_2350G301370H.fits
---- cmerge: version 1.5 ---- A total of 1 fits files ...... Sorting files using KEY: TSTART ... Checking GTI overlap in input files ... Merging binary extension #: 1 1 -- ft930428_1949_2350G301370H.fits Merging binary extension #: 2 1 -- ft930428_1949_2350G301370H.fits Checking the output file ... Extention # 1 ...... OK Extention # 2 ...... OK The program appears to have finished successfully!-> Ignoring the following files containing 000000098 events
ft930428_1949_2350G301470M.fits-> Ignoring the following files containing 000000021 events
ft930428_1949_2350G300470M.fits-> Ignoring the following files containing 000000019 events
ft930428_1949_2350G300270M.fits ft930428_1949_2350G300670M.fits-> Ignoring the following files containing 000000006 events
ft930428_1949_2350G301070H.fits-> Ignoring the following files containing 000000002 events
ft930428_1949_2350G301270H.fits-> Ignoring the following files containing 000000001 events
ft930428_1949_2350G301170H.fits-> Collecting SIS0 event files by mode
SIS0SORTCODE:LO:Start program SIS0SORTCODE:LO:End program-> Standard Error Output From STOOL sis0sortsplit:
SIS0SORTSPLIT:LO:Start program SIS0SORTSPLIT:LO:s000101h.prelist merge count = 1 photon cnt = 15845 SIS0SORTSPLIT:LO:s000201m.prelist merge count = 1 photon cnt = 32 SIS0SORTSPLIT:LO:s000302m.prelist merge count = 4 photon cnt = 61343 SIS0SORTSPLIT:LO:Total filenames split = 6 SIS0SORTSPLIT:LO:Total split file cnt = 3 SIS0SORTSPLIT:LO:End program-> Creating ad50006000s000502m.unf
---- cmerge: version 1.5 ---- A total of 4 fits files ...... Sorting files using KEY: TSTART ... Checking GTI overlap in input files ... Merging binary extension #: 1 1 -- ft930428_1949_2350S000102M.fits 2 -- ft930428_1949_2350S000302M.fits 3 -- ft930428_1949_2350S000502M.fits 4 -- ft930428_1949_2350S000902M.fits Merging binary extension #: 2 1 -- ft930428_1949_2350S000102M.fits 2 -- ft930428_1949_2350S000302M.fits 3 -- ft930428_1949_2350S000502M.fits 4 -- ft930428_1949_2350S000902M.fits Checking the output file ... Extention # 1 ...... OK Extention # 2 ...... OK The program appears to have finished successfully!-> Checking ft930428_1949_2350S000701H.fits
---- cmerge: version 1.5 ---- A total of 1 fits files ...... Sorting files using KEY: TSTART ... Checking GTI overlap in input files ... Merging binary extension #: 1 1 -- ft930428_1949_2350S000701H.fits Merging binary extension #: 2 1 -- ft930428_1949_2350S000701H.fits Checking the output file ... Extention # 1 ...... OK Extention # 2 ...... OK The program appears to have finished successfully!-> Ignoring the following files containing 000000032 events
ft930428_1949_2350S000601M.fits-> Collecting SIS1 event files by mode
SIS1SORTCODE:LO:Start program SIS1SORTCODE:LO:End program-> Standard Error Output From STOOL sis1sortsplit:
SIS1SORTSPLIT:LO:Start program SIS1SORTSPLIT:LO:s100101h.prelist merge count = 1 photon cnt = 18534 SIS1SORTSPLIT:LO:s100201m.prelist merge count = 1 photon cnt = 32 SIS1SORTSPLIT:LO:s100302m.prelist merge count = 4 photon cnt = 70315 SIS1SORTSPLIT:LO:Total filenames split = 6 SIS1SORTSPLIT:LO:Total split file cnt = 3 SIS1SORTSPLIT:LO:End program-> Creating ad50006000s100502m.unf
---- cmerge: version 1.5 ---- A total of 4 fits files ...... Sorting files using KEY: TSTART ... Checking GTI overlap in input files ... Merging binary extension #: 1 1 -- ft930428_1949_2350S100102M.fits 2 -- ft930428_1949_2350S100302M.fits 3 -- ft930428_1949_2350S100502M.fits 4 -- ft930428_1949_2350S100902M.fits Merging binary extension #: 2 1 -- ft930428_1949_2350S100102M.fits 2 -- ft930428_1949_2350S100302M.fits 3 -- ft930428_1949_2350S100502M.fits 4 -- ft930428_1949_2350S100902M.fits Checking the output file ... Extention # 1 ...... OK Extention # 2 ...... OK The program appears to have finished successfully!-> Checking ft930428_1949_2350S100701H.fits
---- cmerge: version 1.5 ---- A total of 1 fits files ...... Sorting files using KEY: TSTART ... Checking GTI overlap in input files ... Merging binary extension #: 1 1 -- ft930428_1949_2350S100701H.fits Merging binary extension #: 2 1 -- ft930428_1949_2350S100701H.fits Checking the output file ... Extention # 1 ...... OK Extention # 2 ...... OK The program appears to have finished successfully!-> Ignoring the following files containing 000000032 events
ft930428_1949_2350S100601M.fits-> Tar-ing together the leftover raw files
a ft930427_2350_1950G200570H.fits 40K a ft930427_2350_1950G200670H.fits 40K a ft930427_2350_1950G200770H.fits 40K a ft930427_2350_1950G200970M.fits 43K a ft930427_2350_1950G201170H.fits 40K a ft930427_2350_1950G201270H.fits 40K a ft930427_2350_1950G201370H.fits 40K a ft930427_2350_1950G201770H.fits 40K a ft930427_2350_1950G201870H.fits 40K a ft930427_2350_1950G201970H.fits 40K a ft930427_2350_1950G202170M.fits 40K a ft930427_2350_1950G202270M.fits 40K a ft930427_2350_1950G202470M.fits 40K a ft930427_2350_1950G202870H.fits 40K a ft930427_2350_1950G202970H.fits 40K a ft930427_2350_1950G203070H.fits 40K a ft930427_2350_1950G203270M.fits 40K a ft930427_2350_1950G203370M.fits 40K a ft930427_2350_1950G203570M.fits 40K a ft930427_2350_1950G203770H.fits 40K a ft930427_2350_1950G203870H.fits 40K a ft930427_2350_1950G203970H.fits 40K a ft930427_2350_1950G204170H.fits 40K a ft930427_2350_1950G204370M.fits 40K a ft930427_2350_1950G204470M.fits 40K a ft930427_2350_1950G204670M.fits 40K a ft930427_2350_1950G204870H.fits 40K a ft930427_2350_1950G204970H.fits 40K a ft930427_2350_1950G205070H.fits 40K a ft930427_2350_1950G205470H.fits 40K a ft930427_2350_1950G206270H.fits 40K a ft930427_2350_1950G206370H.fits 40K a ft930427_2350_1950G206470H.fits 40K a ft930427_2350_1950G206870H.fits 40K a ft930427_2350_1950G207770H.fits 40K a ft930427_2350_1950G207870H.fits 40K a ft930427_2350_1950G208070H.fits 40K a ft930427_2350_1950G208870H.fits 40K a ft930427_2350_1950G208970H.fits 40K a ft930427_2350_1950G209070H.fits 40K a ft930427_2350_1950G209270H.fits 40K a ft930427_2350_1950G209870M.fits 40K a ft930427_2350_1950G210070H.fits 40K a ft930427_2350_1950G210170H.fits 40K a ft930427_2350_1950G210270H.fits 40K a ft930427_2350_1950G300570H.fits 40K a ft930427_2350_1950G300770H.fits 40K a ft930427_2350_1950G300970M.fits 43K a ft930427_2350_1950G301170H.fits 40K a ft930427_2350_1950G301270H.fits 40K a ft930427_2350_1950G301370H.fits 40K a ft930427_2350_1950G301770H.fits 40K a ft930427_2350_1950G301870H.fits 40K a ft930427_2350_1950G301970H.fits 40K a ft930427_2350_1950G302170M.fits 40K a ft930427_2350_1950G302270M.fits 40K a ft930427_2350_1950G302470M.fits 40K a ft930427_2350_1950G302870H.fits 40K a ft930427_2350_1950G302970H.fits 40K a ft930427_2350_1950G303070H.fits 40K a ft930427_2350_1950G303270M.fits 40K a ft930427_2350_1950G303370M.fits 40K a ft930427_2350_1950G303570M.fits 40K a ft930427_2350_1950G303770H.fits 40K a ft930427_2350_1950G303870H.fits 40K a ft930427_2350_1950G303970H.fits 40K a ft930427_2350_1950G304170H.fits 40K a ft930427_2350_1950G304370M.fits 40K a ft930427_2350_1950G304470M.fits 40K a ft930427_2350_1950G304670M.fits 40K a ft930427_2350_1950G304870H.fits 40K a ft930427_2350_1950G304970H.fits 40K a ft930427_2350_1950G305070H.fits 40K a ft930427_2350_1950G305470H.fits 40K a ft930427_2350_1950G306270H.fits 40K a ft930427_2350_1950G306370H.fits 40K a ft930427_2350_1950G306470H.fits 40K a ft930427_2350_1950G306870H.fits 40K a ft930427_2350_1950G306970H.fits 40K a ft930427_2350_1950G307070H.fits 40K a ft930427_2350_1950G307170H.fits 40K a ft930427_2350_1950G307270H.fits 40K a ft930427_2350_1950G307370H.fits 40K a ft930427_2350_1950G307470H.fits 40K a ft930427_2350_1950G307570H.fits 40K a ft930427_2350_1950G307670H.fits 40K a ft930427_2350_1950G307870H.fits 40K a ft930427_2350_1950G308670H.fits 40K a ft930427_2350_1950G308770H.fits 40K a ft930427_2350_1950G308870H.fits 40K a ft930427_2350_1950G309070H.fits 40K a ft930427_2350_1950G309870H.fits 40K a ft930427_2350_1950G309970H.fits 40K a ft930427_2350_1950G310070H.fits 40K a ft930427_2350_1950G310670M.fits 40K a ft930427_2350_1950G310870H.fits 40K a ft930427_2350_1950G310970H.fits 40K a ft930427_2350_1950G311070H.fits 40K a ft930427_2350_1950S000801M.fits 40K a ft930427_2350_1950S001401M.fits 40K a ft930427_2350_1950S001802M.fits 40K a ft930427_2350_1950S002701M.fits 40K a ft930427_2350_1950S003301M.fits 40K a ft930427_2350_1950S003902M.fits 40K a ft930427_2350_1950S004102H.fits 45K a ft930427_2350_1950S004501H.fits 40K a ft930427_2350_1950S004601H.fits 40K a ft930427_2350_1950S004701H.fits 40K a ft930427_2350_1950S004801H.fits 43K a ft930427_2350_1950S005402H.fits 48K a ft930427_2350_1950S006002H.fits 48K a ft930427_2350_1950S006201H.fits 48K a ft930427_2350_1950S006601M.fits 40K a ft930427_2350_1950S100801M.fits 40K a ft930427_2350_1950S101401M.fits 40K a ft930427_2350_1950S101802M.fits 40K a ft930427_2350_1950S102701M.fits 40K a ft930427_2350_1950S103301M.fits 40K a ft930427_2350_1950S103802M.fits 40K a ft930427_2350_1950S104401H.fits 40K a ft930427_2350_1950S104501H.fits 40K a ft930427_2350_1950S104601H.fits 40K a ft930427_2350_1950S106001H.fits 48K a ft930427_2350_1950S106401M.fits 40K a ft930428_1949_2350G200270M.fits 40K a ft930428_1949_2350G200470M.fits 40K a ft930428_1949_2350G200670M.fits 40K a ft930428_1949_2350G201070H.fits 40K a ft930428_1949_2350G201170H.fits 40K a ft930428_1949_2350G201270H.fits 40K a ft930428_1949_2350G201470M.fits 40K a ft930428_1949_2350G300270M.fits 40K a ft930428_1949_2350G300470M.fits 40K a ft930428_1949_2350G300670M.fits 40K a ft930428_1949_2350G301070H.fits 40K a ft930428_1949_2350G301170H.fits 40K a ft930428_1949_2350G301270H.fits 40K a ft930428_1949_2350G301470M.fits 43K a ft930428_1949_2350S000601M.fits 40K a ft930428_1949_2350S100601M.fits 40K-> Checking OBJECT keywords in HK and event files
temp2gain v4.2 opening ft930427_2350.1950 'ft930427_2350.1950' is successfully opened Data Start Time is 10108230.72 (930427 235030) Time Margin 2.0 sec included Sync error detected in 338 th SF Sync error detected in 340 th SF Sync error detected in 15274 th SF 'ft930427_2350.1950' EOF detected, sf=15310 Data End Time is 10180202.50 (930428 195002) Gain History is written in ft930427_2350_1950.ghf-> Checking if column CAL_START in ft930427_2350_1950.ghf[1] is in order
Time column is TIME ORDERED-> Checking if column CAL_STOP in ft930427_2350_1950.ghf[1] is in order
Time column is TIME ORDERED-> Creating gain history file ft930428_1949_2350.ghf
temp2gain v4.2 opening ft930428_1949.2350 'ft930428_1949.2350' is successfully opened Data Start Time is 10180214.50 (930428 195014) Time Margin 2.0 sec included 'ft930428_1949.2350' EOF detected, sf=1573 Data End Time is 10194634.46 (930428 235034) Gain History is written in ft930428_1949_2350.ghf-> Checking if column CAL_START in ft930428_1949_2350.ghf[1] is in order
Time column is TIME ORDERED-> Checking if column CAL_STOP in ft930428_1949_2350.ghf[1] is in order
Time column is TIME ORDERED
ASCALIN_V0.9t-> Checking if ad50006000g200270h.unf is covered by attitude file
ASCALIN_V0.9t-> Checking if ad50006000g200370l.unf is covered by attitude file
ASCALIN_V0.9t-> Checking if ad50006000g200470m.unf is covered by attitude file
ASCALIN_V0.9t-> Checking if ad50006000g200570h.unf is covered by attitude file
ASCALIN_V0.9t-> Checking if ad50006000g300170m.unf is covered by attitude file
ASCALIN_V0.9t-> Checking if ad50006000g300270h.unf is covered by attitude file
ASCALIN_V0.9t-> Checking if ad50006000g300370l.unf is covered by attitude file
ASCALIN_V0.9t-> Checking if ad50006000g300470m.unf is covered by attitude file
ASCALIN_V0.9t-> Checking if ad50006000g300570h.unf is covered by attitude file
ASCALIN_V0.9t-> Checking if ad50006000s000101h.unf is covered by attitude file
ASCALIN_V0.9t-> Checking if ad50006000s000102h.unf is covered by attitude file
ASCALIN_V0.9t-> Checking if ad50006000s000112h.unf is covered by attitude file
ASCALIN_V0.9t-> Checking if ad50006000s000202m.unf is covered by attitude file
ASCALIN_V0.9t-> Checking if ad50006000s000301h.unf is covered by attitude file
ASCALIN_V0.9t-> Checking if ad50006000s000302h.unf is covered by attitude file
ASCALIN_V0.9t-> Checking if ad50006000s000312h.unf is covered by attitude file
ASCALIN_V0.9t-> Checking if ad50006000s000402l.unf is covered by attitude file
ASCALIN_V0.9t-> Checking if ad50006000s000502m.unf is covered by attitude file
ASCALIN_V0.9t-> Checking if ad50006000s000601h.unf is covered by attitude file
ASCALIN_V0.9t-> Checking if ad50006000s000602h.unf is covered by attitude file
ASCALIN_V0.9t-> Checking if ad50006000s000612h.unf is covered by attitude file
ASCALIN_V0.9t-> Checking if ad50006000s100101h.unf is covered by attitude file
ASCALIN_V0.9t-> Checking if ad50006000s100102h.unf is covered by attitude file
ASCALIN_V0.9t-> Checking if ad50006000s100112h.unf is covered by attitude file
ASCALIN_V0.9t-> Checking if ad50006000s100202m.unf is covered by attitude file
ASCALIN_V0.9t-> Checking if ad50006000s100302l.unf is covered by attitude file
ASCALIN_V0.9t-> Checking if ad50006000s100402h.unf is covered by attitude file
ASCALIN_V0.9t-> Checking if ad50006000s100502m.unf is covered by attitude file
ASCALIN_V0.9t-> Checking if ad50006000s100601h.unf is covered by attitude file
ASCALIN_V0.9t-> Checking if ad50006000s100602h.unf is covered by attitude file
ASCALIN_V0.9t-> Checking if ad50006000s100612h.unf is covered by attitude file
ASCALIN_V0.9t
Date and time are: 93/ 4/27 23:50 mjd=49104.993056 Orbit file name is ./frf.orbit.201 Epoch of Orbital Elements: 1993/4/26 20:0:0 Rigidity Data File: ./rigidity.data.1.23 Attitude FRF: fa930427_2350.1950 S0-HK file: ft930427_2350_1950S0HK.fits S1-HK file: ft930427_2350_1950S1HK.fits G2-HK file: ft930427_2350_1950G2HK.fits G3-HK file: ft930427_2350_1950G3HK.fits output FITS File: ft930427_2350_1950.mkf Total 2251 Data bins were processed.-> Checking if column TIME in ft930427_2350_1950.mkf is in order
Time column is TIME ORDERED-> Calculating dead time values for filter file
Date and time are: 93/ 4/28 19:49 mjd=49105.825694 Orbit file name is ./frf.orbit.201 Epoch of Orbital Elements: 1993/4/26 20:0:0 Rigidity Data File: ./rigidity.data.1.23 Attitude FRF: fa930428_1949.2350 S0-HK file: ft930428_1949_2350S0HK.fits S1-HK file: ft930428_1949_2350S1HK.fits G2-HK file: ft930428_1949_2350G2HK.fits G3-HK file: ft930428_1949_2350G3HK.fits output FITS File: ft930428_1949_2350.mkf Total 452 Data bins were processed.-> Checking if column TIME in ft930428_1949_2350.mkf is in order
Time column is TIME ORDERED-> Calculating dead time values for filter file
The sum of the selected column is 9089.2003 The mean of the selected column is 23.669792 The standard deviation of the selected column is 12.776437 The minimum of selected column is 8.4687748 The maximum of selected column is 173.12552 The number of points used in calculation is 384-> Standard Output From FTOOL fstatistic:
The sum of the selected column is 7017.8024 The mean of the selected column is 18.275527 The standard deviation of the selected column is 11.071046 The minimum of selected column is 5.2187653 The maximum of selected column is 110.06284 The number of points used in calculation is 384-> Standard Output From FTOOL fstatistic:
The sum of the selected column is 8898.7770 The mean of the selected column is 23.173898 The standard deviation of the selected column is 17.810232 The minimum of selected column is 5.0937648 The maximum of selected column is 269.90717 The number of points used in calculation is 384-> Standard Output From FTOOL fstatistic:
The sum of the selected column is 8558.9844 The mean of the selected column is 22.289022 The standard deviation of the selected column is 12.986495 The minimum of selected column is 4.7031527 The maximum of selected column is 133.46916 The number of points used in calculation is 384-> Using the following selection criteria:
(SAA==0) &&(BR_EARTH>20) &&(ELV>10) &&(COR>6) &&(ACS==0) &&(ANG_DIST>0)&& (ANG_DIST<0.01) &&(FOV==0) && ( (S0_PIXL0>0.0 && S0_PIXL0<61.9 )&& (S0_PIXL1>0.0 && S0_PIXL1<51.4 )&& (S0_PIXL2>0.0 && S0_PIXL2<76.6 )&& (S0_PIXL3>0.0 && S0_PIXL3<61.2 ) ) &&( (S0_SATF0<1) ||(S0_SATF0>1)) &&( (S0_SATF1<1) ||(S0_SATF1>1)) &&( (S0_SATF2<1) ||(S0_SATF2>1)) &&( (S0_SATF3<1) ||(S0_SATF3>1)) &&((T_DY_NT<0)||(T_DY_NT>64)) &&((T_SAA <0)||(T_SAA >64))-> Standard Output From FTOOL xselect:
** XSELECT V1.3 **
!> Enter session name >[xsel] screen
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS S0CCDPOW
1 W50 EAST BRIGHT HIGH 28/04/93 03:44:28 0.22E+05 152479 1111
Processing file: /data/data17/seq_proc/50006000.007/ad50006000s000102h.unf
EXTRACTOR vers 2.0 11 Apr 1997.
Doing file: /data/data17/seq_proc/50006000.007/screen_work1001.xsl
Total Good Bad: Region Time Phase Cut
149932 106641 0 43291 0 0
Writing events file
106641 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
149932 106641 0 43291 0 0
in 15568.82 seconds
CLEANSIS_V1.6
allocating image arrays...
PROGRAM TO MAKE AN SIS SCIENCE FILE CLEANED OF ANOMALOUS PIXELS.
* Anomalous pixels may consist of at least two populations.
1. Persistent HOT pixels are removed by comparing to the chip mean.
2. Flickering WARM pixels are removed by comparing to the cell mean.
3. In faint areas (zero bgd), flickering pixels are removed with a
cutoff threshold.
Hints:
Choose cell size and thresholds based on the expected background and the PSF.
Use the DIRTYSIS option to examine the anomalous pixel spectra.
Try a multiple pass clean:
Choose a PHA cut to optimize the S/N of the flickering pixels,
then a broad band clean.
Be suspicious of extended source cleans.
For very bright sources you may need to turn off the iteration option.
See the help page for further info (fhelp cleansis)
Poisson clean cell size : 5
Poisson probability threshold : 0.631E-05
Zero Bgd Cutoff threshold (>) : 3
Iterate : T
Dirtysis : F
Minimum PHA value (inclusive) : 0
Maximum PHA value (inclusive) : 4095
open output file: /data/data17/seq_proc/50006000.007/screen_in_event.xsl
reading data file: /data/data17/seq_proc/50006000.007/screen_out_event.xsl
copying primary header to output file...
making chip image...
File NEVENTS keyword value : 106641
Total counts in chip images : 106640
copy bad pix array...
cleaning chip # 0
Hot pixels & counts : 79 63194
Flickering pixels iter, pixels & cnts : 1 44 1811
cleaning chip # 1
Hot pixels & counts : 26 12308
Flickering pixels iter, pixels & cnts : 1 145 957
cleaning chip # 2
Hot pixels & counts : 26 7244
Flickering pixels iter, pixels & cnts : 1 63 733
cleaning chip # 3
Hot pixels & counts : 29 9919
Flickering pixels iter, pixels & cnts : 1 25 243
Number of pixels rejected : 437
Number of (internal) image counts : 106640
Number of image cts rejected (N, %) : 96409 90.4060364
By chip : 0 1 2 3
Pixels rejected : 123 171 89 54
Image counts : 68531 16487 10093 11529
Image cts rejected: 65005 13265 7977 10162
Image cts rej (%) : 94.85 80.46 79.03 88.14
filtering data...
Total counts : 68531 16487 10094 11529
Total cts rejected: 65005 13265 7978 10162
Total cts rej (%) : 94.85 80.46 79.04 88.14
Number of clean counts accepted : 10231
writing history cards...
copying extensions...
writing out hot pixs...
Number of rejected pixels : 437
updating NEVENTS keywords...
closing data file...
closing clean file...
Command not found; type ? for a command listing
!screen:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!screen:ASCA > set datadir .
Setting data directory to /data/data17/seq_proc/50006000.007/
Setting mkf directory to /data/data17/seq_proc/50006000.007/
!screen:ASCA > read events ad50006000s000102h.unf
Got new instrument: SIS0
Setting: IMAGE binning = 4
WMAP binning = 8
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 2047
Got the minimum time resolution of the read data: 16.000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data17/seq_proc/50006000.007/
HK Directory is: /data/data17/seq_proc/50006000.007/
!screen:ASCA-SIS0-BRIGHT > select event "grade==0||grade==2||grade==3||grade==4" save_file=no
!screen:ASCA-SIS0-BRIGHT > select mkf "@criteria.tmp" data_dir=. ASCA_mkf_def_expr=ft*.mkf
!screen:ASCA-SIS0-BRIGHT > extract events
!screen:ASCA-SIS0-BRIGHT > sisclean saoimage=no sis_plot=no clean=2 cellsize=5 log_prob=-5.24 bkg_thr=3 clean_phalow=0 clean_phahi=4095
!screen:ASCA-SIS0-BRIGHT > save clean outfile=ad50006000s000102h.evt use_events=no
Wrote cleaned events file to ad50006000s000102h.evt
!screen:ASCA-SIS0-BRIGHT > exit save_session=no
-> Filtering ad50006000s000112h.unf into ad50006000s000112h.evtThe sum of the selected column is 9089.2003 The mean of the selected column is 23.669792 The standard deviation of the selected column is 12.776437 The minimum of selected column is 8.4687748 The maximum of selected column is 173.12552 The number of points used in calculation is 384-> Standard Output From FTOOL fstatistic:
The sum of the selected column is 7017.8024 The mean of the selected column is 18.275527 The standard deviation of the selected column is 11.071046 The minimum of selected column is 5.2187653 The maximum of selected column is 110.06284 The number of points used in calculation is 384-> Standard Output From FTOOL fstatistic:
The sum of the selected column is 8898.7770 The mean of the selected column is 23.173898 The standard deviation of the selected column is 17.810232 The minimum of selected column is 5.0937648 The maximum of selected column is 269.90717 The number of points used in calculation is 384-> Standard Output From FTOOL fstatistic:
The sum of the selected column is 8558.9844 The mean of the selected column is 22.289022 The standard deviation of the selected column is 12.986495 The minimum of selected column is 4.7031527 The maximum of selected column is 133.46916 The number of points used in calculation is 384-> Using the following selection criteria:
(SAA==0) &&(BR_EARTH>20) &&(ELV>10) &&(COR>6) &&(ACS==0) &&(ANG_DIST>0)&& (ANG_DIST<0.01) &&(FOV==0) && ( (S0_PIXL0>0.0 && S0_PIXL0<61.9 )&& (S0_PIXL1>0.0 && S0_PIXL1<51.4 )&& (S0_PIXL2>0.0 && S0_PIXL2<76.6 )&& (S0_PIXL3>0.0 && S0_PIXL3<61.2 ) ) &&( (S0_SATF0<1) ||(S0_SATF0>1)) &&( (S0_SATF1<1) ||(S0_SATF1>1)) &&( (S0_SATF2<1) ||(S0_SATF2>1)) &&( (S0_SATF3<1) ||(S0_SATF3>1)) &&((T_DY_NT<0)||(T_DY_NT>64)) &&((T_SAA <0)||(T_SAA >64))-> Standard Output From FTOOL xselect:
** XSELECT V1.3 **
!> Enter session name >[xsel] screen
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS S0CCDPOW
1 W50 EAST BRIGHT2 HIGH 28/04/93 03:44:28 0.22E+05 159300 1111
Processing file: /data/data17/seq_proc/50006000.007/ad50006000s000112h.unf
EXTRACTOR vers 2.0 11 Apr 1997.
Doing file: /data/data17/seq_proc/50006000.007/screen_work1001.xsl
Total Good Bad: Region Time Phase Cut
150378 106967 0 43411 0 0
Writing events file
106967 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
150378 106967 0 43411 0 0
in 15568.82 seconds
CLEANSIS_V1.6
allocating image arrays...
PROGRAM TO MAKE AN SIS SCIENCE FILE CLEANED OF ANOMALOUS PIXELS.
* Anomalous pixels may consist of at least two populations.
1. Persistent HOT pixels are removed by comparing to the chip mean.
2. Flickering WARM pixels are removed by comparing to the cell mean.
3. In faint areas (zero bgd), flickering pixels are removed with a
cutoff threshold.
Hints:
Choose cell size and thresholds based on the expected background and the PSF.
Use the DIRTYSIS option to examine the anomalous pixel spectra.
Try a multiple pass clean:
Choose a PHA cut to optimize the S/N of the flickering pixels,
then a broad band clean.
Be suspicious of extended source cleans.
For very bright sources you may need to turn off the iteration option.
See the help page for further info (fhelp cleansis)
Poisson clean cell size : 5
Poisson probability threshold : 0.631E-05
Zero Bgd Cutoff threshold (>) : 3
Iterate : T
Dirtysis : F
Minimum PHA value (inclusive) : 0
Maximum PHA value (inclusive) : 4095
open output file: /data/data17/seq_proc/50006000.007/screen_in_event.xsl
reading data file: /data/data17/seq_proc/50006000.007/screen_out_event.xsl
copying primary header to output file...
making chip image...
Total counts in chip images : 106967
copy bad pix array...
cleaning chip # 0
Hot pixels & counts : 79 63219
Flickering pixels iter, pixels & cnts : 1 44 1817
cleaning chip # 1
Hot pixels & counts : 26 12308
Flickering pixels iter, pixels & cnts : 1 145 957
cleaning chip # 2
Hot pixels & counts : 26 7246
Flickering pixels iter, pixels & cnts : 1 63 737
cleaning chip # 3
Hot pixels & counts : 29 9925
Flickering pixels iter, pixels & cnts : 1 25 244
Number of pixels rejected : 437
Number of (internal) image counts : 106967
Number of image cts rejected (N, %) : 96453 90.1707993
By chip : 0 1 2 3
Pixels rejected : 123 171 89 54
Image counts : 68647 16567 10165 11588
Image cts rejected: 65036 13265 7983 10169
Image cts rej (%) : 94.74 80.07 78.53 87.75
filtering data...
Total counts : 68647 16567 10165 11588
Total cts rejected: 65036 13265 7983 10169
Total cts rej (%) : 94.74 80.07 78.53 87.75
Number of clean counts accepted : 10514
writing history cards...
copying extensions...
writing out hot pixs...
Number of rejected pixels : 437
updating NEVENTS keywords...
closing data file...
closing clean file...
Command not found; type ? for a command listing
!screen:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!screen:ASCA > set datadir .
Setting data directory to /data/data17/seq_proc/50006000.007/
Setting mkf directory to /data/data17/seq_proc/50006000.007/
!screen:ASCA > read events ad50006000s000112h.unf
Got new instrument: SIS0
Setting: IMAGE binning = 4
WMAP binning = 8
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 4095
Got the minimum time resolution of the read data: 16.000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data17/seq_proc/50006000.007/
HK Directory is: /data/data17/seq_proc/50006000.007/
!screen:ASCA-SIS0-BRIGHT2 > select event "grade==0||grade==2||grade==3||grade==4" save_file=no
!screen:ASCA-SIS0-BRIGHT2 > select mkf "@criteria.tmp" data_dir=. ASCA_mkf_def_expr=ft*.mkf
!screen:ASCA-SIS0-BRIGHT2 > extract events
!screen:ASCA-SIS0-BRIGHT2 > sisclean saoimage=no sis_plot=no clean=2 cellsize=5 log_prob=-5.24 bkg_thr=3 clean_phalow=0 clean_phahi=4095
!screen:ASCA-SIS0-BRIGHT2 > save clean outfile=ad50006000s000112h.evt use_events=no
Wrote cleaned events file to ad50006000s000112h.evt
!screen:ASCA-SIS0-BRIGHT2 > exit save_session=no
-> Filtering ad50006000s000202m.unf into ad50006000s000202m.evtThe sum of the selected column is 2626.3414 The mean of the selected column is 70.982199 The standard deviation of the selected column is 89.184194 The minimum of selected column is 1.8125099 The maximum of selected column is 376.21991 The number of points used in calculation is 37-> Standard Output From FTOOL fstatistic:
The sum of the selected column is 2467.6694 The mean of the selected column is 66.693767 The standard deviation of the selected column is 86.252130 The minimum of selected column is 1.2556887 The maximum of selected column is 372.25116 The number of points used in calculation is 37-> Standard Output From FTOOL fstatistic:
The sum of the selected column is 3323.4478 The mean of the selected column is 89.822914 The standard deviation of the selected column is 123.17076 The minimum of selected column is 6.7812705 The maximum of selected column is 512.87659 The number of points used in calculation is 37-> Standard Output From FTOOL fstatistic:
The sum of the selected column is 2904.0289 The mean of the selected column is 78.487268 The standard deviation of the selected column is 99.354246 The minimum of selected column is 3.4886553 The maximum of selected column is 402.22000 The number of points used in calculation is 37-> Using the following selection criteria:
(SAA==0) &&(BR_EARTH>20) &&(ELV>10) &&(COR>6) &&(ACS==0) &&(ANG_DIST>0)&& (ANG_DIST<0.01) &&(FOV==0) && ( (S0_PIXL0>0.0 && S0_PIXL0<338.5 )&& (S0_PIXL1>0.0 && S0_PIXL1<325.4 )&& (S0_PIXL2>0.0 && S0_PIXL2<459.3 )&& (S0_PIXL3>0.0 && S0_PIXL3<376.5 ) ) &&( (S0_SATF0<1) ||(S0_SATF0>1)) &&( (S0_SATF1<1) ||(S0_SATF1>1)) &&( (S0_SATF2<1) ||(S0_SATF2>1)) &&( (S0_SATF3<1) ||(S0_SATF3>1)) &&((T_DY_NT<0)||(T_DY_NT>64)) &&((T_SAA <0)||(T_SAA >64))-> Standard Output From FTOOL xselect:
** XSELECT V1.3 **
!> Enter session name >[xsel] screen
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS S0CCDPOW
1 W50 EAST BRIGHT MEDIUM 27/04/93 23:50:32 0.32E+05 168750 1111
Processing file: /data/data17/seq_proc/50006000.007/ad50006000s000202m.unf
EXTRACTOR vers 2.0 11 Apr 1997.
Doing file: /data/data17/seq_proc/50006000.007/screen_work1001.xsl
Total Good Bad: Region Time Phase Cut
163337 76734 0 86603 0 0
Writing events file
76734 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
163337 76734 0 86603 0 0
in 11070.42 seconds
CLEANSIS_V1.6
allocating image arrays...
PROGRAM TO MAKE AN SIS SCIENCE FILE CLEANED OF ANOMALOUS PIXELS.
* Anomalous pixels may consist of at least two populations.
1. Persistent HOT pixels are removed by comparing to the chip mean.
2. Flickering WARM pixels are removed by comparing to the cell mean.
3. In faint areas (zero bgd), flickering pixels are removed with a
cutoff threshold.
Hints:
Choose cell size and thresholds based on the expected background and the PSF.
Use the DIRTYSIS option to examine the anomalous pixel spectra.
Try a multiple pass clean:
Choose a PHA cut to optimize the S/N of the flickering pixels,
then a broad band clean.
Be suspicious of extended source cleans.
For very bright sources you may need to turn off the iteration option.
See the help page for further info (fhelp cleansis)
Poisson clean cell size : 5
Poisson probability threshold : 0.631E-05
Zero Bgd Cutoff threshold (>) : 3
Iterate : T
Dirtysis : F
Minimum PHA value (inclusive) : 0
Maximum PHA value (inclusive) : 4095
open output file: /data/data17/seq_proc/50006000.007/screen_in_event.xsl
reading data file: /data/data17/seq_proc/50006000.007/screen_out_event.xsl
copying primary header to output file...
making chip image...
Total counts in chip images : 76734
copy bad pix array...
cleaning chip # 0
Hot pixels & counts : 78 45561
Flickering pixels iter, pixels & cnts : 1 40 1408
cleaning chip # 1
Hot pixels & counts : 22 8421
Flickering pixels iter, pixels & cnts : 1 117 837
cleaning chip # 2
Hot pixels & counts : 23 5205
Flickering pixels iter, pixels & cnts : 1 60 529
cleaning chip # 3
Hot pixels & counts : 29 7244
Flickering pixels iter, pixels & cnts : 1 18 207
Number of pixels rejected : 387
Number of (internal) image counts : 76734
Number of image cts rejected (N, %) : 69412 90.4579468
By chip : 0 1 2 3
Pixels rejected : 118 139 83 47
Image counts : 49500 11495 7277 8462
Image cts rejected: 46969 9258 5734 7451
Image cts rej (%) : 94.89 80.54 78.80 88.05
filtering data...
Total counts : 49500 11495 7277 8462
Total cts rejected: 46969 9258 5734 7451
Total cts rej (%) : 94.89 80.54 78.80 88.05
Number of clean counts accepted : 7322
writing history cards...
copying extensions...
writing out hot pixs...
Number of rejected pixels : 387
updating NEVENTS keywords...
closing data file...
closing clean file...
Command not found; type ? for a command listing
!screen:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!screen:ASCA > set datadir .
Setting data directory to /data/data17/seq_proc/50006000.007/
Setting mkf directory to /data/data17/seq_proc/50006000.007/
!screen:ASCA > read events ad50006000s000202m.unf
Got new instrument: SIS0
Setting: IMAGE binning = 4
WMAP binning = 8
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 2047
Got the minimum time resolution of the read data: 16.000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data17/seq_proc/50006000.007/
HK Directory is: /data/data17/seq_proc/50006000.007/
!screen:ASCA-SIS0-BRIGHT > select event "grade==0||grade==2||grade==3||grade==4" save_file=no
!screen:ASCA-SIS0-BRIGHT > select mkf "@criteria.tmp" data_dir=. ASCA_mkf_def_expr=ft*.mkf
!screen:ASCA-SIS0-BRIGHT > extract events
!screen:ASCA-SIS0-BRIGHT > sisclean saoimage=no sis_plot=no clean=2 cellsize=5 log_prob=-5.24 bkg_thr=3 clean_phalow=0 clean_phahi=4095
!screen:ASCA-SIS0-BRIGHT > save clean outfile=ad50006000s000202m.evt use_events=no
Wrote cleaned events file to ad50006000s000202m.evt
!screen:ASCA-SIS0-BRIGHT > exit save_session=no
-> Skipping ad50006000s000301h.unf because of modeThe sum of the selected column is 1514.1148 The mean of the selected column is 24.033569 The standard deviation of the selected column is 9.8228261 The minimum of selected column is 0.51658332 The maximum of selected column is 58.812672 The number of points used in calculation is 63-> Standard Output From FTOOL fstatistic:
The sum of the selected column is 1504.2857 The mean of the selected column is 23.877551 The standard deviation of the selected column is 12.447555 The minimum of selected column is 9.2500267 The maximum of selected column is 87.250252 The number of points used in calculation is 63-> Standard Output From FTOOL fstatistic:
The sum of the selected column is 1429.1019 The mean of the selected column is 22.684157 The standard deviation of the selected column is 10.541140 The minimum of selected column is 1.0247430 The maximum of selected column is 50.562653 The number of points used in calculation is 63-> Using the following selection criteria:
(SAA==0) &&(BR_EARTH>20) &&(ELV>10) &&(COR>6) &&(ACS==0) &&(ANG_DIST>0)&& (ANG_DIST<0.01) &&(FOV==0) && ( (S0_PIXL0>0.0 && S0_PIXL0<53.5 )&& (S0_PIXL2>0.0 && S0_PIXL2<61.2 )&& (S0_PIXL3>0.0 && S0_PIXL3<54.3 ) ) &&( (S0_SATF0<1) ||(S0_SATF0>1)) &&( (S0_SATF2<1) ||(S0_SATF2>1)) &&( (S0_SATF2<1) ||(S0_SATF2>1)) &&( (S0_SATF3<1) ||(S0_SATF3>1)) &&((T_DY_NT<0)||(T_DY_NT>32)) &&((T_SAA <0)||(T_SAA >32))-> Standard Output From FTOOL xselect:
** XSELECT V1.3 **
!> Enter session name >[xsel] screen
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS S0CCDPOW
1 W50 EAST BRIGHT HIGH 28/04/93 14:34:00 0.21E+04 14123 1011
Processing file: /data/data17/seq_proc/50006000.007/ad50006000s000302h.unf
EXTRACTOR vers 2.0 11 Apr 1997.
Doing file: /data/data17/seq_proc/50006000.007/screen_work1001.xsl
Total Good Bad: Region Time Phase Cut
13951 12767 0 1184 0 0
Writing events file
12767 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
13951 12767 0 1184 0 0
in 1939.59 seconds
CLEANSIS_V1.6
allocating image arrays...
PROGRAM TO MAKE AN SIS SCIENCE FILE CLEANED OF ANOMALOUS PIXELS.
* Anomalous pixels may consist of at least two populations.
1. Persistent HOT pixels are removed by comparing to the chip mean.
2. Flickering WARM pixels are removed by comparing to the cell mean.
3. In faint areas (zero bgd), flickering pixels are removed with a
cutoff threshold.
Hints:
Choose cell size and thresholds based on the expected background and the PSF.
Use the DIRTYSIS option to examine the anomalous pixel spectra.
Try a multiple pass clean:
Choose a PHA cut to optimize the S/N of the flickering pixels,
then a broad band clean.
Be suspicious of extended source cleans.
For very bright sources you may need to turn off the iteration option.
See the help page for further info (fhelp cleansis)
Poisson clean cell size : 5
Poisson probability threshold : 0.631E-05
Zero Bgd Cutoff threshold (>) : 3
Iterate : T
Dirtysis : F
Minimum PHA value (inclusive) : 0
Maximum PHA value (inclusive) : 4095
open output file: /data/data17/seq_proc/50006000.007/screen_in_event.xsl
reading data file: /data/data17/seq_proc/50006000.007/screen_out_event.xsl
copying primary header to output file...
making chip image...
Total counts in chip images : 12767
copy bad pix array...
cleaning chip # 0
Hot pixels & counts : 71 7560
Flickering pixels iter, pixels & cnts : 1 27 405
cleaning chip # 1
Hot pixels & counts : 20 1489
Flickering pixels iter, pixels & cnts : 1 13 69
cleaning chip # 2
Hot pixels & counts : 15 697
Flickering pixels iter, pixels & cnts : 1 9 55
cleaning chip # 3
Hot pixels & counts : 19 1067
Flickering pixels iter, pixels & cnts : 1 13 84
Number of pixels rejected : 187
Number of (internal) image counts : 12767
Number of image cts rejected (N, %) : 11426 89.4963608
By chip : 0 1 2 3
Pixels rejected : 98 33 24 32
Image counts : 8442 1930 1051 1344
Image cts rejected: 7965 1558 752 1151
Image cts rej (%) : 94.35 80.73 71.55 85.64
filtering data...
Total counts : 8442 1930 1051 1344
Total cts rejected: 7965 1558 752 1151
Total cts rej (%) : 94.35 80.73 71.55 85.64
Number of clean counts accepted : 1341
writing history cards...
copying extensions...
writing out hot pixs...
Number of rejected pixels : 187
updating NEVENTS keywords...
closing data file...
closing clean file...
Command not found; type ? for a command listing
!screen:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!screen:ASCA > set datadir .
Setting data directory to /data/data17/seq_proc/50006000.007/
Setting mkf directory to /data/data17/seq_proc/50006000.007/
!screen:ASCA > read events ad50006000s000302h.unf
Got new instrument: SIS0
Setting: IMAGE binning = 4
WMAP binning = 8
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 2047
Got the minimum time resolution of the read data: 16.000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data17/seq_proc/50006000.007/
HK Directory is: /data/data17/seq_proc/50006000.007/
!screen:ASCA-SIS0-BRIGHT > select event "grade==0||grade==2||grade==3||grade==4" save_file=no
!screen:ASCA-SIS0-BRIGHT > select mkf "@criteria.tmp" data_dir=. ASCA_mkf_def_expr=ft*.mkf
!screen:ASCA-SIS0-BRIGHT > extract events
!screen:ASCA-SIS0-BRIGHT > sisclean saoimage=no sis_plot=no clean=2 cellsize=5 log_prob=-5.24 bkg_thr=3 clean_phalow=0 clean_phahi=4095
!screen:ASCA-SIS0-BRIGHT > save clean outfile=ad50006000s000302h.evt use_events=no
Wrote cleaned events file to ad50006000s000302h.evt
!screen:ASCA-SIS0-BRIGHT > exit save_session=no
-> Filtering ad50006000s000312h.unf into ad50006000s000312h.evtThe sum of the selected column is 1514.1148 The mean of the selected column is 24.033569 The standard deviation of the selected column is 9.8228261 The minimum of selected column is 0.51658332 The maximum of selected column is 58.812672 The number of points used in calculation is 63-> Standard Output From FTOOL fstatistic:
The sum of the selected column is 1504.2857 The mean of the selected column is 23.877551 The standard deviation of the selected column is 12.447555 The minimum of selected column is 9.2500267 The maximum of selected column is 87.250252 The number of points used in calculation is 63-> Standard Output From FTOOL fstatistic:
The sum of the selected column is 1429.1019 The mean of the selected column is 22.684157 The standard deviation of the selected column is 10.541140 The minimum of selected column is 1.0247430 The maximum of selected column is 50.562653 The number of points used in calculation is 63-> Using the following selection criteria:
(SAA==0) &&(BR_EARTH>20) &&(ELV>10) &&(COR>6) &&(ACS==0) &&(ANG_DIST>0)&& (ANG_DIST<0.01) &&(FOV==0) && ( (S0_PIXL0>0.0 && S0_PIXL0<53.5 )&& (S0_PIXL2>0.0 && S0_PIXL2<61.2 )&& (S0_PIXL3>0.0 && S0_PIXL3<54.3 ) ) &&( (S0_SATF0<1) ||(S0_SATF0>1)) &&( (S0_SATF2<1) ||(S0_SATF2>1)) &&( (S0_SATF2<1) ||(S0_SATF2>1)) &&( (S0_SATF3<1) ||(S0_SATF3>1)) &&((T_DY_NT<0)||(T_DY_NT>32)) &&((T_SAA <0)||(T_SAA >32))-> Standard Output From FTOOL xselect:
** XSELECT V1.3 **
!> Enter session name >[xsel] screen
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS S0CCDPOW
1 W50 EAST BRIGHT2 HIGH 28/04/93 14:34:00 0.21E+04 14737 1011
Processing file: /data/data17/seq_proc/50006000.007/ad50006000s000312h.unf
EXTRACTOR vers 2.0 11 Apr 1997.
Doing file: /data/data17/seq_proc/50006000.007/screen_work1001.xsl
Total Good Bad: Region Time Phase Cut
13983 12797 0 1186 0 0
Writing events file
12797 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
13983 12797 0 1186 0 0
in 1939.59 seconds
CLEANSIS_V1.6
allocating image arrays...
PROGRAM TO MAKE AN SIS SCIENCE FILE CLEANED OF ANOMALOUS PIXELS.
* Anomalous pixels may consist of at least two populations.
1. Persistent HOT pixels are removed by comparing to the chip mean.
2. Flickering WARM pixels are removed by comparing to the cell mean.
3. In faint areas (zero bgd), flickering pixels are removed with a
cutoff threshold.
Hints:
Choose cell size and thresholds based on the expected background and the PSF.
Use the DIRTYSIS option to examine the anomalous pixel spectra.
Try a multiple pass clean:
Choose a PHA cut to optimize the S/N of the flickering pixels,
then a broad band clean.
Be suspicious of extended source cleans.
For very bright sources you may need to turn off the iteration option.
See the help page for further info (fhelp cleansis)
Poisson clean cell size : 5
Poisson probability threshold : 0.631E-05
Zero Bgd Cutoff threshold (>) : 3
Iterate : T
Dirtysis : F
Minimum PHA value (inclusive) : 0
Maximum PHA value (inclusive) : 4095
open output file: /data/data17/seq_proc/50006000.007/screen_in_event.xsl
reading data file: /data/data17/seq_proc/50006000.007/screen_out_event.xsl
copying primary header to output file...
making chip image...
Total counts in chip images : 12797
copy bad pix array...
cleaning chip # 0
Hot pixels & counts : 71 7561
Flickering pixels iter, pixels & cnts : 1 27 405
cleaning chip # 1
Hot pixels & counts : 20 1489
Flickering pixels iter, pixels & cnts : 1 13 69
cleaning chip # 2
Hot pixels & counts : 15 697
Flickering pixels iter, pixels & cnts : 1 9 55
cleaning chip # 3
Hot pixels & counts : 19 1067
Flickering pixels iter, pixels & cnts : 1 13 84
Number of pixels rejected : 187
Number of (internal) image counts : 12797
Number of image cts rejected (N, %) : 11427 89.2943649
By chip : 0 1 2 3
Pixels rejected : 98 33 24 32
Image counts : 8455 1936 1057 1349
Image cts rejected: 7966 1558 752 1151
Image cts rej (%) : 94.22 80.48 71.14 85.32
filtering data...
Total counts : 8455 1936 1057 1349
Total cts rejected: 7966 1558 752 1151
Total cts rej (%) : 94.22 80.48 71.14 85.32
Number of clean counts accepted : 1370
writing history cards...
copying extensions...
writing out hot pixs...
Number of rejected pixels : 187
updating NEVENTS keywords...
closing data file...
closing clean file...
Command not found; type ? for a command listing
!screen:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!screen:ASCA > set datadir .
Setting data directory to /data/data17/seq_proc/50006000.007/
Setting mkf directory to /data/data17/seq_proc/50006000.007/
!screen:ASCA > read events ad50006000s000312h.unf
Got new instrument: SIS0
Setting: IMAGE binning = 4
WMAP binning = 8
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 4095
Got the minimum time resolution of the read data: 16.000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data17/seq_proc/50006000.007/
HK Directory is: /data/data17/seq_proc/50006000.007/
!screen:ASCA-SIS0-BRIGHT2 > select event "grade==0||grade==2||grade==3||grade==4" save_file=no
!screen:ASCA-SIS0-BRIGHT2 > select mkf "@criteria.tmp" data_dir=. ASCA_mkf_def_expr=ft*.mkf
!screen:ASCA-SIS0-BRIGHT2 > extract events
!screen:ASCA-SIS0-BRIGHT2 > sisclean saoimage=no sis_plot=no clean=2 cellsize=5 log_prob=-5.24 bkg_thr=3 clean_phalow=0 clean_phahi=4095
!screen:ASCA-SIS0-BRIGHT2 > save clean outfile=ad50006000s000312h.evt use_events=no
Wrote cleaned events file to ad50006000s000312h.evt
!screen:ASCA-SIS0-BRIGHT2 > exit save_session=no
-> Filtering ad50006000s000402l.unf into ad50006000s000402l.evt(SAA==0) &&(BR_EARTH>20) &&(ELV>10) &&(COR>6) &&(ACS==0) &&(ANG_DIST>0)&& (ANG_DIST<0.01) &&(FOV==0) && ( (S0_PIXL0>0)&& (S0_PIXL1>0)&& (S0_PIXL2>0)&& (S0_PIXL3>0) ) &&( (S0_SATF0<1) ||(S0_SATF0>1)) &&( (S0_SATF1<1) ||(S0_SATF1>1)) &&( (S0_SATF2<1) ||(S0_SATF2>1)) &&( (S0_SATF3<1) ||(S0_SATF3>1)) &&((T_DY_NT<0)||(T_DY_NT>64)) &&((T_SAA <0)||(T_SAA >64))-> Standard Output From FTOOL xselect:
** XSELECT V1.3 **
!> Enter session name >[xsel] screen
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS S0CCDPOW
1 W50 EAST BRIGHT LOW 28/04/93 01:05:12 0.18E+04 2859 1111
Processing file: /data/data17/seq_proc/50006000.007/ad50006000s000402l.unf
EXTRACTOR vers 2.0 11 Apr 1997.
Skipping file: /data/data17/seq_proc/50006000.007/screen_work1001.xsl
Writing events file
0 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
0 0 0 0 0 0
in 0.00 seconds
CLEANSIS_V1.6
allocating image arrays...
PROGRAM TO MAKE AN SIS SCIENCE FILE CLEANED OF ANOMALOUS PIXELS.
* Anomalous pixels may consist of at least two populations.
1. Persistent HOT pixels are removed by comparing to the chip mean.
2. Flickering WARM pixels are removed by comparing to the cell mean.
3. In faint areas (zero bgd), flickering pixels are removed with a
cutoff threshold.
Hints:
Choose cell size and thresholds based on the expected background and the PSF.
Use the DIRTYSIS option to examine the anomalous pixel spectra.
Try a multiple pass clean:
Choose a PHA cut to optimize the S/N of the flickering pixels,
then a broad band clean.
Be suspicious of extended source cleans.
For very bright sources you may need to turn off the iteration option.
See the help page for further info (fhelp cleansis)
Poisson clean cell size : 5
Poisson probability threshold : 0.631E-05
Zero Bgd Cutoff threshold (>) : 3
Iterate : T
Dirtysis : F
Minimum PHA value (inclusive) : 0
Maximum PHA value (inclusive) : 4095
open output file: /data/data17/seq_proc/50006000.007/screen_in_event.xsl
reading data file: /data/data17/seq_proc/50006000.007/screen_out_event.xsl
copying primary header to output file...
making chip image...
Total counts in chip images : 0
copy bad pix array...
cleaning chip # 0
cleaning chip # 1
cleaning chip # 2
cleaning chip # 3
Number of pixels rejected : 0
Number of (internal) image counts : 0
Number of image cts rejected (N, %) : 0 0.0000000
By chip : 0 1 2 3
Pixels rejected : 0 0 0 0
Image counts : 0 0 0 0
Image cts rejected: 0 0 0 0
Image cts rej (%) : 0.00 0.00 0.00 0.00
filtering data...
Total counts : 0 0 0 0
Total cts rejected: 0 0 0 0
Total cts rej (%) : 0.00 0.00 0.00 0.00
Number of clean counts accepted : 0
writing history cards...
copying extensions...
writing out hot pixs...
Number of rejected pixels : 0
updating NEVENTS keywords...
closing data file...
closing clean file...
Command not found; type ? for a command listing
!screen:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!screen:ASCA > set datadir .
Setting data directory to /data/data17/seq_proc/50006000.007/
Setting mkf directory to /data/data17/seq_proc/50006000.007/
!screen:ASCA > read events ad50006000s000402l.unf
Got new instrument: SIS0
Setting: IMAGE binning = 4
WMAP binning = 8
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 2047
Got the minimum time resolution of the read data: 16.000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data17/seq_proc/50006000.007/
HK Directory is: /data/data17/seq_proc/50006000.007/
!screen:ASCA-SIS0-BRIGHT > select event "grade==0||grade==2||grade==3||grade==4" save_file=no
!screen:ASCA-SIS0-BRIGHT > select mkf "@criteria.tmp" data_dir=. ASCA_mkf_def_expr=ft*.mkf
!screen:ASCA-SIS0-BRIGHT > extract events
!screen:ASCA-SIS0-BRIGHT > sisclean saoimage=no sis_plot=no clean=2 cellsize=5 log_prob=-5.24 bkg_thr=3 clean_phalow=0 clean_phahi=4095
!screen:ASCA-SIS0-BRIGHT > save clean outfile=ad50006000s000402l.evt use_events=no
Wrote cleaned events file to ad50006000s000402l.evt
!screen:ASCA-SIS0-BRIGHT > exit save_session=no
-> Deleting ad50006000s000402l.evt since it contains 0 eventsThe sum of the selected column is 3093.1030 The mean of the selected column is 21.185637 The standard deviation of the selected column is 7.7482789 The minimum of selected column is 8.1562738 The maximum of selected column is 58.468922 The number of points used in calculation is 146-> Standard Output From FTOOL fstatistic:
The sum of the selected column is 2405.9863 The mean of the selected column is 16.479358 The standard deviation of the selected column is 6.0688783 The minimum of selected column is 4.7812643 The maximum of selected column is 40.562618 The number of points used in calculation is 146-> Standard Output From FTOOL fstatistic:
The sum of the selected column is 3350.5412 The mean of the selected column is 22.948913 The standard deviation of the selected column is 13.369122 The minimum of selected column is 6.1250181 The maximum of selected column is 97.187798 The number of points used in calculation is 146-> Standard Output From FTOOL fstatistic:
The sum of the selected column is 2696.9768 The mean of the selected column is 18.472444 The standard deviation of the selected column is 7.4531989 The minimum of selected column is 3.7500110 The maximum of selected column is 41.218872 The number of points used in calculation is 146-> Using the following selection criteria:
(SAA==0) &&(BR_EARTH>20) &&(ELV>10) &&(COR>6) &&(ACS==0) &&(ANG_DIST>0)&& (ANG_DIST<0.01) &&(FOV==0) && ( (S0_PIXL0>0.0 && S0_PIXL0<44.4 )&& (S0_PIXL1>0.0 && S0_PIXL1<34.6 )&& (S0_PIXL2>0.0 && S0_PIXL2<63 )&& (S0_PIXL3>0.0 && S0_PIXL3<40.8 ) ) &&( (S0_SATF0<1) ||(S0_SATF0>1)) &&( (S0_SATF1<1) ||(S0_SATF1>1)) &&( (S0_SATF2<1) ||(S0_SATF2>1)) &&( (S0_SATF3<1) ||(S0_SATF3>1)) &&((T_DY_NT<0)||(T_DY_NT>64)) &&((T_SAA <0)||(T_SAA >64))-> Standard Output From FTOOL xselect:
** XSELECT V1.3 **
!> Enter session name >[xsel] screen
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS S0CCDPOW
1 W50 EAST BRIGHT MEDIUM 28/04/93 19:50:16 0.12E+05 61343 1111
Processing file: /data/data17/seq_proc/50006000.007/ad50006000s000502m.unf
EXTRACTOR vers 2.0 11 Apr 1997.
Doing file: /data/data17/seq_proc/50006000.007/screen_work1001.xsl
Total Good Bad: Region Time Phase Cut
59005 38053 0 20952 0 0
Writing events file
38053 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
59005 38053 0 20952 0 0
in 5512.04 seconds
CLEANSIS_V1.6
allocating image arrays...
PROGRAM TO MAKE AN SIS SCIENCE FILE CLEANED OF ANOMALOUS PIXELS.
* Anomalous pixels may consist of at least two populations.
1. Persistent HOT pixels are removed by comparing to the chip mean.
2. Flickering WARM pixels are removed by comparing to the cell mean.
3. In faint areas (zero bgd), flickering pixels are removed with a
cutoff threshold.
Hints:
Choose cell size and thresholds based on the expected background and the PSF.
Use the DIRTYSIS option to examine the anomalous pixel spectra.
Try a multiple pass clean:
Choose a PHA cut to optimize the S/N of the flickering pixels,
then a broad band clean.
Be suspicious of extended source cleans.
For very bright sources you may need to turn off the iteration option.
See the help page for further info (fhelp cleansis)
Poisson clean cell size : 5
Poisson probability threshold : 0.631E-05
Zero Bgd Cutoff threshold (>) : 3
Iterate : T
Dirtysis : F
Minimum PHA value (inclusive) : 0
Maximum PHA value (inclusive) : 4095
open output file: /data/data17/seq_proc/50006000.007/screen_in_event.xsl
reading data file: /data/data17/seq_proc/50006000.007/screen_out_event.xsl
copying primary header to output file...
making chip image...
Total counts in chip images : 38053
copy bad pix array...
cleaning chip # 0
Hot pixels & counts : 78 22297
Flickering pixels iter, pixels & cnts : 1 29 661
cleaning chip # 1
Hot pixels & counts : 24 4443
Flickering pixels iter, pixels & cnts : 1 27 227
cleaning chip # 2
Hot pixels & counts : 25 3032
Flickering pixels iter, pixels & cnts : 1 39 298
cleaning chip # 3
Hot pixels & counts : 25 3279
Flickering pixels iter, pixels & cnts : 1 19 153
Number of pixels rejected : 266
Number of (internal) image counts : 38053
Number of image cts rejected (N, %) : 34390 90.3739548
By chip : 0 1 2 3
Pixels rejected : 107 51 64 44
Image counts : 24210 5817 4108 3918
Image cts rejected: 22958 4670 3330 3432
Image cts rej (%) : 94.83 80.28 81.06 87.60
filtering data...
Total counts : 24210 5817 4108 3918
Total cts rejected: 22958 4670 3330 3432
Total cts rej (%) : 94.83 80.28 81.06 87.60
Number of clean counts accepted : 3663
writing history cards...
copying extensions...
writing out hot pixs...
Number of rejected pixels : 266
updating NEVENTS keywords...
closing data file...
closing clean file...
Command not found; type ? for a command listing
!screen:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!screen:ASCA > set datadir .
Setting data directory to /data/data17/seq_proc/50006000.007/
Setting mkf directory to /data/data17/seq_proc/50006000.007/
!screen:ASCA > read events ad50006000s000502m.unf
Got new instrument: SIS0
Setting: IMAGE binning = 4
WMAP binning = 8
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 2047
Got the minimum time resolution of the read data: 16.000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data17/seq_proc/50006000.007/
HK Directory is: /data/data17/seq_proc/50006000.007/
!screen:ASCA-SIS0-BRIGHT > select event "grade==0||grade==2||grade==3||grade==4" save_file=no
!screen:ASCA-SIS0-BRIGHT > select mkf "@criteria.tmp" data_dir=. ASCA_mkf_def_expr=ft*.mkf
!screen:ASCA-SIS0-BRIGHT > extract events
!screen:ASCA-SIS0-BRIGHT > sisclean saoimage=no sis_plot=no clean=2 cellsize=5 log_prob=-5.24 bkg_thr=3 clean_phalow=0 clean_phahi=4095
!screen:ASCA-SIS0-BRIGHT > save clean outfile=ad50006000s000502m.evt use_events=no
Wrote cleaned events file to ad50006000s000502m.evt
!screen:ASCA-SIS0-BRIGHT > exit save_session=no
-> Skipping ad50006000s000601h.unf because of modeThe sum of the selected column is 943.75284 The mean of the selected column is 20.516366 The standard deviation of the selected column is 6.1809589 The minimum of selected column is 10.843783 The maximum of selected column is 34.906353 The number of points used in calculation is 46-> Standard Output From FTOOL fstatistic:
The sum of the selected column is 589.68928 The mean of the selected column is 12.819332 The standard deviation of the selected column is 5.4039473 The minimum of selected column is 5.3750162 The maximum of selected column is 33.093849 The number of points used in calculation is 46-> Standard Output From FTOOL fstatistic:
The sum of the selected column is 808.34619 The mean of the selected column is 17.572743 The standard deviation of the selected column is 6.8581917 The minimum of selected column is 6.2187691 The maximum of selected column is 35.562607 The number of points used in calculation is 46-> Standard Output From FTOOL fstatistic:
The sum of the selected column is 826.84625 The mean of the selected column is 17.974918 The standard deviation of the selected column is 6.3612640 The minimum of selected column is 6.0625186 The maximum of selected column is 36.687611 The number of points used in calculation is 46-> Using the following selection criteria:
(SAA==0) &&(BR_EARTH>20) &&(ELV>10) &&(COR>6) &&(ACS==0) &&(ANG_DIST>0)&& (ANG_DIST<0.01) &&(FOV==0) && ( (S0_PIXL0>1.9 && S0_PIXL0<39 )&& (S0_PIXL1>0.0 && S0_PIXL1<29 )&& (S0_PIXL2>0.0 && S0_PIXL2<38.1 )&& (S0_PIXL3>0.0 && S0_PIXL3<37 ) ) &&( (S0_SATF0<1) ||(S0_SATF0>1)) &&( (S0_SATF1<1) ||(S0_SATF1>1)) &&( (S0_SATF2<1) ||(S0_SATF2>1)) &&( (S0_SATF3<1) ||(S0_SATF3>1)) &&((T_DY_NT<0)||(T_DY_NT>64)) &&((T_SAA <0)||(T_SAA >64))-> Standard Output From FTOOL xselect:
** XSELECT V1.3 **
!> Enter session name >[xsel] screen
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS S0CCDPOW
1 W50 EAST BRIGHT HIGH 28/04/93 22:52:12 0.15E+04 10533 1111
Processing file: /data/data17/seq_proc/50006000.007/ad50006000s000602h.unf
EXTRACTOR vers 2.0 11 Apr 1997.
Doing file: /data/data17/seq_proc/50006000.007/screen_work1001.xsl
Total Good Bad: Region Time Phase Cut
10371 9660 0 711 0 0
Writing events file
9660 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
10371 9660 0 711 0 0
in 1453.93 seconds
CLEANSIS_V1.6
allocating image arrays...
PROGRAM TO MAKE AN SIS SCIENCE FILE CLEANED OF ANOMALOUS PIXELS.
* Anomalous pixels may consist of at least two populations.
1. Persistent HOT pixels are removed by comparing to the chip mean.
2. Flickering WARM pixels are removed by comparing to the cell mean.
3. In faint areas (zero bgd), flickering pixels are removed with a
cutoff threshold.
Hints:
Choose cell size and thresholds based on the expected background and the PSF.
Use the DIRTYSIS option to examine the anomalous pixel spectra.
Try a multiple pass clean:
Choose a PHA cut to optimize the S/N of the flickering pixels,
then a broad band clean.
Be suspicious of extended source cleans.
For very bright sources you may need to turn off the iteration option.
See the help page for further info (fhelp cleansis)
Poisson clean cell size : 5
Poisson probability threshold : 0.631E-05
Zero Bgd Cutoff threshold (>) : 3
Iterate : T
Dirtysis : F
Minimum PHA value (inclusive) : 0
Maximum PHA value (inclusive) : 4095
open output file: /data/data17/seq_proc/50006000.007/screen_in_event.xsl
reading data file: /data/data17/seq_proc/50006000.007/screen_out_event.xsl
copying primary header to output file...
making chip image...
Total counts in chip images : 9660
copy bad pix array...
cleaning chip # 0
Hot pixels & counts : 71 5624
Flickering pixels iter, pixels & cnts : 1 22 297
cleaning chip # 1
Hot pixels & counts : 18 1067
Flickering pixels iter, pixels & cnts : 1 12 66
cleaning chip # 2
Hot pixels & counts : 17 719
Flickering pixels iter, pixels & cnts : 1 13 55
cleaning chip # 3
Hot pixels & counts : 19 792
Flickering pixels iter, pixels & cnts : 1 12 64
Number of pixels rejected : 184
Number of (internal) image counts : 9660
Number of image cts rejected (N, %) : 8684 89.8964767
By chip : 0 1 2 3
Pixels rejected : 93 30 30 31
Image counts : 6264 1439 968 989
Image cts rejected: 5921 1133 774 856
Image cts rej (%) : 94.52 78.74 79.96 86.55
filtering data...
Total counts : 6264 1439 968 989
Total cts rejected: 5921 1133 774 856
Total cts rej (%) : 94.52 78.74 79.96 86.55
Number of clean counts accepted : 976
writing history cards...
copying extensions...
writing out hot pixs...
Number of rejected pixels : 184
updating NEVENTS keywords...
closing data file...
closing clean file...
Command not found; type ? for a command listing
!screen:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!screen:ASCA > set datadir .
Setting data directory to /data/data17/seq_proc/50006000.007/
Setting mkf directory to /data/data17/seq_proc/50006000.007/
!screen:ASCA > read events ad50006000s000602h.unf
Got new instrument: SIS0
Setting: IMAGE binning = 4
WMAP binning = 8
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 2047
Got the minimum time resolution of the read data: 16.000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data17/seq_proc/50006000.007/
HK Directory is: /data/data17/seq_proc/50006000.007/
!screen:ASCA-SIS0-BRIGHT > select event "grade==0||grade==2||grade==3||grade==4" save_file=no
!screen:ASCA-SIS0-BRIGHT > select mkf "@criteria.tmp" data_dir=. ASCA_mkf_def_expr=ft*.mkf
!screen:ASCA-SIS0-BRIGHT > extract events
!screen:ASCA-SIS0-BRIGHT > sisclean saoimage=no sis_plot=no clean=2 cellsize=5 log_prob=-5.24 bkg_thr=3 clean_phalow=0 clean_phahi=4095
!screen:ASCA-SIS0-BRIGHT > save clean outfile=ad50006000s000602h.evt use_events=no
Wrote cleaned events file to ad50006000s000602h.evt
!screen:ASCA-SIS0-BRIGHT > exit save_session=no
-> Filtering ad50006000s000612h.unf into ad50006000s000612h.evtThe sum of the selected column is 943.75284 The mean of the selected column is 20.516366 The standard deviation of the selected column is 6.1809589 The minimum of selected column is 10.843783 The maximum of selected column is 34.906353 The number of points used in calculation is 46-> Standard Output From FTOOL fstatistic:
The sum of the selected column is 589.68928 The mean of the selected column is 12.819332 The standard deviation of the selected column is 5.4039473 The minimum of selected column is 5.3750162 The maximum of selected column is 33.093849 The number of points used in calculation is 46-> Standard Output From FTOOL fstatistic:
The sum of the selected column is 808.34619 The mean of the selected column is 17.572743 The standard deviation of the selected column is 6.8581917 The minimum of selected column is 6.2187691 The maximum of selected column is 35.562607 The number of points used in calculation is 46-> Standard Output From FTOOL fstatistic:
The sum of the selected column is 826.84625 The mean of the selected column is 17.974918 The standard deviation of the selected column is 6.3612640 The minimum of selected column is 6.0625186 The maximum of selected column is 36.687611 The number of points used in calculation is 46-> Using the following selection criteria:
(SAA==0) &&(BR_EARTH>20) &&(ELV>10) &&(COR>6) &&(ACS==0) &&(ANG_DIST>0)&& (ANG_DIST<0.01) &&(FOV==0) && ( (S0_PIXL0>1.9 && S0_PIXL0<39 )&& (S0_PIXL1>0.0 && S0_PIXL1<29 )&& (S0_PIXL2>0.0 && S0_PIXL2<38.1 )&& (S0_PIXL3>0.0 && S0_PIXL3<37 ) ) &&( (S0_SATF0<1) ||(S0_SATF0>1)) &&( (S0_SATF1<1) ||(S0_SATF1>1)) &&( (S0_SATF2<1) ||(S0_SATF2>1)) &&( (S0_SATF3<1) ||(S0_SATF3>1)) &&((T_DY_NT<0)||(T_DY_NT>64)) &&((T_SAA <0)||(T_SAA >64))-> Standard Output From FTOOL xselect:
** XSELECT V1.3 **
!> Enter session name >[xsel] screen
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS S0CCDPOW
1 W50 EAST BRIGHT2 HIGH 28/04/93 22:52:12 0.15E+04 10938 1111
Processing file: /data/data17/seq_proc/50006000.007/ad50006000s000612h.unf
EXTRACTOR vers 2.0 11 Apr 1997.
Doing file: /data/data17/seq_proc/50006000.007/screen_work1001.xsl
Total Good Bad: Region Time Phase Cut
10404 9692 0 712 0 0
Writing events file
9692 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
10404 9692 0 712 0 0
in 1453.93 seconds
CLEANSIS_V1.6
allocating image arrays...
PROGRAM TO MAKE AN SIS SCIENCE FILE CLEANED OF ANOMALOUS PIXELS.
* Anomalous pixels may consist of at least two populations.
1. Persistent HOT pixels are removed by comparing to the chip mean.
2. Flickering WARM pixels are removed by comparing to the cell mean.
3. In faint areas (zero bgd), flickering pixels are removed with a
cutoff threshold.
Hints:
Choose cell size and thresholds based on the expected background and the PSF.
Use the DIRTYSIS option to examine the anomalous pixel spectra.
Try a multiple pass clean:
Choose a PHA cut to optimize the S/N of the flickering pixels,
then a broad band clean.
Be suspicious of extended source cleans.
For very bright sources you may need to turn off the iteration option.
See the help page for further info (fhelp cleansis)
Poisson clean cell size : 5
Poisson probability threshold : 0.631E-05
Zero Bgd Cutoff threshold (>) : 3
Iterate : T
Dirtysis : F
Minimum PHA value (inclusive) : 0
Maximum PHA value (inclusive) : 4095
open output file: /data/data17/seq_proc/50006000.007/screen_in_event.xsl
reading data file: /data/data17/seq_proc/50006000.007/screen_out_event.xsl
copying primary header to output file...
making chip image...
Total counts in chip images : 9692
copy bad pix array...
cleaning chip # 0
Hot pixels & counts : 71 5624
Flickering pixels iter, pixels & cnts : 1 22 298
cleaning chip # 1
Hot pixels & counts : 18 1067
Flickering pixels iter, pixels & cnts : 1 12 66
cleaning chip # 2
Hot pixels & counts : 17 719
Flickering pixels iter, pixels & cnts : 1 13 55
cleaning chip # 3
Hot pixels & counts : 19 792
Flickering pixels iter, pixels & cnts : 1 12 65
Number of pixels rejected : 184
Number of (internal) image counts : 9692
Number of image cts rejected (N, %) : 8686 89.6203079
By chip : 0 1 2 3
Pixels rejected : 93 30 30 31
Image counts : 6272 1449 974 997
Image cts rejected: 5922 1133 774 857
Image cts rej (%) : 94.42 78.19 79.47 85.96
filtering data...
Total counts : 6272 1449 974 997
Total cts rejected: 5922 1133 774 857
Total cts rej (%) : 94.42 78.19 79.47 85.96
Number of clean counts accepted : 1006
writing history cards...
copying extensions...
writing out hot pixs...
Number of rejected pixels : 184
updating NEVENTS keywords...
closing data file...
closing clean file...
Command not found; type ? for a command listing
!screen:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!screen:ASCA > set datadir .
Setting data directory to /data/data17/seq_proc/50006000.007/
Setting mkf directory to /data/data17/seq_proc/50006000.007/
!screen:ASCA > read events ad50006000s000612h.unf
Got new instrument: SIS0
Setting: IMAGE binning = 4
WMAP binning = 8
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 4095
Got the minimum time resolution of the read data: 16.000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data17/seq_proc/50006000.007/
HK Directory is: /data/data17/seq_proc/50006000.007/
!screen:ASCA-SIS0-BRIGHT2 > select event "grade==0||grade==2||grade==3||grade==4" save_file=no
!screen:ASCA-SIS0-BRIGHT2 > select mkf "@criteria.tmp" data_dir=. ASCA_mkf_def_expr=ft*.mkf
!screen:ASCA-SIS0-BRIGHT2 > extract events
!screen:ASCA-SIS0-BRIGHT2 > sisclean saoimage=no sis_plot=no clean=2 cellsize=5 log_prob=-5.24 bkg_thr=3 clean_phalow=0 clean_phahi=4095
!screen:ASCA-SIS0-BRIGHT2 > save clean outfile=ad50006000s000612h.evt use_events=no
Wrote cleaned events file to ad50006000s000612h.evt
!screen:ASCA-SIS0-BRIGHT2 > exit save_session=no
-> Skipping ad50006000s100101h.unf because of modeThe sum of the selected column is 14155.512 The mean of the selected column is 31.667813 The standard deviation of the selected column is 17.632306 The minimum of selected column is 1.9719452 The maximum of selected column is 195.56310 The number of points used in calculation is 447-> Standard Output From FTOOL fstatistic:
The sum of the selected column is 14346.812 The mean of the selected column is 32.167740 The standard deviation of the selected column is 17.032225 The minimum of selected column is 1.0127584 The maximum of selected column is 188.43808 The number of points used in calculation is 446-> Standard Output From FTOOL fstatistic:
The sum of the selected column is 13865.688 The mean of the selected column is 31.019435 The standard deviation of the selected column is 20.509319 The minimum of selected column is 7.7812734 The maximum of selected column is 315.93851 The number of points used in calculation is 447-> Standard Output From FTOOL fstatistic:
The sum of the selected column is 13996.932 The mean of the selected column is 31.383255 The standard deviation of the selected column is 16.501261 The minimum of selected column is 0.78906512 The maximum of selected column is 139.37543 The number of points used in calculation is 446-> Using the following selection criteria:
(SAA==0) &&(BR_EARTH>20) &&(ELV>10) &&(COR>6) &&(ACS==0) &&(ANG_DIST>0)&& (ANG_DIST<0.01) &&(FOV==0) && ( (S1_PIXL0>0.0 && S1_PIXL0<84.5 )&& (S1_PIXL1>0.0 && S1_PIXL1<83.2 )&& (S1_PIXL2>0.0 && S1_PIXL2<92.5 )&& (S1_PIXL3>0.0 && S1_PIXL3<80.8 ) ) &&( (S1_SATF0<1) ||(S1_SATF0>1)) &&( (S1_SATF1<1) ||(S1_SATF1>1)) &&( (S1_SATF2<1) ||(S1_SATF2>1)) &&( (S1_SATF3<1) ||(S1_SATF3>1)) &&((T_DY_NT<0)||(T_DY_NT>64)) &&((T_SAA <0)||(T_SAA >64))-> Standard Output From FTOOL xselect:
** XSELECT V1.3 **
!> Enter session name >[xsel] screen
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS S1CCDPOW
1 W50 EAST BRIGHT HIGH 28/04/93 03:44:28 0.24E+05 179196 1111
Processing file: /data/data17/seq_proc/50006000.007/ad50006000s100102h.unf
EXTRACTOR vers 2.0 11 Apr 1997.
Doing file: /data/data17/seq_proc/50006000.007/screen_work1001.xsl
Total Good Bad: Region Time Phase Cut
172384 124157 0 48227 0 0
Writing events file
124157 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
172384 124157 0 48227 0 0
in 17516.77 seconds
CLEANSIS_V1.6
allocating image arrays...
PROGRAM TO MAKE AN SIS SCIENCE FILE CLEANED OF ANOMALOUS PIXELS.
* Anomalous pixels may consist of at least two populations.
