The following information is also available:
Time column is TIME ORDERED-> Fetching fa970409_2051.0625.Z
ATTITUDE_V0.9j
reading attitude file:./merged.tmp
open asc output file:out.tmp
AVERAGE ASPECT AND OFFSET FOR THIS ATTITUDE FILE:
Attitude file start and stop ascatime : 134772687.245500 134807112.139900
Data file start and stop ascatime : 134772687.245500 134807112.139900
Aspecting run start and stop ascatime : 134772687.245589 134807112.139817
Time interval averaged over (seconds) : 34424.894227
Total pointing and manuver time (sec) : 23458.476562 10966.485352
Mean boresight Euler angles : 275.461666 103.893755 14.712485
RA DEC SUN ANGLE
Mean solar position (deg) : 17.77 7.54
Mean aberration (arcsec) : 5.19 -3.07
Mean sat X-axis (deg) : 47.903945 -69.870028 80.10
Mean sat Y-axis (deg) : 1.853896 14.272759 17.00
Mean sat Z-axis (deg) : 275.461666 -13.893755 103.68
RA DEC ROLL OFFSET
(deg) (deg) (deg) (arcmin)
Average 275.677460 -13.701692 284.763855 0.057740
Minimum 275.667175 -13.730003 284.757843 0.000000
Maximum 275.685455 -13.690849 284.803589 1.419117
Sigma (RMS) 0.000350 0.000085 0.001229 0.051491
Number of ASPECT records processed = 46380
Aspecting to RA/DEC : 275.67745972 -13.70169163
closing output file...
closing attitude file...
-> Standard Error Output From FTOOL attitudeATTITUDE_V0.9j : Detected gap > 15min in attitude file: 134777630.73050 ATTITUDE_V0.9j : Detected gap > 15min in attitude file:-> Standard Output From STOOL checkatt:
Opening file: ./out.tmp
***************** Observation Info ******************
RA (J2000 deg): 275.677 DEC: -13.702
START TIME: SC 134772687.2456 = UT 09/04/97 20:51:27
****** Definition of Attitude SENSOR Bit Flags ******
Sensors used in the attitude determination and attitude control mode
1: USED, 0: NOT USED
B0:STT-A, B1:STT-B, B2:NSAS, B3:GAS, B4:SSAS-SA, B5:SSAS-SB,
B6:IRU-X, B7:IRU-Y, B8:IRU-Z, B9:IRU-S1, B10:IRU-S2,
B11: Attitude control mode 1: coarse, 0: fine
B12: Sun presence 1: day, 0: night
B13: STT-A earth occultation 1: earth occultation, 0: no occultation
B14: STT-B earth occultation 1: earth occultation, 0: no occultation
B16,17,18: STT-A track stars no.1,2,3, 1: USED, 0: NOT USED
B19,20,21: STT-B track stars no.1,2,3, 1: USED, 0: NOT USED
B22,23: always 0
******** Attitude File Reconstruction Summary *******
S S N G S S I I I I I A S S S S S
T T S A S S R R R R R C U T T T T
T T A S A A U U U U U M N T T T T
- - S . A A - - - - - . . - - - -
A B . . - - X Y Z S S . . A B A B
. . . . S S . . . 1 2 . . O O S S
offset_time separation sensor . . . . A B . . . . . . . C C T T
(sec) (arcmin) . . . . . . . . . . . . . C C R R
BIT: 0 1 2 3 4 5 6 7 8 9 A B C D E
12.000065 1.260 8003 1 1 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
75.999802 0.817 8803 1 1 0 0 0 0 0 0 0 0 0 1 0 0 0 0 0
2269.993164 0.100 8003 1 1 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
11561.964844 0.019 8803 1 1 0 0 0 0 0 0 0 0 0 1 0 0 0 0 0
13755.958008 0.012 D080C3 1 1 0 0 0 0 1 1 0 0 0 0 0 0 0 0 2
17305.947266 0.088 8803 1 1 0 0 0 0 0 0 0 0 0 1 0 0 0 0 0
19499.939453 0.015 8003 1 1 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
23049.929688 0.012 8803 1 1 0 0 0 0 0 0 0 0 0 1 0 0 0 0 0
25243.921875 0.051 D880C3 1 1 0 0 0 0 1 1 0 0 0 0 0 0 0 0 3
28793.912109 0.059 8803 1 1 0 0 0 0 0 0 0 0 0 1 0 0 0 0 0
30987.904297 0.069 8003 1 1 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
34422.394531 0.186 9003 1 1 0 0 0 0 0 0 0 0 0 0 1 0 0 0 0
34424.894531 0.800 9003 1 1 0 0 0 0 0 0 0 0 0 0 1 0 0 0 0
Attitude Records: 46380
Attitude Steps: 13
Maneuver ACM time: 10966.5 sec
Pointed ACM time: 23458.5 sec
-> Calculating aspect point100 97 count=46309 sum1=1.27563e+07 sum2=4.81121e+06 sum3=681314 100 98 count=47 sum1=12946.6 sum2=4883.27 sum3=692.068 100 99 count=17 sum1=4682.77 sum2=1766.46 sum3=250.573 100 100 count=2 sum1=550.908 sum2=207.832 sum3=29.479 101 96 count=1 sum1=275.47 sum2=103.883 sum3=14.721 101 97 count=3 sum1=826.399 sum2=311.672 sum3=44.145 0 out of 46379 points outside bin structure-> Euler angles: 275.461, 103.894, 14.7124
frf_directory,s,h,"./",,,"frf directory" frf_file,s,h,"ft970409_2051.0625",,,"frf telemetry file"-> Standard Output From FTOOL frfread:
Frfread version 3.00 patch 32 ASCA format Telemetry file: ft970409_2051.0625 Initial mode = 2 (Bright) Initial value for dummy = 0 Initial datamode = 0 (Observation) Initial sis = 0 Initial bit_rate = 2 Reading all superframes reading PH mode reading PCAL mode reading MPCmode No mode = 0 Faint = 653696 Bright = 24128 Fast = 0 Frame = 64512 Dark frame = 0 Histogram = 0 Integration = 0 PH = 742336 MPC = 0 PCAL = 0 Memory Check = 0 Number of superframes = 11628 no. of SIS events found = 1212947-> Standard Error Output From FTOOL frfread
coordinate error 0 48-> Removing the following files with NEVENTS=0
ft970409_2051_0625G200370H.fits ft970409_2051_0625G200470H.fits ft970409_2051_0625G200570M.fits ft970409_2051_0625G200670H.fits ft970409_2051_0625G200770H.fits ft970409_2051_0625G200970H.fits ft970409_2051_0625G201170H.fits ft970409_2051_0625G201270M.fits ft970409_2051_0625G201370H.fits ft970409_2051_0625G201470H.fits ft970409_2051_0625G201670H.fits ft970409_2051_0625G201870H.fits ft970409_2051_0625G201999.fits ft970409_2051_0625G202070H.fits ft970409_2051_0625G202170H.fits ft970409_2051_0625G202599.fits ft970409_2051_0625G202770H.fits ft970409_2051_0625G202870H.fits ft970409_2051_0625G202970M.fits ft970409_2051_0625G203070H.fits ft970409_2051_0625G203170H.fits ft970409_2051_0625G203270H.fits ft970409_2051_0625G203599.fits ft970409_2051_0625G203770H.fits ft970409_2051_0625G203870H.fits ft970409_2051_0625G203970M.fits ft970409_2051_0625G204070H.fits ft970409_2051_0625G204170H.fits ft970409_2051_0625G204370H.fits ft970409_2051_0625G300370H.fits ft970409_2051_0625G300470H.fits ft970409_2051_0625G300570M.fits ft970409_2051_0625G300670H.fits ft970409_2051_0625G301370H.fits ft970409_2051_0625G301470H.fits ft970409_2051_0625G301570M.fits ft970409_2051_0625G301670H.fits ft970409_2051_0625G302170H.fits ft970409_2051_0625G302270H.fits ft970409_2051_0625G302399.fits ft970409_2051_0625G302470H.fits ft970409_2051_0625G302999.fits ft970409_2051_0625G303170H.fits ft970409_2051_0625G303270H.fits ft970409_2051_0625G303370M.fits ft970409_2051_0625G303470H.fits ft970409_2051_0625G303570H.fits ft970409_2051_0625G303670H.fits ft970409_2051_0625G303999.fits ft970409_2051_0625G304170H.fits ft970409_2051_0625G304270H.fits ft970409_2051_0625G304370M.fits ft970409_2051_0625G304470H.fits ft970409_2051_0625G304570H.fits ft970409_2051_0625S000402H.fits ft970409_2051_0625S001202H.fits ft970409_2051_0625S002001H.fits ft970409_2051_0625S002399.fits ft970409_2051_0625S002401H.fits ft970409_2051_0625S002799.fits ft970409_2051_0625S003004H.fits ft970409_2051_0625S003201M.fits ft970409_2051_0625S003402M.fits ft970409_2051_0625S003899.fits ft970409_2051_0625S004101H.fits ft970409_2051_0625S004301M.fits ft970409_2051_0625S100402H.fits ft970409_2051_0625S100802H.fits ft970409_2051_0625S101404H.fits ft970409_2051_0625S101799.fits ft970409_2051_0625S101801H.fits ft970409_2051_0625S102099.fits ft970409_2051_0625S102301M.fits ft970409_2051_0625S102502M.fits ft970409_2051_0625S102899.fits ft970409_2051_0625S103004H.fits ft970409_2051_0625S103201M.fits-> Checking for empty GTI extensions
ft970409_2051_0625S000102M.fits[3] ft970409_2051_0625S000201M.fits[3] ft970409_2051_0625S000301H.fits[3] ft970409_2051_0625S000502M.fits[3] ft970409_2051_0625S000601M.fits[3] ft970409_2051_0625S000701H.fits[3] ft970409_2051_0625S000801H.fits[3] ft970409_2051_0625S000901H.fits[3] ft970409_2051_0625S001001H.fits[3] ft970409_2051_0625S001101H.fits[3] ft970409_2051_0625S001302M.fits[3] ft970409_2051_0625S001402M.fits[3] ft970409_2051_0625S001502M.fits[3] ft970409_2051_0625S001601M.fits[3] ft970409_2051_0625S001701H.fits[3] ft970409_2051_0625S001801H.fits[3] ft970409_2051_0625S001901H.fits[3] ft970409_2051_0625S002101H.fits[3] ft970409_2051_0625S002201H.fits[3] ft970409_2051_0625S002501H.fits[3] ft970409_2051_0625S002601H.fits[3] ft970409_2051_0625S002801H.fits[3] ft970409_2051_0625S002901H.fits[3] ft970409_2051_0625S003101H.fits[3] ft970409_2051_0625S003302M.fits[3] ft970409_2051_0625S003502M.fits[3] ft970409_2051_0625S003601H.fits[3] ft970409_2051_0625S003701H.fits[3] ft970409_2051_0625S003901H.fits[3] ft970409_2051_0625S004001H.fits[3] ft970409_2051_0625S004201H.fits[3] ft970409_2051_0625S004402M.fits[3] ft970409_2051_0625S004502M.fits[3] ft970409_2051_0625S004602M.fits[3] ft970409_2051_0625S004701H.fits[3] ft970409_2051_0625S004801H.fits[3] ft970409_2051_0625S004901H.fits[3]-> Merging GTIs from the following files:
ft970409_2051_0625S100102M.fits[3] ft970409_2051_0625S100201M.fits[3] ft970409_2051_0625S100301H.fits[3] ft970409_2051_0625S100502M.fits[3] ft970409_2051_0625S100601M.fits[3] ft970409_2051_0625S100701H.fits[3] ft970409_2051_0625S100902M.fits[3] ft970409_2051_0625S101002M.fits[3] ft970409_2051_0625S101102M.fits[3] ft970409_2051_0625S101201M.fits[3] ft970409_2051_0625S101301H.fits[3] ft970409_2051_0625S101501H.fits[3] ft970409_2051_0625S101601H.fits[3] ft970409_2051_0625S101901H.fits[3] ft970409_2051_0625S102101H.fits[3] ft970409_2051_0625S102201H.fits[3] ft970409_2051_0625S102402M.fits[3] ft970409_2051_0625S102602M.fits[3] ft970409_2051_0625S102701H.fits[3] ft970409_2051_0625S102901H.fits[3] ft970409_2051_0625S103101H.fits[3] ft970409_2051_0625S103302M.fits[3] ft970409_2051_0625S103402M.fits[3] ft970409_2051_0625S103502M.fits[3] ft970409_2051_0625S103601H.fits[3]-> Merging GTIs from the following files:
ft970409_2051_0625G200170M.fits[3] ft970409_2051_0625G200270H.fits[3] ft970409_2051_0625G200870H.fits[3] ft970409_2051_0625G201070H.fits[3] ft970409_2051_0625G201570H.fits[3] ft970409_2051_0625G201770H.fits[3] ft970409_2051_0625G202270H.fits[3] ft970409_2051_0625G202370H.fits[3] ft970409_2051_0625G202470H.fits[3] ft970409_2051_0625G202670H.fits[3] ft970409_2051_0625G203370H.fits[3] ft970409_2051_0625G203470H.fits[3] ft970409_2051_0625G203670H.fits[3] ft970409_2051_0625G204270H.fits[3] ft970409_2051_0625G204470H.fits[3]-> Merging GTIs from the following files:
ft970409_2051_0625G300170M.fits[3] ft970409_2051_0625G300270H.fits[3] ft970409_2051_0625G300770H.fits[3] ft970409_2051_0625G300870H.fits[3] ft970409_2051_0625G300970H.fits[3] ft970409_2051_0625G301070H.fits[3] ft970409_2051_0625G301170H.fits[3] ft970409_2051_0625G301270H.fits[3] ft970409_2051_0625G301770H.fits[3] ft970409_2051_0625G301870H.fits[3] ft970409_2051_0625G301970H.fits[3] ft970409_2051_0625G302070H.fits[3] ft970409_2051_0625G302570H.fits[3] ft970409_2051_0625G302670H.fits[3] ft970409_2051_0625G302770H.fits[3] ft970409_2051_0625G302870H.fits[3] ft970409_2051_0625G303070H.fits[3] ft970409_2051_0625G303770H.fits[3] ft970409_2051_0625G303870H.fits[3] ft970409_2051_0625G304070H.fits[3] ft970409_2051_0625G304670H.fits[3] ft970409_2051_0625G304770H.fits[3] ft970409_2051_0625G304870H.fits[3]
GISSORTCODE:LO:Start program GISSORTCODE:LO:End program-> Standard Error Output From STOOL gissortsplit:
GISSORTSPLIT:LO:Start program GISSORTSPLIT:LO:g200170h.prelist merge count = 4 photon cnt = 8 GISSORTSPLIT:LO:g200270h.prelist merge count = 2 photon cnt = 6 GISSORTSPLIT:LO:g200370h.prelist merge count = 8 photon cnt = 19577 GISSORTSPLIT:LO:g200170m.prelist merge count = 1 photon cnt = 379 GISSORTSPLIT:LO:Total filenames split = 15 GISSORTSPLIT:LO:Total split file cnt = 4 GISSORTSPLIT:LO:End program-> Creating ad55000030g200170h.unf
---- cmerge: version 1.5 ---- A total of 8 fits files ...... Sorting files using KEY: TSTART ... Checking GTI overlap in input files ... Merging binary extension #: 1 1 -- ft970409_2051_0625G200270H.fits 2 -- ft970409_2051_0625G201070H.fits 3 -- ft970409_2051_0625G201770H.fits 4 -- ft970409_2051_0625G202470H.fits 5 -- ft970409_2051_0625G202670H.fits 6 -- ft970409_2051_0625G203470H.fits 7 -- ft970409_2051_0625G203670H.fits 8 -- ft970409_2051_0625G204470H.fits Merging binary extension #: 2 1 -- ft970409_2051_0625G200270H.fits 2 -- ft970409_2051_0625G201070H.fits 3 -- ft970409_2051_0625G201770H.fits 4 -- ft970409_2051_0625G202470H.fits 5 -- ft970409_2051_0625G202670H.fits 6 -- ft970409_2051_0625G203470H.fits 7 -- ft970409_2051_0625G203670H.fits 8 -- ft970409_2051_0625G204470H.fits Checking the output file ... Extention # 1 ...... OK Extention # 2 ...... OK The program appears to have finished successfully!-> Ignoring the following files containing 000000379 events
ft970409_2051_0625G200170M.fits-> Ignoring the following files containing 000000008 events
ft970409_2051_0625G200870H.fits ft970409_2051_0625G201570H.fits ft970409_2051_0625G202270H.fits ft970409_2051_0625G204270H.fits-> Ignoring the following files containing 000000006 events
ft970409_2051_0625G202370H.fits ft970409_2051_0625G203370H.fits-> Collecting GIS3 event files by mode
GISSORTCODE:LO:Start program GISSORTCODE:LO:End program-> Standard Error Output From STOOL gissortsplit:
GISSORTSPLIT:LO:Start program GISSORTSPLIT:LO:g300170h.prelist merge count = 3 photon cnt = 6 GISSORTSPLIT:LO:g300270h.prelist merge count = 4 photon cnt = 9 GISSORTSPLIT:LO:g300370h.prelist merge count = 5 photon cnt = 12 GISSORTSPLIT:LO:g300470h.prelist merge count = 9 photon cnt = 18594 GISSORTSPLIT:LO:g300570h.prelist merge count = 1 photon cnt = 6 GISSORTSPLIT:LO:g300170m.prelist merge count = 1 photon cnt = 328 GISSORTSPLIT:LO:Total filenames split = 23 GISSORTSPLIT:LO:Total split file cnt = 6 GISSORTSPLIT:LO:End program-> Creating ad55000030g300170h.unf
---- cmerge: version 1.5 ---- A total of 9 fits files ...... Sorting files using KEY: TSTART ... Checking GTI overlap in input files ... Merging binary extension #: 1 1 -- ft970409_2051_0625G300270H.fits 2 -- ft970409_2051_0625G301070H.fits 3 -- ft970409_2051_0625G301270H.fits 4 -- ft970409_2051_0625G302070H.fits 5 -- ft970409_2051_0625G302870H.fits 6 -- ft970409_2051_0625G303070H.fits 7 -- ft970409_2051_0625G303870H.fits 8 -- ft970409_2051_0625G304070H.fits 9 -- ft970409_2051_0625G304870H.fits Merging binary extension #: 2 1 -- ft970409_2051_0625G300270H.fits 2 -- ft970409_2051_0625G301070H.fits 3 -- ft970409_2051_0625G301270H.fits 4 -- ft970409_2051_0625G302070H.fits 5 -- ft970409_2051_0625G302870H.fits 6 -- ft970409_2051_0625G303070H.fits 7 -- ft970409_2051_0625G303870H.fits 8 -- ft970409_2051_0625G304070H.fits 9 -- ft970409_2051_0625G304870H.fits Checking the output file ... Extention # 1 ...... OK Extention # 2 ...... OK The program appears to have finished successfully!-> Ignoring the following files containing 000000328 events
ft970409_2051_0625G300170M.fits-> Ignoring the following files containing 000000012 events
ft970409_2051_0625G300970H.fits ft970409_2051_0625G301970H.fits ft970409_2051_0625G302770H.fits ft970409_2051_0625G303770H.fits ft970409_2051_0625G304770H.fits-> Ignoring the following files containing 000000009 events
ft970409_2051_0625G300870H.fits ft970409_2051_0625G301870H.fits ft970409_2051_0625G302670H.fits ft970409_2051_0625G304670H.fits-> Ignoring the following files containing 000000006 events
ft970409_2051_0625G301170H.fits-> Ignoring the following files containing 000000006 events
ft970409_2051_0625G300770H.fits ft970409_2051_0625G301770H.fits ft970409_2051_0625G302570H.fits-> Collecting SIS0 event files by mode
SIS0SORTCODE:LO:Start program SIS0SORTCODE:LO:End program-> Standard Error Output From STOOL sis0sortsplit:
SIS0SORTSPLIT:LO:Start program SIS0SORTSPLIT:LO:s000101h.prelist merge count = 15 photon cnt = 149999 SIS0SORTSPLIT:LO:s000201h.prelist merge count = 8 photon cnt = 354722 SIS0SORTSPLIT:LO:s000301h.prelist merge count = 1 photon cnt = 209 SIS0SORTSPLIT:LO:s000401m.prelist merge count = 3 photon cnt = 96 SIS0SORTSPLIT:LO:s000502m.prelist merge count = 8 photon cnt = 16157 SIS0SORTSPLIT:LO:s000602m.prelist merge count = 2 photon cnt = 68 SIS0SORTSPLIT:LO:Total filenames split = 37 SIS0SORTSPLIT:LO:Total split file cnt = 6 SIS0SORTSPLIT:LO:End program-> Creating ad55000030s000101h.unf