1. Persistent HOT pixels are removed by comparing to the chip mean.
2. Flickering WARM pixels are removed by comparing to the cell mean.
3. In faint areas (zero bgd), flickering pixels are removed with a
cutoff threshold.
Hints:
Choose cell size and thresholds based on the expected background and the PSF.
Use the DIRTYSIS option to examine the anomalous pixel spectra.
Try a multiple pass clean:
Choose a PHA cut to optimize the S/N of the flickering pixels,
then a broad band clean.
Be suspicious of extended source cleans.
For very bright sources you may need to turn off the iteration option.
See the help page for further info (fhelp cleansis)
Poisson clean cell size : 5
Poisson probability threshold : 0.631E-05
Zero Bgd Cutoff threshold (>) : 3
Iterate : T
Dirtysis : F
Minimum PHA value (inclusive) : 0
Maximum PHA value (inclusive) : 4095
open output file: /data/data17/seq_proc/50006000.007/screen_in_event.xsl
reading data file: /data/data17/seq_proc/50006000.007/screen_out_event.xsl
copying primary header to output file...
making chip image...
Total counts in chip images : 124157
copy bad pix array...
cleaning chip # 0
Hot pixels & counts : 50 26090
Flickering pixels iter, pixels & cnts : 1 58 1267
cleaning chip # 1
Hot pixels & counts : 43 30787
Flickering pixels iter, pixels & cnts : 1 141 1824
cleaning chip # 2
Hot pixels & counts : 38 24585
Flickering pixels iter, pixels & cnts : 1 41 802
cleaning chip # 3
Hot pixels & counts : 40 25329
Flickering pixels iter, pixels & cnts : 1 63 1259
Number of pixels rejected : 474
Number of (internal) image counts : 124157
Number of image cts rejected (N, %) : 111943 90.1624527
By chip : 0 1 2 3
Pixels rejected : 108 184 79 103
Image counts : 29360 34696 30522 29579
Image cts rejected: 27357 32611 25387 26588
Image cts rej (%) : 93.18 93.99 83.18 89.89
filtering data...
Total counts : 29360 34696 30522 29579
Total cts rejected: 27357 32611 25387 26588
Total cts rej (%) : 93.18 93.99 83.18 89.89
Number of clean counts accepted : 12214
writing history cards...
copying extensions...
writing out hot pixs...
Number of rejected pixels : 474
updating NEVENTS keywords...
closing data file...
closing clean file...
Command not found; type ? for a command listing
!screen:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!screen:ASCA > set datadir .
Setting data directory to /data/data17/seq_proc/50006000.007/
Setting mkf directory to /data/data17/seq_proc/50006000.007/
!screen:ASCA > read events ad50006000s100102h.unf
Got new instrument: SIS1
Setting: IMAGE binning = 4
WMAP binning = 8
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 2047
Got the minimum time resolution of the read data: 16.000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data17/seq_proc/50006000.007/
HK Directory is: /data/data17/seq_proc/50006000.007/
!screen:ASCA-SIS1-BRIGHT > select event "grade==0||grade==2||grade==3||grade==4" save_file=no
!screen:ASCA-SIS1-BRIGHT > select mkf "@criteria.tmp" data_dir=. ASCA_mkf_def_expr=ft*.mkf
!screen:ASCA-SIS1-BRIGHT > extract events
!screen:ASCA-SIS1-BRIGHT > sisclean saoimage=no sis_plot=no clean=2 cellsize=5 log_prob=-5.24 bkg_thr=3 clean_phalow=0 clean_phahi=4095
!screen:ASCA-SIS1-BRIGHT > save clean outfile=ad50006000s100102h.evt use_events=no
Wrote cleaned events file to ad50006000s100102h.evt
!screen:ASCA-SIS1-BRIGHT > exit save_session=no
-> Filtering ad50006000s100112h.unf into ad50006000s100112h.evtThe sum of the selected column is 14155.512 The mean of the selected column is 31.667813 The standard deviation of the selected column is 17.632306 The minimum of selected column is 1.9719452 The maximum of selected column is 195.56310 The number of points used in calculation is 447-> Standard Output From FTOOL fstatistic:
The sum of the selected column is 14346.812 The mean of the selected column is 32.167740 The standard deviation of the selected column is 17.032225 The minimum of selected column is 1.0127584 The maximum of selected column is 188.43808 The number of points used in calculation is 446-> Standard Output From FTOOL fstatistic:
The sum of the selected column is 13865.688 The mean of the selected column is 31.019435 The standard deviation of the selected column is 20.509319 The minimum of selected column is 7.7812734 The maximum of selected column is 315.93851 The number of points used in calculation is 447-> Standard Output From FTOOL fstatistic:
The sum of the selected column is 13996.932 The mean of the selected column is 31.383255 The standard deviation of the selected column is 16.501261 The minimum of selected column is 0.78906512 The maximum of selected column is 139.37543 The number of points used in calculation is 446-> Using the following selection criteria:
(SAA==0) &&(BR_EARTH>20) &&(ELV>10) &&(COR>6) &&(ACS==0) &&(ANG_DIST>0)&& (ANG_DIST<0.01) &&(FOV==0) && ( (S1_PIXL0>0.0 && S1_PIXL0<84.5 )&& (S1_PIXL1>0.0 && S1_PIXL1<83.2 )&& (S1_PIXL2>0.0 && S1_PIXL2<92.5 )&& (S1_PIXL3>0.0 && S1_PIXL3<80.8 ) ) &&( (S1_SATF0<1) ||(S1_SATF0>1)) &&( (S1_SATF1<1) ||(S1_SATF1>1)) &&( (S1_SATF2<1) ||(S1_SATF2>1)) &&( (S1_SATF3<1) ||(S1_SATF3>1)) &&((T_DY_NT<0)||(T_DY_NT>64)) &&((T_SAA <0)||(T_SAA >64))-> Standard Output From FTOOL xselect:
** XSELECT V1.3 **
!> Enter session name >[xsel] screen
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS S1CCDPOW
1 W50 EAST BRIGHT2 HIGH 28/04/93 03:44:28 0.24E+05 187467 1111
Processing file: /data/data17/seq_proc/50006000.007/ad50006000s100112h.unf
EXTRACTOR vers 2.0 11 Apr 1997.
Doing file: /data/data17/seq_proc/50006000.007/screen_work1001.xsl
Total Good Bad: Region Time Phase Cut
172976 124592 0 48384 0 0
Writing events file
124592 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
172976 124592 0 48384 0 0
in 17516.77 seconds
CLEANSIS_V1.6
allocating image arrays...
PROGRAM TO MAKE AN SIS SCIENCE FILE CLEANED OF ANOMALOUS PIXELS.
* Anomalous pixels may consist of at least two populations.
1. Persistent HOT pixels are removed by comparing to the chip mean.
2. Flickering WARM pixels are removed by comparing to the cell mean.
3. In faint areas (zero bgd), flickering pixels are removed with a
cutoff threshold.
Hints:
Choose cell size and thresholds based on the expected background and the PSF.
Use the DIRTYSIS option to examine the anomalous pixel spectra.
Try a multiple pass clean:
Choose a PHA cut to optimize the S/N of the flickering pixels,
then a broad band clean.
Be suspicious of extended source cleans.
For very bright sources you may need to turn off the iteration option.
See the help page for further info (fhelp cleansis)
Poisson clean cell size : 5
Poisson probability threshold : 0.631E-05
Zero Bgd Cutoff threshold (>) : 3
Iterate : T
Dirtysis : F
Minimum PHA value (inclusive) : 0
Maximum PHA value (inclusive) : 4095
open output file: /data/data17/seq_proc/50006000.007/screen_in_event.xsl
reading data file: /data/data17/seq_proc/50006000.007/screen_out_event.xsl
copying primary header to output file...
making chip image...
Total counts in chip images : 124592
copy bad pix array...
cleaning chip # 0
Hot pixels & counts : 50 26115
Flickering pixels iter, pixels & cnts : 1 58 1270
cleaning chip # 1
Hot pixels & counts : 43 30827
Flickering pixels iter, pixels & cnts : 1 142 1830
cleaning chip # 2
Hot pixels & counts : 38 24596
Flickering pixels iter, pixels & cnts : 1 41 803
cleaning chip # 3
Hot pixels & counts : 40 25407
Flickering pixels iter, pixels & cnts : 1 63 1262
Number of pixels rejected : 475
Number of (internal) image counts : 124592
Number of image cts rejected (N, %) : 112110 89.9816971
By chip : 0 1 2 3
Pixels rejected : 108 185 79 103
Image counts : 29453 34804 30615 29720
Image cts rejected: 27385 32657 25399 26669
Image cts rej (%) : 92.98 93.83 82.96 89.73
filtering data...
Total counts : 29453 34804 30615 29720
Total cts rejected: 27385 32657 25399 26669
Total cts rej (%) : 92.98 93.83 82.96 89.73
Number of clean counts accepted : 12482
writing history cards...
copying extensions...
writing out hot pixs...
Number of rejected pixels : 475
updating NEVENTS keywords...
closing data file...
closing clean file...
Command not found; type ? for a command listing
!screen:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!screen:ASCA > set datadir .
Setting data directory to /data/data17/seq_proc/50006000.007/
Setting mkf directory to /data/data17/seq_proc/50006000.007/
!screen:ASCA > read events ad50006000s100112h.unf
Got new instrument: SIS1
Setting: IMAGE binning = 4
WMAP binning = 8
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 4095
Got the minimum time resolution of the read data: 16.000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data17/seq_proc/50006000.007/
HK Directory is: /data/data17/seq_proc/50006000.007/
!screen:ASCA-SIS1-BRIGHT2 > select event "grade==0||grade==2||grade==3||grade==4" save_file=no
!screen:ASCA-SIS1-BRIGHT2 > select mkf "@criteria.tmp" data_dir=. ASCA_mkf_def_expr=ft*.mkf
!screen:ASCA-SIS1-BRIGHT2 > extract events
!screen:ASCA-SIS1-BRIGHT2 > sisclean saoimage=no sis_plot=no clean=2 cellsize=5 log_prob=-5.24 bkg_thr=3 clean_phalow=0 clean_phahi=4095
!screen:ASCA-SIS1-BRIGHT2 > save clean outfile=ad50006000s100112h.evt use_events=no
Wrote cleaned events file to ad50006000s100112h.evt
!screen:ASCA-SIS1-BRIGHT2 > exit save_session=no
-> Filtering ad50006000s100202m.unf into ad50006000s100202m.evtThe sum of the selected column is 4211.3283 The mean of the selected column is 113.81968 The standard deviation of the selected column is 159.54683 The minimum of selected column is 3.6108153 The maximum of selected column is 693.22089 The number of points used in calculation is 37-> Standard Output From FTOOL fstatistic:
The sum of the selected column is 4215.2102 The mean of the selected column is 113.92460 The standard deviation of the selected column is 149.79749 The minimum of selected column is 1.7755779 The maximum of selected column is 648.93951 The number of points used in calculation is 37-> Standard Output From FTOOL fstatistic:
The sum of the selected column is 4758.6502 The mean of the selected column is 128.61217 The standard deviation of the selected column is 176.81003 The minimum of selected column is 13.937542 The maximum of selected column is 740.34607 The number of points used in calculation is 37-> Standard Output From FTOOL fstatistic:
The sum of the selected column is 4297.5217 The mean of the selected column is 116.14924 The standard deviation of the selected column is 151.43119 The minimum of selected column is 2.0710340 The maximum of selected column is 598.25183 The number of points used in calculation is 37-> Using the following selection criteria:
(SAA==0) &&(BR_EARTH>20) &&(ELV>10) &&(COR>6) &&(ACS==0) &&(ANG_DIST>0)&& (ANG_DIST<0.01) &&(FOV==0) && ( (S1_PIXL0>0.0 && S1_PIXL0<592.4 )&& (S1_PIXL1>0.0 && S1_PIXL1<563.3 )&& (S1_PIXL2>0.0 && S1_PIXL2<659 )&& (S1_PIXL3>0.0 && S1_PIXL3<570.4 ) ) &&( (S1_SATF0<1) ||(S1_SATF0>1)) &&( (S1_SATF1<1) ||(S1_SATF1>1)) &&( (S1_SATF2<1) ||(S1_SATF2>1)) &&( (S1_SATF3<1) ||(S1_SATF3>1)) &&((T_DY_NT<0)||(T_DY_NT>64)) &&((T_SAA <0)||(T_SAA >64))-> Standard Output From FTOOL xselect:
** XSELECT V1.3 **
!> Enter session name >[xsel] screen
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS S1CCDPOW
1 W50 EAST BRIGHT MEDIUM 27/04/93 23:50:32 0.32E+05 197039 1111
Processing file: /data/data17/seq_proc/50006000.007/ad50006000s100202m.unf
EXTRACTOR vers 2.0 11 Apr 1997.
Doing file: /data/data17/seq_proc/50006000.007/screen_work1001.xsl
Total Good Bad: Region Time Phase Cut
186237 79923 0 106314 0 0
Writing events file
79923 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
186237 79923 0 106314 0 0
in 11101.56 seconds
CLEANSIS_V1.6
allocating image arrays...
PROGRAM TO MAKE AN SIS SCIENCE FILE CLEANED OF ANOMALOUS PIXELS.
* Anomalous pixels may consist of at least two populations.
1. Persistent HOT pixels are removed by comparing to the chip mean.
2. Flickering WARM pixels are removed by comparing to the cell mean.
3. In faint areas (zero bgd), flickering pixels are removed with a
cutoff threshold.
Hints:
Choose cell size and thresholds based on the expected background and the PSF.
Use the DIRTYSIS option to examine the anomalous pixel spectra.
Try a multiple pass clean:
Choose a PHA cut to optimize the S/N of the flickering pixels,
then a broad band clean.
Be suspicious of extended source cleans.
For very bright sources you may need to turn off the iteration option.
See the help page for further info (fhelp cleansis)
Poisson clean cell size : 5
Poisson probability threshold : 0.631E-05
Zero Bgd Cutoff threshold (>) : 3
Iterate : T
Dirtysis : F
Minimum PHA value (inclusive) : 0
Maximum PHA value (inclusive) : 4095
open output file: /data/data17/seq_proc/50006000.007/screen_in_event.xsl
reading data file: /data/data17/seq_proc/50006000.007/screen_out_event.xsl
copying primary header to output file...
making chip image...
Total counts in chip images : 79923
copy bad pix array...
cleaning chip # 0
Hot pixels & counts : 44 17086
Flickering pixels iter, pixels & cnts : 1 50 792
cleaning chip # 1
Hot pixels & counts : 39 19858
Flickering pixels iter, pixels & cnts : 1 130 1318
Flickering pixels iter, pixels & cnts : 2 3 9
cleaning chip # 2
Hot pixels & counts : 38 16273
Flickering pixels iter, pixels & cnts : 1 31 452
cleaning chip # 3
Hot pixels & counts : 36 15436
Flickering pixels iter, pixels & cnts : 1 52 815
Number of pixels rejected : 423
Number of (internal) image counts : 79923
Number of image cts rejected (N, %) : 72039 90.1355057
By chip : 0 1 2 3
Pixels rejected : 94 172 69 88
Image counts : 19226 22526 20073 18098
Image cts rejected: 17878 21185 16725 16251
Image cts rej (%) : 92.99 94.05 83.32 89.79
filtering data...
Total counts : 19226 22526 20073 18098
Total cts rejected: 17878 21185 16725 16251
Total cts rej (%) : 92.99 94.05 83.32 89.79
Number of clean counts accepted : 7884
writing history cards...
copying extensions...
writing out hot pixs...
Number of rejected pixels : 423
updating NEVENTS keywords...
closing data file...
closing clean file...
Command not found; type ? for a command listing
!screen:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!screen:ASCA > set datadir .
Setting data directory to /data/data17/seq_proc/50006000.007/
Setting mkf directory to /data/data17/seq_proc/50006000.007/
!screen:ASCA > read events ad50006000s100202m.unf
Got new instrument: SIS1
Setting: IMAGE binning = 4
WMAP binning = 8
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 2047
Got the minimum time resolution of the read data: 16.000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data17/seq_proc/50006000.007/
HK Directory is: /data/data17/seq_proc/50006000.007/
!screen:ASCA-SIS1-BRIGHT > select event "grade==0||grade==2||grade==3||grade==4" save_file=no
!screen:ASCA-SIS1-BRIGHT > select mkf "@criteria.tmp" data_dir=. ASCA_mkf_def_expr=ft*.mkf
!screen:ASCA-SIS1-BRIGHT > extract events
!screen:ASCA-SIS1-BRIGHT > sisclean saoimage=no sis_plot=no clean=2 cellsize=5 log_prob=-5.24 bkg_thr=3 clean_phalow=0 clean_phahi=4095
!screen:ASCA-SIS1-BRIGHT > save clean outfile=ad50006000s100202m.evt use_events=no
Wrote cleaned events file to ad50006000s100202m.evt
!screen:ASCA-SIS1-BRIGHT > exit save_session=no
-> Filtering ad50006000s100302l.unf into ad50006000s100302l.evt(SAA==0) &&(BR_EARTH>20) &&(ELV>10) &&(COR>6) &&(ACS==0) &&(ANG_DIST>0)&& (ANG_DIST<0.01) &&(FOV==0) && ( (S1_PIXL0>0)&& (S1_PIXL1>0)&& (S1_PIXL2>0)&& (S1_PIXL3>0) ) &&( (S1_SATF0<1) ||(S1_SATF0>1)) &&( (S1_SATF1<1) ||(S1_SATF1>1)) &&( (S1_SATF2<1) ||(S1_SATF2>1)) &&( (S1_SATF3<1) ||(S1_SATF3>1)) &&((T_DY_NT<0)||(T_DY_NT>64)) &&((T_SAA <0)||(T_SAA >64))-> Standard Output From FTOOL xselect:
** XSELECT V1.3 **
!> Enter session name >[xsel] screen
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS S1CCDPOW
1 W50 EAST BRIGHT LOW 28/04/93 01:05:12 0.18E+04 5104 1111
Processing file: /data/data17/seq_proc/50006000.007/ad50006000s100302l.unf
EXTRACTOR vers 2.0 11 Apr 1997.
Skipping file: /data/data17/seq_proc/50006000.007/screen_work1001.xsl
Writing events file
0 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
0 0 0 0 0 0
in 0.00 seconds
CLEANSIS_V1.6
allocating image arrays...
PROGRAM TO MAKE AN SIS SCIENCE FILE CLEANED OF ANOMALOUS PIXELS.
* Anomalous pixels may consist of at least two populations.
1. Persistent HOT pixels are removed by comparing to the chip mean.
2. Flickering WARM pixels are removed by comparing to the cell mean.
3. In faint areas (zero bgd), flickering pixels are removed with a
cutoff threshold.
Hints:
Choose cell size and thresholds based on the expected background and the PSF.
Use the DIRTYSIS option to examine the anomalous pixel spectra.
Try a multiple pass clean:
Choose a PHA cut to optimize the S/N of the flickering pixels,
then a broad band clean.
Be suspicious of extended source cleans.
For very bright sources you may need to turn off the iteration option.
See the help page for further info (fhelp cleansis)
Poisson clean cell size : 5
Poisson probability threshold : 0.631E-05
Zero Bgd Cutoff threshold (>) : 3
Iterate : T
Dirtysis : F
Minimum PHA value (inclusive) : 0
Maximum PHA value (inclusive) : 4095
open output file: /data/data17/seq_proc/50006000.007/screen_in_event.xsl
reading data file: /data/data17/seq_proc/50006000.007/screen_out_event.xsl
copying primary header to output file...
making chip image...
Total counts in chip images : 0
copy bad pix array...
cleaning chip # 0
cleaning chip # 1
cleaning chip # 2
cleaning chip # 3
Number of pixels rejected : 0
Number of (internal) image counts : 0
Number of image cts rejected (N, %) : 0 0.0000000
By chip : 0 1 2 3
Pixels rejected : 0 0 0 0
Image counts : 0 0 0 0
Image cts rejected: 0 0 0 0
Image cts rej (%) : 0.00 0.00 0.00 0.00
filtering data...
Total counts : 0 0 0 0
Total cts rejected: 0 0 0 0
Total cts rej (%) : 0.00 0.00 0.00 0.00
Number of clean counts accepted : 0
writing history cards...
copying extensions...
writing out hot pixs...
Number of rejected pixels : 0
updating NEVENTS keywords...
closing data file...
closing clean file...
Command not found; type ? for a command listing
!screen:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!screen:ASCA > set datadir .
Setting data directory to /data/data17/seq_proc/50006000.007/
Setting mkf directory to /data/data17/seq_proc/50006000.007/
!screen:ASCA > read events ad50006000s100302l.unf
Got new instrument: SIS1
Setting: IMAGE binning = 4
WMAP binning = 8
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 2047
Got the minimum time resolution of the read data: 16.000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data17/seq_proc/50006000.007/
HK Directory is: /data/data17/seq_proc/50006000.007/
!screen:ASCA-SIS1-BRIGHT > select event "grade==0||grade==2||grade==3||grade==4" save_file=no
!screen:ASCA-SIS1-BRIGHT > select mkf "@criteria.tmp" data_dir=. ASCA_mkf_def_expr=ft*.mkf
!screen:ASCA-SIS1-BRIGHT > extract events
!screen:ASCA-SIS1-BRIGHT > sisclean saoimage=no sis_plot=no clean=2 cellsize=5 log_prob=-5.24 bkg_thr=3 clean_phalow=0 clean_phahi=4095
!screen:ASCA-SIS1-BRIGHT > save clean outfile=ad50006000s100302l.evt use_events=no
Wrote cleaned events file to ad50006000s100302l.evt
!screen:ASCA-SIS1-BRIGHT > exit save_session=no
-> Deleting ad50006000s100302l.evt since it contains 0 events(SAA==0) &&(BR_EARTH>20) &&(ELV>10) &&(COR>6) &&(ACS==0) &&(ANG_DIST>0)&& (ANG_DIST<0.01) &&(FOV==0) && ( (S1_PIXL0>0)&& (S1_PIXL1>0)&& (S1_PIXL2>0)&& (S1_PIXL3>0) ) &&( (S1_SATF0<1) ||(S1_SATF0>1)) &&( (S1_SATF1<1) ||(S1_SATF1>1)) &&( (S1_SATF2<1) ||(S1_SATF2>1)) &&( (S1_SATF3<1) ||(S1_SATF3>1)) &&((T_DY_NT<0)||(T_DY_NT>64)) &&((T_SAA <0)||(T_SAA >64))-> Standard Output From FTOOL xselect:
** XSELECT V1.3 **
!> Enter session name >[xsel] screen
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS S1CCDPOW
1 W50 EAST BRIGHT HIGH 28/04/93 14:13:12 0.15E+03 1052 1111
Processing file: /data/data17/seq_proc/50006000.007/ad50006000s100402h.unf
EXTRACTOR vers 2.0 11 Apr 1997.
Skipping file: /data/data17/seq_proc/50006000.007/screen_work1001.xsl
Writing events file
0 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
0 0 0 0 0 0
in 0.00 seconds
CLEANSIS_V1.6
allocating image arrays...
PROGRAM TO MAKE AN SIS SCIENCE FILE CLEANED OF ANOMALOUS PIXELS.
* Anomalous pixels may consist of at least two populations.
1. Persistent HOT pixels are removed by comparing to the chip mean.
2. Flickering WARM pixels are removed by comparing to the cell mean.
3. In faint areas (zero bgd), flickering pixels are removed with a
cutoff threshold.
Hints:
Choose cell size and thresholds based on the expected background and the PSF.
Use the DIRTYSIS option to examine the anomalous pixel spectra.
Try a multiple pass clean:
Choose a PHA cut to optimize the S/N of the flickering pixels,
then a broad band clean.
Be suspicious of extended source cleans.
For very bright sources you may need to turn off the iteration option.
See the help page for further info (fhelp cleansis)
Poisson clean cell size : 5
Poisson probability threshold : 0.631E-05
Zero Bgd Cutoff threshold (>) : 3
Iterate : T
Dirtysis : F
Minimum PHA value (inclusive) : 0
Maximum PHA value (inclusive) : 4095
open output file: /data/data17/seq_proc/50006000.007/screen_in_event.xsl
reading data file: /data/data17/seq_proc/50006000.007/screen_out_event.xsl
copying primary header to output file...
making chip image...
Total counts in chip images : 0
copy bad pix array...
cleaning chip # 0
cleaning chip # 1
cleaning chip # 2
cleaning chip # 3
Number of pixels rejected : 0
Number of (internal) image counts : 0
Number of image cts rejected (N, %) : 0 0.0000000
By chip : 0 1 2 3
Pixels rejected : 0 0 0 0
Image counts : 0 0 0 0
Image cts rejected: 0 0 0 0
Image cts rej (%) : 0.00 0.00 0.00 0.00
filtering data...
Total counts : 0 0 0 0
Total cts rejected: 0 0 0 0
Total cts rej (%) : 0.00 0.00 0.00 0.00
Number of clean counts accepted : 0
writing history cards...
copying extensions...
writing out hot pixs...
Number of rejected pixels : 0
updating NEVENTS keywords...
closing data file...
closing clean file...
Command not found; type ? for a command listing
!screen:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!screen:ASCA > set datadir .
Setting data directory to /data/data17/seq_proc/50006000.007/
Setting mkf directory to /data/data17/seq_proc/50006000.007/
!screen:ASCA > read events ad50006000s100402h.unf
Got new instrument: SIS1
Setting: IMAGE binning = 4
WMAP binning = 8
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 2047
Got the minimum time resolution of the read data: 16.000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data17/seq_proc/50006000.007/
HK Directory is: /data/data17/seq_proc/50006000.007/
!screen:ASCA-SIS1-BRIGHT > select event "grade==0||grade==2||grade==3||grade==4" save_file=no
!screen:ASCA-SIS1-BRIGHT > select mkf "@criteria.tmp" data_dir=. ASCA_mkf_def_expr=ft*.mkf
!screen:ASCA-SIS1-BRIGHT > extract events
!screen:ASCA-SIS1-BRIGHT > sisclean saoimage=no sis_plot=no clean=2 cellsize=5 log_prob=-5.24 bkg_thr=3 clean_phalow=0 clean_phahi=4095
!screen:ASCA-SIS1-BRIGHT > save clean outfile=ad50006000s100402h.evt use_events=no
Wrote cleaned events file to ad50006000s100402h.evt
!screen:ASCA-SIS1-BRIGHT > exit save_session=no
-> Deleting ad50006000s100402h.evt since it contains 0 eventsThe sum of the selected column is 4441.2216 The mean of the selected column is 30.419326 The standard deviation of the selected column is 15.589718 The minimum of selected column is 6.3437686 The maximum of selected column is 101.56280 The number of points used in calculation is 146-> Standard Output From FTOOL fstatistic:
The sum of the selected column is 4463.8778 The mean of the selected column is 30.574506 The standard deviation of the selected column is 13.759552 The minimum of selected column is 9.8437796 The maximum of selected column is 101.62531 The number of points used in calculation is 146-> Standard Output From FTOOL fstatistic:
The sum of the selected column is 4144.7207 The mean of the selected column is 28.388498 The standard deviation of the selected column is 14.624898 The minimum of selected column is 9.1875277 The maximum of selected column is 146.75043 The number of points used in calculation is 146-> Standard Output From FTOOL fstatistic:
The sum of the selected column is 4494.8884 The mean of the selected column is 30.786907 The standard deviation of the selected column is 12.924948 The minimum of selected column is 9.1562767 The maximum of selected column is 79.062744 The number of points used in calculation is 146-> Using the following selection criteria:
(SAA==0) &&(BR_EARTH>20) &&(ELV>10) &&(COR>6) &&(ACS==0) &&(ANG_DIST>0)&& (ANG_DIST<0.01) &&(FOV==0) && ( (S1_PIXL0>0.0 && S1_PIXL0<77.1 )&& (S1_PIXL1>0.0 && S1_PIXL1<71.8 )&& (S1_PIXL2>0.0 && S1_PIXL2<72.2 )&& (S1_PIXL3>0.0 && S1_PIXL3<69.5 ) ) &&( (S1_SATF0<1) ||(S1_SATF0>1)) &&( (S1_SATF1<1) ||(S1_SATF1>1)) &&( (S1_SATF2<1) ||(S1_SATF2>1)) &&( (S1_SATF3<1) ||(S1_SATF3>1)) &&((T_DY_NT<0)||(T_DY_NT>64)) &&((T_SAA <0)||(T_SAA >64))-> Standard Output From FTOOL xselect:
** XSELECT V1.3 **
!> Enter session name >[xsel] screen
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS S1CCDPOW
1 W50 EAST BRIGHT MEDIUM 28/04/93 19:50:16 0.12E+05 70315 1111
Processing file: /data/data17/seq_proc/50006000.007/ad50006000s100502m.unf
EXTRACTOR vers 2.0 11 Apr 1997.
Doing file: /data/data17/seq_proc/50006000.007/screen_work1001.xsl
Total Good Bad: Region Time Phase Cut
66637 39324 0 27313 0 0
Writing events file
39324 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
66637 39324 0 27313 0 0
in 5608.04 seconds
CLEANSIS_V1.6
allocating image arrays...
PROGRAM TO MAKE AN SIS SCIENCE FILE CLEANED OF ANOMALOUS PIXELS.
* Anomalous pixels may consist of at least two populations.
1. Persistent HOT pixels are removed by comparing to the chip mean.
2. Flickering WARM pixels are removed by comparing to the cell mean.
3. In faint areas (zero bgd), flickering pixels are removed with a
cutoff threshold.
Hints:
Choose cell size and thresholds based on the expected background and the PSF.
Use the DIRTYSIS option to examine the anomalous pixel spectra.
Try a multiple pass clean:
Choose a PHA cut to optimize the S/N of the flickering pixels,
then a broad band clean.
Be suspicious of extended source cleans.
For very bright sources you may need to turn off the iteration option.
See the help page for further info (fhelp cleansis)
Poisson clean cell size : 5
Poisson probability threshold : 0.631E-05
Zero Bgd Cutoff threshold (>) : 3
Iterate : T
Dirtysis : F
Minimum PHA value (inclusive) : 0
Maximum PHA value (inclusive) : 4095
open output file: /data/data17/seq_proc/50006000.007/screen_in_event.xsl
reading data file: /data/data17/seq_proc/50006000.007/screen_out_event.xsl
copying primary header to output file...
making chip image...
Total counts in chip images : 39324
copy bad pix array...
cleaning chip # 0
Hot pixels & counts : 41 8333
Flickering pixels iter, pixels & cnts : 1 41 504
cleaning chip # 1
Hot pixels & counts : 41 9800
Flickering pixels iter, pixels & cnts : 1 34 471
cleaning chip # 2
Hot pixels & counts : 33 7481
Flickering pixels iter, pixels & cnts : 1 22 315
cleaning chip # 3
Hot pixels & counts : 36 7944
Flickering pixels iter, pixels & cnts : 1 37 474
Number of pixels rejected : 285
Number of (internal) image counts : 39324
Number of image cts rejected (N, %) : 35322 89.8230057
By chip : 0 1 2 3
Pixels rejected : 82 75 55 73
Image counts : 9555 10885 9499 9385
Image cts rejected: 8837 10271 7796 8418
Image cts rej (%) : 92.49 94.36 82.07 89.70
filtering data...
Total counts : 9555 10885 9499 9385
Total cts rejected: 8837 10271 7796 8418
Total cts rej (%) : 92.49 94.36 82.07 89.70
Number of clean counts accepted : 4002
writing history cards...
copying extensions...
writing out hot pixs...
Number of rejected pixels : 285
updating NEVENTS keywords...
closing data file...
closing clean file...
Command not found; type ? for a command listing
!screen:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!screen:ASCA > set datadir .
Setting data directory to /data/data17/seq_proc/50006000.007/
Setting mkf directory to /data/data17/seq_proc/50006000.007/
!screen:ASCA > read events ad50006000s100502m.unf
Got new instrument: SIS1
Setting: IMAGE binning = 4
WMAP binning = 8
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 2047
Got the minimum time resolution of the read data: 16.000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data17/seq_proc/50006000.007/
HK Directory is: /data/data17/seq_proc/50006000.007/
!screen:ASCA-SIS1-BRIGHT > select event "grade==0||grade==2||grade==3||grade==4" save_file=no
!screen:ASCA-SIS1-BRIGHT > select mkf "@criteria.tmp" data_dir=. ASCA_mkf_def_expr=ft*.mkf
!screen:ASCA-SIS1-BRIGHT > extract events
!screen:ASCA-SIS1-BRIGHT > sisclean saoimage=no sis_plot=no clean=2 cellsize=5 log_prob=-5.24 bkg_thr=3 clean_phalow=0 clean_phahi=4095
!screen:ASCA-SIS1-BRIGHT > save clean outfile=ad50006000s100502m.evt use_events=no
Wrote cleaned events file to ad50006000s100502m.evt
!screen:ASCA-SIS1-BRIGHT > exit save_session=no
-> Skipping ad50006000s100601h.unf because of modeThe sum of the selected column is 1221.1078 The mean of the selected column is 26.545823 The standard deviation of the selected column is 19.408505 The minimum of selected column is 10.437531 The maximum of selected column is 136.59416 The number of points used in calculation is 46-> Standard Output From FTOOL fstatistic:
The sum of the selected column is 1549.9422 The mean of the selected column is 33.694395 The standard deviation of the selected column is 16.634093 The minimum of selected column is 12.812539 The maximum of selected column is 112.93784 The number of points used in calculation is 46-> Standard Output From FTOOL fstatistic:
The sum of the selected column is 1288.1914 The mean of the selected column is 28.004161 The standard deviation of the selected column is 14.694668 The minimum of selected column is 9.0625267 The maximum of selected column is 69.906456 The number of points used in calculation is 46-> Standard Output From FTOOL fstatistic:
The sum of the selected column is 1169.8160 The mean of the selected column is 25.430783 The standard deviation of the selected column is 10.668776 The minimum of selected column is 10.093781 The maximum of selected column is 70.750214 The number of points used in calculation is 46-> Using the following selection criteria:
(SAA==0) &&(BR_EARTH>20) &&(ELV>10) &&(COR>6) &&(ACS==0) &&(ANG_DIST>0)&& (ANG_DIST<0.01) &&(FOV==0) && ( (S1_PIXL0>0.0 && S1_PIXL0<84.7 )&& (S1_PIXL1>0.0 && S1_PIXL1<83.5 )&& (S1_PIXL2>0.0 && S1_PIXL2<72 )&& (S1_PIXL3>0.0 && S1_PIXL3<57.4 ) ) &&( (S1_SATF0<1) ||(S1_SATF0>1)) &&( (S1_SATF1<1) ||(S1_SATF1>1)) &&( (S1_SATF2<1) ||(S1_SATF2>1)) &&( (S1_SATF3<1) ||(S1_SATF3>1)) &&((T_DY_NT<0)||(T_DY_NT>64)) &&((T_SAA <0)||(T_SAA >64))-> Standard Output From FTOOL xselect:
** XSELECT V1.3 **
!> Enter session name >[xsel] screen
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS S1CCDPOW
1 W50 EAST BRIGHT HIGH 28/04/93 22:52:12 0.15E+04 11111 1111
Processing file: /data/data17/seq_proc/50006000.007/ad50006000s100602h.unf
EXTRACTOR vers 2.0 11 Apr 1997.
Doing file: /data/data17/seq_proc/50006000.007/screen_work1001.xsl
Total Good Bad: Region Time Phase Cut
10658 9767 0 891 0 0
Writing events file
9767 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
10658 9767 0 891 0 0
in 1421.93 seconds
CLEANSIS_V1.6
allocating image arrays...
PROGRAM TO MAKE AN SIS SCIENCE FILE CLEANED OF ANOMALOUS PIXELS.
* Anomalous pixels may consist of at least two populations.
1. Persistent HOT pixels are removed by comparing to the chip mean.
2. Flickering WARM pixels are removed by comparing to the cell mean.
3. In faint areas (zero bgd), flickering pixels are removed with a
cutoff threshold.
Hints:
Choose cell size and thresholds based on the expected background and the PSF.
Use the DIRTYSIS option to examine the anomalous pixel spectra.
Try a multiple pass clean:
Choose a PHA cut to optimize the S/N of the flickering pixels,
then a broad band clean.
Be suspicious of extended source cleans.
For very bright sources you may need to turn off the iteration option.
See the help page for further info (fhelp cleansis)
Poisson clean cell size : 5
Poisson probability threshold : 0.631E-05
Zero Bgd Cutoff threshold (>) : 3
Iterate : T
Dirtysis : F
Minimum PHA value (inclusive) : 0
Maximum PHA value (inclusive) : 4095
open output file: /data/data17/seq_proc/50006000.007/screen_in_event.xsl
reading data file: /data/data17/seq_proc/50006000.007/screen_out_event.xsl
copying primary header to output file...
making chip image...
Total counts in chip images : 9767
copy bad pix array...
cleaning chip # 0
Hot pixels & counts : 32 1996
Flickering pixels iter, pixels & cnts : 1 23 164
cleaning chip # 1
Hot pixels & counts : 35 2413
Flickering pixels iter, pixels & cnts : 1 20 125
cleaning chip # 2
Hot pixels & counts : 26 1808
Flickering pixels iter, pixels & cnts : 1 17 136
cleaning chip # 3
Hot pixels & counts : 28 1867
Flickering pixels iter, pixels & cnts : 1 23 163
Number of pixels rejected : 204
Number of (internal) image counts : 9767
Number of image cts rejected (N, %) : 8672 88.7887802
By chip : 0 1 2 3
Pixels rejected : 55 55 43 51
Image counts : 2342 2732 2407 2286
Image cts rejected: 2160 2538 1944 2030
Image cts rej (%) : 92.23 92.90 80.76 88.80
filtering data...
Total counts : 2342 2732 2407 2286
Total cts rejected: 2160 2538 1944 2030
Total cts rej (%) : 92.23 92.90 80.76 88.80
Number of clean counts accepted : 1095
writing history cards...
copying extensions...
writing out hot pixs...
Number of rejected pixels : 204
updating NEVENTS keywords...
closing data file...
closing clean file...
Command not found; type ? for a command listing
!screen:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!screen:ASCA > set datadir .
Setting data directory to /data/data17/seq_proc/50006000.007/
Setting mkf directory to /data/data17/seq_proc/50006000.007/
!screen:ASCA > read events ad50006000s100602h.unf
Got new instrument: SIS1
Setting: IMAGE binning = 4
WMAP binning = 8
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 2047
Got the minimum time resolution of the read data: 16.000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data17/seq_proc/50006000.007/
HK Directory is: /data/data17/seq_proc/50006000.007/
!screen:ASCA-SIS1-BRIGHT > select event "grade==0||grade==2||grade==3||grade==4" save_file=no
!screen:ASCA-SIS1-BRIGHT > select mkf "@criteria.tmp" data_dir=. ASCA_mkf_def_expr=ft*.mkf
!screen:ASCA-SIS1-BRIGHT > extract events
!screen:ASCA-SIS1-BRIGHT > sisclean saoimage=no sis_plot=no clean=2 cellsize=5 log_prob=-5.24 bkg_thr=3 clean_phalow=0 clean_phahi=4095
!screen:ASCA-SIS1-BRIGHT > save clean outfile=ad50006000s100602h.evt use_events=no
Wrote cleaned events file to ad50006000s100602h.evt
!screen:ASCA-SIS1-BRIGHT > exit save_session=no
-> Filtering ad50006000s100612h.unf into ad50006000s100612h.evtThe sum of the selected column is 1221.1078 The mean of the selected column is 26.545823 The standard deviation of the selected column is 19.408505 The minimum of selected column is 10.437531 The maximum of selected column is 136.59416 The number of points used in calculation is 46-> Standard Output From FTOOL fstatistic:
The sum of the selected column is 1549.9422 The mean of the selected column is 33.694395 The standard deviation of the selected column is 16.634093 The minimum of selected column is 12.812539 The maximum of selected column is 112.93784 The number of points used in calculation is 46-> Standard Output From FTOOL fstatistic:
The sum of the selected column is 1288.1914 The mean of the selected column is 28.004161 The standard deviation of the selected column is 14.694668 The minimum of selected column is 9.0625267 The maximum of selected column is 69.906456 The number of points used in calculation is 46-> Standard Output From FTOOL fstatistic:
The sum of the selected column is 1169.8160 The mean of the selected column is 25.430783 The standard deviation of the selected column is 10.668776 The minimum of selected column is 10.093781 The maximum of selected column is 70.750214 The number of points used in calculation is 46-> Using the following selection criteria:
(SAA==0) &&(BR_EARTH>20) &&(ELV>10) &&(COR>6) &&(ACS==0) &&(ANG_DIST>0)&& (ANG_DIST<0.01) &&(FOV==0) && ( (S1_PIXL0>0.0 && S1_PIXL0<84.7 )&& (S1_PIXL1>0.0 && S1_PIXL1<83.5 )&& (S1_PIXL2>0.0 && S1_PIXL2<72 )&& (S1_PIXL3>0.0 && S1_PIXL3<57.4 ) ) &&( (S1_SATF0<1) ||(S1_SATF0>1)) &&( (S1_SATF1<1) ||(S1_SATF1>1)) &&( (S1_SATF2<1) ||(S1_SATF2>1)) &&( (S1_SATF3<1) ||(S1_SATF3>1)) &&((T_DY_NT<0)||(T_DY_NT>64)) &&((T_SAA <0)||(T_SAA >64))-> Standard Output From FTOOL xselect:
** XSELECT V1.3 **
!> Enter session name >[xsel] screen
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS S1CCDPOW
1 W50 EAST BRIGHT2 HIGH 28/04/93 22:52:12 0.15E+04 11616 1111
Processing file: /data/data17/seq_proc/50006000.007/ad50006000s100612h.unf
EXTRACTOR vers 2.0 11 Apr 1997.
Doing file: /data/data17/seq_proc/50006000.007/screen_work1001.xsl
Total Good Bad: Region Time Phase Cut
10681 9788 0 893 0 0
Writing events file
9788 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
10681 9788 0 893 0 0
in 1421.93 seconds
CLEANSIS_V1.6
allocating image arrays...
PROGRAM TO MAKE AN SIS SCIENCE FILE CLEANED OF ANOMALOUS PIXELS.
* Anomalous pixels may consist of at least two populations.
1. Persistent HOT pixels are removed by comparing to the chip mean.
2. Flickering WARM pixels are removed by comparing to the cell mean.
3. In faint areas (zero bgd), flickering pixels are removed with a
cutoff threshold.
Hints:
Choose cell size and thresholds based on the expected background and the PSF.
Use the DIRTYSIS option to examine the anomalous pixel spectra.
Try a multiple pass clean:
Choose a PHA cut to optimize the S/N of the flickering pixels,
then a broad band clean.
Be suspicious of extended source cleans.
For very bright sources you may need to turn off the iteration option.
See the help page for further info (fhelp cleansis)
Poisson clean cell size : 5
Poisson probability threshold : 0.631E-05
Zero Bgd Cutoff threshold (>) : 3
Iterate : T
Dirtysis : F
Minimum PHA value (inclusive) : 0
Maximum PHA value (inclusive) : 4095
open output file: /data/data17/seq_proc/50006000.007/screen_in_event.xsl
reading data file: /data/data17/seq_proc/50006000.007/screen_out_event.xsl
copying primary header to output file...
making chip image...
Total counts in chip images : 9788
copy bad pix array...
cleaning chip # 0
Hot pixels & counts : 32 1996
Flickering pixels iter, pixels & cnts : 1 23 164
cleaning chip # 1
Hot pixels & counts : 35 2417
Flickering pixels iter, pixels & cnts : 1 20 125
cleaning chip # 2
Hot pixels & counts : 26 1808
Flickering pixels iter, pixels & cnts : 1 17 136
cleaning chip # 3
Hot pixels & counts : 29 1883
Flickering pixels iter, pixels & cnts : 1 22 148
Number of pixels rejected : 204
Number of (internal) image counts : 9788
Number of image cts rejected (N, %) : 8677 88.6493683
By chip : 0 1 2 3
Pixels rejected : 55 55 43 51
Image counts : 2349 2738 2410 2291
Image cts rejected: 2160 2542 1944 2031
Image cts rej (%) : 91.95 92.84 80.66 88.65
filtering data...
Total counts : 2349 2738 2410 2291
Total cts rejected: 2160 2542 1944 2031
Total cts rej (%) : 91.95 92.84 80.66 88.65
Number of clean counts accepted : 1111
writing history cards...
copying extensions...
writing out hot pixs...
Number of rejected pixels : 204
updating NEVENTS keywords...
closing data file...
closing clean file...
Command not found; type ? for a command listing
!screen:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!screen:ASCA > set datadir .
Setting data directory to /data/data17/seq_proc/50006000.007/
Setting mkf directory to /data/data17/seq_proc/50006000.007/
!screen:ASCA > read events ad50006000s100612h.unf
Got new instrument: SIS1
Setting: IMAGE binning = 4
WMAP binning = 8
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 4095
Got the minimum time resolution of the read data: 16.000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data17/seq_proc/50006000.007/
HK Directory is: /data/data17/seq_proc/50006000.007/
!screen:ASCA-SIS1-BRIGHT2 > select event "grade==0||grade==2||grade==3||grade==4" save_file=no
!screen:ASCA-SIS1-BRIGHT2 > select mkf "@criteria.tmp" data_dir=. ASCA_mkf_def_expr=ft*.mkf
!screen:ASCA-SIS1-BRIGHT2 > extract events
!screen:ASCA-SIS1-BRIGHT2 > sisclean saoimage=no sis_plot=no clean=2 cellsize=5 log_prob=-5.24 bkg_thr=3 clean_phalow=0 clean_phahi=4095
!screen:ASCA-SIS1-BRIGHT2 > save clean outfile=ad50006000s100612h.evt use_events=no
Wrote cleaned events file to ad50006000s100612h.evt
!screen:ASCA-SIS1-BRIGHT2 > exit save_session=no
-> Filtering ad50006000g200170m.unf into ad50006000g200170m.evt(SAA==0)&& (COR>4)&& (G2_H0+G2_H2+G3_H0+G3_H2<45)&& (G2_H0+G2_H2+G3_H0+G3_H2<0.45*COR**2-13*COR+125)&& (RBM_CONT<100)&& (ELV>5)&& (ACS==0)&& (ANG_DIST>0)&& (ANG_DIST<0.01)&& (G2_L1>0)-> Standard Output From FTOOL xselect:
** XSELECT V1.3 **
!> Enter session name >[xsel] screen
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS PHA_BINS
1 W50 EAST PH MEDIUM 27/04/93 23:50:48 0.27E+05 82925 1024
EXTRACTOR vers 2.0 11 Apr 1997.
Doing file: /data/data17/seq_proc/50006000.007/ad50006000g200170m.unf
Total Good Bad: Region Time Phase Cut
82925 8167 63193 11565 0 0
Writing events file
8167 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
82925 8167 63193 11565 0 0
in 11599.79 seconds
Infile # of rows Outfile # of rows # filtered
---------------- ----------------- ----------
8167 7555 612
Command not found; type ? for a command listing
!screen:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!screen:ASCA > set datadir .
Setting data directory to /data/data17/seq_proc/50006000.007/
Setting mkf directory to /data/data17/seq_proc/50006000.007/
!screen:ASCA > read events ad50006000g200170m.unf
Got new instrument: GIS2
Setting: IMAGE binning = 1
WMAP binning = 1
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 1023
Got the minimum time resolution of the read data: 0.50000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data17/seq_proc/50006000.007/
HK Directory is: /data/data17/seq_proc/50006000.007/
!screen:ASCA-GIS2-PH > filter region GIS2_REGION256_OFF.4
!screen:ASCA-GIS2-PH > select mkf "@criteria.tmp" data_dir=. ASCA_mkf_def_expr=ft*.mkf
!screen:ASCA-GIS2-PH > extract events
!screen:ASCA-GIS2-PH > gisclean
Using table:/opt/local/ftools/ftools.4.0.c/SunOS_5.4_sparc/refdata/rti_gis_1024_040693.fits
!screen:ASCA-GIS2-PH > save clean outfile=ad50006000g200170m.evt use_events=no
!screen:ASCA-GIS2-PH > exit save_session=no
-> Setting NEVENTS to 7555 in ad50006000g200170m.unf(SAA==0)&& (COR>4)&& (G2_H0+G2_H2+G3_H0+G3_H2<45)&& (G2_H0+G2_H2+G3_H0+G3_H2<0.45*COR**2-13*COR+125)&& (RBM_CONT<100)&& (ELV>5)&& (ACS==0)&& (ANG_DIST>0)&& (ANG_DIST<0.01)&& (G2_L1>0)-> Standard Output From FTOOL xselect:
** XSELECT V1.3 **
!> Enter session name >[xsel] screen
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS PHA_BINS
1 W50 EAST PH HIGH 28/04/93 03:44:46 0.24E+05 60324 1024
EXTRACTOR vers 2.0 11 Apr 1997.
Doing file: /data/data17/seq_proc/50006000.007/ad50006000g200270h.unf
Total Good Bad: Region Time Phase Cut
60324 12606 45247 2471 0 0
Writing events file
12606 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
60324 12606 45247 2471 0 0
in 17795.72 seconds
Infile # of rows Outfile # of rows # filtered
---------------- ----------------- ----------
12606 11655 951
Command not found; type ? for a command listing
!screen:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!screen:ASCA > set datadir .
Setting data directory to /data/data17/seq_proc/50006000.007/
Setting mkf directory to /data/data17/seq_proc/50006000.007/
!screen:ASCA > read events ad50006000g200270h.unf
Got new instrument: GIS2
Setting: IMAGE binning = 1
WMAP binning = 1
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 1023
Got the minimum time resolution of the read data: 0.62500E-01
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data17/seq_proc/50006000.007/
HK Directory is: /data/data17/seq_proc/50006000.007/
!screen:ASCA-GIS2-PH > filter region GIS2_REGION256_OFF.4
!screen:ASCA-GIS2-PH > select mkf "@criteria.tmp" data_dir=. ASCA_mkf_def_expr=ft*.mkf
!screen:ASCA-GIS2-PH > extract events
!screen:ASCA-GIS2-PH > gisclean
Using table:/opt/local/ftools/ftools.4.0.c/SunOS_5.4_sparc/refdata/rti_gis_1024_040693.fits
!screen:ASCA-GIS2-PH > save clean outfile=ad50006000g200270h.evt use_events=no
!screen:ASCA-GIS2-PH > exit save_session=no
-> Setting NEVENTS to 11655 in ad50006000g200270h.unf(SAA==0)&& (COR>4)&& (G2_H0+G2_H2+G3_H0+G3_H2<45)&& (G2_H0+G2_H2+G3_H0+G3_H2<0.45*COR**2-13*COR+125)&& (RBM_CONT<100)&& (ELV>5)&& (ACS==0)&& (ANG_DIST>0)&& (ANG_DIST<0.01)&& (G2_L1>0)-> Standard Output From FTOOL xselect:
** XSELECT V1.3 **
!> Enter session name >[xsel] screen
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS PHA_BINS
1 W50 EAST PH LOW 28/04/93 01:05:28 0.18E+04 4648 1024
EXTRACTOR vers 2.0 11 Apr 1997.
Skipping file: /data/data17/seq_proc/50006000.007/ad50006000g200370l.unf
Writing events file
0 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
0 0 0 0 0 0
in 0.00 seconds
Infile # of rows Outfile # of rows # filtered
---------------- ----------------- ----------
0 0 0
Command not found; type ? for a command listing
!screen:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!screen:ASCA > set datadir .
Setting data directory to /data/data17/seq_proc/50006000.007/
Setting mkf directory to /data/data17/seq_proc/50006000.007/
!screen:ASCA > read events ad50006000g200370l.unf
Got new instrument: GIS2
Setting: IMAGE binning = 1
WMAP binning = 1
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 1023
Got the minimum time resolution of the read data: 2.0000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data17/seq_proc/50006000.007/
HK Directory is: /data/data17/seq_proc/50006000.007/
!screen:ASCA-GIS2-PH > filter region GIS2_REGION256_OFF.4
!screen:ASCA-GIS2-PH > select mkf "@criteria.tmp" data_dir=. ASCA_mkf_def_expr=ft*.mkf
!screen:ASCA-GIS2-PH > extract events
!screen:ASCA-GIS2-PH > gisclean
Using table:/opt/local/ftools/ftools.4.0.c/SunOS_5.4_sparc/refdata/rti_gis_1024_040693.fits
!screen:ASCA-GIS2-PH > save clean outfile=ad50006000g200370l.evt use_events=no
!screen:ASCA-GIS2-PH > exit save_session=no
-> Deleting ad50006000g200370l.evt since it contains 0 events(SAA==0)&& (COR>4)&& (G2_H0+G2_H2+G3_H0+G3_H2<45)&& (G2_H0+G2_H2+G3_H0+G3_H2<0.45*COR**2-13*COR+125)&& (RBM_CONT<100)&& (ELV>5)&& (ACS==0)&& (ANG_DIST>0)&& (ANG_DIST<0.01)&& (G2_L1>0)-> Standard Output From FTOOL xselect:
** XSELECT V1.3 **
!> Enter session name >[xsel] screen
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS PHA_BINS
1 W50 EAST PH MEDIUM 28/04/93 19:50:32 0.99E+04 26977 1024
EXTRACTOR vers 2.0 11 Apr 1997.
Doing file: /data/data17/seq_proc/50006000.007/ad50006000g200470m.unf
Total Good Bad: Region Time Phase Cut
26977 4622 19200 3155 0 0
Writing events file
4622 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
26977 4622 19200 3155 0 0
in 6768.03 seconds
Infile # of rows Outfile # of rows # filtered
---------------- ----------------- ----------
4622 4255 367
Command not found; type ? for a command listing
!screen:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!screen:ASCA > set datadir .
Setting data directory to /data/data17/seq_proc/50006000.007/
Setting mkf directory to /data/data17/seq_proc/50006000.007/
!screen:ASCA > read events ad50006000g200470m.unf
Got new instrument: GIS2
Setting: IMAGE binning = 1
WMAP binning = 1
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 1023
Got the minimum time resolution of the read data: 0.50000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data17/seq_proc/50006000.007/
HK Directory is: /data/data17/seq_proc/50006000.007/
!screen:ASCA-GIS2-PH > filter region GIS2_REGION256_OFF.4
!screen:ASCA-GIS2-PH > select mkf "@criteria.tmp" data_dir=. ASCA_mkf_def_expr=ft*.mkf
!screen:ASCA-GIS2-PH > extract events
!screen:ASCA-GIS2-PH > gisclean
Using table:/opt/local/ftools/ftools.4.0.c/SunOS_5.4_sparc/refdata/rti_gis_1024_040693.fits
!screen:ASCA-GIS2-PH > save clean outfile=ad50006000g200470m.evt use_events=no
!screen:ASCA-GIS2-PH > exit save_session=no
-> Setting NEVENTS to 4255 in ad50006000g200470m.unf(SAA==0)&& (COR>4)&& (G2_H0+G2_H2+G3_H0+G3_H2<45)&& (G2_H0+G2_H2+G3_H0+G3_H2<0.45*COR**2-13*COR+125)&& (RBM_CONT<100)&& (ELV>5)&& (ACS==0)&& (ANG_DIST>0)&& (ANG_DIST<0.01)&& (G2_L1>0)-> Standard Output From FTOOL xselect:
** XSELECT V1.3 **
!> Enter session name >[xsel] screen
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS PHA_BINS
1 W50 EAST PH HIGH 28/04/93 22:52:30 0.15E+04 3692 1024
EXTRACTOR vers 2.0 11 Apr 1997.
Doing file: /data/data17/seq_proc/50006000.007/ad50006000g200570h.unf
Total Good Bad: Region Time Phase Cut
3692 1070 2622 0 0 0
Writing events file
1070 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
3692 1070 2622 0 0 0
in 1530.00 seconds
Infile # of rows Outfile # of rows # filtered
---------------- ----------------- ----------
1070 1004 66
Command not found; type ? for a command listing
!screen:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!screen:ASCA > set datadir .
Setting data directory to /data/data17/seq_proc/50006000.007/
Setting mkf directory to /data/data17/seq_proc/50006000.007/
!screen:ASCA > read events ad50006000g200570h.unf
Got new instrument: GIS2
Setting: IMAGE binning = 1
WMAP binning = 1
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 1023
Got the minimum time resolution of the read data: 0.62500E-01
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data17/seq_proc/50006000.007/
HK Directory is: /data/data17/seq_proc/50006000.007/
!screen:ASCA-GIS2-PH > filter region GIS2_REGION256_OFF.4
!screen:ASCA-GIS2-PH > select mkf "@criteria.tmp" data_dir=. ASCA_mkf_def_expr=ft*.mkf
!screen:ASCA-GIS2-PH > extract events
!screen:ASCA-GIS2-PH > gisclean
Using table:/opt/local/ftools/ftools.4.0.c/SunOS_5.4_sparc/refdata/rti_gis_1024_040693.fits
!screen:ASCA-GIS2-PH > save clean outfile=ad50006000g200570h.evt use_events=no
!screen:ASCA-GIS2-PH > exit save_session=no
-> Setting NEVENTS to 1004 in ad50006000g200570h.unf(SAA==0)&& (COR>4)&& (G2_H0+G2_H2+G3_H0+G3_H2<45)&& (G2_H0+G2_H2+G3_H0+G3_H2<0.45*COR**2-13*COR+125)&& (RBM_CONT<100)&& (ELV>5)&& (ACS==0)&& (ANG_DIST>0)&& (ANG_DIST<0.01)&& (G3_L1>0)-> Standard Output From FTOOL xselect:
** XSELECT V1.3 **
!> Enter session name >[xsel] screen
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS PHA_BINS
1 W50 EAST PH MEDIUM 27/04/93 23:50:48 0.27E+05 79675 1024
EXTRACTOR vers 2.0 11 Apr 1997.
Doing file: /data/data17/seq_proc/50006000.007/ad50006000g300170m.unf
Total Good Bad: Region Time Phase Cut
79675 7884 61236 10555 0 0
Writing events file
7884 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
79675 7884 61236 10555 0 0
in 11599.79 seconds
Infile # of rows Outfile # of rows # filtered
---------------- ----------------- ----------
7884 7421 463
Command not found; type ? for a command listing
!screen:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!screen:ASCA > set datadir .
Setting data directory to /data/data17/seq_proc/50006000.007/
Setting mkf directory to /data/data17/seq_proc/50006000.007/
!screen:ASCA > read events ad50006000g300170m.unf
Got new instrument: GIS3
Setting: IMAGE binning = 1
WMAP binning = 1
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 1023
Got the minimum time resolution of the read data: 0.50000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data17/seq_proc/50006000.007/
HK Directory is: /data/data17/seq_proc/50006000.007/
!screen:ASCA-GIS3-PH > filter region GIS3_REGION256_OFF.4
!screen:ASCA-GIS3-PH > select mkf "@criteria.tmp" data_dir=. ASCA_mkf_def_expr=ft*.mkf
!screen:ASCA-GIS3-PH > extract events
!screen:ASCA-GIS3-PH > gisclean
Using table:/opt/local/ftools/ftools.4.0.c/SunOS_5.4_sparc/refdata/rti_gis_1024_040693.fits
!screen:ASCA-GIS3-PH > save clean outfile=ad50006000g300170m.evt use_events=no
!screen:ASCA-GIS3-PH > exit save_session=no
-> Setting NEVENTS to 7421 in ad50006000g300170m.unf(SAA==0)&& (COR>4)&& (G2_H0+G2_H2+G3_H0+G3_H2<45)&& (G2_H0+G2_H2+G3_H0+G3_H2<0.45*COR**2-13*COR+125)&& (RBM_CONT<100)&& (ELV>5)&& (ACS==0)&& (ANG_DIST>0)&& (ANG_DIST<0.01)&& (G3_L1>0)-> Standard Output From FTOOL xselect:
** XSELECT V1.3 **
!> Enter session name >[xsel] screen
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS PHA_BINS
1 W50 EAST PH HIGH 28/04/93 03:44:46 0.24E+05 57073 1024
EXTRACTOR vers 2.0 11 Apr 1997.
Doing file: /data/data17/seq_proc/50006000.007/ad50006000g300270h.unf
Total Good Bad: Region Time Phase Cut
57073 12064 42847 2162 0 0
Writing events file
12064 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
57073 12064 42847 2162 0 0
in 17799.72 seconds
Infile # of rows Outfile # of rows # filtered
---------------- ----------------- ----------
12064 11260 804
Command not found; type ? for a command listing
!screen:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!screen:ASCA > set datadir .
Setting data directory to /data/data17/seq_proc/50006000.007/
Setting mkf directory to /data/data17/seq_proc/50006000.007/
!screen:ASCA > read events ad50006000g300270h.unf
Got new instrument: GIS3
Setting: IMAGE binning = 1
WMAP binning = 1
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 1023
Got the minimum time resolution of the read data: 0.62500E-01
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data17/seq_proc/50006000.007/
HK Directory is: /data/data17/seq_proc/50006000.007/
!screen:ASCA-GIS3-PH > filter region GIS3_REGION256_OFF.4
!screen:ASCA-GIS3-PH > select mkf "@criteria.tmp" data_dir=. ASCA_mkf_def_expr=ft*.mkf
!screen:ASCA-GIS3-PH > extract events
!screen:ASCA-GIS3-PH > gisclean
Using table:/opt/local/ftools/ftools.4.0.c/SunOS_5.4_sparc/refdata/rti_gis_1024_040693.fits
!screen:ASCA-GIS3-PH > save clean outfile=ad50006000g300270h.evt use_events=no
!screen:ASCA-GIS3-PH > exit save_session=no
-> Setting NEVENTS to 11260 in ad50006000g300270h.unf(SAA==0)&& (COR>4)&& (G2_H0+G2_H2+G3_H0+G3_H2<45)&& (G2_H0+G2_H2+G3_H0+G3_H2<0.45*COR**2-13*COR+125)&& (RBM_CONT<100)&& (ELV>5)&& (ACS==0)&& (ANG_DIST>0)&& (ANG_DIST<0.01)&& (G3_L1>0)-> Standard Output From FTOOL xselect:
** XSELECT V1.3 **
!> Enter session name >[xsel] screen
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS PHA_BINS
1 W50 EAST PH LOW 28/04/93 01:05:28 0.18E+04 4709 1024
EXTRACTOR vers 2.0 11 Apr 1997.
Skipping file: /data/data17/seq_proc/50006000.007/ad50006000g300370l.unf
Writing events file
0 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
0 0 0 0 0 0
in 0.00 seconds
Infile # of rows Outfile # of rows # filtered
---------------- ----------------- ----------
0 0 0
Command not found; type ? for a command listing
!screen:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!screen:ASCA > set datadir .
Setting data directory to /data/data17/seq_proc/50006000.007/
Setting mkf directory to /data/data17/seq_proc/50006000.007/
!screen:ASCA > read events ad50006000g300370l.unf
Got new instrument: GIS3
Setting: IMAGE binning = 1
WMAP binning = 1
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 1023
Got the minimum time resolution of the read data: 2.0000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data17/seq_proc/50006000.007/
HK Directory is: /data/data17/seq_proc/50006000.007/
!screen:ASCA-GIS3-PH > filter region GIS3_REGION256_OFF.4
!screen:ASCA-GIS3-PH > select mkf "@criteria.tmp" data_dir=. ASCA_mkf_def_expr=ft*.mkf
!screen:ASCA-GIS3-PH > extract events
!screen:ASCA-GIS3-PH > gisclean
Using table:/opt/local/ftools/ftools.4.0.c/SunOS_5.4_sparc/refdata/rti_gis_1024_040693.fits
!screen:ASCA-GIS3-PH > save clean outfile=ad50006000g300370l.evt use_events=no
!screen:ASCA-GIS3-PH > exit save_session=no
-> Deleting ad50006000g300370l.evt since it contains 0 events(SAA==0)&& (COR>4)&& (G2_H0+G2_H2+G3_H0+G3_H2<45)&& (G2_H0+G2_H2+G3_H0+G3_H2<0.45*COR**2-13*COR+125)&& (RBM_CONT<100)&& (ELV>5)&& (ACS==0)&& (ANG_DIST>0)&& (ANG_DIST<0.01)&& (G3_L1>0)-> Standard Output From FTOOL xselect:
** XSELECT V1.3 **
!> Enter session name >[xsel] screen
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS PHA_BINS
1 W50 EAST PH MEDIUM 28/04/93 19:50:32 0.99E+04 26610 1024
EXTRACTOR vers 2.0 11 Apr 1997.
Doing file: /data/data17/seq_proc/50006000.007/ad50006000g300470m.unf
Total Good Bad: Region Time Phase Cut
26610 4574 19279 2757 0 0
Writing events file
4574 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
26610 4574 19279 2757 0 0
in 6768.03 seconds
Infile # of rows Outfile # of rows # filtered
---------------- ----------------- ----------
4574 4275 299
Command not found; type ? for a command listing
!screen:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!screen:ASCA > set datadir .
Setting data directory to /data/data17/seq_proc/50006000.007/
Setting mkf directory to /data/data17/seq_proc/50006000.007/
!screen:ASCA > read events ad50006000g300470m.unf
Got new instrument: GIS3
Setting: IMAGE binning = 1
WMAP binning = 1
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 1023
Got the minimum time resolution of the read data: 0.50000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data17/seq_proc/50006000.007/
HK Directory is: /data/data17/seq_proc/50006000.007/
!screen:ASCA-GIS3-PH > filter region GIS3_REGION256_OFF.4
!screen:ASCA-GIS3-PH > select mkf "@criteria.tmp" data_dir=. ASCA_mkf_def_expr=ft*.mkf
!screen:ASCA-GIS3-PH > extract events
!screen:ASCA-GIS3-PH > gisclean
Using table:/opt/local/ftools/ftools.4.0.c/SunOS_5.4_sparc/refdata/rti_gis_1024_040693.fits
!screen:ASCA-GIS3-PH > save clean outfile=ad50006000g300470m.evt use_events=no
!screen:ASCA-GIS3-PH > exit save_session=no
-> Setting NEVENTS to 4275 in ad50006000g300470m.unf(SAA==0)&& (COR>4)&& (G2_H0+G2_H2+G3_H0+G3_H2<45)&& (G2_H0+G2_H2+G3_H0+G3_H2<0.45*COR**2-13*COR+125)&& (RBM_CONT<100)&& (ELV>5)&& (ACS==0)&& (ANG_DIST>0)&& (ANG_DIST<0.01)&& (G3_L1>0)-> Standard Output From FTOOL xselect:
** XSELECT V1.3 **
!> Enter session name >[xsel] screen
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS PHA_BINS
1 W50 EAST PH HIGH 28/04/93 22:52:30 0.15E+04 3482 1024
EXTRACTOR vers 2.0 11 Apr 1997.
Doing file: /data/data17/seq_proc/50006000.007/ad50006000g300570h.unf
Total Good Bad: Region Time Phase Cut
3482 1063 2419 0 0 0
Writing events file
1063 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
3482 1063 2419 0 0 0
in 1530.00 seconds
Infile # of rows Outfile # of rows # filtered
---------------- ----------------- ----------
1063 1006 57
Command not found; type ? for a command listing
!screen:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!screen:ASCA > set datadir .
Setting data directory to /data/data17/seq_proc/50006000.007/
Setting mkf directory to /data/data17/seq_proc/50006000.007/
!screen:ASCA > read events ad50006000g300570h.unf
Got new instrument: GIS3
Setting: IMAGE binning = 1
WMAP binning = 1
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 1023
Got the minimum time resolution of the read data: 0.62500E-01
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data17/seq_proc/50006000.007/
HK Directory is: /data/data17/seq_proc/50006000.007/
!screen:ASCA-GIS3-PH > filter region GIS3_REGION256_OFF.4
!screen:ASCA-GIS3-PH > select mkf "@criteria.tmp" data_dir=. ASCA_mkf_def_expr=ft*.mkf
!screen:ASCA-GIS3-PH > extract events
!screen:ASCA-GIS3-PH > gisclean
Using table:/opt/local/ftools/ftools.4.0.c/SunOS_5.4_sparc/refdata/rti_gis_1024_040693.fits
!screen:ASCA-GIS3-PH > save clean outfile=ad50006000g300570h.evt use_events=no
!screen:ASCA-GIS3-PH > exit save_session=no
-> Setting NEVENTS to 1006 in ad50006000g300570h.unf-ANNULUS(128.5,128.5,192,81) -ELLIPSE(167.5,220,24.66,28.95,245.298)-> gis2_ano_on_flf_180295.fits already present in current directory
ASCAEXPO_V0.9b
reading data file: ad50006000g200170m.evt
reading gti ext: STDGTI
reading cal file: gis2_ano_on_flf_180295.fits
reading inst file: GIS2_REGION256_OFF.4_regionmap.tmp
making an inst map...
multiply inst map...
reading att file: ./fa930427_2350.1950
making an exposure map...
Aspect RA/DEC/ROLL : 288.4410 4.9767 286.0802
Mean RA/DEC/ROLL : 288.4436 4.9495 286.0802
Pnt RA/DEC/ROLL : 288.2613 5.0758 286.0802
Image rebin factor : 1
Attitude Records : 61026
GTI intervals : 18
Total GTI (secs) : 11599.793
Max attitude excursion (arcsecs) : 5.000
0 Percent Complete: Total/live time: 0.0000000 0.0000000
10 Percent Complete: Total/live time: 1643.9914551 1643.9914551
20 Percent Complete: Total/live time: 2880.0000000 2880.0000000
30 Percent Complete: Total/live time: 3635.9975586 3635.9975586
40 Percent Complete: Total/live time: 5467.9912109 5467.9912109
50 Percent Complete: Total/live time: 6096.0229492 6096.0229492
60 Percent Complete: Total/live time: 7119.9780273 7119.9780273
70 Percent Complete: Total/live time: 9935.9785156 9935.9785156
80 Percent Complete: Total/live time: 9935.9785156 9935.9785156
90 Percent Complete: Total/live time: 10719.8964844 10719.8964844
100 Percent Complete: Total/live time: 11599.7919922 11599.7919922
Number of attitude steps used: 54
Number of attitude steps avail: 5867
Mean RA/DEC pixel offset: -12.1156 -3.7124
writing expo file: ad50006000g200170m.expo
closing attitude file...
closing data file...
-> Generating low and high energy images for ad50006000g200170m.evt
** XSELECT V1.3 **
!> Enter session name >[xsel] ad50006000g200170m
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS PHA_BINS
1 W50 EAST PH MEDIUM 27/04/93 23:50:48 0.12E+05 7555 1024
EXTRACTOR vers 2.0 11 Apr 1997.
Getting FITS WCS Keywords
Doing file: /data/data17/seq_proc/50006000.007/ad50006000g200170m.evt
Total Good Bad: Region Time Phase Cut
7555 7555 0 0 0 0
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
7555 7555 0 0 0 0
in 11599.79 seconds
Image has 7555 counts for 0.6513 counts/sec
EXTRACTOR vers 2.0 11 Apr 1997.
Getting FITS WCS Keywords
Doing file: /data/data17/seq_proc/50006000.007/ad50006000g200170m.evt
Total Good Bad: Region Time Phase Cut
7555 3696 0 0 0 3859
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
7555 3696 0 0 0 3859
in 11599.79 seconds
Image has 3696 counts for 0.3186 counts/sec
EXTRACTOR vers 2.0 11 Apr 1997.
Getting FITS WCS Keywords
Doing file: /data/data17/seq_proc/50006000.007/ad50006000g200170m.evt
Total Good Bad: Region Time Phase Cut
7555 3896 0 0 0 3659
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
7555 3896 0 0 0 3659
in 11599.79 seconds
Image has 3896 counts for 0.3359 counts/sec
Command not found; type ? for a command listing
!ad50006000g200170m:ASCA >
!ad50006000g200170m:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!ad50006000g200170m:ASCA > set datadir .
Setting data directory to /data/data17/seq_proc/50006000.007/
Setting mkf directory to /data/data17/seq_proc/50006000.007/
!ad50006000g200170m:ASCA > read events ad50006000g200170m.evt
Got new instrument: GIS2
Setting: IMAGE binning = 1
WMAP binning = 1
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 1023
Got the minimum time resolution of the read data: 0.50000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data17/seq_proc/50006000.007/
HK Directory is: /data/data17/seq_proc/50006000.007/
!ad50006000g200170m:ASCA-GIS2-PH > set image sky
!ad50006000g200170m:ASCA-GIS2-PH > filter region corner_point.reg
!ad50006000g200170m:ASCA-GIS2-PH > extract image
!ad50006000g200170m:ASCA-GIS2-PH > save image outfile=ad50006000g200170m.img
Wrote image to file ad50006000g200170m.img
!ad50006000g200170m:ASCA-GIS2-PH > filter pha_cut 0 170
!ad50006000g200170m:ASCA-GIS2-PH > extract image
!ad50006000g200170m:ASCA-GIS2-PH > save image outfile=ad50006000g200170m_lo.img
Wrote image to file ad50006000g200170m_lo.img
!ad50006000g200170m:ASCA-GIS2-PH > clear pha_cut
!ad50006000g200170m:ASCA-GIS2-PH > filter pha_cut 170 1024
Warning: your PI upper bound: 1024 is above the maximum value.
!ad50006000g200170m:ASCA-GIS2-PH > extract image
!ad50006000g200170m:ASCA-GIS2-PH > save image outfile=ad50006000g200170m_hi.img
Wrote image to file ad50006000g200170m_hi.img
!ad50006000g200170m:ASCA-GIS2-PH > exit save_session=no
-> Generating exposure map ad50006000g200270h.expo
ASCAEXPO_V0.9b
reading data file: ad50006000g200270h.evt
reading gti ext: STDGTI
reading cal file: gis2_ano_on_flf_180295.fits
reading inst file: GIS2_REGION256_OFF.4_regionmap.tmp
making an inst map...
multiply inst map...
reading att file: ./fa930427_2350.1950
making an exposure map...
Aspect RA/DEC/ROLL : 288.4410 4.9767 286.0800
Mean RA/DEC/ROLL : 288.4425 4.9518 286.0800
Pnt RA/DEC/ROLL : 288.4447 5.0002 286.0800
Image rebin factor : 1
Attitude Records : 61026
GTI intervals : 31
Total GTI (secs) : 17795.715
Max attitude excursion (arcsecs) : 5.000
0 Percent Complete: Total/live time: 0.0000000 0.0000000
10 Percent Complete: Total/live time: 2962.1303711 2962.1303711
20 Percent Complete: Total/live time: 4022.2299805 4022.2299805
30 Percent Complete: Total/live time: 6014.0922852 6014.0922852
40 Percent Complete: Total/live time: 7455.9345703 7455.9345703
50 Percent Complete: Total/live time: 9789.9267578 9789.9267578
60 Percent Complete: Total/live time: 10861.7392578 10861.7392578
70 Percent Complete: Total/live time: 12875.7333984 12875.7333984
80 Percent Complete: Total/live time: 16055.9394531 16055.9394531
90 Percent Complete: Total/live time: 16401.7207031 16401.7207031
100 Percent Complete: Total/live time: 17795.7207031 17795.7207031
Number of attitude steps used: 38
Number of attitude steps avail: 46683
Mean RA/DEC pixel offset: -11.8504 -2.6477
writing expo file: ad50006000g200270h.expo
closing attitude file...
closing data file...
-> Generating low and high energy images for ad50006000g200270h.evt
** XSELECT V1.3 **
!> Enter session name >[xsel] ad50006000g200270h
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS PHA_BINS
1 W50 EAST PH HIGH 28/04/93 03:44:46 0.18E+05 11655 1024
EXTRACTOR vers 2.0 11 Apr 1997.
Getting FITS WCS Keywords
Doing file: /data/data17/seq_proc/50006000.007/ad50006000g200270h.evt
Total Good Bad: Region Time Phase Cut
11655 11655 0 0 0 0
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
11655 11655 0 0 0 0
in 17795.72 seconds
Image has 11655 counts for 0.6549 counts/sec
EXTRACTOR vers 2.0 11 Apr 1997.
Getting FITS WCS Keywords
Doing file: /data/data17/seq_proc/50006000.007/ad50006000g200270h.evt
Total Good Bad: Region Time Phase Cut
11655 5671 0 0 0 5984
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
11655 5671 0 0 0 5984
in 17795.72 seconds
Image has 5671 counts for 0.3187 counts/sec
EXTRACTOR vers 2.0 11 Apr 1997.
Getting FITS WCS Keywords
Doing file: /data/data17/seq_proc/50006000.007/ad50006000g200270h.evt
Total Good Bad: Region Time Phase Cut
11655 6026 0 0 0 5629
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
11655 6026 0 0 0 5629
in 17795.72 seconds
Image has 6026 counts for 0.3386 counts/sec
Command not found; type ? for a command listing
!ad50006000g200270h:ASCA >
!ad50006000g200270h:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!ad50006000g200270h:ASCA > set datadir .
Setting data directory to /data/data17/seq_proc/50006000.007/
Setting mkf directory to /data/data17/seq_proc/50006000.007/
!ad50006000g200270h:ASCA > read events ad50006000g200270h.evt
Got new instrument: GIS2
Setting: IMAGE binning = 1
WMAP binning = 1
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 1023
Got the minimum time resolution of the read data: 0.62500E-01
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data17/seq_proc/50006000.007/
HK Directory is: /data/data17/seq_proc/50006000.007/
!ad50006000g200270h:ASCA-GIS2-PH > set image sky
!ad50006000g200270h:ASCA-GIS2-PH > filter region corner_point.reg
!ad50006000g200270h:ASCA-GIS2-PH > extract image
!ad50006000g200270h:ASCA-GIS2-PH > save image outfile=ad50006000g200270h.img
Wrote image to file ad50006000g200270h.img
!ad50006000g200270h:ASCA-GIS2-PH > filter pha_cut 0 170
!ad50006000g200270h:ASCA-GIS2-PH > extract image
!ad50006000g200270h:ASCA-GIS2-PH > save image outfile=ad50006000g200270h_lo.img
Wrote image to file ad50006000g200270h_lo.img
!ad50006000g200270h:ASCA-GIS2-PH > clear pha_cut
!ad50006000g200270h:ASCA-GIS2-PH > filter pha_cut 170 1024
Warning: your PI upper bound: 1024 is above the maximum value.
!ad50006000g200270h:ASCA-GIS2-PH > extract image
!ad50006000g200270h:ASCA-GIS2-PH > save image outfile=ad50006000g200270h_hi.img
Wrote image to file ad50006000g200270h_hi.img
!ad50006000g200270h:ASCA-GIS2-PH > exit save_session=no
-> Generating exposure map ad50006000g200470m.expo
ASCAEXPO_V0.9b
reading data file: ad50006000g200470m.evt
reading gti ext: STDGTI
reading cal file: gis2_ano_on_flf_180295.fits
reading inst file: GIS2_REGION256_OFF.4_regionmap.tmp
making an inst map...
multiply inst map...
reading att file: ./fa930428_1949.2350
making an exposure map...
Aspect RA/DEC/ROLL : 288.4410 4.9767 286.0825
Mean RA/DEC/ROLL : 288.4404 4.9487 286.0825
Pnt RA/DEC/ROLL : 288.4440 4.9990 286.0825
Image rebin factor : 1
Attitude Records : 6339
GTI intervals : 4
Total GTI (secs) : 6768.033
Max attitude excursion (arcsecs) : 5.000
0 Percent Complete: Total/live time: 0.0000000 0.0000000
10 Percent Complete: Total/live time: 1400.0001221 1400.0001221
20 Percent Complete: Total/live time: 1591.9881592 1591.9881592
30 Percent Complete: Total/live time: 2355.9858398 2355.9858398
40 Percent Complete: Total/live time: 2867.9843750 2867.9843750
50 Percent Complete: Total/live time: 4888.0000000 4888.0000000
60 Percent Complete: Total/live time: 4888.0000000 4888.0000000
70 Percent Complete: Total/live time: 4892.0000000 4892.0000000
80 Percent Complete: Total/live time: 5559.9980469 5559.9980469
90 Percent Complete: Total/live time: 6231.9960938 6231.9960938
100 Percent Complete: Total/live time: 6768.0332031 6768.0332031
Number of attitude steps used: 20
Number of attitude steps avail: 2525
Mean RA/DEC pixel offset: -12.8619 -3.4776
writing expo file: ad50006000g200470m.expo
closing attitude file...
closing data file...
-> Generating low and high energy images for ad50006000g200470m.evt
** XSELECT V1.3 **
!> Enter session name >[xsel] ad50006000g200470m
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS PHA_BINS
1 W50 EAST PH MEDIUM 28/04/93 19:50:32 0.68E+04 4255 1024
EXTRACTOR vers 2.0 11 Apr 1997.
Getting FITS WCS Keywords
Doing file: /data/data17/seq_proc/50006000.007/ad50006000g200470m.evt
Total Good Bad: Region Time Phase Cut
4255 4255 0 0 0 0
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
4255 4255 0 0 0 0
in 6768.03 seconds
Image has 4255 counts for 0.6287 counts/sec
EXTRACTOR vers 2.0 11 Apr 1997.
Getting FITS WCS Keywords
Doing file: /data/data17/seq_proc/50006000.007/ad50006000g200470m.evt
Total Good Bad: Region Time Phase Cut
4255 2034 0 0 0 2221
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
4255 2034 0 0 0 2221
in 6768.03 seconds
Image has 2034 counts for 0.3005 counts/sec
EXTRACTOR vers 2.0 11 Apr 1997.
Getting FITS WCS Keywords
Doing file: /data/data17/seq_proc/50006000.007/ad50006000g200470m.evt
Total Good Bad: Region Time Phase Cut
4255 2233 0 0 0 2022
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
4255 2233 0 0 0 2022
in 6768.03 seconds
Image has 2233 counts for 0.3299 counts/sec
Command not found; type ? for a command listing
!ad50006000g200470m:ASCA >
!ad50006000g200470m:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!ad50006000g200470m:ASCA > set datadir .
Setting data directory to /data/data17/seq_proc/50006000.007/
Setting mkf directory to /data/data17/seq_proc/50006000.007/
!ad50006000g200470m:ASCA > read events ad50006000g200470m.evt
Got new instrument: GIS2
Setting: IMAGE binning = 1
WMAP binning = 1
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 1023
Got the minimum time resolution of the read data: 0.50000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data17/seq_proc/50006000.007/
HK Directory is: /data/data17/seq_proc/50006000.007/
!ad50006000g200470m:ASCA-GIS2-PH > set image sky
!ad50006000g200470m:ASCA-GIS2-PH > filter region corner_point.reg
!ad50006000g200470m:ASCA-GIS2-PH > extract image
!ad50006000g200470m:ASCA-GIS2-PH > save image outfile=ad50006000g200470m.img
Wrote image to file ad50006000g200470m.img
!ad50006000g200470m:ASCA-GIS2-PH > filter pha_cut 0 170
!ad50006000g200470m:ASCA-GIS2-PH > extract image
!ad50006000g200470m:ASCA-GIS2-PH > save image outfile=ad50006000g200470m_lo.img
Wrote image to file ad50006000g200470m_lo.img
!ad50006000g200470m:ASCA-GIS2-PH > clear pha_cut
!ad50006000g200470m:ASCA-GIS2-PH > filter pha_cut 170 1024
Warning: your PI upper bound: 1024 is above the maximum value.
!ad50006000g200470m:ASCA-GIS2-PH > extract image
!ad50006000g200470m:ASCA-GIS2-PH > save image outfile=ad50006000g200470m_hi.img
Wrote image to file ad50006000g200470m_hi.img
!ad50006000g200470m:ASCA-GIS2-PH > exit save_session=no
-> Generating exposure map ad50006000g200570h.expo
ASCAEXPO_V0.9b
reading data file: ad50006000g200570h.evt
reading gti ext: STDGTI
reading cal file: gis2_ano_on_flf_180295.fits
reading inst file: GIS2_REGION256_OFF.4_regionmap.tmp
making an inst map...
multiply inst map...
reading att file: ./fa930428_1949.2350
making an exposure map...
Aspect RA/DEC/ROLL : 288.4410 4.9767 286.0833
Mean RA/DEC/ROLL : 288.4400 4.9467 286.0833
Pnt RA/DEC/ROLL : 288.4438 5.0046 286.0833
Image rebin factor : 1
Attitude Records : 6339
GTI intervals : 1
Total GTI (secs) : 1529.995
Max attitude excursion (arcsecs) : 5.000
0 Percent Complete: Total/live time: 0.0000000 0.0000000
10 Percent Complete: Total/live time: 312.9990234 312.9990234
20 Percent Complete: Total/live time: 323.9990540 323.9990540
30 Percent Complete: Total/live time: 1529.9953613 1529.9953613
100 Percent Complete: Total/live time: 1529.9953613 1529.9953613
Number of attitude steps used: 4
Number of attitude steps avail: 3076
Mean RA/DEC pixel offset: -10.5805 -3.4911
writing expo file: ad50006000g200570h.expo
closing attitude file...
closing data file...
-> Generating low and high energy images for ad50006000g200570h.evt
** XSELECT V1.3 **
!> Enter session name >[xsel] ad50006000g200570h
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS PHA_BINS
1 W50 EAST PH HIGH 28/04/93 22:52:30 0.15E+04 1004 1024
EXTRACTOR vers 2.0 11 Apr 1997.
Getting FITS WCS Keywords
Doing file: /data/data17/seq_proc/50006000.007/ad50006000g200570h.evt
Total Good Bad: Region Time Phase Cut
1004 1004 0 0 0 0
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
1004 1004 0 0 0 0
in 1530.00 seconds
Image has 1004 counts for 0.6562 counts/sec
EXTRACTOR vers 2.0 11 Apr 1997.
Getting FITS WCS Keywords
Doing file: /data/data17/seq_proc/50006000.007/ad50006000g200570h.evt
Total Good Bad: Region Time Phase Cut
1004 463 0 0 0 541
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
1004 463 0 0 0 541
in 1530.00 seconds
Image has 463 counts for 0.3026 counts/sec
EXTRACTOR vers 2.0 11 Apr 1997.
Getting FITS WCS Keywords
Doing file: /data/data17/seq_proc/50006000.007/ad50006000g200570h.evt
Total Good Bad: Region Time Phase Cut
1004 544 0 0 0 460
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
1004 544 0 0 0 460
in 1530.00 seconds
Image has 544 counts for 0.3556 counts/sec
Command not found; type ? for a command listing
!ad50006000g200570h:ASCA >
!ad50006000g200570h:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!ad50006000g200570h:ASCA > set datadir .
Setting data directory to /data/data17/seq_proc/50006000.007/
Setting mkf directory to /data/data17/seq_proc/50006000.007/
!ad50006000g200570h:ASCA > read events ad50006000g200570h.evt
Got new instrument: GIS2
Setting: IMAGE binning = 1
WMAP binning = 1
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 1023
Got the minimum time resolution of the read data: 0.62500E-01
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data17/seq_proc/50006000.007/
HK Directory is: /data/data17/seq_proc/50006000.007/
!ad50006000g200570h:ASCA-GIS2-PH > set image sky
!ad50006000g200570h:ASCA-GIS2-PH > filter region corner_point.reg
!ad50006000g200570h:ASCA-GIS2-PH > extract image
!ad50006000g200570h:ASCA-GIS2-PH > save image outfile=ad50006000g200570h.img
Wrote image to file ad50006000g200570h.img
!ad50006000g200570h:ASCA-GIS2-PH > filter pha_cut 0 170
!ad50006000g200570h:ASCA-GIS2-PH > extract image
!ad50006000g200570h:ASCA-GIS2-PH > save image outfile=ad50006000g200570h_lo.img
Wrote image to file ad50006000g200570h_lo.img
!ad50006000g200570h:ASCA-GIS2-PH > clear pha_cut
!ad50006000g200570h:ASCA-GIS2-PH > filter pha_cut 170 1024
Warning: your PI upper bound: 1024 is above the maximum value.
!ad50006000g200570h:ASCA-GIS2-PH > extract image
!ad50006000g200570h:ASCA-GIS2-PH > save image outfile=ad50006000g200570h_hi.img
Wrote image to file ad50006000g200570h_hi.img
!ad50006000g200570h:ASCA-GIS2-PH > exit save_session=no
-> Generating exposure map ad50006000g300170m.expo-ANNULUS(128.5,128.5,192,73) -ELLIPSE(217,95,21.56,25.92,169.216)-> gis3_ano_on_flf_180295.fits already present in current directory
ASCAEXPO_V0.9b
reading data file: ad50006000g300170m.evt
reading gti ext: STDGTI
reading cal file: gis3_ano_on_flf_180295.fits
reading inst file: GIS3_REGION256_OFF.4_regionmap.tmp
making an inst map...
multiply inst map...
reading att file: ./fa930427_2350.1950
making an exposure map...
Aspect RA/DEC/ROLL : 288.4410 4.9767 286.0798
Mean RA/DEC/ROLL : 288.4386 4.9741 286.0798
Pnt RA/DEC/ROLL : 288.2658 5.0514 286.0798
Image rebin factor : 1
Attitude Records : 61026
GTI intervals : 18
Total GTI (secs) : 11599.793
Max attitude excursion (arcsecs) : 5.000
0 Percent Complete: Total/live time: 0.0000000 0.0000000
10 Percent Complete: Total/live time: 1643.9914551 1643.9914551
20 Percent Complete: Total/live time: 2880.0000000 2880.0000000
30 Percent Complete: Total/live time: 3635.9975586 3635.9975586
40 Percent Complete: Total/live time: 5467.9912109 5467.9912109
50 Percent Complete: Total/live time: 6096.0229492 6096.0229492
60 Percent Complete: Total/live time: 7119.9780273 7119.9780273
70 Percent Complete: Total/live time: 9935.9785156 9935.9785156
80 Percent Complete: Total/live time: 9935.9785156 9935.9785156
90 Percent Complete: Total/live time: 10719.8964844 10719.8964844
100 Percent Complete: Total/live time: 11599.7919922 11599.7919922
Number of attitude steps used: 54
Number of attitude steps avail: 5867
Mean RA/DEC pixel offset: -0.2606 -2.5348
writing expo file: ad50006000g300170m.expo
closing attitude file...
closing data file...
-> Generating low and high energy images for ad50006000g300170m.evt
** XSELECT V1.3 **
!> Enter session name >[xsel] ad50006000g300170m
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS PHA_BINS
1 W50 EAST PH MEDIUM 27/04/93 23:50:48 0.12E+05 7421 1024
EXTRACTOR vers 2.0 11 Apr 1997.
Getting FITS WCS Keywords
Doing file: /data/data17/seq_proc/50006000.007/ad50006000g300170m.evt
Total Good Bad: Region Time Phase Cut
7421 7421 0 0 0 0
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
7421 7421 0 0 0 0
in 11599.79 seconds
Image has 7421 counts for 0.6398 counts/sec
EXTRACTOR vers 2.0 11 Apr 1997.
Getting FITS WCS Keywords
Doing file: /data/data17/seq_proc/50006000.007/ad50006000g300170m.evt
Total Good Bad: Region Time Phase Cut
7421 3700 0 0 0 3721
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
7421 3700 0 0 0 3721
in 11599.79 seconds
Image has 3700 counts for 0.3190 counts/sec
EXTRACTOR vers 2.0 11 Apr 1997.
Getting FITS WCS Keywords
Doing file: /data/data17/seq_proc/50006000.007/ad50006000g300170m.evt
Total Good Bad: Region Time Phase Cut
7421 3744 0 0 0 3677
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
7421 3744 0 0 0 3677
in 11599.79 seconds
Image has 3744 counts for 0.3228 counts/sec
Command not found; type ? for a command listing
!ad50006000g300170m:ASCA >
!ad50006000g300170m:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!ad50006000g300170m:ASCA > set datadir .
Setting data directory to /data/data17/seq_proc/50006000.007/
Setting mkf directory to /data/data17/seq_proc/50006000.007/
!ad50006000g300170m:ASCA > read events ad50006000g300170m.evt
Got new instrument: GIS3
Setting: IMAGE binning = 1
WMAP binning = 1
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 1023
Got the minimum time resolution of the read data: 0.50000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data17/seq_proc/50006000.007/
HK Directory is: /data/data17/seq_proc/50006000.007/
!ad50006000g300170m:ASCA-GIS3-PH > set image sky
!ad50006000g300170m:ASCA-GIS3-PH > filter region corner_point.reg
!ad50006000g300170m:ASCA-GIS3-PH > extract image
!ad50006000g300170m:ASCA-GIS3-PH > save image outfile=ad50006000g300170m.img
Wrote image to file ad50006000g300170m.img
!ad50006000g300170m:ASCA-GIS3-PH > filter pha_cut 0 170
!ad50006000g300170m:ASCA-GIS3-PH > extract image
!ad50006000g300170m:ASCA-GIS3-PH > save image outfile=ad50006000g300170m_lo.img
Wrote image to file ad50006000g300170m_lo.img
!ad50006000g300170m:ASCA-GIS3-PH > clear pha_cut
!ad50006000g300170m:ASCA-GIS3-PH > filter pha_cut 170 1024
Warning: your PI upper bound: 1024 is above the maximum value.
!ad50006000g300170m:ASCA-GIS3-PH > extract image
!ad50006000g300170m:ASCA-GIS3-PH > save image outfile=ad50006000g300170m_hi.img
Wrote image to file ad50006000g300170m_hi.img
!ad50006000g300170m:ASCA-GIS3-PH > exit save_session=no
-> Generating exposure map ad50006000g300270h.expo
ASCAEXPO_V0.9b
reading data file: ad50006000g300270h.evt
reading gti ext: STDGTI
reading cal file: gis3_ano_on_flf_180295.fits
reading inst file: GIS3_REGION256_OFF.4_regionmap.tmp
making an inst map...
multiply inst map...
reading att file: ./fa930427_2350.1950
making an exposure map...
Aspect RA/DEC/ROLL : 288.4410 4.9767 286.0797
Mean RA/DEC/ROLL : 288.4380 4.9762 286.0797
Pnt RA/DEC/ROLL : 288.4492 4.9757 286.0797
Image rebin factor : 1
Attitude Records : 61026
GTI intervals : 32
Total GTI (secs) : 17799.715
Max attitude excursion (arcsecs) : 5.000
0 Percent Complete: Total/live time: 0.0000000 0.0000000
10 Percent Complete: Total/live time: 2962.1303711 2962.1303711
20 Percent Complete: Total/live time: 4022.2299805 4022.2299805
30 Percent Complete: Total/live time: 6016.0922852 6016.0922852
40 Percent Complete: Total/live time: 7457.9345703 7457.9345703
50 Percent Complete: Total/live time: 9791.9267578 9791.9267578
60 Percent Complete: Total/live time: 10863.7392578 10863.7392578
70 Percent Complete: Total/live time: 12877.7333984 12877.7333984
80 Percent Complete: Total/live time: 16059.9394531 16059.9394531
90 Percent Complete: Total/live time: 16405.7207031 16405.7207031
100 Percent Complete: Total/live time: 17799.7207031 17799.7207031
Number of attitude steps used: 38
Number of attitude steps avail: 46683
Mean RA/DEC pixel offset: -0.0896 -1.4794
writing expo file: ad50006000g300270h.expo
closing attitude file...
closing data file...
-> Generating low and high energy images for ad50006000g300270h.evt
** XSELECT V1.3 **
!> Enter session name >[xsel] ad50006000g300270h
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS PHA_BINS
1 W50 EAST PH HIGH 28/04/93 03:44:46 0.18E+05 11260 1024
EXTRACTOR vers 2.0 11 Apr 1997.
Getting FITS WCS Keywords
Doing file: /data/data17/seq_proc/50006000.007/ad50006000g300270h.evt
Total Good Bad: Region Time Phase Cut
11260 11260 0 0 0 0
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
11260 11260 0 0 0 0
in 17799.72 seconds
Image has 11260 counts for 0.6326 counts/sec
EXTRACTOR vers 2.0 11 Apr 1997.
Getting FITS WCS Keywords
Doing file: /data/data17/seq_proc/50006000.007/ad50006000g300270h.evt
Total Good Bad: Region Time Phase Cut
11260 5544 0 0 0 5716
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
11260 5544 0 0 0 5716
in 17799.72 seconds
Image has 5544 counts for 0.3115 counts/sec
EXTRACTOR vers 2.0 11 Apr 1997.
Getting FITS WCS Keywords
Doing file: /data/data17/seq_proc/50006000.007/ad50006000g300270h.evt
Total Good Bad: Region Time Phase Cut
11260 5753 0 0 0 5507
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
11260 5753 0 0 0 5507
in 17799.72 seconds
Image has 5753 counts for 0.3232 counts/sec
Command not found; type ? for a command listing
!ad50006000g300270h:ASCA >
!ad50006000g300270h:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!ad50006000g300270h:ASCA > set datadir .
Setting data directory to /data/data17/seq_proc/50006000.007/
Setting mkf directory to /data/data17/seq_proc/50006000.007/
!ad50006000g300270h:ASCA > read events ad50006000g300270h.evt
Got new instrument: GIS3
Setting: IMAGE binning = 1
WMAP binning = 1
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 1023
Got the minimum time resolution of the read data: 0.62500E-01
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data17/seq_proc/50006000.007/
HK Directory is: /data/data17/seq_proc/50006000.007/
!ad50006000g300270h:ASCA-GIS3-PH > set image sky
!ad50006000g300270h:ASCA-GIS3-PH > filter region corner_point.reg
!ad50006000g300270h:ASCA-GIS3-PH > extract image
!ad50006000g300270h:ASCA-GIS3-PH > save image outfile=ad50006000g300270h.img
Wrote image to file ad50006000g300270h.img
!ad50006000g300270h:ASCA-GIS3-PH > filter pha_cut 0 170
!ad50006000g300270h:ASCA-GIS3-PH > extract image
!ad50006000g300270h:ASCA-GIS3-PH > save image outfile=ad50006000g300270h_lo.img
Wrote image to file ad50006000g300270h_lo.img
!ad50006000g300270h:ASCA-GIS3-PH > clear pha_cut
!ad50006000g300270h:ASCA-GIS3-PH > filter pha_cut 170 1024
Warning: your PI upper bound: 1024 is above the maximum value.
!ad50006000g300270h:ASCA-GIS3-PH > extract image
!ad50006000g300270h:ASCA-GIS3-PH > save image outfile=ad50006000g300270h_hi.img
Wrote image to file ad50006000g300270h_hi.img
!ad50006000g300270h:ASCA-GIS3-PH > exit save_session=no
-> Generating exposure map ad50006000g300470m.expo
ASCAEXPO_V0.9b
reading data file: ad50006000g300470m.evt
reading gti ext: STDGTI
reading cal file: gis3_ano_on_flf_180295.fits
reading inst file: GIS3_REGION256_OFF.4_regionmap.tmp
making an inst map...
multiply inst map...
reading att file: ./fa930428_1949.2350
making an exposure map...
Aspect RA/DEC/ROLL : 288.4410 4.9767 286.0822
Mean RA/DEC/ROLL : 288.4359 4.9730 286.0822
Pnt RA/DEC/ROLL : 288.4485 4.9745 286.0822
Image rebin factor : 1
Attitude Records : 6339
GTI intervals : 4
Total GTI (secs) : 6768.033
Max attitude excursion (arcsecs) : 5.000
0 Percent Complete: Total/live time: 0.0000000 0.0000000
10 Percent Complete: Total/live time: 1400.0001221 1400.0001221
20 Percent Complete: Total/live time: 1591.9881592 1591.9881592
30 Percent Complete: Total/live time: 2355.9858398 2355.9858398
40 Percent Complete: Total/live time: 2867.9843750 2867.9843750
50 Percent Complete: Total/live time: 4888.0000000 4888.0000000
60 Percent Complete: Total/live time: 4888.0000000 4888.0000000
70 Percent Complete: Total/live time: 4892.0000000 4892.0000000
80 Percent Complete: Total/live time: 5559.9980469 5559.9980469
90 Percent Complete: Total/live time: 6231.9960938 6231.9960938
100 Percent Complete: Total/live time: 6768.0332031 6768.0332031
Number of attitude steps used: 20
Number of attitude steps avail: 2525
Mean RA/DEC pixel offset: -1.3872 -2.3377
writing expo file: ad50006000g300470m.expo
closing attitude file...
closing data file...
-> Generating low and high energy images for ad50006000g300470m.evt
** XSELECT V1.3 **
!> Enter session name >[xsel] ad50006000g300470m
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS PHA_BINS
1 W50 EAST PH MEDIUM 28/04/93 19:50:32 0.68E+04 4275 1024
EXTRACTOR vers 2.0 11 Apr 1997.
Getting FITS WCS Keywords
Doing file: /data/data17/seq_proc/50006000.007/ad50006000g300470m.evt
Total Good Bad: Region Time Phase Cut
4275 4275 0 0 0 0
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
4275 4275 0 0 0 0
in 6768.03 seconds
Image has 4275 counts for 0.6316 counts/sec
EXTRACTOR vers 2.0 11 Apr 1997.
Getting FITS WCS Keywords
Doing file: /data/data17/seq_proc/50006000.007/ad50006000g300470m.evt
Total Good Bad: Region Time Phase Cut
4275 2129 0 0 0 2146
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
4275 2129 0 0 0 2146
in 6768.03 seconds
Image has 2129 counts for 0.3146 counts/sec
EXTRACTOR vers 2.0 11 Apr 1997.
Getting FITS WCS Keywords
Doing file: /data/data17/seq_proc/50006000.007/ad50006000g300470m.evt
Total Good Bad: Region Time Phase Cut
4275 2158 0 0 0 2117
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
4275 2158 0 0 0 2117
in 6768.03 seconds
Image has 2158 counts for 0.3189 counts/sec
Command not found; type ? for a command listing
!ad50006000g300470m:ASCA >
!ad50006000g300470m:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!ad50006000g300470m:ASCA > set datadir .
Setting data directory to /data/data17/seq_proc/50006000.007/
Setting mkf directory to /data/data17/seq_proc/50006000.007/
!ad50006000g300470m:ASCA > read events ad50006000g300470m.evt
Got new instrument: GIS3
Setting: IMAGE binning = 1
WMAP binning = 1
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 1023
Got the minimum time resolution of the read data: 0.50000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data17/seq_proc/50006000.007/
HK Directory is: /data/data17/seq_proc/50006000.007/
!ad50006000g300470m:ASCA-GIS3-PH > set image sky
!ad50006000g300470m:ASCA-GIS3-PH > filter region corner_point.reg
!ad50006000g300470m:ASCA-GIS3-PH > extract image
!ad50006000g300470m:ASCA-GIS3-PH > save image outfile=ad50006000g300470m.img
Wrote image to file ad50006000g300470m.img
!ad50006000g300470m:ASCA-GIS3-PH > filter pha_cut 0 170
!ad50006000g300470m:ASCA-GIS3-PH > extract image
!ad50006000g300470m:ASCA-GIS3-PH > save image outfile=ad50006000g300470m_lo.img
Wrote image to file ad50006000g300470m_lo.img
!ad50006000g300470m:ASCA-GIS3-PH > clear pha_cut
!ad50006000g300470m:ASCA-GIS3-PH > filter pha_cut 170 1024
Warning: your PI upper bound: 1024 is above the maximum value.
!ad50006000g300470m:ASCA-GIS3-PH > extract image
!ad50006000g300470m:ASCA-GIS3-PH > save image outfile=ad50006000g300470m_hi.img
Wrote image to file ad50006000g300470m_hi.img
!ad50006000g300470m:ASCA-GIS3-PH > exit save_session=no
-> Generating exposure map ad50006000g300570h.expo
ASCAEXPO_V0.9b
reading data file: ad50006000g300570h.evt
reading gti ext: STDGTI
reading cal file: gis3_ano_on_flf_180295.fits
reading inst file: GIS3_REGION256_OFF.4_regionmap.tmp
making an inst map...
multiply inst map...
reading att file: ./fa930428_1949.2350
making an exposure map...
Aspect RA/DEC/ROLL : 288.4410 4.9767 286.0830
Mean RA/DEC/ROLL : 288.4355 4.9711 286.0830
Pnt RA/DEC/ROLL : 288.4483 4.9801 286.0830
Image rebin factor : 1
Attitude Records : 6339
GTI intervals : 1
Total GTI (secs) : 1529.995
Max attitude excursion (arcsecs) : 5.000
0 Percent Complete: Total/live time: 0.0000000 0.0000000
10 Percent Complete: Total/live time: 312.9990234 312.9990234
20 Percent Complete: Total/live time: 323.9990540 323.9990540
30 Percent Complete: Total/live time: 1529.9953613 1529.9953613
100 Percent Complete: Total/live time: 1529.9953613 1529.9953613
Number of attitude steps used: 4
Number of attitude steps avail: 3076
Mean RA/DEC pixel offset: -1.5215 -2.5911
writing expo file: ad50006000g300570h.expo
closing attitude file...
closing data file...
-> Generating low and high energy images for ad50006000g300570h.evt
** XSELECT V1.3 **
!> Enter session name >[xsel] ad50006000g300570h
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS PHA_BINS
1 W50 EAST PH HIGH 28/04/93 22:52:30 0.15E+04 1006 1024
EXTRACTOR vers 2.0 11 Apr 1997.
Getting FITS WCS Keywords
Doing file: /data/data17/seq_proc/50006000.007/ad50006000g300570h.evt
Total Good Bad: Region Time Phase Cut
1006 1006 0 0 0 0
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
1006 1006 0 0 0 0
in 1530.00 seconds
Image has 1006 counts for 0.6575 counts/sec
EXTRACTOR vers 2.0 11 Apr 1997.
Getting FITS WCS Keywords
Doing file: /data/data17/seq_proc/50006000.007/ad50006000g300570h.evt
Total Good Bad: Region Time Phase Cut
1006 484 0 0 0 522
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
1006 484 0 0 0 522
in 1530.00 seconds
Image has 484 counts for 0.3163 counts/sec
EXTRACTOR vers 2.0 11 Apr 1997.
Getting FITS WCS Keywords
Doing file: /data/data17/seq_proc/50006000.007/ad50006000g300570h.evt
Total Good Bad: Region Time Phase Cut
1006 525 0 0 0 481
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
1006 525 0 0 0 481
in 1530.00 seconds
Image has 525 counts for 0.3431 counts/sec
Command not found; type ? for a command listing
!ad50006000g300570h:ASCA >
!ad50006000g300570h:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!ad50006000g300570h:ASCA > set datadir .
Setting data directory to /data/data17/seq_proc/50006000.007/
Setting mkf directory to /data/data17/seq_proc/50006000.007/
!ad50006000g300570h:ASCA > read events ad50006000g300570h.evt
Got new instrument: GIS3
Setting: IMAGE binning = 1
WMAP binning = 1
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 1023
Got the minimum time resolution of the read data: 0.62500E-01
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data17/seq_proc/50006000.007/
HK Directory is: /data/data17/seq_proc/50006000.007/
!ad50006000g300570h:ASCA-GIS3-PH > set image sky
!ad50006000g300570h:ASCA-GIS3-PH > filter region corner_point.reg
!ad50006000g300570h:ASCA-GIS3-PH > extract image
!ad50006000g300570h:ASCA-GIS3-PH > save image outfile=ad50006000g300570h.img
Wrote image to file ad50006000g300570h.img
!ad50006000g300570h:ASCA-GIS3-PH > filter pha_cut 0 170
!ad50006000g300570h:ASCA-GIS3-PH > extract image
!ad50006000g300570h:ASCA-GIS3-PH > save image outfile=ad50006000g300570h_lo.img
Wrote image to file ad50006000g300570h_lo.img
!ad50006000g300570h:ASCA-GIS3-PH > clear pha_cut
!ad50006000g300570h:ASCA-GIS3-PH > filter pha_cut 170 1024
Warning: your PI upper bound: 1024 is above the maximum value.
!ad50006000g300570h:ASCA-GIS3-PH > extract image
!ad50006000g300570h:ASCA-GIS3-PH > save image outfile=ad50006000g300570h_hi.img
Wrote image to file ad50006000g300570h_hi.img
!ad50006000g300570h:ASCA-GIS3-PH > exit save_session=no
-> Generating exposure map ad50006000s000102h.expo
ASCAEXPO_V0.9b
reading data file: ad50006000s000102h.evt
reading gti ext: STDGTI
reading hp ext: HOT_PIXELS
reading cal file: s0_teldef_ascalin.fits
making an inst map...
SIS AREA DISC ENABL OFF
CHIP: 0 1 2 3
CCD POWER ON/OFF: ON ON ON ON
AREA DISC IN/OUT: OUT IN OUT OUT
AREA DISC H START: 6 119 6 6
AREA DISC H STOP: 425 230 425 425
AREA DISC V START: 2 140 2 2
AREA DISC V STOP: 422 220 422 422
reading att file: ./fa930427_2350.1950
making an exposure map...
Aspect RA/DEC/ROLL : 288.4410 4.9767 286.0786
Mean RA/DEC/ROLL : 288.4254 4.9599 286.0786
Pnt RA/DEC/ROLL : 288.4600 4.9926 286.0786
Image rebin factor : 4
Attitude Records : 61026
Hot Pixels : 437
GTI intervals : 35
Total GTI (secs) : 15568.818
Max attitude excursion (arcsecs) : 5.000
0 Percent Complete: Total/live time: 0.0000000 0.0000000
10 Percent Complete: Total/live time: 3081.9482422 3081.9482422
20 Percent Complete: Total/live time: 3316.9475098 3316.9475098
30 Percent Complete: Total/live time: 4913.7617188 4913.7617188
40 Percent Complete: Total/live time: 6536.2714844 6536.2714844
50 Percent Complete: Total/live time: 7965.4243164 7965.4243164
60 Percent Complete: Total/live time: 9510.4433594 9510.4433594
70 Percent Complete: Total/live time: 11131.1328125 11131.1328125
80 Percent Complete: Total/live time: 14025.1015625 14025.1015625
90 Percent Complete: Total/live time: 14358.8818359 14358.8818359
100 Percent Complete: Total/live time: 15568.8173828 15568.8173828
Number of attitude steps used: 35
Number of attitude steps avail: 41915
Mean RA/DEC pixel offset: -55.1904 -86.4174
writing expo file: ad50006000s000102h.expo
closing attitude file...
closing data file...
-> Generating low and high energy images for ad50006000s000102h.evt
** XSELECT V1.3 **
!> Enter session name >[xsel] ad50006000s000102h
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS S0CCDPOW
1 W50 EAST BRIGHT HIGH 28/04/93 03:44:28 0.16E+05 10231 1111
EXTRACTOR vers 2.0 11 Apr 1997.
Getting FITS WCS Keywords
Doing file: /data/data17/seq_proc/50006000.007/ad50006000s000102h.evt
Total Good Bad: Region Time Phase Cut
10231 10231 0 0 0 0
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
10231 10231 0 0 0 0
in 15568.82 seconds
Image has 10231 counts for 0.6571 counts/sec
EXTRACTOR vers 2.0 11 Apr 1997.
Getting FITS WCS Keywords
Doing file: /data/data17/seq_proc/50006000.007/ad50006000s000102h.evt
Total Good Bad: Region Time Phase Cut
10231 5702 0 0 0 4529
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
10231 5702 0 0 0 4529
in 15568.82 seconds
Image has 5702 counts for 0.3662 counts/sec
EXTRACTOR vers 2.0 11 Apr 1997.
Getting FITS WCS Keywords
Doing file: /data/data17/seq_proc/50006000.007/ad50006000s000102h.evt
Total Good Bad: Region Time Phase Cut
10231 4535 0 0 0 5696
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
10231 4535 0 0 0 5696
in 15568.82 seconds
Image has 4535 counts for 0.2913 counts/sec
Command not found; type ? for a command listing
!ad50006000s000102h:ASCA >
!ad50006000s000102h:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!ad50006000s000102h:ASCA > set datadir .
Setting data directory to /data/data17/seq_proc/50006000.007/
Setting mkf directory to /data/data17/seq_proc/50006000.007/
!ad50006000s000102h:ASCA > read events ad50006000s000102h.evt
Got new instrument: SIS0
Setting: IMAGE binning = 4
WMAP binning = 8
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 2047
Got the minimum time resolution of the read data: 16.000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data17/seq_proc/50006000.007/
HK Directory is: /data/data17/seq_proc/50006000.007/
!ad50006000s000102h:ASCA-SIS0-BRIGHT > set image sky
!ad50006000s000102h:ASCA-SIS0-BRIGHT > filter region corner_point.reg
!ad50006000s000102h:ASCA-SIS0-BRIGHT > extract image
!ad50006000s000102h:ASCA-SIS0-BRIGHT > save image outfile=ad50006000s000102h.img
Wrote image to file ad50006000s000102h.img
!ad50006000s000102h:ASCA-SIS0-BRIGHT > filter pha_cut 0 547
!ad50006000s000102h:ASCA-SIS0-BRIGHT > extract image
!ad50006000s000102h:ASCA-SIS0-BRIGHT > save image outfile=ad50006000s000102h_lo.img
Wrote image to file ad50006000s000102h_lo.img
!ad50006000s000102h:ASCA-SIS0-BRIGHT > clear pha_cut
!ad50006000s000102h:ASCA-SIS0-BRIGHT > filter pha_cut 547 2048
Warning: your PI upper bound: 2048 is above the maximum value.
!ad50006000s000102h:ASCA-SIS0-BRIGHT > extract image
!ad50006000s000102h:ASCA-SIS0-BRIGHT > save image outfile=ad50006000s000102h_hi.img
Wrote image to file ad50006000s000102h_hi.img
!ad50006000s000102h:ASCA-SIS0-BRIGHT > exit save_session=no
-> Generating exposure map ad50006000s000202m.expo
ASCAEXPO_V0.9b
reading data file: ad50006000s000202m.evt
reading gti ext: STDGTI
reading hp ext: HOT_PIXELS
reading cal file: s0_teldef_ascalin.fits
making an inst map...
SIS AREA DISC ENABL OFF
CHIP: 0 1 2 3
CCD POWER ON/OFF: ON ON ON ON
AREA DISC IN/OUT: OUT IN OUT OUT
AREA DISC H START: 6 119 6 6
AREA DISC H STOP: 425 230 425 425
AREA DISC V START: 2 140 2 2
AREA DISC V STOP: 422 220 422 422
reading att file: ./fa930427_2350.1950
making an exposure map...
Aspect RA/DEC/ROLL : 288.4410 4.9767 286.0788
Mean RA/DEC/ROLL : 288.4267 4.9578 286.0788
Pnt RA/DEC/ROLL : 288.2806 5.0667 286.0788
Image rebin factor : 4
Attitude Records : 61026
Hot Pixels : 387
GTI intervals : 22
Total GTI (secs) : 11070.420
Max attitude excursion (arcsecs) : 5.000
0 Percent Complete: Total/live time: 0.0000000 0.0000000
10 Percent Complete: Total/live time: 1483.9912109 1483.9912109
20 Percent Complete: Total/live time: 2719.9997559 2719.9997559
30 Percent Complete: Total/live time: 3459.9738770 3459.9738770
40 Percent Complete: Total/live time: 5195.9677734 5195.9677734
50 Percent Complete: Total/live time: 5695.9995117 5695.9995117
60 Percent Complete: Total/live time: 8576.0000000 8576.0000000
70 Percent Complete: Total/live time: 8576.0000000 8576.0000000
80 Percent Complete: Total/live time: 9536.0878906 9536.0878906
90 Percent Complete: Total/live time: 10557.8261719 10557.8261719
100 Percent Complete: Total/live time: 11070.4208984 11070.4208984
Number of attitude steps used: 54
Number of attitude steps avail: 10897
Mean RA/DEC pixel offset: -55.7758 -97.5514
writing expo file: ad50006000s000202m.expo
closing attitude file...
closing data file...
-> Generating low and high energy images for ad50006000s000202m.evt
** XSELECT V1.3 **
!> Enter session name >[xsel] ad50006000s000202m
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS S0CCDPOW
1 W50 EAST BRIGHT MEDIUM 27/04/93 23:50:32 0.11E+05 7322 1111
EXTRACTOR vers 2.0 11 Apr 1997.
Getting FITS WCS Keywords
Doing file: /data/data17/seq_proc/50006000.007/ad50006000s000202m.evt
Total Good Bad: Region Time Phase Cut
7322 7322 0 0 0 0
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
7322 7322 0 0 0 0
in 11070.42 seconds
Image has 7322 counts for 0.6614 counts/sec
EXTRACTOR vers 2.0 11 Apr 1997.
Getting FITS WCS Keywords
Doing file: /data/data17/seq_proc/50006000.007/ad50006000s000202m.evt
Total Good Bad: Region Time Phase Cut
7322 4165 0 0 0 3157
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
7322 4165 0 0 0 3157
in 11070.42 seconds
Image has 4165 counts for 0.3762 counts/sec
EXTRACTOR vers 2.0 11 Apr 1997.
Getting FITS WCS Keywords
Doing file: /data/data17/seq_proc/50006000.007/ad50006000s000202m.evt
Total Good Bad: Region Time Phase Cut
7322 3163 0 0 0 4159
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
7322 3163 0 0 0 4159
in 11070.42 seconds
Image has 3163 counts for 0.2857 counts/sec
Command not found; type ? for a command listing
!ad50006000s000202m:ASCA >
!ad50006000s000202m:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!ad50006000s000202m:ASCA > set datadir .
Setting data directory to /data/data17/seq_proc/50006000.007/
Setting mkf directory to /data/data17/seq_proc/50006000.007/
!ad50006000s000202m:ASCA > read events ad50006000s000202m.evt
Got new instrument: SIS0
Setting: IMAGE binning = 4
WMAP binning = 8
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 2047
Got the minimum time resolution of the read data: 16.000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data17/seq_proc/50006000.007/
HK Directory is: /data/data17/seq_proc/50006000.007/
!ad50006000s000202m:ASCA-SIS0-BRIGHT > set image sky
!ad50006000s000202m:ASCA-SIS0-BRIGHT > filter region corner_point.reg
!ad50006000s000202m:ASCA-SIS0-BRIGHT > extract image
!ad50006000s000202m:ASCA-SIS0-BRIGHT > save image outfile=ad50006000s000202m.img
Wrote image to file ad50006000s000202m.img
!ad50006000s000202m:ASCA-SIS0-BRIGHT > filter pha_cut 0 547
!ad50006000s000202m:ASCA-SIS0-BRIGHT > extract image
!ad50006000s000202m:ASCA-SIS0-BRIGHT > save image outfile=ad50006000s000202m_lo.img
Wrote image to file ad50006000s000202m_lo.img
!ad50006000s000202m:ASCA-SIS0-BRIGHT > clear pha_cut
!ad50006000s000202m:ASCA-SIS0-BRIGHT > filter pha_cut 547 2048
Warning: your PI upper bound: 2048 is above the maximum value.
!ad50006000s000202m:ASCA-SIS0-BRIGHT > extract image
!ad50006000s000202m:ASCA-SIS0-BRIGHT > save image outfile=ad50006000s000202m_hi.img
Wrote image to file ad50006000s000202m_hi.img
!ad50006000s000202m:ASCA-SIS0-BRIGHT > exit save_session=no
-> Generating exposure map ad50006000s000302h.expo
ASCAEXPO_V0.9b
reading data file: ad50006000s000302h.evt
reading gti ext: STDGTI
reading hp ext: HOT_PIXELS
reading cal file: s0_teldef_ascalin.fits
making an inst map...
SIS AREA DISC ENABL OFF
CHIP: 0 1 2 3
CCD POWER ON/OFF: ON OFF ON ON
AREA DISC IN/OUT: OUT IN OUT OUT
AREA DISC H START: 6 119 6 6
AREA DISC H STOP: 425 230 425 425
AREA DISC V START: 2 140 2 2
AREA DISC V STOP: 422 220 422 422
reading att file: ./fa930427_2350.1950
making an exposure map...
Aspect RA/DEC/ROLL : 288.4410 4.9767 286.0771
Mean RA/DEC/ROLL : 288.4257 4.9606 286.0771
Pnt RA/DEC/ROLL : 288.4567 4.9918 286.0771
Image rebin factor : 4
Attitude Records : 61026
Hot Pixels : 187
GTI intervals : 6
Total GTI (secs) : 1939.593
Max attitude excursion (arcsecs) : 5.000
0 Percent Complete: Total/live time: 0.0000000 0.0000000
10 Percent Complete: Total/live time: 698.6287231 698.6287231
20 Percent Complete: Total/live time: 698.6287231 698.6287231
30 Percent Complete: Total/live time: 925.7990723 925.7990723
40 Percent Complete: Total/live time: 925.7990723 925.7990723
50 Percent Complete: Total/live time: 1939.5935059 1939.5935059
100 Percent Complete: Total/live time: 1939.5935059 1939.5935059
Number of attitude steps used: 4
Number of attitude steps avail: 4208
Mean RA/DEC pixel offset: -38.7993 -64.9917
writing expo file: ad50006000s000302h.expo
closing attitude file...
closing data file...
-> Generating low and high energy images for ad50006000s000302h.evt
** XSELECT V1.3 **
!> Enter session name >[xsel] ad50006000s000302h
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS S0CCDPOW
1 W50 EAST BRIGHT HIGH 28/04/93 14:34:00 0.19E+04 1341 1011
EXTRACTOR vers 2.0 11 Apr 1997.
Getting FITS WCS Keywords
Doing file: /data/data17/seq_proc/50006000.007/ad50006000s000302h.evt
Total Good Bad: Region Time Phase Cut
1341 1341 0 0 0 0
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
1341 1341 0 0 0 0
in 1939.59 seconds
Image has 1341 counts for 0.6914 counts/sec
EXTRACTOR vers 2.0 11 Apr 1997.
Getting FITS WCS Keywords
Doing file: /data/data17/seq_proc/50006000.007/ad50006000s000302h.evt
Total Good Bad: Region Time Phase Cut
1341 761 0 0 0 580
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
1341 761 0 0 0 580
in 1939.59 seconds
Image has 761 counts for 0.3924 counts/sec
EXTRACTOR vers 2.0 11 Apr 1997.
Getting FITS WCS Keywords
Doing file: /data/data17/seq_proc/50006000.007/ad50006000s000302h.evt
Total Good Bad: Region Time Phase Cut
1341 581 0 0 0 760
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
1341 581 0 0 0 760
in 1939.59 seconds
Image has 581 counts for 0.2995 counts/sec
Command not found; type ? for a command listing
!ad50006000s000302h:ASCA >
!ad50006000s000302h:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!ad50006000s000302h:ASCA > set datadir .
Setting data directory to /data/data17/seq_proc/50006000.007/
Setting mkf directory to /data/data17/seq_proc/50006000.007/
!ad50006000s000302h:ASCA > read events ad50006000s000302h.evt
Got new instrument: SIS0
Setting: IMAGE binning = 4
WMAP binning = 8
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 2047
Got the minimum time resolution of the read data: 16.000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data17/seq_proc/50006000.007/
HK Directory is: /data/data17/seq_proc/50006000.007/
!ad50006000s000302h:ASCA-SIS0-BRIGHT > set image sky
!ad50006000s000302h:ASCA-SIS0-BRIGHT > filter region corner_point.reg
!ad50006000s000302h:ASCA-SIS0-BRIGHT > extract image
!ad50006000s000302h:ASCA-SIS0-BRIGHT > save image outfile=ad50006000s000302h.img
Wrote image to file ad50006000s000302h.img
!ad50006000s000302h:ASCA-SIS0-BRIGHT > filter pha_cut 0 547
!ad50006000s000302h:ASCA-SIS0-BRIGHT > extract image
!ad50006000s000302h:ASCA-SIS0-BRIGHT > save image outfile=ad50006000s000302h_lo.img
Wrote image to file ad50006000s000302h_lo.img
!ad50006000s000302h:ASCA-SIS0-BRIGHT > clear pha_cut
!ad50006000s000302h:ASCA-SIS0-BRIGHT > filter pha_cut 547 2048
Warning: your PI upper bound: 2048 is above the maximum value.
!ad50006000s000302h:ASCA-SIS0-BRIGHT > extract image
!ad50006000s000302h:ASCA-SIS0-BRIGHT > save image outfile=ad50006000s000302h_hi.img
Wrote image to file ad50006000s000302h_hi.img
!ad50006000s000302h:ASCA-SIS0-BRIGHT > exit save_session=no
-> Generating exposure map ad50006000s000502m.expo
ASCAEXPO_V0.9b
reading data file: ad50006000s000502m.evt
reading gti ext: STDGTI
reading hp ext: HOT_PIXELS
reading cal file: s0_teldef_ascalin.fits
making an inst map...
SIS AREA DISC ENABL OFF
CHIP: 0 1 2 3
CCD POWER ON/OFF: ON ON ON ON
AREA DISC IN/OUT: OUT IN OUT OUT
AREA DISC H START: 6 119 6 6
AREA DISC H STOP: 425 230 425 425
AREA DISC V START: 2 140 2 2
AREA DISC V STOP: 422 220 422 422
reading att file: ./fa930428_1949.2350
making an exposure map...
Aspect RA/DEC/ROLL : 288.4410 4.9767 286.0807
Mean RA/DEC/ROLL : 288.4236 4.9576 286.0807
Pnt RA/DEC/ROLL : 288.4611 4.9910 286.0807
Image rebin factor : 4
Attitude Records : 6339
Hot Pixels : 266
GTI intervals : 13
Total GTI (secs) : 5512.037
Max attitude excursion (arcsecs) : 5.000
0 Percent Complete: Total/live time: 0.0000000 0.0000000
10 Percent Complete: Total/live time: 1152.0000000 1152.0000000
20 Percent Complete: Total/live time: 1667.9869385 1667.9869385
30 Percent Complete: Total/live time: 1915.9859619 1915.9859619
40 Percent Complete: Total/live time: 2331.9846191 2331.9846191
50 Percent Complete: Total/live time: 4000.0002441 4000.0002441
60 Percent Complete: Total/live time: 4000.0002441 4000.0002441
70 Percent Complete: Total/live time: 4003.9716797 4003.9716797
80 Percent Complete: Total/live time: 4647.9697266 4647.9697266
90 Percent Complete: Total/live time: 5115.9682617 5115.9682617
100 Percent Complete: Total/live time: 5512.0375977 5512.0375977
Number of attitude steps used: 19
Number of attitude steps avail: 2478
Mean RA/DEC pixel offset: -65.6730 -93.2577
writing expo file: ad50006000s000502m.expo
closing attitude file...
closing data file...
-> Generating low and high energy images for ad50006000s000502m.evt
** XSELECT V1.3 **
!> Enter session name >[xsel] ad50006000s000502m
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS S0CCDPOW
1 W50 EAST BRIGHT MEDIUM 28/04/93 19:50:16 0.55E+04 3663 1111
EXTRACTOR vers 2.0 11 Apr 1997.
Getting FITS WCS Keywords
Doing file: /data/data17/seq_proc/50006000.007/ad50006000s000502m.evt
Total Good Bad: Region Time Phase Cut
3663 3663 0 0 0 0
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
3663 3663 0 0 0 0
in 5512.04 seconds
Image has 3663 counts for 0.6645 counts/sec
EXTRACTOR vers 2.0 11 Apr 1997.
Getting FITS WCS Keywords
Doing file: /data/data17/seq_proc/50006000.007/ad50006000s000502m.evt
Total Good Bad: Region Time Phase Cut
3663 2189 0 0 0 1474
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
3663 2189 0 0 0 1474
in 5512.04 seconds
Image has 2189 counts for 0.3971 counts/sec
EXTRACTOR vers 2.0 11 Apr 1997.
Getting FITS WCS Keywords
Doing file: /data/data17/seq_proc/50006000.007/ad50006000s000502m.evt
Total Good Bad: Region Time Phase Cut
3663 1478 0 0 0 2185
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
3663 1478 0 0 0 2185
in 5512.04 seconds
Image has 1478 counts for 0.2681 counts/sec
Command not found; type ? for a command listing
!ad50006000s000502m:ASCA >
!ad50006000s000502m:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!ad50006000s000502m:ASCA > set datadir .
Setting data directory to /data/data17/seq_proc/50006000.007/
Setting mkf directory to /data/data17/seq_proc/50006000.007/
!ad50006000s000502m:ASCA > read events ad50006000s000502m.evt
Got new instrument: SIS0
Setting: IMAGE binning = 4
WMAP binning = 8
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 2047
Got the minimum time resolution of the read data: 16.000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data17/seq_proc/50006000.007/
HK Directory is: /data/data17/seq_proc/50006000.007/
!ad50006000s000502m:ASCA-SIS0-BRIGHT > set image sky
!ad50006000s000502m:ASCA-SIS0-BRIGHT > filter region corner_point.reg
!ad50006000s000502m:ASCA-SIS0-BRIGHT > extract image
!ad50006000s000502m:ASCA-SIS0-BRIGHT > save image outfile=ad50006000s000502m.img
Wrote image to file ad50006000s000502m.img
!ad50006000s000502m:ASCA-SIS0-BRIGHT > filter pha_cut 0 547
!ad50006000s000502m:ASCA-SIS0-BRIGHT > extract image
!ad50006000s000502m:ASCA-SIS0-BRIGHT > save image outfile=ad50006000s000502m_lo.img
Wrote image to file ad50006000s000502m_lo.img
!ad50006000s000502m:ASCA-SIS0-BRIGHT > clear pha_cut
!ad50006000s000502m:ASCA-SIS0-BRIGHT > filter pha_cut 547 2048
Warning: your PI upper bound: 2048 is above the maximum value.
!ad50006000s000502m:ASCA-SIS0-BRIGHT > extract image
!ad50006000s000502m:ASCA-SIS0-BRIGHT > save image outfile=ad50006000s000502m_hi.img
Wrote image to file ad50006000s000502m_hi.img
!ad50006000s000502m:ASCA-SIS0-BRIGHT > exit save_session=no
-> Generating exposure map ad50006000s000602h.expo
ASCAEXPO_V0.9b
reading data file: ad50006000s000602h.evt
reading gti ext: STDGTI
reading hp ext: HOT_PIXELS
reading cal file: s0_teldef_ascalin.fits
making an inst map...
SIS AREA DISC ENABL OFF
CHIP: 0 1 2 3
CCD POWER ON/OFF: ON ON ON ON
AREA DISC IN/OUT: OUT IN OUT OUT
AREA DISC H START: 6 119 6 6
AREA DISC H STOP: 425 230 425 425
AREA DISC V START: 2 140 2 2
AREA DISC V STOP: 422 220 422 422
reading att file: ./fa930428_1949.2350
making an exposure map...
Aspect RA/DEC/ROLL : 288.4410 4.9767 286.0819
Mean RA/DEC/ROLL : 288.4229 4.9547 286.0819
Pnt RA/DEC/ROLL : 288.4607 4.9965 286.0819
Image rebin factor : 4
Attitude Records : 6339
Hot Pixels : 184
GTI intervals : 2
Total GTI (secs) : 1453.932
Max attitude excursion (arcsecs) : 5.000
0 Percent Complete: Total/live time: 0.0000000 0.0000000
10 Percent Complete: Total/live time: 294.9665527 294.9665527
20 Percent Complete: Total/live time: 305.9665833 305.9665833
30 Percent Complete: Total/live time: 1453.9317627 1453.9317627
100 Percent Complete: Total/live time: 1453.9317627 1453.9317627
Number of attitude steps used: 4
Number of attitude steps avail: 3034
Mean RA/DEC pixel offset: -55.8510 -80.2697
writing expo file: ad50006000s000602h.expo
closing attitude file...
closing data file...
-> Generating low and high energy images for ad50006000s000602h.evt
** XSELECT V1.3 **
!> Enter session name >[xsel] ad50006000s000602h
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS S0CCDPOW
1 W50 EAST BRIGHT HIGH 28/04/93 22:52:12 0.15E+04 976 1111
EXTRACTOR vers 2.0 11 Apr 1997.
Getting FITS WCS Keywords
Doing file: /data/data17/seq_proc/50006000.007/ad50006000s000602h.evt
Total Good Bad: Region Time Phase Cut
976 976 0 0 0 0
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
976 976 0 0 0 0
in 1453.93 seconds
Image has 976 counts for 0.6713 counts/sec
EXTRACTOR vers 2.0 11 Apr 1997.
Getting FITS WCS Keywords
Doing file: /data/data17/seq_proc/50006000.007/ad50006000s000602h.evt
Total Good Bad: Region Time Phase Cut
976 580 0 0 0 396
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
976 580 0 0 0 396
in 1453.93 seconds
Image has 580 counts for 0.3989 counts/sec
EXTRACTOR vers 2.0 11 Apr 1997.
Getting FITS WCS Keywords
Doing file: /data/data17/seq_proc/50006000.007/ad50006000s000602h.evt
Total Good Bad: Region Time Phase Cut
976 396 0 0 0 580
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
976 396 0 0 0 580
in 1453.93 seconds
Image has 396 counts for 0.2724 counts/sec
Command not found; type ? for a command listing
!ad50006000s000602h:ASCA >
!ad50006000s000602h:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!ad50006000s000602h:ASCA > set datadir .
Setting data directory to /data/data17/seq_proc/50006000.007/
Setting mkf directory to /data/data17/seq_proc/50006000.007/
!ad50006000s000602h:ASCA > read events ad50006000s000602h.evt
Got new instrument: SIS0
Setting: IMAGE binning = 4
WMAP binning = 8
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 2047
Got the minimum time resolution of the read data: 16.000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data17/seq_proc/50006000.007/
HK Directory is: /data/data17/seq_proc/50006000.007/
!ad50006000s000602h:ASCA-SIS0-BRIGHT > set image sky
!ad50006000s000602h:ASCA-SIS0-BRIGHT > filter region corner_point.reg
!ad50006000s000602h:ASCA-SIS0-BRIGHT > extract image
!ad50006000s000602h:ASCA-SIS0-BRIGHT > save image outfile=ad50006000s000602h.img
Wrote image to file ad50006000s000602h.img
!ad50006000s000602h:ASCA-SIS0-BRIGHT > filter pha_cut 0 547
!ad50006000s000602h:ASCA-SIS0-BRIGHT > extract image
!ad50006000s000602h:ASCA-SIS0-BRIGHT > save image outfile=ad50006000s000602h_lo.img
Wrote image to file ad50006000s000602h_lo.img
!ad50006000s000602h:ASCA-SIS0-BRIGHT > clear pha_cut
!ad50006000s000602h:ASCA-SIS0-BRIGHT > filter pha_cut 547 2048
Warning: your PI upper bound: 2048 is above the maximum value.
!ad50006000s000602h:ASCA-SIS0-BRIGHT > extract image
!ad50006000s000602h:ASCA-SIS0-BRIGHT > save image outfile=ad50006000s000602h_hi.img
Wrote image to file ad50006000s000602h_hi.img
!ad50006000s000602h:ASCA-SIS0-BRIGHT > exit save_session=no
-> Generating exposure map ad50006000s100102h.expo
ASCAEXPO_V0.9b
reading data file: ad50006000s100102h.evt
reading gti ext: STDGTI
reading hp ext: HOT_PIXELS
reading cal file: s1_teldef_ascalin.fits
making an inst map...
SIS AREA DISC ENABL OFF
CHIP: 0 1 2 3
CCD POWER ON/OFF: ON ON ON ON
AREA DISC IN/OUT: OUT OUT OUT IN
AREA DISC H START: 6 6 6 119
AREA DISC H STOP: 425 425 425 230
AREA DISC V START: 2 2 2 140
AREA DISC V STOP: 422 422 422 220
reading att file: ./fa930427_2350.1950
making an exposure map...
Aspect RA/DEC/ROLL : 288.4410 4.9767 286.0800
Mean RA/DEC/ROLL : 288.4411 4.9634 286.0800
Pnt RA/DEC/ROLL : 288.4445 4.9891 286.0800
Image rebin factor : 4
Attitude Records : 61026
Hot Pixels : 474
GTI intervals : 41
Total GTI (secs) : 17516.768
Max attitude excursion (arcsecs) : 5.000
0 Percent Complete: Total/live time: 0.0000000 0.0000000
10 Percent Complete: Total/live time: 3041.9487305 3041.9487305
20 Percent Complete: Total/live time: 4041.7622070 4041.7622070
30 Percent Complete: Total/live time: 5685.4248047 5685.4248047
40 Percent Complete: Total/live time: 8021.4252930 8021.4252930
50 Percent Complete: Total/live time: 8975.3935547 8975.3935547
60 Percent Complete: Total/live time: 11321.8945312 11321.8945312
70 Percent Complete: Total/live time: 13135.0830078 13135.0830078
80 Percent Complete: Total/live time: 16033.0527344 16033.0527344
90 Percent Complete: Total/live time: 16033.0527344 16033.0527344
100 Percent Complete: Total/live time: 17516.7695312 17516.7695312
Number of attitude steps used: 38
Number of attitude steps avail: 46189
Mean RA/DEC pixel offset: -59.1684 -16.5470
writing expo file: ad50006000s100102h.expo
closing attitude file...
closing data file...
-> Generating low and high energy images for ad50006000s100102h.evt
** XSELECT V1.3 **
!> Enter session name >[xsel] ad50006000s100102h
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS S1CCDPOW
1 W50 EAST BRIGHT HIGH 28/04/93 03:44:28 0.18E+05 12214 1111
EXTRACTOR vers 2.0 11 Apr 1997.
Getting FITS WCS Keywords
Doing file: /data/data17/seq_proc/50006000.007/ad50006000s100102h.evt
Total Good Bad: Region Time Phase Cut
12214 12214 0 0 0 0
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
12214 12214 0 0 0 0
in 17516.77 seconds
Image has 12214 counts for 0.6973 counts/sec
EXTRACTOR vers 2.0 11 Apr 1997.
Getting FITS WCS Keywords
Doing file: /data/data17/seq_proc/50006000.007/ad50006000s100102h.evt
Total Good Bad: Region Time Phase Cut
12214 6834 0 0 0 5380
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
12214 6834 0 0 0 5380
in 17516.77 seconds
Image has 6834 counts for 0.3901 counts/sec
EXTRACTOR vers 2.0 11 Apr 1997.
Getting FITS WCS Keywords
Doing file: /data/data17/seq_proc/50006000.007/ad50006000s100102h.evt
Total Good Bad: Region Time Phase Cut
12214 5394 0 0 0 6820
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
12214 5394 0 0 0 6820
in 17516.77 seconds
Image has 5394 counts for 0.3079 counts/sec
Command not found; type ? for a command listing
!ad50006000s100102h:ASCA >
!ad50006000s100102h:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!ad50006000s100102h:ASCA > set datadir .
Setting data directory to /data/data17/seq_proc/50006000.007/
Setting mkf directory to /data/data17/seq_proc/50006000.007/
!ad50006000s100102h:ASCA > read events ad50006000s100102h.evt
Got new instrument: SIS1
Setting: IMAGE binning = 4
WMAP binning = 8
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 2047
Got the minimum time resolution of the read data: 16.000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data17/seq_proc/50006000.007/
HK Directory is: /data/data17/seq_proc/50006000.007/
!ad50006000s100102h:ASCA-SIS1-BRIGHT > set image sky
!ad50006000s100102h:ASCA-SIS1-BRIGHT > filter region corner_point.reg
!ad50006000s100102h:ASCA-SIS1-BRIGHT > extract image
!ad50006000s100102h:ASCA-SIS1-BRIGHT > save image outfile=ad50006000s100102h.img
Wrote image to file ad50006000s100102h.img
!ad50006000s100102h:ASCA-SIS1-BRIGHT > filter pha_cut 0 547
!ad50006000s100102h:ASCA-SIS1-BRIGHT > extract image
!ad50006000s100102h:ASCA-SIS1-BRIGHT > save image outfile=ad50006000s100102h_lo.img
Wrote image to file ad50006000s100102h_lo.img
!ad50006000s100102h:ASCA-SIS1-BRIGHT > clear pha_cut
!ad50006000s100102h:ASCA-SIS1-BRIGHT > filter pha_cut 547 2048
Warning: your PI upper bound: 2048 is above the maximum value.
!ad50006000s100102h:ASCA-SIS1-BRIGHT > extract image
!ad50006000s100102h:ASCA-SIS1-BRIGHT > save image outfile=ad50006000s100102h_hi.img
Wrote image to file ad50006000s100102h_hi.img
!ad50006000s100102h:ASCA-SIS1-BRIGHT > exit save_session=no
-> Generating exposure map ad50006000s100202m.expo
ASCAEXPO_V0.9b
reading data file: ad50006000s100202m.evt
reading gti ext: STDGTI
reading hp ext: HOT_PIXELS
reading cal file: s1_teldef_ascalin.fits
making an inst map...
SIS AREA DISC ENABL OFF
CHIP: 0 1 2 3
CCD POWER ON/OFF: ON ON ON ON
AREA DISC IN/OUT: OUT OUT OUT IN
AREA DISC H START: 6 6 6 119
AREA DISC H STOP: 425 425 425 230
AREA DISC V START: 2 2 2 140
AREA DISC V STOP: 422 422 422 220
reading att file: ./fa930427_2350.1950
making an exposure map...
Aspect RA/DEC/ROLL : 288.4410 4.9767 286.0801
Mean RA/DEC/ROLL : 288.4423 4.9612 286.0801
Pnt RA/DEC/ROLL : 288.2650 5.0632 286.0801
Image rebin factor : 4
Attitude Records : 61026
Hot Pixels : 423
GTI intervals : 22
Total GTI (secs) : 11101.559
Max attitude excursion (arcsecs) : 5.000
0 Percent Complete: Total/live time: 0.0000000 0.0000000
10 Percent Complete: Total/live time: 1483.9912109 1483.9912109
20 Percent Complete: Total/live time: 2719.9997559 2719.9997559
30 Percent Complete: Total/live time: 3459.9738770 3459.9738770
40 Percent Complete: Total/live time: 5195.9677734 5195.9677734
50 Percent Complete: Total/live time: 5695.9995117 5695.9995117
60 Percent Complete: Total/live time: 8576.0000000 8576.0000000
70 Percent Complete: Total/live time: 8576.0000000 8576.0000000
80 Percent Complete: Total/live time: 9553.7548828 9553.7548828
90 Percent Complete: Total/live time: 10593.1406250 10593.1406250
100 Percent Complete: Total/live time: 11101.5595703 11101.5595703
Number of attitude steps used: 54
Number of attitude steps avail: 10888
Mean RA/DEC pixel offset: -60.1363 -27.0341
writing expo file: ad50006000s100202m.expo
closing attitude file...
closing data file...
-> Generating low and high energy images for ad50006000s100202m.evt
** XSELECT V1.3 **
!> Enter session name >[xsel] ad50006000s100202m
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS S1CCDPOW
1 W50 EAST BRIGHT MEDIUM 27/04/93 23:50:32 0.11E+05 7884 1111
EXTRACTOR vers 2.0 11 Apr 1997.
Getting FITS WCS Keywords
Doing file: /data/data17/seq_proc/50006000.007/ad50006000s100202m.evt
Total Good Bad: Region Time Phase Cut
7884 7884 0 0 0 0
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
7884 7884 0 0 0 0
in 11101.56 seconds
Image has 7884 counts for 0.7102 counts/sec
EXTRACTOR vers 2.0 11 Apr 1997.
Getting FITS WCS Keywords
Doing file: /data/data17/seq_proc/50006000.007/ad50006000s100202m.evt
Total Good Bad: Region Time Phase Cut
7884 4294 0 0 0 3590
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
7884 4294 0 0 0 3590
in 11101.56 seconds
Image has 4294 counts for 0.3868 counts/sec
EXTRACTOR vers 2.0 11 Apr 1997.
Getting FITS WCS Keywords
Doing file: /data/data17/seq_proc/50006000.007/ad50006000s100202m.evt
Total Good Bad: Region Time Phase Cut
7884 3594 0 0 0 4290
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
7884 3594 0 0 0 4290
in 11101.56 seconds
Image has 3594 counts for 0.3237 counts/sec
Command not found; type ? for a command listing
!ad50006000s100202m:ASCA >
!ad50006000s100202m:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!ad50006000s100202m:ASCA > set datadir .
Setting data directory to /data/data17/seq_proc/50006000.007/
Setting mkf directory to /data/data17/seq_proc/50006000.007/
!ad50006000s100202m:ASCA > read events ad50006000s100202m.evt
Got new instrument: SIS1
Setting: IMAGE binning = 4
WMAP binning = 8
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 2047
Got the minimum time resolution of the read data: 16.000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data17/seq_proc/50006000.007/
HK Directory is: /data/data17/seq_proc/50006000.007/
!ad50006000s100202m:ASCA-SIS1-BRIGHT > set image sky
!ad50006000s100202m:ASCA-SIS1-BRIGHT > filter region corner_point.reg
!ad50006000s100202m:ASCA-SIS1-BRIGHT > extract image
!ad50006000s100202m:ASCA-SIS1-BRIGHT > save image outfile=ad50006000s100202m.img
Wrote image to file ad50006000s100202m.img
!ad50006000s100202m:ASCA-SIS1-BRIGHT > filter pha_cut 0 547
!ad50006000s100202m:ASCA-SIS1-BRIGHT > extract image
!ad50006000s100202m:ASCA-SIS1-BRIGHT > save image outfile=ad50006000s100202m_lo.img
Wrote image to file ad50006000s100202m_lo.img
!ad50006000s100202m:ASCA-SIS1-BRIGHT > clear pha_cut
!ad50006000s100202m:ASCA-SIS1-BRIGHT > filter pha_cut 547 2048
Warning: your PI upper bound: 2048 is above the maximum value.
!ad50006000s100202m:ASCA-SIS1-BRIGHT > extract image
!ad50006000s100202m:ASCA-SIS1-BRIGHT > save image outfile=ad50006000s100202m_hi.img
Wrote image to file ad50006000s100202m_hi.img
!ad50006000s100202m:ASCA-SIS1-BRIGHT > exit save_session=no
-> Generating exposure map ad50006000s100502m.expo
ASCAEXPO_V0.9b
reading data file: ad50006000s100502m.evt
reading gti ext: STDGTI
reading hp ext: HOT_PIXELS
reading cal file: s1_teldef_ascalin.fits
making an inst map...
SIS AREA DISC ENABL OFF
CHIP: 0 1 2 3
CCD POWER ON/OFF: ON ON ON ON
AREA DISC IN/OUT: OUT OUT OUT IN
AREA DISC H START: 6 6 6 119
AREA DISC H STOP: 425 425 425 230
AREA DISC V START: 2 2 2 140
AREA DISC V STOP: 422 422 422 220
reading att file: ./fa930428_1949.2350
making an exposure map...
Aspect RA/DEC/ROLL : 288.4410 4.9767 286.0821
Mean RA/DEC/ROLL : 288.4391 4.9610 286.0821
Pnt RA/DEC/ROLL : 288.4455 4.9875 286.0821
Image rebin factor : 4
Attitude Records : 6339
Hot Pixels : 285
GTI intervals : 16
Total GTI (secs) : 5608.037
Max attitude excursion (arcsecs) : 5.000
0 Percent Complete: Total/live time: 0.0000000 0.0000000
10 Percent Complete: Total/live time: 1184.0000000 1184.0000000
20 Percent Complete: Total/live time: 1184.0000000 1184.0000000
30 Percent Complete: Total/live time: 2011.9859619 2011.9859619
40 Percent Complete: Total/live time: 2427.9846191 2427.9846191
50 Percent Complete: Total/live time: 4128.0000000 4128.0000000
60 Percent Complete: Total/live time: 4128.0000000 4128.0000000
70 Percent Complete: Total/live time: 4131.9711914 4131.9711914
80 Percent Complete: Total/live time: 4768.0000000 4768.0000000
90 Percent Complete: Total/live time: 5216.0000000 5216.0000000
100 Percent Complete: Total/live time: 5608.0371094 5608.0371094
Number of attitude steps used: 19
Number of attitude steps avail: 2471
Mean RA/DEC pixel offset: -69.9026 -25.1900
writing expo file: ad50006000s100502m.expo
closing attitude file...
closing data file...
-> Generating low and high energy images for ad50006000s100502m.evt
** XSELECT V1.3 **
!> Enter session name >[xsel] ad50006000s100502m
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS S1CCDPOW
1 W50 EAST BRIGHT MEDIUM 28/04/93 19:50:16 0.56E+04 4002 1111
EXTRACTOR vers 2.0 11 Apr 1997.
Getting FITS WCS Keywords
Doing file: /data/data17/seq_proc/50006000.007/ad50006000s100502m.evt
Total Good Bad: Region Time Phase Cut
4002 4002 0 0 0 0
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
4002 4002 0 0 0 0
in 5608.04 seconds
Image has 4002 counts for 0.7136 counts/sec
EXTRACTOR vers 2.0 11 Apr 1997.
Getting FITS WCS Keywords
Doing file: /data/data17/seq_proc/50006000.007/ad50006000s100502m.evt
Total Good Bad: Region Time Phase Cut
4002 2321 0 0 0 1681
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
4002 2321 0 0 0 1681
in 5608.04 seconds
Image has 2321 counts for 0.4139 counts/sec
EXTRACTOR vers 2.0 11 Apr 1997.
Getting FITS WCS Keywords
Doing file: /data/data17/seq_proc/50006000.007/ad50006000s100502m.evt
Total Good Bad: Region Time Phase Cut
4002 1682 0 0 0 2320
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
4002 1682 0 0 0 2320
in 5608.04 seconds
Image has 1682 counts for 0.2999 counts/sec
Command not found; type ? for a command listing
!ad50006000s100502m:ASCA >
!ad50006000s100502m:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!ad50006000s100502m:ASCA > set datadir .
Setting data directory to /data/data17/seq_proc/50006000.007/
Setting mkf directory to /data/data17/seq_proc/50006000.007/
!ad50006000s100502m:ASCA > read events ad50006000s100502m.evt
Got new instrument: SIS1
Setting: IMAGE binning = 4
WMAP binning = 8
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 2047
Got the minimum time resolution of the read data: 16.000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data17/seq_proc/50006000.007/
HK Directory is: /data/data17/seq_proc/50006000.007/
!ad50006000s100502m:ASCA-SIS1-BRIGHT > set image sky
!ad50006000s100502m:ASCA-SIS1-BRIGHT > filter region corner_point.reg
!ad50006000s100502m:ASCA-SIS1-BRIGHT > extract image
!ad50006000s100502m:ASCA-SIS1-BRIGHT > save image outfile=ad50006000s100502m.img
Wrote image to file ad50006000s100502m.img
!ad50006000s100502m:ASCA-SIS1-BRIGHT > filter pha_cut 0 547
!ad50006000s100502m:ASCA-SIS1-BRIGHT > extract image
!ad50006000s100502m:ASCA-SIS1-BRIGHT > save image outfile=ad50006000s100502m_lo.img
Wrote image to file ad50006000s100502m_lo.img
!ad50006000s100502m:ASCA-SIS1-BRIGHT > clear pha_cut
!ad50006000s100502m:ASCA-SIS1-BRIGHT > filter pha_cut 547 2048
Warning: your PI upper bound: 2048 is above the maximum value.
!ad50006000s100502m:ASCA-SIS1-BRIGHT > extract image
!ad50006000s100502m:ASCA-SIS1-BRIGHT > save image outfile=ad50006000s100502m_hi.img
Wrote image to file ad50006000s100502m_hi.img
!ad50006000s100502m:ASCA-SIS1-BRIGHT > exit save_session=no
-> Generating exposure map ad50006000s100602h.expo
ASCAEXPO_V0.9b
reading data file: ad50006000s100602h.evt
reading gti ext: STDGTI
reading hp ext: HOT_PIXELS
reading cal file: s1_teldef_ascalin.fits
making an inst map...
SIS AREA DISC ENABL OFF
CHIP: 0 1 2 3
CCD POWER ON/OFF: ON ON ON ON
AREA DISC IN/OUT: OUT OUT OUT IN
AREA DISC H START: 6 6 6 119
AREA DISC H STOP: 425 425 425 230
AREA DISC V START: 2 2 2 140
AREA DISC V STOP: 422 422 422 220
reading att file: ./fa930428_1949.2350
making an exposure map...
Aspect RA/DEC/ROLL : 288.4410 4.9767 286.0832
Mean RA/DEC/ROLL : 288.4385 4.9582 286.0832
Pnt RA/DEC/ROLL : 288.4451 4.9931 286.0832
Image rebin factor : 4
Attitude Records : 6339
Hot Pixels : 204
GTI intervals : 2
Total GTI (secs) : 1421.932
Max attitude excursion (arcsecs) : 5.000
0 Percent Complete: Total/live time: 0.0000000 0.0000000
10 Percent Complete: Total/live time: 263.4665527 263.4665527
20 Percent Complete: Total/live time: 1421.9317627 1421.9317627
100 Percent Complete: Total/live time: 1421.9317627 1421.9317627
Number of attitude steps used: 4
Number of attitude steps avail: 2970
Mean RA/DEC pixel offset: -59.3773 -26.6309
writing expo file: ad50006000s100602h.expo
closing attitude file...
closing data file...
-> Generating low and high energy images for ad50006000s100602h.evt
** XSELECT V1.3 **
!> Enter session name >[xsel] ad50006000s100602h
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS S1CCDPOW
1 W50 EAST BRIGHT HIGH 28/04/93 22:52:12 0.14E+04 1095 1111
EXTRACTOR vers 2.0 11 Apr 1997.
Getting FITS WCS Keywords
Doing file: /data/data17/seq_proc/50006000.007/ad50006000s100602h.evt
Total Good Bad: Region Time Phase Cut
1095 1095 0 0 0 0
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
1095 1095 0 0 0 0
in 1421.93 seconds
Image has 1095 counts for 0.7701 counts/sec
EXTRACTOR vers 2.0 11 Apr 1997.
Getting FITS WCS Keywords
Doing file: /data/data17/seq_proc/50006000.007/ad50006000s100602h.evt
Total Good Bad: Region Time Phase Cut
1095 664 0 0 0 431
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
1095 664 0 0 0 431
in 1421.93 seconds
Image has 664 counts for 0.4670 counts/sec
EXTRACTOR vers 2.0 11 Apr 1997.