---- cmerge: version 1.5 ---- A total of 8 fits files ...... Sorting files using KEY: TSTART ... Checking GTI overlap in input files ... Merging binary extension #: 1 1 -- ft970409_2051_0625S000801H.fits 2 -- ft970409_2051_0625S001001H.fits 3 -- ft970409_2051_0625S001801H.fits 4 -- ft970409_2051_0625S002601H.fits 5 -- ft970409_2051_0625S002801H.fits 6 -- ft970409_2051_0625S003701H.fits 7 -- ft970409_2051_0625S003901H.fits 8 -- ft970409_2051_0625S004801H.fits Merging binary extension #: 2 1 -- ft970409_2051_0625S000801H.fits 2 -- ft970409_2051_0625S001001H.fits 3 -- ft970409_2051_0625S001801H.fits 4 -- ft970409_2051_0625S002601H.fits 5 -- ft970409_2051_0625S002801H.fits 6 -- ft970409_2051_0625S003701H.fits 7 -- ft970409_2051_0625S003901H.fits 8 -- ft970409_2051_0625S004801H.fits Checking the output file ... Extention # 1 ...... OK Extention # 2 ...... OK The program appears to have finished successfully!-> Creating ad55000030s000201h.unf
---- cmerge: version 1.5 ---- A total of 15 fits files ...... Sorting files using KEY: TSTART ... Checking GTI overlap in input files ... Merging binary extension #: 1 1 -- ft970409_2051_0625S000301H.fits 2 -- ft970409_2051_0625S000701H.fits 3 -- ft970409_2051_0625S000901H.fits 4 -- ft970409_2051_0625S001101H.fits 5 -- ft970409_2051_0625S001701H.fits 6 -- ft970409_2051_0625S001901H.fits 7 -- ft970409_2051_0625S002101H.fits 8 -- ft970409_2051_0625S002501H.fits 9 -- ft970409_2051_0625S002901H.fits 10 -- ft970409_2051_0625S003101H.fits 11 -- ft970409_2051_0625S003601H.fits 12 -- ft970409_2051_0625S004001H.fits 13 -- ft970409_2051_0625S004201H.fits 14 -- ft970409_2051_0625S004701H.fits 15 -- ft970409_2051_0625S004901H.fits Merging binary extension #: 2 1 -- ft970409_2051_0625S000301H.fits 2 -- ft970409_2051_0625S000701H.fits 3 -- ft970409_2051_0625S000901H.fits 4 -- ft970409_2051_0625S001101H.fits 5 -- ft970409_2051_0625S001701H.fits 6 -- ft970409_2051_0625S001901H.fits 7 -- ft970409_2051_0625S002101H.fits 8 -- ft970409_2051_0625S002501H.fits 9 -- ft970409_2051_0625S002901H.fits 10 -- ft970409_2051_0625S003101H.fits 11 -- ft970409_2051_0625S003601H.fits 12 -- ft970409_2051_0625S004001H.fits 13 -- ft970409_2051_0625S004201H.fits 14 -- ft970409_2051_0625S004701H.fits 15 -- ft970409_2051_0625S004901H.fits Checking the output file ... Extention # 1 ...... OK Extention # 2 ...... OK The program appears to have finished successfully!-> Creating ad55000030s000302m.unf
---- cmerge: version 1.5 ---- A total of 8 fits files ...... Sorting files using KEY: TSTART ... Checking GTI overlap in input files ... Merging binary extension #: 1 1 -- ft970409_2051_0625S000102M.fits 2 -- ft970409_2051_0625S000502M.fits 3 -- ft970409_2051_0625S001302M.fits 4 -- ft970409_2051_0625S001502M.fits 5 -- ft970409_2051_0625S003302M.fits 6 -- ft970409_2051_0625S003502M.fits 7 -- ft970409_2051_0625S004402M.fits 8 -- ft970409_2051_0625S004602M.fits Merging binary extension #: 2 1 -- ft970409_2051_0625S000102M.fits 2 -- ft970409_2051_0625S000502M.fits 3 -- ft970409_2051_0625S001302M.fits 4 -- ft970409_2051_0625S001502M.fits 5 -- ft970409_2051_0625S003302M.fits 6 -- ft970409_2051_0625S003502M.fits 7 -- ft970409_2051_0625S004402M.fits 8 -- ft970409_2051_0625S004602M.fits Checking the output file ... Extention # 1 ...... OK Extention # 2 ...... OK The program appears to have finished successfully!-> Ignoring the following files containing 000000209 events
ft970409_2051_0625S002201H.fits-> Ignoring the following files containing 000000096 events
ft970409_2051_0625S000201M.fits ft970409_2051_0625S000601M.fits ft970409_2051_0625S001601M.fits-> Ignoring the following files containing 000000068 events
ft970409_2051_0625S001402M.fits ft970409_2051_0625S004502M.fits-> Collecting SIS1 event files by mode
SIS1SORTCODE:LO:Start program SIS1SORTCODE:LO:End program-> Standard Error Output From STOOL sis1sortsplit:
SIS1SORTSPLIT:LO:Start program SIS1SORTSPLIT:LO:s100101h.prelist merge count = 10 photon cnt = 581215 SIS1SORTSPLIT:LO:s100201h.prelist merge count = 1 photon cnt = 91209 SIS1SORTSPLIT:LO:s100301h.prelist merge count = 1 photon cnt = 256 SIS1SORTSPLIT:LO:s100401m.prelist merge count = 3 photon cnt = 96 SIS1SORTSPLIT:LO:s100502m.prelist merge count = 8 photon cnt = 18867 SIS1SORTSPLIT:LO:s100602m.prelist merge count = 2 photon cnt = 52 SIS1SORTSPLIT:LO:Total filenames split = 25 SIS1SORTSPLIT:LO:Total split file cnt = 6 SIS1SORTSPLIT:LO:End program-> Creating ad55000030s100101h.unf
---- cmerge: version 1.5 ---- A total of 10 fits files ...... Sorting files using KEY: TSTART ... Checking GTI overlap in input files ... Merging binary extension #: 1 1 -- ft970409_2051_0625S100301H.fits 2 -- ft970409_2051_0625S100701H.fits 3 -- ft970409_2051_0625S101301H.fits 4 -- ft970409_2051_0625S101501H.fits 5 -- ft970409_2051_0625S101901H.fits 6 -- ft970409_2051_0625S102201H.fits 7 -- ft970409_2051_0625S102701H.fits 8 -- ft970409_2051_0625S102901H.fits 9 -- ft970409_2051_0625S103101H.fits 10 -- ft970409_2051_0625S103601H.fits Merging binary extension #: 2 1 -- ft970409_2051_0625S100301H.fits 2 -- ft970409_2051_0625S100701H.fits 3 -- ft970409_2051_0625S101301H.fits 4 -- ft970409_2051_0625S101501H.fits 5 -- ft970409_2051_0625S101901H.fits 6 -- ft970409_2051_0625S102201H.fits 7 -- ft970409_2051_0625S102701H.fits 8 -- ft970409_2051_0625S102901H.fits 9 -- ft970409_2051_0625S103101H.fits 10 -- ft970409_2051_0625S103601H.fits Checking the output file ... Extention # 1 ...... OK Extention # 2 ...... OK The program appears to have finished successfully!-> Checking ft970409_2051_0625S102101H.fits
---- cmerge: version 1.5 ---- A total of 1 fits files ...... Sorting files using KEY: TSTART ... Checking GTI overlap in input files ... Merging binary extension #: 1 1 -- ft970409_2051_0625S102101H.fits Merging binary extension #: 2 1 -- ft970409_2051_0625S102101H.fits Checking the output file ... Extention # 1 ...... OK Extention # 2 ...... OK The program appears to have finished successfully!-> Creating ad55000030s100302m.unf
---- cmerge: version 1.5 ---- A total of 8 fits files ...... Sorting files using KEY: TSTART ... Checking GTI overlap in input files ... Merging binary extension #: 1 1 -- ft970409_2051_0625S100102M.fits 2 -- ft970409_2051_0625S100502M.fits 3 -- ft970409_2051_0625S100902M.fits 4 -- ft970409_2051_0625S101102M.fits 5 -- ft970409_2051_0625S102402M.fits 6 -- ft970409_2051_0625S102602M.fits 7 -- ft970409_2051_0625S103302M.fits 8 -- ft970409_2051_0625S103502M.fits Merging binary extension #: 2 1 -- ft970409_2051_0625S100102M.fits 2 -- ft970409_2051_0625S100502M.fits 3 -- ft970409_2051_0625S100902M.fits 4 -- ft970409_2051_0625S101102M.fits 5 -- ft970409_2051_0625S102402M.fits 6 -- ft970409_2051_0625S102602M.fits 7 -- ft970409_2051_0625S103302M.fits 8 -- ft970409_2051_0625S103502M.fits Checking the output file ... Extention # 1 ...... OK Extention # 2 ...... OK The program appears to have finished successfully!-> Ignoring the following files containing 000000256 events
ft970409_2051_0625S101601H.fits-> Ignoring the following files containing 000000096 events
ft970409_2051_0625S100201M.fits ft970409_2051_0625S100601M.fits ft970409_2051_0625S101201M.fits-> Ignoring the following files containing 000000052 events
ft970409_2051_0625S101002M.fits ft970409_2051_0625S103402M.fits-> Tar-ing together the leftover raw files
a ft970409_2051_0625G200170M.fits 48K a ft970409_2051_0625G200870H.fits 40K a ft970409_2051_0625G201570H.fits 40K a ft970409_2051_0625G202270H.fits 40K a ft970409_2051_0625G202370H.fits 40K a ft970409_2051_0625G203370H.fits 40K a ft970409_2051_0625G204270H.fits 40K a ft970409_2051_0625G300170M.fits 48K a ft970409_2051_0625G300770H.fits 40K a ft970409_2051_0625G300870H.fits 40K a ft970409_2051_0625G300970H.fits 40K a ft970409_2051_0625G301170H.fits 40K a ft970409_2051_0625G301770H.fits 40K a ft970409_2051_0625G301870H.fits 40K a ft970409_2051_0625G301970H.fits 40K a ft970409_2051_0625G302570H.fits 40K a ft970409_2051_0625G302670H.fits 40K a ft970409_2051_0625G302770H.fits 40K a ft970409_2051_0625G303770H.fits 40K a ft970409_2051_0625G304670H.fits 40K a ft970409_2051_0625G304770H.fits 40K a ft970409_2051_0625S000201M.fits 40K a ft970409_2051_0625S000601M.fits 40K a ft970409_2051_0625S001402M.fits 40K a ft970409_2051_0625S001601M.fits 40K a ft970409_2051_0625S002201H.fits 45K a ft970409_2051_0625S004502M.fits 40K a ft970409_2051_0625S100201M.fits 40K a ft970409_2051_0625S100601M.fits 40K a ft970409_2051_0625S101002M.fits 40K a ft970409_2051_0625S101201M.fits 40K a ft970409_2051_0625S101601H.fits 48K a ft970409_2051_0625S103402M.fits 40K-> Checking OBJECT keywords in HK and event files
temp2gain v4.2 opening ft970409_2051.0625 'ft970409_2051.0625' is successfully opened Data Start Time is 134772684.25 (970409 205124) Time Margin 2.0 sec included Sync error detected in 879 th SF Sync error detected in 881 th SF Sync error detected in 955 th SF Sync error detected in 956 th SF Sync error detected in 957 th SF Sync error detected in 3534 th SF 'ft970409_2051.0625' EOF detected, sf=11628 Data End Time is 134807114.14 (970410 062514) Gain History is written in ft970409_2051_0625.ghf-> Checking if column CAL_START in ft970409_2051_0625.ghf[1] is in order
Time column is TIME ORDERED-> Checking if column CAL_STOP in ft970409_2051_0625.ghf[1] is in order
Time column is TIME ORDERED
ASCALIN_V0.9t-> Standard Error Output From FTOOL ascalin
ASCALIN_V0.9t : Detected gap > 15min in attitude file: 134777630.73050 ASCALIN_V0.9t : Detected gap > 15min in attitude file:-> Checking if ad55000030g300170h.unf is covered by attitude file
ASCALIN_V0.9t-> Standard Error Output From FTOOL ascalin
ASCALIN_V0.9t : Detected gap > 15min in attitude file: 134777630.73050 ASCALIN_V0.9t : Detected gap > 15min in attitude file:-> Checking if ad55000030s000101h.unf is covered by attitude file
ASCALIN_V0.9t-> Standard Error Output From FTOOL ascalin
ASCALIN_V0.9t : Detected gap > 15min in attitude file: 134777630.73050 ASCALIN_V0.9t : Detected gap > 15min in attitude file:-> Checking if ad55000030s000102h.unf is covered by attitude file
ASCALIN_V0.9t-> Standard Error Output From FTOOL ascalin
ASCALIN_V0.9t : Detected gap > 15min in attitude file: 134777630.73050 ASCALIN_V0.9t : Detected gap > 15min in attitude file:-> Checking if ad55000030s000112h.unf is covered by attitude file
ASCALIN_V0.9t-> Standard Error Output From FTOOL ascalin
ASCALIN_V0.9t : Detected gap > 15min in attitude file: 134777630.73050 ASCALIN_V0.9t : Detected gap > 15min in attitude file:-> Checking if ad55000030s000201h.unf is covered by attitude file
ASCALIN_V0.9t-> Standard Error Output From FTOOL ascalin
ASCALIN_V0.9t : Detected gap > 15min in attitude file: 134777630.73050 ASCALIN_V0.9t : Detected gap > 15min in attitude file:-> Checking if ad55000030s000202h.unf is covered by attitude file
ASCALIN_V0.9t-> Standard Error Output From FTOOL ascalin
ASCALIN_V0.9t : Detected gap > 15min in attitude file: 134777630.73050 ASCALIN_V0.9t : Detected gap > 15min in attitude file:-> Checking if ad55000030s000212h.unf is covered by attitude file
ASCALIN_V0.9t-> Standard Error Output From FTOOL ascalin
ASCALIN_V0.9t : Detected gap > 15min in attitude file: 134777630.73050 ASCALIN_V0.9t : Detected gap > 15min in attitude file:-> Checking if ad55000030s000302m.unf is covered by attitude file
ASCALIN_V0.9t-> Standard Error Output From FTOOL ascalin
ASCALIN_V0.9t : Detected gap > 15min in attitude file: 134777630.73050 ASCALIN_V0.9t : Detected gap > 15min in attitude file:-> Checking if ad55000030s100101h.unf is covered by attitude file
ASCALIN_V0.9t-> Standard Error Output From FTOOL ascalin
ASCALIN_V0.9t : Detected gap > 15min in attitude file: 134777630.73050 ASCALIN_V0.9t : Detected gap > 15min in attitude file:-> Checking if ad55000030s100102h.unf is covered by attitude file
ASCALIN_V0.9t-> Standard Error Output From FTOOL ascalin
ASCALIN_V0.9t : Detected gap > 15min in attitude file: 134777630.73050 ASCALIN_V0.9t : Detected gap > 15min in attitude file:-> Checking if ad55000030s100112h.unf is covered by attitude file
ASCALIN_V0.9t-> Standard Error Output From FTOOL ascalin
ASCALIN_V0.9t : Detected gap > 15min in attitude file: 134777630.73050 ASCALIN_V0.9t : Detected gap > 15min in attitude file:-> Checking if ad55000030s100201h.unf is covered by attitude file
ASCALIN_V0.9t-> Checking if ad55000030s100202h.unf is covered by attitude file
ASCALIN_V0.9t-> Checking if ad55000030s100212h.unf is covered by attitude file
ASCALIN_V0.9t-> Checking if ad55000030s100302m.unf is covered by attitude file
ASCALIN_V0.9t-> Standard Error Output From FTOOL ascalin
ASCALIN_V0.9t : Detected gap > 15min in attitude file: 134777630.73050 ASCALIN_V0.9t : Detected gap > 15min in attitude file:
Date and time are: 97/ 4/ 9 20:51 mjd=50547.868750 Orbit file name is ./frf.orbit.214 Epoch of Orbital Elements: 1997/4/7 9:59:59 Rigidity Data File: ./rigidity.data.1.23 Attitude FRF: fa970409_2051.0625 S0-HK file: ft970409_2051_0625S0HK.fits S1-HK file: ft970409_2051_0625S1HK.fits G2-HK file: ft970409_2051_0625G2HK.fits G3-HK file: ft970409_2051_0625G3HK.fits output FITS File: ft970409_2051_0625.mkf Total 1076 Data bins were processed.-> Checking if column TIME in ft970409_2051_0625.mkf is in order
Time column is TIME ORDERED-> Calculating dead time values for filter file
The sum of the selected column is 14461.482 The mean of the selected column is 903.84264 The standard deviation of the selected column is 452.59887 The minimum of selected column is 355.43860 The maximum of selected column is 1713.0990 The number of points used in calculation is 16-> Standard Output From FTOOL fstatistic:
The sum of the selected column is 12479.851 The mean of the selected column is 779.99069 The standard deviation of the selected column is 431.97362 The minimum of selected column is 305.37595 The maximum of selected column is 1566.5049 The number of points used in calculation is 16-> Standard Output From FTOOL fstatistic:
The sum of the selected column is 13940.168 The mean of the selected column is 871.26052 The standard deviation of the selected column is 503.75832 The minimum of selected column is 348.65732 The maximum of selected column is 1847.8495 The number of points used in calculation is 16-> Standard Output From FTOOL fstatistic:
The sum of the selected column is 12430.476 The mean of the selected column is 776.90475 The standard deviation of the selected column is 446.79161 The minimum of selected column is 269.06332 The maximum of selected column is 1558.1611 The number of points used in calculation is 16-> Using the following selection criteria:
(SAA==0) &&(BR_EARTH>20) &&(ELV>10) &&(COR>6) &&(ACS==0) &&(ANG_DIST>0)&& (ANG_DIST<0.01) &&(FOV==0) && ( (S0_PIXL0>0.0 && S0_PIXL0<2261.6 )&& (S0_PIXL1>0.0 && S0_PIXL1<2075.9 )&& (S0_PIXL2>0.0 && S0_PIXL2<2382.5 )&& (S0_PIXL3>0.0 && S0_PIXL3<2117.2 ) ) &&( (S0_SATF0<1) ||(S0_SATF0>1)) &&( (S0_SATF1<1) ||(S0_SATF1>1)) &&( (S0_SATF2<1) ||(S0_SATF2>1)) &&( (S0_SATF3<1) ||(S0_SATF3>1)) &&((T_DY_NT<0)||(T_DY_NT>64)) &&((T_SAA <0)||(T_SAA >64))-> Standard Output From FTOOL xselect:
** XSELECT V1.3 **
!> Enter session name >[xsel] screen
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS S0CCDPOW
1 GAL_RIDG BRIGHT HIGH 09/04/97 21:55:34 0.79E+04 6058 1111
Processing file: /data/data16/seq_proc/55000030.005/ad55000030s000102h.unf
EXTRACTOR vers 2.0 11 Apr 1997.
Doing file: /data/data16/seq_proc/55000030.005/screen_work1001.xsl
Total Good Bad: Region Time Phase Cut
2235 1098 0 1137 0 0
Writing events file
1098 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
2235 1098 0 1137 0 0
in 414.24 seconds
CLEANSIS_V1.6
allocating image arrays...
PROGRAM TO MAKE AN SIS SCIENCE FILE CLEANED OF ANOMALOUS PIXELS.
* Anomalous pixels may consist of at least two populations.
1. Persistent HOT pixels are removed by comparing to the chip mean.
2. Flickering WARM pixels are removed by comparing to the cell mean.
3. In faint areas (zero bgd), flickering pixels are removed with a
cutoff threshold.
Hints:
Choose cell size and thresholds based on the expected background and the PSF.
Use the DIRTYSIS option to examine the anomalous pixel spectra.
Try a multiple pass clean:
Choose a PHA cut to optimize the S/N of the flickering pixels,
then a broad band clean.
Be suspicious of extended source cleans.
For very bright sources you may need to turn off the iteration option.
See the help page for further info (fhelp cleansis)
Poisson clean cell size : 5
Poisson probability threshold : 0.631E-05
Zero Bgd Cutoff threshold (>) : 3
Iterate : T
Dirtysis : F
Minimum PHA value (inclusive) : 0
Maximum PHA value (inclusive) : 4095
open output file: /data/data16/seq_proc/55000030.005/screen_in_event.xsl
reading data file: /data/data16/seq_proc/55000030.005/screen_out_event.xsl
copying primary header to output file...
making chip image...
Total counts in chip images : 1098
copy bad pix array...
cleaning chip # 0
Hot pixels & counts : 22 273
Flickering pixels iter, pixels & cnts : 1 11 49
cleaning chip # 1
Hot pixels & counts : 21 328
Flickering pixels iter, pixels & cnts : 1 13 57
cleaning chip # 2
Hot pixels & counts : 2 10
cleaning chip # 3
Hot pixels & counts : 18 211
Flickering pixels iter, pixels & cnts : 1 8 33
Number of pixels rejected : 95
Number of (internal) image counts : 1098
Number of image cts rejected (N, %) : 961 87.5227661
By chip : 0 1 2 3
Pixels rejected : 33 34 2 26
Image counts : 377 429 22 270
Image cts rejected: 322 385 10 244
Image cts rej (%) : 85.41 89.74 45.45 90.37
filtering data...
Total counts : 377 429 22 270
Total cts rejected: 322 385 10 244
Total cts rej (%) : 85.41 89.74 45.45 90.37
Number of clean counts accepted : 137
writing history cards...
copying extensions...
writing out hot pixs...
Number of rejected pixels : 95
updating NEVENTS keywords...
closing data file...
closing clean file...
Command not found; type ? for a command listing
!screen:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!screen:ASCA > set datadir .
Setting data directory to /data/data16/seq_proc/55000030.005/
Setting mkf directory to /data/data16/seq_proc/55000030.005/
!screen:ASCA > read events ad55000030s000102h.unf
Got new instrument: SIS0
Setting: IMAGE binning = 4
WMAP binning = 8
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 2047
Got the minimum time resolution of the read data: 16.000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data16/seq_proc/55000030.005/
HK Directory is: /data/data16/seq_proc/55000030.005/
!screen:ASCA-SIS0-BRIGHT > select event "grade==0||grade==2||grade==3||grade==4" save_file=no
!screen:ASCA-SIS0-BRIGHT > select mkf "@criteria.tmp" data_dir=. ASCA_mkf_def_expr=ft*.mkf
!screen:ASCA-SIS0-BRIGHT > extract events
!screen:ASCA-SIS0-BRIGHT > sisclean saoimage=no sis_plot=no clean=2 cellsize=5 log_prob=-5.24 bkg_thr=3 clean_phalow=0 clean_phahi=4095
!screen:ASCA-SIS0-BRIGHT > save clean outfile=ad55000030s000102h.evt use_events=no
Wrote cleaned events file to ad55000030s000102h.evt
!screen:ASCA-SIS0-BRIGHT > exit save_session=no
-> Filtering ad55000030s000112h.unf into ad55000030s000112h.evtThe sum of the selected column is 14461.482 The mean of the selected column is 903.84264 The standard deviation of the selected column is 452.59887 The minimum of selected column is 355.43860 The maximum of selected column is 1713.0990 The number of points used in calculation is 16-> Standard Output From FTOOL fstatistic:
The sum of the selected column is 12479.851 The mean of the selected column is 779.99069 The standard deviation of the selected column is 431.97362 The minimum of selected column is 305.37595 The maximum of selected column is 1566.5049 The number of points used in calculation is 16-> Standard Output From FTOOL fstatistic:
The sum of the selected column is 13940.168 The mean of the selected column is 871.26052 The standard deviation of the selected column is 503.75832 The minimum of selected column is 348.65732 The maximum of selected column is 1847.8495 The number of points used in calculation is 16-> Standard Output From FTOOL fstatistic:
The sum of the selected column is 12430.476 The mean of the selected column is 776.90475 The standard deviation of the selected column is 446.79161 The minimum of selected column is 269.06332 The maximum of selected column is 1558.1611 The number of points used in calculation is 16-> Using the following selection criteria:
(SAA==0) &&(BR_EARTH>20) &&(ELV>10) &&(COR>6) &&(ACS==0) &&(ANG_DIST>0)&& (ANG_DIST<0.01) &&(FOV==0) && ( (S0_PIXL0>0.0 && S0_PIXL0<2261.6 )&& (S0_PIXL1>0.0 && S0_PIXL1<2075.9 )&& (S0_PIXL2>0.0 && S0_PIXL2<2382.5 )&& (S0_PIXL3>0.0 && S0_PIXL3<2117.2 ) ) &&( (S0_SATF0<1) ||(S0_SATF0>1)) &&( (S0_SATF1<1) ||(S0_SATF1>1)) &&( (S0_SATF2<1) ||(S0_SATF2>1)) &&( (S0_SATF3<1) ||(S0_SATF3>1)) &&((T_DY_NT<0)||(T_DY_NT>64)) &&((T_SAA <0)||(T_SAA >64))-> Standard Output From FTOOL xselect:
** XSELECT V1.3 **
!> Enter session name >[xsel] screen
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS S0CCDPOW
1 GAL_RIDG BRIGHT2 HIGH 09/04/97 21:55:34 0.79E+04 9285 1111
Processing file: /data/data16/seq_proc/55000030.005/ad55000030s000112h.unf
EXTRACTOR vers 2.0 11 Apr 1997.
Doing file: /data/data16/seq_proc/55000030.005/screen_work1001.xsl
Total Good Bad: Region Time Phase Cut
4096 1882 0 2214 0 0
Writing events file
1882 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
4096 1882 0 2214 0 0
in 414.24 seconds
CLEANSIS_V1.6
allocating image arrays...
PROGRAM TO MAKE AN SIS SCIENCE FILE CLEANED OF ANOMALOUS PIXELS.
* Anomalous pixels may consist of at least two populations.
1. Persistent HOT pixels are removed by comparing to the chip mean.
2. Flickering WARM pixels are removed by comparing to the cell mean.
3. In faint areas (zero bgd), flickering pixels are removed with a
cutoff threshold.
Hints:
Choose cell size and thresholds based on the expected background and the PSF.
Use the DIRTYSIS option to examine the anomalous pixel spectra.
Try a multiple pass clean:
Choose a PHA cut to optimize the S/N of the flickering pixels,
then a broad band clean.
Be suspicious of extended source cleans.
For very bright sources you may need to turn off the iteration option.
See the help page for further info (fhelp cleansis)
Poisson clean cell size : 5
Poisson probability threshold : 0.631E-05
Zero Bgd Cutoff threshold (>) : 3
Iterate : T
Dirtysis : F
Minimum PHA value (inclusive) : 0
Maximum PHA value (inclusive) : 4095
open output file: /data/data16/seq_proc/55000030.005/screen_in_event.xsl
reading data file: /data/data16/seq_proc/55000030.005/screen_out_event.xsl
copying primary header to output file...
making chip image...
Total counts in chip images : 1882
copy bad pix array...
cleaning chip # 0
Hot pixels & counts : 35 546
Flickering pixels iter, pixels & cnts : 1 30 148
cleaning chip # 1
Hot pixels & counts : 29 524
Flickering pixels iter, pixels & cnts : 1 19 101
cleaning chip # 2
Hot pixels & counts : 5 20
cleaning chip # 3
Hot pixels & counts : 24 358
Flickering pixels iter, pixels & cnts : 1 9 34
Number of pixels rejected : 151
Number of (internal) image counts : 1882
Number of image cts rejected (N, %) : 1731 91.9766235
By chip : 0 1 2 3
Pixels rejected : 65 48 5 33
Image counts : 742 669 38 433
Image cts rejected: 694 625 20 392
Image cts rej (%) : 93.53 93.42 52.63 90.53
filtering data...
Total counts : 742 669 38 433
Total cts rejected: 694 625 20 392
Total cts rej (%) : 93.53 93.42 52.63 90.53
Number of clean counts accepted : 151
writing history cards...
copying extensions...
writing out hot pixs...
Number of rejected pixels : 151
updating NEVENTS keywords...
closing data file...
closing clean file...
Command not found; type ? for a command listing
!screen:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!screen:ASCA > set datadir .
Setting data directory to /data/data16/seq_proc/55000030.005/
Setting mkf directory to /data/data16/seq_proc/55000030.005/
!screen:ASCA > read events ad55000030s000112h.unf
Got new instrument: SIS0
Setting: IMAGE binning = 4
WMAP binning = 8
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 4095
Got the minimum time resolution of the read data: 16.000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data16/seq_proc/55000030.005/
HK Directory is: /data/data16/seq_proc/55000030.005/
!screen:ASCA-SIS0-BRIGHT2 > select event "grade==0||grade==2||grade==3||grade==4" save_file=no
!screen:ASCA-SIS0-BRIGHT2 > select mkf "@criteria.tmp" data_dir=. ASCA_mkf_def_expr=ft*.mkf
!screen:ASCA-SIS0-BRIGHT2 > extract events
!screen:ASCA-SIS0-BRIGHT2 > sisclean saoimage=no sis_plot=no clean=2 cellsize=5 log_prob=-5.24 bkg_thr=3 clean_phalow=0 clean_phahi=4095
!screen:ASCA-SIS0-BRIGHT2 > save clean outfile=ad55000030s000112h.evt use_events=no
Wrote cleaned events file to ad55000030s000112h.evt
!screen:ASCA-SIS0-BRIGHT2 > exit save_session=no
-> Skipping ad55000030s000201h.unf because of modeThe sum of the selected column is 57326.077 The mean of the selected column is 262.96366 The standard deviation of the selected column is 198.97961 The minimum of selected column is 118.93787 The maximum of selected column is 1241.0977 The number of points used in calculation is 218-> Standard Output From FTOOL fstatistic:
The sum of the selected column is 46927.655 The mean of the selected column is 215.26447 The standard deviation of the selected column is 173.30662 The minimum of selected column is 25.187576 The maximum of selected column is 1101.3472 The number of points used in calculation is 218-> Standard Output From FTOOL fstatistic:
The sum of the selected column is 64959.721 The mean of the selected column is 297.98037 The standard deviation of the selected column is 324.94223 The minimum of selected column is 89.750275 The maximum of selected column is 1887.0996 The number of points used in calculation is 218-> Standard Output From FTOOL fstatistic:
The sum of the selected column is 46731.868 The mean of the selected column is 214.36637 The standard deviation of the selected column is 204.27338 The minimum of selected column is 82.687759 The maximum of selected column is 1242.9727 The number of points used in calculation is 218-> Using the following selection criteria:
(SAA==0) &&(BR_EARTH>20) &&(ELV>10) &&(COR>6) &&(ACS==0) &&(ANG_DIST>0)&& (ANG_DIST<0.01) &&(FOV==0) && ( (S0_PIXL0>0.0 && S0_PIXL0<859.9 )&& (S0_PIXL1>0.0 && S0_PIXL1<735.1 )&& (S0_PIXL2>0.0 && S0_PIXL2<1272.8 )&& (S0_PIXL3>0.0 && S0_PIXL3<827.1 ) ) &&( (S0_SATF0<1) ||(S0_SATF0>1)) &&( (S0_SATF1<1) ||(S0_SATF1>1)) &&( (S0_SATF2<1) ||(S0_SATF2>1)) &&( (S0_SATF3<1) ||(S0_SATF3>1)) &&((T_DY_NT<0)||(T_DY_NT>64)) &&((T_SAA <0)||(T_SAA >64))-> Standard Output From FTOOL xselect:
** XSELECT V1.3 **
!> Enter session name >[xsel] screen
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS S0CCDPOW
1 GAL_RIDG BRIGHT HIGH 09/04/97 21:02:58 0.11E+05 79486 1111
Processing file: /data/data16/seq_proc/55000030.005/ad55000030s000202h.unf
EXTRACTOR vers 2.0 11 Apr 1997.
Doing file: /data/data16/seq_proc/55000030.005/screen_work1001.xsl
Total Good Bad: Region Time Phase Cut
41939 25604 0 16335 0 0
Writing events file
25604 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
41939 25604 0 16335 0 0
in 6489.46 seconds
CLEANSIS_V1.6
allocating image arrays...
PROGRAM TO MAKE AN SIS SCIENCE FILE CLEANED OF ANOMALOUS PIXELS.
* Anomalous pixels may consist of at least two populations.
1. Persistent HOT pixels are removed by comparing to the chip mean.
2. Flickering WARM pixels are removed by comparing to the cell mean.
3. In faint areas (zero bgd), flickering pixels are removed with a
cutoff threshold.
Hints:
Choose cell size and thresholds based on the expected background and the PSF.
Use the DIRTYSIS option to examine the anomalous pixel spectra.
Try a multiple pass clean:
Choose a PHA cut to optimize the S/N of the flickering pixels,
then a broad band clean.
Be suspicious of extended source cleans.
For very bright sources you may need to turn off the iteration option.
See the help page for further info (fhelp cleansis)
Poisson clean cell size : 5
Poisson probability threshold : 0.631E-05
Zero Bgd Cutoff threshold (>) : 3
Iterate : T
Dirtysis : F
Minimum PHA value (inclusive) : 0
Maximum PHA value (inclusive) : 4095
open output file: /data/data16/seq_proc/55000030.005/screen_in_event.xsl
reading data file: /data/data16/seq_proc/55000030.005/screen_out_event.xsl
copying primary header to output file...
making chip image...
Total counts in chip images : 25604
copy bad pix array...
cleaning chip # 0
Hot pixels & counts : 53 8292
Flickering pixels iter, pixels & cnts : 1 31 309
cleaning chip # 1
Hot pixels & counts : 30 5589
Flickering pixels iter, pixels & cnts : 1 24 213
cleaning chip # 2
Hot pixels & counts : 25 4605
Flickering pixels iter, pixels & cnts : 1 12 92
cleaning chip # 3
Hot pixels & counts : 28 5350
Flickering pixels iter, pixels & cnts : 1 12 132
Number of pixels rejected : 215
Number of (internal) image counts : 25604
Number of image cts rejected (N, %) : 24582 96.0084381
By chip : 0 1 2 3
Pixels rejected : 84 54 37 40
Image counts : 8847 6102 4907 5748
Image cts rejected: 8601 5802 4697 5482
Image cts rej (%) : 97.22 95.08 95.72 95.37
filtering data...
Total counts : 8847 6102 4907 5748
Total cts rejected: 8601 5802 4697 5482
Total cts rej (%) : 97.22 95.08 95.72 95.37
Number of clean counts accepted : 1022
writing history cards...
copying extensions...
writing out hot pixs...
Number of rejected pixels : 215
updating NEVENTS keywords...
closing data file...
closing clean file...
Command not found; type ? for a command listing
!screen:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!screen:ASCA > set datadir .
Setting data directory to /data/data16/seq_proc/55000030.005/
Setting mkf directory to /data/data16/seq_proc/55000030.005/
!screen:ASCA > read events ad55000030s000202h.unf
Got new instrument: SIS0
Setting: IMAGE binning = 4
WMAP binning = 8
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 2047
Got the minimum time resolution of the read data: 16.000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data16/seq_proc/55000030.005/
HK Directory is: /data/data16/seq_proc/55000030.005/
!screen:ASCA-SIS0-BRIGHT > select event "grade==0||grade==2||grade==3||grade==4" save_file=no
!screen:ASCA-SIS0-BRIGHT > select mkf "@criteria.tmp" data_dir=. ASCA_mkf_def_expr=ft*.mkf
!screen:ASCA-SIS0-BRIGHT > extract events
!screen:ASCA-SIS0-BRIGHT > sisclean saoimage=no sis_plot=no clean=2 cellsize=5 log_prob=-5.24 bkg_thr=3 clean_phalow=0 clean_phahi=4095
!screen:ASCA-SIS0-BRIGHT > save clean outfile=ad55000030s000202h.evt use_events=no
Wrote cleaned events file to ad55000030s000202h.evt
!screen:ASCA-SIS0-BRIGHT > exit save_session=no
-> Filtering ad55000030s000212h.unf into ad55000030s000212h.evtThe sum of the selected column is 57326.077 The mean of the selected column is 262.96366 The standard deviation of the selected column is 198.97961 The minimum of selected column is 118.93787 The maximum of selected column is 1241.0977 The number of points used in calculation is 218-> Standard Output From FTOOL fstatistic:
The sum of the selected column is 46927.655 The mean of the selected column is 215.26447 The standard deviation of the selected column is 173.30662 The minimum of selected column is 25.187576 The maximum of selected column is 1101.3472 The number of points used in calculation is 218-> Standard Output From FTOOL fstatistic:
The sum of the selected column is 64959.721 The mean of the selected column is 297.98037 The standard deviation of the selected column is 324.94223 The minimum of selected column is 89.750275 The maximum of selected column is 1887.0996 The number of points used in calculation is 218-> Standard Output From FTOOL fstatistic:
The sum of the selected column is 46731.868 The mean of the selected column is 214.36637 The standard deviation of the selected column is 204.27338 The minimum of selected column is 82.687759 The maximum of selected column is 1242.9727 The number of points used in calculation is 218-> Using the following selection criteria:
(SAA==0) &&(BR_EARTH>20) &&(ELV>10) &&(COR>6) &&(ACS==0) &&(ANG_DIST>0)&& (ANG_DIST<0.01) &&(FOV==0) && ( (S0_PIXL0>0.0 && S0_PIXL0<859.9 )&& (S0_PIXL1>0.0 && S0_PIXL1<735.1 )&& (S0_PIXL2>0.0 && S0_PIXL2<1272.8 )&& (S0_PIXL3>0.0 && S0_PIXL3<827.1 ) ) &&( (S0_SATF0<1) ||(S0_SATF0>1)) &&( (S0_SATF1<1) ||(S0_SATF1>1)) &&( (S0_SATF2<1) ||(S0_SATF2>1)) &&( (S0_SATF3<1) ||(S0_SATF3>1)) &&((T_DY_NT<0)||(T_DY_NT>64)) &&((T_SAA <0)||(T_SAA >64))-> Standard Output From FTOOL xselect:
** XSELECT V1.3 **
!> Enter session name >[xsel] screen
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS S0CCDPOW
1 GAL_RIDG BRIGHT2 HIGH 09/04/97 21:02:58 0.11E+05 91162 1111
Processing file: /data/data16/seq_proc/55000030.005/ad55000030s000212h.unf
EXTRACTOR vers 2.0 11 Apr 1997.