Getting FITS WCS Keywords
Doing file: /data/data17/seq_proc/50006000.007/ad50006000s100602h.evt
Total Good Bad: Region Time Phase Cut
1095 432 0 0 0 663
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
1095 432 0 0 0 663
in 1421.93 seconds
Image has 432 counts for 0.3038 counts/sec
Command not found; type ? for a command listing
!ad50006000s100602h:ASCA >
!ad50006000s100602h:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!ad50006000s100602h:ASCA > set datadir .
Setting data directory to /data/data17/seq_proc/50006000.007/
Setting mkf directory to /data/data17/seq_proc/50006000.007/
!ad50006000s100602h:ASCA > read events ad50006000s100602h.evt
Got new instrument: SIS1
Setting: IMAGE binning = 4
WMAP binning = 8
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 2047
Got the minimum time resolution of the read data: 16.000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data17/seq_proc/50006000.007/
HK Directory is: /data/data17/seq_proc/50006000.007/
!ad50006000s100602h:ASCA-SIS1-BRIGHT > set image sky
!ad50006000s100602h:ASCA-SIS1-BRIGHT > filter region corner_point.reg
!ad50006000s100602h:ASCA-SIS1-BRIGHT > extract image
!ad50006000s100602h:ASCA-SIS1-BRIGHT > save image outfile=ad50006000s100602h.img
Wrote image to file ad50006000s100602h.img
!ad50006000s100602h:ASCA-SIS1-BRIGHT > filter pha_cut 0 547
!ad50006000s100602h:ASCA-SIS1-BRIGHT > extract image
!ad50006000s100602h:ASCA-SIS1-BRIGHT > save image outfile=ad50006000s100602h_lo.img
Wrote image to file ad50006000s100602h_lo.img
!ad50006000s100602h:ASCA-SIS1-BRIGHT > clear pha_cut
!ad50006000s100602h:ASCA-SIS1-BRIGHT > filter pha_cut 547 2048
Warning: your PI upper bound: 2048 is above the maximum value.
!ad50006000s100602h:ASCA-SIS1-BRIGHT > extract image
!ad50006000s100602h:ASCA-SIS1-BRIGHT > save image outfile=ad50006000s100602h_hi.img
Wrote image to file ad50006000s100602h_hi.img
!ad50006000s100602h:ASCA-SIS1-BRIGHT > exit save_session=no
-> Summing sis imagesad50006000s000102h.expo ad50006000s000202m.expo ad50006000s000302h.expo ad50006000s000502m.expo ad50006000s000602h.expo ad50006000s100102h.expo ad50006000s100202m.expo ad50006000s100502m.expo ad50006000s100602h.expo-> Summing the following images to produce ad50006000sis32002_all.totsky
ad50006000s000102h.img ad50006000s000202m.img ad50006000s000302h.img ad50006000s000502m.img ad50006000s000602h.img ad50006000s100102h.img ad50006000s100202m.img ad50006000s100502m.img ad50006000s100602h.img-> Summing the following images to produce ad50006000sis32002_lo.totsky
ad50006000s000102h_lo.img ad50006000s000202m_lo.img ad50006000s000302h_lo.img ad50006000s000502m_lo.img ad50006000s000602h_lo.img ad50006000s100102h_lo.img ad50006000s100202m_lo.img ad50006000s100502m_lo.img ad50006000s100602h_lo.img-> Summing the following images to produce ad50006000sis32002_hi.totsky
ad50006000s000102h_hi.img ad50006000s000202m_hi.img ad50006000s000302h_hi.img ad50006000s000502m_hi.img ad50006000s000602h_hi.img ad50006000s100102h_hi.img ad50006000s100202m_hi.img ad50006000s100502m_hi.img ad50006000s100602h_hi.img-> Running XIMAGE to create ad50006000sis32002.gif
No of detectors read in: 20 ![1]XIMAGE> read/fits ad50006000sis32002_all.totsky Reading an image Telescope ASCA SIS0 Image display size = 320 Done, closing file Largest, Smallest 10.00000 0. Bscale, Bzero from file 1.0000000000000 0. After internal scaling Bscale and Bzero 1.0000000000000 0. Image level, max: 10 min: 0 ![2]XIMAGE> read/exp_map ad50006000sis32002.totexpo Reading an image Telescope ASCA SIS0 Image display size = 320 Done, closing file Largest, Smallest 1186.55 0. Bscale, Bzero from file 1.0000000000000 0. After internal scaling Bscale and Bzero 1.0000000000000 0. Image level, max: 1186 min: 0 ![3]XIMAGE> smooth ![4]XIMAGE> cpd /ppm ![5]XIMAGE> cey 2000 ![6]XIMAGE> disp/correct/noframe Displaying image The image is exposure corrected Min = 0 max = 1271 ![7]XIMAGE> grid ![8]XIMAGE> scale scal_f, min_inten 1.00000 0. i,inten,mm,pp 1 0. 0 0 i,inten,mm,pp 2 5.00000 50 -1 i,inten,mm,pp 3 9.00000 90 -1 i,inten,mm,pp 4 13.0000 13 0 ![9]XIMAGE> exit-> Summing gis images
ad50006000g200170m.expo ad50006000g200270h.expo ad50006000g200470m.expo ad50006000g200570h.expo ad50006000g300170m.expo ad50006000g300270h.expo ad50006000g300470m.expo ad50006000g300570h.expo-> Summing the following images to produce ad50006000gis25670_all.totsky
ad50006000g200170m.img ad50006000g200270h.img ad50006000g200470m.img ad50006000g200570h.img ad50006000g300170m.img ad50006000g300270h.img ad50006000g300470m.img ad50006000g300570h.img-> Summing the following images to produce ad50006000gis25670_lo.totsky
ad50006000g200170m_lo.img ad50006000g200270h_lo.img ad50006000g200470m_lo.img ad50006000g200570h_lo.img ad50006000g300170m_lo.img ad50006000g300270h_lo.img ad50006000g300470m_lo.img ad50006000g300570h_lo.img-> Summing the following images to produce ad50006000gis25670_hi.totsky
ad50006000g200170m_hi.img ad50006000g200270h_hi.img ad50006000g200470m_hi.img ad50006000g200570h_hi.img ad50006000g300170m_hi.img ad50006000g300270h_hi.img ad50006000g300470m_hi.img ad50006000g300570h_hi.img-> Running XIMAGE to create ad50006000gis25670.gif
No of detectors read in: 20 ![1]XIMAGE> read/fits ad50006000gis25670_all.totsky Reading an image Telescope ASCA GIS2 Image display size = 256 Done, closing file Largest, Smallest 23.0000 0. Bscale, Bzero from file 1.0000000000000 0. After internal scaling Bscale and Bzero 1.0000000000000 0. Image level, max: 23 min: 0 ![2]XIMAGE> read/exp_map ad50006000gis25670.totexpo Reading an image Telescope ASCA GIS2 Image display size = 256 Done, closing file Largest, Smallest 1256.52 0. Bscale, Bzero from file 1.0000000000000 0. After internal scaling Bscale and Bzero 1.0000000000000 0. Image level, max: 1256 min: 0 ![3]XIMAGE> smooth ![4]XIMAGE> cpd /ppm ![5]XIMAGE> cey 2000 ![6]XIMAGE> disp/correct/noframe Displaying image The image is exposure corrected Min = 0 max = 32767 ![7]XIMAGE> grid ![8]XIMAGE> scale scal_f, min_inten 1.00000 0. i,inten,mm,pp 1 0. 0 0 i,inten,mm,pp 2 4.00000 40 -1 i,inten,mm,pp 3 9.00000 90 -1 i,inten,mm,pp 4 16.0000 16 0 ![9]XIMAGE> exit
104 121 0.000185698 110 33 9.44149-> Smoothing ad50006000gis25670_hi.totsky with ad50006000gis25670.totexpo
104 120 0.000113482 110 29 10.876-> Smoothing ad50006000gis25670_lo.totsky with ad50006000gis25670.totexpo
103 122 9.28492e-05 110 35 9.91775-> Determining extraction radii
104 121 33 T-> Standard Output From STOOL colorpic:
color plane 0 color plane 1 color plane 2 writing image image written-> Creating fits catalog of sources: ad50006000gis25670.src
95 141 5.67629e-05 220 99 8.57441-> Smoothing ad50006000sis32002_hi.totsky with ad50006000sis32002.totexpo
91 146 2.63785e-05 222 53 7.43879-> Smoothing ad50006000sis32002_lo.totsky with ad50006000sis32002.totexpo
96 143 3.59714e-05 219 97 9.723-> Determining extraction radii
95 141 99 T-> Standard Output From STOOL colorpic:
color plane 0 color plane 1 color plane 2 writing image image written-> Creating fits catalog of sources: ad50006000sis32002.src
The sum of the selected column is 945.00000 The mean of the selected column is 472.50000 The standard deviation of the selected column is 3.5355339 The minimum of selected column is 470.00000 The maximum of selected column is 475.00000 The number of points used in calculation is 2-> Standard Output From FTOOL fstatistic:
The sum of the selected column is 1629.0000 The mean of the selected column is 814.50000 The standard deviation of the selected column is 13.435029 The minimum of selected column is 805.00000 The maximum of selected column is 824.00000 The number of points used in calculation is 2-> Converting (380.0,564.0,2.0) to s1 detector coordinates
The sum of the selected column is 1871.0000 The mean of the selected column is 467.75000 The standard deviation of the selected column is 4.4253060 The minimum of selected column is 463.00000 The maximum of selected column is 472.00000 The number of points used in calculation is 4-> Standard Output From FTOOL fstatistic:
The sum of the selected column is 3431.0000 The mean of the selected column is 857.75000 The standard deviation of the selected column is 5.1881275 The minimum of selected column is 850.00000 The maximum of selected column is 861.00000 The number of points used in calculation is 4-> Converting (104.0,121.0,2.0) to g2 detector coordinates
The sum of the selected column is 9202.0000 The mean of the selected column is 108.25882 The standard deviation of the selected column is 1.0136326 The minimum of selected column is 106.00000 The maximum of selected column is 110.00000 The number of points used in calculation is 85-> Standard Output From FTOOL fstatistic:
The sum of the selected column is 12683.000 The mean of the selected column is 149.21176 The standard deviation of the selected column is 1.3101628 The minimum of selected column is 146.00000 The maximum of selected column is 152.00000 The number of points used in calculation is 85-> Converting (104.0,121.0,2.0) to g3 detector coordinates
The sum of the selected column is 11652.000 The mean of the selected column is 114.23529 The standard deviation of the selected column is 1.2037604 The minimum of selected column is 111.00000 The maximum of selected column is 117.00000 The number of points used in calculation is 102-> Standard Output From FTOOL fstatistic:
The sum of the selected column is 15268.000 The mean of the selected column is 149.68627 The standard deviation of the selected column is 1.2663223 The minimum of selected column is 146.00000 The maximum of selected column is 153.00000 The number of points used in calculation is 102
1 ad50006000s000102h.evt 22192 1 ad50006000s000202m.evt 22192 1 ad50006000s000502m.evt 22192 1 ad50006000s000602h.evt 22192 2 ad50006000s000302h.evt 1341-> Fetching SIS0_OFFCHIP.1
ad50006000s000102h.evt ad50006000s000202m.evt ad50006000s000502m.evt ad50006000s000602h.evt-> Standard Output From FTOOL xselect:
** XSELECT V1.3 **
!> Enter session name >[xsel] xsel
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS S0CCDPOW
1 W50 EAST BRIGHT HIGH 28/04/93 03:44:28 0.16E+05 10231 1111
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS S0CCDPOW
1 W50 EAST BRIGHT HIGH 28/04/93 03:44:28 0.16E+05 10231 1111
2 W50 EAST BRIGHT MEDIUM 27/04/93 23:50:32 0.11E+05 7322 1111
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS S0CCDPOW
1 W50 EAST BRIGHT HIGH 28/04/93 03:44:28 0.16E+05 10231 1111
2 W50 EAST BRIGHT MEDIUM 27/04/93 23:50:32 0.11E+05 7322 1111
3 W50 EAST BRIGHT MEDIUM 28/04/93 19:50:16 0.55E+04 3663 1111
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS S0CCDPOW
1 W50 EAST BRIGHT HIGH 28/04/93 03:44:28 0.16E+05 10231 1111
2 W50 EAST BRIGHT MEDIUM 27/04/93 23:50:32 0.11E+05 7322 1111
3 W50 EAST BRIGHT MEDIUM 28/04/93 19:50:16 0.55E+04 3663 1111
4 W50 EAST BRIGHT HIGH 28/04/93 22:52:12 0.15E+04 976 1111
EXTRACTOR vers 2.0 11 Apr 1997.
Getting FITS WCS Keywords
Doing file: /data/data17/seq_proc/50006000.007/ad50006000s000102h.evt
Total Good Bad: Region Time Phase Cut
10231 6257 3974 0 0 0
Doing file: /data/data17/seq_proc/50006000.007/ad50006000s000202m.evt
Total Good Bad: Region Time Phase Cut
7322 4365 2957 0 0 0
Doing file: /data/data17/seq_proc/50006000.007/ad50006000s000502m.evt
Total Good Bad: Region Time Phase Cut
3663 2177 1486 0 0 0
Doing file: /data/data17/seq_proc/50006000.007/ad50006000s000602h.evt
Total Good Bad: Region Time Phase Cut
976 617 359 0 0 0
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
22192 13416 8776 0 0 0
in 33605.21 seconds
Spectrum has 13416 counts for 0.3992 counts/sec
-------------------------
MANDATORY KEYWORDS/VALUES
-------------------------
--------------------------------------------------------------------
--------------------------------------------------------------------
EXTNAME - SPECTRUM Name of this BINTABLE
TELESCOP - ASCA Mission/Satellite name
INSTRUME - SIS0 Instrument/Detector
FILTER - Instrument filter in use
EXPOSURE - 33605. Integration time (in secs) of PHA data
AREASCAL - 1.0000 Area scaling factor
BACKSCAL - 0.23224 Background scaling factor
BACKFILE - NONE Associated background file
CORRSCAL - 1.0000 Correlation scaling factor
CORRFILE - none Associated correlation file
RESPFILE - NONE Associated redistribution matrix file
ANCRFILE - none Associated ancillary response file
XFLT0001 - none XSPEC selection filter
POISSERR - TRUE Whether Poissonian errors apply
CHANTYPE - PI Whether channels have been corrected
TLMIN1 - 0 First legal Detector channel
DETCHANS - 512 No. of legal detector channels
NCHAN - 512 No. of detector channels in dataset
PHAVERSN - 1.1.0 OGIP FITS version number
STAT_ERR - FALSE Statistical Error
SYS_ERR - TRUE Fractional Systematic Error
QUALITY - TRUE Quality Flag
GROUPING - FALSE Grouping Flag
--------------------------------------------------------------------
--------------------------------------------------------------------
... QUALITY
...
... -------
... QUALITY
... -------
... Bad Channels (Channel - Channel)
... ---------------------------------------------
... 0 - 12 have quality 5
... ---------------------------------------------
...
...... exiting, changes written to file : ad50006000s010102_1.pi
EXTRACTOR vers 2.0 11 Apr 1997.
Doing file: /data/data17/seq_proc/50006000.007/ad50006000s000102h.evt
Total Good Bad: Region Time Phase Cut
10231 6257 3974 0 0 0
Writing events file
6257 events written to the output file
Doing file: /data/data17/seq_proc/50006000.007/ad50006000s000202m.evt
Total Good Bad: Region Time Phase Cut
7322 4365 2957 0 0 0
Writing events file
10622 events written to the output file
Doing file: /data/data17/seq_proc/50006000.007/ad50006000s000502m.evt
Total Good Bad: Region Time Phase Cut
3663 2177 1486 0 0 0
Writing events file
12799 events written to the output file
Doing file: /data/data17/seq_proc/50006000.007/ad50006000s000602h.evt
Total Good Bad: Region Time Phase Cut
976 617 359 0 0 0
Writing events file
13416 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
22192 13416 8776 0 0 0
in 33605.21 seconds
Command not found; type ? for a command listing
!xsel:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!xsel:ASCA > set datadir .
Setting data directory to /data/data17/seq_proc/50006000.007/
Setting mkf directory to /data/data17/seq_proc/50006000.007/
!xsel:ASCA > read events ad50006000s000102h.evt
Got new instrument: SIS0
Setting: IMAGE binning = 4
WMAP binning = 8
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 2047
Got the minimum time resolution of the read data: 16.000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data17/seq_proc/50006000.007/
HK Directory is: /data/data17/seq_proc/50006000.007/
!xsel:ASCA-SIS0-BRIGHT > read events ad50006000s000202m.evt
Getting Min and Max for Energy Column...
Got min and max for PI: 0 2047
Got the minimum time resolution of the read data: 16.000
Number of files read in: 2
******************** Observation Catalogue ********************
Data Directory is: /data/data17/seq_proc/50006000.007/
HK Directory is: /data/data17/seq_proc/50006000.007/
!xsel:ASCA-SIS0-BRIGHT > read events ad50006000s000502m.evt
Getting Min and Max for Energy Column...
Got min and max for PI: 0 2047
Got the minimum time resolution of the read data: 16.000
Number of files read in: 3
******************** Observation Catalogue ********************
Data Directory is: /data/data17/seq_proc/50006000.007/
HK Directory is: /data/data17/seq_proc/50006000.007/
!xsel:ASCA-SIS0-BRIGHT > read events ad50006000s000602h.evt
Getting Min and Max for Energy Column...
Got min and max for PI: 0 2047
Got the minimum time resolution of the read data: 16.000
Number of files read in: 4
******************** Observation Catalogue ********************
Data Directory is: /data/data17/seq_proc/50006000.007/
HK Directory is: /data/data17/seq_proc/50006000.007/
!xsel:ASCA-SIS0-BRIGHT > set phaname PI
!xsel:ASCA-SIS0-BRIGHT > filter region ad50006000s032002_1.reg
!xsel:ASCA-SIS0-BRIGHT > filter region SIS0_OFFCHIP.1
!xsel:ASCA-SIS0-BRIGHT > filter region ad50006000s010102.discrim
!xsel:ASCA-SIS0-BRIGHT > extract spectrum
!xsel:ASCA-SIS0-BRIGHT > save spectrum ad50006000s010102_1.pi group=yes
Wrote spectrum to ad50006000s010102_1.pi
!xsel:ASCA-SIS0-BRIGHT > extract events
!xsel:ASCA-SIS0-BRIGHT > save events outfile=events.tmp use_events=yes
Wrote events list to file events.tmp
Changing Data directory from:
/data/data17/seq_proc/50006000.007/
to the current working directory.
!xsel:ASCA-SIS0-BRIGHT > exit save_session=no
-> Grouping ad50006000s010102_1.pi to 40 counts/bin------------------------- MANDATORY KEYWORDS/VALUES ------------------------- -------------------------------------------------------------------- -------------------------------------------------------------------- EXTNAME - SPECTRUM Name of this BINTABLE TELESCOP - ASCA Mission/Satellite name INSTRUME - SIS0 Instrument/Detector FILTER - Instrument filter in use EXPOSURE - 33605. Integration time (in secs) of PHA data AREASCAL - 1.0000 Area scaling factor BACKSCAL - 0.23224 Background scaling factor BACKFILE - NONE Associated background file CORRSCAL - 1.0000 Correlation scaling factor CORRFILE - none Associated correlation file RESPFILE - NONE Associated redistribution matrix file ANCRFILE - none Associated ancillary response file XFLT0001 - none XSPEC selection filter POISSERR - TRUE Whether Poissonian errors apply CHANTYPE - PI Whether channels have been corrected TLMIN1 - 0 First legal Detector channel DETCHANS - 512 No. of legal detector channels NCHAN - 512 No. of detector channels in dataset PHAVERSN - 1.1.0 OGIP FITS version number STAT_ERR - FALSE Statistical Error SYS_ERR - TRUE Fractional Systematic Error QUALITY - TRUE Quality Flag GROUPING - FALSE Grouping Flag -------------------------------------------------------------------- -------------------------------------------------------------------- ... ... -------- ... GROUPING ... -------- ... --------------------------------------------- ... Channel Grouping (Channel-Channel) : ... 0 - 12 of undefined grouping (Channel quality=bad) ... 13 - 91 are single channels ... 92 - 93 are grouped by a factor 2 ... 94 - 102 are single channels ... 103 - 104 are grouped by a factor 2 ... 105 - 109 are single channels ... 110 - 117 are grouped by a factor 2 ... 118 - 119 are single channels ... 120 - 127 are grouped by a factor 2 ... 128 - 128 are single channels ... 129 - 142 are grouped by a factor 2 ... 143 - 145 are grouped by a factor 3 ... 146 - 153 are grouped by a factor 2 ... 154 - 156 are grouped by a factor 3 ... 157 - 160 are grouped by a factor 2 ... 161 - 172 are grouped by a factor 3 ... 173 - 184 are grouped by a factor 4 ... 185 - 187 are grouped by a factor 3 ... 188 - 191 are grouped by a factor 4 ... 192 - 196 are grouped by a factor 5 ... 197 - 200 are grouped by a factor 4 ... 201 - 206 are grouped by a factor 6 ... 207 - 213 are grouped by a factor 7 ... 214 - 219 are grouped by a factor 6 ... 220 - 237 are grouped by a factor 9 ... 238 - 247 are grouped by a factor 10 ... 248 - 254 are grouped by a factor 7 ... 255 - 258 are grouped by a factor 4 ... 259 - 278 are grouped by a factor 20 ... 279 - 295 are grouped by a factor 17 ... 296 - 327 are grouped by a factor 32 ... 328 - 351 are grouped by a factor 24 ... 352 - 381 are grouped by a factor 30 ... 382 - 408 are grouped by a factor 27 ... 409 - 440 are grouped by a factor 32 ... 441 - 462 are grouped by a factor 22 ... 463 - 466 are grouped by a factor 4 ... 467 - 478 are grouped by a factor 3 ... 479 - 486 are grouped by a factor 4 ... --------------------------------------------- ... ...... exiting, changes written to file : ad50006000s010102_1.pi ** grppha 2.6.0 completed successfully-> Source occupies chip(s) 0 1 2 3
** XSELECT V1.3 **
!> Enter session name >[xsel] xsel
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS S0CCDPOW
1 W50 EAST BRIGHT HIGH 27/04/93 23:50:32 0.34E+05 13416 1111
EXTRACTOR vers 2.0 11 Apr 1997.
Getting FITS WCS Keywords
Doing file: /data/data17/seq_proc/50006000.007/events.tmp
Total Good Bad: Region Time Phase Cut
13416 7529 5887 0 0 0
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
13416 7529 5887 0 0 0
in 33605.21 seconds
Spectrum has 7529 counts for 0.2240 counts/sec
-------------------------
MANDATORY KEYWORDS/VALUES
-------------------------
--------------------------------------------------------------------
--------------------------------------------------------------------
EXTNAME - SPECTRUM Name of this BINTABLE
TELESCOP - ASCA Mission/Satellite name
INSTRUME - SIS0 Instrument/Detector
FILTER - Instrument filter in use
EXPOSURE - 33605. Integration time (in secs) of PHA data
AREASCAL - 1.0000 Area scaling factor
BACKSCAL - 0.12253 Background scaling factor
BACKFILE - NONE Associated background file
CORRSCAL - 1.0000 Correlation scaling factor
CORRFILE - none Associated correlation file
RESPFILE - NONE Associated redistribution matrix file
ANCRFILE - none Associated ancillary response file
XFLT0001 - none XSPEC selection filter
POISSERR - TRUE Whether Poissonian errors apply
CHANTYPE - PI Whether channels have been corrected
TLMIN1 - 0 First legal Detector channel
DETCHANS - 512 No. of legal detector channels
NCHAN - 512 No. of detector channels in dataset
PHAVERSN - 1.1.0 OGIP FITS version number
STAT_ERR - FALSE Statistical Error
SYS_ERR - TRUE Fractional Systematic Error
QUALITY - TRUE Quality Flag
GROUPING - FALSE Grouping Flag
--------------------------------------------------------------------
--------------------------------------------------------------------
... QUALITY
...
... -------
... QUALITY
... -------
... Bad Channels (Channel - Channel)
... ---------------------------------------------
... 0 - 12 have quality 5
... ---------------------------------------------
...
...... exiting, changes written to file : spec0.tmp
Command not found; type ? for a command listing
!xsel:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!xsel:ASCA > set datadir .
Setting data directory to /data/data17/seq_proc/50006000.007/
Setting mkf directory to /data/data17/seq_proc/50006000.007/
!xsel:ASCA > read events events.tmp
Got new instrument: SIS0
Setting: IMAGE binning = 4
WMAP binning = 8
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 2047
Got the minimum time resolution of the read data: 16.000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data17/seq_proc/50006000.007/
HK Directory is: /data/data17/seq_proc/50006000.007/
!xsel:ASCA-SIS0-BRIGHT > set phaname PI
!xsel:ASCA-SIS0-BRIGHT > filter region ad50006000s032002_1.reg
!xsel:ASCA-SIS0-BRIGHT > filter region SIS0_OFFCHIP.1
!xsel:ASCA-SIS0-BRIGHT > filter region ad50006000s010102.discrim
!xsel:ASCA-SIS0-BRIGHT > filter region SIS0_NOTCHIP1.1
!xsel:ASCA-SIS0-BRIGHT > filter region SIS0_NOTCHIP2.1
!xsel:ASCA-SIS0-BRIGHT > filter region SIS0_NOTCHIP3.1
!xsel:ASCA-SIS0-BRIGHT > extract spectrum
!xsel:ASCA-SIS0-BRIGHT > save spectrum spec0.tmp group=yes
Wrote spectrum to spec0.tmp
!xsel:ASCA-SIS0-BRIGHT > exit save_session=no
-> Fetching sis0c0p40_290296.fitsSisrmg Version 1.1, Configured 04/97 This version resolves *all* known keyword incompatibilities with other FTOOLS tasks. If you have previously fudged *any* keywords in the PHA file to compensate, incorrect results will follow. Setting 1st PHA channel to 0 Making v1.1 1180x512 S0C0 Bright PI RMF Calibration data from ./ Please stand by... ...Done.-> Fetching SIS0_NOTCHIP0.1
** XSELECT V1.3 **
!> Enter session name >[xsel] xsel
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS S0CCDPOW
1 W50 EAST BRIGHT HIGH 27/04/93 23:50:32 0.34E+05 13416 1111
EXTRACTOR vers 2.0 11 Apr 1997.
Getting FITS WCS Keywords
Doing file: /data/data17/seq_proc/50006000.007/events.tmp
Total Good Bad: Region Time Phase Cut
13416 3489 9927 0 0 0
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
13416 3489 9927 0 0 0
in 33605.21 seconds
Spectrum has 3489 counts for 0.1038 counts/sec
-------------------------
MANDATORY KEYWORDS/VALUES
-------------------------
--------------------------------------------------------------------
--------------------------------------------------------------------
EXTNAME - SPECTRUM Name of this BINTABLE
TELESCOP - ASCA Mission/Satellite name
INSTRUME - SIS0 Instrument/Detector
FILTER - Instrument filter in use
EXPOSURE - 33605. Integration time (in secs) of PHA data
AREASCAL - 1.0000 Area scaling factor
BACKSCAL - 6.42578E-02 Background scaling factor
BACKFILE - NONE Associated background file
CORRSCAL - 1.0000 Correlation scaling factor
CORRFILE - none Associated correlation file
RESPFILE - NONE Associated redistribution matrix file
ANCRFILE - none Associated ancillary response file
XFLT0001 - none XSPEC selection filter
POISSERR - TRUE Whether Poissonian errors apply
CHANTYPE - PI Whether channels have been corrected
TLMIN1 - 0 First legal Detector channel
DETCHANS - 512 No. of legal detector channels
NCHAN - 512 No. of detector channels in dataset
PHAVERSN - 1.1.0 OGIP FITS version number
STAT_ERR - FALSE Statistical Error
SYS_ERR - TRUE Fractional Systematic Error
QUALITY - TRUE Quality Flag
GROUPING - FALSE Grouping Flag
--------------------------------------------------------------------
--------------------------------------------------------------------
... QUALITY
...
... -------
... QUALITY
... -------
... Bad Channels (Channel - Channel)
... ---------------------------------------------
... 0 - 12 have quality 5
... ---------------------------------------------
...
...... exiting, changes written to file : spec1.tmp
Command not found; type ? for a command listing
!xsel:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!xsel:ASCA > set datadir .
Setting data directory to /data/data17/seq_proc/50006000.007/
Setting mkf directory to /data/data17/seq_proc/50006000.007/
!xsel:ASCA > read events events.tmp
Got new instrument: SIS0
Setting: IMAGE binning = 4
WMAP binning = 8
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 2047
Got the minimum time resolution of the read data: 16.000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data17/seq_proc/50006000.007/
HK Directory is: /data/data17/seq_proc/50006000.007/
!xsel:ASCA-SIS0-BRIGHT > set phaname PI
!xsel:ASCA-SIS0-BRIGHT > filter region ad50006000s032002_1.reg
!xsel:ASCA-SIS0-BRIGHT > filter region SIS0_OFFCHIP.1
!xsel:ASCA-SIS0-BRIGHT > filter region ad50006000s010102.discrim
!xsel:ASCA-SIS0-BRIGHT > filter region SIS0_NOTCHIP0.1
!xsel:ASCA-SIS0-BRIGHT > filter region SIS0_NOTCHIP2.1
!xsel:ASCA-SIS0-BRIGHT > filter region SIS0_NOTCHIP3.1
!xsel:ASCA-SIS0-BRIGHT > extract spectrum
!xsel:ASCA-SIS0-BRIGHT > save spectrum spec1.tmp group=yes
Wrote spectrum to spec1.tmp
!xsel:ASCA-SIS0-BRIGHT > exit save_session=no
-> Fetching sis0c1p40_290296.fitsSisrmg Version 1.1, Configured 04/97 This version resolves *all* known keyword incompatibilities with other FTOOLS tasks. If you have previously fudged *any* keywords in the PHA file to compensate, incorrect results will follow. Setting 1st PHA channel to 0 Making v1.1 1180x512 S0C1 Bright PI RMF Calibration data from ./ Please stand by... ...Done.-> SIS0_NOTCHIP0.1 already present in current directory
** XSELECT V1.3 **
!> Enter session name >[xsel] xsel
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS S0CCDPOW
1 W50 EAST BRIGHT HIGH 27/04/93 23:50:32 0.34E+05 13416 1111
EXTRACTOR vers 2.0 11 Apr 1997.
Getting FITS WCS Keywords
Doing file: /data/data17/seq_proc/50006000.007/events.tmp
Total Good Bad: Region Time Phase Cut
13416 624 12792 0 0 0
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
13416 624 12792 0 0 0
in 33605.21 seconds
Spectrum has 624 counts for 1.8569E-02 counts/sec
-------------------------
MANDATORY KEYWORDS/VALUES
-------------------------
--------------------------------------------------------------------
--------------------------------------------------------------------
EXTNAME - SPECTRUM Name of this BINTABLE
TELESCOP - ASCA Mission/Satellite name
INSTRUME - SIS0 Instrument/Detector
FILTER - Instrument filter in use
EXPOSURE - 33605. Integration time (in secs) of PHA data
AREASCAL - 1.0000 Area scaling factor
BACKSCAL - 2.93359E-02 Background scaling factor
BACKFILE - NONE Associated background file
CORRSCAL - 1.0000 Correlation scaling factor
CORRFILE - none Associated correlation file
RESPFILE - NONE Associated redistribution matrix file
ANCRFILE - none Associated ancillary response file
XFLT0001 - none XSPEC selection filter
POISSERR - TRUE Whether Poissonian errors apply
CHANTYPE - PI Whether channels have been corrected
TLMIN1 - 0 First legal Detector channel
DETCHANS - 512 No. of legal detector channels
NCHAN - 512 No. of detector channels in dataset
PHAVERSN - 1.1.0 OGIP FITS version number
STAT_ERR - FALSE Statistical Error
SYS_ERR - TRUE Fractional Systematic Error
QUALITY - TRUE Quality Flag
GROUPING - FALSE Grouping Flag
--------------------------------------------------------------------
--------------------------------------------------------------------
... QUALITY
...
... -------
... QUALITY
... -------
... Bad Channels (Channel - Channel)
... ---------------------------------------------
... 0 - 12 have quality 5
... ---------------------------------------------
...
...... exiting, changes written to file : spec2.tmp
Command not found; type ? for a command listing
!xsel:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!xsel:ASCA > set datadir .
Setting data directory to /data/data17/seq_proc/50006000.007/
Setting mkf directory to /data/data17/seq_proc/50006000.007/
!xsel:ASCA > read events events.tmp
Got new instrument: SIS0
Setting: IMAGE binning = 4
WMAP binning = 8
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 2047
Got the minimum time resolution of the read data: 16.000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data17/seq_proc/50006000.007/
HK Directory is: /data/data17/seq_proc/50006000.007/
!xsel:ASCA-SIS0-BRIGHT > set phaname PI
!xsel:ASCA-SIS0-BRIGHT > filter region ad50006000s032002_1.reg
!xsel:ASCA-SIS0-BRIGHT > filter region SIS0_OFFCHIP.1
!xsel:ASCA-SIS0-BRIGHT > filter region ad50006000s010102.discrim
!xsel:ASCA-SIS0-BRIGHT > filter region SIS0_NOTCHIP0.1
!xsel:ASCA-SIS0-BRIGHT > filter region SIS0_NOTCHIP1.1
!xsel:ASCA-SIS0-BRIGHT > filter region SIS0_NOTCHIP3.1
!xsel:ASCA-SIS0-BRIGHT > extract spectrum
!xsel:ASCA-SIS0-BRIGHT > save spectrum spec2.tmp group=yes
Wrote spectrum to spec2.tmp
!xsel:ASCA-SIS0-BRIGHT > exit save_session=no
-> Fetching sis0c2p40_290296.fitsSisrmg Version 1.1, Configured 04/97 This version resolves *all* known keyword incompatibilities with other FTOOLS tasks. If you have previously fudged *any* keywords in the PHA file to compensate, incorrect results will follow. Setting 1st PHA channel to 0 Making v1.1 1180x512 S0C2 Bright PI RMF Calibration data from ./ Please stand by... ...Done.-> SIS0_NOTCHIP0.1 already present in current directory
** XSELECT V1.3 **
!> Enter session name >[xsel] xsel
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS S0CCDPOW
1 W50 EAST BRIGHT HIGH 27/04/93 23:50:32 0.34E+05 13416 1111
EXTRACTOR vers 2.0 11 Apr 1997.
Getting FITS WCS Keywords
Doing file: /data/data17/seq_proc/50006000.007/events.tmp
Total Good Bad: Region Time Phase Cut
13416 1774 11642 0 0 0
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
13416 1774 11642 0 0 0
in 33605.21 seconds
Spectrum has 1774 counts for 5.2789E-02 counts/sec
-------------------------
MANDATORY KEYWORDS/VALUES
-------------------------
--------------------------------------------------------------------
--------------------------------------------------------------------
EXTNAME - SPECTRUM Name of this BINTABLE
TELESCOP - ASCA Mission/Satellite name
INSTRUME - SIS0 Instrument/Detector
FILTER - Instrument filter in use
EXPOSURE - 33605. Integration time (in secs) of PHA data
AREASCAL - 1.0000 Area scaling factor
BACKSCAL - 6.98730E-02 Background scaling factor
BACKFILE - NONE Associated background file
CORRSCAL - 1.0000 Correlation scaling factor
CORRFILE - none Associated correlation file
RESPFILE - NONE Associated redistribution matrix file
ANCRFILE - none Associated ancillary response file
XFLT0001 - none XSPEC selection filter
POISSERR - TRUE Whether Poissonian errors apply
CHANTYPE - PI Whether channels have been corrected
TLMIN1 - 0 First legal Detector channel
DETCHANS - 512 No. of legal detector channels
NCHAN - 512 No. of detector channels in dataset
PHAVERSN - 1.1.0 OGIP FITS version number
STAT_ERR - FALSE Statistical Error
SYS_ERR - TRUE Fractional Systematic Error
QUALITY - TRUE Quality Flag
GROUPING - FALSE Grouping Flag
--------------------------------------------------------------------
--------------------------------------------------------------------
... QUALITY
...
... -------
... QUALITY
... -------
... Bad Channels (Channel - Channel)
... ---------------------------------------------
... 0 - 12 have quality 5
... ---------------------------------------------
...
...... exiting, changes written to file : spec3.tmp
Command not found; type ? for a command listing
!xsel:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!xsel:ASCA > set datadir .
Setting data directory to /data/data17/seq_proc/50006000.007/
Setting mkf directory to /data/data17/seq_proc/50006000.007/
!xsel:ASCA > read events events.tmp
Got new instrument: SIS0
Setting: IMAGE binning = 4
WMAP binning = 8
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 2047
Got the minimum time resolution of the read data: 16.000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data17/seq_proc/50006000.007/
HK Directory is: /data/data17/seq_proc/50006000.007/
!xsel:ASCA-SIS0-BRIGHT > set phaname PI
!xsel:ASCA-SIS0-BRIGHT > filter region ad50006000s032002_1.reg
!xsel:ASCA-SIS0-BRIGHT > filter region SIS0_OFFCHIP.1
!xsel:ASCA-SIS0-BRIGHT > filter region ad50006000s010102.discrim
!xsel:ASCA-SIS0-BRIGHT > filter region SIS0_NOTCHIP0.1
!xsel:ASCA-SIS0-BRIGHT > filter region SIS0_NOTCHIP1.1
!xsel:ASCA-SIS0-BRIGHT > filter region SIS0_NOTCHIP2.1
!xsel:ASCA-SIS0-BRIGHT > extract spectrum
!xsel:ASCA-SIS0-BRIGHT > save spectrum spec3.tmp group=yes
Wrote spectrum to spec3.tmp
!xsel:ASCA-SIS0-BRIGHT > exit save_session=no
-> Fetching sis0c3p40_290296.fitsSisrmg Version 1.1, Configured 04/97 This version resolves *all* known keyword incompatibilities with other FTOOLS tasks. If you have previously fudged *any* keywords in the PHA file to compensate, incorrect results will follow. Setting 1st PHA channel to 0 Making v1.1 1180x512 S0C3 Bright PI RMF Calibration data from ./ Please stand by... ...Done.-> Chip weights:
rmf0.tmp 0.561195587358378 rmf1.tmp 0.260062611806798 rmf2.tmp 0.0465116279069767 rmf3.tmp 0.132230172927847-> Standard Output From FTOOL addrmf:
ADDRMF vers 1.10 10 April, 1997.
Summing ...
5.612E-01 * rmf0.tmp
2.601E-01 * rmf1.tmp
4.651E-02 * rmf2.tmp
1.322E-01 * rmf3.tmp
RMF # 1 : rmf0.tmp 0.56
ASCA SIS0 NONE NONE PI
RMF # 2 : rmf1.tmp 0.26
ASCA SIS0 NONE NONE PI
RMF # 3 : rmf2.tmp 0.05
ASCA SIS0 NONE NONE PI
RMF # 4 : rmf3.tmp 0.13
ASCA SIS0 NONE NONE PI
-> Generating ad50006000s010102_1.arf with point=no
ASCAARF vers 2.72 14 Mar 1997.
Input WMAP array has size 82 by 100 bins
expanded to 82 by 100 bins
First WMAP bin is at detector pixel 224 416
8 detector pixels per WMAP bin
WMAP bin size is 0.21600 mm
0.21216 arcmin
Selected region size is 267.61 arcmin^2
Optical axis is detector pixel 662.72 559.02
1180 energies from RMF file
Effective area fudge applied
Arf filter applied
Total counts in region = 1.32340E+04
Weighted mean angle from optical axis = 7.988 arcmin
-> SIS0_NOTCHIP1.1 already present in current directoryad50006000s000302h.evt-> Standard Output From FTOOL xselect:
** XSELECT V1.3 **
!> Enter session name >[xsel] xsel
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS S0CCDPOW
1 W50 EAST BRIGHT HIGH 28/04/93 14:34:00 0.19E+04 1341 1011
EXTRACTOR vers 2.0 11 Apr 1997.
Getting FITS WCS Keywords
Doing file: /data/data17/seq_proc/50006000.007/ad50006000s000302h.evt
Total Good Bad: Region Time Phase Cut
1341 624 717 0 0 0
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
1341 624 717 0 0 0
in 1939.59 seconds
Spectrum has 624 counts for 0.3217 counts/sec
-------------------------
MANDATORY KEYWORDS/VALUES
-------------------------
--------------------------------------------------------------------
--------------------------------------------------------------------
EXTNAME - SPECTRUM Name of this BINTABLE
TELESCOP - ASCA Mission/Satellite name
INSTRUME - SIS0 Instrument/Detector
FILTER - Instrument filter in use
EXPOSURE - 1939.6 Integration time (in secs) of PHA data
AREASCAL - 1.0000 Area scaling factor
BACKSCAL - 0.18590 Background scaling factor
BACKFILE - NONE Associated background file
CORRSCAL - 1.0000 Correlation scaling factor
CORRFILE - none Associated correlation file
RESPFILE - NONE Associated redistribution matrix file
ANCRFILE - none Associated ancillary response file
XFLT0001 - none XSPEC selection filter
POISSERR - TRUE Whether Poissonian errors apply
CHANTYPE - PI Whether channels have been corrected
TLMIN1 - 0 First legal Detector channel
DETCHANS - 512 No. of legal detector channels
NCHAN - 512 No. of detector channels in dataset
PHAVERSN - 1.1.0 OGIP FITS version number
STAT_ERR - FALSE Statistical Error
SYS_ERR - TRUE Fractional Systematic Error
QUALITY - TRUE Quality Flag
GROUPING - FALSE Grouping Flag
--------------------------------------------------------------------
--------------------------------------------------------------------
... QUALITY
...
... -------
... QUALITY
... -------
... Bad Channels (Channel - Channel)
... ---------------------------------------------
... 0 - 12 have quality 5
... ---------------------------------------------
...
...... exiting, changes written to file : ad50006000s010202_1.pi
EXTRACTOR vers 2.0 11 Apr 1997.
Doing file: /data/data17/seq_proc/50006000.007/ad50006000s000302h.evt
Total Good Bad: Region Time Phase Cut
1341 624 717 0 0 0
Writing events file
624 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
1341 624 717 0 0 0
in 1939.59 seconds
Command not found; type ? for a command listing
!xsel:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!xsel:ASCA > set datadir .
Setting data directory to /data/data17/seq_proc/50006000.007/
Setting mkf directory to /data/data17/seq_proc/50006000.007/
!xsel:ASCA > read events ad50006000s000302h.evt
Got new instrument: SIS0
Setting: IMAGE binning = 4
WMAP binning = 8
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 2047
Got the minimum time resolution of the read data: 16.000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data17/seq_proc/50006000.007/
HK Directory is: /data/data17/seq_proc/50006000.007/
!xsel:ASCA-SIS0-BRIGHT > set phaname PI
!xsel:ASCA-SIS0-BRIGHT > filter region ad50006000s032002_1.reg
!xsel:ASCA-SIS0-BRIGHT > filter region SIS0_NOTCHIP1.1
!xsel:ASCA-SIS0-BRIGHT > filter region SIS0_OFFCHIP.1
!xsel:ASCA-SIS0-BRIGHT > filter region ad50006000s010202.discrim
!xsel:ASCA-SIS0-BRIGHT > extract spectrum
!xsel:ASCA-SIS0-BRIGHT > save spectrum ad50006000s010202_1.pi group=yes
Wrote spectrum to ad50006000s010202_1.pi
!xsel:ASCA-SIS0-BRIGHT > extract events
!xsel:ASCA-SIS0-BRIGHT > save events outfile=events.tmp use_events=yes
Wrote events list to file events.tmp
Changing Data directory from:
/data/data17/seq_proc/50006000.007/
to the current working directory.
!xsel:ASCA-SIS0-BRIGHT > exit save_session=no
-> Grouping ad50006000s010202_1.pi to 40 counts/bin------------------------- MANDATORY KEYWORDS/VALUES ------------------------- -------------------------------------------------------------------- -------------------------------------------------------------------- EXTNAME - SPECTRUM Name of this BINTABLE TELESCOP - ASCA Mission/Satellite name INSTRUME - SIS0 Instrument/Detector FILTER - Instrument filter in use EXPOSURE - 1939.6 Integration time (in secs) of PHA data AREASCAL - 1.0000 Area scaling factor BACKSCAL - 0.18590 Background scaling factor BACKFILE - NONE Associated background file CORRSCAL - 1.0000 Correlation scaling factor CORRFILE - none Associated correlation file RESPFILE - NONE Associated redistribution matrix file ANCRFILE - none Associated ancillary response file XFLT0001 - none XSPEC selection filter POISSERR - TRUE Whether Poissonian errors apply CHANTYPE - PI Whether channels have been corrected TLMIN1 - 0 First legal Detector channel DETCHANS - 512 No. of legal detector channels NCHAN - 512 No. of detector channels in dataset PHAVERSN - 1.1.0 OGIP FITS version number STAT_ERR - FALSE Statistical Error SYS_ERR - TRUE Fractional Systematic Error QUALITY - TRUE Quality Flag GROUPING - FALSE Grouping Flag -------------------------------------------------------------------- -------------------------------------------------------------------- ... ... -------- ... GROUPING ... -------- ... --------------------------------------------- ... Channel Grouping (Channel-Channel) : ... 0 - 12 of undefined grouping (Channel quality=bad) ... 13 - 26 are grouped by a factor 14 ... 27 - 32 are grouped by a factor 6 ... 33 - 36 are grouped by a factor 4 ... 37 - 43 are grouped by a factor 7 ... 44 - 48 are grouped by a factor 5 ... 49 - 52 are grouped by a factor 4 ... 53 - 59 are grouped by a factor 7 ... 60 - 70 are grouped by a factor 11 ... 71 - 102 are grouped by a factor 16 ... 103 - 126 are grouped by a factor 24 ... 127 - 165 are grouped by a factor 39 ... 166 - 218 are grouped by a factor 53 ... 219 - 473 are grouped by a factor 255 ... 474 - 511 of undefined grouping (Channel quality=bad) ... --------------------------------------------- ... ...... exiting, changes written to file : ad50006000s010202_1.pi ** grppha 2.6.0 completed successfully-> Source occupies chip(s) 0 2 3
** XSELECT V1.3 **
!> Enter session name >[xsel] xsel
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS S0CCDPOW
1 W50 EAST BRIGHT HIGH 28/04/93 14:34:00 0.19E+04 624 1011
EXTRACTOR vers 2.0 11 Apr 1997.
Getting FITS WCS Keywords
Doing file: /data/data17/seq_proc/50006000.007/events.tmp
Total Good Bad: Region Time Phase Cut
624 466 158 0 0 0
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
624 466 158 0 0 0
in 1939.59 seconds
Spectrum has 466 counts for 0.2403 counts/sec
-------------------------
MANDATORY KEYWORDS/VALUES
-------------------------
--------------------------------------------------------------------
--------------------------------------------------------------------
EXTNAME - SPECTRUM Name of this BINTABLE
TELESCOP - ASCA Mission/Satellite name
INSTRUME - SIS0 Instrument/Detector
FILTER - Instrument filter in use
EXPOSURE - 1939.6 Integration time (in secs) of PHA data
AREASCAL - 1.0000 Area scaling factor
BACKSCAL - 0.12253 Background scaling factor
BACKFILE - NONE Associated background file
CORRSCAL - 1.0000 Correlation scaling factor
CORRFILE - none Associated correlation file
RESPFILE - NONE Associated redistribution matrix file
ANCRFILE - none Associated ancillary response file
XFLT0001 - none XSPEC selection filter
POISSERR - TRUE Whether Poissonian errors apply
CHANTYPE - PI Whether channels have been corrected
TLMIN1 - 0 First legal Detector channel
DETCHANS - 512 No. of legal detector channels
NCHAN - 512 No. of detector channels in dataset
PHAVERSN - 1.1.0 OGIP FITS version number
STAT_ERR - FALSE Statistical Error
SYS_ERR - TRUE Fractional Systematic Error
QUALITY - TRUE Quality Flag
GROUPING - FALSE Grouping Flag
--------------------------------------------------------------------
--------------------------------------------------------------------
... QUALITY
...
... -------
... QUALITY
... -------
... Bad Channels (Channel - Channel)
... ---------------------------------------------
... 0 - 12 have quality 5
... ---------------------------------------------
...
...... exiting, changes written to file : spec0.tmp
Command not found; type ? for a command listing
!xsel:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!xsel:ASCA > set datadir .
Setting data directory to /data/data17/seq_proc/50006000.007/
Setting mkf directory to /data/data17/seq_proc/50006000.007/
!xsel:ASCA > read events events.tmp
Got new instrument: SIS0
Setting: IMAGE binning = 4
WMAP binning = 8
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 2047
Got the minimum time resolution of the read data: 16.000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data17/seq_proc/50006000.007/
HK Directory is: /data/data17/seq_proc/50006000.007/
!xsel:ASCA-SIS0-BRIGHT > set phaname PI
!xsel:ASCA-SIS0-BRIGHT > filter region ad50006000s032002_1.reg
!xsel:ASCA-SIS0-BRIGHT > filter region SIS0_NOTCHIP1.1
!xsel:ASCA-SIS0-BRIGHT > filter region SIS0_OFFCHIP.1
!xsel:ASCA-SIS0-BRIGHT > filter region ad50006000s010202.discrim
!xsel:ASCA-SIS0-BRIGHT > filter region SIS0_NOTCHIP2.1
!xsel:ASCA-SIS0-BRIGHT > filter region SIS0_NOTCHIP3.1
!xsel:ASCA-SIS0-BRIGHT > extract spectrum
!xsel:ASCA-SIS0-BRIGHT > save spectrum spec0.tmp group=yes
Wrote spectrum to spec0.tmp
!xsel:ASCA-SIS0-BRIGHT > exit save_session=no
-> sis0c0p40_290296.fits already present in current directorySisrmg Version 1.1, Configured 04/97 This version resolves *all* known keyword incompatibilities with other FTOOLS tasks. If you have previously fudged *any* keywords in the PHA file to compensate, incorrect results will follow. Setting 1st PHA channel to 0 Making v1.1 1180x512 S0C0 Bright PI RMF Calibration data from ./ Please stand by... ...Done.-> SIS0_NOTCHIP0.1 already present in current directory
** XSELECT V1.3 **
!> Enter session name >[xsel] xsel
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS S0CCDPOW
1 W50 EAST BRIGHT HIGH 28/04/93 14:34:00 0.19E+04 624 1011
EXTRACTOR vers 2.0 11 Apr 1997.
Getting FITS WCS Keywords
Doing file: /data/data17/seq_proc/50006000.007/events.tmp
Total Good Bad: Region Time Phase Cut
624 44 580 0 0 0
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
624 44 580 0 0 0
in 1939.59 seconds
Spectrum has 44 counts for 2.2685E-02 counts/sec
-------------------------
MANDATORY KEYWORDS/VALUES
-------------------------
--------------------------------------------------------------------
--------------------------------------------------------------------
EXTNAME - SPECTRUM Name of this BINTABLE
TELESCOP - ASCA Mission/Satellite name
INSTRUME - SIS0 Instrument/Detector
FILTER - Instrument filter in use
EXPOSURE - 1939.6 Integration time (in secs) of PHA data
AREASCAL - 1.0000 Area scaling factor
BACKSCAL - 2.93359E-02 Background scaling factor
BACKFILE - NONE Associated background file
CORRSCAL - 1.0000 Correlation scaling factor
CORRFILE - none Associated correlation file
RESPFILE - NONE Associated redistribution matrix file
ANCRFILE - none Associated ancillary response file
XFLT0001 - none XSPEC selection filter
POISSERR - TRUE Whether Poissonian errors apply
CHANTYPE - PI Whether channels have been corrected
TLMIN1 - 0 First legal Detector channel
DETCHANS - 512 No. of legal detector channels
NCHAN - 512 No. of detector channels in dataset
PHAVERSN - 1.1.0 OGIP FITS version number
STAT_ERR - FALSE Statistical Error
SYS_ERR - TRUE Fractional Systematic Error
QUALITY - TRUE Quality Flag
GROUPING - FALSE Grouping Flag
--------------------------------------------------------------------
--------------------------------------------------------------------
... QUALITY
...
... -------
... QUALITY
... -------
... Bad Channels (Channel - Channel)
... ---------------------------------------------
... 0 - 12 have quality 5
... ---------------------------------------------
...
...... exiting, changes written to file : spec2.tmp
Command not found; type ? for a command listing
!xsel:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!xsel:ASCA > set datadir .
Setting data directory to /data/data17/seq_proc/50006000.007/
Setting mkf directory to /data/data17/seq_proc/50006000.007/
!xsel:ASCA > read events events.tmp
Got new instrument: SIS0
Setting: IMAGE binning = 4
WMAP binning = 8
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 2047
Got the minimum time resolution of the read data: 16.000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data17/seq_proc/50006000.007/
HK Directory is: /data/data17/seq_proc/50006000.007/
!xsel:ASCA-SIS0-BRIGHT > set phaname PI
!xsel:ASCA-SIS0-BRIGHT > filter region ad50006000s032002_1.reg
!xsel:ASCA-SIS0-BRIGHT > filter region SIS0_NOTCHIP1.1
!xsel:ASCA-SIS0-BRIGHT > filter region SIS0_OFFCHIP.1
!xsel:ASCA-SIS0-BRIGHT > filter region ad50006000s010202.discrim
!xsel:ASCA-SIS0-BRIGHT > filter region SIS0_NOTCHIP0.1
!xsel:ASCA-SIS0-BRIGHT > filter region SIS0_NOTCHIP3.1
!xsel:ASCA-SIS0-BRIGHT > extract spectrum
!xsel:ASCA-SIS0-BRIGHT > save spectrum spec2.tmp group=yes
Wrote spectrum to spec2.tmp
!xsel:ASCA-SIS0-BRIGHT > exit save_session=no
-> sis0c2p40_290296.fits already present in current directorySisrmg Version 1.1, Configured 04/97 This version resolves *all* known keyword incompatibilities with other FTOOLS tasks. If you have previously fudged *any* keywords in the PHA file to compensate, incorrect results will follow. Setting 1st PHA channel to 0 Making v1.1 1180x512 S0C2 Bright PI RMF Calibration data from ./ Please stand by... ...Done.-> SIS0_NOTCHIP0.1 already present in current directory
** XSELECT V1.3 **
!> Enter session name >[xsel] xsel
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS S0CCDPOW
1 W50 EAST BRIGHT HIGH 28/04/93 14:34:00 0.19E+04 624 1011
EXTRACTOR vers 2.0 11 Apr 1997.
Getting FITS WCS Keywords
Doing file: /data/data17/seq_proc/50006000.007/events.tmp
Total Good Bad: Region Time Phase Cut
624 114 510 0 0 0
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
624 114 510 0 0 0
in 1939.59 seconds
Spectrum has 114 counts for 5.8775E-02 counts/sec
-------------------------
MANDATORY KEYWORDS/VALUES
-------------------------
--------------------------------------------------------------------
--------------------------------------------------------------------
EXTNAME - SPECTRUM Name of this BINTABLE
TELESCOP - ASCA Mission/Satellite name
INSTRUME - SIS0 Instrument/Detector
FILTER - Instrument filter in use
EXPOSURE - 1939.6 Integration time (in secs) of PHA data
AREASCAL - 1.0000 Area scaling factor
BACKSCAL - 6.98730E-02 Background scaling factor
BACKFILE - NONE Associated background file
CORRSCAL - 1.0000 Correlation scaling factor
CORRFILE - none Associated correlation file
RESPFILE - NONE Associated redistribution matrix file
ANCRFILE - none Associated ancillary response file
XFLT0001 - none XSPEC selection filter
POISSERR - TRUE Whether Poissonian errors apply
CHANTYPE - PI Whether channels have been corrected
TLMIN1 - 0 First legal Detector channel
DETCHANS - 512 No. of legal detector channels
NCHAN - 512 No. of detector channels in dataset
PHAVERSN - 1.1.0 OGIP FITS version number
STAT_ERR - FALSE Statistical Error
SYS_ERR - TRUE Fractional Systematic Error
QUALITY - TRUE Quality Flag
GROUPING - FALSE Grouping Flag
--------------------------------------------------------------------
--------------------------------------------------------------------
... QUALITY
...
... -------
... QUALITY
... -------
... Bad Channels (Channel - Channel)
... ---------------------------------------------
... 0 - 12 have quality 5
... ---------------------------------------------
...
...... exiting, changes written to file : spec3.tmp
Command not found; type ? for a command listing
!xsel:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!xsel:ASCA > set datadir .
Setting data directory to /data/data17/seq_proc/50006000.007/
Setting mkf directory to /data/data17/seq_proc/50006000.007/
!xsel:ASCA > read events events.tmp
Got new instrument: SIS0
Setting: IMAGE binning = 4
WMAP binning = 8
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 2047
Got the minimum time resolution of the read data: 16.000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data17/seq_proc/50006000.007/
HK Directory is: /data/data17/seq_proc/50006000.007/
!xsel:ASCA-SIS0-BRIGHT > set phaname PI
!xsel:ASCA-SIS0-BRIGHT > filter region ad50006000s032002_1.reg
!xsel:ASCA-SIS0-BRIGHT > filter region SIS0_NOTCHIP1.1
!xsel:ASCA-SIS0-BRIGHT > filter region SIS0_OFFCHIP.1
!xsel:ASCA-SIS0-BRIGHT > filter region ad50006000s010202.discrim
!xsel:ASCA-SIS0-BRIGHT > filter region SIS0_NOTCHIP0.1
!xsel:ASCA-SIS0-BRIGHT > filter region SIS0_NOTCHIP2.1
!xsel:ASCA-SIS0-BRIGHT > extract spectrum
!xsel:ASCA-SIS0-BRIGHT > save spectrum spec3.tmp group=yes
Wrote spectrum to spec3.tmp
!xsel:ASCA-SIS0-BRIGHT > exit save_session=no
-> sis0c3p40_290296.fits already present in current directorySisrmg Version 1.1, Configured 04/97 This version resolves *all* known keyword incompatibilities with other FTOOLS tasks. If you have previously fudged *any* keywords in the PHA file to compensate, incorrect results will follow. Setting 1st PHA channel to 0 Making v1.1 1180x512 S0C3 Bright PI RMF Calibration data from ./ Please stand by... ...Done.-> Chip weights:
rmf0.tmp 0.746794871794872 rmf2.tmp 0.0705128205128205 rmf3.tmp 0.182692307692308-> Standard Output From FTOOL addrmf:
ADDRMF vers 1.10 10 April, 1997.
Summing ...
7.468E-01 * rmf0.tmp
7.051E-02 * rmf2.tmp
1.827E-01 * rmf3.tmp
RMF # 1 : rmf0.tmp 0.75
ASCA SIS0 NONE NONE PI
RMF # 2 : rmf2.tmp 0.07
ASCA SIS0 NONE NONE PI
RMF # 3 : rmf3.tmp 0.18
ASCA SIS0 NONE NONE PI
-> Generating ad50006000s010202_1.arf with point=no
ASCAARF vers 2.72 14 Mar 1997.
Input WMAP array has size 81 by 95 bins
expanded to 81 by 95 bins
First WMAP bin is at detector pixel 224 456
8 detector pixels per WMAP bin
WMAP bin size is 0.21600 mm
0.21216 arcmin
Selected region size is 214.21 arcmin^2
Optical axis is detector pixel 662.72 559.02
1180 energies from RMF file
Effective area fudge applied
Arf filter applied
Total counts in region = 6.16000E+02
Weighted mean angle from optical axis = 9.088 arcmin
-> Standard Output From STOOL group_event_files:1 ad50006000s000112h.evt 11520 1 ad50006000s000612h.evt 11520 2 ad50006000s000312h.evt 1370-> SIS0_OFFCHIP.1 already present in current directory
ad50006000s000112h.evt ad50006000s000612h.evt-> Standard Output From FTOOL xselect:
** XSELECT V1.3 **
!> Enter session name >[xsel] xsel
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS S0CCDPOW
1 W50 EAST BRIGHT2 HIGH 28/04/93 03:44:28 0.16E+05 10514 1111
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS S0CCDPOW
1 W50 EAST BRIGHT2 HIGH 28/04/93 03:44:28 0.16E+05 10514 1111
2 W50 EAST BRIGHT2 HIGH 28/04/93 22:52:12 0.15E+04 1006 1111
EXTRACTOR vers 2.0 11 Apr 1997.
Getting FITS WCS Keywords
Doing file: /data/data17/seq_proc/50006000.007/ad50006000s000112h.evt
Total Good Bad: Region Time Phase Cut
10514 6416 4098 0 0 0
Doing file: /data/data17/seq_proc/50006000.007/ad50006000s000612h.evt
Total Good Bad: Region Time Phase Cut
1006 628 378 0 0 0
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
11520 7044 4476 0 0 0
in 17022.75 seconds
Spectrum has 7044 counts for 0.4138 counts/sec
-------------------------
MANDATORY KEYWORDS/VALUES
-------------------------
--------------------------------------------------------------------
--------------------------------------------------------------------
EXTNAME - SPECTRUM Name of this BINTABLE
TELESCOP - ASCA Mission/Satellite name
INSTRUME - SIS0 Instrument/Detector
FILTER - Instrument filter in use
EXPOSURE - 17023. Integration time (in secs) of PHA data
AREASCAL - 1.0000 Area scaling factor
BACKSCAL - 0.23224 Background scaling factor
BACKFILE - NONE Associated background file
CORRSCAL - 1.0000 Correlation scaling factor
CORRFILE - none Associated correlation file
RESPFILE - NONE Associated redistribution matrix file
ANCRFILE - none Associated ancillary response file
XFLT0001 - none XSPEC selection filter
POISSERR - TRUE Whether Poissonian errors apply
CHANTYPE - PI Whether channels have been corrected
TLMIN1 - 0 First legal Detector channel
DETCHANS - 1024 No. of legal detector channels
NCHAN - 1024 No. of detector channels in dataset
PHAVERSN - 1.1.0 OGIP FITS version number
STAT_ERR - FALSE Statistical Error
SYS_ERR - TRUE Fractional Systematic Error
QUALITY - TRUE Quality Flag
GROUPING - FALSE Grouping Flag
--------------------------------------------------------------------
--------------------------------------------------------------------
... QUALITY
...
... -------
... QUALITY
... -------
... Bad Channels (Channel - Channel)
... ---------------------------------------------
... 0 - 25 have quality 5
... ---------------------------------------------
...
...... exiting, changes written to file : ad50006000s010312_1.pi
EXTRACTOR vers 2.0 11 Apr 1997.
Doing file: /data/data17/seq_proc/50006000.007/ad50006000s000112h.evt
Total Good Bad: Region Time Phase Cut
10514 6416 4098 0 0 0
Writing events file
6416 events written to the output file
Doing file: /data/data17/seq_proc/50006000.007/ad50006000s000612h.evt
Total Good Bad: Region Time Phase Cut
1006 628 378 0 0 0
Writing events file
7044 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
11520 7044 4476 0 0 0
in 17022.75 seconds
Command not found; type ? for a command listing
!xsel:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!xsel:ASCA > set datadir .
Setting data directory to /data/data17/seq_proc/50006000.007/
Setting mkf directory to /data/data17/seq_proc/50006000.007/
!xsel:ASCA > read events ad50006000s000112h.evt
Got new instrument: SIS0
Setting: IMAGE binning = 4
WMAP binning = 8
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 4095
Got the minimum time resolution of the read data: 16.000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data17/seq_proc/50006000.007/
HK Directory is: /data/data17/seq_proc/50006000.007/
!xsel:ASCA-SIS0-BRIGHT2 > read events ad50006000s000612h.evt
Getting Min and Max for Energy Column...
Got min and max for PI: 0 4095
Got the minimum time resolution of the read data: 16.000
Number of files read in: 2
******************** Observation Catalogue ********************
Data Directory is: /data/data17/seq_proc/50006000.007/
HK Directory is: /data/data17/seq_proc/50006000.007/
!xsel:ASCA-SIS0-BRIGHT2 > set phaname PI
!xsel:ASCA-SIS0-BRIGHT2 > filter region ad50006000s032002_1.reg
!xsel:ASCA-SIS0-BRIGHT2 > filter region SIS0_OFFCHIP.1
!xsel:ASCA-SIS0-BRIGHT2 > filter region ad50006000s010312.discrim
!xsel:ASCA-SIS0-BRIGHT2 > extract spectrum
!xsel:ASCA-SIS0-BRIGHT2 > save spectrum ad50006000s010312_1.pi group=yes
Wrote spectrum to ad50006000s010312_1.pi
!xsel:ASCA-SIS0-BRIGHT2 > extract events
!xsel:ASCA-SIS0-BRIGHT2 > save events outfile=events.tmp use_events=yes
Wrote events list to file events.tmp
Changing Data directory from:
/data/data17/seq_proc/50006000.007/
to the current working directory.
!xsel:ASCA-SIS0-BRIGHT2 > exit save_session=no
-> Grouping ad50006000s010312_1.pi to 40 counts/bin------------------------- MANDATORY KEYWORDS/VALUES ------------------------- -------------------------------------------------------------------- -------------------------------------------------------------------- EXTNAME - SPECTRUM Name of this BINTABLE TELESCOP - ASCA Mission/Satellite name INSTRUME - SIS0 Instrument/Detector FILTER - Instrument filter in use EXPOSURE - 17023. Integration time (in secs) of PHA data AREASCAL - 1.0000 Area scaling factor BACKSCAL - 0.23224 Background scaling factor BACKFILE - NONE Associated background file CORRSCAL - 1.0000 Correlation scaling factor CORRFILE - none Associated correlation file RESPFILE - NONE Associated redistribution matrix file ANCRFILE - none Associated ancillary response file XFLT0001 - none XSPEC selection filter POISSERR - TRUE Whether Poissonian errors apply CHANTYPE - PI Whether channels have been corrected TLMIN1 - 0 First legal Detector channel DETCHANS - 1024 No. of legal detector channels NCHAN - 1024 No. of detector channels in dataset PHAVERSN - 1.1.0 OGIP FITS version number STAT_ERR - FALSE Statistical Error SYS_ERR - TRUE Fractional Systematic Error QUALITY - TRUE Quality Flag GROUPING - FALSE Grouping Flag -------------------------------------------------------------------- -------------------------------------------------------------------- ... ... -------- ... GROUPING ... -------- ... --------------------------------------------- ... Channel Grouping (Channel-Channel) : ... 0 - 25 of undefined grouping (Channel quality=bad) ... 26 - 28 are grouped by a factor 3 ... 29 - 36 are grouped by a factor 4 ... 37 - 39 are grouped by a factor 3 ... 40 - 43 are grouped by a factor 4 ... 44 - 49 are grouped by a factor 3 ... 50 - 55 are grouped by a factor 2 ... 56 - 57 are single channels ... 58 - 59 are grouped by a factor 2 ... 60 - 60 are single channels ... 61 - 62 are grouped by a factor 2 ... 63 - 66 are single channels ... 67 - 68 are grouped by a factor 2 ... 69 - 75 are single channels ... 76 - 77 are grouped by a factor 2 ... 78 - 82 are single channels ... 83 - 84 are grouped by a factor 2 ... 85 - 85 are single channels ... 86 - 87 are grouped by a factor 2 ... 88 - 103 are single channels ... 104 - 105 are grouped by a factor 2 ... 106 - 106 are single channels ... 107 - 108 are grouped by a factor 2 ... 109 - 109 are single channels ... 110 - 147 are grouped by a factor 2 ... 148 - 150 are grouped by a factor 3 ... 151 - 154 are grouped by a factor 2 ... 155 - 162 are grouped by a factor 4 ... 163 - 174 are grouped by a factor 3 ... 175 - 182 are grouped by a factor 4 ... 183 - 185 are grouped by a factor 3 ... 186 - 189 are grouped by a factor 4 ... 190 - 192 are grouped by a factor 3 ... 193 - 204 are grouped by a factor 4 ... 205 - 209 are grouped by a factor 5 ... 210 - 213 are grouped by a factor 4 ... 214 - 216 are grouped by a factor 3 ... 217 - 221 are grouped by a factor 5 ... 222 - 225 are grouped by a factor 4 ... 226 - 230 are grouped by a factor 5 ... 231 - 238 are grouped by a factor 4 ... 239 - 243 are grouped by a factor 5 ... 244 - 249 are grouped by a factor 6 ... 250 - 254 are grouped by a factor 5 ... 255 - 258 are grouped by a factor 4 ... 259 - 272 are grouped by a factor 7 ... 273 - 278 are grouped by a factor 6 ... 279 - 286 are grouped by a factor 8 ... 287 - 293 are grouped by a factor 7 ... 294 - 299 are grouped by a factor 6 ... 300 - 309 are grouped by a factor 10 ... 310 - 318 are grouped by a factor 9 ... 319 - 325 are grouped by a factor 7 ... 326 - 333 are grouped by a factor 8 ... 334 - 343 are grouped by a factor 10 ... 344 - 357 are grouped by a factor 14 ... 358 - 369 are grouped by a factor 12 ... 370 - 379 are grouped by a factor 10 ... 380 - 396 are grouped by a factor 17 ... 397 - 417 are grouped by a factor 21 ... 418 - 440 are grouped by a factor 23 ... 441 - 478 are grouped by a factor 38 ... 479 - 507 are grouped by a factor 29 ... 508 - 555 are grouped by a factor 48 ... 556 - 624 are grouped by a factor 69 ... 625 - 701 are grouped by a factor 77 ... 702 - 780 are grouped by a factor 79 ... 781 - 871 are grouped by a factor 91 ... 872 - 910 are grouped by a factor 39 ... 911 - 922 are grouped by a factor 12 ... 923 - 933 are grouped by a factor 11 ... 934 - 945 are grouped by a factor 12 ... 946 - 956 are grouped by a factor 11 ... 957 - 970 are grouped by a factor 14 ... --------------------------------------------- ... ...... exiting, changes written to file : ad50006000s010312_1.pi ** grppha 2.6.0 completed successfully-> Source occupies chip(s) 0 1 2 3
** XSELECT V1.3 **
!> Enter session name >[xsel] xsel
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS S0CCDPOW
1 W50 EAST BRIGHT2 HIGH 28/04/93 03:44:28 0.17E+05 7044 1111
EXTRACTOR vers 2.0 11 Apr 1997.
Getting FITS WCS Keywords
Doing file: /data/data17/seq_proc/50006000.007/events.tmp
Total Good Bad: Region Time Phase Cut
7044 3904 3140 0 0 0
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
7044 3904 3140 0 0 0
in 17022.75 seconds
Spectrum has 3904 counts for 0.2293 counts/sec
-------------------------
MANDATORY KEYWORDS/VALUES
-------------------------
--------------------------------------------------------------------
--------------------------------------------------------------------
EXTNAME - SPECTRUM Name of this BINTABLE
TELESCOP - ASCA Mission/Satellite name
INSTRUME - SIS0 Instrument/Detector
FILTER - Instrument filter in use
EXPOSURE - 17023. Integration time (in secs) of PHA data
AREASCAL - 1.0000 Area scaling factor
BACKSCAL - 0.12253 Background scaling factor
BACKFILE - NONE Associated background file
CORRSCAL - 1.0000 Correlation scaling factor
CORRFILE - none Associated correlation file
RESPFILE - NONE Associated redistribution matrix file
ANCRFILE - none Associated ancillary response file
XFLT0001 - none XSPEC selection filter
POISSERR - TRUE Whether Poissonian errors apply
CHANTYPE - PI Whether channels have been corrected
TLMIN1 - 0 First legal Detector channel
DETCHANS - 1024 No. of legal detector channels
NCHAN - 1024 No. of detector channels in dataset
PHAVERSN - 1.1.0 OGIP FITS version number
STAT_ERR - FALSE Statistical Error
SYS_ERR - TRUE Fractional Systematic Error
QUALITY - TRUE Quality Flag
GROUPING - FALSE Grouping Flag
--------------------------------------------------------------------
--------------------------------------------------------------------
... QUALITY
...
... -------
... QUALITY
... -------
... Bad Channels (Channel - Channel)
... ---------------------------------------------
... 0 - 25 have quality 5
... ---------------------------------------------
...
...... exiting, changes written to file : spec0.tmp
Command not found; type ? for a command listing
!xsel:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!xsel:ASCA > set datadir .
Setting data directory to /data/data17/seq_proc/50006000.007/
Setting mkf directory to /data/data17/seq_proc/50006000.007/
!xsel:ASCA > read events events.tmp
Got new instrument: SIS0
Setting: IMAGE binning = 4
WMAP binning = 8
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 4095
Got the minimum time resolution of the read data: 16.000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data17/seq_proc/50006000.007/
HK Directory is: /data/data17/seq_proc/50006000.007/
!xsel:ASCA-SIS0-BRIGHT2 > set phaname PI
!xsel:ASCA-SIS0-BRIGHT2 > filter region ad50006000s032002_1.reg
!xsel:ASCA-SIS0-BRIGHT2 > filter region SIS0_OFFCHIP.1
!xsel:ASCA-SIS0-BRIGHT2 > filter region ad50006000s010312.discrim
!xsel:ASCA-SIS0-BRIGHT2 > filter region SIS0_NOTCHIP1.1
!xsel:ASCA-SIS0-BRIGHT2 > filter region SIS0_NOTCHIP2.1
!xsel:ASCA-SIS0-BRIGHT2 > filter region SIS0_NOTCHIP3.1
!xsel:ASCA-SIS0-BRIGHT2 > extract spectrum
!xsel:ASCA-SIS0-BRIGHT2 > save spectrum spec0.tmp group=yes
Wrote spectrum to spec0.tmp
!xsel:ASCA-SIS0-BRIGHT2 > exit save_session=no
-> sis0c0p40_290296.fits already present in current directorySisrmg Version 1.1, Configured 04/97 This version resolves *all* known keyword incompatibilities with other FTOOLS tasks. If you have previously fudged *any* keywords in the PHA file to compensate, incorrect results will follow. Setting 1st PHA channel to 0 Making v1.1 1180x1024 S0C0 Bright2 PI RMF Calibration data from ./ Please stand by... ...Done.-> SIS0_NOTCHIP0.1 already present in current directory
** XSELECT V1.3 **
!> Enter session name >[xsel] xsel
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS S0CCDPOW
1 W50 EAST BRIGHT2 HIGH 28/04/93 03:44:28 0.17E+05 7044 1111
EXTRACTOR vers 2.0 11 Apr 1997.
Getting FITS WCS Keywords
Doing file: /data/data17/seq_proc/50006000.007/events.tmp
Total Good Bad: Region Time Phase Cut
7044 1890 5154 0 0 0
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
7044 1890 5154 0 0 0
in 17022.75 seconds
Spectrum has 1890 counts for 0.1110 counts/sec
-------------------------
MANDATORY KEYWORDS/VALUES
-------------------------
--------------------------------------------------------------------
--------------------------------------------------------------------
EXTNAME - SPECTRUM Name of this BINTABLE
TELESCOP - ASCA Mission/Satellite name
INSTRUME - SIS0 Instrument/Detector
FILTER - Instrument filter in use
EXPOSURE - 17023. Integration time (in secs) of PHA data
AREASCAL - 1.0000 Area scaling factor
BACKSCAL - 6.42578E-02 Background scaling factor
BACKFILE - NONE Associated background file
CORRSCAL - 1.0000 Correlation scaling factor
CORRFILE - none Associated correlation file
RESPFILE - NONE Associated redistribution matrix file
ANCRFILE - none Associated ancillary response file
XFLT0001 - none XSPEC selection filter
POISSERR - TRUE Whether Poissonian errors apply
CHANTYPE - PI Whether channels have been corrected
TLMIN1 - 0 First legal Detector channel
DETCHANS - 1024 No. of legal detector channels
NCHAN - 1024 No. of detector channels in dataset
PHAVERSN - 1.1.0 OGIP FITS version number
STAT_ERR - FALSE Statistical Error
SYS_ERR - TRUE Fractional Systematic Error
QUALITY - TRUE Quality Flag
GROUPING - FALSE Grouping Flag
--------------------------------------------------------------------
--------------------------------------------------------------------
... QUALITY
...
... -------
... QUALITY
... -------
... Bad Channels (Channel - Channel)
... ---------------------------------------------
... 0 - 25 have quality 5
... ---------------------------------------------
...
...... exiting, changes written to file : spec1.tmp
Command not found; type ? for a command listing
!xsel:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!xsel:ASCA > set datadir .
Setting data directory to /data/data17/seq_proc/50006000.007/
Setting mkf directory to /data/data17/seq_proc/50006000.007/
!xsel:ASCA > read events events.tmp
Got new instrument: SIS0
Setting: IMAGE binning = 4
WMAP binning = 8
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 4095
Got the minimum time resolution of the read data: 16.000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data17/seq_proc/50006000.007/
HK Directory is: /data/data17/seq_proc/50006000.007/
!xsel:ASCA-SIS0-BRIGHT2 > set phaname PI
!xsel:ASCA-SIS0-BRIGHT2 > filter region ad50006000s032002_1.reg
!xsel:ASCA-SIS0-BRIGHT2 > filter region SIS0_OFFCHIP.1
!xsel:ASCA-SIS0-BRIGHT2 > filter region ad50006000s010312.discrim
!xsel:ASCA-SIS0-BRIGHT2 > filter region SIS0_NOTCHIP0.1
!xsel:ASCA-SIS0-BRIGHT2 > filter region SIS0_NOTCHIP2.1
!xsel:ASCA-SIS0-BRIGHT2 > filter region SIS0_NOTCHIP3.1
!xsel:ASCA-SIS0-BRIGHT2 > extract spectrum
!xsel:ASCA-SIS0-BRIGHT2 > save spectrum spec1.tmp group=yes
Wrote spectrum to spec1.tmp
!xsel:ASCA-SIS0-BRIGHT2 > exit save_session=no
-> sis0c1p40_290296.fits already present in current directorySisrmg Version 1.1, Configured 04/97 This version resolves *all* known keyword incompatibilities with other FTOOLS tasks. If you have previously fudged *any* keywords in the PHA file to compensate, incorrect results will follow. Setting 1st PHA channel to 0 Making v1.1 1180x1024 S0C1 Bright2 PI RMF Calibration data from ./ Please stand by... ...Done.-> SIS0_NOTCHIP0.1 already present in current directory
** XSELECT V1.3 **
!> Enter session name >[xsel] xsel
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS S0CCDPOW
1 W50 EAST BRIGHT2 HIGH 28/04/93 03:44:28 0.17E+05 7044 1111
EXTRACTOR vers 2.0 11 Apr 1997.
Getting FITS WCS Keywords
Doing file: /data/data17/seq_proc/50006000.007/events.tmp
Total Good Bad: Region Time Phase Cut
7044 330 6714 0 0 0
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
7044 330 6714 0 0 0
in 17022.75 seconds
Spectrum has 330 counts for 1.9386E-02 counts/sec
-------------------------
MANDATORY KEYWORDS/VALUES
-------------------------
--------------------------------------------------------------------
--------------------------------------------------------------------
EXTNAME - SPECTRUM Name of this BINTABLE
TELESCOP - ASCA Mission/Satellite name
INSTRUME - SIS0 Instrument/Detector
FILTER - Instrument filter in use
EXPOSURE - 17023. Integration time (in secs) of PHA data
AREASCAL - 1.0000 Area scaling factor
BACKSCAL - 2.93359E-02 Background scaling factor
BACKFILE - NONE Associated background file
CORRSCAL - 1.0000 Correlation scaling factor
CORRFILE - none Associated correlation file
RESPFILE - NONE Associated redistribution matrix file
ANCRFILE - none Associated ancillary response file
XFLT0001 - none XSPEC selection filter
POISSERR - TRUE Whether Poissonian errors apply
CHANTYPE - PI Whether channels have been corrected
TLMIN1 - 0 First legal Detector channel
DETCHANS - 1024 No. of legal detector channels
NCHAN - 1024 No. of detector channels in dataset
PHAVERSN - 1.1.0 OGIP FITS version number
STAT_ERR - FALSE Statistical Error
SYS_ERR - TRUE Fractional Systematic Error
QUALITY - TRUE Quality Flag
GROUPING - FALSE Grouping Flag
--------------------------------------------------------------------
--------------------------------------------------------------------
... QUALITY
...
... -------
... QUALITY
... -------
... Bad Channels (Channel - Channel)
... ---------------------------------------------
... 0 - 25 have quality 5
... ---------------------------------------------
...
...... exiting, changes written to file : spec2.tmp
Command not found; type ? for a command listing
!xsel:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!xsel:ASCA > set datadir .
Setting data directory to /data/data17/seq_proc/50006000.007/
Setting mkf directory to /data/data17/seq_proc/50006000.007/
!xsel:ASCA > read events events.tmp
Got new instrument: SIS0
Setting: IMAGE binning = 4
WMAP binning = 8
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 4095
Got the minimum time resolution of the read data: 16.000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data17/seq_proc/50006000.007/
HK Directory is: /data/data17/seq_proc/50006000.007/
!xsel:ASCA-SIS0-BRIGHT2 > set phaname PI
!xsel:ASCA-SIS0-BRIGHT2 > filter region ad50006000s032002_1.reg
!xsel:ASCA-SIS0-BRIGHT2 > filter region SIS0_OFFCHIP.1
!xsel:ASCA-SIS0-BRIGHT2 > filter region ad50006000s010312.discrim
!xsel:ASCA-SIS0-BRIGHT2 > filter region SIS0_NOTCHIP0.1
!xsel:ASCA-SIS0-BRIGHT2 > filter region SIS0_NOTCHIP1.1
!xsel:ASCA-SIS0-BRIGHT2 > filter region SIS0_NOTCHIP3.1
!xsel:ASCA-SIS0-BRIGHT2 > extract spectrum
!xsel:ASCA-SIS0-BRIGHT2 > save spectrum spec2.tmp group=yes
Wrote spectrum to spec2.tmp
!xsel:ASCA-SIS0-BRIGHT2 > exit save_session=no
-> sis0c2p40_290296.fits already present in current directorySisrmg Version 1.1, Configured 04/97 This version resolves *all* known keyword incompatibilities with other FTOOLS tasks. If you have previously fudged *any* keywords in the PHA file to compensate, incorrect results will follow. Setting 1st PHA channel to 0 Making v1.1 1180x1024 S0C2 Bright2 PI RMF Calibration data from ./ Please stand by... ...Done.-> SIS0_NOTCHIP0.1 already present in current directory
** XSELECT V1.3 **
!> Enter session name >[xsel] xsel
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS S0CCDPOW
1 W50 EAST BRIGHT2 HIGH 28/04/93 03:44:28 0.17E+05 7044 1111
EXTRACTOR vers 2.0 11 Apr 1997.
Getting FITS WCS Keywords
Doing file: /data/data17/seq_proc/50006000.007/events.tmp
Total Good Bad: Region Time Phase Cut
7044 920 6124 0 0 0
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
7044 920 6124 0 0 0
in 17022.75 seconds
Spectrum has 920 counts for 5.4045E-02 counts/sec
-------------------------
MANDATORY KEYWORDS/VALUES
-------------------------
--------------------------------------------------------------------
--------------------------------------------------------------------
EXTNAME - SPECTRUM Name of this BINTABLE
TELESCOP - ASCA Mission/Satellite name
INSTRUME - SIS0 Instrument/Detector
FILTER - Instrument filter in use
EXPOSURE - 17023. Integration time (in secs) of PHA data
AREASCAL - 1.0000 Area scaling factor
BACKSCAL - 6.98730E-02 Background scaling factor
BACKFILE - NONE Associated background file
CORRSCAL - 1.0000 Correlation scaling factor
CORRFILE - none Associated correlation file
RESPFILE - NONE Associated redistribution matrix file
ANCRFILE - none Associated ancillary response file
XFLT0001 - none XSPEC selection filter
POISSERR - TRUE Whether Poissonian errors apply
CHANTYPE - PI Whether channels have been corrected
TLMIN1 - 0 First legal Detector channel
DETCHANS - 1024 No. of legal detector channels
NCHAN - 1024 No. of detector channels in dataset
PHAVERSN - 1.1.0 OGIP FITS version number
STAT_ERR - FALSE Statistical Error
SYS_ERR - TRUE Fractional Systematic Error
QUALITY - TRUE Quality Flag
GROUPING - FALSE Grouping Flag
--------------------------------------------------------------------
--------------------------------------------------------------------
... QUALITY
...
... -------
... QUALITY
... -------
... Bad Channels (Channel - Channel)
... ---------------------------------------------
... 0 - 25 have quality 5
... ---------------------------------------------
...
...... exiting, changes written to file : spec3.tmp
Command not found; type ? for a command listing
!xsel:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!xsel:ASCA > set datadir .
Setting data directory to /data/data17/seq_proc/50006000.007/
Setting mkf directory to /data/data17/seq_proc/50006000.007/
!xsel:ASCA > read events events.tmp
Got new instrument: SIS0
Setting: IMAGE binning = 4
WMAP binning = 8
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 4095
Got the minimum time resolution of the read data: 16.000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data17/seq_proc/50006000.007/
HK Directory is: /data/data17/seq_proc/50006000.007/
!xsel:ASCA-SIS0-BRIGHT2 > set phaname PI
!xsel:ASCA-SIS0-BRIGHT2 > filter region ad50006000s032002_1.reg
!xsel:ASCA-SIS0-BRIGHT2 > filter region SIS0_OFFCHIP.1
!xsel:ASCA-SIS0-BRIGHT2 > filter region ad50006000s010312.discrim
!xsel:ASCA-SIS0-BRIGHT2 > filter region SIS0_NOTCHIP0.1
!xsel:ASCA-SIS0-BRIGHT2 > filter region SIS0_NOTCHIP1.1
!xsel:ASCA-SIS0-BRIGHT2 > filter region SIS0_NOTCHIP2.1
!xsel:ASCA-SIS0-BRIGHT2 > extract spectrum
!xsel:ASCA-SIS0-BRIGHT2 > save spectrum spec3.tmp group=yes
Wrote spectrum to spec3.tmp
!xsel:ASCA-SIS0-BRIGHT2 > exit save_session=no
-> sis0c3p40_290296.fits already present in current directorySisrmg Version 1.1, Configured 04/97 This version resolves *all* known keyword incompatibilities with other FTOOLS tasks. If you have previously fudged *any* keywords in the PHA file to compensate, incorrect results will follow. Setting 1st PHA channel to 0 Making v1.1 1180x1024 S0C3 Bright2 PI RMF Calibration data from ./ Please stand by... ...Done.-> Chip weights:
rmf0.tmp 0.554230550823396 rmf1.tmp 0.268313458262351 rmf2.tmp 0.0468483816013629 rmf3.tmp 0.13060760931289-> Standard Output From FTOOL addrmf:
ADDRMF vers 1.10 10 April, 1997.
Summing ...
5.542E-01 * rmf0.tmp
2.683E-01 * rmf1.tmp
4.685E-02 * rmf2.tmp
1.306E-01 * rmf3.tmp
RMF # 1 : rmf0.tmp 0.55
ASCA SIS0 NONE NONE PI
RMF # 2 : rmf1.tmp 0.27
ASCA SIS0 NONE NONE PI
RMF # 3 : rmf2.tmp 0.05
ASCA SIS0 NONE NONE PI
RMF # 4 : rmf3.tmp 0.13
ASCA SIS0 NONE NONE PI
-> Generating ad50006000s010312_1.arf with point=no
ASCAARF vers 2.72 14 Mar 1997.
Input WMAP array has size 82 by 100 bins
expanded to 82 by 100 bins
First WMAP bin is at detector pixel 224 416
8 detector pixels per WMAP bin
WMAP bin size is 0.21600 mm
0.21216 arcmin
Selected region size is 267.61 arcmin^2
Optical axis is detector pixel 662.72 559.02
1180 energies from RMF file
Effective area fudge applied
Arf filter applied
Total counts in region = 6.91200E+03
Weighted mean angle from optical axis = 7.928 arcmin
-> SIS0_NOTCHIP1.1 already present in current directoryad50006000s000312h.evt-> Standard Output From FTOOL xselect:
** XSELECT V1.3 **
!> Enter session name >[xsel] xsel
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS S0CCDPOW
1 W50 EAST BRIGHT2 HIGH 28/04/93 14:34:00 0.19E+04 1370 1011
EXTRACTOR vers 2.0 11 Apr 1997.
Getting FITS WCS Keywords
Doing file: /data/data17/seq_proc/50006000.007/ad50006000s000312h.evt
Total Good Bad: Region Time Phase Cut
1370 642 728 0 0 0
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
1370 642 728 0 0 0
in 1939.59 seconds
Spectrum has 642 counts for 0.3310 counts/sec
-------------------------
MANDATORY KEYWORDS/VALUES
-------------------------
--------------------------------------------------------------------
--------------------------------------------------------------------
EXTNAME - SPECTRUM Name of this BINTABLE
TELESCOP - ASCA Mission/Satellite name
INSTRUME - SIS0 Instrument/Detector
FILTER - Instrument filter in use
EXPOSURE - 1939.6 Integration time (in secs) of PHA data
AREASCAL - 1.0000 Area scaling factor
BACKSCAL - 0.18590 Background scaling factor
BACKFILE - NONE Associated background file
CORRSCAL - 1.0000 Correlation scaling factor
CORRFILE - none Associated correlation file
RESPFILE - NONE Associated redistribution matrix file
ANCRFILE - none Associated ancillary response file
XFLT0001 - none XSPEC selection filter
POISSERR - TRUE Whether Poissonian errors apply
CHANTYPE - PI Whether channels have been corrected
TLMIN1 - 0 First legal Detector channel
DETCHANS - 1024 No. of legal detector channels
NCHAN - 1024 No. of detector channels in dataset
PHAVERSN - 1.1.0 OGIP FITS version number
STAT_ERR - FALSE Statistical Error
SYS_ERR - TRUE Fractional Systematic Error
QUALITY - TRUE Quality Flag
GROUPING - FALSE Grouping Flag
--------------------------------------------------------------------
--------------------------------------------------------------------
... QUALITY
...
... -------
... QUALITY
... -------
... Bad Channels (Channel - Channel)
... ---------------------------------------------
... 0 - 25 have quality 5
... ---------------------------------------------
...
...... exiting, changes written to file : ad50006000s010412_1.pi
EXTRACTOR vers 2.0 11 Apr 1997.
Doing file: /data/data17/seq_proc/50006000.007/ad50006000s000312h.evt
Total Good Bad: Region Time Phase Cut
1370 642 728 0 0 0
Writing events file
642 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
1370 642 728 0 0 0
in 1939.59 seconds
Command not found; type ? for a command listing
!xsel:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!xsel:ASCA > set datadir .
Setting data directory to /data/data17/seq_proc/50006000.007/
Setting mkf directory to /data/data17/seq_proc/50006000.007/
!xsel:ASCA > read events ad50006000s000312h.evt
Got new instrument: SIS0
Setting: IMAGE binning = 4
WMAP binning = 8
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 4095
Got the minimum time resolution of the read data: 16.000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data17/seq_proc/50006000.007/
HK Directory is: /data/data17/seq_proc/50006000.007/
!xsel:ASCA-SIS0-BRIGHT2 > set phaname PI
!xsel:ASCA-SIS0-BRIGHT2 > filter region ad50006000s032002_1.reg
!xsel:ASCA-SIS0-BRIGHT2 > filter region SIS0_NOTCHIP1.1
!xsel:ASCA-SIS0-BRIGHT2 > filter region SIS0_OFFCHIP.1
!xsel:ASCA-SIS0-BRIGHT2 > filter region ad50006000s010412.discrim
!xsel:ASCA-SIS0-BRIGHT2 > extract spectrum
!xsel:ASCA-SIS0-BRIGHT2 > save spectrum ad50006000s010412_1.pi group=yes
Wrote spectrum to ad50006000s010412_1.pi
!xsel:ASCA-SIS0-BRIGHT2 > extract events
!xsel:ASCA-SIS0-BRIGHT2 > save events outfile=events.tmp use_events=yes
Wrote events list to file events.tmp
Changing Data directory from:
/data/data17/seq_proc/50006000.007/
to the current working directory.
!xsel:ASCA-SIS0-BRIGHT2 > exit save_session=no
-> Grouping ad50006000s010412_1.pi to 40 counts/bin------------------------- MANDATORY KEYWORDS/VALUES ------------------------- -------------------------------------------------------------------- -------------------------------------------------------------------- EXTNAME - SPECTRUM Name of this BINTABLE TELESCOP - ASCA Mission/Satellite name INSTRUME - SIS0 Instrument/Detector FILTER - Instrument filter in use EXPOSURE - 1939.6 Integration time (in secs) of PHA data AREASCAL - 1.0000 Area scaling factor BACKSCAL - 0.18590 Background scaling factor BACKFILE - NONE Associated background file CORRSCAL - 1.0000 Correlation scaling factor CORRFILE - none Associated correlation file RESPFILE - NONE Associated redistribution matrix file ANCRFILE - none Associated ancillary response file XFLT0001 - none XSPEC selection filter POISSERR - TRUE Whether Poissonian errors apply CHANTYPE - PI Whether channels have been corrected TLMIN1 - 0 First legal Detector channel DETCHANS - 1024 No. of legal detector channels NCHAN - 1024 No. of detector channels in dataset PHAVERSN - 1.1.0 OGIP FITS version number STAT_ERR - FALSE Statistical Error SYS_ERR - TRUE Fractional Systematic Error QUALITY - TRUE Quality Flag GROUPING - FALSE Grouping Flag -------------------------------------------------------------------- -------------------------------------------------------------------- ... ... -------- ... GROUPING ... -------- ... --------------------------------------------- ... Channel Grouping (Channel-Channel) : ... 0 - 25 of undefined grouping (Channel quality=bad) ... 26 - 52 are grouped by a factor 27 ... 53 - 64 are grouped by a factor 12 ... 65 - 72 are grouped by a factor 8 ... 73 - 85 are grouped by a factor 13 ... 86 - 94 are grouped by a factor 9 ... 95 - 102 are grouped by a factor 8 ... 103 - 112 are grouped by a factor 10 ... 113 - 133 are grouped by a factor 21 ... 134 - 157 are grouped by a factor 24 ... 158 - 194 are grouped by a factor 37 ... 195 - 235 are grouped by a factor 41 ... 236 - 303 are grouped by a factor 68 ... 304 - 381 are grouped by a factor 78 ... --------------------------------------------- ... ...... exiting, changes written to file : ad50006000s010412_1.pi ** grppha 2.6.0 completed successfully-> Source occupies chip(s) 0 2 3
** XSELECT V1.3 **
!> Enter session name >[xsel] xsel
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS S0CCDPOW
1 W50 EAST BRIGHT2 HIGH 28/04/93 14:34:00 0.19E+04 642 1011
EXTRACTOR vers 2.0 11 Apr 1997.
Getting FITS WCS Keywords
Doing file: /data/data17/seq_proc/50006000.007/events.tmp
Total Good Bad: Region Time Phase Cut
642 477 165 0 0 0
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
642 477 165 0 0 0
in 1939.59 seconds
Spectrum has 477 counts for 0.2459 counts/sec
-------------------------
MANDATORY KEYWORDS/VALUES
-------------------------
--------------------------------------------------------------------
--------------------------------------------------------------------
EXTNAME - SPECTRUM Name of this BINTABLE
TELESCOP - ASCA Mission/Satellite name
INSTRUME - SIS0 Instrument/Detector
FILTER - Instrument filter in use
EXPOSURE - 1939.6 Integration time (in secs) of PHA data
AREASCAL - 1.0000 Area scaling factor
BACKSCAL - 0.12253 Background scaling factor
BACKFILE - NONE Associated background file
CORRSCAL - 1.0000 Correlation scaling factor
CORRFILE - none Associated correlation file
RESPFILE - NONE Associated redistribution matrix file
ANCRFILE - none Associated ancillary response file
XFLT0001 - none XSPEC selection filter
POISSERR - TRUE Whether Poissonian errors apply
CHANTYPE - PI Whether channels have been corrected
TLMIN1 - 0 First legal Detector channel
DETCHANS - 1024 No. of legal detector channels
NCHAN - 1024 No. of detector channels in dataset
PHAVERSN - 1.1.0 OGIP FITS version number
STAT_ERR - FALSE Statistical Error
SYS_ERR - TRUE Fractional Systematic Error
QUALITY - TRUE Quality Flag
GROUPING - FALSE Grouping Flag
--------------------------------------------------------------------
--------------------------------------------------------------------
... QUALITY
...
... -------
... QUALITY
... -------
... Bad Channels (Channel - Channel)
... ---------------------------------------------
... 0 - 25 have quality 5
... ---------------------------------------------
...
...... exiting, changes written to file : spec0.tmp
Command not found; type ? for a command listing
!xsel:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!xsel:ASCA > set datadir .
Setting data directory to /data/data17/seq_proc/50006000.007/
Setting mkf directory to /data/data17/seq_proc/50006000.007/
!xsel:ASCA > read events events.tmp
Got new instrument: SIS0
Setting: IMAGE binning = 4
WMAP binning = 8
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 4095
Got the minimum time resolution of the read data: 16.000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data17/seq_proc/50006000.007/
HK Directory is: /data/data17/seq_proc/50006000.007/
!xsel:ASCA-SIS0-BRIGHT2 > set phaname PI
!xsel:ASCA-SIS0-BRIGHT2 > filter region ad50006000s032002_1.reg
!xsel:ASCA-SIS0-BRIGHT2 > filter region SIS0_NOTCHIP1.1
!xsel:ASCA-SIS0-BRIGHT2 > filter region SIS0_OFFCHIP.1
!xsel:ASCA-SIS0-BRIGHT2 > filter region ad50006000s010412.discrim
!xsel:ASCA-SIS0-BRIGHT2 > filter region SIS0_NOTCHIP2.1
!xsel:ASCA-SIS0-BRIGHT2 > filter region SIS0_NOTCHIP3.1
!xsel:ASCA-SIS0-BRIGHT2 > extract spectrum
!xsel:ASCA-SIS0-BRIGHT2 > save spectrum spec0.tmp group=yes
Wrote spectrum to spec0.tmp
!xsel:ASCA-SIS0-BRIGHT2 > exit save_session=no
-> sis0c0p40_290296.fits already present in current directorySisrmg Version 1.1, Configured 04/97 This version resolves *all* known keyword incompatibilities with other FTOOLS tasks. If you have previously fudged *any* keywords in the PHA file to compensate, incorrect results will follow. Setting 1st PHA channel to 0 Making v1.1 1180x1024 S0C0 Bright2 PI RMF Calibration data from ./ Please stand by... ...Done.-> SIS0_NOTCHIP0.1 already present in current directory
** XSELECT V1.3 **
!> Enter session name >[xsel] xsel
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS S0CCDPOW
1 W50 EAST BRIGHT2 HIGH 28/04/93 14:34:00 0.19E+04 642 1011
EXTRACTOR vers 2.0 11 Apr 1997.
Getting FITS WCS Keywords
Doing file: /data/data17/seq_proc/50006000.007/events.tmp
Total Good Bad: Region Time Phase Cut
642 46 596 0 0 0
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
642 46 596 0 0 0
in 1939.59 seconds
Spectrum has 46 counts for 2.3716E-02 counts/sec
-------------------------
MANDATORY KEYWORDS/VALUES
-------------------------
--------------------------------------------------------------------
--------------------------------------------------------------------
EXTNAME - SPECTRUM Name of this BINTABLE
TELESCOP - ASCA Mission/Satellite name
INSTRUME - SIS0 Instrument/Detector
FILTER - Instrument filter in use
EXPOSURE - 1939.6 Integration time (in secs) of PHA data
AREASCAL - 1.0000 Area scaling factor
BACKSCAL - 2.93359E-02 Background scaling factor
BACKFILE - NONE Associated background file
CORRSCAL - 1.0000 Correlation scaling factor
CORRFILE - none Associated correlation file
RESPFILE - NONE Associated redistribution matrix file
ANCRFILE - none Associated ancillary response file
XFLT0001 - none XSPEC selection filter
POISSERR - TRUE Whether Poissonian errors apply
CHANTYPE - PI Whether channels have been corrected
TLMIN1 - 0 First legal Detector channel
DETCHANS - 1024 No. of legal detector channels
NCHAN - 1024 No. of detector channels in dataset
PHAVERSN - 1.1.0 OGIP FITS version number
STAT_ERR - FALSE Statistical Error
SYS_ERR - TRUE Fractional Systematic Error
QUALITY - TRUE Quality Flag
GROUPING - FALSE Grouping Flag
--------------------------------------------------------------------
--------------------------------------------------------------------
... QUALITY
...
... -------
... QUALITY
... -------
... Bad Channels (Channel - Channel)
... ---------------------------------------------
... 0 - 25 have quality 5
... ---------------------------------------------
...
...... exiting, changes written to file : spec2.tmp
Command not found; type ? for a command listing
!xsel:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!xsel:ASCA > set datadir .
Setting data directory to /data/data17/seq_proc/50006000.007/
Setting mkf directory to /data/data17/seq_proc/50006000.007/
!xsel:ASCA > read events events.tmp
Got new instrument: SIS0
Setting: IMAGE binning = 4
WMAP binning = 8
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 4095
Got the minimum time resolution of the read data: 16.000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data17/seq_proc/50006000.007/
HK Directory is: /data/data17/seq_proc/50006000.007/
!xsel:ASCA-SIS0-BRIGHT2 > set phaname PI
!xsel:ASCA-SIS0-BRIGHT2 > filter region ad50006000s032002_1.reg
!xsel:ASCA-SIS0-BRIGHT2 > filter region SIS0_NOTCHIP1.1
!xsel:ASCA-SIS0-BRIGHT2 > filter region SIS0_OFFCHIP.1
!xsel:ASCA-SIS0-BRIGHT2 > filter region ad50006000s010412.discrim
!xsel:ASCA-SIS0-BRIGHT2 > filter region SIS0_NOTCHIP0.1
!xsel:ASCA-SIS0-BRIGHT2 > filter region SIS0_NOTCHIP3.1
!xsel:ASCA-SIS0-BRIGHT2 > extract spectrum
!xsel:ASCA-SIS0-BRIGHT2 > save spectrum spec2.tmp group=yes
Wrote spectrum to spec2.tmp
!xsel:ASCA-SIS0-BRIGHT2 > exit save_session=no
-> sis0c2p40_290296.fits already present in current directorySisrmg Version 1.1, Configured 04/97 This version resolves *all* known keyword incompatibilities with other FTOOLS tasks. If you have previously fudged *any* keywords in the PHA file to compensate, incorrect results will follow. Setting 1st PHA channel to 0 Making v1.1 1180x1024 S0C2 Bright2 PI RMF Calibration data from ./ Please stand by... ...Done.-> SIS0_NOTCHIP0.1 already present in current directory
** XSELECT V1.3 **
!> Enter session name >[xsel] xsel
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS S0CCDPOW
1 W50 EAST BRIGHT2 HIGH 28/04/93 14:34:00 0.19E+04 642 1011
EXTRACTOR vers 2.0 11 Apr 1997.
Getting FITS WCS Keywords
Doing file: /data/data17/seq_proc/50006000.007/events.tmp
Total Good Bad: Region Time Phase Cut
642 119 523 0 0 0
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
642 119 523 0 0 0
in 1939.59 seconds
Spectrum has 119 counts for 6.1353E-02 counts/sec
-------------------------
MANDATORY KEYWORDS/VALUES
-------------------------
--------------------------------------------------------------------
--------------------------------------------------------------------
EXTNAME - SPECTRUM Name of this BINTABLE
TELESCOP - ASCA Mission/Satellite name
INSTRUME - SIS0 Instrument/Detector
FILTER - Instrument filter in use
EXPOSURE - 1939.6 Integration time (in secs) of PHA data
AREASCAL - 1.0000 Area scaling factor
BACKSCAL - 6.98730E-02 Background scaling factor
BACKFILE - NONE Associated background file
CORRSCAL - 1.0000 Correlation scaling factor
CORRFILE - none Associated correlation file
RESPFILE - NONE Associated redistribution matrix file
ANCRFILE - none Associated ancillary response file
XFLT0001 - none XSPEC selection filter
POISSERR - TRUE Whether Poissonian errors apply
CHANTYPE - PI Whether channels have been corrected
TLMIN1 - 0 First legal Detector channel
DETCHANS - 1024 No. of legal detector channels
NCHAN - 1024 No. of detector channels in dataset
PHAVERSN - 1.1.0 OGIP FITS version number
STAT_ERR - FALSE Statistical Error
SYS_ERR - TRUE Fractional Systematic Error
QUALITY - TRUE Quality Flag
GROUPING - FALSE Grouping Flag
--------------------------------------------------------------------
--------------------------------------------------------------------
... QUALITY
...
... -------
... QUALITY
... -------
... Bad Channels (Channel - Channel)
... ---------------------------------------------
... 0 - 25 have quality 5
... ---------------------------------------------
...
...... exiting, changes written to file : spec3.tmp
Command not found; type ? for a command listing
!xsel:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!xsel:ASCA > set datadir .
Setting data directory to /data/data17/seq_proc/50006000.007/
Setting mkf directory to /data/data17/seq_proc/50006000.007/
!xsel:ASCA > read events events.tmp
Got new instrument: SIS0
Setting: IMAGE binning = 4
WMAP binning = 8
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 4095
Got the minimum time resolution of the read data: 16.000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data17/seq_proc/50006000.007/
HK Directory is: /data/data17/seq_proc/50006000.007/
!xsel:ASCA-SIS0-BRIGHT2 > set phaname PI
!xsel:ASCA-SIS0-BRIGHT2 > filter region ad50006000s032002_1.reg
!xsel:ASCA-SIS0-BRIGHT2 > filter region SIS0_NOTCHIP1.1
!xsel:ASCA-SIS0-BRIGHT2 > filter region SIS0_OFFCHIP.1
!xsel:ASCA-SIS0-BRIGHT2 > filter region ad50006000s010412.discrim
!xsel:ASCA-SIS0-BRIGHT2 > filter region SIS0_NOTCHIP0.1
!xsel:ASCA-SIS0-BRIGHT2 > filter region SIS0_NOTCHIP2.1
!xsel:ASCA-SIS0-BRIGHT2 > extract spectrum
!xsel:ASCA-SIS0-BRIGHT2 > save spectrum spec3.tmp group=yes
Wrote spectrum to spec3.tmp
!xsel:ASCA-SIS0-BRIGHT2 > exit save_session=no
-> sis0c3p40_290296.fits already present in current directorySisrmg Version 1.1, Configured 04/97 This version resolves *all* known keyword incompatibilities with other FTOOLS tasks. If you have previously fudged *any* keywords in the PHA file to compensate, incorrect results will follow. Setting 1st PHA channel to 0 Making v1.1 1180x1024 S0C3 Bright2 PI RMF Calibration data from ./ Please stand by... ...Done.-> Chip weights:
rmf0.tmp 0.742990654205608 rmf2.tmp 0.0716510903426791 rmf3.tmp 0.185358255451713-> Standard Output From FTOOL addrmf:
ADDRMF vers 1.10 10 April, 1997.
Summing ...
7.430E-01 * rmf0.tmp
7.165E-02 * rmf2.tmp
1.854E-01 * rmf3.tmp
RMF # 1 : rmf0.tmp 0.74
ASCA SIS0 NONE NONE PI
RMF # 2 : rmf2.tmp 0.07
ASCA SIS0 NONE NONE PI
RMF # 3 : rmf3.tmp 0.19
ASCA SIS0 NONE NONE PI
-> Generating ad50006000s010412_1.arf with point=no
ASCAARF vers 2.72 14 Mar 1997.
Input WMAP array has size 81 by 95 bins
expanded to 81 by 95 bins
First WMAP bin is at detector pixel 224 456
8 detector pixels per WMAP bin
WMAP bin size is 0.21600 mm
0.21216 arcmin
Selected region size is 214.21 arcmin^2
Optical axis is detector pixel 662.72 559.02
1180 energies from RMF file
Effective area fudge applied
Arf filter applied
Total counts in region = 6.34000E+02
Weighted mean angle from optical axis = 9.080 arcmin
-> Standard Output From STOOL group_event_files:1 ad50006000s100102h.evt 25195 1 ad50006000s100202m.evt 25195 1 ad50006000s100502m.evt 25195 1 ad50006000s100602h.evt 25195-> Fetching SIS1_OFFCHIP.1
ad50006000s100102h.evt ad50006000s100202m.evt ad50006000s100502m.evt ad50006000s100602h.evt-> Standard Output From FTOOL xselect:
** XSELECT V1.3 **
!> Enter session name >[xsel] xsel
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS S1CCDPOW
1 W50 EAST BRIGHT HIGH 28/04/93 03:44:28 0.18E+05 12214 1111
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS S1CCDPOW
1 W50 EAST BRIGHT HIGH 28/04/93 03:44:28 0.18E+05 12214 1111
2 W50 EAST BRIGHT MEDIUM 27/04/93 23:50:32 0.11E+05 7884 1111
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS S1CCDPOW
1 W50 EAST BRIGHT HIGH 28/04/93 03:44:28 0.18E+05 12214 1111
2 W50 EAST BRIGHT MEDIUM 27/04/93 23:50:32 0.11E+05 7884 1111
3 W50 EAST BRIGHT MEDIUM 28/04/93 19:50:16 0.56E+04 4002 1111
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS S1CCDPOW
1 W50 EAST BRIGHT HIGH 28/04/93 03:44:28 0.18E+05 12214 1111
2 W50 EAST BRIGHT MEDIUM 27/04/93 23:50:32 0.11E+05 7884 1111
3 W50 EAST BRIGHT MEDIUM 28/04/93 19:50:16 0.56E+04 4002 1111
4 W50 EAST BRIGHT HIGH 28/04/93 22:52:12 0.14E+04 1095 1111
EXTRACTOR vers 2.0 11 Apr 1997.
Getting FITS WCS Keywords
Doing file: /data/data17/seq_proc/50006000.007/ad50006000s100102h.evt
Total Good Bad: Region Time Phase Cut
12214 7657 4557 0 0 0
Doing file: /data/data17/seq_proc/50006000.007/ad50006000s100202m.evt
Total Good Bad: Region Time Phase Cut
7884 4988 2896 0 0 0
Doing file: /data/data17/seq_proc/50006000.007/ad50006000s100502m.evt
Total Good Bad: Region Time Phase Cut
4002 2490 1512 0 0 0
Doing file: /data/data17/seq_proc/50006000.007/ad50006000s100602h.evt
Total Good Bad: Region Time Phase Cut
1095 725 370 0 0 0
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
25195 15860 9335 0 0 0
in 35648.30 seconds
Spectrum has 15860 counts for 0.4449 counts/sec
-------------------------
MANDATORY KEYWORDS/VALUES
-------------------------
--------------------------------------------------------------------
--------------------------------------------------------------------
EXTNAME - SPECTRUM Name of this BINTABLE
TELESCOP - ASCA Mission/Satellite name
INSTRUME - SIS1 Instrument/Detector
FILTER - Instrument filter in use
EXPOSURE - 35648. Integration time (in secs) of PHA data
AREASCAL - 1.0000 Area scaling factor
BACKSCAL - 0.22908 Background scaling factor
BACKFILE - NONE Associated background file
CORRSCAL - 1.0000 Correlation scaling factor
CORRFILE - none Associated correlation file
RESPFILE - NONE Associated redistribution matrix file
ANCRFILE - none Associated ancillary response file
XFLT0001 - none XSPEC selection filter
POISSERR - TRUE Whether Poissonian errors apply
CHANTYPE - PI Whether channels have been corrected
TLMIN1 - 0 First legal Detector channel
DETCHANS - 512 No. of legal detector channels
NCHAN - 512 No. of detector channels in dataset
PHAVERSN - 1.1.0 OGIP FITS version number
STAT_ERR - FALSE Statistical Error
SYS_ERR - TRUE Fractional Systematic Error
QUALITY - TRUE Quality Flag
GROUPING - FALSE Grouping Flag
--------------------------------------------------------------------
--------------------------------------------------------------------
... QUALITY
...
... -------
... QUALITY
... -------
... Bad Channels (Channel - Channel)
... ---------------------------------------------
... 0 - 12 have quality 5
... ---------------------------------------------
...
...... exiting, changes written to file : ad50006000s110102_1.pi
EXTRACTOR vers 2.0 11 Apr 1997.
Doing file: /data/data17/seq_proc/50006000.007/ad50006000s100102h.evt
Total Good Bad: Region Time Phase Cut
12214 7657 4557 0 0 0
Writing events file
7657 events written to the output file
Doing file: /data/data17/seq_proc/50006000.007/ad50006000s100202m.evt
Total Good Bad: Region Time Phase Cut
7884 4988 2896 0 0 0
Writing events file
12645 events written to the output file
Doing file: /data/data17/seq_proc/50006000.007/ad50006000s100502m.evt
Total Good Bad: Region Time Phase Cut
4002 2490 1512 0 0 0
Writing events file
15135 events written to the output file
Doing file: /data/data17/seq_proc/50006000.007/ad50006000s100602h.evt
Total Good Bad: Region Time Phase Cut
1095 725 370 0 0 0
Writing events file
15860 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
25195 15860 9335 0 0 0
in 35648.30 seconds
Command not found; type ? for a command listing
!xsel:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!xsel:ASCA > set datadir .
Setting data directory to /data/data17/seq_proc/50006000.007/
Setting mkf directory to /data/data17/seq_proc/50006000.007/
!xsel:ASCA > read events ad50006000s100102h.evt
Got new instrument: SIS1
Setting: IMAGE binning = 4
WMAP binning = 8
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 2047
Got the minimum time resolution of the read data: 16.000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data17/seq_proc/50006000.007/
HK Directory is: /data/data17/seq_proc/50006000.007/
!xsel:ASCA-SIS1-BRIGHT > read events ad50006000s100202m.evt
Getting Min and Max for Energy Column...
Got min and max for PI: 0 2047
Got the minimum time resolution of the read data: 16.000
Number of files read in: 2
******************** Observation Catalogue ********************
Data Directory is: /data/data17/seq_proc/50006000.007/
HK Directory is: /data/data17/seq_proc/50006000.007/
!xsel:ASCA-SIS1-BRIGHT > read events ad50006000s100502m.evt
Getting Min and Max for Energy Column...
Got min and max for PI: 0 2047
Got the minimum time resolution of the read data: 16.000
Number of files read in: 3
******************** Observation Catalogue ********************
Data Directory is: /data/data17/seq_proc/50006000.007/
HK Directory is: /data/data17/seq_proc/50006000.007/
!xsel:ASCA-SIS1-BRIGHT > read events ad50006000s100602h.evt
Getting Min and Max for Energy Column...
Got min and max for PI: 0 2047
Got the minimum time resolution of the read data: 16.000
Number of files read in: 4
******************** Observation Catalogue ********************
Data Directory is: /data/data17/seq_proc/50006000.007/
HK Directory is: /data/data17/seq_proc/50006000.007/
!xsel:ASCA-SIS1-BRIGHT > set phaname PI
!xsel:ASCA-SIS1-BRIGHT > filter region ad50006000s132002_1.reg
!xsel:ASCA-SIS1-BRIGHT > filter region SIS1_OFFCHIP.1
!xsel:ASCA-SIS1-BRIGHT > filter region ad50006000s110102.discrim
!xsel:ASCA-SIS1-BRIGHT > extract spectrum
!xsel:ASCA-SIS1-BRIGHT > save spectrum ad50006000s110102_1.pi group=yes
Wrote spectrum to ad50006000s110102_1.pi
!xsel:ASCA-SIS1-BRIGHT > extract events
!xsel:ASCA-SIS1-BRIGHT > save events outfile=events.tmp use_events=yes
Wrote events list to file events.tmp
Changing Data directory from:
/data/data17/seq_proc/50006000.007/
to the current working directory.
!xsel:ASCA-SIS1-BRIGHT > exit save_session=no
-> Grouping ad50006000s110102_1.pi to 40 counts/bin------------------------- MANDATORY KEYWORDS/VALUES ------------------------- -------------------------------------------------------------------- -------------------------------------------------------------------- EXTNAME - SPECTRUM Name of this BINTABLE TELESCOP - ASCA Mission/Satellite name INSTRUME - SIS1 Instrument/Detector FILTER - Instrument filter in use EXPOSURE - 35648. Integration time (in secs) of PHA data AREASCAL - 1.0000 Area scaling factor BACKSCAL - 0.22908 Background scaling factor BACKFILE - NONE Associated background file CORRSCAL - 1.0000 Correlation scaling factor CORRFILE - none Associated correlation file RESPFILE - NONE Associated redistribution matrix file ANCRFILE - none Associated ancillary response file XFLT0001 - none XSPEC selection filter POISSERR - TRUE Whether Poissonian errors apply CHANTYPE - PI Whether channels have been corrected TLMIN1 - 0 First legal Detector channel DETCHANS - 512 No. of legal detector channels NCHAN - 512 No. of detector channels in dataset PHAVERSN - 1.1.0 OGIP FITS version number STAT_ERR - FALSE Statistical Error SYS_ERR - TRUE Fractional Systematic Error QUALITY - TRUE Quality Flag GROUPING - FALSE Grouping Flag -------------------------------------------------------------------- -------------------------------------------------------------------- ... ... -------- ... GROUPING ... -------- ... --------------------------------------------- ... Channel Grouping (Channel-Channel) : ... 0 - 12 of undefined grouping (Channel quality=bad) ... 13 - 13 are single channels ... 14 - 15 are grouped by a factor 2 ... 16 - 99 are single channels ... 100 - 101 are grouped by a factor 2 ... 102 - 103 are single channels ... 104 - 105 are grouped by a factor 2 ... 106 - 109 are single channels ... 110 - 115 are grouped by a factor 2 ... 116 - 118 are single channels ... 119 - 120 are grouped by a factor 2 ... 121 - 121 are single channels ... 122 - 123 are grouped by a factor 2 ... 124 - 124 are single channels ... 125 - 126 are grouped by a factor 2 ... 127 - 127 are single channels ... 128 - 153 are grouped by a factor 2 ... 154 - 159 are grouped by a factor 3 ... 160 - 167 are grouped by a factor 2 ... 168 - 185 are grouped by a factor 3 ... 186 - 190 are grouped by a factor 5 ... 191 - 194 are grouped by a factor 4 ... 195 - 199 are grouped by a factor 5 ... 200 - 205 are grouped by a factor 6 ... 206 - 208 are grouped by a factor 3 ... 209 - 214 are grouped by a factor 6 ... 215 - 217 are grouped by a factor 3 ... 218 - 221 are grouped by a factor 4 ... 222 - 228 are grouped by a factor 7 ... 229 - 232 are grouped by a factor 4 ... 233 - 244 are grouped by a factor 6 ... 245 - 252 are grouped by a factor 8 ... 253 - 258 are grouped by a factor 6 ... 259 - 266 are grouped by a factor 8 ... 267 - 278 are grouped by a factor 12 ... 279 - 291 are grouped by a factor 13 ... 292 - 305 are grouped by a factor 14 ... 306 - 326 are grouped by a factor 21 ... 327 - 338 are grouped by a factor 12 ... 339 - 362 are grouped by a factor 24 ... 363 - 389 are grouped by a factor 27 ... 390 - 412 are grouped by a factor 23 ... 413 - 429 are grouped by a factor 17 ... 430 - 436 are grouped by a factor 7 ... 437 - 440 are grouped by a factor 4 ... 441 - 446 are grouped by a factor 3 ... 447 - 450 are grouped by a factor 4 ... 451 - 459 are grouped by a factor 9 ... 460 - 475 are grouped by a factor 16 ... 476 - 477 are grouped by a factor 2 ... 478 - 480 are grouped by a factor 3 ... 481 - 484 are grouped by a factor 4 ... --------------------------------------------- ... ...... exiting, changes written to file : ad50006000s110102_1.pi ** grppha 2.6.0 completed successfully-> Source occupies chip(s) 0 1 2 3
** XSELECT V1.3 **
!> Enter session name >[xsel] xsel
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS S1CCDPOW
1 W50 EAST BRIGHT HIGH 27/04/93 23:50:32 0.36E+05 15860 1111
EXTRACTOR vers 2.0 11 Apr 1997.
Getting FITS WCS Keywords
Doing file: /data/data17/seq_proc/50006000.007/events.tmp
Total Good Bad: Region Time Phase Cut
15860 387 15473 0 0 0
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
15860 387 15473 0 0 0
in 35648.30 seconds
Spectrum has 387 counts for 1.0856E-02 counts/sec
-------------------------
MANDATORY KEYWORDS/VALUES
-------------------------
--------------------------------------------------------------------
--------------------------------------------------------------------
EXTNAME - SPECTRUM Name of this BINTABLE
TELESCOP - ASCA Mission/Satellite name
INSTRUME - SIS1 Instrument/Detector
FILTER - Instrument filter in use
EXPOSURE - 35648. Integration time (in secs) of PHA data
AREASCAL - 1.0000 Area scaling factor
BACKSCAL - 3.61719E-02 Background scaling factor
BACKFILE - NONE Associated background file
CORRSCAL - 1.0000 Correlation scaling factor
CORRFILE - none Associated correlation file
RESPFILE - NONE Associated redistribution matrix file
ANCRFILE - none Associated ancillary response file
XFLT0001 - none XSPEC selection filter
POISSERR - TRUE Whether Poissonian errors apply
CHANTYPE - PI Whether channels have been corrected
TLMIN1 - 0 First legal Detector channel
DETCHANS - 512 No. of legal detector channels
NCHAN - 512 No. of detector channels in dataset
PHAVERSN - 1.1.0 OGIP FITS version number
STAT_ERR - FALSE Statistical Error
SYS_ERR - TRUE Fractional Systematic Error
QUALITY - TRUE Quality Flag
GROUPING - FALSE Grouping Flag
--------------------------------------------------------------------
--------------------------------------------------------------------
... QUALITY
...
... -------
... QUALITY
... -------
... Bad Channels (Channel - Channel)
... ---------------------------------------------
... 0 - 12 have quality 5
... ---------------------------------------------
...
...... exiting, changes written to file : spec0.tmp
Command not found; type ? for a command listing
!xsel:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!xsel:ASCA > set datadir .
Setting data directory to /data/data17/seq_proc/50006000.007/
Setting mkf directory to /data/data17/seq_proc/50006000.007/
!xsel:ASCA > read events events.tmp
Got new instrument: SIS1
Setting: IMAGE binning = 4
WMAP binning = 8
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 2047
Got the minimum time resolution of the read data: 16.000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data17/seq_proc/50006000.007/
HK Directory is: /data/data17/seq_proc/50006000.007/
!xsel:ASCA-SIS1-BRIGHT > set phaname PI
!xsel:ASCA-SIS1-BRIGHT > filter region ad50006000s132002_1.reg
!xsel:ASCA-SIS1-BRIGHT > filter region SIS1_OFFCHIP.1
!xsel:ASCA-SIS1-BRIGHT > filter region ad50006000s110102.discrim
!xsel:ASCA-SIS1-BRIGHT > filter region SIS1_NOTCHIP1.1
!xsel:ASCA-SIS1-BRIGHT > filter region SIS1_NOTCHIP2.1
!xsel:ASCA-SIS1-BRIGHT > filter region SIS1_NOTCHIP3.1
!xsel:ASCA-SIS1-BRIGHT > extract spectrum
!xsel:ASCA-SIS1-BRIGHT > save spectrum spec0.tmp group=yes
Wrote spectrum to spec0.tmp
!xsel:ASCA-SIS1-BRIGHT > exit save_session=no
-> Fetching sis1c0p40_290296.fitsSisrmg Version 1.1, Configured 04/97 This version resolves *all* known keyword incompatibilities with other FTOOLS tasks. If you have previously fudged *any* keywords in the PHA file to compensate, incorrect results will follow. Setting 1st PHA channel to 0 Making v1.1 1180x512 S1C0 Bright PI RMF Calibration data from ./ Please stand by... ...Done.-> Fetching SIS1_NOTCHIP0.1
** XSELECT V1.3 **
!> Enter session name >[xsel] xsel
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS S1CCDPOW
1 W50 EAST BRIGHT HIGH 27/04/93 23:50:32 0.36E+05 15860 1111
EXTRACTOR vers 2.0 11 Apr 1997.
Getting FITS WCS Keywords
Doing file: /data/data17/seq_proc/50006000.007/events.tmp
Total Good Bad: Region Time Phase Cut
15860 2314 13546 0 0 0
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
15860 2314 13546 0 0 0
in 35648.30 seconds
Spectrum has 2314 counts for 6.4912E-02 counts/sec
-------------------------
MANDATORY KEYWORDS/VALUES
-------------------------
--------------------------------------------------------------------
--------------------------------------------------------------------
EXTNAME - SPECTRUM Name of this BINTABLE
TELESCOP - ASCA Mission/Satellite name
INSTRUME - SIS1 Instrument/Detector
FILTER - Instrument filter in use
EXPOSURE - 35648. Integration time (in secs) of PHA data
AREASCAL - 1.0000 Area scaling factor
BACKSCAL - 8.13672E-02 Background scaling factor
BACKFILE - NONE Associated background file
CORRSCAL - 1.0000 Correlation scaling factor
CORRFILE - none Associated correlation file
RESPFILE - NONE Associated redistribution matrix file
ANCRFILE - none Associated ancillary response file
XFLT0001 - none XSPEC selection filter
POISSERR - TRUE Whether Poissonian errors apply
CHANTYPE - PI Whether channels have been corrected
TLMIN1 - 0 First legal Detector channel
DETCHANS - 512 No. of legal detector channels
NCHAN - 512 No. of detector channels in dataset
PHAVERSN - 1.1.0 OGIP FITS version number
STAT_ERR - FALSE Statistical Error
SYS_ERR - TRUE Fractional Systematic Error
QUALITY - TRUE Quality Flag
GROUPING - FALSE Grouping Flag
--------------------------------------------------------------------
--------------------------------------------------------------------
... QUALITY
...
... -------
... QUALITY
... -------
... Bad Channels (Channel - Channel)
... ---------------------------------------------
... 0 - 12 have quality 5
... ---------------------------------------------
...
...... exiting, changes written to file : spec1.tmp
Command not found; type ? for a command listing
!xsel:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!xsel:ASCA > set datadir .
Setting data directory to /data/data17/seq_proc/50006000.007/
Setting mkf directory to /data/data17/seq_proc/50006000.007/
!xsel:ASCA > read events events.tmp
Got new instrument: SIS1
Setting: IMAGE binning = 4
WMAP binning = 8
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 2047
Got the minimum time resolution of the read data: 16.000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data17/seq_proc/50006000.007/
HK Directory is: /data/data17/seq_proc/50006000.007/
!xsel:ASCA-SIS1-BRIGHT > set phaname PI
!xsel:ASCA-SIS1-BRIGHT > filter region ad50006000s132002_1.reg
!xsel:ASCA-SIS1-BRIGHT > filter region SIS1_OFFCHIP.1
!xsel:ASCA-SIS1-BRIGHT > filter region ad50006000s110102.discrim
!xsel:ASCA-SIS1-BRIGHT > filter region SIS1_NOTCHIP0.1
!xsel:ASCA-SIS1-BRIGHT > filter region SIS1_NOTCHIP2.1
!xsel:ASCA-SIS1-BRIGHT > filter region SIS1_NOTCHIP3.1
!xsel:ASCA-SIS1-BRIGHT > extract spectrum
!xsel:ASCA-SIS1-BRIGHT > save spectrum spec1.tmp group=yes
Wrote spectrum to spec1.tmp
!xsel:ASCA-SIS1-BRIGHT > exit save_session=no
-> Fetching sis1c1p40_290296.fitsSisrmg Version 1.1, Configured 04/97 This version resolves *all* known keyword incompatibilities with other FTOOLS tasks. If you have previously fudged *any* keywords in the PHA file to compensate, incorrect results will follow. Setting 1st PHA channel to 0 Making v1.1 1180x512 S1C1 Bright PI RMF Calibration data from ./ Please stand by... ...Done.-> SIS1_NOTCHIP0.1 already present in current directory
** XSELECT V1.3 **
!> Enter session name >[xsel] xsel
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS S1CCDPOW
1 W50 EAST BRIGHT HIGH 27/04/93 23:50:32 0.36E+05 15860 1111
EXTRACTOR vers 2.0 11 Apr 1997.
Getting FITS WCS Keywords
Doing file: /data/data17/seq_proc/50006000.007/events.tmp
Total Good Bad: Region Time Phase Cut
15860 10516 5344 0 0 0
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
15860 10516 5344 0 0 0
in 35648.30 seconds
Spectrum has 10516 counts for 0.2950 counts/sec
-------------------------
MANDATORY KEYWORDS/VALUES
-------------------------
--------------------------------------------------------------------
--------------------------------------------------------------------
EXTNAME - SPECTRUM Name of this BINTABLE
TELESCOP - ASCA Mission/Satellite name
INSTRUME - SIS1 Instrument/Detector
FILTER - Instrument filter in use
EXPOSURE - 35648. Integration time (in secs) of PHA data
AREASCAL - 1.0000 Area scaling factor
BACKSCAL - 0.13381 Background scaling factor
BACKFILE - NONE Associated background file
CORRSCAL - 1.0000 Correlation scaling factor
CORRFILE - none Associated correlation file
RESPFILE - NONE Associated redistribution matrix file
ANCRFILE - none Associated ancillary response file
XFLT0001 - none XSPEC selection filter
POISSERR - TRUE Whether Poissonian errors apply
CHANTYPE - PI Whether channels have been corrected
TLMIN1 - 0 First legal Detector channel
DETCHANS - 512 No. of legal detector channels
NCHAN - 512 No. of detector channels in dataset
PHAVERSN - 1.1.0 OGIP FITS version number
STAT_ERR - FALSE Statistical Error
SYS_ERR - TRUE Fractional Systematic Error
QUALITY - TRUE Quality Flag
GROUPING - FALSE Grouping Flag
--------------------------------------------------------------------
--------------------------------------------------------------------
... QUALITY
...
... -------
... QUALITY
... -------
... Bad Channels (Channel - Channel)
... ---------------------------------------------
... 0 - 12 have quality 5
... ---------------------------------------------
...
...... exiting, changes written to file : spec2.tmp
Command not found; type ? for a command listing
!xsel:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!xsel:ASCA > set datadir .
Setting data directory to /data/data17/seq_proc/50006000.007/
Setting mkf directory to /data/data17/seq_proc/50006000.007/
!xsel:ASCA > read events events.tmp
Got new instrument: SIS1
Setting: IMAGE binning = 4
WMAP binning = 8
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 2047
Got the minimum time resolution of the read data: 16.000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data17/seq_proc/50006000.007/
HK Directory is: /data/data17/seq_proc/50006000.007/
!xsel:ASCA-SIS1-BRIGHT > set phaname PI
!xsel:ASCA-SIS1-BRIGHT > filter region ad50006000s132002_1.reg
!xsel:ASCA-SIS1-BRIGHT > filter region SIS1_OFFCHIP.1
!xsel:ASCA-SIS1-BRIGHT > filter region ad50006000s110102.discrim
!xsel:ASCA-SIS1-BRIGHT > filter region SIS1_NOTCHIP0.1
!xsel:ASCA-SIS1-BRIGHT > filter region SIS1_NOTCHIP1.1
!xsel:ASCA-SIS1-BRIGHT > filter region SIS1_NOTCHIP3.1
!xsel:ASCA-SIS1-BRIGHT > extract spectrum
!xsel:ASCA-SIS1-BRIGHT > save spectrum spec2.tmp group=yes
Wrote spectrum to spec2.tmp
!xsel:ASCA-SIS1-BRIGHT > exit save_session=no
-> Fetching sis1c2p40_290296.fitsSisrmg Version 1.1, Configured 04/97 This version resolves *all* known keyword incompatibilities with other FTOOLS tasks. If you have previously fudged *any* keywords in the PHA file to compensate, incorrect results will follow. Setting 1st PHA channel to 0 Making v1.1 1180x512 S1C2 Bright PI RMF Calibration data from ./ Please stand by... ...Done.-> SIS1_NOTCHIP0.1 already present in current directory
** XSELECT V1.3 **
!> Enter session name >[xsel] xsel
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS S1CCDPOW
1 W50 EAST BRIGHT HIGH 27/04/93 23:50:32 0.36E+05 15860 1111
EXTRACTOR vers 2.0 11 Apr 1997.
Getting FITS WCS Keywords
Doing file: /data/data17/seq_proc/50006000.007/events.tmp
Total Good Bad: Region Time Phase Cut
15860 2643 13217 0 0 0
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
15860 2643 13217 0 0 0
in 35648.30 seconds
Spectrum has 2643 counts for 7.4141E-02 counts/sec
-------------------------
MANDATORY KEYWORDS/VALUES
-------------------------
--------------------------------------------------------------------
--------------------------------------------------------------------
EXTNAME - SPECTRUM Name of this BINTABLE
TELESCOP - ASCA Mission/Satellite name
INSTRUME - SIS1 Instrument/Detector
FILTER - Instrument filter in use
EXPOSURE - 35648. Integration time (in secs) of PHA data
AREASCAL - 1.0000 Area scaling factor
BACKSCAL - 6.53027E-02 Background scaling factor
BACKFILE - NONE Associated background file
CORRSCAL - 1.0000 Correlation scaling factor
CORRFILE - none Associated correlation file
RESPFILE - NONE Associated redistribution matrix file
ANCRFILE - none Associated ancillary response file
XFLT0001 - none XSPEC selection filter
POISSERR - TRUE Whether Poissonian errors apply
CHANTYPE - PI Whether channels have been corrected
TLMIN1 - 0 First legal Detector channel
DETCHANS - 512 No. of legal detector channels
NCHAN - 512 No. of detector channels in dataset
PHAVERSN - 1.1.0 OGIP FITS version number
STAT_ERR - FALSE Statistical Error
SYS_ERR - TRUE Fractional Systematic Error
QUALITY - TRUE Quality Flag
GROUPING - FALSE Grouping Flag
--------------------------------------------------------------------
--------------------------------------------------------------------
... QUALITY
...
... -------
... QUALITY
... -------
... Bad Channels (Channel - Channel)
... ---------------------------------------------
... 0 - 12 have quality 5
... ---------------------------------------------
...
...... exiting, changes written to file : spec3.tmp
Command not found; type ? for a command listing
!xsel:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!xsel:ASCA > set datadir .
Setting data directory to /data/data17/seq_proc/50006000.007/
Setting mkf directory to /data/data17/seq_proc/50006000.007/
!xsel:ASCA > read events events.tmp
Got new instrument: SIS1
Setting: IMAGE binning = 4
WMAP binning = 8
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 2047
Got the minimum time resolution of the read data: 16.000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data17/seq_proc/50006000.007/
HK Directory is: /data/data17/seq_proc/50006000.007/
!xsel:ASCA-SIS1-BRIGHT > set phaname PI
!xsel:ASCA-SIS1-BRIGHT > filter region ad50006000s132002_1.reg
!xsel:ASCA-SIS1-BRIGHT > filter region SIS1_OFFCHIP.1
!xsel:ASCA-SIS1-BRIGHT > filter region ad50006000s110102.discrim
!xsel:ASCA-SIS1-BRIGHT > filter region SIS1_NOTCHIP0.1
!xsel:ASCA-SIS1-BRIGHT > filter region SIS1_NOTCHIP1.1
!xsel:ASCA-SIS1-BRIGHT > filter region SIS1_NOTCHIP2.1
!xsel:ASCA-SIS1-BRIGHT > extract spectrum
!xsel:ASCA-SIS1-BRIGHT > save spectrum spec3.tmp group=yes
Wrote spectrum to spec3.tmp
!xsel:ASCA-SIS1-BRIGHT > exit save_session=no
-> Fetching sis1c3p40_290296.fitsSisrmg Version 1.1, Configured 04/97 This version resolves *all* known keyword incompatibilities with other FTOOLS tasks. If you have previously fudged *any* keywords in the PHA file to compensate, incorrect results will follow. Setting 1st PHA channel to 0 Making v1.1 1180x512 S1C3 Bright PI RMF Calibration data from ./ Please stand by... ...Done.-> Chip weights:
rmf0.tmp 0.0244010088272383 rmf1.tmp 0.145901639344262 rmf2.tmp 0.663051702395965 rmf3.tmp 0.166645649432535-> Standard Output From FTOOL addrmf:
ADDRMF vers 1.10 10 April, 1997.
Summing ...
2.440E-02 * rmf0.tmp
1.459E-01 * rmf1.tmp
6.631E-01 * rmf2.tmp
1.666E-01 * rmf3.tmp
RMF # 1 : rmf0.tmp 0.02
ASCA SIS1 NONE NONE PI
RMF # 2 : rmf1.tmp 0.15
ASCA SIS1 NONE NONE PI
RMF # 3 : rmf2.tmp 0.66
ASCA SIS1 NONE NONE PI
RMF # 4 : rmf3.tmp 0.17
ASCA SIS1 NONE NONE PI
-> Generating ad50006000s110102_1.arf with point=no
ASCAARF vers 2.72 14 Mar 1997.
Input WMAP array has size 82 by 99 bins
expanded to 82 by 99 bins
First WMAP bin is at detector pixel 224 464
8 detector pixels per WMAP bin
WMAP bin size is 0.21600 mm
0.21216 arcmin
Selected region size is 263.97 arcmin^2
Optical axis is detector pixel 618.28 773.83
1180 energies from RMF file
Effective area fudge applied
Arf filter applied
Total counts in region = 1.56680E+04
Weighted mean angle from optical axis = 5.881 arcmin
-> Standard Output From STOOL group_event_files:1 ad50006000s100112h.evt 13593 1 ad50006000s100612h.evt 13593-> SIS1_OFFCHIP.1 already present in current directory
ad50006000s100112h.evt ad50006000s100612h.evt-> Standard Output From FTOOL xselect:
** XSELECT V1.3 **
!> Enter session name >[xsel] xsel
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS S1CCDPOW
1 W50 EAST BRIGHT2 HIGH 28/04/93 03:44:28 0.18E+05 12482 1111
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS S1CCDPOW
1 W50 EAST BRIGHT2 HIGH 28/04/93 03:44:28 0.18E+05 12482 1111
2 W50 EAST BRIGHT2 HIGH 28/04/93 22:52:12 0.14E+04 1111 1111
EXTRACTOR vers 2.0 11 Apr 1997.
Getting FITS WCS Keywords
Doing file: /data/data17/seq_proc/50006000.007/ad50006000s100112h.evt
Total Good Bad: Region Time Phase Cut
12482 7787 4695 0 0 0
Doing file: /data/data17/seq_proc/50006000.007/ad50006000s100612h.evt
Total Good Bad: Region Time Phase Cut
1111 731 380 0 0 0
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
13593 8518 5075 0 0 0
in 18938.70 seconds
Spectrum has 8518 counts for 0.4498 counts/sec
-------------------------
MANDATORY KEYWORDS/VALUES
-------------------------
--------------------------------------------------------------------
--------------------------------------------------------------------
EXTNAME - SPECTRUM Name of this BINTABLE
TELESCOP - ASCA Mission/Satellite name
INSTRUME - SIS1 Instrument/Detector
FILTER - Instrument filter in use
EXPOSURE - 18939. Integration time (in secs) of PHA data
AREASCAL - 1.0000 Area scaling factor
BACKSCAL - 0.22908 Background scaling factor
BACKFILE - NONE Associated background file
CORRSCAL - 1.0000 Correlation scaling factor
CORRFILE - none Associated correlation file
RESPFILE - NONE Associated redistribution matrix file
ANCRFILE - none Associated ancillary response file
XFLT0001 - none XSPEC selection filter
POISSERR - TRUE Whether Poissonian errors apply
CHANTYPE - PI Whether channels have been corrected
TLMIN1 - 0 First legal Detector channel
DETCHANS - 1024 No. of legal detector channels
NCHAN - 1024 No. of detector channels in dataset
PHAVERSN - 1.1.0 OGIP FITS version number
STAT_ERR - FALSE Statistical Error
SYS_ERR - TRUE Fractional Systematic Error
QUALITY - TRUE Quality Flag
GROUPING - FALSE Grouping Flag
--------------------------------------------------------------------
--------------------------------------------------------------------
... QUALITY
...
... -------
... QUALITY
... -------
... Bad Channels (Channel - Channel)
... ---------------------------------------------
... 0 - 25 have quality 5
... ---------------------------------------------
...
...... exiting, changes written to file : ad50006000s110212_1.pi
EXTRACTOR vers 2.0 11 Apr 1997.
Doing file: /data/data17/seq_proc/50006000.007/ad50006000s100112h.evt
Total Good Bad: Region Time Phase Cut
12482 7787 4695 0 0 0
Writing events file
7787 events written to the output file
Doing file: /data/data17/seq_proc/50006000.007/ad50006000s100612h.evt
Total Good Bad: Region Time Phase Cut
1111 731 380 0 0 0
Writing events file
8518 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
13593 8518 5075 0 0 0
in 18938.70 seconds
Command not found; type ? for a command listing
!xsel:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!xsel:ASCA > set datadir .
Setting data directory to /data/data17/seq_proc/50006000.007/
Setting mkf directory to /data/data17/seq_proc/50006000.007/
!xsel:ASCA > read events ad50006000s100112h.evt
Got new instrument: SIS1
Setting: IMAGE binning = 4
WMAP binning = 8
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 4095
Got the minimum time resolution of the read data: 16.000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data17/seq_proc/50006000.007/
HK Directory is: /data/data17/seq_proc/50006000.007/
!xsel:ASCA-SIS1-BRIGHT2 > read events ad50006000s100612h.evt
Getting Min and Max for Energy Column...
Got min and max for PI: 0 4095
Got the minimum time resolution of the read data: 16.000
Number of files read in: 2
******************** Observation Catalogue ********************
Data Directory is: /data/data17/seq_proc/50006000.007/
HK Directory is: /data/data17/seq_proc/50006000.007/
!xsel:ASCA-SIS1-BRIGHT2 > set phaname PI
!xsel:ASCA-SIS1-BRIGHT2 > filter region ad50006000s132002_1.reg
!xsel:ASCA-SIS1-BRIGHT2 > filter region SIS1_OFFCHIP.1
!xsel:ASCA-SIS1-BRIGHT2 > filter region ad50006000s110212.discrim
!xsel:ASCA-SIS1-BRIGHT2 > extract spectrum
!xsel:ASCA-SIS1-BRIGHT2 > save spectrum ad50006000s110212_1.pi group=yes
Wrote spectrum to ad50006000s110212_1.pi
!xsel:ASCA-SIS1-BRIGHT2 > extract events
!xsel:ASCA-SIS1-BRIGHT2 > save events outfile=events.tmp use_events=yes
Wrote events list to file events.tmp
Changing Data directory from:
/data/data17/seq_proc/50006000.007/
to the current working directory.
!xsel:ASCA-SIS1-BRIGHT2 > exit save_session=no
-> Grouping ad50006000s110212_1.pi to 40 counts/bin------------------------- MANDATORY KEYWORDS/VALUES ------------------------- -------------------------------------------------------------------- -------------------------------------------------------------------- EXTNAME - SPECTRUM Name of this BINTABLE TELESCOP - ASCA Mission/Satellite name INSTRUME - SIS1 Instrument/Detector FILTER - Instrument filter in use EXPOSURE - 18939. Integration time (in secs) of PHA data AREASCAL - 1.0000 Area scaling factor BACKSCAL - 0.22908 Background scaling factor BACKFILE - NONE Associated background file CORRSCAL - 1.0000 Correlation scaling factor CORRFILE - none Associated correlation file RESPFILE - NONE Associated redistribution matrix file ANCRFILE - none Associated ancillary response file XFLT0001 - none XSPEC selection filter POISSERR - TRUE Whether Poissonian errors apply CHANTYPE - PI Whether channels have been corrected TLMIN1 - 0 First legal Detector channel DETCHANS - 1024 No. of legal detector channels NCHAN - 1024 No. of detector channels in dataset PHAVERSN - 1.1.0 OGIP FITS version number STAT_ERR - FALSE Statistical Error SYS_ERR - TRUE Fractional Systematic Error QUALITY - TRUE Quality Flag GROUPING - FALSE Grouping Flag -------------------------------------------------------------------- -------------------------------------------------------------------- ... ... -------- ... GROUPING ... -------- ... --------------------------------------------- ... Channel Grouping (Channel-Channel) : ... 0 - 25 of undefined grouping (Channel quality=bad) ... 26 - 31 are grouped by a factor 6 ... 32 - 43 are grouped by a factor 4 ... 44 - 45 are grouped by a factor 2 ... 46 - 48 are grouped by a factor 3 ... 49 - 54 are grouped by a factor 2 ... 55 - 112 are single channels ... 113 - 114 are grouped by a factor 2 ... 115 - 117 are single channels ... 118 - 119 are grouped by a factor 2 ... 120 - 123 are single channels ... 124 - 125 are grouped by a factor 2 ... 126 - 127 are single channels ... 128 - 149 are grouped by a factor 2 ... 150 - 152 are grouped by a factor 3 ... 153 - 154 are grouped by a factor 2 ... 155 - 172 are grouped by a factor 3 ... 173 - 174 are grouped by a factor 2 ... 175 - 177 are grouped by a factor 3 ... 178 - 181 are grouped by a factor 4 ... 182 - 184 are grouped by a factor 3 ... 185 - 192 are grouped by a factor 4 ... 193 - 195 are grouped by a factor 3 ... 196 - 203 are grouped by a factor 4 ... 204 - 206 are grouped by a factor 3 ... 207 - 210 are grouped by a factor 4 ... 211 - 213 are grouped by a factor 3 ... 214 - 217 are grouped by a factor 4 ... 218 - 220 are grouped by a factor 3 ... 221 - 230 are grouped by a factor 5 ... 231 - 234 are grouped by a factor 4 ... 235 - 237 are grouped by a factor 3 ... 238 - 241 are grouped by a factor 4 ... 242 - 246 are grouped by a factor 5 ... 247 - 250 are grouped by a factor 4 ... 251 - 265 are grouped by a factor 5 ... 266 - 269 are grouped by a factor 4 ... 270 - 284 are grouped by a factor 5 ... 285 - 291 are grouped by a factor 7 ... 292 - 299 are grouped by a factor 8 ... 300 - 317 are grouped by a factor 6 ... 318 - 324 are grouped by a factor 7 ... 325 - 330 are grouped by a factor 6 ... 331 - 366 are grouped by a factor 9 ... 367 - 379 are grouped by a factor 13 ... 380 - 391 are grouped by a factor 12 ... 392 - 408 are grouped by a factor 17 ... 409 - 424 are grouped by a factor 16 ... 425 - 435 are grouped by a factor 11 ... 436 - 455 are grouped by a factor 20 ... 456 - 472 are grouped by a factor 17 ... 473 - 497 are grouped by a factor 25 ... 498 - 521 are grouped by a factor 24 ... 522 - 568 are grouped by a factor 47 ... 569 - 620 are grouped by a factor 52 ... 621 - 676 are grouped by a factor 56 ... 677 - 776 are grouped by a factor 100 ... 777 - 851 are grouped by a factor 75 ... 852 - 870 are grouped by a factor 19 ... 871 - 876 are grouped by a factor 6 ... 877 - 887 are grouped by a factor 11 ... 888 - 902 are grouped by a factor 15 ... 903 - 941 are grouped by a factor 39 ... 942 - 955 are grouped by a factor 14 ... --------------------------------------------- ... ...... exiting, changes written to file : ad50006000s110212_1.pi ** grppha 2.6.0 completed successfully-> Source occupies chip(s) 0 1 2 3
** XSELECT V1.3 **
!> Enter session name >[xsel] xsel
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS S1CCDPOW
1 W50 EAST BRIGHT2 HIGH 28/04/93 03:44:28 0.19E+05 8518 1111
EXTRACTOR vers 2.0 11 Apr 1997.
Getting FITS WCS Keywords
Doing file: /data/data17/seq_proc/50006000.007/events.tmp
Total Good Bad: Region Time Phase Cut
8518 206 8312 0 0 0
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
8518 206 8312 0 0 0
in 18938.70 seconds
Spectrum has 206 counts for 1.0877E-02 counts/sec
-------------------------
MANDATORY KEYWORDS/VALUES
-------------------------
--------------------------------------------------------------------
--------------------------------------------------------------------
EXTNAME - SPECTRUM Name of this BINTABLE
TELESCOP - ASCA Mission/Satellite name
INSTRUME - SIS1 Instrument/Detector
FILTER - Instrument filter in use
EXPOSURE - 18939. Integration time (in secs) of PHA data
AREASCAL - 1.0000 Area scaling factor
BACKSCAL - 3.61719E-02 Background scaling factor
BACKFILE - NONE Associated background file
CORRSCAL - 1.0000 Correlation scaling factor
CORRFILE - none Associated correlation file
RESPFILE - NONE Associated redistribution matrix file
ANCRFILE - none Associated ancillary response file
XFLT0001 - none XSPEC selection filter
POISSERR - TRUE Whether Poissonian errors apply
CHANTYPE - PI Whether channels have been corrected
TLMIN1 - 0 First legal Detector channel
DETCHANS - 1024 No. of legal detector channels
NCHAN - 1024 No. of detector channels in dataset
PHAVERSN - 1.1.0 OGIP FITS version number
STAT_ERR - FALSE Statistical Error
SYS_ERR - TRUE Fractional Systematic Error
QUALITY - TRUE Quality Flag
GROUPING - FALSE Grouping Flag
--------------------------------------------------------------------
--------------------------------------------------------------------
... QUALITY
...
... -------
... QUALITY
... -------
... Bad Channels (Channel - Channel)
... ---------------------------------------------
... 0 - 25 have quality 5
... ---------------------------------------------
...
...... exiting, changes written to file : spec0.tmp
Command not found; type ? for a command listing
!xsel:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!xsel:ASCA > set datadir .
Setting data directory to /data/data17/seq_proc/50006000.007/
Setting mkf directory to /data/data17/seq_proc/50006000.007/
!xsel:ASCA > read events events.tmp
Got new instrument: SIS1
Setting: IMAGE binning = 4
WMAP binning = 8
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 4095
Got the minimum time resolution of the read data: 16.000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data17/seq_proc/50006000.007/
HK Directory is: /data/data17/seq_proc/50006000.007/
!xsel:ASCA-SIS1-BRIGHT2 > set phaname PI
!xsel:ASCA-SIS1-BRIGHT2 > filter region ad50006000s132002_1.reg
!xsel:ASCA-SIS1-BRIGHT2 > filter region SIS1_OFFCHIP.1
!xsel:ASCA-SIS1-BRIGHT2 > filter region ad50006000s110212.discrim
!xsel:ASCA-SIS1-BRIGHT2 > filter region SIS1_NOTCHIP1.1
!xsel:ASCA-SIS1-BRIGHT2 > filter region SIS1_NOTCHIP2.1
!xsel:ASCA-SIS1-BRIGHT2 > filter region SIS1_NOTCHIP3.1
!xsel:ASCA-SIS1-BRIGHT2 > extract spectrum
!xsel:ASCA-SIS1-BRIGHT2 > save spectrum spec0.tmp group=yes
Wrote spectrum to spec0.tmp
!xsel:ASCA-SIS1-BRIGHT2 > exit save_session=no
-> sis1c0p40_290296.fits already present in current directorySisrmg Version 1.1, Configured 04/97 This version resolves *all* known keyword incompatibilities with other FTOOLS tasks. If you have previously fudged *any* keywords in the PHA file to compensate, incorrect results will follow. Setting 1st PHA channel to 0 Making v1.1 1180x1024 S1C0 Bright2 PI RMF Calibration data from ./ Please stand by... ...Done.-> SIS1_NOTCHIP0.1 already present in current directory
** XSELECT V1.3 **
!> Enter session name >[xsel] xsel
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS S1CCDPOW
1 W50 EAST BRIGHT2 HIGH 28/04/93 03:44:28 0.19E+05 8518 1111
EXTRACTOR vers 2.0 11 Apr 1997.
Getting FITS WCS Keywords
Doing file: /data/data17/seq_proc/50006000.007/events.tmp
Total Good Bad: Region Time Phase Cut
8518 1297 7221 0 0 0
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
8518 1297 7221 0 0 0
in 18938.70 seconds
Spectrum has 1297 counts for 6.8484E-02 counts/sec
-------------------------
MANDATORY KEYWORDS/VALUES
-------------------------
--------------------------------------------------------------------
--------------------------------------------------------------------
EXTNAME - SPECTRUM Name of this BINTABLE
TELESCOP - ASCA Mission/Satellite name
INSTRUME - SIS1 Instrument/Detector
FILTER - Instrument filter in use
EXPOSURE - 18939. Integration time (in secs) of PHA data
AREASCAL - 1.0000 Area scaling factor
BACKSCAL - 8.13672E-02 Background scaling factor
BACKFILE - NONE Associated background file
CORRSCAL - 1.0000 Correlation scaling factor
CORRFILE - none Associated correlation file
RESPFILE - NONE Associated redistribution matrix file
ANCRFILE - none Associated ancillary response file
XFLT0001 - none XSPEC selection filter
POISSERR - TRUE Whether Poissonian errors apply
CHANTYPE - PI Whether channels have been corrected
TLMIN1 - 0 First legal Detector channel
DETCHANS - 1024 No. of legal detector channels
NCHAN - 1024 No. of detector channels in dataset
PHAVERSN - 1.1.0 OGIP FITS version number
STAT_ERR - FALSE Statistical Error
SYS_ERR - TRUE Fractional Systematic Error
QUALITY - TRUE Quality Flag
GROUPING - FALSE Grouping Flag
--------------------------------------------------------------------
--------------------------------------------------------------------
... QUALITY
...
... -------
... QUALITY
... -------
... Bad Channels (Channel - Channel)
... ---------------------------------------------
... 0 - 25 have quality 5
... ---------------------------------------------
...