Doing file: /data/data16/seq_proc/55000030.005/screen_work1001.xsl
Total Good Bad: Region Time Phase Cut
59147 35965 0 23182 0 0
Writing events file
35965 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
59147 35965 0 23182 0 0
in 6489.46 seconds
CLEANSIS_V1.6
allocating image arrays...
PROGRAM TO MAKE AN SIS SCIENCE FILE CLEANED OF ANOMALOUS PIXELS.
* Anomalous pixels may consist of at least two populations.
1. Persistent HOT pixels are removed by comparing to the chip mean.
2. Flickering WARM pixels are removed by comparing to the cell mean.
3. In faint areas (zero bgd), flickering pixels are removed with a
cutoff threshold.
Hints:
Choose cell size and thresholds based on the expected background and the PSF.
Use the DIRTYSIS option to examine the anomalous pixel spectra.
Try a multiple pass clean:
Choose a PHA cut to optimize the S/N of the flickering pixels,
then a broad band clean.
Be suspicious of extended source cleans.
For very bright sources you may need to turn off the iteration option.
See the help page for further info (fhelp cleansis)
Poisson clean cell size : 5
Poisson probability threshold : 0.631E-05
Zero Bgd Cutoff threshold (>) : 3
Iterate : T
Dirtysis : F
Minimum PHA value (inclusive) : 0
Maximum PHA value (inclusive) : 4095
open output file: /data/data16/seq_proc/55000030.005/screen_in_event.xsl
reading data file: /data/data16/seq_proc/55000030.005/screen_out_event.xsl
copying primary header to output file...
making chip image...
Total counts in chip images : 35965
copy bad pix array...
cleaning chip # 0
Hot pixels & counts : 58 13267
Flickering pixels iter, pixels & cnts : 1 32 549
cleaning chip # 1
Hot pixels & counts : 30 7372
Flickering pixels iter, pixels & cnts : 1 25 383
cleaning chip # 2
Hot pixels & counts : 26 6314
Flickering pixels iter, pixels & cnts : 1 14 202
cleaning chip # 3
Hot pixels & counts : 29 6212
Flickering pixels iter, pixels & cnts : 1 17 202
Number of pixels rejected : 231
Number of (internal) image counts : 35965
Number of image cts rejected (N, %) : 34501 95.9293747
By chip : 0 1 2 3
Pixels rejected : 90 55 40 46
Image counts : 14172 8172 6829 6792
Image cts rejected: 13816 7755 6516 6414
Image cts rej (%) : 97.49 94.90 95.42 94.43
filtering data...
Total counts : 14172 8172 6829 6792
Total cts rejected: 13816 7755 6516 6414
Total cts rej (%) : 97.49 94.90 95.42 94.43
Number of clean counts accepted : 1464
writing history cards...
copying extensions...
writing out hot pixs...
Number of rejected pixels : 231
updating NEVENTS keywords...
closing data file...
closing clean file...
Command not found; type ? for a command listing
!screen:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!screen:ASCA > set datadir .
Setting data directory to /data/data16/seq_proc/55000030.005/
Setting mkf directory to /data/data16/seq_proc/55000030.005/
!screen:ASCA > read events ad55000030s000212h.unf
Got new instrument: SIS0
Setting: IMAGE binning = 4
WMAP binning = 8
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 4095
Got the minimum time resolution of the read data: 16.000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data16/seq_proc/55000030.005/
HK Directory is: /data/data16/seq_proc/55000030.005/
!screen:ASCA-SIS0-BRIGHT2 > select event "grade==0||grade==2||grade==3||grade==4" save_file=no
!screen:ASCA-SIS0-BRIGHT2 > select mkf "@criteria.tmp" data_dir=. ASCA_mkf_def_expr=ft*.mkf
!screen:ASCA-SIS0-BRIGHT2 > extract events
!screen:ASCA-SIS0-BRIGHT2 > sisclean saoimage=no sis_plot=no clean=2 cellsize=5 log_prob=-5.24 bkg_thr=3 clean_phalow=0 clean_phahi=4095
!screen:ASCA-SIS0-BRIGHT2 > save clean outfile=ad55000030s000212h.evt use_events=no
Wrote cleaned events file to ad55000030s000212h.evt
!screen:ASCA-SIS0-BRIGHT2 > exit save_session=no
-> Filtering ad55000030s000302m.unf into ad55000030s000302m.evt(SAA==0) &&(BR_EARTH>20) &&(ELV>10) &&(COR>6) &&(ACS==0) &&(ANG_DIST>0)&& (ANG_DIST<0.01) &&(FOV==0) && ( (S0_PIXL0>0)&& (S0_PIXL1>0)&& (S0_PIXL2>0)&& (S0_PIXL3>0) ) &&( (S0_SATF0<1) ||(S0_SATF0>1)) &&( (S0_SATF1<1) ||(S0_SATF1>1)) &&( (S0_SATF2<1) ||(S0_SATF2>1)) &&( (S0_SATF3<1) ||(S0_SATF3>1)) &&((T_DY_NT<0)||(T_DY_NT>64)) &&((T_SAA <0)||(T_SAA >64))-> Standard Output From FTOOL xselect:
** XSELECT V1.3 **
!> Enter session name >[xsel] screen
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS S0CCDPOW
1 GAL_RIDG BRIGHT MEDIUM 09/04/97 20:51:26 0.24E+04 16157 1111
Processing file: /data/data16/seq_proc/55000030.005/ad55000030s000302m.unf
EXTRACTOR vers 2.0 11 Apr 1997.
Doing file: /data/data16/seq_proc/55000030.005/screen_work1001.xsl
Total Good Bad: Region Time Phase Cut
7379 284 0 7095 0 0
Writing events file
284 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
7379 284 0 7095 0 0
in 80.00 seconds
CLEANSIS_V1.6
allocating image arrays...
PROGRAM TO MAKE AN SIS SCIENCE FILE CLEANED OF ANOMALOUS PIXELS.
* Anomalous pixels may consist of at least two populations.
1. Persistent HOT pixels are removed by comparing to the chip mean.
2. Flickering WARM pixels are removed by comparing to the cell mean.
3. In faint areas (zero bgd), flickering pixels are removed with a
cutoff threshold.
Hints:
Choose cell size and thresholds based on the expected background and the PSF.
Use the DIRTYSIS option to examine the anomalous pixel spectra.
Try a multiple pass clean:
Choose a PHA cut to optimize the S/N of the flickering pixels,
then a broad band clean.
Be suspicious of extended source cleans.
For very bright sources you may need to turn off the iteration option.
See the help page for further info (fhelp cleansis)
Poisson clean cell size : 5
Poisson probability threshold : 0.631E-05
Zero Bgd Cutoff threshold (>) : 3
Iterate : T
Dirtysis : F
Minimum PHA value (inclusive) : 0
Maximum PHA value (inclusive) : 4095
open output file: /data/data16/seq_proc/55000030.005/screen_in_event.xsl
reading data file: /data/data16/seq_proc/55000030.005/screen_out_event.xsl
copying primary header to output file...
making chip image...
Total counts in chip images : 284
copy bad pix array...
cleaning chip # 0
Hot pixels & counts : 9 36
Flickering pixels iter, pixels & cnts : 1 5 15
cleaning chip # 1
Hot pixels & counts : 9 50
Flickering pixels iter, pixels & cnts : 1 2 6
cleaning chip # 2
Hot pixels & counts : 5 22
Flickering pixels iter, pixels & cnts : 1 2 6
cleaning chip # 3
Hot pixels & counts : 14 66
Flickering pixels iter, pixels & cnts : 1 2 6
Number of pixels rejected : 48
Number of (internal) image counts : 284
Number of image cts rejected (N, %) : 207 72.8873215
By chip : 0 1 2 3
Pixels rejected : 14 11 7 16
Image counts : 81 72 42 89
Image cts rejected: 51 56 28 72
Image cts rej (%) : 62.96 77.78 66.67 80.90
filtering data...
Total counts : 81 72 42 89
Total cts rejected: 51 56 28 72
Total cts rej (%) : 62.96 77.78 66.67 80.90
Number of clean counts accepted : 77
writing history cards...
copying extensions...
writing out hot pixs...
Number of rejected pixels : 48
updating NEVENTS keywords...
closing data file...
closing clean file...
Command not found; type ? for a command listing
!screen:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!screen:ASCA > set datadir .
Setting data directory to /data/data16/seq_proc/55000030.005/
Setting mkf directory to /data/data16/seq_proc/55000030.005/
!screen:ASCA > read events ad55000030s000302m.unf
Got new instrument: SIS0
Setting: IMAGE binning = 4
WMAP binning = 8
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 2047
Got the minimum time resolution of the read data: 16.000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data16/seq_proc/55000030.005/
HK Directory is: /data/data16/seq_proc/55000030.005/
!screen:ASCA-SIS0-BRIGHT > select event "grade==0||grade==2||grade==3||grade==4" save_file=no
!screen:ASCA-SIS0-BRIGHT > select mkf "@criteria.tmp" data_dir=. ASCA_mkf_def_expr=ft*.mkf
!screen:ASCA-SIS0-BRIGHT > extract events
!screen:ASCA-SIS0-BRIGHT > sisclean saoimage=no sis_plot=no clean=2 cellsize=5 log_prob=-5.24 bkg_thr=3 clean_phalow=0 clean_phahi=4095
!screen:ASCA-SIS0-BRIGHT > save clean outfile=ad55000030s000302m.evt use_events=no
Wrote cleaned events file to ad55000030s000302m.evt
!screen:ASCA-SIS0-BRIGHT > exit save_session=no
-> Skipping ad55000030s100101h.unf because of modeThe sum of the selected column is 101920.07 The mean of the selected column is 437.42521 The standard deviation of the selected column is 121.19484 The minimum of selected column is 52.284882 The maximum of selected column is 931.97156 The number of points used in calculation is 233-> Standard Output From FTOOL fstatistic:
The sum of the selected column is 101601.07 The mean of the selected column is 436.05611 The standard deviation of the selected column is 136.18638 The minimum of selected column is 111.12534 The maximum of selected column is 991.22174 The number of points used in calculation is 233-> Standard Output From FTOOL fstatistic:
The sum of the selected column is 86444.717 The mean of the selected column is 371.00737 The standard deviation of the selected column is 120.68819 The minimum of selected column is 89.906532 The maximum of selected column is 985.15924 The number of points used in calculation is 233-> Standard Output From FTOOL fstatistic:
The sum of the selected column is 87794.581 The mean of the selected column is 376.80078 The standard deviation of the selected column is 117.38088 The minimum of selected column is 142.78169 The maximum of selected column is 1054.4407 The number of points used in calculation is 233-> Using the following selection criteria:
(SAA==0) &&(BR_EARTH>20) &&(ELV>10) &&(COR>6) &&(ACS==0) &&(ANG_DIST>0)&& (ANG_DIST<0.01) &&(FOV==0) && ( (S1_PIXL0>73.8 && S1_PIXL0<801 )&& (S1_PIXL1>27.4 && S1_PIXL1<844.6 )&& (S1_PIXL2>8.9 && S1_PIXL2<733 )&& (S1_PIXL3>24.6 && S1_PIXL3<728.9 ) ) &&( (S1_SATF2<1) ||(S1_SATF2>1)) &&( (S1_SATF3<1) ||(S1_SATF3>1)) &&( (S1_SATF0<1) ||(S1_SATF0>1)) &&( (S1_SATF1<1) ||(S1_SATF1>1)) &&((T_DY_NT<0)||(T_DY_NT>64)) &&((T_SAA <0)||(T_SAA >64))-> Standard Output From FTOOL xselect:
** XSELECT V1.3 **
!> Enter session name >[xsel] screen
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS S1CCDPOW
1 GAL_RIDG BRIGHT HIGH 09/04/97 21:02:58 0.17E+05 148330 1111
Processing file: /data/data16/seq_proc/55000030.005/ad55000030s100102h.unf
EXTRACTOR vers 2.0 11 Apr 1997.
Doing file: /data/data16/seq_proc/55000030.005/screen_work1001.xsl
Total Good Bad: Region Time Phase Cut
58410 34517 0 23893 0 0
Writing events file
34517 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
58410 34517 0 23893 0 0
in 7007.70 seconds
CLEANSIS_V1.6
allocating image arrays...
PROGRAM TO MAKE AN SIS SCIENCE FILE CLEANED OF ANOMALOUS PIXELS.
* Anomalous pixels may consist of at least two populations.
1. Persistent HOT pixels are removed by comparing to the chip mean.
2. Flickering WARM pixels are removed by comparing to the cell mean.
3. In faint areas (zero bgd), flickering pixels are removed with a
cutoff threshold.
Hints:
Choose cell size and thresholds based on the expected background and the PSF.
Use the DIRTYSIS option to examine the anomalous pixel spectra.
Try a multiple pass clean:
Choose a PHA cut to optimize the S/N of the flickering pixels,
then a broad band clean.
Be suspicious of extended source cleans.
For very bright sources you may need to turn off the iteration option.
See the help page for further info (fhelp cleansis)
Poisson clean cell size : 5
Poisson probability threshold : 0.631E-05
Zero Bgd Cutoff threshold (>) : 3
Iterate : T
Dirtysis : F
Minimum PHA value (inclusive) : 0
Maximum PHA value (inclusive) : 4095
open output file: /data/data16/seq_proc/55000030.005/screen_in_event.xsl
reading data file: /data/data16/seq_proc/55000030.005/screen_out_event.xsl
copying primary header to output file...
making chip image...
Total counts in chip images : 34517
copy bad pix array...
cleaning chip # 0
Hot pixels & counts : 52 9169
Flickering pixels iter, pixels & cnts : 1 29 452
cleaning chip # 1
Hot pixels & counts : 52 10547
Flickering pixels iter, pixels & cnts : 1 34 632
cleaning chip # 2
Hot pixels & counts : 41 7506
Flickering pixels iter, pixels & cnts : 1 43 424
cleaning chip # 3
Hot pixels & counts : 44 4657
Flickering pixels iter, pixels & cnts : 1 30 390
Number of pixels rejected : 325
Number of (internal) image counts : 34517
Number of image cts rejected (N, %) : 33777 97.8561325
By chip : 0 1 2 3
Pixels rejected : 81 86 84 74
Image counts : 9736 11454 8174 5153
Image cts rejected: 9621 11179 7930 5047
Image cts rej (%) : 98.82 97.60 97.01 97.94
filtering data...
Total counts : 9736 11454 8174 5153
Total cts rejected: 9621 11179 7930 5047
Total cts rej (%) : 98.82 97.60 97.01 97.94
Number of clean counts accepted : 740
writing history cards...
copying extensions...
writing out hot pixs...
Number of rejected pixels : 325
updating NEVENTS keywords...
closing data file...
closing clean file...
Command not found; type ? for a command listing
!screen:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!screen:ASCA > set datadir .
Setting data directory to /data/data16/seq_proc/55000030.005/
Setting mkf directory to /data/data16/seq_proc/55000030.005/
!screen:ASCA > read events ad55000030s100102h.unf
Got new instrument: SIS1
Setting: IMAGE binning = 4
WMAP binning = 8
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 2047
Got the minimum time resolution of the read data: 16.000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data16/seq_proc/55000030.005/
HK Directory is: /data/data16/seq_proc/55000030.005/
!screen:ASCA-SIS1-BRIGHT > select event "grade==0||grade==2||grade==3||grade==4" save_file=no
!screen:ASCA-SIS1-BRIGHT > select mkf "@criteria.tmp" data_dir=. ASCA_mkf_def_expr=ft*.mkf
!screen:ASCA-SIS1-BRIGHT > extract events
!screen:ASCA-SIS1-BRIGHT > sisclean saoimage=no sis_plot=no clean=2 cellsize=5 log_prob=-5.24 bkg_thr=3 clean_phalow=0 clean_phahi=4095
!screen:ASCA-SIS1-BRIGHT > save clean outfile=ad55000030s100102h.evt use_events=no
Wrote cleaned events file to ad55000030s100102h.evt
!screen:ASCA-SIS1-BRIGHT > exit save_session=no
-> Filtering ad55000030s100112h.unf into ad55000030s100112h.evtThe sum of the selected column is 101920.07 The mean of the selected column is 437.42521 The standard deviation of the selected column is 121.19484 The minimum of selected column is 52.284882 The maximum of selected column is 931.97156 The number of points used in calculation is 233-> Standard Output From FTOOL fstatistic:
The sum of the selected column is 101601.07 The mean of the selected column is 436.05611 The standard deviation of the selected column is 136.18638 The minimum of selected column is 111.12534 The maximum of selected column is 991.22174 The number of points used in calculation is 233-> Standard Output From FTOOL fstatistic:
The sum of the selected column is 86444.717 The mean of the selected column is 371.00737 The standard deviation of the selected column is 120.68819 The minimum of selected column is 89.906532 The maximum of selected column is 985.15924 The number of points used in calculation is 233-> Standard Output From FTOOL fstatistic:
The sum of the selected column is 87794.581 The mean of the selected column is 376.80078 The standard deviation of the selected column is 117.38088 The minimum of selected column is 142.78169 The maximum of selected column is 1054.4407 The number of points used in calculation is 233-> Using the following selection criteria:
(SAA==0) &&(BR_EARTH>20) &&(ELV>10) &&(COR>6) &&(ACS==0) &&(ANG_DIST>0)&& (ANG_DIST<0.01) &&(FOV==0) && ( (S1_PIXL0>73.8 && S1_PIXL0<801 )&& (S1_PIXL1>27.4 && S1_PIXL1<844.6 )&& (S1_PIXL2>8.9 && S1_PIXL2<733 )&& (S1_PIXL3>24.6 && S1_PIXL3<728.9 ) ) &&( (S1_SATF2<1) ||(S1_SATF2>1)) &&( (S1_SATF3<1) ||(S1_SATF3>1)) &&( (S1_SATF0<1) ||(S1_SATF0>1)) &&( (S1_SATF1<1) ||(S1_SATF1>1)) &&((T_DY_NT<0)||(T_DY_NT>64)) &&((T_SAA <0)||(T_SAA >64))-> Standard Output From FTOOL xselect:
** XSELECT V1.3 **
!> Enter session name >[xsel] screen
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS S1CCDPOW
1 GAL_RIDG BRIGHT2 HIGH 09/04/97 21:02:58 0.17E+05 202435 1111
Processing file: /data/data16/seq_proc/55000030.005/ad55000030s100112h.unf
EXTRACTOR vers 2.0 11 Apr 1997.
Doing file: /data/data16/seq_proc/55000030.005/screen_work1001.xsl
Total Good Bad: Region Time Phase Cut
111705 65437 0 46268 0 0
Writing events file
65437 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
111705 65437 0 46268 0 0
in 7007.70 seconds
CLEANSIS_V1.6
allocating image arrays...
PROGRAM TO MAKE AN SIS SCIENCE FILE CLEANED OF ANOMALOUS PIXELS.
* Anomalous pixels may consist of at least two populations.
1. Persistent HOT pixels are removed by comparing to the chip mean.
2. Flickering WARM pixels are removed by comparing to the cell mean.
3. In faint areas (zero bgd), flickering pixels are removed with a
cutoff threshold.
Hints:
Choose cell size and thresholds based on the expected background and the PSF.
Use the DIRTYSIS option to examine the anomalous pixel spectra.
Try a multiple pass clean:
Choose a PHA cut to optimize the S/N of the flickering pixels,
then a broad band clean.
Be suspicious of extended source cleans.
For very bright sources you may need to turn off the iteration option.
See the help page for further info (fhelp cleansis)
Poisson clean cell size : 5
Poisson probability threshold : 0.631E-05
Zero Bgd Cutoff threshold (>) : 3
Iterate : T
Dirtysis : F
Minimum PHA value (inclusive) : 0
Maximum PHA value (inclusive) : 4095
open output file: /data/data16/seq_proc/55000030.005/screen_in_event.xsl
reading data file: /data/data16/seq_proc/55000030.005/screen_out_event.xsl
copying primary header to output file...
making chip image...
Total counts in chip images : 65437
copy bad pix array...
cleaning chip # 0
Hot pixels & counts : 65 17435
Flickering pixels iter, pixels & cnts : 1 39 676
cleaning chip # 1
Hot pixels & counts : 65 18685
Flickering pixels iter, pixels & cnts : 1 38 758
cleaning chip # 2
Hot pixels & counts : 58 14416
Flickering pixels iter, pixels & cnts : 1 40 905
cleaning chip # 3
Hot pixels & counts : 61 10867
Flickering pixels iter, pixels & cnts : 1 16 300
Number of pixels rejected : 382
Number of (internal) image counts : 65437
Number of image cts rejected (N, %) : 64042 97.8681793
By chip : 0 1 2 3
Pixels rejected : 104 103 98 77
Image counts : 18359 19908 15779 11391
Image cts rejected: 18111 19443 15321 11167
Image cts rej (%) : 98.65 97.66 97.10 98.03
filtering data...
Total counts : 18359 19908 15779 11391
Total cts rejected: 18111 19443 15321 11167
Total cts rej (%) : 98.65 97.66 97.10 98.03
Number of clean counts accepted : 1395
writing history cards...
copying extensions...
writing out hot pixs...
Number of rejected pixels : 382
updating NEVENTS keywords...
closing data file...
closing clean file...
Command not found; type ? for a command listing
!screen:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!screen:ASCA > set datadir .
Setting data directory to /data/data16/seq_proc/55000030.005/
Setting mkf directory to /data/data16/seq_proc/55000030.005/
!screen:ASCA > read events ad55000030s100112h.unf
Got new instrument: SIS1
Setting: IMAGE binning = 4
WMAP binning = 8
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 4095
Got the minimum time resolution of the read data: 16.000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data16/seq_proc/55000030.005/
HK Directory is: /data/data16/seq_proc/55000030.005/
!screen:ASCA-SIS1-BRIGHT2 > select event "grade==0||grade==2||grade==3||grade==4" save_file=no
!screen:ASCA-SIS1-BRIGHT2 > select mkf "@criteria.tmp" data_dir=. ASCA_mkf_def_expr=ft*.mkf
!screen:ASCA-SIS1-BRIGHT2 > extract events
!screen:ASCA-SIS1-BRIGHT2 > sisclean saoimage=no sis_plot=no clean=2 cellsize=5 log_prob=-5.24 bkg_thr=3 clean_phalow=0 clean_phahi=4095
!screen:ASCA-SIS1-BRIGHT2 > save clean outfile=ad55000030s100112h.evt use_events=no
Wrote cleaned events file to ad55000030s100112h.evt
!screen:ASCA-SIS1-BRIGHT2 > exit save_session=no
-> Skipping ad55000030s100201h.unf because of mode(SAA==0) &&(BR_EARTH>20) &&(ELV>10) &&(COR>6) &&(ACS==0) &&(ANG_DIST>0)&& (ANG_DIST<0.01) &&(FOV==0) && ( (S1_PIXL0>0)&& (S1_PIXL1>0)&& (S1_PIXL2>0)&& (S1_PIXL3>0) ) &&( (S1_SATF2<1) ||(S1_SATF2>1)) &&( (S1_SATF3<1) ||(S1_SATF3>1)) &&( (S1_SATF0<1) ||(S1_SATF0>1)) &&( (S1_SATF1<1) ||(S1_SATF1>1)) &&((T_DY_NT<0)||(T_DY_NT>64)) &&((T_SAA <0)||(T_SAA >64))-> Standard Output From FTOOL xselect:
** XSELECT V1.3 **
!> Enter session name >[xsel] screen
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS S1CCDPOW
1 GAL_RIDG BRIGHT HIGH 10/04/97 02:43:42 0.19E+04 5902 1111
Processing file: /data/data16/seq_proc/55000030.005/ad55000030s100202h.unf
EXTRACTOR vers 2.0 11 Apr 1997.
Doing file: /data/data16/seq_proc/55000030.005/screen_work1001.xsl
Total Good Bad: Region Time Phase Cut
2032 44 0 1988 0 0
Writing events file
44 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
2032 44 0 1988 0 0
in 16.06 seconds
CLEANSIS_V1.6
allocating image arrays...
PROGRAM TO MAKE AN SIS SCIENCE FILE CLEANED OF ANOMALOUS PIXELS.
* Anomalous pixels may consist of at least two populations.
1. Persistent HOT pixels are removed by comparing to the chip mean.
2. Flickering WARM pixels are removed by comparing to the cell mean.
3. In faint areas (zero bgd), flickering pixels are removed with a
cutoff threshold.
Hints:
Choose cell size and thresholds based on the expected background and the PSF.
Use the DIRTYSIS option to examine the anomalous pixel spectra.
Try a multiple pass clean:
Choose a PHA cut to optimize the S/N of the flickering pixels,
then a broad band clean.
Be suspicious of extended source cleans.
For very bright sources you may need to turn off the iteration option.
See the help page for further info (fhelp cleansis)
Poisson clean cell size : 5
Poisson probability threshold : 0.631E-05
Zero Bgd Cutoff threshold (>) : 3
Iterate : T
Dirtysis : F
Minimum PHA value (inclusive) : 0
Maximum PHA value (inclusive) : 4095
open output file: /data/data16/seq_proc/55000030.005/screen_in_event.xsl
reading data file: /data/data16/seq_proc/55000030.005/screen_out_event.xsl
copying primary header to output file...
making chip image...
Total counts in chip images : 44
copy bad pix array...
cleaning chip # 0
Hot pixels & counts : 0 0
cleaning chip # 1
cleaning chip # 2
Hot pixels & counts : 0 0
cleaning chip # 3
Hot pixels & counts : 0 0
Number of pixels rejected : 0
Number of (internal) image counts : 44
Number of image cts rejected (N, %) : 0 0.0000000
By chip : 0 1 2 3
Pixels rejected : 0 0 0 0
Image counts : 21 0 16 7
Image cts rejected: 0 0 0 0
Image cts rej (%) : 0.00 0.00 0.00 0.00
filtering data...
Total counts : 21 0 16 7
Total cts rejected: 0 0 0 0
Total cts rej (%) : 0.00 0.00 0.00 0.00
Number of clean counts accepted : 44
writing history cards...
copying extensions...
writing out hot pixs...
Number of rejected pixels : 0
updating NEVENTS keywords...
closing data file...
closing clean file...
Command not found; type ? for a command listing
!screen:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!screen:ASCA > set datadir .
Setting data directory to /data/data16/seq_proc/55000030.005/
Setting mkf directory to /data/data16/seq_proc/55000030.005/
!screen:ASCA > read events ad55000030s100202h.unf
Got new instrument: SIS1
Setting: IMAGE binning = 4
WMAP binning = 8
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 2047
Got the minimum time resolution of the read data: 16.000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data16/seq_proc/55000030.005/
HK Directory is: /data/data16/seq_proc/55000030.005/
!screen:ASCA-SIS1-BRIGHT > select event "grade==0||grade==2||grade==3||grade==4" save_file=no
!screen:ASCA-SIS1-BRIGHT > select mkf "@criteria.tmp" data_dir=. ASCA_mkf_def_expr=ft*.mkf
!screen:ASCA-SIS1-BRIGHT > extract events
!screen:ASCA-SIS1-BRIGHT > sisclean saoimage=no sis_plot=no clean=2 cellsize=5 log_prob=-5.24 bkg_thr=3 clean_phalow=0 clean_phahi=4095
!screen:ASCA-SIS1-BRIGHT > save clean outfile=ad55000030s100202h.evt use_events=no
Wrote cleaned events file to ad55000030s100202h.evt
!screen:ASCA-SIS1-BRIGHT > exit save_session=no
-> Filtering ad55000030s100212h.unf into ad55000030s100212h.evt(SAA==0) &&(BR_EARTH>20) &&(ELV>10) &&(COR>6) &&(ACS==0) &&(ANG_DIST>0)&& (ANG_DIST<0.01) &&(FOV==0) && ( (S1_PIXL0>0)&& (S1_PIXL1>0)&& (S1_PIXL2>0)&& (S1_PIXL3>0) ) &&( (S1_SATF2<1) ||(S1_SATF2>1)) &&( (S1_SATF3<1) ||(S1_SATF3>1)) &&( (S1_SATF0<1) ||(S1_SATF0>1)) &&( (S1_SATF1<1) ||(S1_SATF1>1)) &&((T_DY_NT<0)||(T_DY_NT>64)) &&((T_SAA <0)||(T_SAA >64))-> Standard Output From FTOOL xselect:
** XSELECT V1.3 **
!> Enter session name >[xsel] screen
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS S1CCDPOW
1 GAL_RIDG BRIGHT2 HIGH 10/04/97 02:43:42 0.19E+04 8860 1111
Processing file: /data/data16/seq_proc/55000030.005/ad55000030s100212h.unf
EXTRACTOR vers 2.0 11 Apr 1997.
Doing file: /data/data16/seq_proc/55000030.005/screen_work1001.xsl
Total Good Bad: Region Time Phase Cut
4403 109 0 4294 0 0
Writing events file
109 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
4403 109 0 4294 0 0
in 16.06 seconds
CLEANSIS_V1.6
allocating image arrays...
PROGRAM TO MAKE AN SIS SCIENCE FILE CLEANED OF ANOMALOUS PIXELS.
* Anomalous pixels may consist of at least two populations.
1. Persistent HOT pixels are removed by comparing to the chip mean.
2. Flickering WARM pixels are removed by comparing to the cell mean.
3. In faint areas (zero bgd), flickering pixels are removed with a
cutoff threshold.
Hints:
Choose cell size and thresholds based on the expected background and the PSF.
Use the DIRTYSIS option to examine the anomalous pixel spectra.
Try a multiple pass clean:
Choose a PHA cut to optimize the S/N of the flickering pixels,
then a broad band clean.
Be suspicious of extended source cleans.
For very bright sources you may need to turn off the iteration option.
See the help page for further info (fhelp cleansis)
Poisson clean cell size : 5
Poisson probability threshold : 0.631E-05
Zero Bgd Cutoff threshold (>) : 3
Iterate : T
Dirtysis : F
Minimum PHA value (inclusive) : 0
Maximum PHA value (inclusive) : 4095
open output file: /data/data16/seq_proc/55000030.005/screen_in_event.xsl
reading data file: /data/data16/seq_proc/55000030.005/screen_out_event.xsl
copying primary header to output file...
making chip image...
Total counts in chip images : 109
copy bad pix array...
cleaning chip # 0
Hot pixels & counts : 0 0
cleaning chip # 1
cleaning chip # 2
Hot pixels & counts : 0 0
cleaning chip # 3
Hot pixels & counts : 0 0
Number of pixels rejected : 0
Number of (internal) image counts : 109
Number of image cts rejected (N, %) : 0 0.0000000
By chip : 0 1 2 3
Pixels rejected : 0 0 0 0
Image counts : 44 0 35 30
Image cts rejected: 0 0 0 0
Image cts rej (%) : 0.00 0.00 0.00 0.00
filtering data...
Total counts : 44 0 35 30
Total cts rejected: 0 0 0 0
Total cts rej (%) : 0.00 0.00 0.00 0.00
Number of clean counts accepted : 109
writing history cards...
copying extensions...
writing out hot pixs...
Number of rejected pixels : 0
updating NEVENTS keywords...
closing data file...
closing clean file...
Command not found; type ? for a command listing
!screen:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!screen:ASCA > set datadir .
Setting data directory to /data/data16/seq_proc/55000030.005/
Setting mkf directory to /data/data16/seq_proc/55000030.005/
!screen:ASCA > read events ad55000030s100212h.unf
Got new instrument: SIS1
Setting: IMAGE binning = 4
WMAP binning = 8
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 4095
Got the minimum time resolution of the read data: 16.000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data16/seq_proc/55000030.005/
HK Directory is: /data/data16/seq_proc/55000030.005/
!screen:ASCA-SIS1-BRIGHT2 > select event "grade==0||grade==2||grade==3||grade==4" save_file=no
!screen:ASCA-SIS1-BRIGHT2 > select mkf "@criteria.tmp" data_dir=. ASCA_mkf_def_expr=ft*.mkf
!screen:ASCA-SIS1-BRIGHT2 > extract events
!screen:ASCA-SIS1-BRIGHT2 > sisclean saoimage=no sis_plot=no clean=2 cellsize=5 log_prob=-5.24 bkg_thr=3 clean_phalow=0 clean_phahi=4095
!screen:ASCA-SIS1-BRIGHT2 > save clean outfile=ad55000030s100212h.evt use_events=no
Wrote cleaned events file to ad55000030s100212h.evt
!screen:ASCA-SIS1-BRIGHT2 > exit save_session=no
-> Filtering ad55000030s100302m.unf into ad55000030s100302m.evt(SAA==0) &&(BR_EARTH>20) &&(ELV>10) &&(COR>6) &&(ACS==0) &&(ANG_DIST>0)&& (ANG_DIST<0.01) &&(FOV==0) && ( (S1_PIXL0>0)&& (S1_PIXL1>0)&& (S1_PIXL2>0)&& (S1_PIXL3>0) ) &&( (S1_SATF2<1) ||(S1_SATF2>1)) &&( (S1_SATF3<1) ||(S1_SATF3>1)) &&( (S1_SATF0<1) ||(S1_SATF0>1)) &&( (S1_SATF1<1) ||(S1_SATF1>1)) &&((T_DY_NT<0)||(T_DY_NT>64)) &&((T_SAA <0)||(T_SAA >64))-> Standard Output From FTOOL xselect:
** XSELECT V1.3 **
!> Enter session name >[xsel] screen
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS S1CCDPOW
1 GAL_RIDG BRIGHT MEDIUM 09/04/97 20:51:26 0.24E+04 18867 1111
Processing file: /data/data16/seq_proc/55000030.005/ad55000030s100302m.unf
EXTRACTOR vers 2.0 11 Apr 1997.
Doing file: /data/data16/seq_proc/55000030.005/screen_work1001.xsl
Total Good Bad: Region Time Phase Cut
4598 159 0 4439 0 0
Writing events file
159 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
4598 159 0 4439 0 0
in 80.00 seconds
CLEANSIS_V1.6
allocating image arrays...
PROGRAM TO MAKE AN SIS SCIENCE FILE CLEANED OF ANOMALOUS PIXELS.
* Anomalous pixels may consist of at least two populations.
1. Persistent HOT pixels are removed by comparing to the chip mean.
2. Flickering WARM pixels are removed by comparing to the cell mean.
3. In faint areas (zero bgd), flickering pixels are removed with a
cutoff threshold.
Hints:
Choose cell size and thresholds based on the expected background and the PSF.
Use the DIRTYSIS option to examine the anomalous pixel spectra.
Try a multiple pass clean:
Choose a PHA cut to optimize the S/N of the flickering pixels,
then a broad band clean.
Be suspicious of extended source cleans.
For very bright sources you may need to turn off the iteration option.
See the help page for further info (fhelp cleansis)
Poisson clean cell size : 5
Poisson probability threshold : 0.631E-05
Zero Bgd Cutoff threshold (>) : 3
Iterate : T
Dirtysis : F
Minimum PHA value (inclusive) : 0
Maximum PHA value (inclusive) : 4095
open output file: /data/data16/seq_proc/55000030.005/screen_in_event.xsl
reading data file: /data/data16/seq_proc/55000030.005/screen_out_event.xsl
copying primary header to output file...
making chip image...
Total counts in chip images : 159
copy bad pix array...
cleaning chip # 0
Hot pixels & counts : 6 25
Flickering pixels iter, pixels & cnts : 1 3 9
cleaning chip # 1
Hot pixels & counts : 5 19
cleaning chip # 2
Hot pixels & counts : 7 25
cleaning chip # 3
Hot pixels & counts : 5 24
Number of pixels rejected : 26
Number of (internal) image counts : 159
Number of image cts rejected (N, %) : 102 64.1509399
By chip : 0 1 2 3
Pixels rejected : 9 5 7 5
Image counts : 46 32 43 38
Image cts rejected: 34 19 25 24
Image cts rej (%) : 73.91 59.38 58.14 63.16
filtering data...
Total counts : 46 32 43 38
Total cts rejected: 34 19 25 24
Total cts rej (%) : 73.91 59.38 58.14 63.16
Number of clean counts accepted : 57
writing history cards...
copying extensions...
writing out hot pixs...
Number of rejected pixels : 26
updating NEVENTS keywords...
closing data file...
closing clean file...
Command not found; type ? for a command listing
!screen:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!screen:ASCA > set datadir .
Setting data directory to /data/data16/seq_proc/55000030.005/
Setting mkf directory to /data/data16/seq_proc/55000030.005/
!screen:ASCA > read events ad55000030s100302m.unf
Got new instrument: SIS1
Setting: IMAGE binning = 4
WMAP binning = 8
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 2047
Got the minimum time resolution of the read data: 16.000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data16/seq_proc/55000030.005/
HK Directory is: /data/data16/seq_proc/55000030.005/
!screen:ASCA-SIS1-BRIGHT > select event "grade==0||grade==2||grade==3||grade==4" save_file=no
!screen:ASCA-SIS1-BRIGHT > select mkf "@criteria.tmp" data_dir=. ASCA_mkf_def_expr=ft*.mkf
!screen:ASCA-SIS1-BRIGHT > extract events
!screen:ASCA-SIS1-BRIGHT > sisclean saoimage=no sis_plot=no clean=2 cellsize=5 log_prob=-5.24 bkg_thr=3 clean_phalow=0 clean_phahi=4095
!screen:ASCA-SIS1-BRIGHT > save clean outfile=ad55000030s100302m.evt use_events=no
Wrote cleaned events file to ad55000030s100302m.evt
!screen:ASCA-SIS1-BRIGHT > exit save_session=no
-> Filtering ad55000030g200170h.unf into ad55000030g200170h.evt(SAA==0)&& (COR>4)&& (G2_H0+G2_H2+G3_H0+G3_H2<45)&& (G2_H0+G2_H2+G3_H0+G3_H2<0.45*COR**2-13*COR+125)&& (RBM_CONT<100)&& (ELV>5)&& (ACS==0)&& (ANG_DIST>0)&& (ANG_DIST<0.01)&& (G2_L1>0)-> Standard Output From FTOOL xselect:
** XSELECT V1.3 **
!> Enter session name >[xsel] screen
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS PHA_BINS
1 GAL_RIDG PH HIGH 09/04/97 21:03:10 0.19E+05 19577 1024
EXTRACTOR vers 2.0 11 Apr 1997.