...... exiting, changes written to file : spec1.tmp
Command not found; type ? for a command listing
!xsel:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!xsel:ASCA > set datadir .
Setting data directory to /data/data17/seq_proc/50006000.007/
Setting mkf directory to /data/data17/seq_proc/50006000.007/
!xsel:ASCA > read events events.tmp
Got new instrument: SIS1
Setting: IMAGE binning = 4
WMAP binning = 8
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 4095
Got the minimum time resolution of the read data: 16.000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data17/seq_proc/50006000.007/
HK Directory is: /data/data17/seq_proc/50006000.007/
!xsel:ASCA-SIS1-BRIGHT2 > set phaname PI
!xsel:ASCA-SIS1-BRIGHT2 > filter region ad50006000s132002_1.reg
!xsel:ASCA-SIS1-BRIGHT2 > filter region SIS1_OFFCHIP.1
!xsel:ASCA-SIS1-BRIGHT2 > filter region ad50006000s110212.discrim
!xsel:ASCA-SIS1-BRIGHT2 > filter region SIS1_NOTCHIP0.1
!xsel:ASCA-SIS1-BRIGHT2 > filter region SIS1_NOTCHIP2.1
!xsel:ASCA-SIS1-BRIGHT2 > filter region SIS1_NOTCHIP3.1
!xsel:ASCA-SIS1-BRIGHT2 > extract spectrum
!xsel:ASCA-SIS1-BRIGHT2 > save spectrum spec1.tmp group=yes
Wrote spectrum to spec1.tmp
!xsel:ASCA-SIS1-BRIGHT2 > exit save_session=no
-> sis1c1p40_290296.fits already present in current directorySisrmg Version 1.1, Configured 04/97 This version resolves *all* known keyword incompatibilities with other FTOOLS tasks. If you have previously fudged *any* keywords in the PHA file to compensate, incorrect results will follow. Setting 1st PHA channel to 0 Making v1.1 1180x1024 S1C1 Bright2 PI RMF Calibration data from ./ Please stand by... ...Done.-> SIS1_NOTCHIP0.1 already present in current directory
** XSELECT V1.3 **
!> Enter session name >[xsel] xsel
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS S1CCDPOW
1 W50 EAST BRIGHT2 HIGH 28/04/93 03:44:28 0.19E+05 8518 1111
EXTRACTOR vers 2.0 11 Apr 1997.
Getting FITS WCS Keywords
Doing file: /data/data17/seq_proc/50006000.007/events.tmp
Total Good Bad: Region Time Phase Cut
8518 5599 2919 0 0 0
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
8518 5599 2919 0 0 0
in 18938.70 seconds
Spectrum has 5599 counts for 0.2956 counts/sec
-------------------------
MANDATORY KEYWORDS/VALUES
-------------------------
--------------------------------------------------------------------
--------------------------------------------------------------------
EXTNAME - SPECTRUM Name of this BINTABLE
TELESCOP - ASCA Mission/Satellite name
INSTRUME - SIS1 Instrument/Detector
FILTER - Instrument filter in use
EXPOSURE - 18939. Integration time (in secs) of PHA data
AREASCAL - 1.0000 Area scaling factor
BACKSCAL - 0.13381 Background scaling factor
BACKFILE - NONE Associated background file
CORRSCAL - 1.0000 Correlation scaling factor
CORRFILE - none Associated correlation file
RESPFILE - NONE Associated redistribution matrix file
ANCRFILE - none Associated ancillary response file
XFLT0001 - none XSPEC selection filter
POISSERR - TRUE Whether Poissonian errors apply
CHANTYPE - PI Whether channels have been corrected
TLMIN1 - 0 First legal Detector channel
DETCHANS - 1024 No. of legal detector channels
NCHAN - 1024 No. of detector channels in dataset
PHAVERSN - 1.1.0 OGIP FITS version number
STAT_ERR - FALSE Statistical Error
SYS_ERR - TRUE Fractional Systematic Error
QUALITY - TRUE Quality Flag
GROUPING - FALSE Grouping Flag
--------------------------------------------------------------------
--------------------------------------------------------------------
... QUALITY
...
... -------
... QUALITY
... -------
... Bad Channels (Channel - Channel)
... ---------------------------------------------
... 0 - 25 have quality 5
... ---------------------------------------------
...
...... exiting, changes written to file : spec2.tmp
Command not found; type ? for a command listing
!xsel:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!xsel:ASCA > set datadir .
Setting data directory to /data/data17/seq_proc/50006000.007/
Setting mkf directory to /data/data17/seq_proc/50006000.007/
!xsel:ASCA > read events events.tmp
Got new instrument: SIS1
Setting: IMAGE binning = 4
WMAP binning = 8
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 4095
Got the minimum time resolution of the read data: 16.000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data17/seq_proc/50006000.007/
HK Directory is: /data/data17/seq_proc/50006000.007/
!xsel:ASCA-SIS1-BRIGHT2 > set phaname PI
!xsel:ASCA-SIS1-BRIGHT2 > filter region ad50006000s132002_1.reg
!xsel:ASCA-SIS1-BRIGHT2 > filter region SIS1_OFFCHIP.1
!xsel:ASCA-SIS1-BRIGHT2 > filter region ad50006000s110212.discrim
!xsel:ASCA-SIS1-BRIGHT2 > filter region SIS1_NOTCHIP0.1
!xsel:ASCA-SIS1-BRIGHT2 > filter region SIS1_NOTCHIP1.1
!xsel:ASCA-SIS1-BRIGHT2 > filter region SIS1_NOTCHIP3.1
!xsel:ASCA-SIS1-BRIGHT2 > extract spectrum
!xsel:ASCA-SIS1-BRIGHT2 > save spectrum spec2.tmp group=yes
Wrote spectrum to spec2.tmp
!xsel:ASCA-SIS1-BRIGHT2 > exit save_session=no
-> sis1c2p40_290296.fits already present in current directorySisrmg Version 1.1, Configured 04/97 This version resolves *all* known keyword incompatibilities with other FTOOLS tasks. If you have previously fudged *any* keywords in the PHA file to compensate, incorrect results will follow. Setting 1st PHA channel to 0 Making v1.1 1180x1024 S1C2 Bright2 PI RMF Calibration data from ./ Please stand by... ...Done.-> SIS1_NOTCHIP0.1 already present in current directory
** XSELECT V1.3 **
!> Enter session name >[xsel] xsel
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS S1CCDPOW
1 W50 EAST BRIGHT2 HIGH 28/04/93 03:44:28 0.19E+05 8518 1111
EXTRACTOR vers 2.0 11 Apr 1997.
Getting FITS WCS Keywords
Doing file: /data/data17/seq_proc/50006000.007/events.tmp
Total Good Bad: Region Time Phase Cut
8518 1416 7102 0 0 0
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
8518 1416 7102 0 0 0
in 18938.70 seconds
Spectrum has 1416 counts for 7.4768E-02 counts/sec
-------------------------
MANDATORY KEYWORDS/VALUES
-------------------------
--------------------------------------------------------------------
--------------------------------------------------------------------
EXTNAME - SPECTRUM Name of this BINTABLE
TELESCOP - ASCA Mission/Satellite name
INSTRUME - SIS1 Instrument/Detector
FILTER - Instrument filter in use
EXPOSURE - 18939. Integration time (in secs) of PHA data
AREASCAL - 1.0000 Area scaling factor
BACKSCAL - 6.53027E-02 Background scaling factor
BACKFILE - NONE Associated background file
CORRSCAL - 1.0000 Correlation scaling factor
CORRFILE - none Associated correlation file
RESPFILE - NONE Associated redistribution matrix file
ANCRFILE - none Associated ancillary response file
XFLT0001 - none XSPEC selection filter
POISSERR - TRUE Whether Poissonian errors apply
CHANTYPE - PI Whether channels have been corrected
TLMIN1 - 0 First legal Detector channel
DETCHANS - 1024 No. of legal detector channels
NCHAN - 1024 No. of detector channels in dataset
PHAVERSN - 1.1.0 OGIP FITS version number
STAT_ERR - FALSE Statistical Error
SYS_ERR - TRUE Fractional Systematic Error
QUALITY - TRUE Quality Flag
GROUPING - FALSE Grouping Flag
--------------------------------------------------------------------
--------------------------------------------------------------------
... QUALITY
...
... -------
... QUALITY
... -------
... Bad Channels (Channel - Channel)
... ---------------------------------------------
... 0 - 25 have quality 5
... ---------------------------------------------
...
...... exiting, changes written to file : spec3.tmp
Command not found; type ? for a command listing
!xsel:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!xsel:ASCA > set datadir .
Setting data directory to /data/data17/seq_proc/50006000.007/
Setting mkf directory to /data/data17/seq_proc/50006000.007/
!xsel:ASCA > read events events.tmp
Got new instrument: SIS1
Setting: IMAGE binning = 4
WMAP binning = 8
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 4095
Got the minimum time resolution of the read data: 16.000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data17/seq_proc/50006000.007/
HK Directory is: /data/data17/seq_proc/50006000.007/
!xsel:ASCA-SIS1-BRIGHT2 > set phaname PI
!xsel:ASCA-SIS1-BRIGHT2 > filter region ad50006000s132002_1.reg
!xsel:ASCA-SIS1-BRIGHT2 > filter region SIS1_OFFCHIP.1
!xsel:ASCA-SIS1-BRIGHT2 > filter region ad50006000s110212.discrim
!xsel:ASCA-SIS1-BRIGHT2 > filter region SIS1_NOTCHIP0.1
!xsel:ASCA-SIS1-BRIGHT2 > filter region SIS1_NOTCHIP1.1
!xsel:ASCA-SIS1-BRIGHT2 > filter region SIS1_NOTCHIP2.1
!xsel:ASCA-SIS1-BRIGHT2 > extract spectrum
!xsel:ASCA-SIS1-BRIGHT2 > save spectrum spec3.tmp group=yes
Wrote spectrum to spec3.tmp
!xsel:ASCA-SIS1-BRIGHT2 > exit save_session=no
-> sis1c3p40_290296.fits already present in current directorySisrmg Version 1.1, Configured 04/97 This version resolves *all* known keyword incompatibilities with other FTOOLS tasks. If you have previously fudged *any* keywords in the PHA file to compensate, incorrect results will follow. Setting 1st PHA channel to 0 Making v1.1 1180x1024 S1C3 Bright2 PI RMF Calibration data from ./ Please stand by... ...Done.-> Chip weights:
rmf0.tmp 0.0241840807701338 rmf1.tmp 0.152265790091571 rmf2.tmp 0.65731392345621 rmf3.tmp 0.166236205682085-> Standard Output From FTOOL addrmf:
ADDRMF vers 1.10 10 April, 1997.
Summing ...
2.418E-02 * rmf0.tmp
1.523E-01 * rmf1.tmp
6.573E-01 * rmf2.tmp
1.662E-01 * rmf3.tmp
RMF # 1 : rmf0.tmp 0.02
ASCA SIS1 NONE NONE PI
RMF # 2 : rmf1.tmp 0.15
ASCA SIS1 NONE NONE PI
RMF # 3 : rmf2.tmp 0.66
ASCA SIS1 NONE NONE PI
RMF # 4 : rmf3.tmp 0.17
ASCA SIS1 NONE NONE PI
-> Generating ad50006000s110212_1.arf with point=no
ASCAARF vers 2.72 14 Mar 1997.
Input WMAP array has size 82 by 99 bins
expanded to 82 by 99 bins
First WMAP bin is at detector pixel 224 464
8 detector pixels per WMAP bin
WMAP bin size is 0.21600 mm
0.21216 arcmin
Selected region size is 263.97 arcmin^2
Optical axis is detector pixel 618.28 773.83
1180 energies from RMF file
Effective area fudge applied
Arf filter applied
Total counts in region = 8.38100E+03
Weighted mean angle from optical axis = 5.836 arcmin
-> Standard Output From STOOL group_event_files:1 ad50006000g200170m.evt 24469 1 ad50006000g200270h.evt 24469 1 ad50006000g200470m.evt 24469 1 ad50006000g200570h.evt 24469-> GIS2_REGION256_OFF.4 already present in current directory
ad50006000g200170m.evt ad50006000g200270h.evt ad50006000g200470m.evt ad50006000g200570h.evt-> Standard Output From FTOOL xselect:
** XSELECT V1.3 **
!> Enter session name >[xsel] xsel
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS PHA_BINS
1 W50 EAST PH MEDIUM 27/04/93 23:50:48 0.12E+05 7555 1024
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS PHA_BINS
1 W50 EAST PH MEDIUM 27/04/93 23:50:48 0.12E+05 7555 1024
2 W50 EAST PH HIGH 28/04/93 03:44:46 0.18E+05 11655 1024
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS PHA_BINS
1 W50 EAST PH MEDIUM 27/04/93 23:50:48 0.12E+05 7555 1024
2 W50 EAST PH HIGH 28/04/93 03:44:46 0.18E+05 11655 1024
3 W50 EAST PH MEDIUM 28/04/93 19:50:32 0.68E+04 4255 1024
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS PHA_BINS
1 W50 EAST PH MEDIUM 27/04/93 23:50:48 0.12E+05 7555 1024
2 W50 EAST PH HIGH 28/04/93 03:44:46 0.18E+05 11655 1024
3 W50 EAST PH MEDIUM 28/04/93 19:50:32 0.68E+04 4255 1024
4 W50 EAST PH HIGH 28/04/93 22:52:30 0.15E+04 1004 1024
EXTRACTOR vers 2.0 11 Apr 1997.
Getting FITS WCS Keywords
Doing file: /data/data17/seq_proc/50006000.007/ad50006000g200170m.evt
Total Good Bad: Region Time Phase Cut
7555 2557 4998 0 0 0
Doing file: /data/data17/seq_proc/50006000.007/ad50006000g200270h.evt
Total Good Bad: Region Time Phase Cut
11655 4030 7625 0 0 0
Doing file: /data/data17/seq_proc/50006000.007/ad50006000g200470m.evt
Total Good Bad: Region Time Phase Cut
4255 1431 2824 0 0 0
Doing file: /data/data17/seq_proc/50006000.007/ad50006000g200570h.evt
Total Good Bad: Region Time Phase Cut
1004 360 644 0 0 0
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
24469 8378 16091 0 0 0
in 37693.54 seconds
Spectrum has 8378 counts for 0.2223 counts/sec
-------------------------
MANDATORY KEYWORDS/VALUES
-------------------------
--------------------------------------------------------------------
--------------------------------------------------------------------
EXTNAME - SPECTRUM Name of this BINTABLE
TELESCOP - ASCA Mission/Satellite name
INSTRUME - GIS2 Instrument/Detector
FILTER - Instrument filter in use
EXPOSURE - 37694. Integration time (in secs) of PHA data
AREASCAL - 1.0000 Area scaling factor
BACKSCAL - 5.44586E-02 Background scaling factor
BACKFILE - NONE Associated background file
CORRSCAL - 1.0000 Correlation scaling factor
CORRFILE - none Associated correlation file
RESPFILE - NONE Associated redistribution matrix file
ANCRFILE - none Associated ancillary response file
XFLT0001 - none XSPEC selection filter
POISSERR - TRUE Whether Poissonian errors apply
CHANTYPE - PI Whether channels have been corrected
TLMIN1 - 0 First legal Detector channel
DETCHANS - 1024 No. of legal detector channels
NCHAN - 1024 No. of detector channels in dataset
PHAVERSN - 1992a OGIP FITS version number
STAT_ERR - FALSE Statistical Error
SYS_ERR - TRUE Fractional Systematic Error
QUALITY - TRUE Quality Flag
GROUPING - FALSE Grouping Flag
--------------------------------------------------------------------
--------------------------------------------------------------------
...
... --------
... GROUPING
... --------
... ---------------------------------------------
... Channel Grouping (Channel-Channel) :
... ---------------------------------------------
...
...... exiting, changes written to file : ad50006000g210170_1.pi
Command not found; type ? for a command listing
!xsel:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!xsel:ASCA > set datadir .
Setting data directory to /data/data17/seq_proc/50006000.007/
Setting mkf directory to /data/data17/seq_proc/50006000.007/
!xsel:ASCA > read events ad50006000g200170m.evt
Got new instrument: GIS2
Setting: IMAGE binning = 1
WMAP binning = 1
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 1023
Got the minimum time resolution of the read data: 0.50000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data17/seq_proc/50006000.007/
HK Directory is: /data/data17/seq_proc/50006000.007/
!xsel:ASCA-GIS2-PH > read events ad50006000g200270h.evt
Getting Min and Max for Energy Column...
Got min and max for PI: 0 1023
Got the minimum time resolution of the read data: 0.62500E-01
Number of files read in: 2
******************** Observation Catalogue ********************
Data Directory is: /data/data17/seq_proc/50006000.007/
HK Directory is: /data/data17/seq_proc/50006000.007/
!xsel:ASCA-GIS2-PH > read events ad50006000g200470m.evt
Getting Min and Max for Energy Column...
Got min and max for PI: 0 1023
Got the minimum time resolution of the read data: 0.50000
Number of files read in: 3
******************** Observation Catalogue ********************
Data Directory is: /data/data17/seq_proc/50006000.007/
HK Directory is: /data/data17/seq_proc/50006000.007/
!xsel:ASCA-GIS2-PH > read events ad50006000g200570h.evt
Getting Min and Max for Energy Column...
Got min and max for PI: 0 1023
Got the minimum time resolution of the read data: 0.62500E-01
Number of files read in: 4
******************** Observation Catalogue ********************
Data Directory is: /data/data17/seq_proc/50006000.007/
HK Directory is: /data/data17/seq_proc/50006000.007/
!xsel:ASCA-GIS2-PH > set phaname PI
!xsel:ASCA-GIS2-PH > filter region ad50006000g225670_1.reg
!xsel:ASCA-GIS2-PH > filter region GIS2_REGION256_OFF.4
!xsel:ASCA-GIS2-PH > extract spectrum
!xsel:ASCA-GIS2-PH > save spectrum ad50006000g210170_1.pi group=yes
Wrote spectrum to ad50006000g210170_1.pi
!xsel:ASCA-GIS2-PH > exit save_session=no
-> Correcting ad50006000g210170_1.pi for dead time... read all the files from deadlist.tmp-> Grouping ad50006000g210170_1.pi to 40 counts/bin
------------------------- MANDATORY KEYWORDS/VALUES ------------------------- -------------------------------------------------------------------- -------------------------------------------------------------------- EXTNAME - SPECTRUM Name of this BINTABLE TELESCOP - ASCA Mission/Satellite name INSTRUME - GIS2 Instrument/Detector FILTER - Instrument filter in use EXPOSURE - 37694. Integration time (in secs) of PHA data AREASCAL - 1.0000 Area scaling factor BACKSCAL - 5.44586E-02 Background scaling factor BACKFILE - NONE Associated background file CORRSCAL - 1.0000 Correlation scaling factor CORRFILE - none Associated correlation file RESPFILE - NONE Associated redistribution matrix file ANCRFILE - none Associated ancillary response file XFLT0001 - none XSPEC selection filter POISSERR - TRUE Whether Poissonian errors apply CHANTYPE - PI Whether channels have been corrected TLMIN1 - 0 First legal Detector channel DETCHANS - 1024 No. of legal detector channels NCHAN - 1024 No. of detector channels in dataset PHAVERSN - 1.1.0 OGIP FITS version number STAT_ERR - FALSE Statistical Error SYS_ERR - TRUE Fractional Systematic Error QUALITY - TRUE Quality Flag GROUPING - TRUE Grouping Flag -------------------------------------------------------------------- -------------------------------------------------------------------- ... ... -------- ... GROUPING ... -------- ... --------------------------------------------- ... Channel Grouping (Channel-Channel) : ... 0 - 23 are grouped by a factor 24 ... 24 - 31 are grouped by a factor 4 ... 32 - 43 are grouped by a factor 6 ... 44 - 48 are grouped by a factor 5 ... 49 - 52 are grouped by a factor 4 ... 53 - 62 are grouped by a factor 5 ... 63 - 65 are grouped by a factor 3 ... 66 - 69 are grouped by a factor 4 ... 70 - 71 are grouped by a factor 2 ... 72 - 74 are grouped by a factor 3 ... 75 - 80 are grouped by a factor 2 ... 81 - 83 are grouped by a factor 3 ... 84 - 103 are grouped by a factor 2 ... 104 - 105 are single channels ... 106 - 115 are grouped by a factor 2 ... 116 - 116 are single channels ... 117 - 124 are grouped by a factor 2 ... 125 - 127 are single channels ... 128 - 133 are grouped by a factor 2 ... 134 - 134 are single channels ... 135 - 136 are grouped by a factor 2 ... 137 - 141 are single channels ... 142 - 143 are grouped by a factor 2 ... 144 - 147 are single channels ... 148 - 153 are grouped by a factor 2 ... 154 - 155 are single channels ... 156 - 165 are grouped by a factor 2 ... 166 - 166 are single channels ... 167 - 168 are grouped by a factor 2 ... 169 - 170 are single channels ... 171 - 174 are grouped by a factor 2 ... 175 - 175 are single channels ... 176 - 195 are grouped by a factor 2 ... 196 - 204 are grouped by a factor 3 ... 205 - 206 are grouped by a factor 2 ... 207 - 212 are grouped by a factor 3 ... 213 - 216 are grouped by a factor 2 ... 217 - 225 are grouped by a factor 3 ... 226 - 229 are grouped by a factor 4 ... 230 - 231 are grouped by a factor 2 ... 232 - 234 are grouped by a factor 3 ... 235 - 236 are grouped by a factor 2 ... 237 - 260 are grouped by a factor 3 ... 261 - 268 are grouped by a factor 4 ... 269 - 277 are grouped by a factor 3 ... 278 - 281 are grouped by a factor 4 ... 282 - 287 are grouped by a factor 3 ... 288 - 303 are grouped by a factor 4 ... 304 - 313 are grouped by a factor 5 ... 314 - 317 are grouped by a factor 4 ... 318 - 342 are grouped by a factor 5 ... 343 - 346 are grouped by a factor 4 ... 347 - 351 are grouped by a factor 5 ... 352 - 355 are grouped by a factor 4 ... 356 - 369 are grouped by a factor 7 ... 370 - 374 are grouped by a factor 5 ... 375 - 392 are grouped by a factor 6 ... 393 - 397 are grouped by a factor 5 ... 398 - 404 are grouped by a factor 7 ... 405 - 412 are grouped by a factor 8 ... 413 - 419 are grouped by a factor 7 ... 420 - 428 are grouped by a factor 9 ... 429 - 436 are grouped by a factor 8 ... 437 - 441 are grouped by a factor 5 ... 442 - 449 are grouped by a factor 8 ... 450 - 458 are grouped by a factor 9 ... 459 - 468 are grouped by a factor 10 ... 469 - 507 are grouped by a factor 13 ... 508 - 524 are grouped by a factor 17 ... 525 - 537 are grouped by a factor 13 ... 538 - 556 are grouped by a factor 19 ... 557 - 567 are grouped by a factor 11 ... 568 - 589 are grouped by a factor 22 ... 590 - 607 are grouped by a factor 18 ... 608 - 628 are grouped by a factor 21 ... 629 - 660 are grouped by a factor 32 ... 661 - 686 are grouped by a factor 26 ... 687 - 719 are grouped by a factor 33 ... 720 - 762 are grouped by a factor 43 ... 763 - 834 are grouped by a factor 72 ... 835 - 929 are grouped by a factor 95 ... 930 - 1023 of undefined grouping (Channel quality=bad) ... --------------------------------------------- ... ...... exiting, changes written to file : ad50006000g210170_1.pi ** grppha 2.6.0 completed successfully-> Fetching gis2v4_0.rmf
ASCAARF vers 2.72 14 Mar 1997.
Input WMAP array has size 67 by 67 bins
expanded to 128 by 128 bins
First WMAP bin is at detector pixel 46 87
1 detector pixels per WMAP bin
WMAP bin size is 0.25000 mm
0.24555 arcmin
Selected region size is 215.24 arcmin^2
Optical axis is detector pixel 133.00 130.96
201 energies from RMF file
Effective area fudge applied
Arf filter applied
Total counts in region = 8.37800E+03
Weighted mean angle from optical axis = 8.071 arcmin
-> Standard Output From STOOL group_event_files:1 ad50006000g300170m.evt 23962 1 ad50006000g300270h.evt 23962 1 ad50006000g300470m.evt 23962 1 ad50006000g300570h.evt 23962-> GIS3_REGION256_OFF.4 already present in current directory
ad50006000g300170m.evt ad50006000g300270h.evt ad50006000g300470m.evt ad50006000g300570h.evt-> Standard Output From FTOOL xselect:
** XSELECT V1.3 **
!> Enter session name >[xsel] xsel
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS PHA_BINS
1 W50 EAST PH MEDIUM 27/04/93 23:50:48 0.12E+05 7421 1024
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS PHA_BINS
1 W50 EAST PH MEDIUM 27/04/93 23:50:48 0.12E+05 7421 1024
2 W50 EAST PH HIGH 28/04/93 03:44:46 0.18E+05 11260 1024
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS PHA_BINS
1 W50 EAST PH MEDIUM 27/04/93 23:50:48 0.12E+05 7421 1024
2 W50 EAST PH HIGH 28/04/93 03:44:46 0.18E+05 11260 1024
3 W50 EAST PH MEDIUM 28/04/93 19:50:32 0.68E+04 4275 1024
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS PHA_BINS
1 W50 EAST PH MEDIUM 27/04/93 23:50:48 0.12E+05 7421 1024
2 W50 EAST PH HIGH 28/04/93 03:44:46 0.18E+05 11260 1024
3 W50 EAST PH MEDIUM 28/04/93 19:50:32 0.68E+04 4275 1024
4 W50 EAST PH HIGH 28/04/93 22:52:30 0.15E+04 1006 1024
EXTRACTOR vers 2.0 11 Apr 1997.
Getting FITS WCS Keywords
Doing file: /data/data17/seq_proc/50006000.007/ad50006000g300170m.evt
Total Good Bad: Region Time Phase Cut
7421 3081 4340 0 0 0
Doing file: /data/data17/seq_proc/50006000.007/ad50006000g300270h.evt
Total Good Bad: Region Time Phase Cut
11260 4708 6552 0 0 0
Doing file: /data/data17/seq_proc/50006000.007/ad50006000g300470m.evt
Total Good Bad: Region Time Phase Cut
4275 1796 2479 0 0 0
Doing file: /data/data17/seq_proc/50006000.007/ad50006000g300570h.evt
Total Good Bad: Region Time Phase Cut
1006 441 565 0 0 0
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
23962 10026 13936 0 0 0
in 37697.54 seconds
Spectrum has 10026 counts for 0.2660 counts/sec
-------------------------
MANDATORY KEYWORDS/VALUES
-------------------------
--------------------------------------------------------------------
--------------------------------------------------------------------
EXTNAME - SPECTRUM Name of this BINTABLE
TELESCOP - ASCA Mission/Satellite name
INSTRUME - GIS3 Instrument/Detector
FILTER - Instrument filter in use
EXPOSURE - 37698. Integration time (in secs) of PHA data
AREASCAL - 1.0000 Area scaling factor
BACKSCAL - 5.44586E-02 Background scaling factor
BACKFILE - NONE Associated background file
CORRSCAL - 1.0000 Correlation scaling factor
CORRFILE - none Associated correlation file
RESPFILE - NONE Associated redistribution matrix file
ANCRFILE - none Associated ancillary response file
XFLT0001 - none XSPEC selection filter
POISSERR - TRUE Whether Poissonian errors apply
CHANTYPE - PI Whether channels have been corrected
TLMIN1 - 0 First legal Detector channel
DETCHANS - 1024 No. of legal detector channels
NCHAN - 1024 No. of detector channels in dataset
PHAVERSN - 1992a OGIP FITS version number
STAT_ERR - FALSE Statistical Error
SYS_ERR - TRUE Fractional Systematic Error
QUALITY - TRUE Quality Flag
GROUPING - FALSE Grouping Flag
--------------------------------------------------------------------
--------------------------------------------------------------------
...
... --------
... GROUPING
... --------
... ---------------------------------------------
... Channel Grouping (Channel-Channel) :
... ---------------------------------------------
...
...... exiting, changes written to file : ad50006000g310170_1.pi
Command not found; type ? for a command listing
!xsel:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!xsel:ASCA > set datadir .
Setting data directory to /data/data17/seq_proc/50006000.007/
Setting mkf directory to /data/data17/seq_proc/50006000.007/
!xsel:ASCA > read events ad50006000g300170m.evt
Got new instrument: GIS3
Setting: IMAGE binning = 1
WMAP binning = 1
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 1023
Got the minimum time resolution of the read data: 0.50000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data17/seq_proc/50006000.007/
HK Directory is: /data/data17/seq_proc/50006000.007/
!xsel:ASCA-GIS3-PH > read events ad50006000g300270h.evt
Getting Min and Max for Energy Column...
Got min and max for PI: 0 1023
Got the minimum time resolution of the read data: 0.62500E-01
Number of files read in: 2
******************** Observation Catalogue ********************
Data Directory is: /data/data17/seq_proc/50006000.007/
HK Directory is: /data/data17/seq_proc/50006000.007/
!xsel:ASCA-GIS3-PH > read events ad50006000g300470m.evt
Getting Min and Max for Energy Column...
Got min and max for PI: 0 1023
Got the minimum time resolution of the read data: 0.50000
Number of files read in: 3
******************** Observation Catalogue ********************
Data Directory is: /data/data17/seq_proc/50006000.007/
HK Directory is: /data/data17/seq_proc/50006000.007/
!xsel:ASCA-GIS3-PH > read events ad50006000g300570h.evt
Getting Min and Max for Energy Column...
Got min and max for PI: 0 1023
Got the minimum time resolution of the read data: 0.62500E-01
Number of files read in: 4
******************** Observation Catalogue ********************
Data Directory is: /data/data17/seq_proc/50006000.007/
HK Directory is: /data/data17/seq_proc/50006000.007/
!xsel:ASCA-GIS3-PH > set phaname PI
!xsel:ASCA-GIS3-PH > filter region ad50006000g325670_1.reg
!xsel:ASCA-GIS3-PH > filter region GIS3_REGION256_OFF.4
!xsel:ASCA-GIS3-PH > extract spectrum
!xsel:ASCA-GIS3-PH > save spectrum ad50006000g310170_1.pi group=yes
Wrote spectrum to ad50006000g310170_1.pi
!xsel:ASCA-GIS3-PH > exit save_session=no
-> Correcting ad50006000g310170_1.pi for dead time... read all the files from deadlist.tmp-> Grouping ad50006000g310170_1.pi to 40 counts/bin
------------------------- MANDATORY KEYWORDS/VALUES ------------------------- -------------------------------------------------------------------- -------------------------------------------------------------------- EXTNAME - SPECTRUM Name of this BINTABLE TELESCOP - ASCA Mission/Satellite name INSTRUME - GIS3 Instrument/Detector FILTER - Instrument filter in use EXPOSURE - 37698. Integration time (in secs) of PHA data AREASCAL - 1.0000 Area scaling factor BACKSCAL - 5.44586E-02 Background scaling factor BACKFILE - NONE Associated background file CORRSCAL - 1.0000 Correlation scaling factor CORRFILE - none Associated correlation file RESPFILE - NONE Associated redistribution matrix file ANCRFILE - none Associated ancillary response file XFLT0001 - none XSPEC selection filter POISSERR - TRUE Whether Poissonian errors apply CHANTYPE - PI Whether channels have been corrected TLMIN1 - 0 First legal Detector channel DETCHANS - 1024 No. of legal detector channels NCHAN - 1024 No. of detector channels in dataset PHAVERSN - 1.1.0 OGIP FITS version number STAT_ERR - FALSE Statistical Error SYS_ERR - TRUE Fractional Systematic Error QUALITY - TRUE Quality Flag GROUPING - TRUE Grouping Flag -------------------------------------------------------------------- -------------------------------------------------------------------- ... ... -------- ... GROUPING ... -------- ... --------------------------------------------- ... Channel Grouping (Channel-Channel) : ... 0 - 22 are grouped by a factor 23 ... 23 - 28 are grouped by a factor 3 ... 29 - 44 are grouped by a factor 4 ... 45 - 47 are grouped by a factor 3 ... 48 - 57 are grouped by a factor 5 ... 58 - 60 are grouped by a factor 3 ... 61 - 64 are grouped by a factor 4 ... 65 - 70 are grouped by a factor 3 ... 71 - 94 are grouped by a factor 2 ... 95 - 95 are single channels ... 96 - 99 are grouped by a factor 2 ... 100 - 100 are single channels ... 101 - 104 are grouped by a factor 2 ... 105 - 107 are single channels ... 108 - 109 are grouped by a factor 2 ... 110 - 120 are single channels ... 121 - 122 are grouped by a factor 2 ... 123 - 165 are single channels ... 166 - 167 are grouped by a factor 2 ... 168 - 169 are single channels ... 170 - 171 are grouped by a factor 2 ... 172 - 174 are single channels ... 175 - 176 are grouped by a factor 2 ... 177 - 178 are single channels ... 179 - 180 are grouped by a factor 2 ... 181 - 181 are single channels ... 182 - 189 are grouped by a factor 2 ... 190 - 190 are single channels ... 191 - 210 are grouped by a factor 2 ... 211 - 216 are grouped by a factor 3 ... 217 - 218 are grouped by a factor 2 ... 219 - 221 are grouped by a factor 3 ... 222 - 229 are grouped by a factor 2 ... 230 - 232 are grouped by a factor 3 ... 233 - 236 are grouped by a factor 2 ... 237 - 251 are grouped by a factor 3 ... 252 - 253 are grouped by a factor 2 ... 254 - 265 are grouped by a factor 3 ... 266 - 267 are grouped by a factor 2 ... 268 - 294 are grouped by a factor 3 ... 295 - 298 are grouped by a factor 4 ... 299 - 307 are grouped by a factor 3 ... 308 - 311 are grouped by a factor 4 ... 312 - 317 are grouped by a factor 3 ... 318 - 329 are grouped by a factor 4 ... 330 - 334 are grouped by a factor 5 ... 335 - 342 are grouped by a factor 4 ... 343 - 347 are grouped by a factor 5 ... 348 - 350 are grouped by a factor 3 ... 351 - 360 are grouped by a factor 5 ... 361 - 367 are grouped by a factor 7 ... 368 - 382 are grouped by a factor 5 ... 383 - 388 are grouped by a factor 6 ... 389 - 393 are grouped by a factor 5 ... 394 - 399 are grouped by a factor 6 ... 400 - 409 are grouped by a factor 5 ... 410 - 417 are grouped by a factor 8 ... 418 - 424 are grouped by a factor 7 ... 425 - 429 are grouped by a factor 5 ... 430 - 443 are grouped by a factor 7 ... 444 - 451 are grouped by a factor 8 ... 452 - 460 are grouped by a factor 9 ... 461 - 468 are grouped by a factor 8 ... 469 - 475 are grouped by a factor 7 ... 476 - 486 are grouped by a factor 11 ... 487 - 506 are grouped by a factor 10 ... 507 - 517 are grouped by a factor 11 ... 518 - 541 are grouped by a factor 12 ... 542 - 554 are grouped by a factor 13 ... 555 - 569 are grouped by a factor 15 ... 570 - 586 are grouped by a factor 17 ... 587 - 612 are grouped by a factor 26 ... 613 - 635 are grouped by a factor 23 ... 636 - 691 are grouped by a factor 28 ... 692 - 721 are grouped by a factor 30 ... 722 - 759 are grouped by a factor 38 ... 760 - 820 are grouped by a factor 61 ... 821 - 898 are grouped by a factor 78 ... 899 - 1023 of undefined grouping (Channel quality=bad) ... --------------------------------------------- ... ...... exiting, changes written to file : ad50006000g310170_1.pi ** grppha 2.6.0 completed successfully-> Fetching gis3v4_0.rmf
ASCAARF vers 2.72 14 Mar 1997.
Input WMAP array has size 67 by 67 bins
expanded to 128 by 128 bins
First WMAP bin is at detector pixel 52 88
1 detector pixels per WMAP bin
WMAP bin size is 0.25000 mm
0.24555 arcmin
Selected region size is 215.24 arcmin^2
Optical axis is detector pixel 119.36 134.44
201 energies from RMF file
Effective area fudge applied
Arf filter applied
Total counts in region = 1.00260E+04
Weighted mean angle from optical axis = 5.467 arcmin
-> Plotting ad50006000g210170_1_pi.ps from ad50006000g210170_1.pi
XSPEC 9.01 16:27:43 18-Mar-98
Plot device not set, use "cpd" to set it
Type "help" or "?" for further information
!XSPEC> data ad50006000g210170_1.pi
Net count rate (cts/s) for file 1 0.2223 +/- 2.4389E-03
1 data set is in use
!XSPEC> setplot energy
!XSPEC> ignore bad
!XSPEC> iplot
!PLT> log y on
!PLT> rescale y
!PLT> hard /ps
!PLT> quit
!XSPEC> exit
!Do you really want to exit (y) y
XSPEC: quit
-> Plotting ad50006000g310170_1_pi.ps from ad50006000g310170_1.pi
XSPEC 9.01 16:28:14 18-Mar-98
Plot device not set, use "cpd" to set it
Type "help" or "?" for further information
!XSPEC> data ad50006000g310170_1.pi
Net count rate (cts/s) for file 1 0.2660 +/- 2.6692E-03
1 data set is in use
!XSPEC> setplot energy
!XSPEC> ignore bad
!XSPEC> iplot
!PLT> log y on
!PLT> rescale y
!PLT> hard /ps
!PLT> quit
!XSPEC> exit
!Do you really want to exit (y) y
XSPEC: quit
-> Plotting ad50006000s010102_1_pi.ps from ad50006000s010102_1.pi
XSPEC 9.01 16:28:43 18-Mar-98
Plot device not set, use "cpd" to set it
Type "help" or "?" for further information
!XSPEC> data ad50006000s010102_1.pi
Net count rate (cts/s) for file 1 0.3992 +/- 3.4480E-03
1 data set is in use
!XSPEC> setplot energy
!XSPEC> ignore bad
!XSPEC> iplot
!PLT> log y on
!PLT> rescale y
!PLT> hard /ps
!PLT> quit
!XSPEC> exit
!Do you really want to exit (y) y
XSPEC: quit
-> Plotting ad50006000s010202_1_pi.ps from ad50006000s010202_1.pi
XSPEC 9.01 16:29:12 18-Mar-98
Plot device not set, use "cpd" to set it
Type "help" or "?" for further information
!XSPEC> data ad50006000s010202_1.pi
Net count rate (cts/s) for file 1 0.3217 +/- 1.3275E-02
1 data set is in use
!XSPEC> setplot energy
!XSPEC> ignore bad
!XSPEC> iplot
!PLT> log y on
!PLT> rescale y
!PLT> hard /ps
!PLT> quit
!XSPEC> exit
!Do you really want to exit (y) y
XSPEC: quit
-> Plotting ad50006000s010312_1_pi.ps from ad50006000s010312_1.pi
XSPEC 9.01 16:29:41 18-Mar-98
Plot device not set, use "cpd" to set it
Type "help" or "?" for further information
!XSPEC> data ad50006000s010312_1.pi
Net count rate (cts/s) for file 1 0.4138 +/- 4.9374E-03
1 data set is in use
!XSPEC> setplot energy
!XSPEC> ignore bad
!XSPEC> iplot
!PLT> log y on
!PLT> rescale y
!PLT> hard /ps
!PLT> quit
!XSPEC> exit
!Do you really want to exit (y) y
XSPEC: quit
-> Plotting ad50006000s010412_1_pi.ps from ad50006000s010412_1.pi
XSPEC 9.01 16:30:17 18-Mar-98
Plot device not set, use "cpd" to set it
Type "help" or "?" for further information
!XSPEC> data ad50006000s010412_1.pi
Net count rate (cts/s) for file 1 0.3310 +/- 1.3295E-02
1 data set is in use
!XSPEC> setplot energy
!XSPEC> ignore bad
!XSPEC> iplot
!PLT> log y on
!PLT> rescale y
!PLT> hard /ps
!PLT> quit
!XSPEC> exit
!Do you really want to exit (y) y
XSPEC: quit
-> Plotting ad50006000s110102_1_pi.ps from ad50006000s110102_1.pi
XSPEC 9.01 16:30:52 18-Mar-98
Plot device not set, use "cpd" to set it
Type "help" or "?" for further information
!XSPEC> data ad50006000s110102_1.pi
Net count rate (cts/s) for file 1 0.4449 +/- 3.5338E-03
1 data set is in use
!XSPEC> setplot energy
!XSPEC> ignore bad
!XSPEC> iplot
!PLT> log y on
!PLT> rescale y
!PLT> hard /ps
!PLT> quit
!XSPEC> exit
!Do you really want to exit (y) y
XSPEC: quit
-> Plotting ad50006000s110212_1_pi.ps from ad50006000s110212_1.pi
XSPEC 9.01 16:31:23 18-Mar-98
Plot device not set, use "cpd" to set it
Type "help" or "?" for further information
!XSPEC> data ad50006000s110212_1.pi
Net count rate (cts/s) for file 1 0.4498 +/- 4.8790E-03
1 data set is in use
!XSPEC> setplot energy
!XSPEC> ignore bad
!XSPEC> iplot
!PLT> log y on
!PLT> rescale y
!PLT> hard /ps
!PLT> quit
!XSPEC> exit
!Do you really want to exit (y) y
XSPEC: quit
** XSELECT V1.3 **
!> Enter session name >[xsel] xsel
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS S0CCDPOW
1 W50 EAST BRIGHT HIGH 28/04/93 03:44:28 0.16E+05 10231 1111
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS S0CCDPOW
1 W50 EAST BRIGHT HIGH 28/04/93 03:44:28 0.16E+05 10231 1111
2 W50 EAST BRIGHT MEDIUM 27/04/93 23:50:32 0.11E+05 7322 1111
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS S0CCDPOW
1 W50 EAST BRIGHT HIGH 28/04/93 03:44:28 0.16E+05 10231 1111
2 W50 EAST BRIGHT MEDIUM 27/04/93 23:50:32 0.11E+05 7322 1111
3 W50 EAST BRIGHT HIGH 28/04/93 14:34:00 0.19E+04 1341 1011
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS S0CCDPOW
1 W50 EAST BRIGHT HIGH 28/04/93 03:44:28 0.16E+05 10231 1111
2 W50 EAST BRIGHT MEDIUM 27/04/93 23:50:32 0.11E+05 7322 1111
3 W50 EAST BRIGHT HIGH 28/04/93 14:34:00 0.19E+04 1341 1011
4 W50 EAST BRIGHT MEDIUM 28/04/93 19:50:16 0.55E+04 3663 1111
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS S0CCDPOW
1 W50 EAST BRIGHT HIGH 28/04/93 03:44:28 0.16E+05 10231 1111
2 W50 EAST BRIGHT MEDIUM 27/04/93 23:50:32 0.11E+05 7322 1111
3 W50 EAST BRIGHT HIGH 28/04/93 14:34:00 0.19E+04 1341 1011
4 W50 EAST BRIGHT MEDIUM 28/04/93 19:50:16 0.55E+04 3663 1111
5 W50 EAST BRIGHT HIGH 28/04/93 22:52:12 0.15E+04 976 1111
EXTRACTOR vers 2.0 11 Apr 1997.
Doing file: /data/data17/seq_proc/50006000.007/ad50006000s000102h.evt
Total Good Bad: Region Time Phase Cut
10231 6357 3874 0 0 0
Writing events file
6357 events written to the output file
Doing file: /data/data17/seq_proc/50006000.007/ad50006000s000202m.evt
Total Good Bad: Region Time Phase Cut
7322 4449 2873 0 0 0
Writing events file
10806 events written to the output file
Doing file: /data/data17/seq_proc/50006000.007/ad50006000s000302h.evt
Total Good Bad: Region Time Phase Cut
1341 835 506 0 0 0
Writing events file
11641 events written to the output file
Doing file: /data/data17/seq_proc/50006000.007/ad50006000s000502m.evt
Total Good Bad: Region Time Phase Cut
3663 2223 1440 0 0 0
Writing events file
13864 events written to the output file
Doing file: /data/data17/seq_proc/50006000.007/ad50006000s000602h.evt
Total Good Bad: Region Time Phase Cut
976 626 350 0 0 0
Writing events file
14490 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
23533 14490 9043 0 0 0
in 35544.80 seconds
Command not found; type ? for a command listing
!xsel:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!xsel:ASCA > set datadir .
Setting data directory to /data/data17/seq_proc/50006000.007/
Setting mkf directory to /data/data17/seq_proc/50006000.007/
!xsel:ASCA > read events ad50006000s000102h.evt
Got new instrument: SIS0
Setting: IMAGE binning = 4
WMAP binning = 8
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 2047
Got the minimum time resolution of the read data: 16.000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data17/seq_proc/50006000.007/
HK Directory is: /data/data17/seq_proc/50006000.007/
!xsel:ASCA-SIS0-BRIGHT > read events ad50006000s000202m.evt
Getting Min and Max for Energy Column...
Got min and max for PI: 0 2047
Got the minimum time resolution of the read data: 16.000
Number of files read in: 2
******************** Observation Catalogue ********************
Data Directory is: /data/data17/seq_proc/50006000.007/
HK Directory is: /data/data17/seq_proc/50006000.007/
!xsel:ASCA-SIS0-BRIGHT > read events ad50006000s000302h.evt
Getting Min and Max for Energy Column...
Got min and max for PI: 0 2047
Got the minimum time resolution of the read data: 16.000
Number of files read in: 3
******************** Observation Catalogue ********************
Data Directory is: /data/data17/seq_proc/50006000.007/
HK Directory is: /data/data17/seq_proc/50006000.007/
!xsel:ASCA-SIS0-BRIGHT > read events ad50006000s000502m.evt
Getting Min and Max for Energy Column...
Got min and max for PI: 0 2047
Got the minimum time resolution of the read data: 16.000
Number of files read in: 4
******************** Observation Catalogue ********************
Data Directory is: /data/data17/seq_proc/50006000.007/
HK Directory is: /data/data17/seq_proc/50006000.007/
!xsel:ASCA-SIS0-BRIGHT > read events ad50006000s000602h.evt
Getting Min and Max for Energy Column...
Got min and max for PI: 0 2047
Got the minimum time resolution of the read data: 16.000
Number of files read in: 5
******************** Observation Catalogue ********************
Data Directory is: /data/data17/seq_proc/50006000.007/
HK Directory is: /data/data17/seq_proc/50006000.007/
!xsel:ASCA-SIS0-BRIGHT > filter region ad50006000s032002_1.reg
!xsel:ASCA-SIS0-BRIGHT > extract events
!xsel:ASCA-SIS0-BRIGHT > save events outfile=events.tmp use_events=yes
Wrote events list to file events.tmp
Changing Data directory from:
/data/data17/seq_proc/50006000.007/
to the current working directory.
!xsel:ASCA-SIS0-BRIGHT > exit save_session=no
-> Extracting ad50006000s000002_1.lc with binsize 122.652865305673
** XSELECT V1.3 **
!> Enter session name >[xsel] xsel
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS S0CCDPOW
1 W50 EAST BRIGHT HIGH 27/04/93 23:50:32 0.36E+05 14490 1111
EXTRACTOR vers 2.0 11 Apr 1997.
Doing file: /data/data17/seq_proc/50006000.007/events.tmp
Total Good Bad: Region Time Phase Cut
14490 14490 0 0 0 0
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
14490 14490 0 0 0 0
in 35544.80 seconds
Fits light curve has 14490 counts for 0.4077 counts/sec
Command not found; type ? for a command listing
!xsel:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!xsel:ASCA > set datadir .
Setting data directory to /data/data17/seq_proc/50006000.007/
Setting mkf directory to /data/data17/seq_proc/50006000.007/
!xsel:ASCA > read events events.tmp
Got new instrument: SIS0
Setting: IMAGE binning = 4
WMAP binning = 8
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 2047
Got the minimum time resolution of the read data: 16.000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data17/seq_proc/50006000.007/
HK Directory is: /data/data17/seq_proc/50006000.007/
!xsel:ASCA-SIS0-BRIGHT > set binsize 122.652865305673
!xsel:ASCA-SIS0-BRIGHT > extract curve exposure=0.5
!xsel:ASCA-SIS0-BRIGHT > save curve ad50006000s000002_1.lc
Wrote FITS light curve to file ad50006000s000002_1.lc
!xsel:ASCA-SIS0-BRIGHT > exit save_session=no
-> Plotting light curve ad50006000s000002_1_lc.ps
Type "help" for information
[1]xronos> Current User Interface is ; command driven
[2]xronos> Enter up to 50 input filenames and options for series 1 (or rtn)
Ser. A filename 1 +options[.rbf]=> ad50006000s000002_1.lc
Selected FITS extensions: 1 - RATE TABLE;
Source ............ W50 EAST LOBE (P Start Time (d) .... 9105 00:06:48.723
FITS Extension .... 1 - `RATE ` Stop Time (d) ..... 9105 23:23:44.499
No. of Rows ....... 293 Bin Time (s) ...... 122.7
Right Ascension ... 2.8844E+02 Internal time sys.. Converted to TJD
Declination ....... 4.9767E+00 Experiment ........ ASCA SIS0
Corrections applied: Vignetting - No ; Deadtime - No ; Bkgd - No ; Clock - No
Selected Columns: 1 - Time; 2 - Y-axis; 3 - Y-error;
File contains binned data.
Ser. A filename 2 +options[.rbf]=>
Enter up to 50 input filenames and options for series 2 (or rtn)
Ser. B filename 1 +options[.rbf]=>
Enter up to 50 input filenames and options for series 3 (or rtn)
Ser. C filename 1 +options[.rbf]=>
[3]xronos>
Maximum of 1 Intvs. with 512 Newbins of 163.895 (s)
Intv 1 Start 9105 0: 8:10
Ser.1 Avg 0.4060 Chisq 386.7 Var 0.5147E-02 Newbs. 229
Min 0.2283 Max 0.7042 expVar 0.3094E-02 Bins 293
Results from Statistical Analysis
Newbin Integration Time (s).. 163.89
Interval Duration (s)........ 83586.
No. of Newbins .............. 229
Average (c/s) ............... 0.40599 +/- 0.37E-02
Standard Deviation (c/s)..... 0.71741E-01
Minimum (c/s)................ 0.22829
Maximum (c/s)................ 0.70419
Variance ((c/s)**2).......... 0.51467E-02 +/- 0.48E-03
Expected Variance ((c/s)**2). 0.30938E-02 +/- 0.29E-03
Third Moment ((c/s)**3)...... 0.30403E-03
Average Deviation (c/s)...... 0.55605E-01
Skewness..................... 0.82342 +/- 0.16
Kurtosis..................... 1.7525 +/- 0.32
RMS fractional variation..... 0.11160 +/- 0.13E-01
Chi-Square................... 386.72 dof 228
Chi-Square Prob of constancy. 0.25703E-09 (0 means < 1.e-38)
Kolm.-Smir. Prob of constancy 0.14244E-01 (0 means < 1.e-38)
[4]xronos> [5]xronos>
Maximum of 1 Intvs. with 512 Newbins of 163.895 (s)
Intv 1 Start 9105 0: 8:10
Ser.1 Avg 0.4060 Chisq 386.7 Var 0.5147E-02 Newbs. 229
Min 0.2283 Max 0.7042 expVar 0.3094E-02 Bins 293
Light curve ready !
Frme 1 Written to output file : xronos.qlc1
PLT> PLT> PLT> [6]xronos>
-> TIMEDEL=1.6000000000E+01 for ad50006000s100102h.evt
** XSELECT V1.3 **
!> Enter session name >[xsel] xsel
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS S1CCDPOW
1 W50 EAST BRIGHT HIGH 28/04/93 03:44:28 0.18E+05 12214 1111
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS S1CCDPOW
1 W50 EAST BRIGHT HIGH 28/04/93 03:44:28 0.18E+05 12214 1111
2 W50 EAST BRIGHT MEDIUM 27/04/93 23:50:32 0.11E+05 7884 1111
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS S1CCDPOW
1 W50 EAST BRIGHT HIGH 28/04/93 03:44:28 0.18E+05 12214 1111
2 W50 EAST BRIGHT MEDIUM 27/04/93 23:50:32 0.11E+05 7884 1111
3 W50 EAST BRIGHT MEDIUM 28/04/93 19:50:16 0.56E+04 4002 1111
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS S1CCDPOW
1 W50 EAST BRIGHT HIGH 28/04/93 03:44:28 0.18E+05 12214 1111
2 W50 EAST BRIGHT MEDIUM 27/04/93 23:50:32 0.11E+05 7884 1111
3 W50 EAST BRIGHT MEDIUM 28/04/93 19:50:16 0.56E+04 4002 1111
4 W50 EAST BRIGHT HIGH 28/04/93 22:52:12 0.14E+04 1095 1111
EXTRACTOR vers 2.0 11 Apr 1997.
Doing file: /data/data17/seq_proc/50006000.007/ad50006000s100102h.evt
Total Good Bad: Region Time Phase Cut
12214 7764 4450 0 0 0
Writing events file
7764 events written to the output file
Doing file: /data/data17/seq_proc/50006000.007/ad50006000s100202m.evt
Total Good Bad: Region Time Phase Cut
7884 5051 2833 0 0 0
Writing events file
12815 events written to the output file
Doing file: /data/data17/seq_proc/50006000.007/ad50006000s100502m.evt
Total Good Bad: Region Time Phase Cut
4002 2526 1476 0 0 0
Writing events file
15341 events written to the output file
Doing file: /data/data17/seq_proc/50006000.007/ad50006000s100602h.evt
Total Good Bad: Region Time Phase Cut
1095 733 362 0 0 0
Writing events file
16074 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
25195 16074 9121 0 0 0
in 35648.30 seconds
Command not found; type ? for a command listing
!xsel:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!xsel:ASCA > set datadir .
Setting data directory to /data/data17/seq_proc/50006000.007/
Setting mkf directory to /data/data17/seq_proc/50006000.007/
!xsel:ASCA > read events ad50006000s100102h.evt
Got new instrument: SIS1
Setting: IMAGE binning = 4
WMAP binning = 8
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 2047
Got the minimum time resolution of the read data: 16.000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data17/seq_proc/50006000.007/
HK Directory is: /data/data17/seq_proc/50006000.007/
!xsel:ASCA-SIS1-BRIGHT > read events ad50006000s100202m.evt
Getting Min and Max for Energy Column...
Got min and max for PI: 0 2047
Got the minimum time resolution of the read data: 16.000
Number of files read in: 2
******************** Observation Catalogue ********************
Data Directory is: /data/data17/seq_proc/50006000.007/
HK Directory is: /data/data17/seq_proc/50006000.007/
!xsel:ASCA-SIS1-BRIGHT > read events ad50006000s100502m.evt
Getting Min and Max for Energy Column...
Got min and max for PI: 0 2047
Got the minimum time resolution of the read data: 16.000
Number of files read in: 3
******************** Observation Catalogue ********************
Data Directory is: /data/data17/seq_proc/50006000.007/
HK Directory is: /data/data17/seq_proc/50006000.007/
!xsel:ASCA-SIS1-BRIGHT > read events ad50006000s100602h.evt
Getting Min and Max for Energy Column...
Got min and max for PI: 0 2047
Got the minimum time resolution of the read data: 16.000
Number of files read in: 4
******************** Observation Catalogue ********************
Data Directory is: /data/data17/seq_proc/50006000.007/
HK Directory is: /data/data17/seq_proc/50006000.007/
!xsel:ASCA-SIS1-BRIGHT > filter region ad50006000s132002_1.reg
!xsel:ASCA-SIS1-BRIGHT > extract events
!xsel:ASCA-SIS1-BRIGHT > save events outfile=events.tmp use_events=yes
Wrote events list to file events.tmp
Changing Data directory from:
/data/data17/seq_proc/50006000.007/
to the current working directory.
!xsel:ASCA-SIS1-BRIGHT > exit save_session=no
-> Extracting ad50006000s100002_1.lc with binsize 110.888065204847
** XSELECT V1.3 **
!> Enter session name >[xsel] xsel
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS S1CCDPOW
1 W50 EAST BRIGHT HIGH 27/04/93 23:50:32 0.36E+05 16074 1111
EXTRACTOR vers 2.0 11 Apr 1997.
Doing file: /data/data17/seq_proc/50006000.007/events.tmp
Total Good Bad: Region Time Phase Cut
16074 16074 0 0 0 0
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
16074 16074 0 0 0 0
in 35648.30 seconds
Fits light curve has 16074 counts for 0.4509 counts/sec
Command not found; type ? for a command listing
!xsel:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!xsel:ASCA > set datadir .
Setting data directory to /data/data17/seq_proc/50006000.007/
Setting mkf directory to /data/data17/seq_proc/50006000.007/
!xsel:ASCA > read events events.tmp
Got new instrument: SIS1
Setting: IMAGE binning = 4
WMAP binning = 8
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 2047
Got the minimum time resolution of the read data: 16.000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data17/seq_proc/50006000.007/
HK Directory is: /data/data17/seq_proc/50006000.007/
!xsel:ASCA-SIS1-BRIGHT > set binsize 110.888065204847
!xsel:ASCA-SIS1-BRIGHT > extract curve exposure=0.5
!xsel:ASCA-SIS1-BRIGHT > save curve ad50006000s100002_1.lc
Wrote FITS light curve to file ad50006000s100002_1.lc
!xsel:ASCA-SIS1-BRIGHT > exit save_session=no
-> Plotting light curve ad50006000s100002_1_lc.ps
Type "help" for information
[1]xronos> Current User Interface is ; command driven
[2]xronos> Enter up to 50 input filenames and options for series 1 (or rtn)
Ser. A filename 1 +options[.rbf]=> ad50006000s100002_1.lc
Selected FITS extensions: 1 - RATE TABLE;
Source ............ W50 EAST LOBE (P Start Time (d) .... 9105 00:06:48.723
FITS Extension .... 1 - `RATE ` Stop Time (d) ..... 9105 23:23:44.499
No. of Rows ....... 329 Bin Time (s) ...... 110.9
Right Ascension ... 2.8844E+02 Internal time sys.. Converted to TJD
Declination ....... 4.9767E+00 Experiment ........ ASCA SIS1
Corrections applied: Vignetting - No ; Deadtime - No ; Bkgd - No ; Clock - No
Selected Columns: 1 - Time; 2 - Y-axis; 3 - Y-error;
File contains binned data.
Ser. A filename 2 +options[.rbf]=>
Enter up to 50 input filenames and options for series 2 (or rtn)
Ser. B filename 1 +options[.rbf]=>
Enter up to 50 input filenames and options for series 3 (or rtn)
Ser. C filename 1 +options[.rbf]=>
[3]xronos>
Maximum of 1 Intvs. with 512 Newbins of 163.895 (s)
Intv 1 Start 9105 0: 8:10
Ser.1 Avg 0.4530 Chisq 449.9 Var 0.6092E-02 Newbs. 232
Min 0.2615 Max 1.080 expVar 0.3571E-02 Bins 329
Results from Statistical Analysis
Newbin Integration Time (s).. 163.89
Interval Duration (s)........ 83750.
No. of Newbins .............. 232
Average (c/s) ............... 0.45298 +/- 0.39E-02
Standard Deviation (c/s)..... 0.78050E-01
Minimum (c/s)................ 0.26153
Maximum (c/s)................ 1.0804
Variance ((c/s)**2).......... 0.60918E-02 +/- 0.57E-03
Expected Variance ((c/s)**2). 0.35715E-02 +/- 0.33E-03
Third Moment ((c/s)**3)...... 0.11949E-02
Average Deviation (c/s)...... 0.53910E-01
Skewness..................... 2.5131 +/- 0.16
Kurtosis..................... 17.825 +/- 0.32
RMS fractional variation..... 0.11083 +/- 0.12E-01
Chi-Square................... 449.86 dof 231
Chi-Square Prob of constancy. 0.31167E-15 (0 means < 1.e-38)
Kolm.-Smir. Prob of constancy 0.54665E-03 (0 means < 1.e-38)
[4]xronos> [5]xronos>
Maximum of 1 Intvs. with 512 Newbins of 163.895 (s)
Intv 1 Start 9105 0: 8:10
Ser.1 Avg 0.4530 Chisq 449.9 Var 0.6092E-02 Newbs. 232
Min 0.2615 Max 1.080 expVar 0.3571E-02 Bins 329
Light curve ready !
Frme 1 Written to output file : xronos.qlc1
PLT> PLT> PLT> [6]xronos>
-> TIMEDEL=5.0000000000E-01 for ad50006000g200170m.evt
** XSELECT V1.3 **
!> Enter session name >[xsel] xsel
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS PHA_BINS
1 W50 EAST PH MEDIUM 27/04/93 23:50:48 0.12E+05 7555 1024
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS PHA_BINS
1 W50 EAST PH MEDIUM 27/04/93 23:50:48 0.12E+05 7555 1024
2 W50 EAST PH HIGH 28/04/93 03:44:46 0.18E+05 11655 1024
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS PHA_BINS
1 W50 EAST PH MEDIUM 27/04/93 23:50:48 0.12E+05 7555 1024
2 W50 EAST PH HIGH 28/04/93 03:44:46 0.18E+05 11655 1024
3 W50 EAST PH MEDIUM 28/04/93 19:50:32 0.68E+04 4255 1024
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS PHA_BINS
1 W50 EAST PH MEDIUM 27/04/93 23:50:48 0.12E+05 7555 1024
2 W50 EAST PH HIGH 28/04/93 03:44:46 0.18E+05 11655 1024
3 W50 EAST PH MEDIUM 28/04/93 19:50:32 0.68E+04 4255 1024
4 W50 EAST PH HIGH 28/04/93 22:52:30 0.15E+04 1004 1024
EXTRACTOR vers 2.0 11 Apr 1997.
Doing file: /data/data17/seq_proc/50006000.007/ad50006000g200170m.evt
Total Good Bad: Region Time Phase Cut
7555 2557 4998 0 0 0
Writing events file
2557 events written to the output file
Doing file: /data/data17/seq_proc/50006000.007/ad50006000g200270h.evt
Total Good Bad: Region Time Phase Cut
11655 4030 7625 0 0 0
Writing events file
6587 events written to the output file
Doing file: /data/data17/seq_proc/50006000.007/ad50006000g200470m.evt
Total Good Bad: Region Time Phase Cut
4255 1431 2824 0 0 0
Writing events file
8018 events written to the output file
Doing file: /data/data17/seq_proc/50006000.007/ad50006000g200570h.evt
Total Good Bad: Region Time Phase Cut
1004 360 644 0 0 0
Writing events file
8378 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
24469 8378 16091 0 0 0
in 37693.54 seconds
Command not found; type ? for a command listing
!xsel:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!xsel:ASCA > set datadir .
Setting data directory to /data/data17/seq_proc/50006000.007/
Setting mkf directory to /data/data17/seq_proc/50006000.007/
!xsel:ASCA > read events ad50006000g200170m.evt
Got new instrument: GIS2
Setting: IMAGE binning = 1
WMAP binning = 1
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 1023
Got the minimum time resolution of the read data: 0.50000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data17/seq_proc/50006000.007/
HK Directory is: /data/data17/seq_proc/50006000.007/
!xsel:ASCA-GIS2-PH > read events ad50006000g200270h.evt
Getting Min and Max for Energy Column...
Got min and max for PI: 0 1023
Got the minimum time resolution of the read data: 0.62500E-01
Number of files read in: 2
******************** Observation Catalogue ********************
Data Directory is: /data/data17/seq_proc/50006000.007/
HK Directory is: /data/data17/seq_proc/50006000.007/
!xsel:ASCA-GIS2-PH > read events ad50006000g200470m.evt
Getting Min and Max for Energy Column...
Got min and max for PI: 0 1023
Got the minimum time resolution of the read data: 0.50000
Number of files read in: 3
******************** Observation Catalogue ********************
Data Directory is: /data/data17/seq_proc/50006000.007/
HK Directory is: /data/data17/seq_proc/50006000.007/
!xsel:ASCA-GIS2-PH > read events ad50006000g200570h.evt
Getting Min and Max for Energy Column...
Got min and max for PI: 0 1023
Got the minimum time resolution of the read data: 0.62500E-01
Number of files read in: 4
******************** Observation Catalogue ********************
Data Directory is: /data/data17/seq_proc/50006000.007/
HK Directory is: /data/data17/seq_proc/50006000.007/
!xsel:ASCA-GIS2-PH > filter region ad50006000g225670_1.reg
!xsel:ASCA-GIS2-PH > extract events
!xsel:ASCA-GIS2-PH > save events outfile=events.tmp use_events=yes
Wrote events list to file events.tmp
Changing Data directory from:
/data/data17/seq_proc/50006000.007/
to the current working directory.
!xsel:ASCA-GIS2-PH > exit save_session=no
-> Extracting ad50006000g200070_1.lc with binsize 224.955470282836
** XSELECT V1.3 **
!> Enter session name >[xsel] xsel
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS PHA_BINS
1 W50 EAST PH MEDIUM 27/04/93 23:50:48 0.38E+05 8378 1024
EXTRACTOR vers 2.0 11 Apr 1997.
Doing file: /data/data17/seq_proc/50006000.007/events.tmp
Total Good Bad: Region Time Phase Cut
8378 8378 0 0 0 0
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
8378 8378 0 0 0 0
in 37693.54 seconds
Fits light curve has 8378 counts for 0.2223 counts/sec
Command not found; type ? for a command listing
!xsel:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!xsel:ASCA > set datadir .
Setting data directory to /data/data17/seq_proc/50006000.007/
Setting mkf directory to /data/data17/seq_proc/50006000.007/
!xsel:ASCA > read events events.tmp
Got new instrument: GIS2
Setting: IMAGE binning = 1
WMAP binning = 1
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 1023
Got the minimum time resolution of the read data: 0.50000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data17/seq_proc/50006000.007/
HK Directory is: /data/data17/seq_proc/50006000.007/
!xsel:ASCA-GIS2-PH > set binsize 224.955470282836
!xsel:ASCA-GIS2-PH > extract curve exposure=0.5
!xsel:ASCA-GIS2-PH > save curve ad50006000g200070_1.lc
Wrote FITS light curve to file ad50006000g200070_1.lc
!xsel:ASCA-GIS2-PH > exit save_session=no
-> Plotting light curve ad50006000g200070_1_lc.ps
Type "help" for information
[1]xronos> Current User Interface is ; command driven
[2]xronos> Enter up to 50 input filenames and options for series 1 (or rtn)
Ser. A filename 1 +options[.rbf]=> ad50006000g200070_1.lc
Selected FITS extensions: 1 - RATE TABLE;
Source ............ W50 EAST LOBE (P Start Time (d) .... 9105 00:05:44.723
FITS Extension .... 1 - `RATE ` Stop Time (d) ..... 9105 23:27:28.499
No. of Rows ....... 167 Bin Time (s) ...... 225.0
Right Ascension ... 2.8844E+02 Internal time sys.. Converted to TJD
Declination ....... 4.9767E+00 Experiment ........ ASCA GIS2
Corrections applied: Vignetting - No ; Deadtime - No ; Bkgd - No ; Clock - No
Selected Columns: 1 - Time; 2 - Y-axis; 3 - Y-error;
File contains binned data.
Ser. A filename 2 +options[.rbf]=>
Enter up to 50 input filenames and options for series 2 (or rtn)
Ser. B filename 1 +options[.rbf]=>
Enter up to 50 input filenames and options for series 3 (or rtn)
Ser. C filename 1 +options[.rbf]=>
[3]xronos>
Maximum of 1 Intvs. with 374 Newbins of 224.955 (s)
Intv 1 Start 9105 0: 7:37
Ser.1 Avg 0.2229 Chisq 172.9 Var 0.1109E-02 Newbs. 167
Min 0.1473 Max 0.3334 expVar 0.1072E-02 Bins 167
Results from Statistical Analysis
Newbin Integration Time (s).. 224.96
Interval Duration (s)........ 83908.
No. of Newbins .............. 167
Average (c/s) ............... 0.22295 +/- 0.25E-02
Standard Deviation (c/s)..... 0.33308E-01
Minimum (c/s)................ 0.14734
Maximum (c/s)................ 0.33340
Variance ((c/s)**2).......... 0.11094E-02 +/- 0.12E-03
Expected Variance ((c/s)**2). 0.10716E-02 +/- 0.12E-03
Third Moment ((c/s)**3)...... 0.10650E-04
Average Deviation (c/s)...... 0.26983E-01
Skewness..................... 0.28820 +/- 0.19
Kurtosis..................... 0.16020E-01 +/- 0.38
RMS fractional variation....< 0.83900E-01 (3 sigma)
Chi-Square................... 172.89 dof 166
Chi-Square Prob of constancy. 0.34114 (0 means < 1.e-38)
Kolm.-Smir. Prob of constancy 0.17213 (0 means < 1.e-38)
[4]xronos> [5]xronos>
Maximum of 1 Intvs. with 374 Newbins of 224.955 (s)
Intv 1 Start 9105 0: 7:37
Ser.1 Avg 0.2229 Chisq 172.9 Var 0.1109E-02 Newbs. 167
Min 0.1473 Max 0.3334 expVar 0.1072E-02 Bins 167
Light curve ready !
Frme 1 Written to output file : xronos.qlc1
PLT> PLT> PLT> [6]xronos>
-> TIMEDEL=5.0000000000E-01 for ad50006000g300170m.evt
** XSELECT V1.3 **
!> Enter session name >[xsel] xsel
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS PHA_BINS
1 W50 EAST PH MEDIUM 27/04/93 23:50:48 0.12E+05 7421 1024
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS PHA_BINS
1 W50 EAST PH MEDIUM 27/04/93 23:50:48 0.12E+05 7421 1024
2 W50 EAST PH HIGH 28/04/93 03:44:46 0.18E+05 11260 1024
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS PHA_BINS
1 W50 EAST PH MEDIUM 27/04/93 23:50:48 0.12E+05 7421 1024
2 W50 EAST PH HIGH 28/04/93 03:44:46 0.18E+05 11260 1024
3 W50 EAST PH MEDIUM 28/04/93 19:50:32 0.68E+04 4275 1024
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS PHA_BINS
1 W50 EAST PH MEDIUM 27/04/93 23:50:48 0.12E+05 7421 1024
2 W50 EAST PH HIGH 28/04/93 03:44:46 0.18E+05 11260 1024
3 W50 EAST PH MEDIUM 28/04/93 19:50:32 0.68E+04 4275 1024
4 W50 EAST PH HIGH 28/04/93 22:52:30 0.15E+04 1006 1024
EXTRACTOR vers 2.0 11 Apr 1997.
Doing file: /data/data17/seq_proc/50006000.007/ad50006000g300170m.evt
Total Good Bad: Region Time Phase Cut
7421 3081 4340 0 0 0
Writing events file
3081 events written to the output file
Doing file: /data/data17/seq_proc/50006000.007/ad50006000g300270h.evt
Total Good Bad: Region Time Phase Cut
11260 4708 6552 0 0 0
Writing events file
7789 events written to the output file
Doing file: /data/data17/seq_proc/50006000.007/ad50006000g300470m.evt
Total Good Bad: Region Time Phase Cut
4275 1796 2479 0 0 0
Writing events file
9585 events written to the output file
Doing file: /data/data17/seq_proc/50006000.007/ad50006000g300570h.evt
Total Good Bad: Region Time Phase Cut
1006 441 565 0 0 0
Writing events file
10026 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
23962 10026 13936 0 0 0
in 37697.54 seconds
Command not found; type ? for a command listing
!xsel:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!xsel:ASCA > set datadir .
Setting data directory to /data/data17/seq_proc/50006000.007/
Setting mkf directory to /data/data17/seq_proc/50006000.007/
!xsel:ASCA > read events ad50006000g300170m.evt
Got new instrument: GIS3
Setting: IMAGE binning = 1
WMAP binning = 1
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 1023
Got the minimum time resolution of the read data: 0.50000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data17/seq_proc/50006000.007/
HK Directory is: /data/data17/seq_proc/50006000.007/
!xsel:ASCA-GIS3-PH > read events ad50006000g300270h.evt
Getting Min and Max for Energy Column...
Got min and max for PI: 0 1023
Got the minimum time resolution of the read data: 0.62500E-01
Number of files read in: 2
******************** Observation Catalogue ********************
Data Directory is: /data/data17/seq_proc/50006000.007/
HK Directory is: /data/data17/seq_proc/50006000.007/
!xsel:ASCA-GIS3-PH > read events ad50006000g300470m.evt
Getting Min and Max for Energy Column...
Got min and max for PI: 0 1023
Got the minimum time resolution of the read data: 0.50000
Number of files read in: 3
******************** Observation Catalogue ********************
Data Directory is: /data/data17/seq_proc/50006000.007/
HK Directory is: /data/data17/seq_proc/50006000.007/
!xsel:ASCA-GIS3-PH > read events ad50006000g300570h.evt
Getting Min and Max for Energy Column...
Got min and max for PI: 0 1023
Got the minimum time resolution of the read data: 0.62500E-01
Number of files read in: 4
******************** Observation Catalogue ********************
Data Directory is: /data/data17/seq_proc/50006000.007/
HK Directory is: /data/data17/seq_proc/50006000.007/
!xsel:ASCA-GIS3-PH > filter region ad50006000g325670_1.reg
!xsel:ASCA-GIS3-PH > extract events
!xsel:ASCA-GIS3-PH > save events outfile=events.tmp use_events=yes
Wrote events list to file events.tmp
Changing Data directory from:
/data/data17/seq_proc/50006000.007/
to the current working directory.
!xsel:ASCA-GIS3-PH > exit save_session=no
-> Extracting ad50006000g300070_1.lc with binsize 187.99889584414
** XSELECT V1.3 **
!> Enter session name >[xsel] xsel
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS PHA_BINS
1 W50 EAST PH MEDIUM 27/04/93 23:50:48 0.38E+05 10026 1024
EXTRACTOR vers 2.0 11 Apr 1997.
Doing file: /data/data17/seq_proc/50006000.007/events.tmp
Total Good Bad: Region Time Phase Cut
10026 10026 0 0 0 0
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
10026 10026 0 0 0 0
in 37697.54 seconds
Fits light curve has 10026 counts for 0.2660 counts/sec
Command not found; type ? for a command listing
!xsel:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!xsel:ASCA > set datadir .
Setting data directory to /data/data17/seq_proc/50006000.007/
Setting mkf directory to /data/data17/seq_proc/50006000.007/
!xsel:ASCA > read events events.tmp
Got new instrument: GIS3
Setting: IMAGE binning = 1
WMAP binning = 1
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 1023
Got the minimum time resolution of the read data: 0.50000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data17/seq_proc/50006000.007/
HK Directory is: /data/data17/seq_proc/50006000.007/
!xsel:ASCA-GIS3-PH > set binsize 187.99889584414
!xsel:ASCA-GIS3-PH > extract curve exposure=0.5
!xsel:ASCA-GIS3-PH > save curve ad50006000g300070_1.lc
Wrote FITS light curve to file ad50006000g300070_1.lc
!xsel:ASCA-GIS3-PH > exit save_session=no
-> Plotting light curve ad50006000g300070_1_lc.ps
Type "help" for information
[1]xronos> Current User Interface is ; command driven
[2]xronos> Enter up to 50 input filenames and options for series 1 (or rtn)
Ser. A filename 1 +options[.rbf]=> ad50006000g300070_1.lc
Selected FITS extensions: 1 - RATE TABLE;
Source ............ W50 EAST LOBE (P Start Time (d) .... 9105 00:05:44.723
FITS Extension .... 1 - `RATE ` Stop Time (d) ..... 9105 23:27:28.499
No. of Rows ....... 206 Bin Time (s) ...... 188.0
Right Ascension ... 2.8844E+02 Internal time sys.. Converted to TJD
Declination ....... 4.9767E+00 Experiment ........ ASCA GIS3
Corrections applied: Vignetting - No ; Deadtime - No ; Bkgd - No ; Clock - No
Selected Columns: 1 - Time; 2 - Y-axis; 3 - Y-error;
File contains binned data.
Ser. A filename 2 +options[.rbf]=>
Enter up to 50 input filenames and options for series 2 (or rtn)
Ser. B filename 1 +options[.rbf]=>
Enter up to 50 input filenames and options for series 3 (or rtn)
Ser. C filename 1 +options[.rbf]=>
[3]xronos>
Maximum of 1 Intvs. with 448 Newbins of 187.999 (s)
Intv 1 Start 9105 0: 7:18
Ser.1 Avg 0.2663 Chisq 186.1 Var 0.1384E-02 Newbs. 206
Min 0.1758 Max 0.3916 expVar 0.1532E-02 Bins 206
Results from Statistical Analysis
Newbin Integration Time (s).. 188.00
Interval Duration (s)........ 83848.