Doing file: /data/data16/seq_proc/55000030.005/ad55000030g200170h.unf
Total Good Bad: Region Time Phase Cut
19577 5743 9834 4000 0 0
Writing events file
5743 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
19577 5743 9834 4000 0 0
in 7796.22 seconds
Infile # of rows Outfile # of rows # filtered
---------------- ----------------- ----------
5743 5406 337
Command not found; type ? for a command listing
!screen:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!screen:ASCA > set datadir .
Setting data directory to /data/data16/seq_proc/55000030.005/
Setting mkf directory to /data/data16/seq_proc/55000030.005/
!screen:ASCA > read events ad55000030g200170h.unf
Got new instrument: GIS2
Setting: IMAGE binning = 1
WMAP binning = 1
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 1023
Got the minimum time resolution of the read data: 0.62500E-01
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data16/seq_proc/55000030.005/
HK Directory is: /data/data16/seq_proc/55000030.005/
!screen:ASCA-GIS2-PH > filter region GIS2_REGION256.4
!screen:ASCA-GIS2-PH > select mkf "@criteria.tmp" data_dir=. ASCA_mkf_def_expr=ft*.mkf
!screen:ASCA-GIS2-PH > extract events
!screen:ASCA-GIS2-PH > gisclean
Using table:/opt/local/ftools/ftools.4.0.c/SunOS_5.4_sparc/refdata/rti_gis_1024_040693.fits
!screen:ASCA-GIS2-PH > save clean outfile=ad55000030g200170h.evt use_events=no
!screen:ASCA-GIS2-PH > exit save_session=no
-> Setting NEVENTS to 5406 in ad55000030g200170h.unf(SAA==0)&& (COR>4)&& (G2_H0+G2_H2+G3_H0+G3_H2<45)&& (G2_H0+G2_H2+G3_H0+G3_H2<0.45*COR**2-13*COR+125)&& (RBM_CONT<100)&& (ELV>5)&& (ACS==0)&& (ANG_DIST>0)&& (ANG_DIST<0.01)&& (G3_L1>0)-> Standard Output From FTOOL xselect:
** XSELECT V1.3 **
!> Enter session name >[xsel] screen
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS PHA_BINS
1 GAL_RIDG PH HIGH 09/04/97 21:03:10 0.19E+05 18594 1024
EXTRACTOR vers 2.0 11 Apr 1997.
Doing file: /data/data16/seq_proc/55000030.005/ad55000030g300170h.unf
Total Good Bad: Region Time Phase Cut
18594 5917 8266 4411 0 0
Writing events file
5917 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
18594 5917 8266 4411 0 0
in 7788.22 seconds
Infile # of rows Outfile # of rows # filtered
---------------- ----------------- ----------
5917 5519 398
Command not found; type ? for a command listing
!screen:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!screen:ASCA > set datadir .
Setting data directory to /data/data16/seq_proc/55000030.005/
Setting mkf directory to /data/data16/seq_proc/55000030.005/
!screen:ASCA > read events ad55000030g300170h.unf
Got new instrument: GIS3
Setting: IMAGE binning = 1
WMAP binning = 1
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 1023
Got the minimum time resolution of the read data: 0.62500E-01
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data16/seq_proc/55000030.005/
HK Directory is: /data/data16/seq_proc/55000030.005/
!screen:ASCA-GIS3-PH > filter region GIS3_REGION256.4
!screen:ASCA-GIS3-PH > select mkf "@criteria.tmp" data_dir=. ASCA_mkf_def_expr=ft*.mkf
!screen:ASCA-GIS3-PH > extract events
!screen:ASCA-GIS3-PH > gisclean
Using table:/opt/local/ftools/ftools.4.0.c/SunOS_5.4_sparc/refdata/rti_gis_1024_040693.fits
!screen:ASCA-GIS3-PH > save clean outfile=ad55000030g300170h.evt use_events=no
!screen:ASCA-GIS3-PH > exit save_session=no
-> Setting NEVENTS to 5519 in ad55000030g300170h.unf-ANNULUS(128.5,128.5,192,88) -ELLIPSE(167.5,220,24.66,28.95,245.298)-> gis2_ano_on_flf_180295.fits already present in current directory
ASCAEXPO_V0.9b
reading data file: ad55000030g200170h.evt
reading gti ext: STDGTI
reading cal file: gis2_ano_on_flf_180295.fits
reading inst file: GIS2_REGION256.4_regionmap.tmp
making an inst map...
multiply inst map...
reading att file: ./fa970409_2051.0625
making an exposure map...
Aspect RA/DEC/ROLL : 275.6770 -13.7019 284.7642
Mean RA/DEC/ROLL : 275.6767 -13.7261 284.7642
Pnt RA/DEC/ROLL : 275.6743 -13.6773 284.7642
Image rebin factor : 1
Attitude Records : 46381
GTI intervals : 29
Total GTI (secs) : 7796.220
Max attitude excursion (arcsecs) : 5.000
0 Percent Complete: Total/live time: 0.0000000 0.0000000
10 Percent Complete: Total/live time: 2424.0305176 2424.0305176
20 Percent Complete: Total/live time: 2424.0305176 2424.0305176
30 Percent Complete: Total/live time: 2561.0297852 2561.0297852
40 Percent Complete: Total/live time: 4182.0727539 4182.0727539
50 Percent Complete: Total/live time: 4182.0727539 4182.0727539
60 Percent Complete: Total/live time: 5364.1337891 5364.1337891
70 Percent Complete: Total/live time: 6644.1225586 6644.1225586
80 Percent Complete: Total/live time: 6644.1225586 6644.1225586
90 Percent Complete: Total/live time: 7796.2197266 7796.2197266
100 Percent Complete: Total/live time: 7796.2197266 7796.2197266
Number of attitude steps used: 14
Number of attitude steps avail: 32132
Mean RA/DEC pixel offset: -10.6949 -2.9074
writing expo file: ad55000030g200170h.expo
closing attitude file...
closing data file...
-> Generating low and high energy images for ad55000030g200170h.evt
** XSELECT V1.3 **
!> Enter session name >[xsel] ad55000030g200170h
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS PHA_BINS
1 GAL_RIDG PH HIGH 09/04/97 21:03:10 0.78E+04 5406 1024
EXTRACTOR vers 2.0 11 Apr 1997.
Getting FITS WCS Keywords
Doing file: /data/data16/seq_proc/55000030.005/ad55000030g200170h.evt
Total Good Bad: Region Time Phase Cut
5406 5339 67 0 0 0
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
5406 5339 67 0 0 0
in 7796.22 seconds
Image has 5339 counts for 0.6848 counts/sec
EXTRACTOR vers 2.0 11 Apr 1997.
Getting FITS WCS Keywords
Doing file: /data/data16/seq_proc/55000030.005/ad55000030g200170h.evt
Total Good Bad: Region Time Phase Cut
5406 2252 67 0 0 3087
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
5406 2252 67 0 0 3087
in 7796.22 seconds
Image has 2252 counts for 0.2889 counts/sec
EXTRACTOR vers 2.0 11 Apr 1997.
Getting FITS WCS Keywords
Doing file: /data/data16/seq_proc/55000030.005/ad55000030g200170h.evt
Total Good Bad: Region Time Phase Cut
5406 3111 67 0 0 2228
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
5406 3111 67 0 0 2228
in 7796.22 seconds
Image has 3111 counts for 0.3990 counts/sec
Command not found; type ? for a command listing
!ad55000030g200170h:ASCA >
!ad55000030g200170h:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!ad55000030g200170h:ASCA > set datadir .
Setting data directory to /data/data16/seq_proc/55000030.005/
Setting mkf directory to /data/data16/seq_proc/55000030.005/
!ad55000030g200170h:ASCA > read events ad55000030g200170h.evt
Got new instrument: GIS2
Setting: IMAGE binning = 1
WMAP binning = 1
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 1023
Got the minimum time resolution of the read data: 0.62500E-01
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data16/seq_proc/55000030.005/
HK Directory is: /data/data16/seq_proc/55000030.005/
!ad55000030g200170h:ASCA-GIS2-PH > set image sky
!ad55000030g200170h:ASCA-GIS2-PH > filter region corner_point.reg
!ad55000030g200170h:ASCA-GIS2-PH > extract image
!ad55000030g200170h:ASCA-GIS2-PH > save image outfile=ad55000030g200170h.img
Wrote image to file ad55000030g200170h.img
!ad55000030g200170h:ASCA-GIS2-PH > filter pha_cut 0 170
!ad55000030g200170h:ASCA-GIS2-PH > extract image
!ad55000030g200170h:ASCA-GIS2-PH > save image outfile=ad55000030g200170h_lo.img
Wrote image to file ad55000030g200170h_lo.img
!ad55000030g200170h:ASCA-GIS2-PH > clear pha_cut
!ad55000030g200170h:ASCA-GIS2-PH > filter pha_cut 170 1024
Warning: your PI upper bound: 1024 is above the maximum value.
!ad55000030g200170h:ASCA-GIS2-PH > extract image
!ad55000030g200170h:ASCA-GIS2-PH > save image outfile=ad55000030g200170h_hi.img
Wrote image to file ad55000030g200170h_hi.img
!ad55000030g200170h:ASCA-GIS2-PH > exit save_session=no
-> Generating exposure map ad55000030g300170h.expo-ANNULUS(128.5,128.5,192,88) -ELLIPSE(217,95,21.56,25.92,169.216)-> gis3_ano_on_flf_180295.fits already present in current directory
ASCAEXPO_V0.9b
reading data file: ad55000030g300170h.evt
reading gti ext: STDGTI
reading cal file: gis3_ano_on_flf_180295.fits
reading inst file: GIS3_REGION256.4_regionmap.tmp
making an inst map...
multiply inst map...
reading att file: ./fa970409_2051.0625
making an exposure map...
Aspect RA/DEC/ROLL : 275.6770 -13.7019 284.7652
Mean RA/DEC/ROLL : 275.6727 -13.7016 284.7652
Pnt RA/DEC/ROLL : 275.6784 -13.7018 284.7652
Image rebin factor : 1
Attitude Records : 46381
GTI intervals : 28
Total GTI (secs) : 7788.220
Max attitude excursion (arcsecs) : 5.000
0 Percent Complete: Total/live time: 0.0000000 0.0000000
10 Percent Complete: Total/live time: 2420.0305176 2420.0305176
20 Percent Complete: Total/live time: 2420.0305176 2420.0305176
30 Percent Complete: Total/live time: 2555.0297852 2555.0297852
40 Percent Complete: Total/live time: 4176.0727539 4176.0727539
50 Percent Complete: Total/live time: 4176.0727539 4176.0727539
60 Percent Complete: Total/live time: 5356.1337891 5356.1337891
70 Percent Complete: Total/live time: 6636.1225586 6636.1225586
80 Percent Complete: Total/live time: 6636.1225586 6636.1225586
90 Percent Complete: Total/live time: 7788.2197266 7788.2197266
100 Percent Complete: Total/live time: 7788.2197266 7788.2197266
Number of attitude steps used: 14
Number of attitude steps avail: 32131
Mean RA/DEC pixel offset: 0.5189 -1.7983
writing expo file: ad55000030g300170h.expo
closing attitude file...
closing data file...
-> Generating low and high energy images for ad55000030g300170h.evt
** XSELECT V1.3 **
!> Enter session name >[xsel] ad55000030g300170h
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS PHA_BINS
1 GAL_RIDG PH HIGH 09/04/97 21:03:10 0.78E+04 5519 1024
EXTRACTOR vers 2.0 11 Apr 1997.
Getting FITS WCS Keywords
Doing file: /data/data16/seq_proc/55000030.005/ad55000030g300170h.evt
Total Good Bad: Region Time Phase Cut
5519 5454 65 0 0 0
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
5519 5454 65 0 0 0
in 7788.22 seconds
Image has 5454 counts for 0.7003 counts/sec
EXTRACTOR vers 2.0 11 Apr 1997.
Getting FITS WCS Keywords
Doing file: /data/data16/seq_proc/55000030.005/ad55000030g300170h.evt
Total Good Bad: Region Time Phase Cut
5519 2284 65 0 0 3170
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
5519 2284 65 0 0 3170
in 7788.22 seconds
Image has 2284 counts for 0.2933 counts/sec
EXTRACTOR vers 2.0 11 Apr 1997.
Getting FITS WCS Keywords
Doing file: /data/data16/seq_proc/55000030.005/ad55000030g300170h.evt
Total Good Bad: Region Time Phase Cut
5519 3203 65 0 0 2251
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
5519 3203 65 0 0 2251
in 7788.22 seconds
Image has 3203 counts for 0.4113 counts/sec
Command not found; type ? for a command listing
!ad55000030g300170h:ASCA >
!ad55000030g300170h:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!ad55000030g300170h:ASCA > set datadir .
Setting data directory to /data/data16/seq_proc/55000030.005/
Setting mkf directory to /data/data16/seq_proc/55000030.005/
!ad55000030g300170h:ASCA > read events ad55000030g300170h.evt
Got new instrument: GIS3
Setting: IMAGE binning = 1
WMAP binning = 1
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 1023
Got the minimum time resolution of the read data: 0.62500E-01
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data16/seq_proc/55000030.005/
HK Directory is: /data/data16/seq_proc/55000030.005/
!ad55000030g300170h:ASCA-GIS3-PH > set image sky
!ad55000030g300170h:ASCA-GIS3-PH > filter region corner_point.reg
!ad55000030g300170h:ASCA-GIS3-PH > extract image
!ad55000030g300170h:ASCA-GIS3-PH > save image outfile=ad55000030g300170h.img
Wrote image to file ad55000030g300170h.img
!ad55000030g300170h:ASCA-GIS3-PH > filter pha_cut 0 170
!ad55000030g300170h:ASCA-GIS3-PH > extract image
!ad55000030g300170h:ASCA-GIS3-PH > save image outfile=ad55000030g300170h_lo.img
Wrote image to file ad55000030g300170h_lo.img
!ad55000030g300170h:ASCA-GIS3-PH > clear pha_cut
!ad55000030g300170h:ASCA-GIS3-PH > filter pha_cut 170 1024
Warning: your PI upper bound: 1024 is above the maximum value.
!ad55000030g300170h:ASCA-GIS3-PH > extract image
!ad55000030g300170h:ASCA-GIS3-PH > save image outfile=ad55000030g300170h_hi.img
Wrote image to file ad55000030g300170h_hi.img
!ad55000030g300170h:ASCA-GIS3-PH > exit save_session=no
-> Generating exposure map ad55000030s000102h.expo
ASCAEXPO_V0.9b
reading data file: ad55000030s000102h.evt
reading gti ext: STDGTI
reading hp ext: HOT_PIXELS
reading cal file: s0_teldef_ascalin.fits
making an inst map...
SIS AREA DISC ENABL ON
CHIP: 0 1 2 3
CCD POWER ON/OFF: ON ON ON ON
AREA DISC IN/OUT: OUT OUT IN IN
AREA DISC H START: 6 6 6 316
AREA DISC H STOP: 425 425 200 425
AREA DISC V START: 2 2 2 2
AREA DISC V STOP: 422 422 150 112
reading att file: ./fa970409_2051.0625
making an exposure map...
Aspect RA/DEC/ROLL : 275.6770 -13.7019 284.7681
Mean RA/DEC/ROLL : 275.6592 -13.7175 284.7681
Pnt RA/DEC/ROLL : 275.6955 -13.6867 284.7681
Image rebin factor : 4
Attitude Records : 46381
Hot Pixels : 95
GTI intervals : 7
Total GTI (secs) : 414.239
Max attitude excursion (arcsecs) : 5.000
0 Percent Complete: Total/live time: 0.0000000 0.0000000
10 Percent Complete: Total/live time: 56.0116539 56.0116539
20 Percent Complete: Total/live time: 111.0115204 111.0115204
30 Percent Complete: Total/live time: 144.0408936 144.0408936
40 Percent Complete: Total/live time: 200.0878296 200.0878296
50 Percent Complete: Total/live time: 254.0566101 254.0566101
60 Percent Complete: Total/live time: 254.0566101 254.0566101
70 Percent Complete: Total/live time: 334.1387939 334.1387939
80 Percent Complete: Total/live time: 414.2386475 414.2386475
100 Percent Complete: Total/live time: 414.2386475 414.2386475
Number of attitude steps used: 8
Number of attitude steps avail: 15629
Mean RA/DEC pixel offset: -42.9714 -82.4354
writing expo file: ad55000030s000102h.expo
closing attitude file...
closing data file...
-> Generating low and high energy images for ad55000030s000102h.evt
** XSELECT V1.3 **
!> Enter session name >[xsel] ad55000030s000102h
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS S0CCDPOW
1 GAL_RIDG BRIGHT HIGH 09/04/97 21:55:34 0.41E+03 137 1111
EXTRACTOR vers 2.0 11 Apr 1997.
Getting FITS WCS Keywords
Doing file: /data/data16/seq_proc/55000030.005/ad55000030s000102h.evt
Total Good Bad: Region Time Phase Cut
137 137 0 0 0 0
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
137 137 0 0 0 0
in 414.24 seconds
Image has 137 counts for 0.3307 counts/sec
EXTRACTOR vers 2.0 11 Apr 1997.
Getting FITS WCS Keywords
Doing file: /data/data16/seq_proc/55000030.005/ad55000030s000102h.evt
Total Good Bad: Region Time Phase Cut
137 107 0 0 0 30
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
137 107 0 0 0 30
in 414.24 seconds
Image has 107 counts for 0.2583 counts/sec
EXTRACTOR vers 2.0 11 Apr 1997.
Getting FITS WCS Keywords
Doing file: /data/data16/seq_proc/55000030.005/ad55000030s000102h.evt
Total Good Bad: Region Time Phase Cut
137 30 0 0 0 107
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
137 30 0 0 0 107
in 414.24 seconds
Image has 30 counts for 7.2422E-02 counts/sec
Command not found; type ? for a command listing
!ad55000030s000102h:ASCA >
!ad55000030s000102h:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!ad55000030s000102h:ASCA > set datadir .
Setting data directory to /data/data16/seq_proc/55000030.005/
Setting mkf directory to /data/data16/seq_proc/55000030.005/
!ad55000030s000102h:ASCA > read events ad55000030s000102h.evt
Got new instrument: SIS0
Setting: IMAGE binning = 4
WMAP binning = 8
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 2047
Got the minimum time resolution of the read data: 16.000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data16/seq_proc/55000030.005/
HK Directory is: /data/data16/seq_proc/55000030.005/
!ad55000030s000102h:ASCA-SIS0-BRIGHT > set image sky
!ad55000030s000102h:ASCA-SIS0-BRIGHT > filter region corner_point.reg
!ad55000030s000102h:ASCA-SIS0-BRIGHT > extract image
!ad55000030s000102h:ASCA-SIS0-BRIGHT > save image outfile=ad55000030s000102h.img
Wrote image to file ad55000030s000102h.img
!ad55000030s000102h:ASCA-SIS0-BRIGHT > filter pha_cut 0 547
!ad55000030s000102h:ASCA-SIS0-BRIGHT > extract image
!ad55000030s000102h:ASCA-SIS0-BRIGHT > save image outfile=ad55000030s000102h_lo.img
Wrote image to file ad55000030s000102h_lo.img
!ad55000030s000102h:ASCA-SIS0-BRIGHT > clear pha_cut
!ad55000030s000102h:ASCA-SIS0-BRIGHT > filter pha_cut 547 2048
Warning: your PI upper bound: 2048 is above the maximum value.
!ad55000030s000102h:ASCA-SIS0-BRIGHT > extract image
!ad55000030s000102h:ASCA-SIS0-BRIGHT > save image outfile=ad55000030s000102h_hi.img
Wrote image to file ad55000030s000102h_hi.img
!ad55000030s000102h:ASCA-SIS0-BRIGHT > exit save_session=no
-> Generating exposure map ad55000030s000202h.expo
ASCAEXPO_V0.9b
reading data file: ad55000030s000202h.evt
reading gti ext: STDGTI
reading hp ext: HOT_PIXELS
reading cal file: s0_teldef_ascalin.fits
making an inst map...
SIS AREA DISC ENABL OFF
CHIP: 0 1 2 3
CCD POWER ON/OFF: ON ON ON ON
AREA DISC IN/OUT: OUT OUT IN IN
AREA DISC H START: 6 6 6 316
AREA DISC H STOP: 425 425 200 425
AREA DISC V START: 2 2 2 2
AREA DISC V STOP: 422 422 150 112
reading att file: ./fa970409_2051.0625
making an exposure map...
Aspect RA/DEC/ROLL : 275.6770 -13.7019 284.7683
Mean RA/DEC/ROLL : 275.6596 -13.7178 284.7683
Pnt RA/DEC/ROLL : 275.6918 -13.6858 284.7683
Image rebin factor : 4
Attitude Records : 46381
Hot Pixels : 215
GTI intervals : 21
Total GTI (secs) : 6489.456
Max attitude excursion (arcsecs) : 5.000
0 Percent Complete: Total/live time: 0.0000000 0.0000000
10 Percent Complete: Total/live time: 1361.8439941 1361.8439941
20 Percent Complete: Total/live time: 1569.8721924 1569.8721924
30 Percent Complete: Total/live time: 2024.8284912 2024.8284912
40 Percent Complete: Total/live time: 3101.7001953 3101.7001953
50 Percent Complete: Total/live time: 4157.7001953 4157.7001953
60 Percent Complete: Total/live time: 4157.7001953 4157.7001953
70 Percent Complete: Total/live time: 5131.5869141 5131.5869141
80 Percent Complete: Total/live time: 5515.5869141 5515.5869141
90 Percent Complete: Total/live time: 6489.4560547 6489.4560547
100 Percent Complete: Total/live time: 6489.4560547 6489.4560547
Number of attitude steps used: 15
Number of attitude steps avail: 31101
Mean RA/DEC pixel offset: -46.9845 -86.2050
writing expo file: ad55000030s000202h.expo
closing attitude file...
closing data file...
-> Generating low and high energy images for ad55000030s000202h.evt
** XSELECT V1.3 **
!> Enter session name >[xsel] ad55000030s000202h
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS S0CCDPOW
1 GAL_RIDG BRIGHT HIGH 09/04/97 21:02:58 0.65E+04 1022 1111
EXTRACTOR vers 2.0 11 Apr 1997.
Getting FITS WCS Keywords
Doing file: /data/data16/seq_proc/55000030.005/ad55000030s000202h.evt
Total Good Bad: Region Time Phase Cut
1022 1022 0 0 0 0
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
1022 1022 0 0 0 0
in 6489.46 seconds
Image has 1022 counts for 0.1575 counts/sec
EXTRACTOR vers 2.0 11 Apr 1997.
Getting FITS WCS Keywords
Doing file: /data/data16/seq_proc/55000030.005/ad55000030s000202h.evt
Total Good Bad: Region Time Phase Cut
1022 362 0 0 0 660
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
1022 362 0 0 0 660
in 6489.46 seconds
Image has 362 counts for 5.5783E-02 counts/sec
EXTRACTOR vers 2.0 11 Apr 1997.
Getting FITS WCS Keywords
Doing file: /data/data16/seq_proc/55000030.005/ad55000030s000202h.evt
Total Good Bad: Region Time Phase Cut
1022 661 0 0 0 361
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
1022 661 0 0 0 361
in 6489.46 seconds
Image has 661 counts for 0.1019 counts/sec
Command not found; type ? for a command listing
!ad55000030s000202h:ASCA >
!ad55000030s000202h:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!ad55000030s000202h:ASCA > set datadir .
Setting data directory to /data/data16/seq_proc/55000030.005/
Setting mkf directory to /data/data16/seq_proc/55000030.005/
!ad55000030s000202h:ASCA > read events ad55000030s000202h.evt
Got new instrument: SIS0
Setting: IMAGE binning = 4
WMAP binning = 8
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 2047
Got the minimum time resolution of the read data: 16.000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data16/seq_proc/55000030.005/
HK Directory is: /data/data16/seq_proc/55000030.005/
!ad55000030s000202h:ASCA-SIS0-BRIGHT > set image sky
!ad55000030s000202h:ASCA-SIS0-BRIGHT > filter region corner_point.reg
!ad55000030s000202h:ASCA-SIS0-BRIGHT > extract image
!ad55000030s000202h:ASCA-SIS0-BRIGHT > save image outfile=ad55000030s000202h.img
Wrote image to file ad55000030s000202h.img
!ad55000030s000202h:ASCA-SIS0-BRIGHT > filter pha_cut 0 547
!ad55000030s000202h:ASCA-SIS0-BRIGHT > extract image
!ad55000030s000202h:ASCA-SIS0-BRIGHT > save image outfile=ad55000030s000202h_lo.img
Wrote image to file ad55000030s000202h_lo.img
!ad55000030s000202h:ASCA-SIS0-BRIGHT > clear pha_cut
!ad55000030s000202h:ASCA-SIS0-BRIGHT > filter pha_cut 547 2048
Warning: your PI upper bound: 2048 is above the maximum value.
!ad55000030s000202h:ASCA-SIS0-BRIGHT > extract image
!ad55000030s000202h:ASCA-SIS0-BRIGHT > save image outfile=ad55000030s000202h_hi.img
Wrote image to file ad55000030s000202h_hi.img
!ad55000030s000202h:ASCA-SIS0-BRIGHT > exit save_session=no
-> Generating exposure map ad55000030s000302m.expo
ASCAEXPO_V0.9b
reading data file: ad55000030s000302m.evt
reading gti ext: STDGTI
reading hp ext: HOT_PIXELS
reading cal file: s0_teldef_ascalin.fits
making an inst map...
SIS AREA DISC ENABL OFF
CHIP: 0 1 2 3
CCD POWER ON/OFF: ON ON ON ON
AREA DISC IN/OUT: OUT OUT IN IN
AREA DISC H START: 6 6 6 316
AREA DISC H STOP: 425 425 200 425
AREA DISC V START: 2 2 2 2
AREA DISC V STOP: 422 422 150 112
reading att file: ./fa970409_2051.0625
making an exposure map...
Aspect RA/DEC/ROLL : 275.6770 -13.7019 284.7682
Mean RA/DEC/ROLL : 275.6611 -13.7168 284.7682
Pnt RA/DEC/ROLL : 275.6860 -13.7153 284.7682
Image rebin factor : 4
Attitude Records : 46381
Hot Pixels : 48
GTI intervals : 1
Total GTI (secs) : 80.003
Max attitude excursion (arcsecs) : 5.000
0 Percent Complete: Total/live time: 0.0000000 0.0000000
10 Percent Complete: Total/live time: 80.0027237 80.0027237
100 Percent Complete: Total/live time: 80.0027237 80.0027237
Number of attitude steps used: 2
Number of attitude steps avail: 61
Mean RA/DEC pixel offset: -29.5076 -35.7846
writing expo file: ad55000030s000302m.expo
closing attitude file...
closing data file...
-> Generating low and high energy images for ad55000030s000302m.evt
** XSELECT V1.3 **
!> Enter session name >[xsel] ad55000030s000302m
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS S0CCDPOW
1 GAL_RIDG BRIGHT MEDIUM 09/04/97 20:51:26 0.80E+02 77 1111
EXTRACTOR vers 2.0 11 Apr 1997.
Getting FITS WCS Keywords
Doing file: /data/data16/seq_proc/55000030.005/ad55000030s000302m.evt
Total Good Bad: Region Time Phase Cut
77 77 0 0 0 0
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
77 77 0 0 0 0
in 80.00 seconds
Image has 77 counts for 0.9625 counts/sec
EXTRACTOR vers 2.0 11 Apr 1997.
Getting FITS WCS Keywords
Doing file: /data/data16/seq_proc/55000030.005/ad55000030s000302m.evt
Total Good Bad: Region Time Phase Cut
77 62 0 0 0 15
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
77 62 0 0 0 15
in 80.00 seconds
Image has 62 counts for 0.7750 counts/sec
EXTRACTOR vers 2.0 11 Apr 1997.
Getting FITS WCS Keywords
Doing file: /data/data16/seq_proc/55000030.005/ad55000030s000302m.evt
Total Good Bad: Region Time Phase Cut
77 15 0 0 0 62
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
77 15 0 0 0 62
in 80.00 seconds
Image has 15 counts for 0.1875 counts/sec
Command not found; type ? for a command listing
!ad55000030s000302m:ASCA >
!ad55000030s000302m:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!ad55000030s000302m:ASCA > set datadir .
Setting data directory to /data/data16/seq_proc/55000030.005/
Setting mkf directory to /data/data16/seq_proc/55000030.005/
!ad55000030s000302m:ASCA > read events ad55000030s000302m.evt
Got new instrument: SIS0
Setting: IMAGE binning = 4
WMAP binning = 8
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 2047
Got the minimum time resolution of the read data: 16.000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data16/seq_proc/55000030.005/
HK Directory is: /data/data16/seq_proc/55000030.005/
!ad55000030s000302m:ASCA-SIS0-BRIGHT > set image sky
!ad55000030s000302m:ASCA-SIS0-BRIGHT > filter region corner_point.reg
!ad55000030s000302m:ASCA-SIS0-BRIGHT > extract image
!ad55000030s000302m:ASCA-SIS0-BRIGHT > save image outfile=ad55000030s000302m.img
Wrote image to file ad55000030s000302m.img
!ad55000030s000302m:ASCA-SIS0-BRIGHT > filter pha_cut 0 547
!ad55000030s000302m:ASCA-SIS0-BRIGHT > extract image
!ad55000030s000302m:ASCA-SIS0-BRIGHT > save image outfile=ad55000030s000302m_lo.img
Wrote image to file ad55000030s000302m_lo.img
!ad55000030s000302m:ASCA-SIS0-BRIGHT > clear pha_cut
!ad55000030s000302m:ASCA-SIS0-BRIGHT > filter pha_cut 547 2048
Warning: your PI upper bound: 2048 is above the maximum value.
!ad55000030s000302m:ASCA-SIS0-BRIGHT > extract image
!ad55000030s000302m:ASCA-SIS0-BRIGHT > save image outfile=ad55000030s000302m_hi.img
Wrote image to file ad55000030s000302m_hi.img
!ad55000030s000302m:ASCA-SIS0-BRIGHT > exit save_session=no
-> Generating exposure map ad55000030s100102h.expo
ASCAEXPO_V0.9b
reading data file: ad55000030s100102h.evt
reading gti ext: STDGTI
reading hp ext: HOT_PIXELS
reading cal file: s1_teldef_ascalin.fits
making an inst map...
SIS AREA DISC ENABL OFF
CHIP: 0 1 2 3
CCD POWER ON/OFF: ON ON ON ON
AREA DISC IN/OUT: OUT OUT OUT OUT
AREA DISC H START: 6 6 6 6
AREA DISC H STOP: 425 425 425 103
AREA DISC V START: 2 2 2 2
AREA DISC V STOP: 422 422 422 422
reading att file: ./fa970409_2051.0625
making an exposure map...
Aspect RA/DEC/ROLL : 275.6770 -13.7019 284.7645
Mean RA/DEC/ROLL : 275.6756 -13.7147 284.7645
Pnt RA/DEC/ROLL : 275.6757 -13.6889 284.7645
Image rebin factor : 4
Attitude Records : 46381
Hot Pixels : 325
GTI intervals : 20
Total GTI (secs) : 7007.702
Max attitude excursion (arcsecs) : 5.000
0 Percent Complete: Total/live time: 0.0000000 0.0000000
10 Percent Complete: Total/live time: 1463.8638916 1463.8638916
20 Percent Complete: Total/live time: 1711.3632812 1711.3632812
30 Percent Complete: Total/live time: 3481.7983398 3481.7983398
40 Percent Complete: Total/live time: 3481.7983398 3481.7983398
50 Percent Complete: Total/live time: 4575.7021484 4575.7021484
60 Percent Complete: Total/live time: 4575.7021484 4575.7021484
70 Percent Complete: Total/live time: 5567.7021484 5567.7021484
80 Percent Complete: Total/live time: 5951.7021484 5951.7021484
90 Percent Complete: Total/live time: 7007.7021484 7007.7021484
100 Percent Complete: Total/live time: 7007.7021484 7007.7021484
Number of attitude steps used: 17
Number of attitude steps avail: 32684
Mean RA/DEC pixel offset: -51.1271 -19.3431
writing expo file: ad55000030s100102h.expo
closing attitude file...
closing data file...
-> Generating low and high energy images for ad55000030s100102h.evt
** XSELECT V1.3 **
!> Enter session name >[xsel] ad55000030s100102h
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS S1CCDPOW
1 GAL_RIDG BRIGHT HIGH 09/04/97 21:02:58 0.70E+04 740 1111
EXTRACTOR vers 2.0 11 Apr 1997.
Getting FITS WCS Keywords
Doing file: /data/data16/seq_proc/55000030.005/ad55000030s100102h.evt
Total Good Bad: Region Time Phase Cut
740 740 0 0 0 0
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
740 740 0 0 0 0
in 7007.70 seconds
Image has 740 counts for 0.1056 counts/sec
EXTRACTOR vers 2.0 11 Apr 1997.
Getting FITS WCS Keywords
Doing file: /data/data16/seq_proc/55000030.005/ad55000030s100102h.evt
Total Good Bad: Region Time Phase Cut
740 309 0 0 0 431
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
740 309 0 0 0 431
in 7007.70 seconds
Image has 309 counts for 4.4094E-02 counts/sec
EXTRACTOR vers 2.0 11 Apr 1997.
Getting FITS WCS Keywords
Doing file: /data/data16/seq_proc/55000030.005/ad55000030s100102h.evt
Total Good Bad: Region Time Phase Cut
740 431 0 0 0 309
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
740 431 0 0 0 309
in 7007.70 seconds
Image has 431 counts for 6.1504E-02 counts/sec
Command not found; type ? for a command listing
!ad55000030s100102h:ASCA >
!ad55000030s100102h:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!ad55000030s100102h:ASCA > set datadir .
Setting data directory to /data/data16/seq_proc/55000030.005/
Setting mkf directory to /data/data16/seq_proc/55000030.005/
!ad55000030s100102h:ASCA > read events ad55000030s100102h.evt
Got new instrument: SIS1
Setting: IMAGE binning = 4
WMAP binning = 8
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 2047
Got the minimum time resolution of the read data: 16.000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data16/seq_proc/55000030.005/
HK Directory is: /data/data16/seq_proc/55000030.005/
!ad55000030s100102h:ASCA-SIS1-BRIGHT > set image sky
!ad55000030s100102h:ASCA-SIS1-BRIGHT > filter region corner_point.reg
!ad55000030s100102h:ASCA-SIS1-BRIGHT > extract image
!ad55000030s100102h:ASCA-SIS1-BRIGHT > save image outfile=ad55000030s100102h.img
Wrote image to file ad55000030s100102h.img
!ad55000030s100102h:ASCA-SIS1-BRIGHT > filter pha_cut 0 547
!ad55000030s100102h:ASCA-SIS1-BRIGHT > extract image
!ad55000030s100102h:ASCA-SIS1-BRIGHT > save image outfile=ad55000030s100102h_lo.img
Wrote image to file ad55000030s100102h_lo.img
!ad55000030s100102h:ASCA-SIS1-BRIGHT > clear pha_cut
!ad55000030s100102h:ASCA-SIS1-BRIGHT > filter pha_cut 547 2048
Warning: your PI upper bound: 2048 is above the maximum value.
!ad55000030s100102h:ASCA-SIS1-BRIGHT > extract image
!ad55000030s100102h:ASCA-SIS1-BRIGHT > save image outfile=ad55000030s100102h_hi.img
Wrote image to file ad55000030s100102h_hi.img
!ad55000030s100102h:ASCA-SIS1-BRIGHT > exit save_session=no
-> Generating exposure map ad55000030s100202h.expo
ASCAEXPO_V0.9b
reading data file: ad55000030s100202h.evt
reading gti ext: STDGTI
reading hp ext: HOT_PIXELS
reading cal file: s1_teldef_ascalin.fits
making an inst map...
SIS AREA DISC ENABL OFF
CHIP: 0 1 2 3
CCD POWER ON/OFF: ON ON ON ON
AREA DISC IN/OUT: OUT OUT OUT OUT
AREA DISC H START: 6 6 6 6
AREA DISC H STOP: 425 425 425 103
AREA DISC V START: 2 2 2 2
AREA DISC V STOP: 422 422 422 422
reading att file: ./fa970409_2051.0625
making an exposure map...
Aspect RA/DEC/ROLL : 275.6770 -13.7019 284.7632
Mean RA/DEC/ROLL : 275.6755 -13.7144 284.7632
Pnt RA/DEC/ROLL : 275.6795 -13.6905 284.7632
Image rebin factor : 4
Attitude Records : 46381
Hot Pixels : 0
GTI intervals : 1
Total GTI (secs) : 16.065
Max attitude excursion (arcsecs) : 5.000
0 Percent Complete: Total/live time: 0.0000000 0.0000000
10 Percent Complete: Total/live time: 16.0647984 16.0647984
100 Percent Complete: Total/live time: 16.0647984 16.0647984
Number of attitude steps used: 2
Number of attitude steps avail: 196
Mean RA/DEC pixel offset: -26.2146 -9.3027
writing expo file: ad55000030s100202h.expo
closing attitude file...
closing data file...
-> Generating low and high energy images for ad55000030s100202h.evt
** XSELECT V1.3 **
!> Enter session name >[xsel] ad55000030s100202h
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS S1CCDPOW
1 GAL_RIDG BRIGHT HIGH 10/04/97 02:43:42 0.16E+02 44 1111
EXTRACTOR vers 2.0 11 Apr 1997.
Getting FITS WCS Keywords
Doing file: /data/data16/seq_proc/55000030.005/ad55000030s100202h.evt
Total Good Bad: Region Time Phase Cut
44 44 0 0 0 0
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
44 44 0 0 0 0
in 16.06 seconds
Image has 44 counts for 2.739 counts/sec
EXTRACTOR vers 2.0 11 Apr 1997.