No. of Newbins .............. 206
Average (c/s) ............... 0.26631 +/- 0.27E-02
Standard Deviation (c/s)..... 0.37197E-01
Minimum (c/s)................ 0.17580
Maximum (c/s)................ 0.39162
Variance ((c/s)**2).......... 0.13836E-02 +/- 0.14E-03
Expected Variance ((c/s)**2). 0.15317E-02 +/- 0.15E-03
Third Moment ((c/s)**3)...... 0.12280E-04
Average Deviation (c/s)...... 0.29328E-01
Skewness..................... 0.23859 +/- 0.17
Kurtosis..................... 0.15349 +/- 0.34
RMS fractional variation....< 0.95166E-01 (3 sigma)
Chi-Square................... 186.08 dof 205
Chi-Square Prob of constancy. 0.82419 (0 means < 1.e-38)
Kolm.-Smir. Prob of constancy 0.52319 (0 means < 1.e-38)
[4]xronos> [5]xronos>
Maximum of 1 Intvs. with 448 Newbins of 187.999 (s)
Intv 1 Start 9105 0: 7:18
Ser.1 Avg 0.2663 Chisq 186.1 Var 0.1384E-02 Newbs. 206
Min 0.1758 Max 0.3916 expVar 0.1532E-02 Bins 206
Light curve ready !
Frme 1 Written to output file : xronos.qlc1
PLT> PLT> PLT> [6]xronos>
-> Merging GTIs from the following files:ad50006000g200170m.evt[2] ad50006000g200270h.evt[2] ad50006000g200470m.evt[2] ad50006000g200570h.evt[2]-> Making L1 light curve of ft930427_2350_1950G2HK.fits with irate=HIGH
ghkcurve: ALLGTI found in input HK file, will be applied to data. ghkcurve: 40511 output records from 40542 good input G2_L1 records.-> Making L1 light curve of ft930427_2350_1950G2HK.fits with irate=HI+MED
ghkcurve: ALLGTI found in input HK file, will be applied to data. ghkcurve: 27342 output records from 51405 good input G2_L1 records.-> Making L1 light curve of ft930428_1949_2350G2HK.fits with irate=HIGH
ghkcurve: ALLGTI found in input HK file, will be applied to data. ghkcurve: 3321 output records from 3322 good input G2_L1 records.-> Making L1 light curve of ft930428_1949_2350G2HK.fits with irate=HI+MED
ghkcurve: ALLGTI found in input HK file, will be applied to data. ghkcurve: 7641 output records from 9562 good input G2_L1 records.-> Merging GTIs from the following files:
ad50006000g300170m.evt[2] ad50006000g300270h.evt[2] ad50006000g300470m.evt[2] ad50006000g300570h.evt[2]-> Making L1 light curve of ft930427_2350_1950G3HK.fits with irate=HIGH
ghkcurve: ALLGTI found in input HK file, will be applied to data. ghkcurve: 39033 output records from 39066 good input G3_L1 records.-> Making L1 light curve of ft930427_2350_1950G3HK.fits with irate=HI+MED
ghkcurve: ALLGTI found in input HK file, will be applied to data. ghkcurve: 27052 output records from 49774 good input G3_L1 records.-> Making L1 light curve of ft930428_1949_2350G3HK.fits with irate=HIGH
ghkcurve: ALLGTI found in input HK file, will be applied to data. ghkcurve: 3167 output records from 3168 good input G3_L1 records.-> Making L1 light curve of ft930428_1949_2350G3HK.fits with irate=HI+MED
ghkcurve: ALLGTI found in input HK file, will be applied to data. ghkcurve: 7619 output records from 9412 good input G3_L1 records.
** XSELECT V1.3 **
!> Enter session name >[xsel] xsel
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS PHA_BINS
1 W50 EAST PH MEDIUM 27/04/93 23:50:48 0.12E+05 7555 1024
EXTRACTOR vers 2.0 11 Apr 1997.
Doing file: /data/data17/seq_proc/50006000.007/ad50006000g200170m.evt
Total Good Bad: Region Time Phase Cut
7555 2557 4998 0 0 0
Writing events file
2557 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
7555 2557 4998 0 0 0
in 11599.79 seconds
Command not found; type ? for a command listing
!xsel:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!xsel:ASCA > set datadir .
Setting data directory to /data/data17/seq_proc/50006000.007/
Setting mkf directory to /data/data17/seq_proc/50006000.007/
!xsel:ASCA > read events ad50006000g200170m.evt
Got new instrument: GIS2
Setting: IMAGE binning = 1
WMAP binning = 1
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 1023
Got the minimum time resolution of the read data: 0.50000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data17/seq_proc/50006000.007/
HK Directory is: /data/data17/seq_proc/50006000.007/
!xsel:ASCA-GIS2-PH > filter region ad50006000g225670_1.reg
!xsel:ASCA-GIS2-PH > extract events
!xsel:ASCA-GIS2-PH > save events outfile=ad50006000g200170m_1.ulc use_events=yes
Wrote events list to file ad50006000g200170m_1.ulc
Changing Data directory from:
/data/data17/seq_proc/50006000.007/
to the current working directory.
!xsel:ASCA-GIS2-PH > exit save_session=no
-> Extracting unbinned light curve ad50006000g200270h_1.ulc
** XSELECT V1.3 **
!> Enter session name >[xsel] xsel
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS PHA_BINS
1 W50 EAST PH HIGH 28/04/93 03:44:46 0.18E+05 11655 1024
EXTRACTOR vers 2.0 11 Apr 1997.
Doing file: /data/data17/seq_proc/50006000.007/ad50006000g200270h.evt
Total Good Bad: Region Time Phase Cut
11655 4030 7625 0 0 0
Writing events file
4030 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
11655 4030 7625 0 0 0
in 17795.72 seconds
Command not found; type ? for a command listing
!xsel:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!xsel:ASCA > set datadir .
Setting data directory to /data/data17/seq_proc/50006000.007/
Setting mkf directory to /data/data17/seq_proc/50006000.007/
!xsel:ASCA > read events ad50006000g200270h.evt
Got new instrument: GIS2
Setting: IMAGE binning = 1
WMAP binning = 1
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 1023
Got the minimum time resolution of the read data: 0.62500E-01
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data17/seq_proc/50006000.007/
HK Directory is: /data/data17/seq_proc/50006000.007/
!xsel:ASCA-GIS2-PH > filter region ad50006000g225670_1.reg
!xsel:ASCA-GIS2-PH > extract events
!xsel:ASCA-GIS2-PH > save events outfile=ad50006000g200270h_1.ulc use_events=yes
Wrote events list to file ad50006000g200270h_1.ulc
Changing Data directory from:
/data/data17/seq_proc/50006000.007/
to the current working directory.
!xsel:ASCA-GIS2-PH > exit save_session=no
-> Extracting unbinned light curve ad50006000g200470m_1.ulc
** XSELECT V1.3 **
!> Enter session name >[xsel] xsel
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS PHA_BINS
1 W50 EAST PH MEDIUM 28/04/93 19:50:32 0.68E+04 4255 1024
EXTRACTOR vers 2.0 11 Apr 1997.
Doing file: /data/data17/seq_proc/50006000.007/ad50006000g200470m.evt
Total Good Bad: Region Time Phase Cut
4255 1431 2824 0 0 0
Writing events file
1431 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
4255 1431 2824 0 0 0
in 6768.03 seconds
Command not found; type ? for a command listing
!xsel:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!xsel:ASCA > set datadir .
Setting data directory to /data/data17/seq_proc/50006000.007/
Setting mkf directory to /data/data17/seq_proc/50006000.007/
!xsel:ASCA > read events ad50006000g200470m.evt
Got new instrument: GIS2
Setting: IMAGE binning = 1
WMAP binning = 1
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 1023
Got the minimum time resolution of the read data: 0.50000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data17/seq_proc/50006000.007/
HK Directory is: /data/data17/seq_proc/50006000.007/
!xsel:ASCA-GIS2-PH > filter region ad50006000g225670_1.reg
!xsel:ASCA-GIS2-PH > extract events
!xsel:ASCA-GIS2-PH > save events outfile=ad50006000g200470m_1.ulc use_events=yes
Wrote events list to file ad50006000g200470m_1.ulc
Changing Data directory from:
/data/data17/seq_proc/50006000.007/
to the current working directory.
!xsel:ASCA-GIS2-PH > exit save_session=no
-> Extracting unbinned light curve ad50006000g200570h_1.ulc
** XSELECT V1.3 **
!> Enter session name >[xsel] xsel
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS PHA_BINS
1 W50 EAST PH HIGH 28/04/93 22:52:30 0.15E+04 1004 1024
EXTRACTOR vers 2.0 11 Apr 1997.
Doing file: /data/data17/seq_proc/50006000.007/ad50006000g200570h.evt
Total Good Bad: Region Time Phase Cut
1004 360 644 0 0 0
Writing events file
360 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
1004 360 644 0 0 0
in 1530.00 seconds
Command not found; type ? for a command listing
!xsel:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!xsel:ASCA > set datadir .
Setting data directory to /data/data17/seq_proc/50006000.007/
Setting mkf directory to /data/data17/seq_proc/50006000.007/
!xsel:ASCA > read events ad50006000g200570h.evt
Got new instrument: GIS2
Setting: IMAGE binning = 1
WMAP binning = 1
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 1023
Got the minimum time resolution of the read data: 0.62500E-01
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data17/seq_proc/50006000.007/
HK Directory is: /data/data17/seq_proc/50006000.007/
!xsel:ASCA-GIS2-PH > filter region ad50006000g225670_1.reg
!xsel:ASCA-GIS2-PH > extract events
!xsel:ASCA-GIS2-PH > save events outfile=ad50006000g200570h_1.ulc use_events=yes
Wrote events list to file ad50006000g200570h_1.ulc
Changing Data directory from:
/data/data17/seq_proc/50006000.007/
to the current working directory.
!xsel:ASCA-GIS2-PH > exit save_session=no
-> Extracting unbinned light curve ad50006000g300170m_1.ulc
** XSELECT V1.3 **
!> Enter session name >[xsel] xsel
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS PHA_BINS
1 W50 EAST PH MEDIUM 27/04/93 23:50:48 0.12E+05 7421 1024
EXTRACTOR vers 2.0 11 Apr 1997.
Doing file: /data/data17/seq_proc/50006000.007/ad50006000g300170m.evt
Total Good Bad: Region Time Phase Cut
7421 3081 4340 0 0 0
Writing events file
3081 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
7421 3081 4340 0 0 0
in 11599.79 seconds
Command not found; type ? for a command listing
!xsel:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!xsel:ASCA > set datadir .
Setting data directory to /data/data17/seq_proc/50006000.007/
Setting mkf directory to /data/data17/seq_proc/50006000.007/
!xsel:ASCA > read events ad50006000g300170m.evt
Got new instrument: GIS3
Setting: IMAGE binning = 1
WMAP binning = 1
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 1023
Got the minimum time resolution of the read data: 0.50000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data17/seq_proc/50006000.007/
HK Directory is: /data/data17/seq_proc/50006000.007/
!xsel:ASCA-GIS3-PH > filter region ad50006000g325670_1.reg
!xsel:ASCA-GIS3-PH > extract events
!xsel:ASCA-GIS3-PH > save events outfile=ad50006000g300170m_1.ulc use_events=yes
Wrote events list to file ad50006000g300170m_1.ulc
Changing Data directory from:
/data/data17/seq_proc/50006000.007/
to the current working directory.
!xsel:ASCA-GIS3-PH > exit save_session=no
-> Extracting unbinned light curve ad50006000g300270h_1.ulc
** XSELECT V1.3 **
!> Enter session name >[xsel] xsel
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS PHA_BINS
1 W50 EAST PH HIGH 28/04/93 03:44:46 0.18E+05 11260 1024
EXTRACTOR vers 2.0 11 Apr 1997.
Doing file: /data/data17/seq_proc/50006000.007/ad50006000g300270h.evt
Total Good Bad: Region Time Phase Cut
11260 4708 6552 0 0 0
Writing events file
4708 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
11260 4708 6552 0 0 0
in 17799.72 seconds
Command not found; type ? for a command listing
!xsel:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!xsel:ASCA > set datadir .
Setting data directory to /data/data17/seq_proc/50006000.007/
Setting mkf directory to /data/data17/seq_proc/50006000.007/
!xsel:ASCA > read events ad50006000g300270h.evt
Got new instrument: GIS3
Setting: IMAGE binning = 1
WMAP binning = 1
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 1023
Got the minimum time resolution of the read data: 0.62500E-01
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data17/seq_proc/50006000.007/
HK Directory is: /data/data17/seq_proc/50006000.007/
!xsel:ASCA-GIS3-PH > filter region ad50006000g325670_1.reg
!xsel:ASCA-GIS3-PH > extract events
!xsel:ASCA-GIS3-PH > save events outfile=ad50006000g300270h_1.ulc use_events=yes
Wrote events list to file ad50006000g300270h_1.ulc
Changing Data directory from:
/data/data17/seq_proc/50006000.007/
to the current working directory.
!xsel:ASCA-GIS3-PH > exit save_session=no
-> Extracting unbinned light curve ad50006000g300470m_1.ulc
** XSELECT V1.3 **
!> Enter session name >[xsel] xsel
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS PHA_BINS
1 W50 EAST PH MEDIUM 28/04/93 19:50:32 0.68E+04 4275 1024
EXTRACTOR vers 2.0 11 Apr 1997.
Doing file: /data/data17/seq_proc/50006000.007/ad50006000g300470m.evt
Total Good Bad: Region Time Phase Cut
4275 1796 2479 0 0 0
Writing events file
1796 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
4275 1796 2479 0 0 0
in 6768.03 seconds
Command not found; type ? for a command listing
!xsel:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!xsel:ASCA > set datadir .
Setting data directory to /data/data17/seq_proc/50006000.007/
Setting mkf directory to /data/data17/seq_proc/50006000.007/
!xsel:ASCA > read events ad50006000g300470m.evt
Got new instrument: GIS3
Setting: IMAGE binning = 1
WMAP binning = 1
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 1023
Got the minimum time resolution of the read data: 0.50000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data17/seq_proc/50006000.007/
HK Directory is: /data/data17/seq_proc/50006000.007/
!xsel:ASCA-GIS3-PH > filter region ad50006000g325670_1.reg
!xsel:ASCA-GIS3-PH > extract events
!xsel:ASCA-GIS3-PH > save events outfile=ad50006000g300470m_1.ulc use_events=yes
Wrote events list to file ad50006000g300470m_1.ulc
Changing Data directory from:
/data/data17/seq_proc/50006000.007/
to the current working directory.
!xsel:ASCA-GIS3-PH > exit save_session=no
-> Extracting unbinned light curve ad50006000g300570h_1.ulc
** XSELECT V1.3 **
!> Enter session name >[xsel] xsel
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS PHA_BINS
1 W50 EAST PH HIGH 28/04/93 22:52:30 0.15E+04 1006 1024
EXTRACTOR vers 2.0 11 Apr 1997.
Doing file: /data/data17/seq_proc/50006000.007/ad50006000g300570h.evt
Total Good Bad: Region Time Phase Cut
1006 441 565 0 0 0
Writing events file
441 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
1006 441 565 0 0 0
in 1530.00 seconds
Command not found; type ? for a command listing
!xsel:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!xsel:ASCA > set datadir .
Setting data directory to /data/data17/seq_proc/50006000.007/
Setting mkf directory to /data/data17/seq_proc/50006000.007/
!xsel:ASCA > read events ad50006000g300570h.evt
Got new instrument: GIS3
Setting: IMAGE binning = 1
WMAP binning = 1
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 1023
Got the minimum time resolution of the read data: 0.62500E-01
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data17/seq_proc/50006000.007/
HK Directory is: /data/data17/seq_proc/50006000.007/
!xsel:ASCA-GIS3-PH > filter region ad50006000g325670_1.reg
!xsel:ASCA-GIS3-PH > extract events
!xsel:ASCA-GIS3-PH > save events outfile=ad50006000g300570h_1.ulc use_events=yes
Wrote events list to file ad50006000g300570h_1.ulc
Changing Data directory from:
/data/data17/seq_proc/50006000.007/
to the current working directory.
!xsel:ASCA-GIS3-PH > exit save_session=no
-> Extracting unbinned light curve ad50006000s000102h_1.ulc
** XSELECT V1.3 **
!> Enter session name >[xsel] xsel
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS S0CCDPOW
1 W50 EAST BRIGHT HIGH 28/04/93 03:44:28 0.16E+05 10231 1111
EXTRACTOR vers 2.0 11 Apr 1997.
Doing file: /data/data17/seq_proc/50006000.007/ad50006000s000102h.evt
Total Good Bad: Region Time Phase Cut
10231 6357 3874 0 0 0
Writing events file
6357 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
10231 6357 3874 0 0 0
in 15568.82 seconds
Command not found; type ? for a command listing
!xsel:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!xsel:ASCA > set datadir .
Setting data directory to /data/data17/seq_proc/50006000.007/
Setting mkf directory to /data/data17/seq_proc/50006000.007/
!xsel:ASCA > read events ad50006000s000102h.evt
Got new instrument: SIS0
Setting: IMAGE binning = 4
WMAP binning = 8
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 2047
Got the minimum time resolution of the read data: 16.000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data17/seq_proc/50006000.007/
HK Directory is: /data/data17/seq_proc/50006000.007/
!xsel:ASCA-SIS0-BRIGHT > filter region ad50006000s032002_1.reg
!xsel:ASCA-SIS0-BRIGHT > extract events
!xsel:ASCA-SIS0-BRIGHT > save events outfile=ad50006000s000102h_1.ulc use_events=yes
Wrote events list to file ad50006000s000102h_1.ulc
Changing Data directory from:
/data/data17/seq_proc/50006000.007/
to the current working directory.
!xsel:ASCA-SIS0-BRIGHT > exit save_session=no
-> Extracting unbinned light curve ad50006000s000112h_1.ulc
** XSELECT V1.3 **
!> Enter session name >[xsel] xsel
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS S0CCDPOW
1 W50 EAST BRIGHT2 HIGH 28/04/93 03:44:28 0.16E+05 10514 1111
EXTRACTOR vers 2.0 11 Apr 1997.
Doing file: /data/data17/seq_proc/50006000.007/ad50006000s000112h.evt
Total Good Bad: Region Time Phase Cut
10514 6519 3995 0 0 0
Writing events file
6519 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
10514 6519 3995 0 0 0
in 15568.82 seconds
Command not found; type ? for a command listing
!xsel:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!xsel:ASCA > set datadir .
Setting data directory to /data/data17/seq_proc/50006000.007/
Setting mkf directory to /data/data17/seq_proc/50006000.007/
!xsel:ASCA > read events ad50006000s000112h.evt
Got new instrument: SIS0
Setting: IMAGE binning = 4
WMAP binning = 8
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 4095
Got the minimum time resolution of the read data: 16.000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data17/seq_proc/50006000.007/
HK Directory is: /data/data17/seq_proc/50006000.007/
!xsel:ASCA-SIS0-BRIGHT2 > filter region ad50006000s032002_1.reg
!xsel:ASCA-SIS0-BRIGHT2 > extract events
!xsel:ASCA-SIS0-BRIGHT2 > save events outfile=ad50006000s000112h_1.ulc use_events=yes
Wrote events list to file ad50006000s000112h_1.ulc
Changing Data directory from:
/data/data17/seq_proc/50006000.007/
to the current working directory.
!xsel:ASCA-SIS0-BRIGHT2 > exit save_session=no
-> Extracting unbinned light curve ad50006000s000202m_1.ulc
** XSELECT V1.3 **
!> Enter session name >[xsel] xsel
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS S0CCDPOW
1 W50 EAST BRIGHT MEDIUM 27/04/93 23:50:32 0.11E+05 7322 1111
EXTRACTOR vers 2.0 11 Apr 1997.
Doing file: /data/data17/seq_proc/50006000.007/ad50006000s000202m.evt
Total Good Bad: Region Time Phase Cut
7322 4449 2873 0 0 0
Writing events file
4449 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
7322 4449 2873 0 0 0
in 11070.42 seconds
Command not found; type ? for a command listing
!xsel:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!xsel:ASCA > set datadir .
Setting data directory to /data/data17/seq_proc/50006000.007/
Setting mkf directory to /data/data17/seq_proc/50006000.007/
!xsel:ASCA > read events ad50006000s000202m.evt
Got new instrument: SIS0
Setting: IMAGE binning = 4
WMAP binning = 8
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 2047
Got the minimum time resolution of the read data: 16.000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data17/seq_proc/50006000.007/
HK Directory is: /data/data17/seq_proc/50006000.007/
!xsel:ASCA-SIS0-BRIGHT > filter region ad50006000s032002_1.reg
!xsel:ASCA-SIS0-BRIGHT > extract events
!xsel:ASCA-SIS0-BRIGHT > save events outfile=ad50006000s000202m_1.ulc use_events=yes
Wrote events list to file ad50006000s000202m_1.ulc
Changing Data directory from:
/data/data17/seq_proc/50006000.007/
to the current working directory.
!xsel:ASCA-SIS0-BRIGHT > exit save_session=no
-> Extracting unbinned light curve ad50006000s000302h_1.ulc
** XSELECT V1.3 **
!> Enter session name >[xsel] xsel
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS S0CCDPOW
1 W50 EAST BRIGHT HIGH 28/04/93 14:34:00 0.19E+04 1341 1011
EXTRACTOR vers 2.0 11 Apr 1997.
Doing file: /data/data17/seq_proc/50006000.007/ad50006000s000302h.evt
Total Good Bad: Region Time Phase Cut
1341 835 506 0 0 0
Writing events file
835 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
1341 835 506 0 0 0
in 1939.59 seconds
Command not found; type ? for a command listing
!xsel:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!xsel:ASCA > set datadir .
Setting data directory to /data/data17/seq_proc/50006000.007/
Setting mkf directory to /data/data17/seq_proc/50006000.007/
!xsel:ASCA > read events ad50006000s000302h.evt
Got new instrument: SIS0
Setting: IMAGE binning = 4
WMAP binning = 8
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 2047
Got the minimum time resolution of the read data: 16.000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data17/seq_proc/50006000.007/
HK Directory is: /data/data17/seq_proc/50006000.007/
!xsel:ASCA-SIS0-BRIGHT > filter region ad50006000s032002_1.reg
!xsel:ASCA-SIS0-BRIGHT > extract events
!xsel:ASCA-SIS0-BRIGHT > save events outfile=ad50006000s000302h_1.ulc use_events=yes
Wrote events list to file ad50006000s000302h_1.ulc
Changing Data directory from:
/data/data17/seq_proc/50006000.007/
to the current working directory.
!xsel:ASCA-SIS0-BRIGHT > exit save_session=no
-> Extracting unbinned light curve ad50006000s000312h_1.ulc
** XSELECT V1.3 **
!> Enter session name >[xsel] xsel
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS S0CCDPOW
1 W50 EAST BRIGHT2 HIGH 28/04/93 14:34:00 0.19E+04 1370 1011
EXTRACTOR vers 2.0 11 Apr 1997.
Doing file: /data/data17/seq_proc/50006000.007/ad50006000s000312h.evt
Total Good Bad: Region Time Phase Cut
1370 856 514 0 0 0
Writing events file
856 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
1370 856 514 0 0 0
in 1939.59 seconds
Command not found; type ? for a command listing
!xsel:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!xsel:ASCA > set datadir .
Setting data directory to /data/data17/seq_proc/50006000.007/
Setting mkf directory to /data/data17/seq_proc/50006000.007/
!xsel:ASCA > read events ad50006000s000312h.evt
Got new instrument: SIS0
Setting: IMAGE binning = 4
WMAP binning = 8
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 4095
Got the minimum time resolution of the read data: 16.000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data17/seq_proc/50006000.007/
HK Directory is: /data/data17/seq_proc/50006000.007/
!xsel:ASCA-SIS0-BRIGHT2 > filter region ad50006000s032002_1.reg
!xsel:ASCA-SIS0-BRIGHT2 > extract events
!xsel:ASCA-SIS0-BRIGHT2 > save events outfile=ad50006000s000312h_1.ulc use_events=yes
Wrote events list to file ad50006000s000312h_1.ulc
Changing Data directory from:
/data/data17/seq_proc/50006000.007/
to the current working directory.
!xsel:ASCA-SIS0-BRIGHT2 > exit save_session=no
-> Extracting unbinned light curve ad50006000s000502m_1.ulc
** XSELECT V1.3 **
!> Enter session name >[xsel] xsel
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS S0CCDPOW
1 W50 EAST BRIGHT MEDIUM 28/04/93 19:50:16 0.55E+04 3663 1111
EXTRACTOR vers 2.0 11 Apr 1997.
Doing file: /data/data17/seq_proc/50006000.007/ad50006000s000502m.evt
Total Good Bad: Region Time Phase Cut
3663 2223 1440 0 0 0
Writing events file
2223 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
3663 2223 1440 0 0 0
in 5512.04 seconds
Command not found; type ? for a command listing
!xsel:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!xsel:ASCA > set datadir .
Setting data directory to /data/data17/seq_proc/50006000.007/
Setting mkf directory to /data/data17/seq_proc/50006000.007/
!xsel:ASCA > read events ad50006000s000502m.evt
Got new instrument: SIS0
Setting: IMAGE binning = 4
WMAP binning = 8
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 2047
Got the minimum time resolution of the read data: 16.000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data17/seq_proc/50006000.007/
HK Directory is: /data/data17/seq_proc/50006000.007/
!xsel:ASCA-SIS0-BRIGHT > filter region ad50006000s032002_1.reg
!xsel:ASCA-SIS0-BRIGHT > extract events
!xsel:ASCA-SIS0-BRIGHT > save events outfile=ad50006000s000502m_1.ulc use_events=yes
Wrote events list to file ad50006000s000502m_1.ulc
Changing Data directory from:
/data/data17/seq_proc/50006000.007/
to the current working directory.
!xsel:ASCA-SIS0-BRIGHT > exit save_session=no
-> Extracting unbinned light curve ad50006000s000602h_1.ulc
** XSELECT V1.3 **
!> Enter session name >[xsel] xsel
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS S0CCDPOW
1 W50 EAST BRIGHT HIGH 28/04/93 22:52:12 0.15E+04 976 1111
EXTRACTOR vers 2.0 11 Apr 1997.
Doing file: /data/data17/seq_proc/50006000.007/ad50006000s000602h.evt
Total Good Bad: Region Time Phase Cut
976 626 350 0 0 0
Writing events file
626 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
976 626 350 0 0 0
in 1453.93 seconds
Command not found; type ? for a command listing
!xsel:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!xsel:ASCA > set datadir .
Setting data directory to /data/data17/seq_proc/50006000.007/
Setting mkf directory to /data/data17/seq_proc/50006000.007/
!xsel:ASCA > read events ad50006000s000602h.evt
Got new instrument: SIS0
Setting: IMAGE binning = 4
WMAP binning = 8
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 2047
Got the minimum time resolution of the read data: 16.000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data17/seq_proc/50006000.007/
HK Directory is: /data/data17/seq_proc/50006000.007/
!xsel:ASCA-SIS0-BRIGHT > filter region ad50006000s032002_1.reg
!xsel:ASCA-SIS0-BRIGHT > extract events
!xsel:ASCA-SIS0-BRIGHT > save events outfile=ad50006000s000602h_1.ulc use_events=yes
Wrote events list to file ad50006000s000602h_1.ulc
Changing Data directory from:
/data/data17/seq_proc/50006000.007/
to the current working directory.
!xsel:ASCA-SIS0-BRIGHT > exit save_session=no
-> Extracting unbinned light curve ad50006000s000612h_1.ulc
** XSELECT V1.3 **
!> Enter session name >[xsel] xsel
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS S0CCDPOW
1 W50 EAST BRIGHT2 HIGH 28/04/93 22:52:12 0.15E+04 1006 1111
EXTRACTOR vers 2.0 11 Apr 1997.
Doing file: /data/data17/seq_proc/50006000.007/ad50006000s000612h.evt
Total Good Bad: Region Time Phase Cut
1006 638 368 0 0 0
Writing events file
638 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
1006 638 368 0 0 0
in 1453.93 seconds
Command not found; type ? for a command listing
!xsel:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!xsel:ASCA > set datadir .
Setting data directory to /data/data17/seq_proc/50006000.007/
Setting mkf directory to /data/data17/seq_proc/50006000.007/
!xsel:ASCA > read events ad50006000s000612h.evt
Got new instrument: SIS0
Setting: IMAGE binning = 4
WMAP binning = 8
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 4095
Got the minimum time resolution of the read data: 16.000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data17/seq_proc/50006000.007/
HK Directory is: /data/data17/seq_proc/50006000.007/
!xsel:ASCA-SIS0-BRIGHT2 > filter region ad50006000s032002_1.reg
!xsel:ASCA-SIS0-BRIGHT2 > extract events
!xsel:ASCA-SIS0-BRIGHT2 > save events outfile=ad50006000s000612h_1.ulc use_events=yes
Wrote events list to file ad50006000s000612h_1.ulc
Changing Data directory from:
/data/data17/seq_proc/50006000.007/
to the current working directory.
!xsel:ASCA-SIS0-BRIGHT2 > exit save_session=no
-> Extracting unbinned light curve ad50006000s100102h_1.ulc
** XSELECT V1.3 **
!> Enter session name >[xsel] xsel
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS S1CCDPOW
1 W50 EAST BRIGHT HIGH 28/04/93 03:44:28 0.18E+05 12214 1111
EXTRACTOR vers 2.0 11 Apr 1997.
Doing file: /data/data17/seq_proc/50006000.007/ad50006000s100102h.evt
Total Good Bad: Region Time Phase Cut
12214 7764 4450 0 0 0
Writing events file
7764 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
12214 7764 4450 0 0 0
in 17516.77 seconds
Command not found; type ? for a command listing
!xsel:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!xsel:ASCA > set datadir .
Setting data directory to /data/data17/seq_proc/50006000.007/
Setting mkf directory to /data/data17/seq_proc/50006000.007/
!xsel:ASCA > read events ad50006000s100102h.evt
Got new instrument: SIS1
Setting: IMAGE binning = 4
WMAP binning = 8
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 2047
Got the minimum time resolution of the read data: 16.000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data17/seq_proc/50006000.007/
HK Directory is: /data/data17/seq_proc/50006000.007/
!xsel:ASCA-SIS1-BRIGHT > filter region ad50006000s132002_1.reg
!xsel:ASCA-SIS1-BRIGHT > extract events
!xsel:ASCA-SIS1-BRIGHT > save events outfile=ad50006000s100102h_1.ulc use_events=yes
Wrote events list to file ad50006000s100102h_1.ulc
Changing Data directory from:
/data/data17/seq_proc/50006000.007/
to the current working directory.
!xsel:ASCA-SIS1-BRIGHT > exit save_session=no
-> Extracting unbinned light curve ad50006000s100112h_1.ulc
** XSELECT V1.3 **
!> Enter session name >[xsel] xsel
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS S1CCDPOW
1 W50 EAST BRIGHT2 HIGH 28/04/93 03:44:28 0.18E+05 12482 1111
EXTRACTOR vers 2.0 11 Apr 1997.
Doing file: /data/data17/seq_proc/50006000.007/ad50006000s100112h.evt
Total Good Bad: Region Time Phase Cut
12482 7902 4580 0 0 0
Writing events file
7902 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
12482 7902 4580 0 0 0
in 17516.77 seconds
Command not found; type ? for a command listing
!xsel:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!xsel:ASCA > set datadir .
Setting data directory to /data/data17/seq_proc/50006000.007/
Setting mkf directory to /data/data17/seq_proc/50006000.007/
!xsel:ASCA > read events ad50006000s100112h.evt
Got new instrument: SIS1
Setting: IMAGE binning = 4
WMAP binning = 8
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 4095
Got the minimum time resolution of the read data: 16.000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data17/seq_proc/50006000.007/
HK Directory is: /data/data17/seq_proc/50006000.007/
!xsel:ASCA-SIS1-BRIGHT2 > filter region ad50006000s132002_1.reg
!xsel:ASCA-SIS1-BRIGHT2 > extract events
!xsel:ASCA-SIS1-BRIGHT2 > save events outfile=ad50006000s100112h_1.ulc use_events=yes
Wrote events list to file ad50006000s100112h_1.ulc
Changing Data directory from:
/data/data17/seq_proc/50006000.007/
to the current working directory.
!xsel:ASCA-SIS1-BRIGHT2 > exit save_session=no
-> Extracting unbinned light curve ad50006000s100202m_1.ulc
** XSELECT V1.3 **
!> Enter session name >[xsel] xsel
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS S1CCDPOW
1 W50 EAST BRIGHT MEDIUM 27/04/93 23:50:32 0.11E+05 7884 1111
EXTRACTOR vers 2.0 11 Apr 1997.
Doing file: /data/data17/seq_proc/50006000.007/ad50006000s100202m.evt
Total Good Bad: Region Time Phase Cut
7884 5051 2833 0 0 0
Writing events file
5051 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
7884 5051 2833 0 0 0
in 11101.56 seconds
Command not found; type ? for a command listing
!xsel:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!xsel:ASCA > set datadir .
Setting data directory to /data/data17/seq_proc/50006000.007/
Setting mkf directory to /data/data17/seq_proc/50006000.007/
!xsel:ASCA > read events ad50006000s100202m.evt
Got new instrument: SIS1
Setting: IMAGE binning = 4
WMAP binning = 8
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 2047
Got the minimum time resolution of the read data: 16.000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data17/seq_proc/50006000.007/
HK Directory is: /data/data17/seq_proc/50006000.007/
!xsel:ASCA-SIS1-BRIGHT > filter region ad50006000s132002_1.reg
!xsel:ASCA-SIS1-BRIGHT > extract events
!xsel:ASCA-SIS1-BRIGHT > save events outfile=ad50006000s100202m_1.ulc use_events=yes
Wrote events list to file ad50006000s100202m_1.ulc
Changing Data directory from:
/data/data17/seq_proc/50006000.007/
to the current working directory.
!xsel:ASCA-SIS1-BRIGHT > exit save_session=no
-> Extracting unbinned light curve ad50006000s100502m_1.ulc
** XSELECT V1.3 **
!> Enter session name >[xsel] xsel
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS S1CCDPOW
1 W50 EAST BRIGHT MEDIUM 28/04/93 19:50:16 0.56E+04 4002 1111
EXTRACTOR vers 2.0 11 Apr 1997.
Doing file: /data/data17/seq_proc/50006000.007/ad50006000s100502m.evt
Total Good Bad: Region Time Phase Cut
4002 2526 1476 0 0 0
Writing events file
2526 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
4002 2526 1476 0 0 0
in 5608.04 seconds
Command not found; type ? for a command listing
!xsel:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!xsel:ASCA > set datadir .
Setting data directory to /data/data17/seq_proc/50006000.007/
Setting mkf directory to /data/data17/seq_proc/50006000.007/
!xsel:ASCA > read events ad50006000s100502m.evt
Got new instrument: SIS1
Setting: IMAGE binning = 4
WMAP binning = 8
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 2047
Got the minimum time resolution of the read data: 16.000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data17/seq_proc/50006000.007/
HK Directory is: /data/data17/seq_proc/50006000.007/
!xsel:ASCA-SIS1-BRIGHT > filter region ad50006000s132002_1.reg
!xsel:ASCA-SIS1-BRIGHT > extract events
!xsel:ASCA-SIS1-BRIGHT > save events outfile=ad50006000s100502m_1.ulc use_events=yes
Wrote events list to file ad50006000s100502m_1.ulc
Changing Data directory from:
/data/data17/seq_proc/50006000.007/
to the current working directory.
!xsel:ASCA-SIS1-BRIGHT > exit save_session=no
-> Extracting unbinned light curve ad50006000s100602h_1.ulc
** XSELECT V1.3 **
!> Enter session name >[xsel] xsel
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS S1CCDPOW
1 W50 EAST BRIGHT HIGH 28/04/93 22:52:12 0.14E+04 1095 1111
EXTRACTOR vers 2.0 11 Apr 1997.
Doing file: /data/data17/seq_proc/50006000.007/ad50006000s100602h.evt
Total Good Bad: Region Time Phase Cut
1095 733 362 0 0 0
Writing events file
733 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
1095 733 362 0 0 0
in 1421.93 seconds
Command not found; type ? for a command listing
!xsel:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!xsel:ASCA > set datadir .
Setting data directory to /data/data17/seq_proc/50006000.007/
Setting mkf directory to /data/data17/seq_proc/50006000.007/
!xsel:ASCA > read events ad50006000s100602h.evt
Got new instrument: SIS1
Setting: IMAGE binning = 4
WMAP binning = 8
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 2047
Got the minimum time resolution of the read data: 16.000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data17/seq_proc/50006000.007/
HK Directory is: /data/data17/seq_proc/50006000.007/
!xsel:ASCA-SIS1-BRIGHT > filter region ad50006000s132002_1.reg
!xsel:ASCA-SIS1-BRIGHT > extract events
!xsel:ASCA-SIS1-BRIGHT > save events outfile=ad50006000s100602h_1.ulc use_events=yes
Wrote events list to file ad50006000s100602h_1.ulc
Changing Data directory from:
/data/data17/seq_proc/50006000.007/
to the current working directory.
!xsel:ASCA-SIS1-BRIGHT > exit save_session=no
-> Extracting unbinned light curve ad50006000s100612h_1.ulc
** XSELECT V1.3 **
!> Enter session name >[xsel] xsel
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS S1CCDPOW
1 W50 EAST BRIGHT2 HIGH 28/04/93 22:52:12 0.14E+04 1111 1111
EXTRACTOR vers 2.0 11 Apr 1997.
Doing file: /data/data17/seq_proc/50006000.007/ad50006000s100612h.evt
Total Good Bad: Region Time Phase Cut
1111 740 371 0 0 0
Writing events file
740 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
1111 740 371 0 0 0
in 1421.93 seconds
Command not found; type ? for a command listing
!xsel:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!xsel:ASCA > set datadir .
Setting data directory to /data/data17/seq_proc/50006000.007/
Setting mkf directory to /data/data17/seq_proc/50006000.007/
!xsel:ASCA > read events ad50006000s100612h.evt
Got new instrument: SIS1
Setting: IMAGE binning = 4
WMAP binning = 8
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 4095
Got the minimum time resolution of the read data: 16.000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data17/seq_proc/50006000.007/
HK Directory is: /data/data17/seq_proc/50006000.007/
!xsel:ASCA-SIS1-BRIGHT2 > filter region ad50006000s132002_1.reg
!xsel:ASCA-SIS1-BRIGHT2 > extract events
!xsel:ASCA-SIS1-BRIGHT2 > save events outfile=ad50006000s100612h_1.ulc use_events=yes
Wrote events list to file ad50006000s100612h_1.ulc
Changing Data directory from:
/data/data17/seq_proc/50006000.007/
to the current working directory.
!xsel:ASCA-SIS1-BRIGHT2 > exit save_session=no
*** tlmFrm Version 1.1 (1997-08-25) *** total number of superframes: 15310 Total of 0 sets of frame data are extracted.-> Extracting frame mode data from ft930428_1949.2350
*** tlmFrm Version 1.1 (1997-08-25) *** total number of superframes: 1573 Total of 0 sets of frame data are extracted.
1 ad50006000g200170m.unf 178566 1 ad50006000g200270h.unf 178566 1 ad50006000g200370l.unf 178566 1 ad50006000g200470m.unf 178566 1 ad50006000g200570h.unf 178566-> Fetching GIS2_CALSRC256.2
** XSELECT V1.3 **
!> Enter session name >[xsel] xsel
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS PHA_BINS
1 W50 EAST PH MEDIUM 27/04/93 23:50:48 0.27E+05 82925 1024
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS PHA_BINS
1 W50 EAST PH MEDIUM 27/04/93 23:50:48 0.27E+05 82925 1024
2 W50 EAST PH HIGH 28/04/93 03:44:46 0.24E+05 60324 1024
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS PHA_BINS
1 W50 EAST PH MEDIUM 27/04/93 23:50:48 0.27E+05 82925 1024
2 W50 EAST PH HIGH 28/04/93 03:44:46 0.24E+05 60324 1024
3 W50 EAST PH LOW 28/04/93 01:05:28 0.18E+04 4648 1024
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS PHA_BINS
1 W50 EAST PH MEDIUM 27/04/93 23:50:48 0.27E+05 82925 1024
2 W50 EAST PH HIGH 28/04/93 03:44:46 0.24E+05 60324 1024
3 W50 EAST PH LOW 28/04/93 01:05:28 0.18E+04 4648 1024
4 W50 EAST PH MEDIUM 28/04/93 19:50:32 0.99E+04 26977 1024
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS PHA_BINS
1 W50 EAST PH MEDIUM 27/04/93 23:50:48 0.27E+05 82925 1024
2 W50 EAST PH HIGH 28/04/93 03:44:46 0.24E+05 60324 1024
3 W50 EAST PH LOW 28/04/93 01:05:28 0.18E+04 4648 1024
4 W50 EAST PH MEDIUM 28/04/93 19:50:32 0.99E+04 26977 1024
5 W50 EAST PH HIGH 28/04/93 22:52:30 0.15E+04 3692 1024
EXTRACTOR vers 2.0 11 Apr 1997.
Getting FITS WCS Keywords
Doing file: /data/data17/seq_proc/50006000.007/ad50006000g200170m.unf
Total Good Bad: Region Time Phase Cut
82925 14491 68434 0 0 0
Doing file: /data/data17/seq_proc/50006000.007/ad50006000g200270h.unf
Total Good Bad: Region Time Phase Cut
60324 11682 48642 0 0 0
Doing file: /data/data17/seq_proc/50006000.007/ad50006000g200370l.unf
Total Good Bad: Region Time Phase Cut
4648 884 3764 0 0 0
Doing file: /data/data17/seq_proc/50006000.007/ad50006000g200470m.unf
Total Good Bad: Region Time Phase Cut
26977 4990 21987 0 0 0
Doing file: /data/data17/seq_proc/50006000.007/ad50006000g200570h.unf
Total Good Bad: Region Time Phase Cut
3692 694 2998 0 0 0
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
178566 32741 145825 0 0 0
in 64841.80 seconds
Spectrum has 32741 counts for 0.5049 counts/sec
-------------------------
MANDATORY KEYWORDS/VALUES
-------------------------
--------------------------------------------------------------------
--------------------------------------------------------------------
EXTNAME - SPECTRUM Name of this BINTABLE
TELESCOP - ASCA Mission/Satellite name
INSTRUME - GIS2 Instrument/Detector
FILTER - Instrument filter in use
EXPOSURE - 64842. Integration time (in secs) of PHA data
AREASCAL - 1.0000 Area scaling factor
BACKSCAL - 3.57971E-02 Background scaling factor
BACKFILE - NONE Associated background file
CORRSCAL - 1.0000 Correlation scaling factor
CORRFILE - none Associated correlation file
RESPFILE - NONE Associated redistribution matrix file
ANCRFILE - none Associated ancillary response file
XFLT0001 - none XSPEC selection filter
POISSERR - TRUE Whether Poissonian errors apply
CHANTYPE - PI Whether channels have been corrected
TLMIN1 - 0 First legal Detector channel
DETCHANS - 1024 No. of legal detector channels
NCHAN - 1024 No. of detector channels in dataset
PHAVERSN - 1992a OGIP FITS version number
STAT_ERR - FALSE Statistical Error
SYS_ERR - TRUE Fractional Systematic Error
QUALITY - TRUE Quality Flag
GROUPING - FALSE Grouping Flag
--------------------------------------------------------------------
--------------------------------------------------------------------
...
... --------
... GROUPING
... --------
... ---------------------------------------------
... Channel Grouping (Channel-Channel) :
... ---------------------------------------------
...
...... exiting, changes written to file : ad50006000g220170.cal
Command not found; type ? for a command listing
!xsel:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!xsel:ASCA > set datadir .
Setting data directory to /data/data17/seq_proc/50006000.007/
Setting mkf directory to /data/data17/seq_proc/50006000.007/
!xsel:ASCA > read events ad50006000g200170m.unf
Got new instrument: GIS2
Setting: IMAGE binning = 1
WMAP binning = 1
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 1023
Got the minimum time resolution of the read data: 0.50000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data17/seq_proc/50006000.007/
HK Directory is: /data/data17/seq_proc/50006000.007/
!xsel:ASCA-GIS2-PH > read events ad50006000g200270h.unf
Getting Min and Max for Energy Column...
Got min and max for PI: 0 1023
Got the minimum time resolution of the read data: 0.62500E-01
Number of files read in: 2
******************** Observation Catalogue ********************
Data Directory is: /data/data17/seq_proc/50006000.007/
HK Directory is: /data/data17/seq_proc/50006000.007/
!xsel:ASCA-GIS2-PH > read events ad50006000g200370l.unf
Getting Min and Max for Energy Column...
Got min and max for PI: 0 1023
Got the minimum time resolution of the read data: 2.0000
Number of files read in: 3
******************** Observation Catalogue ********************
Data Directory is: /data/data17/seq_proc/50006000.007/
HK Directory is: /data/data17/seq_proc/50006000.007/
!xsel:ASCA-GIS2-PH > read events ad50006000g200470m.unf
Getting Min and Max for Energy Column...
Got min and max for PI: 0 1023
Got the minimum time resolution of the read data: 0.50000
Number of files read in: 4
******************** Observation Catalogue ********************
Data Directory is: /data/data17/seq_proc/50006000.007/
HK Directory is: /data/data17/seq_proc/50006000.007/
!xsel:ASCA-GIS2-PH > read events ad50006000g200570h.unf
Getting Min and Max for Energy Column...
Got min and max for PI: 0 1023
Got the minimum time resolution of the read data: 0.62500E-01
Number of files read in: 5
******************** Observation Catalogue ********************
Data Directory is: /data/data17/seq_proc/50006000.007/
HK Directory is: /data/data17/seq_proc/50006000.007/
!xsel:ASCA-GIS2-PH > filter region GIS2_CALSRC256.2
!xsel:ASCA-GIS2-PH > extract spectrum
!xsel:ASCA-GIS2-PH > save spectrum ad50006000g220170.cal group=yes
Wrote spectrum to ad50006000g220170.cal
!xsel:ASCA-GIS2-PH > exit save_session=no
-> gis2v4_0.rmf already present in current directory
XSPEC 9.01 17:24:06 18-Mar-98
Plot device not set, use "cpd" to set it
Type "help" or "?" for further information
!XSPEC> query yes
Querying disabled - assuming answer is yes
!XSPEC> data ad50006000g220170.cal
Net count rate (cts/s) for file 1 0.5049 +/- 2.7907E-03
1 data set is in use
!XSPEC> ignore bad
!XSPEC> ignore **-4.0
!XSPEC> ignore 8.0-**
!XSPEC> model const/b + gauss/b + gauss/b
Background components must be from the additive model list
mo = constant[1] ) + gaussian/b[2] + gaussian/b[3]
Input parameter value, delta, min, bot, top, and max values for ...
Mod parameter 1 of component 1 constant factor
1.000 1.0000E-02 0. 0. 1.0000E+10 1.0000E+10
!
Mod parameter 2 of component 2 gaussian LineE
6.500 5.0000E-02 0. 0. 1.0000E+06 1.0000E+06
! 5.9
Mod parameter 3 of component 2 gaussian Sigma
0.1000 5.0000E-02 0. 0. 10.00 20.00
! 0.0
Mod parameter 4 of component 2 gaussian norm
1.000 1.0000E-02 0. 0. 1.0000E+24 1.0000E+24
!
Mod parameter 5 of component 3 gaussian LineE
6.500 5.0000E-02 0. 0. 1.0000E+06 1.0000E+06
! 6.5
Mod parameter 6 of component 3 gaussian Sigma
0.1000 5.0000E-02 0. 0. 10.00 20.00
! 0.0
Mod parameter 7 of component 3 gaussian norm
1.000 1.0000E-02 0. 0. 1.0000E+24 1.0000E+24
!
---------------------------------------------------------------------------
---------------------------------------------------------------------------
mo = constant[1] ) + gaussian/b[2] + gaussian/b[3]
Model Fit Model Component Parameter Value
par par comp
1 1 1 constant factor 1.00000 +/- 0.
2 2 2 gaussian/b LineE 5.90000 +/- 0.
3 3 2 gaussian/b Sigma 0. +/- 0.
4 4 2 gaussian/b norm 1.00000 +/- 0.
5 5 3 gaussian/b LineE 6.50000 +/- 0.
6 6 3 gaussian/b Sigma 0. +/- 0.
7 7 3 gaussian/b norm 1.00000 +/- 0.
---------------------------------------------------------------------------
---------------------------------------------------------------------------
7 variable fit parameters
Chi-Squared = 8.7603E+05 using 84 PHA bins.
Reduced chi-squared = 1.1377E+04
!XSPEC> newpar 5 = 2 1.101005
6 variable fit parameters
Chi-Squared = 8.6894E+05 using 84 PHA bins.
Reduced chi-squared = 1.1140E+04
!XSPEC> newpar 6 = 3 1.049288
5 variable fit parameters
Chi-Squared = 8.6894E+05 using 84 PHA bins.
Reduced chi-squared = 1.0999E+04
!XSPEC> renorm
Chi-Squared = 8854. using 84 PHA bins.
Reduced chi-squared = 112.1
!XSPEC> fit
Chi-Squared Lvl Fit param # 1 2 3 4
5
Due to zero model norms
fit parameter 1 is temporarily frozen
6938.3 0 1.000 5.892 0.1138 0.1276
0.1113
Due to zero model norms
fit parameter 1 is temporarily frozen
2642.2 0 1.000 5.857 0.1710 0.1960
9.8523E-02
Due to zero model norms
fit parameter 1 is temporarily frozen
1157.6 -1 1.000 5.896 0.1979 0.2788
6.7118E-02
Due to zero model norms
fit parameter 1 is temporarily frozen
1065.3 -2 1.000 5.933 0.2193 0.3103
4.4157E-02
Due to zero model norms
fit parameter 1 is temporarily frozen
1051.6 -3 1.000 5.916 0.2062 0.3009
5.3359E-02
Due to zero model norms
fit parameter 1 is temporarily frozen
1050.0 -4 1.000 5.923 0.2107 0.3051
4.9052E-02
Due to zero model norms
fit parameter 1 is temporarily frozen
1049.2 -5 1.000 5.920 0.2082 0.3032
5.0990E-02
Due to zero model norms
fit parameter 1 is temporarily frozen
1049.1 -1 1.000 5.921 0.2087 0.3037
5.0478E-02
Due to zero model norms
fit parameter 1 is temporarily frozen
1049.1 1 1.000 5.921 0.2087 0.3037
5.0478E-02
---------------------------------------------------------------------------
---------------------------------------------------------------------------
mo = constant[1] ) + gaussian/b[2] + gaussian/b[3]
Model Fit Model Component Parameter Value
par par comp
1 1 1 constant factor 1.00000 +/- -1.0000
2 2 2 gaussian/b LineE 5.92082 +/- 0.38866E-02
3 3 2 gaussian/b Sigma 0.208682 +/- 0.39251E-02
4 4 2 gaussian/b norm 0.303662 +/- 0.30093E-02
5 2 3 gaussian/b LineE 6.51885 = par 2 * 1.1010
6 3 3 gaussian/b Sigma 0.218967 = par 3 * 1.0493
7 5 3 gaussian/b norm 5.047768E-02 +/- 0.22410E-02
---------------------------------------------------------------------------
---------------------------------------------------------------------------
Chi-Squared = 1049. using 84 PHA bins.
Reduced chi-squared = 13.28
!XSPEC> setplot energy
!XSPEC> iplot data
!PLT> label top GIS2 Calibration Source, should peak near 5.9 keV
!PLT> log x off
!PLT> rescale x 4 8
!PLT> hard /ps
!PLT> quit
!XSPEC> exit
!Do you really want to exit (y) y
XSPEC: quit
-> Calibration source ad50006000g220170.cal peaks at 5.92082 +/- 0.0038866 keV1 ad50006000g300170m.unf 171549 1 ad50006000g300270h.unf 171549 1 ad50006000g300370l.unf 171549 1 ad50006000g300470m.unf 171549 1 ad50006000g300570h.unf 171549-> Fetching GIS3_CALSRC256.2
** XSELECT V1.3 **
!> Enter session name >[xsel] xsel
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS PHA_BINS
1 W50 EAST PH MEDIUM 27/04/93 23:50:48 0.27E+05 79675 1024
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS PHA_BINS
1 W50 EAST PH MEDIUM 27/04/93 23:50:48 0.27E+05 79675 1024
2 W50 EAST PH HIGH 28/04/93 03:44:46 0.24E+05 57073 1024
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS PHA_BINS
1 W50 EAST PH MEDIUM 27/04/93 23:50:48 0.27E+05 79675 1024
2 W50 EAST PH HIGH 28/04/93 03:44:46 0.24E+05 57073 1024
3 W50 EAST PH LOW 28/04/93 01:05:28 0.18E+04 4709 1024
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS PHA_BINS
1 W50 EAST PH MEDIUM 27/04/93 23:50:48 0.27E+05 79675 1024
2 W50 EAST PH HIGH 28/04/93 03:44:46 0.24E+05 57073 1024
3 W50 EAST PH LOW 28/04/93 01:05:28 0.18E+04 4709 1024
4 W50 EAST PH MEDIUM 28/04/93 19:50:32 0.99E+04 26610 1024
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS PHA_BINS
1 W50 EAST PH MEDIUM 27/04/93 23:50:48 0.27E+05 79675 1024
2 W50 EAST PH HIGH 28/04/93 03:44:46 0.24E+05 57073 1024
3 W50 EAST PH LOW 28/04/93 01:05:28 0.18E+04 4709 1024
4 W50 EAST PH MEDIUM 28/04/93 19:50:32 0.99E+04 26610 1024
5 W50 EAST PH HIGH 28/04/93 22:52:30 0.15E+04 3482 1024
EXTRACTOR vers 2.0 11 Apr 1997.
Getting FITS WCS Keywords
Doing file: /data/data17/seq_proc/50006000.007/ad50006000g300170m.unf
Total Good Bad: Region Time Phase Cut
79675 13103 66572 0 0 0
Doing file: /data/data17/seq_proc/50006000.007/ad50006000g300270h.unf
Total Good Bad: Region Time Phase Cut
57073 10873 46200 0 0 0
Doing file: /data/data17/seq_proc/50006000.007/ad50006000g300370l.unf
Total Good Bad: Region Time Phase Cut
4709 855 3854 0 0 0
Doing file: /data/data17/seq_proc/50006000.007/ad50006000g300470m.unf
Total Good Bad: Region Time Phase Cut
26610 4562 22048 0 0 0
Doing file: /data/data17/seq_proc/50006000.007/ad50006000g300570h.unf
Total Good Bad: Region Time Phase Cut
3482 659 2823 0 0 0
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
171549 30052 141497 0 0 0
in 64819.80 seconds
Spectrum has 30052 counts for 0.4636 counts/sec
-------------------------
MANDATORY KEYWORDS/VALUES
-------------------------
--------------------------------------------------------------------
--------------------------------------------------------------------
EXTNAME - SPECTRUM Name of this BINTABLE
TELESCOP - ASCA Mission/Satellite name
INSTRUME - GIS3 Instrument/Detector
FILTER - Instrument filter in use
EXPOSURE - 64820. Integration time (in secs) of PHA data
AREASCAL - 1.0000 Area scaling factor
BACKSCAL - 2.83356E-02 Background scaling factor
BACKFILE - NONE Associated background file
CORRSCAL - 1.0000 Correlation scaling factor
CORRFILE - none Associated correlation file
RESPFILE - NONE Associated redistribution matrix file
ANCRFILE - none Associated ancillary response file
XFLT0001 - none XSPEC selection filter
POISSERR - TRUE Whether Poissonian errors apply
CHANTYPE - PI Whether channels have been corrected
TLMIN1 - 0 First legal Detector channel
DETCHANS - 1024 No. of legal detector channels
NCHAN - 1024 No. of detector channels in dataset
PHAVERSN - 1992a OGIP FITS version number
STAT_ERR - FALSE Statistical Error
SYS_ERR - TRUE Fractional Systematic Error
QUALITY - TRUE Quality Flag
GROUPING - FALSE Grouping Flag
--------------------------------------------------------------------
--------------------------------------------------------------------
...
... --------
... GROUPING
... --------
... ---------------------------------------------
... Channel Grouping (Channel-Channel) :
... ---------------------------------------------
...
...... exiting, changes written to file : ad50006000g320170.cal
Command not found; type ? for a command listing
!xsel:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!xsel:ASCA > set datadir .
Setting data directory to /data/data17/seq_proc/50006000.007/
Setting mkf directory to /data/data17/seq_proc/50006000.007/
!xsel:ASCA > read events ad50006000g300170m.unf
Got new instrument: GIS3
Setting: IMAGE binning = 1
WMAP binning = 1
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 1023
Got the minimum time resolution of the read data: 0.50000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data17/seq_proc/50006000.007/
HK Directory is: /data/data17/seq_proc/50006000.007/
!xsel:ASCA-GIS3-PH > read events ad50006000g300270h.unf
Getting Min and Max for Energy Column...
Got min and max for PI: 0 1023
Got the minimum time resolution of the read data: 0.62500E-01
Number of files read in: 2
******************** Observation Catalogue ********************
Data Directory is: /data/data17/seq_proc/50006000.007/
HK Directory is: /data/data17/seq_proc/50006000.007/
!xsel:ASCA-GIS3-PH > read events ad50006000g300370l.unf
Getting Min and Max for Energy Column...
Got min and max for PI: 0 1023
Got the minimum time resolution of the read data: 2.0000
Number of files read in: 3
******************** Observation Catalogue ********************
Data Directory is: /data/data17/seq_proc/50006000.007/
HK Directory is: /data/data17/seq_proc/50006000.007/
!xsel:ASCA-GIS3-PH > read events ad50006000g300470m.unf
Getting Min and Max for Energy Column...
Got min and max for PI: 0 1023
Got the minimum time resolution of the read data: 0.50000
Number of files read in: 4
******************** Observation Catalogue ********************
Data Directory is: /data/data17/seq_proc/50006000.007/
HK Directory is: /data/data17/seq_proc/50006000.007/
!xsel:ASCA-GIS3-PH > read events ad50006000g300570h.unf
Getting Min and Max for Energy Column...
Got min and max for PI: 0 1023
Got the minimum time resolution of the read data: 0.62500E-01
Number of files read in: 5
******************** Observation Catalogue ********************
Data Directory is: /data/data17/seq_proc/50006000.007/
HK Directory is: /data/data17/seq_proc/50006000.007/
!xsel:ASCA-GIS3-PH > filter region GIS3_CALSRC256.2
!xsel:ASCA-GIS3-PH > extract spectrum
!xsel:ASCA-GIS3-PH > save spectrum ad50006000g320170.cal group=yes
Wrote spectrum to ad50006000g320170.cal
!xsel:ASCA-GIS3-PH > exit save_session=no
-> gis3v4_0.rmf already present in current directory
XSPEC 9.01 17:26:29 18-Mar-98
Plot device not set, use "cpd" to set it
Type "help" or "?" for further information
!XSPEC> query yes
Querying disabled - assuming answer is yes
!XSPEC> data ad50006000g320170.cal
Net count rate (cts/s) for file 1 0.4636 +/- 2.6746E-03
1 data set is in use
!XSPEC> ignore bad
!XSPEC> ignore **-4.0
!XSPEC> ignore 8.0-**
!XSPEC> model const/b + gauss/b + gauss/b
Background components must be from the additive model list
mo = constant[1] ) + gaussian/b[2] + gaussian/b[3]
Input parameter value, delta, min, bot, top, and max values for ...
Mod parameter 1 of component 1 constant factor
1.000 1.0000E-02 0. 0. 1.0000E+10 1.0000E+10
!
Mod parameter 2 of component 2 gaussian LineE
6.500 5.0000E-02 0. 0. 1.0000E+06 1.0000E+06
! 5.9
Mod parameter 3 of component 2 gaussian Sigma
0.1000 5.0000E-02 0. 0. 10.00 20.00
! 0.0
Mod parameter 4 of component 2 gaussian norm
1.000 1.0000E-02 0. 0. 1.0000E+24 1.0000E+24
!
Mod parameter 5 of component 3 gaussian LineE
6.500 5.0000E-02 0. 0. 1.0000E+06 1.0000E+06
! 6.5
Mod parameter 6 of component 3 gaussian Sigma
0.1000 5.0000E-02 0. 0. 10.00 20.00
! 0.0
Mod parameter 7 of component 3 gaussian norm
1.000 1.0000E-02 0. 0. 1.0000E+24 1.0000E+24
!
---------------------------------------------------------------------------
---------------------------------------------------------------------------
mo = constant[1] ) + gaussian/b[2] + gaussian/b[3]
Model Fit Model Component Parameter Value
par par comp
1 1 1 constant factor 1.00000 +/- 0.
2 2 2 gaussian/b LineE 5.90000 +/- 0.
3 3 2 gaussian/b Sigma 0. +/- 0.
4 4 2 gaussian/b norm 1.00000 +/- 0.
5 5 3 gaussian/b LineE 6.50000 +/- 0.
6 6 3 gaussian/b Sigma 0. +/- 0.
7 7 3 gaussian/b norm 1.00000 +/- 0.
---------------------------------------------------------------------------
---------------------------------------------------------------------------
7 variable fit parameters
Chi-Squared = 8.7117E+05 using 84 PHA bins.
Reduced chi-squared = 1.1314E+04
!XSPEC> newpar 5 = 2 1.101005
6 variable fit parameters
Chi-Squared = 8.6419E+05 using 84 PHA bins.
Reduced chi-squared = 1.1079E+04
!XSPEC> newpar 6 = 3 1.049288
5 variable fit parameters
Chi-Squared = 8.6419E+05 using 84 PHA bins.
Reduced chi-squared = 1.0939E+04
!XSPEC> renorm
Chi-Squared = 7502. using 84 PHA bins.
Reduced chi-squared = 94.96
!XSPEC> fit
Chi-Squared Lvl Fit param # 1 2 3 4
5
Due to zero model norms
fit parameter 1 is temporarily frozen
5857.4 0 1.000 5.894 0.1091 0.1263
0.1118
Due to zero model norms
fit parameter 1 is temporarily frozen
2802.3 0 1.000 5.874 0.1561 0.1830
9.8399E-02
Due to zero model norms
fit parameter 1 is temporarily frozen
1138.8 -1 1.000 5.942 0.1773 0.2593
6.2247E-02
Due to zero model norms
fit parameter 1 is temporarily frozen
943.25 -2 1.000 5.986 0.1922 0.2966
3.8996E-02
Due to zero model norms
fit parameter 1 is temporarily frozen
914.76 -3 1.000 5.968 0.1755 0.2876
4.7899E-02
Due to zero model norms
fit parameter 1 is temporarily frozen
912.28 -4 1.000 5.973 0.1785 0.2907
4.4658E-02
Due to zero model norms
fit parameter 1 is temporarily frozen
911.65 -5 1.000 5.972 0.1768 0.2897
4.5697E-02
Due to zero model norms
fit parameter 1 is temporarily frozen
911.65 -1 1.000 5.972 0.1770 0.2899
4.5474E-02
---------------------------------------------------------------------------
---------------------------------------------------------------------------
mo = constant[1] ) + gaussian/b[2] + gaussian/b[3]
Model Fit Model Component Parameter Value
par par comp
1 1 1 constant factor 1.00000 +/- -1.0000
2 2 2 gaussian/b LineE 5.97192 +/- 0.32132E-02
3 3 2 gaussian/b Sigma 0.176983 +/- 0.36510E-02
4 4 2 gaussian/b norm 0.289909 +/- 0.26310E-02
5 2 3 gaussian/b LineE 6.57512 = par 2 * 1.1010
6 3 3 gaussian/b Sigma 0.185706 = par 3 * 1.0493
7 5 3 gaussian/b norm 4.547400E-02 +/- 0.17403E-02
---------------------------------------------------------------------------
---------------------------------------------------------------------------
Chi-Squared = 911.6 using 84 PHA bins.
Reduced chi-squared = 11.54
!XSPEC> setplot energy
!XSPEC> iplot data
!PLT> label top GIS3 Calibration Source, should peak near 5.9 keV
!PLT> log x off
!PLT> rescale x 4 8
!PLT> hard /ps
!PLT> quit
!XSPEC> exit
!Do you really want to exit (y) y
XSPEC: quit
-> Calibration source ad50006000g320170.cal peaks at 5.97192 +/- 0.0032132 keV
** XSELECT V1.3 **
!> Enter session name >[xsel] earthevents
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS S0CCDPOW
1 W50 EAST BRIGHT HIGH 28/04/93 03:44:28 0.22E+05 152479 1111
EXTRACTOR vers 2.0 11 Apr 1997.
Doing file: /data/data17/seq_proc/50006000.007/ad50006000s000102h.unf
Total Good Bad: Region Time Phase Cut
152479 23567 0 128912 0 0
Writing events file
23567 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
152479 23567 0 128912 0 0
in 3684.60 seconds
Command not found; type ? for a command listing
!earthevents:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!earthevents:ASCA > set datadir .
Setting data directory to /data/data17/seq_proc/50006000.007/
Setting mkf directory to /data/data17/seq_proc/50006000.007/
!earthevents:ASCA > read events ad50006000s000102h.unf
Got new instrument: SIS0
Setting: IMAGE binning = 4
WMAP binning = 8
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 2047
Got the minimum time resolution of the read data: 16.000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data17/seq_proc/50006000.007/
HK Directory is: /data/data17/seq_proc/50006000.007/
!earthevents:ASCA-SIS0-BRIGHT > select mkf "FOV==1" data_dir=. ASCA_mkf_def_expr=ft*.mkf
!earthevents:ASCA-SIS0-BRIGHT > extract events
!earthevents:ASCA-SIS0-BRIGHT > save events outfile=event.tmp use_events=no
Wrote events list to file event.tmp
!earthevents:ASCA-SIS0-BRIGHT > exit save_session=no
-> Cleaning hot pixels from ad50006000s000102h.unf
CLEANSIS_V1.6
allocating image arrays...
PROGRAM TO MAKE AN SIS SCIENCE FILE CLEANED OF ANOMALOUS PIXELS.
* Anomalous pixels may consist of at least two populations.
1. Persistent HOT pixels are removed by comparing to the chip mean.
2. Flickering WARM pixels are removed by comparing to the cell mean.
3. In faint areas (zero bgd), flickering pixels are removed with a
cutoff threshold.
Hints:
Choose cell size and thresholds based on the expected background and the PSF.
Use the DIRTYSIS option to examine the anomalous pixel spectra.
Try a multiple pass clean:
Choose a PHA cut to optimize the S/N of the flickering pixels,
then a broad band clean.
Be suspicious of extended source cleans.
For very bright sources you may need to turn off the iteration option.
See the help page for further info (fhelp cleansis)
Poisson clean cell size : 5
Poisson probability threshold : 0.575E-05
Zero Bgd Cutoff threshold (>) : 3
Iterate : F
Dirtysis : F
Minimum PHA value (inclusive) : 0
Maximum PHA value (inclusive) : 4095
open output file: ad50006000s000102h.drk
reading data file: event.tmp
copying primary header to output file...
making chip image...
Total counts in chip images : 23567
copy bad pix array...
cleaning chip # 0
Hot pixels & counts : 72 14370
Flickering pixels iter, pixels & cnts : 1 33 634
cleaning chip # 1
Hot pixels & counts : 18 2622
Flickering pixels iter, pixels & cnts : 1 192 934
cleaning chip # 2
Hot pixels & counts : 22 1508
Flickering pixels iter, pixels & cnts : 1 15 94
cleaning chip # 3
Hot pixels & counts : 24 2080
Flickering pixels iter, pixels & cnts : 1 12 86
Number of pixels rejected : 388
Number of (internal) image counts : 23567
Number of image cts rejected (N, %) : 22328 94.7426453
By chip : 0 1 2 3
Pixels rejected : 105 210 37 36
Image counts : 15223 4101 1847 2396
Image cts rejected: 15004 3556 1602 2166
Image cts rej (%) : 98.56 86.71 86.74 90.40
filtering data...
Total counts : 15223 4101 1847 2396
Total cts rejected: 15004 3556 1602 2166
Total cts rej (%) : 98.56 86.71 86.74 90.40
Number of clean counts accepted : 1239
writing history cards...
copying extensions...
writing out hot pixs...
Number of rejected pixels : 388
updating NEVENTS keywords...
closing data file...
closing clean file...
-> Extracting bright and dark Earth events from ad50006000s000112h.unf
** XSELECT V1.3 **
!> Enter session name >[xsel] earthevents
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS S0CCDPOW
1 W50 EAST BRIGHT2 HIGH 28/04/93 03:44:28 0.22E+05 159300 1111
EXTRACTOR vers 2.0 11 Apr 1997.
Doing file: /data/data17/seq_proc/50006000.007/ad50006000s000112h.unf
Total Good Bad: Region Time Phase Cut
159300 24536 0 134764 0 0
Writing events file
24536 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
159300 24536 0 134764 0 0
in 3684.60 seconds
Command not found; type ? for a command listing
!earthevents:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!earthevents:ASCA > set datadir .
Setting data directory to /data/data17/seq_proc/50006000.007/
Setting mkf directory to /data/data17/seq_proc/50006000.007/
!earthevents:ASCA > read events ad50006000s000112h.unf
Got new instrument: SIS0
Setting: IMAGE binning = 4
WMAP binning = 8
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 4095
Got the minimum time resolution of the read data: 16.000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data17/seq_proc/50006000.007/
HK Directory is: /data/data17/seq_proc/50006000.007/
!earthevents:ASCA-SIS0-BRIGHT2 > select mkf "FOV==1" data_dir=. ASCA_mkf_def_expr=ft*.mkf
!earthevents:ASCA-SIS0-BRIGHT2 > extract events
!earthevents:ASCA-SIS0-BRIGHT2 > save events outfile=event.tmp use_events=no
Wrote events list to file event.tmp
!earthevents:ASCA-SIS0-BRIGHT2 > exit save_session=no
-> Cleaning hot pixels from ad50006000s000112h.unf
CLEANSIS_V1.6
allocating image arrays...
PROGRAM TO MAKE AN SIS SCIENCE FILE CLEANED OF ANOMALOUS PIXELS.
* Anomalous pixels may consist of at least two populations.
1. Persistent HOT pixels are removed by comparing to the chip mean.
2. Flickering WARM pixels are removed by comparing to the cell mean.
3. In faint areas (zero bgd), flickering pixels are removed with a
cutoff threshold.
Hints:
Choose cell size and thresholds based on the expected background and the PSF.
Use the DIRTYSIS option to examine the anomalous pixel spectra.
Try a multiple pass clean:
Choose a PHA cut to optimize the S/N of the flickering pixels,
then a broad band clean.
Be suspicious of extended source cleans.
For very bright sources you may need to turn off the iteration option.
See the help page for further info (fhelp cleansis)
Poisson clean cell size : 5
Poisson probability threshold : 0.575E-05
Zero Bgd Cutoff threshold (>) : 3
Iterate : F
Dirtysis : F
Minimum PHA value (inclusive) : 0
Maximum PHA value (inclusive) : 4095
open output file: ad50006000s000112h.drk
reading data file: event.tmp
copying primary header to output file...
making chip image...
Total counts in chip images : 24536
copy bad pix array...
cleaning chip # 0
Hot pixels & counts : 73 14662
Flickering pixels iter, pixels & cnts : 1 33 642
cleaning chip # 1
Hot pixels & counts : 18 2624
Flickering pixels iter, pixels & cnts : 1 194 948
cleaning chip # 2
Hot pixels & counts : 21 1496
Flickering pixels iter, pixels & cnts : 1 16 108
cleaning chip # 3
Hot pixels & counts : 23 2074
Flickering pixels iter, pixels & cnts : 1 15 110
Number of pixels rejected : 393
Number of (internal) image counts : 24536
Number of image cts rejected (N, %) : 22664 92.3703918
By chip : 0 1 2 3
Pixels rejected : 106 212 37 38
Image counts : 15699 4264 2027 2546
Image cts rejected: 15304 3572 1604 2184
Image cts rej (%) : 97.48 83.77 79.13 85.78
filtering data...
Total counts : 15699 4264 2027 2546
Total cts rejected: 15304 3572 1604 2184
Total cts rej (%) : 97.48 83.77 79.13 85.78
Number of clean counts accepted : 1872
writing history cards...
copying extensions...
writing out hot pixs...
Number of rejected pixels : 393
updating NEVENTS keywords...
closing data file...
closing clean file...
-> Extracting bright and dark Earth events from ad50006000s000202m.unf
** XSELECT V1.3 **
!> Enter session name >[xsel] earthevents
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS S0CCDPOW
1 W50 EAST BRIGHT MEDIUM 27/04/93 23:50:32 0.32E+05 168750 1111
EXTRACTOR vers 2.0 11 Apr 1997.
Doing file: /data/data17/seq_proc/50006000.007/ad50006000s000202m.unf
Total Good Bad: Region Time Phase Cut
168750 40952 0 127798 0 0
Writing events file
40952 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
168750 40952 0 127798 0 0
in 6649.71 seconds
Command not found; type ? for a command listing
!earthevents:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!earthevents:ASCA > set datadir .
Setting data directory to /data/data17/seq_proc/50006000.007/
Setting mkf directory to /data/data17/seq_proc/50006000.007/
!earthevents:ASCA > read events ad50006000s000202m.unf
Got new instrument: SIS0
Setting: IMAGE binning = 4
WMAP binning = 8
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 2047
Got the minimum time resolution of the read data: 16.000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data17/seq_proc/50006000.007/
HK Directory is: /data/data17/seq_proc/50006000.007/
!earthevents:ASCA-SIS0-BRIGHT > select mkf "FOV==1" data_dir=. ASCA_mkf_def_expr=ft*.mkf
!earthevents:ASCA-SIS0-BRIGHT > extract events
!earthevents:ASCA-SIS0-BRIGHT > save events outfile=event.tmp use_events=no
Wrote events list to file event.tmp
!earthevents:ASCA-SIS0-BRIGHT > exit save_session=no
-> Cleaning hot pixels from ad50006000s000202m.unf
CLEANSIS_V1.6
allocating image arrays...
PROGRAM TO MAKE AN SIS SCIENCE FILE CLEANED OF ANOMALOUS PIXELS.
* Anomalous pixels may consist of at least two populations.
1. Persistent HOT pixels are removed by comparing to the chip mean.
2. Flickering WARM pixels are removed by comparing to the cell mean.
3. In faint areas (zero bgd), flickering pixels are removed with a
cutoff threshold.
Hints:
Choose cell size and thresholds based on the expected background and the PSF.
Use the DIRTYSIS option to examine the anomalous pixel spectra.
Try a multiple pass clean:
Choose a PHA cut to optimize the S/N of the flickering pixels,
then a broad band clean.
Be suspicious of extended source cleans.
For very bright sources you may need to turn off the iteration option.
See the help page for further info (fhelp cleansis)
Poisson clean cell size : 5
Poisson probability threshold : 0.575E-05
Zero Bgd Cutoff threshold (>) : 3
Iterate : F
Dirtysis : F
Minimum PHA value (inclusive) : 0
Maximum PHA value (inclusive) : 4095
open output file: ad50006000s000202m.drk
reading data file: event.tmp
copying primary header to output file...
making chip image...
Total counts in chip images : 40952
copy bad pix array...
cleaning chip # 0
Hot pixels & counts : 76 25811
Flickering pixels iter, pixels & cnts : 1 49 861
cleaning chip # 1
Hot pixels & counts : 20 4420
Flickering pixels iter, pixels & cnts : 1 33 318
cleaning chip # 2
Hot pixels & counts : 20 2453
Flickering pixels iter, pixels & cnts : 1 50 341
cleaning chip # 3
Hot pixels & counts : 27 3593
Flickering pixels iter, pixels & cnts : 1 28 173
Number of pixels rejected : 303
Number of (internal) image counts : 40952
Number of image cts rejected (N, %) : 37970 92.7183075
By chip : 0 1 2 3
Pixels rejected : 125 53 70 55
Image counts : 27420 5509 3590 4433
Image cts rejected: 26672 4738 2794 3766
Image cts rej (%) : 97.27 86.00 77.83 84.95
filtering data...
Total counts : 27420 5509 3590 4433
Total cts rejected: 26672 4738 2794 3766
Total cts rej (%) : 97.27 86.00 77.83 84.95
Number of clean counts accepted : 2982
writing history cards...
copying extensions...
writing out hot pixs...
Number of rejected pixels : 303
updating NEVENTS keywords...
closing data file...
closing clean file...
-> Extracting bright and dark Earth events from ad50006000s000302h.unf
** XSELECT V1.3 **
!> Enter session name >[xsel] earthevents
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS S0CCDPOW
1 W50 EAST BRIGHT HIGH 28/04/93 14:34:00 0.21E+04 14123 1011
EXTRACTOR vers 2.0 11 Apr 1997.
Skipping file: /data/data17/seq_proc/50006000.007/ad50006000s000302h.unf
Writing events file
0 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
0 0 0 0 0 0
in 0.00 seconds
Command not found; type ? for a command listing
!earthevents:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!earthevents:ASCA > set datadir .
Setting data directory to /data/data17/seq_proc/50006000.007/
Setting mkf directory to /data/data17/seq_proc/50006000.007/
!earthevents:ASCA > read events ad50006000s000302h.unf
Got new instrument: SIS0
Setting: IMAGE binning = 4
WMAP binning = 8
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 2047
Got the minimum time resolution of the read data: 16.000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data17/seq_proc/50006000.007/
HK Directory is: /data/data17/seq_proc/50006000.007/
!earthevents:ASCA-SIS0-BRIGHT > select mkf "FOV==1" data_dir=. ASCA_mkf_def_expr=ft*.mkf
!earthevents:ASCA-SIS0-BRIGHT > extract events
!earthevents:ASCA-SIS0-BRIGHT > save events outfile=event.tmp use_events=no
Wrote events list to file event.tmp
!earthevents:ASCA-SIS0-BRIGHT > exit save_session=no
-> Deleting ad50006000s000302h.drk since it contains 0 events
** XSELECT V1.3 **
!> Enter session name >[xsel] earthevents
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS S0CCDPOW
1 W50 EAST BRIGHT2 HIGH 28/04/93 14:34:00 0.21E+04 14737 1011
EXTRACTOR vers 2.0 11 Apr 1997.
Skipping file: /data/data17/seq_proc/50006000.007/ad50006000s000312h.unf
Writing events file
0 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
0 0 0 0 0 0
in 0.00 seconds
Command not found; type ? for a command listing
!earthevents:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!earthevents:ASCA > set datadir .
Setting data directory to /data/data17/seq_proc/50006000.007/
Setting mkf directory to /data/data17/seq_proc/50006000.007/
!earthevents:ASCA > read events ad50006000s000312h.unf
Got new instrument: SIS0
Setting: IMAGE binning = 4
WMAP binning = 8
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 4095
Got the minimum time resolution of the read data: 16.000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data17/seq_proc/50006000.007/
HK Directory is: /data/data17/seq_proc/50006000.007/
!earthevents:ASCA-SIS0-BRIGHT2 > select mkf "FOV==1" data_dir=. ASCA_mkf_def_expr=ft*.mkf
!earthevents:ASCA-SIS0-BRIGHT2 > extract events
!earthevents:ASCA-SIS0-BRIGHT2 > save events outfile=event.tmp use_events=no
Wrote events list to file event.tmp
!earthevents:ASCA-SIS0-BRIGHT2 > exit save_session=no
-> Deleting ad50006000s000312h.drk since it contains 0 events
** XSELECT V1.3 **
!> Enter session name >[xsel] earthevents
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS S0CCDPOW
1 W50 EAST BRIGHT LOW 28/04/93 01:05:12 0.18E+04 2859 1111
EXTRACTOR vers 2.0 11 Apr 1997.
Doing file: /data/data17/seq_proc/50006000.007/ad50006000s000402l.unf
Total Good Bad: Region Time Phase Cut
2859 2666 0 193 0 0
Writing events file
2666 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
2859 2666 0 193 0 0
in 684.98 seconds
Command not found; type ? for a command listing
!earthevents:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!earthevents:ASCA > set datadir .
Setting data directory to /data/data17/seq_proc/50006000.007/
Setting mkf directory to /data/data17/seq_proc/50006000.007/
!earthevents:ASCA > read events ad50006000s000402l.unf
Got new instrument: SIS0
Setting: IMAGE binning = 4
WMAP binning = 8
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 2047
Got the minimum time resolution of the read data: 16.000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data17/seq_proc/50006000.007/
HK Directory is: /data/data17/seq_proc/50006000.007/
!earthevents:ASCA-SIS0-BRIGHT > select mkf "FOV==1" data_dir=. ASCA_mkf_def_expr=ft*.mkf
!earthevents:ASCA-SIS0-BRIGHT > extract events
!earthevents:ASCA-SIS0-BRIGHT > save events outfile=event.tmp use_events=no
Wrote events list to file event.tmp
!earthevents:ASCA-SIS0-BRIGHT > exit save_session=no
-> Cleaning hot pixels from ad50006000s000402l.unf
CLEANSIS_V1.6
allocating image arrays...
PROGRAM TO MAKE AN SIS SCIENCE FILE CLEANED OF ANOMALOUS PIXELS.
* Anomalous pixels may consist of at least two populations.
1. Persistent HOT pixels are removed by comparing to the chip mean.
2. Flickering WARM pixels are removed by comparing to the cell mean.
3. In faint areas (zero bgd), flickering pixels are removed with a
cutoff threshold.
Hints:
Choose cell size and thresholds based on the expected background and the PSF.
Use the DIRTYSIS option to examine the anomalous pixel spectra.
Try a multiple pass clean:
Choose a PHA cut to optimize the S/N of the flickering pixels,
then a broad band clean.
Be suspicious of extended source cleans.
For very bright sources you may need to turn off the iteration option.
See the help page for further info (fhelp cleansis)
Poisson clean cell size : 5
Poisson probability threshold : 0.575E-05
Zero Bgd Cutoff threshold (>) : 3
Iterate : F
Dirtysis : F
Minimum PHA value (inclusive) : 0
Maximum PHA value (inclusive) : 4095
open output file: ad50006000s000402l.drk
reading data file: event.tmp
copying primary header to output file...
making chip image...
Total counts in chip images : 2666
copy bad pix array...
cleaning chip # 0
Hot pixels & counts : 34 1146
Flickering pixels iter, pixels & cnts : 1 23 153
cleaning chip # 1
Hot pixels & counts : 14 400
Flickering pixels iter, pixels & cnts : 1 4 16
cleaning chip # 2
Hot pixels & counts : 12 214
Flickering pixels iter, pixels & cnts : 1 1 3
cleaning chip # 3
Hot pixels & counts : 15 347
Flickering pixels iter, pixels & cnts : 1 9 38
Number of pixels rejected : 112
Number of (internal) image counts : 2666
Number of image cts rejected (N, %) : 2317 86.9092255
By chip : 0 1 2 3
Pixels rejected : 57 18 13 24
Image counts : 1376 499 322 469
Image cts rejected: 1299 416 217 385
Image cts rej (%) : 94.40 83.37 67.39 82.09
filtering data...
Total counts : 1376 499 322 469
Total cts rejected: 1299 416 217 385
Total cts rej (%) : 94.40 83.37 67.39 82.09
Number of clean counts accepted : 349
writing history cards...
copying extensions...
writing out hot pixs...
Number of rejected pixels : 112
updating NEVENTS keywords...
closing data file...
closing clean file...
-> Extracting bright and dark Earth events from ad50006000s000502m.unf
** XSELECT V1.3 **
!> Enter session name >[xsel] earthevents
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS S0CCDPOW
1 W50 EAST BRIGHT MEDIUM 28/04/93 19:50:16 0.12E+05 61343 1111
EXTRACTOR vers 2.0 11 Apr 1997.
Doing file: /data/data17/seq_proc/50006000.007/ad50006000s000502m.unf
Total Good Bad: Region Time Phase Cut
61343 9216 0 52127 0 0
Writing events file
9216 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
61343 9216 0 52127 0 0
in 1459.44 seconds
Command not found; type ? for a command listing
!earthevents:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!earthevents:ASCA > set datadir .
Setting data directory to /data/data17/seq_proc/50006000.007/
Setting mkf directory to /data/data17/seq_proc/50006000.007/
!earthevents:ASCA > read events ad50006000s000502m.unf
Got new instrument: SIS0
Setting: IMAGE binning = 4
WMAP binning = 8
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 2047
Got the minimum time resolution of the read data: 16.000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data17/seq_proc/50006000.007/
HK Directory is: /data/data17/seq_proc/50006000.007/
!earthevents:ASCA-SIS0-BRIGHT > select mkf "FOV==1" data_dir=. ASCA_mkf_def_expr=ft*.mkf
!earthevents:ASCA-SIS0-BRIGHT > extract events
!earthevents:ASCA-SIS0-BRIGHT > save events outfile=event.tmp use_events=no
Wrote events list to file event.tmp
!earthevents:ASCA-SIS0-BRIGHT > exit save_session=no
-> Cleaning hot pixels from ad50006000s000502m.unf
CLEANSIS_V1.6
allocating image arrays...
PROGRAM TO MAKE AN SIS SCIENCE FILE CLEANED OF ANOMALOUS PIXELS.
* Anomalous pixels may consist of at least two populations.
1. Persistent HOT pixels are removed by comparing to the chip mean.
2. Flickering WARM pixels are removed by comparing to the cell mean.
3. In faint areas (zero bgd), flickering pixels are removed with a
cutoff threshold.
Hints:
Choose cell size and thresholds based on the expected background and the PSF.
Use the DIRTYSIS option to examine the anomalous pixel spectra.
Try a multiple pass clean:
Choose a PHA cut to optimize the S/N of the flickering pixels,
then a broad band clean.
Be suspicious of extended source cleans.
For very bright sources you may need to turn off the iteration option.
See the help page for further info (fhelp cleansis)
Poisson clean cell size : 5
Poisson probability threshold : 0.575E-05
Zero Bgd Cutoff threshold (>) : 3
Iterate : F
Dirtysis : F
Minimum PHA value (inclusive) : 0
Maximum PHA value (inclusive) : 4095
open output file: ad50006000s000502m.drk
reading data file: event.tmp
copying primary header to output file...
making chip image...
Total counts in chip images : 9216
copy bad pix array...
cleaning chip # 0
Hot pixels & counts : 64 4906
Flickering pixels iter, pixels & cnts : 1 28 345
cleaning chip # 1
Hot pixels & counts : 19 876
Flickering pixels iter, pixels & cnts : 1 18 89
cleaning chip # 2
Hot pixels & counts : 16 552
Flickering pixels iter, pixels & cnts : 1 13 58
cleaning chip # 3
Hot pixels & counts : 14 613
Flickering pixels iter, pixels & cnts : 1 19 102
Number of pixels rejected : 191
Number of (internal) image counts : 9216
Number of image cts rejected (N, %) : 7541 81.8250885
By chip : 0 1 2 3
Pixels rejected : 92 37 29 33
Image counts : 5641 1430 1065 1080
Image cts rejected: 5251 965 610 715
Image cts rej (%) : 93.09 67.48 57.28 66.20
filtering data...
Total counts : 5641 1430 1065 1080
Total cts rejected: 5251 965 610 715
Total cts rej (%) : 93.09 67.48 57.28 66.20
Number of clean counts accepted : 1675
writing history cards...
copying extensions...
writing out hot pixs...
Number of rejected pixels : 191
updating NEVENTS keywords...
closing data file...
closing clean file...
-> Extracting bright and dark Earth events from ad50006000s000602h.unf
** XSELECT V1.3 **
!> Enter session name >[xsel] earthevents
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS S0CCDPOW
1 W50 EAST BRIGHT HIGH 28/04/93 22:52:12 0.15E+04 10533 1111
EXTRACTOR vers 2.0 11 Apr 1997.
Skipping file: /data/data17/seq_proc/50006000.007/ad50006000s000602h.unf
Writing events file
0 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
0 0 0 0 0 0
in 0.00 seconds
Command not found; type ? for a command listing
!earthevents:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!earthevents:ASCA > set datadir .
Setting data directory to /data/data17/seq_proc/50006000.007/
Setting mkf directory to /data/data17/seq_proc/50006000.007/
!earthevents:ASCA > read events ad50006000s000602h.unf
Got new instrument: SIS0
Setting: IMAGE binning = 4
WMAP binning = 8
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 2047
Got the minimum time resolution of the read data: 16.000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data17/seq_proc/50006000.007/
HK Directory is: /data/data17/seq_proc/50006000.007/
!earthevents:ASCA-SIS0-BRIGHT > select mkf "FOV==1" data_dir=. ASCA_mkf_def_expr=ft*.mkf
!earthevents:ASCA-SIS0-BRIGHT > extract events
!earthevents:ASCA-SIS0-BRIGHT > save events outfile=event.tmp use_events=no
Wrote events list to file event.tmp
!earthevents:ASCA-SIS0-BRIGHT > exit save_session=no
-> Deleting ad50006000s000602h.drk since it contains 0 events
** XSELECT V1.3 **
!> Enter session name >[xsel] earthevents
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS S0CCDPOW
1 W50 EAST BRIGHT2 HIGH 28/04/93 22:52:12 0.15E+04 10938 1111
EXTRACTOR vers 2.0 11 Apr 1997.
Skipping file: /data/data17/seq_proc/50006000.007/ad50006000s000612h.unf
Writing events file
0 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
0 0 0 0 0 0
in 0.00 seconds
Command not found; type ? for a command listing
!earthevents:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!earthevents:ASCA > set datadir .
Setting data directory to /data/data17/seq_proc/50006000.007/
Setting mkf directory to /data/data17/seq_proc/50006000.007/
!earthevents:ASCA > read events ad50006000s000612h.unf
Got new instrument: SIS0
Setting: IMAGE binning = 4
WMAP binning = 8
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 4095
Got the minimum time resolution of the read data: 16.000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data17/seq_proc/50006000.007/
HK Directory is: /data/data17/seq_proc/50006000.007/
!earthevents:ASCA-SIS0-BRIGHT2 > select mkf "FOV==1" data_dir=. ASCA_mkf_def_expr=ft*.mkf
!earthevents:ASCA-SIS0-BRIGHT2 > extract events
!earthevents:ASCA-SIS0-BRIGHT2 > save events outfile=event.tmp use_events=no
Wrote events list to file event.tmp
!earthevents:ASCA-SIS0-BRIGHT2 > exit save_session=no
-> Deleting ad50006000s000612h.drk since it contains 0 events
** XSELECT V1.3 **
!> Enter session name >[xsel] earthevents
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS S1CCDPOW
1 W50 EAST BRIGHT HIGH 28/04/93 03:44:28 0.24E+05 179196 1111
EXTRACTOR vers 2.0 11 Apr 1997.
Doing file: /data/data17/seq_proc/50006000.007/ad50006000s100102h.unf
Total Good Bad: Region Time Phase Cut
179196 25392 0 153804 0 0
Writing events file
25392 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
179196 25392 0 153804 0 0
in 3688.60 seconds
Command not found; type ? for a command listing
!earthevents:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!earthevents:ASCA > set datadir .
Setting data directory to /data/data17/seq_proc/50006000.007/
Setting mkf directory to /data/data17/seq_proc/50006000.007/
!earthevents:ASCA > read events ad50006000s100102h.unf
Got new instrument: SIS1
Setting: IMAGE binning = 4
WMAP binning = 8
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 2047
Got the minimum time resolution of the read data: 16.000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data17/seq_proc/50006000.007/
HK Directory is: /data/data17/seq_proc/50006000.007/
!earthevents:ASCA-SIS1-BRIGHT > select mkf "FOV==1" data_dir=. ASCA_mkf_def_expr=ft*.mkf
!earthevents:ASCA-SIS1-BRIGHT > extract events
!earthevents:ASCA-SIS1-BRIGHT > save events outfile=event.tmp use_events=no
Wrote events list to file event.tmp
!earthevents:ASCA-SIS1-BRIGHT > exit save_session=no
-> Cleaning hot pixels from ad50006000s100102h.unf
CLEANSIS_V1.6
allocating image arrays...
PROGRAM TO MAKE AN SIS SCIENCE FILE CLEANED OF ANOMALOUS PIXELS.
* Anomalous pixels may consist of at least two populations.
1. Persistent HOT pixels are removed by comparing to the chip mean.
2. Flickering WARM pixels are removed by comparing to the cell mean.
3. In faint areas (zero bgd), flickering pixels are removed with a
cutoff threshold.
Hints:
Choose cell size and thresholds based on the expected background and the PSF.
Use the DIRTYSIS option to examine the anomalous pixel spectra.
Try a multiple pass clean:
Choose a PHA cut to optimize the S/N of the flickering pixels,
then a broad band clean.
Be suspicious of extended source cleans.
For very bright sources you may need to turn off the iteration option.
See the help page for further info (fhelp cleansis)
Poisson clean cell size : 5
Poisson probability threshold : 0.575E-05
Zero Bgd Cutoff threshold (>) : 3
Iterate : F
Dirtysis : F
Minimum PHA value (inclusive) : 0
Maximum PHA value (inclusive) : 4095
open output file: ad50006000s100102h.drk
reading data file: event.tmp
copying primary header to output file...
making chip image...
Total counts in chip images : 25392
copy bad pix array...
cleaning chip # 0
Hot pixels & counts : 35 4994
Flickering pixels iter, pixels & cnts : 1 42 516
cleaning chip # 1
Hot pixels & counts : 36 6196
Flickering pixels iter, pixels & cnts : 1 206 1159
cleaning chip # 2
Hot pixels & counts : 34 5006
Flickering pixels iter, pixels & cnts : 1 18 218
cleaning chip # 3
Hot pixels & counts : 31 5521
Flickering pixels iter, pixels & cnts : 1 39 460
Number of pixels rejected : 441
Number of (internal) image counts : 25392
Number of image cts rejected (N, %) : 24070 94.7936325
By chip : 0 1 2 3
Pixels rejected : 77 242 52 70
Image counts : 5767 7939 5432 6254
Image cts rejected: 5510 7355 5224 5981
Image cts rej (%) : 95.54 92.64 96.17 95.63
filtering data...
Total counts : 5767 7939 5432 6254
Total cts rejected: 5510 7355 5224 5981
Total cts rej (%) : 95.54 92.64 96.17 95.63
Number of clean counts accepted : 1322
writing history cards...
copying extensions...
writing out hot pixs...
Number of rejected pixels : 441
updating NEVENTS keywords...
closing data file...
closing clean file...
-> Extracting bright and dark Earth events from ad50006000s100112h.unf
** XSELECT V1.3 **
!> Enter session name >[xsel] earthevents
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS S1CCDPOW
1 W50 EAST BRIGHT2 HIGH 28/04/93 03:44:28 0.24E+05 187467 1111
EXTRACTOR vers 2.0 11 Apr 1997.
Doing file: /data/data17/seq_proc/50006000.007/ad50006000s100112h.unf
Total Good Bad: Region Time Phase Cut
187467 26480 0 160987 0 0
Writing events file
26480 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
187467 26480 0 160987 0 0
in 3688.60 seconds
Command not found; type ? for a command listing
!earthevents:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!earthevents:ASCA > set datadir .
Setting data directory to /data/data17/seq_proc/50006000.007/
Setting mkf directory to /data/data17/seq_proc/50006000.007/
!earthevents:ASCA > read events ad50006000s100112h.unf
Got new instrument: SIS1
Setting: IMAGE binning = 4
WMAP binning = 8
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 4095
Got the minimum time resolution of the read data: 16.000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data17/seq_proc/50006000.007/
HK Directory is: /data/data17/seq_proc/50006000.007/
!earthevents:ASCA-SIS1-BRIGHT2 > select mkf "FOV==1" data_dir=. ASCA_mkf_def_expr=ft*.mkf
!earthevents:ASCA-SIS1-BRIGHT2 > extract events
!earthevents:ASCA-SIS1-BRIGHT2 > save events outfile=event.tmp use_events=no
Wrote events list to file event.tmp
!earthevents:ASCA-SIS1-BRIGHT2 > exit save_session=no
-> Cleaning hot pixels from ad50006000s100112h.unf
CLEANSIS_V1.6
allocating image arrays...
PROGRAM TO MAKE AN SIS SCIENCE FILE CLEANED OF ANOMALOUS PIXELS.
* Anomalous pixels may consist of at least two populations.
1. Persistent HOT pixels are removed by comparing to the chip mean.
2. Flickering WARM pixels are removed by comparing to the cell mean.
3. In faint areas (zero bgd), flickering pixels are removed with a
cutoff threshold.
Hints:
Choose cell size and thresholds based on the expected background and the PSF.
Use the DIRTYSIS option to examine the anomalous pixel spectra.
Try a multiple pass clean:
Choose a PHA cut to optimize the S/N of the flickering pixels,
then a broad band clean.
Be suspicious of extended source cleans.
For very bright sources you may need to turn off the iteration option.
See the help page for further info (fhelp cleansis)
Poisson clean cell size : 5
Poisson probability threshold : 0.575E-05
Zero Bgd Cutoff threshold (>) : 3
Iterate : F
Dirtysis : F
Minimum PHA value (inclusive) : 0
Maximum PHA value (inclusive) : 4095
open output file: ad50006000s100112h.drk
reading data file: event.tmp
copying primary header to output file...
making chip image...
Total counts in chip images : 26480
copy bad pix array...
cleaning chip # 0
Hot pixels & counts : 35 5011
Flickering pixels iter, pixels & cnts : 1 42 523
cleaning chip # 1
Hot pixels & counts : 36 6201
Flickering pixels iter, pixels & cnts : 1 211 1198
cleaning chip # 2
Hot pixels & counts : 33 4987
Flickering pixels iter, pixels & cnts : 1 19 246
cleaning chip # 3
Hot pixels & counts : 32 5892
Flickering pixels iter, pixels & cnts : 1 40 470
Number of pixels rejected : 448
Number of (internal) image counts : 26480
Number of image cts rejected (N, %) : 24528 92.6283951
By chip : 0 1 2 3
Pixels rejected : 77 247 52 72
Image counts : 5931 8134 5621 6794
Image cts rejected: 5534 7399 5233 6362
Image cts rej (%) : 93.31 90.96 93.10 93.64
filtering data...
Total counts : 5931 8134 5621 6794
Total cts rejected: 5534 7399 5233 6362
Total cts rej (%) : 93.31 90.96 93.10 93.64
Number of clean counts accepted : 1952
writing history cards...
copying extensions...
writing out hot pixs...
Number of rejected pixels : 448
updating NEVENTS keywords...
closing data file...
closing clean file...
-> Extracting bright and dark Earth events from ad50006000s100202m.unf
** XSELECT V1.3 **
!> Enter session name >[xsel] earthevents
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS S1CCDPOW
1 W50 EAST BRIGHT MEDIUM 27/04/93 23:50:32 0.32E+05 197039 1111
EXTRACTOR vers 2.0 11 Apr 1997.
Doing file: /data/data17/seq_proc/50006000.007/ad50006000s100202m.unf
Total Good Bad: Region Time Phase Cut
197039 43861 0 153178 0 0
Writing events file
43861 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
197039 43861 0 153178 0 0
in 6649.71 seconds
Command not found; type ? for a command listing
!earthevents:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!earthevents:ASCA > set datadir .
Setting data directory to /data/data17/seq_proc/50006000.007/
Setting mkf directory to /data/data17/seq_proc/50006000.007/
!earthevents:ASCA > read events ad50006000s100202m.unf
Got new instrument: SIS1
Setting: IMAGE binning = 4
WMAP binning = 8
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 2047
Got the minimum time resolution of the read data: 16.000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data17/seq_proc/50006000.007/
HK Directory is: /data/data17/seq_proc/50006000.007/
!earthevents:ASCA-SIS1-BRIGHT > select mkf "FOV==1" data_dir=. ASCA_mkf_def_expr=ft*.mkf
!earthevents:ASCA-SIS1-BRIGHT > extract events
!earthevents:ASCA-SIS1-BRIGHT > save events outfile=event.tmp use_events=no
Wrote events list to file event.tmp
!earthevents:ASCA-SIS1-BRIGHT > exit save_session=no
-> Cleaning hot pixels from ad50006000s100202m.unf
CLEANSIS_V1.6
allocating image arrays...
PROGRAM TO MAKE AN SIS SCIENCE FILE CLEANED OF ANOMALOUS PIXELS.
* Anomalous pixels may consist of at least two populations.
1. Persistent HOT pixels are removed by comparing to the chip mean.
2. Flickering WARM pixels are removed by comparing to the cell mean.
3. In faint areas (zero bgd), flickering pixels are removed with a
cutoff threshold.
Hints:
Choose cell size and thresholds based on the expected background and the PSF.
Use the DIRTYSIS option to examine the anomalous pixel spectra.
Try a multiple pass clean:
Choose a PHA cut to optimize the S/N of the flickering pixels,
then a broad band clean.
Be suspicious of extended source cleans.
For very bright sources you may need to turn off the iteration option.
See the help page for further info (fhelp cleansis)
Poisson clean cell size : 5
Poisson probability threshold : 0.575E-05
Zero Bgd Cutoff threshold (>) : 3
Iterate : F
Dirtysis : F
Minimum PHA value (inclusive) : 0
Maximum PHA value (inclusive) : 4095
open output file: ad50006000s100202m.drk
reading data file: event.tmp
copying primary header to output file...
making chip image...
File NEVENTS keyword value : 43861
Total counts in chip images : 43860
copy bad pix array...
cleaning chip # 0
Hot pixels & counts : 38 8989
Flickering pixels iter, pixels & cnts : 1 51 596
cleaning chip # 1
Hot pixels & counts : 37 11356
Flickering pixels iter, pixels & cnts : 1 42 546
cleaning chip # 2
Hot pixels & counts : 33 8720
Flickering pixels iter, pixels & cnts : 1 28 434
cleaning chip # 3
Hot pixels & counts : 33 9562
Flickering pixels iter, pixels & cnts : 1 50 650
Number of pixels rejected : 312
Number of (internal) image counts : 43860
Number of image cts rejected (N, %) : 40853 93.1440964
By chip : 0 1 2 3
Pixels rejected : 89 79 61 83
Image counts : 10362 12779 9785 10934
Image cts rejected: 9585 11902 9154 10212
Image cts rej (%) : 92.50 93.14 93.55 93.40
filtering data...
Total counts : 10362 12779 9786 10934
Total cts rejected: 9585 11902 9155 10212
Total cts rej (%) : 92.50 93.14 93.55 93.40
Number of clean counts accepted : 3007
writing history cards...
copying extensions...
writing out hot pixs...
Number of rejected pixels : 312
updating NEVENTS keywords...
closing data file...
closing clean file...
-> Extracting bright and dark Earth events from ad50006000s100302l.unf
** XSELECT V1.3 **
!> Enter session name >[xsel] earthevents
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS S1CCDPOW
1 W50 EAST BRIGHT LOW 28/04/93 01:05:12 0.18E+04 5104 1111
EXTRACTOR vers 2.0 11 Apr 1997.
Doing file: /data/data17/seq_proc/50006000.007/ad50006000s100302l.unf
Total Good Bad: Region Time Phase Cut
5104 4432 0 672 0 0
Writing events file
4432 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
5104 4432 0 672 0 0
in 684.98 seconds
Command not found; type ? for a command listing
!earthevents:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!earthevents:ASCA > set datadir .
Setting data directory to /data/data17/seq_proc/50006000.007/
Setting mkf directory to /data/data17/seq_proc/50006000.007/
!earthevents:ASCA > read events ad50006000s100302l.unf
Got new instrument: SIS1
Setting: IMAGE binning = 4
WMAP binning = 8
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 2047
Got the minimum time resolution of the read data: 16.000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data17/seq_proc/50006000.007/
HK Directory is: /data/data17/seq_proc/50006000.007/
!earthevents:ASCA-SIS1-BRIGHT > select mkf "FOV==1" data_dir=. ASCA_mkf_def_expr=ft*.mkf
!earthevents:ASCA-SIS1-BRIGHT > extract events
!earthevents:ASCA-SIS1-BRIGHT > save events outfile=event.tmp use_events=no
Wrote events list to file event.tmp
!earthevents:ASCA-SIS1-BRIGHT > exit save_session=no
-> Cleaning hot pixels from ad50006000s100302l.unf
CLEANSIS_V1.6
allocating image arrays...
PROGRAM TO MAKE AN SIS SCIENCE FILE CLEANED OF ANOMALOUS PIXELS.
* Anomalous pixels may consist of at least two populations.
1. Persistent HOT pixels are removed by comparing to the chip mean.
2. Flickering WARM pixels are removed by comparing to the cell mean.
3. In faint areas (zero bgd), flickering pixels are removed with a
cutoff threshold.
Hints:
Choose cell size and thresholds based on the expected background and the PSF.
Use the DIRTYSIS option to examine the anomalous pixel spectra.
Try a multiple pass clean:
Choose a PHA cut to optimize the S/N of the flickering pixels,
then a broad band clean.
Be suspicious of extended source cleans.
For very bright sources you may need to turn off the iteration option.
See the help page for further info (fhelp cleansis)
Poisson clean cell size : 5
Poisson probability threshold : 0.575E-05
Zero Bgd Cutoff threshold (>) : 3
Iterate : F
Dirtysis : F
Minimum PHA value (inclusive) : 0
Maximum PHA value (inclusive) : 4095
open output file: ad50006000s100302l.drk
reading data file: event.tmp
copying primary header to output file...
making chip image...
Total counts in chip images : 4432
copy bad pix array...
cleaning chip # 0
Hot pixels & counts : 28 883
Flickering pixels iter, pixels & cnts : 1 18 95
cleaning chip # 1
Hot pixels & counts : 29 1103
Flickering pixels iter, pixels & cnts : 1 9 56
cleaning chip # 2
Hot pixels & counts : 28 903
Flickering pixels iter, pixels & cnts : 1 10 48
cleaning chip # 3
Hot pixels & counts : 26 953
Flickering pixels iter, pixels & cnts : 1 8 38
Number of pixels rejected : 156
Number of (internal) image counts : 4432
Number of image cts rejected (N, %) : 4079 92.0352020
By chip : 0 1 2 3
Pixels rejected : 46 38 38 34
Image counts : 1079 1250 1023 1080
Image cts rejected: 978 1159 951 991
Image cts rej (%) : 90.64 92.72 92.96 91.76
filtering data...
Total counts : 1079 1250 1023 1080
Total cts rejected: 978 1159 951 991
Total cts rej (%) : 90.64 92.72 92.96 91.76
Number of clean counts accepted : 353
writing history cards...
copying extensions...
writing out hot pixs...
Number of rejected pixels : 156
updating NEVENTS keywords...
closing data file...
closing clean file...
-> Extracting bright and dark Earth events from ad50006000s100402h.unf
** XSELECT V1.3 **
!> Enter session name >[xsel] earthevents
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS S1CCDPOW
1 W50 EAST BRIGHT HIGH 28/04/93 14:13:12 0.15E+03 1052 1111
EXTRACTOR vers 2.0 11 Apr 1997.
Doing file: /data/data17/seq_proc/50006000.007/ad50006000s100402h.unf
Total Good Bad: Region Time Phase Cut
1052 1052 0 0 0 0
Writing events file
1052 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
1052 1052 0 0 0 0
in 149.91 seconds
Command not found; type ? for a command listing
!earthevents:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!earthevents:ASCA > set datadir .
Setting data directory to /data/data17/seq_proc/50006000.007/
Setting mkf directory to /data/data17/seq_proc/50006000.007/
!earthevents:ASCA > read events ad50006000s100402h.unf
Got new instrument: SIS1
Setting: IMAGE binning = 4
WMAP binning = 8
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 2047
Got the minimum time resolution of the read data: 16.000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data17/seq_proc/50006000.007/
HK Directory is: /data/data17/seq_proc/50006000.007/
!earthevents:ASCA-SIS1-BRIGHT > select mkf "FOV==1" data_dir=. ASCA_mkf_def_expr=ft*.mkf
!earthevents:ASCA-SIS1-BRIGHT > extract events
!earthevents:ASCA-SIS1-BRIGHT > save events outfile=event.tmp use_events=no
Wrote events list to file event.tmp
!earthevents:ASCA-SIS1-BRIGHT > exit save_session=no
-> Cleaning hot pixels from ad50006000s100402h.unf
CLEANSIS_V1.6
allocating image arrays...
PROGRAM TO MAKE AN SIS SCIENCE FILE CLEANED OF ANOMALOUS PIXELS.
* Anomalous pixels may consist of at least two populations.
1. Persistent HOT pixels are removed by comparing to the chip mean.
2. Flickering WARM pixels are removed by comparing to the cell mean.
3. In faint areas (zero bgd), flickering pixels are removed with a
cutoff threshold.
Hints:
Choose cell size and thresholds based on the expected background and the PSF.
Use the DIRTYSIS option to examine the anomalous pixel spectra.
Try a multiple pass clean:
Choose a PHA cut to optimize the S/N of the flickering pixels,
then a broad band clean.
Be suspicious of extended source cleans.
For very bright sources you may need to turn off the iteration option.
See the help page for further info (fhelp cleansis)
Poisson clean cell size : 5
Poisson probability threshold : 0.575E-05
Zero Bgd Cutoff threshold (>) : 3
Iterate : F
Dirtysis : F
Minimum PHA value (inclusive) : 0
Maximum PHA value (inclusive) : 4095
open output file: ad50006000s100402h.drk
reading data file: event.tmp
copying primary header to output file...
making chip image...
Total counts in chip images : 1052
copy bad pix array...
cleaning chip # 0
Hot pixels & counts : 19 156
Flickering pixels iter, pixels & cnts : 1 9 35
cleaning chip # 1
Hot pixels & counts : 27 224
Flickering pixels iter, pixels & cnts : 1 5 17
cleaning chip # 2
Hot pixels & counts : 22 237
Flickering pixels iter, pixels & cnts : 1 5 20
cleaning chip # 3
Hot pixels & counts : 23 193
Flickering pixels iter, pixels & cnts : 1 5 19
Number of pixels rejected : 115
Number of (internal) image counts : 1052
Number of image cts rejected (N, %) : 901 85.6463852
By chip : 0 1 2 3
Pixels rejected : 28 32 27 28
Image counts : 227 273 292 260
Image cts rejected: 191 241 257 212
Image cts rej (%) : 84.14 88.28 88.01 81.54
filtering data...
Total counts : 227 273 292 260
Total cts rejected: 191 241 257 212
Total cts rej (%) : 84.14 88.28 88.01 81.54
Number of clean counts accepted : 151
writing history cards...
copying extensions...
writing out hot pixs...
Number of rejected pixels : 115
updating NEVENTS keywords...
closing data file...
closing clean file...
-> Extracting bright and dark Earth events from ad50006000s100502m.unf
** XSELECT V1.3 **
!> Enter session name >[xsel] earthevents
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS S1CCDPOW
1 W50 EAST BRIGHT MEDIUM 28/04/93 19:50:16 0.12E+05 70315 1111
EXTRACTOR vers 2.0 11 Apr 1997.
Doing file: /data/data17/seq_proc/50006000.007/ad50006000s100502m.unf
Total Good Bad: Region Time Phase Cut
70315 9236 0 61079 0 0
Writing events file
9236 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
70315 9236 0 61079 0 0
in 1459.44 seconds
Command not found; type ? for a command listing
!earthevents:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!earthevents:ASCA > set datadir .
Setting data directory to /data/data17/seq_proc/50006000.007/
Setting mkf directory to /data/data17/seq_proc/50006000.007/
!earthevents:ASCA > read events ad50006000s100502m.unf
Got new instrument: SIS1
Setting: IMAGE binning = 4
WMAP binning = 8
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 2047
Got the minimum time resolution of the read data: 16.000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data17/seq_proc/50006000.007/
HK Directory is: /data/data17/seq_proc/50006000.007/
!earthevents:ASCA-SIS1-BRIGHT > select mkf "FOV==1" data_dir=. ASCA_mkf_def_expr=ft*.mkf
!earthevents:ASCA-SIS1-BRIGHT > extract events
!earthevents:ASCA-SIS1-BRIGHT > save events outfile=event.tmp use_events=no
Wrote events list to file event.tmp
!earthevents:ASCA-SIS1-BRIGHT > exit save_session=no
-> Cleaning hot pixels from ad50006000s100502m.unf
CLEANSIS_V1.6
allocating image arrays...
PROGRAM TO MAKE AN SIS SCIENCE FILE CLEANED OF ANOMALOUS PIXELS.
* Anomalous pixels may consist of at least two populations.
1. Persistent HOT pixels are removed by comparing to the chip mean.
2. Flickering WARM pixels are removed by comparing to the cell mean.
3. In faint areas (zero bgd), flickering pixels are removed with a
cutoff threshold.
Hints:
Choose cell size and thresholds based on the expected background and the PSF.
Use the DIRTYSIS option to examine the anomalous pixel spectra.
Try a multiple pass clean:
Choose a PHA cut to optimize the S/N of the flickering pixels,
then a broad band clean.
Be suspicious of extended source cleans.
For very bright sources you may need to turn off the iteration option.
See the help page for further info (fhelp cleansis)
Poisson clean cell size : 5
Poisson probability threshold : 0.575E-05
Zero Bgd Cutoff threshold (>) : 3
Iterate : F
Dirtysis : F
Minimum PHA value (inclusive) : 0
Maximum PHA value (inclusive) : 4095
open output file: ad50006000s100502m.drk
reading data file: event.tmp
copying primary header to output file...
making chip image...
Total counts in chip images : 9236
copy bad pix array...
cleaning chip # 0
Hot pixels & counts : 28 1618
Flickering pixels iter, pixels & cnts : 1 22 132
cleaning chip # 1
Hot pixels & counts : 32 2126
Flickering pixels iter, pixels & cnts : 1 21 131
cleaning chip # 2
Hot pixels & counts : 24 1460
Flickering pixels iter, pixels & cnts : 1 22 127
cleaning chip # 3
Hot pixels & counts : 29 1795
Flickering pixels iter, pixels & cnts : 1 17 109
Number of pixels rejected : 195
Number of (internal) image counts : 9236
Number of image cts rejected (N, %) : 7498 81.1823273
By chip : 0 1 2 3
Pixels rejected : 50 53 46 46
Image counts : 2213 2724 1988 2311
Image cts rejected: 1750 2257 1587 1904
Image cts rej (%) : 79.08 82.86 79.83 82.39
filtering data...
Total counts : 2213 2724 1988 2311
Total cts rejected: 1750 2257 1587 1904
Total cts rej (%) : 79.08 82.86 79.83 82.39
Number of clean counts accepted : 1738
writing history cards...
copying extensions...
writing out hot pixs...
Number of rejected pixels : 195
updating NEVENTS keywords...
closing data file...
closing clean file...
-> Extracting bright and dark Earth events from ad50006000s100602h.unf
** XSELECT V1.3 **
!> Enter session name >[xsel] earthevents
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS S1CCDPOW
1 W50 EAST BRIGHT HIGH 28/04/93 22:52:12 0.15E+04 11111 1111
EXTRACTOR vers 2.0 11 Apr 1997.
Skipping file: /data/data17/seq_proc/50006000.007/ad50006000s100602h.unf
Writing events file
0 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
0 0 0 0 0 0
in 0.00 seconds
Command not found; type ? for a command listing
!earthevents:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!earthevents:ASCA > set datadir .
Setting data directory to /data/data17/seq_proc/50006000.007/
Setting mkf directory to /data/data17/seq_proc/50006000.007/
!earthevents:ASCA > read events ad50006000s100602h.unf
Got new instrument: SIS1
Setting: IMAGE binning = 4
WMAP binning = 8
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 2047
Got the minimum time resolution of the read data: 16.000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data17/seq_proc/50006000.007/
HK Directory is: /data/data17/seq_proc/50006000.007/
!earthevents:ASCA-SIS1-BRIGHT > select mkf "FOV==1" data_dir=. ASCA_mkf_def_expr=ft*.mkf
!earthevents:ASCA-SIS1-BRIGHT > extract events
!earthevents:ASCA-SIS1-BRIGHT > save events outfile=event.tmp use_events=no
Wrote events list to file event.tmp
!earthevents:ASCA-SIS1-BRIGHT > exit save_session=no
-> Deleting ad50006000s100602h.drk since it contains 0 events
** XSELECT V1.3 **
!> Enter session name >[xsel] earthevents
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS S1CCDPOW
1 W50 EAST BRIGHT2 HIGH 28/04/93 22:52:12 0.15E+04 11616 1111
EXTRACTOR vers 2.0 11 Apr 1997.
Skipping file: /data/data17/seq_proc/50006000.007/ad50006000s100612h.unf
Writing events file
0 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
0 0 0 0 0 0
in 0.00 seconds
Command not found; type ? for a command listing
!earthevents:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!earthevents:ASCA > set datadir .
Setting data directory to /data/data17/seq_proc/50006000.007/
Setting mkf directory to /data/data17/seq_proc/50006000.007/
!earthevents:ASCA > read events ad50006000s100612h.unf
Got new instrument: SIS1
Setting: IMAGE binning = 4
WMAP binning = 8
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 4095
Got the minimum time resolution of the read data: 16.000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data17/seq_proc/50006000.007/
HK Directory is: /data/data17/seq_proc/50006000.007/
!earthevents:ASCA-SIS1-BRIGHT2 > select mkf "FOV==1" data_dir=. ASCA_mkf_def_expr=ft*.mkf
!earthevents:ASCA-SIS1-BRIGHT2 > extract events
!earthevents:ASCA-SIS1-BRIGHT2 > save events outfile=event.tmp use_events=no
Wrote events list to file event.tmp
!earthevents:ASCA-SIS1-BRIGHT2 > exit save_session=no
-> Deleting ad50006000s100612h.drk since it contains 0 events
** XSELECT V1.3 **
!> Enter session name >[xsel] earthevents
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS PHA_BINS
1 W50 EAST PH MEDIUM 27/04/93 23:50:48 0.27E+05 82925 1024
EXTRACTOR vers 2.0 11 Apr 1997.
Doing file: /data/data17/seq_proc/50006000.007/ad50006000g200170m.unf
Total Good Bad: Region Time Phase Cut
82925 11102 0 71823 0 0
Writing events file
11102 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
82925 11102 0 71823 0 0
in 5663.76 seconds
Command not found; type ? for a command listing
!earthevents:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!earthevents:ASCA > set datadir .
Setting data directory to /data/data17/seq_proc/50006000.007/
Setting mkf directory to /data/data17/seq_proc/50006000.007/
!earthevents:ASCA > read events ad50006000g200170m.unf
Got new instrument: GIS2
Setting: IMAGE binning = 1
WMAP binning = 1
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 1023
Got the minimum time resolution of the read data: 0.50000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data17/seq_proc/50006000.007/
HK Directory is: /data/data17/seq_proc/50006000.007/
!earthevents:ASCA-GIS2-PH > select mkf "FOV==1" data_dir=. ASCA_mkf_def_expr=ft*.mkf
!earthevents:ASCA-GIS2-PH > extract events
!earthevents:ASCA-GIS2-PH > save events outfile=event.tmp use_events=no
Wrote events list to file event.tmp
!earthevents:ASCA-GIS2-PH > exit save_session=no
-> Extracting ad50006000g200170m.brt
** XSELECT V1.3 **
!> Enter session name >[xsel] earthevents
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS PHA_BINS
1 W50 EAST PH MEDIUM 27/04/93 23:50:48 0.27E+05 82925 1024
EXTRACTOR vers 2.0 11 Apr 1997.
Doing file: /data/data17/seq_proc/50006000.007/ad50006000g200170m.unf
Total Good Bad: Region Time Phase Cut
82925 25015 0 57910 0 0
Writing events file
25015 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
82925 25015 0 57910 0 0
in 5664.24 seconds
Command not found; type ? for a command listing
!earthevents:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!earthevents:ASCA > set datadir .
Setting data directory to /data/data17/seq_proc/50006000.007/
Setting mkf directory to /data/data17/seq_proc/50006000.007/
!earthevents:ASCA > read events ad50006000g200170m.unf
Got new instrument: GIS2
Setting: IMAGE binning = 1
WMAP binning = 1
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 1023
Got the minimum time resolution of the read data: 0.50000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data17/seq_proc/50006000.007/
HK Directory is: /data/data17/seq_proc/50006000.007/
!earthevents:ASCA-GIS2-PH > select mkf "FOV==2" data_dir=. ASCA_mkf_def_expr=ft*.mkf
!earthevents:ASCA-GIS2-PH > extract events
!earthevents:ASCA-GIS2-PH > save events outfile=event.tmp use_events=no
Wrote events list to file event.tmp
!earthevents:ASCA-GIS2-PH > exit save_session=no
-> Extracting bright and dark Earth events from ad50006000g200270h.unf
** XSELECT V1.3 **
!> Enter session name >[xsel] earthevents
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS PHA_BINS
1 W50 EAST PH HIGH 28/04/93 03:44:46 0.24E+05 60324 1024
EXTRACTOR vers 2.0 11 Apr 1997.
Doing file: /data/data17/seq_proc/50006000.007/ad50006000g200270h.unf
Total Good Bad: Region Time Phase Cut
60324 6909 0 53415 0 0
Writing events file
6909 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
60324 6909 0 53415 0 0
in 3736.73 seconds
Command not found; type ? for a command listing
!earthevents:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!earthevents:ASCA > set datadir .
Setting data directory to /data/data17/seq_proc/50006000.007/
Setting mkf directory to /data/data17/seq_proc/50006000.007/
!earthevents:ASCA > read events ad50006000g200270h.unf
Got new instrument: GIS2
Setting: IMAGE binning = 1
WMAP binning = 1
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 1023
Got the minimum time resolution of the read data: 0.62500E-01
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data17/seq_proc/50006000.007/
HK Directory is: /data/data17/seq_proc/50006000.007/
!earthevents:ASCA-GIS2-PH > select mkf "FOV==1" data_dir=. ASCA_mkf_def_expr=ft*.mkf
!earthevents:ASCA-GIS2-PH > extract events
!earthevents:ASCA-GIS2-PH > save events outfile=event.tmp use_events=no
Wrote events list to file event.tmp
!earthevents:ASCA-GIS2-PH > exit save_session=no
-> Extracting ad50006000g200270h.brt
** XSELECT V1.3 **
!> Enter session name >[xsel] earthevents
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS PHA_BINS
1 W50 EAST PH HIGH 28/04/93 03:44:46 0.24E+05 60324 1024
EXTRACTOR vers 2.0 11 Apr 1997.
Doing file: /data/data17/seq_proc/50006000.007/ad50006000g200270h.unf
Total Good Bad: Region Time Phase Cut
60324 293 0 60031 0 0
Writing events file
293 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
60324 293 0 60031 0 0
in 171.93 seconds
Command not found; type ? for a command listing
!earthevents:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!earthevents:ASCA > set datadir .
Setting data directory to /data/data17/seq_proc/50006000.007/
Setting mkf directory to /data/data17/seq_proc/50006000.007/
!earthevents:ASCA > read events ad50006000g200270h.unf
Got new instrument: GIS2
Setting: IMAGE binning = 1
WMAP binning = 1
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 1023
Got the minimum time resolution of the read data: 0.62500E-01
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data17/seq_proc/50006000.007/
HK Directory is: /data/data17/seq_proc/50006000.007/
!earthevents:ASCA-GIS2-PH > select mkf "FOV==2" data_dir=. ASCA_mkf_def_expr=ft*.mkf
!earthevents:ASCA-GIS2-PH > extract events
!earthevents:ASCA-GIS2-PH > save events outfile=event.tmp use_events=no
Wrote events list to file event.tmp
!earthevents:ASCA-GIS2-PH > exit save_session=no
-> Extracting bright and dark Earth events from ad50006000g200370l.unf
** XSELECT V1.3 **
!> Enter session name >[xsel] earthevents
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS PHA_BINS
1 W50 EAST PH LOW 28/04/93 01:05:28 0.18E+04 4648 1024
EXTRACTOR vers 2.0 11 Apr 1997.
Doing file: /data/data17/seq_proc/50006000.007/ad50006000g200370l.unf
Total Good Bad: Region Time Phase Cut
4648 1181 0 3467 0 0
Writing events file
1181 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
4648 1181 0 3467 0 0
in 703.98 seconds
Command not found; type ? for a command listing
!earthevents:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!earthevents:ASCA > set datadir .
Setting data directory to /data/data17/seq_proc/50006000.007/
Setting mkf directory to /data/data17/seq_proc/50006000.007/
!earthevents:ASCA > read events ad50006000g200370l.unf
Got new instrument: GIS2
Setting: IMAGE binning = 1
WMAP binning = 1
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 1023
Got the minimum time resolution of the read data: 2.0000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data17/seq_proc/50006000.007/
HK Directory is: /data/data17/seq_proc/50006000.007/
!earthevents:ASCA-GIS2-PH > select mkf "FOV==1" data_dir=. ASCA_mkf_def_expr=ft*.mkf
!earthevents:ASCA-GIS2-PH > extract events
!earthevents:ASCA-GIS2-PH > save events outfile=event.tmp use_events=no
Wrote events list to file event.tmp
!earthevents:ASCA-GIS2-PH > exit save_session=no
-> Extracting ad50006000g200370l.brt
** XSELECT V1.3 **
!> Enter session name >[xsel] earthevents
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS PHA_BINS
1 W50 EAST PH LOW 28/04/93 01:05:28 0.18E+04 4648 1024
EXTRACTOR vers 2.0 11 Apr 1997.
Doing file: /data/data17/seq_proc/50006000.007/ad50006000g200370l.unf
Total Good Bad: Region Time Phase Cut
4648 3467 0 1181 0 0
Writing events file
3467 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
4648 3467 0 1181 0 0
in 1088.00 seconds
Command not found; type ? for a command listing
!earthevents:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!earthevents:ASCA > set datadir .
Setting data directory to /data/data17/seq_proc/50006000.007/
Setting mkf directory to /data/data17/seq_proc/50006000.007/
!earthevents:ASCA > read events ad50006000g200370l.unf
Got new instrument: GIS2
Setting: IMAGE binning = 1
WMAP binning = 1
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 1023
Got the minimum time resolution of the read data: 2.0000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data17/seq_proc/50006000.007/
HK Directory is: /data/data17/seq_proc/50006000.007/
!earthevents:ASCA-GIS2-PH > select mkf "FOV==2" data_dir=. ASCA_mkf_def_expr=ft*.mkf
!earthevents:ASCA-GIS2-PH > extract events
!earthevents:ASCA-GIS2-PH > save events outfile=event.tmp use_events=no
Wrote events list to file event.tmp
!earthevents:ASCA-GIS2-PH > exit save_session=no
-> Extracting bright and dark Earth events from ad50006000g200470m.unf
** XSELECT V1.3 **
!> Enter session name >[xsel] earthevents
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS PHA_BINS
1 W50 EAST PH MEDIUM 28/04/93 19:50:32 0.99E+04 26977 1024
EXTRACTOR vers 2.0 11 Apr 1997.
Doing file: /data/data17/seq_proc/50006000.007/ad50006000g200470m.unf
Total Good Bad: Region Time Phase Cut
26977 925 0 26052 0 0
Writing events file
925 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
26977 925 0 26052 0 0
in 440.01 seconds
Command not found; type ? for a command listing
!earthevents:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!earthevents:ASCA > set datadir .
Setting data directory to /data/data17/seq_proc/50006000.007/
Setting mkf directory to /data/data17/seq_proc/50006000.007/
!earthevents:ASCA > read events ad50006000g200470m.unf
Got new instrument: GIS2
Setting: IMAGE binning = 1
WMAP binning = 1
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 1023
Got the minimum time resolution of the read data: 0.50000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data17/seq_proc/50006000.007/
HK Directory is: /data/data17/seq_proc/50006000.007/
!earthevents:ASCA-GIS2-PH > select mkf "FOV==1" data_dir=. ASCA_mkf_def_expr=ft*.mkf
!earthevents:ASCA-GIS2-PH > extract events
!earthevents:ASCA-GIS2-PH > save events outfile=event.tmp use_events=no
Wrote events list to file event.tmp
!earthevents:ASCA-GIS2-PH > exit save_session=no
-> Extracting ad50006000g200470m.brt
** XSELECT V1.3 **
!> Enter session name >[xsel] earthevents
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS PHA_BINS
1 W50 EAST PH MEDIUM 28/04/93 19:50:32 0.99E+04 26977 1024
EXTRACTOR vers 2.0 11 Apr 1997.
Doing file: /data/data17/seq_proc/50006000.007/ad50006000g200470m.unf
Total Good Bad: Region Time Phase Cut
26977 7381 0 19596 0 0
Writing events file
7381 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
26977 7381 0 19596 0 0
in 2191.97 seconds
Command not found; type ? for a command listing
!earthevents:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!earthevents:ASCA > set datadir .
Setting data directory to /data/data17/seq_proc/50006000.007/
Setting mkf directory to /data/data17/seq_proc/50006000.007/
!earthevents:ASCA > read events ad50006000g200470m.unf
Got new instrument: GIS2
Setting: IMAGE binning = 1
WMAP binning = 1
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 1023
Got the minimum time resolution of the read data: 0.50000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data17/seq_proc/50006000.007/
HK Directory is: /data/data17/seq_proc/50006000.007/
!earthevents:ASCA-GIS2-PH > select mkf "FOV==2" data_dir=. ASCA_mkf_def_expr=ft*.mkf
!earthevents:ASCA-GIS2-PH > extract events
!earthevents:ASCA-GIS2-PH > save events outfile=event.tmp use_events=no
Wrote events list to file event.tmp
!earthevents:ASCA-GIS2-PH > exit save_session=no
-> Extracting bright and dark Earth events from ad50006000g200570h.unf
** XSELECT V1.3 **
!> Enter session name >[xsel] earthevents
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS PHA_BINS
1 W50 EAST PH HIGH 28/04/93 22:52:30 0.15E+04 3692 1024
EXTRACTOR vers 2.0 11 Apr 1997.
Skipping file: /data/data17/seq_proc/50006000.007/ad50006000g200570h.unf
Writing events file
0 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
0 0 0 0 0 0
in 0.00 seconds
Command not found; type ? for a command listing
!earthevents:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!earthevents:ASCA > set datadir .
Setting data directory to /data/data17/seq_proc/50006000.007/
Setting mkf directory to /data/data17/seq_proc/50006000.007/
!earthevents:ASCA > read events ad50006000g200570h.unf
Got new instrument: GIS2
Setting: IMAGE binning = 1
WMAP binning = 1
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 1023
Got the minimum time resolution of the read data: 0.62500E-01
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data17/seq_proc/50006000.007/
HK Directory is: /data/data17/seq_proc/50006000.007/
!earthevents:ASCA-GIS2-PH > select mkf "FOV==1" data_dir=. ASCA_mkf_def_expr=ft*.mkf
!earthevents:ASCA-GIS2-PH > extract events
!earthevents:ASCA-GIS2-PH > save events outfile=event.tmp use_events=no
Wrote events list to file event.tmp
!earthevents:ASCA-GIS2-PH > exit save_session=no
-> Deleting ad50006000g200570h.drk since it contains 0 events
** XSELECT V1.3 **
!> Enter session name >[xsel] earthevents
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS PHA_BINS
1 W50 EAST PH HIGH 28/04/93 22:52:30 0.15E+04 3692 1024
EXTRACTOR vers 2.0 11 Apr 1997.
Skipping file: /data/data17/seq_proc/50006000.007/ad50006000g200570h.unf
Writing events file
0 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
0 0 0 0 0 0
in 0.00 seconds
Command not found; type ? for a command listing
!earthevents:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!earthevents:ASCA > set datadir .
Setting data directory to /data/data17/seq_proc/50006000.007/
Setting mkf directory to /data/data17/seq_proc/50006000.007/
!earthevents:ASCA > read events ad50006000g200570h.unf
Got new instrument: GIS2
Setting: IMAGE binning = 1
WMAP binning = 1
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 1023
Got the minimum time resolution of the read data: 0.62500E-01
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data17/seq_proc/50006000.007/
HK Directory is: /data/data17/seq_proc/50006000.007/
!earthevents:ASCA-GIS2-PH > select mkf "FOV==2" data_dir=. ASCA_mkf_def_expr=ft*.mkf
!earthevents:ASCA-GIS2-PH > extract events
!earthevents:ASCA-GIS2-PH > save events outfile=event.tmp use_events=no
Wrote events list to file event.tmp
!earthevents:ASCA-GIS2-PH > exit save_session=no
-> Deleting ad50006000g200570h.brt since it contains 0 events
** XSELECT V1.3 **
!> Enter session name >[xsel] earthevents
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS PHA_BINS
1 W50 EAST PH MEDIUM 27/04/93 23:50:48 0.27E+05 79675 1024
EXTRACTOR vers 2.0 11 Apr 1997.
Doing file: /data/data17/seq_proc/50006000.007/ad50006000g300170m.unf
Total Good Bad: Region Time Phase Cut
79675 10347 0 69328 0 0
Writing events file
10347 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
79675 10347 0 69328 0 0
in 5663.76 seconds
Command not found; type ? for a command listing
!earthevents:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!earthevents:ASCA > set datadir .
Setting data directory to /data/data17/seq_proc/50006000.007/
Setting mkf directory to /data/data17/seq_proc/50006000.007/
!earthevents:ASCA > read events ad50006000g300170m.unf
Got new instrument: GIS3
Setting: IMAGE binning = 1
WMAP binning = 1
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 1023
Got the minimum time resolution of the read data: 0.50000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data17/seq_proc/50006000.007/
HK Directory is: /data/data17/seq_proc/50006000.007/
!earthevents:ASCA-GIS3-PH > select mkf "FOV==1" data_dir=. ASCA_mkf_def_expr=ft*.mkf
!earthevents:ASCA-GIS3-PH > extract events
!earthevents:ASCA-GIS3-PH > save events outfile=event.tmp use_events=no
Wrote events list to file event.tmp
!earthevents:ASCA-GIS3-PH > exit save_session=no
-> Extracting ad50006000g300170m.brt
** XSELECT V1.3 **
!> Enter session name >[xsel] earthevents
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS PHA_BINS
1 W50 EAST PH MEDIUM 27/04/93 23:50:48 0.27E+05 79675 1024
EXTRACTOR vers 2.0 11 Apr 1997.
Doing file: /data/data17/seq_proc/50006000.007/ad50006000g300170m.unf
Total Good Bad: Region Time Phase Cut
79675 24456 0 55219 0 0
Writing events file
24456 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
79675 24456 0 55219 0 0
in 5664.24 seconds
Command not found; type ? for a command listing
!earthevents:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!earthevents:ASCA > set datadir .
Setting data directory to /data/data17/seq_proc/50006000.007/
Setting mkf directory to /data/data17/seq_proc/50006000.007/
!earthevents:ASCA > read events ad50006000g300170m.unf
Got new instrument: GIS3
Setting: IMAGE binning = 1
WMAP binning = 1
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 1023
Got the minimum time resolution of the read data: 0.50000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data17/seq_proc/50006000.007/
HK Directory is: /data/data17/seq_proc/50006000.007/
!earthevents:ASCA-GIS3-PH > select mkf "FOV==2" data_dir=. ASCA_mkf_def_expr=ft*.mkf
!earthevents:ASCA-GIS3-PH > extract events
!earthevents:ASCA-GIS3-PH > save events outfile=event.tmp use_events=no
Wrote events list to file event.tmp
!earthevents:ASCA-GIS3-PH > exit save_session=no
-> Extracting bright and dark Earth events from ad50006000g300270h.unf
** XSELECT V1.3 **
!> Enter session name >[xsel] earthevents
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS PHA_BINS
1 W50 EAST PH HIGH 28/04/93 03:44:46 0.24E+05 57073 1024
EXTRACTOR vers 2.0 11 Apr 1997.
Doing file: /data/data17/seq_proc/50006000.007/ad50006000g300270h.unf
Total Good Bad: Region Time Phase Cut
57073 6307 0 50766 0 0
Writing events file
6307 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
57073 6307 0 50766 0 0
in 3726.73 seconds
Command not found; type ? for a command listing
!earthevents:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!earthevents:ASCA > set datadir .
Setting data directory to /data/data17/seq_proc/50006000.007/
Setting mkf directory to /data/data17/seq_proc/50006000.007/
!earthevents:ASCA > read events ad50006000g300270h.unf
Got new instrument: GIS3
Setting: IMAGE binning = 1
WMAP binning = 1
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 1023
Got the minimum time resolution of the read data: 0.62500E-01
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data17/seq_proc/50006000.007/
HK Directory is: /data/data17/seq_proc/50006000.007/
!earthevents:ASCA-GIS3-PH > select mkf "FOV==1" data_dir=. ASCA_mkf_def_expr=ft*.mkf
!earthevents:ASCA-GIS3-PH > extract events
!earthevents:ASCA-GIS3-PH > save events outfile=event.tmp use_events=no
Wrote events list to file event.tmp
!earthevents:ASCA-GIS3-PH > exit save_session=no
-> Extracting ad50006000g300270h.brt
** XSELECT V1.3 **
!> Enter session name >[xsel] earthevents
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS PHA_BINS
1 W50 EAST PH HIGH 28/04/93 03:44:46 0.24E+05 57073 1024
EXTRACTOR vers 2.0 11 Apr 1997.
Doing file: /data/data17/seq_proc/50006000.007/ad50006000g300270h.unf
Total Good Bad: Region Time Phase Cut
57073 305 0 56768 0 0
Writing events file
305 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
57073 305 0 56768 0 0
in 171.93 seconds
Command not found; type ? for a command listing
!earthevents:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!earthevents:ASCA > set datadir .
Setting data directory to /data/data17/seq_proc/50006000.007/
Setting mkf directory to /data/data17/seq_proc/50006000.007/
!earthevents:ASCA > read events ad50006000g300270h.unf
Got new instrument: GIS3
Setting: IMAGE binning = 1
WMAP binning = 1
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 1023
Got the minimum time resolution of the read data: 0.62500E-01
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data17/seq_proc/50006000.007/
HK Directory is: /data/data17/seq_proc/50006000.007/
!earthevents:ASCA-GIS3-PH > select mkf "FOV==2" data_dir=. ASCA_mkf_def_expr=ft*.mkf
!earthevents:ASCA-GIS3-PH > extract events
!earthevents:ASCA-GIS3-PH > save events outfile=event.tmp use_events=no
Wrote events list to file event.tmp
!earthevents:ASCA-GIS3-PH > exit save_session=no
-> Extracting bright and dark Earth events from ad50006000g300370l.unf
** XSELECT V1.3 **
!> Enter session name >[xsel] earthevents
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS PHA_BINS
1 W50 EAST PH LOW 28/04/93 01:05:28 0.18E+04 4709 1024
EXTRACTOR vers 2.0 11 Apr 1997.
Doing file: /data/data17/seq_proc/50006000.007/ad50006000g300370l.unf
Total Good Bad: Region Time Phase Cut
4709 1216 0 3493 0 0
Writing events file
1216 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
4709 1216 0 3493 0 0
in 703.98 seconds
Command not found; type ? for a command listing
!earthevents:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!earthevents:ASCA > set datadir .
Setting data directory to /data/data17/seq_proc/50006000.007/
Setting mkf directory to /data/data17/seq_proc/50006000.007/
!earthevents:ASCA > read events ad50006000g300370l.unf
Got new instrument: GIS3
Setting: IMAGE binning = 1
WMAP binning = 1
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 1023
Got the minimum time resolution of the read data: 2.0000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data17/seq_proc/50006000.007/
HK Directory is: /data/data17/seq_proc/50006000.007/
!earthevents:ASCA-GIS3-PH > select mkf "FOV==1" data_dir=. ASCA_mkf_def_expr=ft*.mkf
!earthevents:ASCA-GIS3-PH > extract events
!earthevents:ASCA-GIS3-PH > save events outfile=event.tmp use_events=no
Wrote events list to file event.tmp
!earthevents:ASCA-GIS3-PH > exit save_session=no
-> Extracting ad50006000g300370l.brt
** XSELECT V1.3 **
!> Enter session name >[xsel] earthevents
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS PHA_BINS
1 W50 EAST PH LOW 28/04/93 01:05:28 0.18E+04 4709 1024
EXTRACTOR vers 2.0 11 Apr 1997.
Doing file: /data/data17/seq_proc/50006000.007/ad50006000g300370l.unf
Total Good Bad: Region Time Phase Cut
4709 3493 0 1216 0 0
Writing events file
3493 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
4709 3493 0 1216 0 0
in 1088.00 seconds
Command not found; type ? for a command listing
!earthevents:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!earthevents:ASCA > set datadir .
Setting data directory to /data/data17/seq_proc/50006000.007/
Setting mkf directory to /data/data17/seq_proc/50006000.007/
!earthevents:ASCA > read events ad50006000g300370l.unf
Got new instrument: GIS3
Setting: IMAGE binning = 1
WMAP binning = 1
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 1023
Got the minimum time resolution of the read data: 2.0000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data17/seq_proc/50006000.007/
HK Directory is: /data/data17/seq_proc/50006000.007/
!earthevents:ASCA-GIS3-PH > select mkf "FOV==2" data_dir=. ASCA_mkf_def_expr=ft*.mkf
!earthevents:ASCA-GIS3-PH > extract events
!earthevents:ASCA-GIS3-PH > save events outfile=event.tmp use_events=no
Wrote events list to file event.tmp
!earthevents:ASCA-GIS3-PH > exit save_session=no
-> Extracting bright and dark Earth events from ad50006000g300470m.unf
** XSELECT V1.3 **
!> Enter session name >[xsel] earthevents
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS PHA_BINS
1 W50 EAST PH MEDIUM 28/04/93 19:50:32 0.99E+04 26610 1024
EXTRACTOR vers 2.0 11 Apr 1997.
Doing file: /data/data17/seq_proc/50006000.007/ad50006000g300470m.unf
Total Good Bad: Region Time Phase Cut
26610 850 0 25760 0 0
Writing events file
850 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
26610 850 0 25760 0 0
in 440.01 seconds
Command not found; type ? for a command listing
!earthevents:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!earthevents:ASCA > set datadir .
Setting data directory to /data/data17/seq_proc/50006000.007/
Setting mkf directory to /data/data17/seq_proc/50006000.007/
!earthevents:ASCA > read events ad50006000g300470m.unf
Got new instrument: GIS3
Setting: IMAGE binning = 1
WMAP binning = 1
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 1023
Got the minimum time resolution of the read data: 0.50000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data17/seq_proc/50006000.007/
HK Directory is: /data/data17/seq_proc/50006000.007/
!earthevents:ASCA-GIS3-PH > select mkf "FOV==1" data_dir=. ASCA_mkf_def_expr=ft*.mkf
!earthevents:ASCA-GIS3-PH > extract events
!earthevents:ASCA-GIS3-PH > save events outfile=event.tmp use_events=no
Wrote events list to file event.tmp
!earthevents:ASCA-GIS3-PH > exit save_session=no
-> Extracting ad50006000g300470m.brt
** XSELECT V1.3 **
!> Enter session name >[xsel] earthevents
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS PHA_BINS
1 W50 EAST PH MEDIUM 28/04/93 19:50:32 0.99E+04 26610 1024
EXTRACTOR vers 2.0 11 Apr 1997.
Doing file: /data/data17/seq_proc/50006000.007/ad50006000g300470m.unf
Total Good Bad: Region Time Phase Cut
26610 7401 0 19209 0 0
Writing events file
7401 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
26610 7401 0 19209 0 0
in 2191.97 seconds
Command not found; type ? for a command listing
!earthevents:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!earthevents:ASCA > set datadir .
Setting data directory to /data/data17/seq_proc/50006000.007/
Setting mkf directory to /data/data17/seq_proc/50006000.007/
!earthevents:ASCA > read events ad50006000g300470m.unf
Got new instrument: GIS3
Setting: IMAGE binning = 1
WMAP binning = 1
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 1023
Got the minimum time resolution of the read data: 0.50000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data17/seq_proc/50006000.007/
HK Directory is: /data/data17/seq_proc/50006000.007/
!earthevents:ASCA-GIS3-PH > select mkf "FOV==2" data_dir=. ASCA_mkf_def_expr=ft*.mkf
!earthevents:ASCA-GIS3-PH > extract events
!earthevents:ASCA-GIS3-PH > save events outfile=event.tmp use_events=no
Wrote events list to file event.tmp
!earthevents:ASCA-GIS3-PH > exit save_session=no
-> Extracting bright and dark Earth events from ad50006000g300570h.unf
** XSELECT V1.3 **
!> Enter session name >[xsel] earthevents
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS PHA_BINS
1 W50 EAST PH HIGH 28/04/93 22:52:30 0.15E+04 3482 1024
EXTRACTOR vers 2.0 11 Apr 1997.
Skipping file: /data/data17/seq_proc/50006000.007/ad50006000g300570h.unf
Writing events file
0 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
0 0 0 0 0 0
in 0.00 seconds
Command not found; type ? for a command listing
!earthevents:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!earthevents:ASCA > set datadir .
Setting data directory to /data/data17/seq_proc/50006000.007/
Setting mkf directory to /data/data17/seq_proc/50006000.007/
!earthevents:ASCA > read events ad50006000g300570h.unf
Got new instrument: GIS3
Setting: IMAGE binning = 1
WMAP binning = 1
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 1023
Got the minimum time resolution of the read data: 0.62500E-01
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data17/seq_proc/50006000.007/
HK Directory is: /data/data17/seq_proc/50006000.007/
!earthevents:ASCA-GIS3-PH > select mkf "FOV==1" data_dir=. ASCA_mkf_def_expr=ft*.mkf
!earthevents:ASCA-GIS3-PH > extract events
!earthevents:ASCA-GIS3-PH > save events outfile=event.tmp use_events=no
Wrote events list to file event.tmp
!earthevents:ASCA-GIS3-PH > exit save_session=no
-> Deleting ad50006000g300570h.drk since it contains 0 events
** XSELECT V1.3 **
!> Enter session name >[xsel] earthevents
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS PHA_BINS
1 W50 EAST PH HIGH 28/04/93 22:52:30 0.15E+04 3482 1024
EXTRACTOR vers 2.0 11 Apr 1997.
Skipping file: /data/data17/seq_proc/50006000.007/ad50006000g300570h.unf
Writing events file
0 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
0 0 0 0 0 0
in 0.00 seconds
Command not found; type ? for a command listing
!earthevents:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!earthevents:ASCA > set datadir .
Setting data directory to /data/data17/seq_proc/50006000.007/
Setting mkf directory to /data/data17/seq_proc/50006000.007/
!earthevents:ASCA > read events ad50006000g300570h.unf
Got new instrument: GIS3
Setting: IMAGE binning = 1
WMAP binning = 1
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 1023
Got the minimum time resolution of the read data: 0.62500E-01
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data17/seq_proc/50006000.007/
HK Directory is: /data/data17/seq_proc/50006000.007/
!earthevents:ASCA-GIS3-PH > select mkf "FOV==2" data_dir=. ASCA_mkf_def_expr=ft*.mkf
!earthevents:ASCA-GIS3-PH > extract events
!earthevents:ASCA-GIS3-PH > save events outfile=event.tmp use_events=no
Wrote events list to file event.tmp
!earthevents:ASCA-GIS3-PH > exit save_session=no
-> Deleting ad50006000g300570h.brt since it contains 0 eventsOffset of 1.500000000000000E+08 from 1/1/93 0:0:0 is date and time (including leapseconds) = 3/10/97 2:39:56.000000 Modified Julian Day = 50724.111064814816928
ad50006000s000102h.unf|S0CCDPOW|1111|Which S0 CCDs are in use(0123): 0=OFF 1=ON ad50006000s000302h.unf|S0CCDPOW|1011|Which S0 CCDs are in use(0123): 0=OFF 1=ON ad50006000s000602h.unf|S0CCDPOW|1111|Which S0 CCDs are in use(0123): 0=OFF 1=ON ad50006000s000102h.unf|S0CCDMOD|4|How many S0 CCDs are in use: 1, 2, or 4 ad50006000s000302h.unf|S0CCDMOD|2|How many S0 CCDs are in use: 1, 2, or 4 ad50006000s000602h.unf|S0CCDMOD|4|How many S0 CCDs are in use: 1, 2, or 4 ad50006000s000102h.unf|S0CCDLST|0 1 2 3|S0 CCD readout order ad50006000s000302h.unf|S0CCDLST|0 2 2 3|S0 CCD readout order ad50006000s000602h.unf|S0CCDLST|0 1 2 3|S0 CCD readout order ad50006000s000102h.unf|TLM_FILE|ft930427_2350.1950|Name of input telemetry file ad50006000s000302h.unf|TLM_FILE|ft930427_2350.1950|Name of input telemetry file ad50006000s000602h.unf|TLM_FILE|ft930428_1949.2350|Name of input telemetry file-> listing ad50006000s000102h.unf
ad50006000s000202m.unf|TLM_FILE|ft930427_2350.1950|Name of input telemetry file ad50006000s000502m.unf|TLM_FILE|ft930428_1949.2350|Name of input telemetry file-> listing ad50006000s000202m.unf
ad50006000s000112h.unf|S0CCDPOW|1111|Which S0 CCDs are in use(0123): 0=OFF 1=ON ad50006000s000312h.unf|S0CCDPOW|1011|Which S0 CCDs are in use(0123): 0=OFF 1=ON ad50006000s000612h.unf|S0CCDPOW|1111|Which S0 CCDs are in use(0123): 0=OFF 1=ON ad50006000s000112h.unf|S0CCDMOD|4|How many S0 CCDs are in use: 1, 2, or 4 ad50006000s000312h.unf|S0CCDMOD|2|How many S0 CCDs are in use: 1, 2, or 4 ad50006000s000612h.unf|S0CCDMOD|4|How many S0 CCDs are in use: 1, 2, or 4 ad50006000s000112h.unf|S0CCDLST|0 1 2 3|S0 CCD readout order ad50006000s000312h.unf|S0CCDLST|0 2 2 3|S0 CCD readout order ad50006000s000612h.unf|S0CCDLST|0 1 2 3|S0 CCD readout order ad50006000s000112h.unf|TLM_FILE|ft930427_2350.1950|Name of input telemetry file ad50006000s000312h.unf|TLM_FILE|ft930427_2350.1950|Name of input telemetry file ad50006000s000612h.unf|TLM_FILE|ft930428_1949.2350|Name of input telemetry file-> listing ad50006000s000112h.unf
ad50006000s000101h.unf|S0CCDPOW|1111|Which S0 CCDs are in use(0123): 0=OFF 1=ON ad50006000s000301h.unf|S0CCDPOW|1011|Which S0 CCDs are in use(0123): 0=OFF 1=ON ad50006000s000601h.unf|S0CCDPOW|1111|Which S0 CCDs are in use(0123): 0=OFF 1=ON ad50006000s000101h.unf|S0CCDMOD|4|How many S0 CCDs are in use: 1, 2, or 4 ad50006000s000301h.unf|S0CCDMOD|2|How many S0 CCDs are in use: 1, 2, or 4 ad50006000s000601h.unf|S0CCDMOD|4|How many S0 CCDs are in use: 1, 2, or 4 ad50006000s000101h.unf|S0CCDLST|0 1 2 3|S0 CCD readout order ad50006000s000301h.unf|S0CCDLST|0 2 2 3|S0 CCD readout order ad50006000s000601h.unf|S0CCDLST|0 1 2 3|S0 CCD readout order ad50006000s000101h.unf|TLM_FILE|ft930427_2350.1950|Name of input telemetry file ad50006000s000301h.unf|TLM_FILE|ft930427_2350.1950|Name of input telemetry file ad50006000s000601h.unf|TLM_FILE|ft930428_1949.2350|Name of input telemetry file-> listing ad50006000s000101h.unf
ad50006000s100102h.unf|TLM_FILE|ft930427_2350.1950|Name of input telemetry file ad50006000s100402h.unf|TLM_FILE|ft930427_2350.1950|Name of input telemetry file ad50006000s100602h.unf|TLM_FILE|ft930428_1949.2350|Name of input telemetry file ad50006000s100102h.unf|ORIGMODE|FAINT|DATAMODE before any conversion ad50006000s100402h.unf|ORIGMODE|BRIGHT|DATAMODE before any conversion ad50006000s100602h.unf|ORIGMODE|FAINT|DATAMODE before any conversion-> listing ad50006000s100102h.unf
ad50006000s100202m.unf|TLM_FILE|ft930427_2350.1950|Name of input telemetry file ad50006000s100502m.unf|TLM_FILE|ft930428_1949.2350|Name of input telemetry file-> listing ad50006000s100202m.unf
ad50006000s100112h.unf|TLM_FILE|ft930427_2350.1950|Name of input telemetry file ad50006000s100612h.unf|TLM_FILE|ft930428_1949.2350|Name of input telemetry file-> listing ad50006000s100112h.unf
ad50006000s100101h.unf|TLM_FILE|ft930427_2350.1950|Name of input telemetry file ad50006000s100601h.unf|TLM_FILE|ft930428_1949.2350|Name of input telemetry file-> listing ad50006000s100101h.unf
ad50006000g200270h.unf|TLM_FILE|ft930427_2350.1950|Name of input telemetry file ad50006000g200570h.unf|TLM_FILE|ft930428_1949.2350|Name of input telemetry file-> listing ad50006000g200270h.unf
ad50006000g200170m.unf|TLM_FILE|ft930427_2350.1950|Name of input telemetry file ad50006000g200470m.unf|TLM_FILE|ft930428_1949.2350|Name of input telemetry file-> listing ad50006000g200170m.unf
ad50006000g300270h.unf|TLM_FILE|ft930427_2350.1950|Name of input telemetry file ad50006000g300570h.unf|TLM_FILE|ft930428_1949.2350|Name of input telemetry file-> listing ad50006000g300270h.unf
ad50006000g300170m.unf|TLM_FILE|ft930427_2350.1950|Name of input telemetry file ad50006000g300470m.unf|TLM_FILE|ft930428_1949.2350|Name of input telemetry file-> listing ad50006000g300170m.unf
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Doing inventory of all files