Getting FITS WCS Keywords
Doing file: /data/data16/seq_proc/55000030.005/ad55000030s100202h.evt
Total Good Bad: Region Time Phase Cut
44 30 0 0 0 14
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
44 30 0 0 0 14
in 16.06 seconds
Image has 30 counts for 1.867 counts/sec
EXTRACTOR vers 2.0 11 Apr 1997.
Getting FITS WCS Keywords
Doing file: /data/data16/seq_proc/55000030.005/ad55000030s100202h.evt
Total Good Bad: Region Time Phase Cut
44 14 0 0 0 30
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
44 14 0 0 0 30
in 16.06 seconds
Image has 14 counts for 0.8715 counts/sec
Command not found; type ? for a command listing
!ad55000030s100202h:ASCA >
!ad55000030s100202h:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!ad55000030s100202h:ASCA > set datadir .
Setting data directory to /data/data16/seq_proc/55000030.005/
Setting mkf directory to /data/data16/seq_proc/55000030.005/
!ad55000030s100202h:ASCA > read events ad55000030s100202h.evt
Got new instrument: SIS1
Setting: IMAGE binning = 4
WMAP binning = 8
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 2047
Got the minimum time resolution of the read data: 16.000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data16/seq_proc/55000030.005/
HK Directory is: /data/data16/seq_proc/55000030.005/
!ad55000030s100202h:ASCA-SIS1-BRIGHT > set image sky
!ad55000030s100202h:ASCA-SIS1-BRIGHT > filter region corner_point.reg
!ad55000030s100202h:ASCA-SIS1-BRIGHT > extract image
!ad55000030s100202h:ASCA-SIS1-BRIGHT > save image outfile=ad55000030s100202h.img
Wrote image to file ad55000030s100202h.img
!ad55000030s100202h:ASCA-SIS1-BRIGHT > filter pha_cut 0 547
!ad55000030s100202h:ASCA-SIS1-BRIGHT > extract image
!ad55000030s100202h:ASCA-SIS1-BRIGHT > save image outfile=ad55000030s100202h_lo.img
Wrote image to file ad55000030s100202h_lo.img
!ad55000030s100202h:ASCA-SIS1-BRIGHT > clear pha_cut
!ad55000030s100202h:ASCA-SIS1-BRIGHT > filter pha_cut 547 2048
Warning: your PI upper bound: 2048 is above the maximum value.
!ad55000030s100202h:ASCA-SIS1-BRIGHT > extract image
!ad55000030s100202h:ASCA-SIS1-BRIGHT > save image outfile=ad55000030s100202h_hi.img
Wrote image to file ad55000030s100202h_hi.img
!ad55000030s100202h:ASCA-SIS1-BRIGHT > exit save_session=no
-> Generating exposure map ad55000030s100302m.expo
ASCAEXPO_V0.9b
reading data file: ad55000030s100302m.evt
reading gti ext: STDGTI
reading hp ext: HOT_PIXELS
reading cal file: s1_teldef_ascalin.fits
making an inst map...
SIS AREA DISC ENABL OFF
CHIP: 0 1 2 3
CCD POWER ON/OFF: ON ON ON ON
AREA DISC IN/OUT: OUT OUT OUT OUT
AREA DISC H START: 6 6 6 6
AREA DISC H STOP: 425 425 425 103
AREA DISC V START: 2 2 2 2
AREA DISC V STOP: 422 422 422 422
reading att file: ./fa970409_2051.0625
making an exposure map...
Aspect RA/DEC/ROLL : 275.6770 -13.7019 284.7644
Mean RA/DEC/ROLL : 275.6770 -13.7137 284.7644
Pnt RA/DEC/ROLL : 275.6700 -13.7185 284.7644
Image rebin factor : 4
Attitude Records : 46381
Hot Pixels : 26
GTI intervals : 1
Total GTI (secs) : 80.003
Max attitude excursion (arcsecs) : 5.000
0 Percent Complete: Total/live time: 0.0000000 0.0000000
10 Percent Complete: Total/live time: 80.0027237 80.0027237
100 Percent Complete: Total/live time: 80.0027237 80.0027237
Number of attitude steps used: 2
Number of attitude steps avail: 61
Mean RA/DEC pixel offset: -31.7297 0.1410
writing expo file: ad55000030s100302m.expo
closing attitude file...
closing data file...
-> Generating low and high energy images for ad55000030s100302m.evt
** XSELECT V1.3 **
!> Enter session name >[xsel] ad55000030s100302m
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS S1CCDPOW
1 GAL_RIDG BRIGHT MEDIUM 09/04/97 20:51:26 0.80E+02 57 1111
EXTRACTOR vers 2.0 11 Apr 1997.
Getting FITS WCS Keywords
Doing file: /data/data16/seq_proc/55000030.005/ad55000030s100302m.evt
Total Good Bad: Region Time Phase Cut
57 57 0 0 0 0
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
57 57 0 0 0 0
in 80.00 seconds
Image has 57 counts for 0.7125 counts/sec
EXTRACTOR vers 2.0 11 Apr 1997.
Getting FITS WCS Keywords
Doing file: /data/data16/seq_proc/55000030.005/ad55000030s100302m.evt
Total Good Bad: Region Time Phase Cut
57 45 0 0 0 12
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
57 45 0 0 0 12
in 80.00 seconds
Image has 45 counts for 0.5625 counts/sec
EXTRACTOR vers 2.0 11 Apr 1997.
Getting FITS WCS Keywords
Doing file: /data/data16/seq_proc/55000030.005/ad55000030s100302m.evt
Total Good Bad: Region Time Phase Cut
57 13 0 0 0 44
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
57 13 0 0 0 44
in 80.00 seconds
Image has 13 counts for 0.1625 counts/sec
Command not found; type ? for a command listing
!ad55000030s100302m:ASCA >
!ad55000030s100302m:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!ad55000030s100302m:ASCA > set datadir .
Setting data directory to /data/data16/seq_proc/55000030.005/
Setting mkf directory to /data/data16/seq_proc/55000030.005/
!ad55000030s100302m:ASCA > read events ad55000030s100302m.evt
Got new instrument: SIS1
Setting: IMAGE binning = 4
WMAP binning = 8
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 2047
Got the minimum time resolution of the read data: 16.000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data16/seq_proc/55000030.005/
HK Directory is: /data/data16/seq_proc/55000030.005/
!ad55000030s100302m:ASCA-SIS1-BRIGHT > set image sky
!ad55000030s100302m:ASCA-SIS1-BRIGHT > filter region corner_point.reg
!ad55000030s100302m:ASCA-SIS1-BRIGHT > extract image
!ad55000030s100302m:ASCA-SIS1-BRIGHT > save image outfile=ad55000030s100302m.img
Wrote image to file ad55000030s100302m.img
!ad55000030s100302m:ASCA-SIS1-BRIGHT > filter pha_cut 0 547
!ad55000030s100302m:ASCA-SIS1-BRIGHT > extract image
!ad55000030s100302m:ASCA-SIS1-BRIGHT > save image outfile=ad55000030s100302m_lo.img
Wrote image to file ad55000030s100302m_lo.img
!ad55000030s100302m:ASCA-SIS1-BRIGHT > clear pha_cut
!ad55000030s100302m:ASCA-SIS1-BRIGHT > filter pha_cut 547 2048
Warning: your PI upper bound: 2048 is above the maximum value.
!ad55000030s100302m:ASCA-SIS1-BRIGHT > extract image
!ad55000030s100302m:ASCA-SIS1-BRIGHT > save image outfile=ad55000030s100302m_hi.img
Wrote image to file ad55000030s100302m_hi.img
!ad55000030s100302m:ASCA-SIS1-BRIGHT > exit save_session=no
-> Summing sis imagesad55000030s000102h.expo ad55000030s000202h.expo ad55000030s000302m.expo ad55000030s100102h.expo ad55000030s100202h.expo ad55000030s100302m.expo-> Summing the following images to produce ad55000030sis32002_all.totsky
ad55000030s000102h.img ad55000030s000202h.img ad55000030s000302m.img ad55000030s100102h.img ad55000030s100202h.img ad55000030s100302m.img-> Summing the following images to produce ad55000030sis32002_lo.totsky
ad55000030s000102h_lo.img ad55000030s000202h_lo.img ad55000030s000302m_lo.img ad55000030s100102h_lo.img ad55000030s100202h_lo.img ad55000030s100302m_lo.img-> Summing the following images to produce ad55000030sis32002_hi.totsky
ad55000030s000102h_hi.img ad55000030s000202h_hi.img ad55000030s000302m_hi.img ad55000030s100102h_hi.img ad55000030s100202h_hi.img ad55000030s100302m_hi.img-> Running XIMAGE to create ad55000030sis32002.gif
No of detectors read in: 20 ![1]XIMAGE> read/fits ad55000030sis32002_all.totsky Reading an image Telescope ASCA SIS0 Image display size = 320 Done, closing file Largest, Smallest 4.00000 0. Bscale, Bzero from file 1.0000000000000 0. After internal scaling Bscale and Bzero 1.0000000000000 0. Image level, max: 4 min: 0 ![2]XIMAGE> read/exp_map ad55000030sis32002.totexpo Reading an image Telescope ASCA SIS0 Image display size = 320 Done, closing file Largest, Smallest 234.791 0. Bscale, Bzero from file 1.0000000000000 0. After internal scaling Bscale and Bzero 1.0000000000000 0. Image level, max: 234 min: 0 ![3]XIMAGE> smooth ![4]XIMAGE> cpd /ppm ![5]XIMAGE> cey 2000 ![6]XIMAGE> disp/correct/noframe Displaying image The image is exposure corrected Min = 0 max = 3609 ![7]XIMAGE> grid ![8]XIMAGE> scale scal_f, min_inten 1.00000 0. i,inten,mm,pp 1 0. 0 0 i,inten,mm,pp 2 4.00000 40 -1 i,inten,mm,pp 3 9.00000 90 -1 i,inten,mm,pp 4 28.0000 28 0 ![9]XIMAGE> exit-> Summing gis images
ad55000030g200170h.expo ad55000030g300170h.expo-> Summing the following images to produce ad55000030gis25670_all.totsky
ad55000030g200170h.img ad55000030g300170h.img-> Summing the following images to produce ad55000030gis25670_lo.totsky
ad55000030g200170h_lo.img ad55000030g300170h_lo.img-> Summing the following images to produce ad55000030gis25670_hi.totsky
ad55000030g200170h_hi.img ad55000030g300170h_hi.img-> Running XIMAGE to create ad55000030gis25670.gif
No of detectors read in: 20 ![1]XIMAGE> read/fits ad55000030gis25670_all.totsky Reading an image Telescope ASCA GIS2 Image display size = 256 Done, closing file Largest, Smallest 5.00000 0. Bscale, Bzero from file 1.0000000000000 0. After internal scaling Bscale and Bzero 1.0000000000000 0. Image level, max: 5 min: 0 ![2]XIMAGE> read/exp_map ad55000030gis25670.totexpo Reading an image Telescope ASCA GIS2 Image display size = 256 Done, closing file Largest, Smallest 259.741 0. Bscale, Bzero from file 1.0000000000000 0. After internal scaling Bscale and Bzero 1.0000000000000 0. Image level, max: 259 min: 0 ![3]XIMAGE> smooth ![4]XIMAGE> cpd /ppm ![5]XIMAGE> cey 2000 ![6]XIMAGE> disp/correct/noframe Displaying image The image is exposure corrected Min = 0 max = 32767 ![7]XIMAGE> grid ![8]XIMAGE> scale scal_f, min_inten 1.00000 0. i,inten,mm,pp 1 0. 0 0 i,inten,mm,pp 2 4.00000 40 -1 i,inten,mm,pp 3 8.00000 80 -1 i,inten,mm,pp 4 26.0000 26 0 ![9]XIMAGE> exit
color plane 0 color plane 1 color plane 2 writing image image written-> Creating fits catalog of sources: ad55000030gis25670.src
color plane 0 color plane 1 color plane 2 writing image image written-> Creating fits catalog of sources: ad55000030sis32002.src
1 ad55000030s000202h.evt 1099 1 ad55000030s000302m.evt 1099 2 ad55000030s000102h.evt 137-> Fetching SIS0_OFFCHIP.1
ad55000030s000202h.evt ad55000030s000302m.evt-> Standard Output From FTOOL xselect:
** XSELECT V1.3 **
!> Enter session name >[xsel] xsel
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS S0CCDPOW
1 GAL_RIDG BRIGHT HIGH 09/04/97 21:02:58 0.65E+04 1022 1111
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS S0CCDPOW
1 GAL_RIDG BRIGHT HIGH 09/04/97 21:02:58 0.65E+04 1022 1111
2 GAL_RIDG BRIGHT MEDIUM 09/04/97 20:51:26 0.80E+02 77 1111
EXTRACTOR vers 2.0 11 Apr 1997.
Getting FITS WCS Keywords
Doing file: /data/data16/seq_proc/55000030.005/ad55000030s000202h.evt
Total Good Bad: Region Time Phase Cut
1022 997 25 0 0 0
Doing file: /data/data16/seq_proc/55000030.005/ad55000030s000302m.evt
Total Good Bad: Region Time Phase Cut
77 74 3 0 0 0
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
1099 1071 28 0 0 0
in 6569.46 seconds
Spectrum has 1071 counts for 0.1630 counts/sec
-------------------------
MANDATORY KEYWORDS/VALUES
-------------------------
--------------------------------------------------------------------
--------------------------------------------------------------------
EXTNAME - SPECTRUM Name of this BINTABLE
TELESCOP - ASCA Mission/Satellite name
INSTRUME - SIS0 Instrument/Detector
FILTER - Instrument filter in use
EXPOSURE - 6569.5 Integration time (in secs) of PHA data
AREASCAL - 1.0000 Area scaling factor
BACKSCAL - 0.47331 Background scaling factor
BACKFILE - NONE Associated background file
CORRSCAL - 1.0000 Correlation scaling factor
CORRFILE - none Associated correlation file
RESPFILE - NONE Associated redistribution matrix file
ANCRFILE - none Associated ancillary response file
XFLT0001 - none XSPEC selection filter
POISSERR - TRUE Whether Poissonian errors apply
CHANTYPE - PI Whether channels have been corrected
TLMIN1 - 0 First legal Detector channel
DETCHANS - 512 No. of legal detector channels
NCHAN - 512 No. of detector channels in dataset
PHAVERSN - 1.1.0 OGIP FITS version number
STAT_ERR - FALSE Statistical Error
SYS_ERR - TRUE Fractional Systematic Error
QUALITY - TRUE Quality Flag
GROUPING - FALSE Grouping Flag
--------------------------------------------------------------------
--------------------------------------------------------------------
... QUALITY
...
... -------
... QUALITY
... -------
... Bad Channels (Channel - Channel)
... ---------------------------------------------
... 0 - 15 have quality 5
... ---------------------------------------------
...
...... exiting, changes written to file : ad55000030s010102_0.pi
EXTRACTOR vers 2.0 11 Apr 1997.
Doing file: /data/data16/seq_proc/55000030.005/ad55000030s000202h.evt
Total Good Bad: Region Time Phase Cut
1022 997 25 0 0 0
Writing events file
997 events written to the output file
Doing file: /data/data16/seq_proc/55000030.005/ad55000030s000302m.evt
Total Good Bad: Region Time Phase Cut
77 74 3 0 0 0
Writing events file
1071 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
1099 1071 28 0 0 0
in 6569.46 seconds
Command not found; type ? for a command listing
!xsel:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!xsel:ASCA > set datadir .
Setting data directory to /data/data16/seq_proc/55000030.005/
Setting mkf directory to /data/data16/seq_proc/55000030.005/
!xsel:ASCA > read events ad55000030s000202h.evt
Got new instrument: SIS0
Setting: IMAGE binning = 4
WMAP binning = 8
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 2047
Got the minimum time resolution of the read data: 16.000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data16/seq_proc/55000030.005/
HK Directory is: /data/data16/seq_proc/55000030.005/
!xsel:ASCA-SIS0-BRIGHT > read events ad55000030s000302m.evt
Getting Min and Max for Energy Column...
Got min and max for PI: 0 2047
Got the minimum time resolution of the read data: 16.000
Number of files read in: 2
******************** Observation Catalogue ********************
Data Directory is: /data/data16/seq_proc/55000030.005/
HK Directory is: /data/data16/seq_proc/55000030.005/
!xsel:ASCA-SIS0-BRIGHT > set phaname PI
!xsel:ASCA-SIS0-BRIGHT > filter region ad55000030s032002_0.reg
!xsel:ASCA-SIS0-BRIGHT > filter region SIS0_OFFCHIP.1
!xsel:ASCA-SIS0-BRIGHT > filter region ad55000030s010102.discrim
!xsel:ASCA-SIS0-BRIGHT > extract spectrum
!xsel:ASCA-SIS0-BRIGHT > save spectrum ad55000030s010102_0.pi group=yes
Wrote spectrum to ad55000030s010102_0.pi
!xsel:ASCA-SIS0-BRIGHT > extract events
!xsel:ASCA-SIS0-BRIGHT > save events outfile=events.tmp use_events=yes
Wrote events list to file events.tmp
Changing Data directory from:
/data/data16/seq_proc/55000030.005/
to the current working directory.
!xsel:ASCA-SIS0-BRIGHT > exit save_session=no
-> Grouping ad55000030s010102_0.pi to 40 counts/bin------------------------- MANDATORY KEYWORDS/VALUES ------------------------- -------------------------------------------------------------------- -------------------------------------------------------------------- EXTNAME - SPECTRUM Name of this BINTABLE TELESCOP - ASCA Mission/Satellite name INSTRUME - SIS0 Instrument/Detector FILTER - Instrument filter in use EXPOSURE - 6569.5 Integration time (in secs) of PHA data AREASCAL - 1.0000 Area scaling factor BACKSCAL - 0.47331 Background scaling factor BACKFILE - NONE Associated background file CORRSCAL - 1.0000 Correlation scaling factor CORRFILE - none Associated correlation file RESPFILE - NONE Associated redistribution matrix file ANCRFILE - none Associated ancillary response file XFLT0001 - none XSPEC selection filter POISSERR - TRUE Whether Poissonian errors apply CHANTYPE - PI Whether channels have been corrected TLMIN1 - 0 First legal Detector channel DETCHANS - 512 No. of legal detector channels NCHAN - 512 No. of detector channels in dataset PHAVERSN - 1.1.0 OGIP FITS version number STAT_ERR - FALSE Statistical Error SYS_ERR - TRUE Fractional Systematic Error QUALITY - TRUE Quality Flag GROUPING - FALSE Grouping Flag -------------------------------------------------------------------- -------------------------------------------------------------------- ... ... -------- ... GROUPING ... -------- ... --------------------------------------------- ... Channel Grouping (Channel-Channel) : ... 0 - 15 of undefined grouping (Channel quality=bad) ... 16 - 42 are grouped by a factor 27 ... 43 - 50 are grouped by a factor 4 ... 51 - 62 are grouped by a factor 3 ... 63 - 66 are grouped by a factor 4 ... 67 - 71 are grouped by a factor 5 ... 72 - 74 are grouped by a factor 3 ... 75 - 78 are grouped by a factor 4 ... 79 - 83 are grouped by a factor 5 ... 84 - 90 are grouped by a factor 7 ... 91 - 98 are grouped by a factor 8 ... 99 - 105 are grouped by a factor 7 ... 106 - 111 are grouped by a factor 6 ... 112 - 120 are grouped by a factor 9 ... 121 - 130 are grouped by a factor 10 ... 131 - 141 are grouped by a factor 11 ... 142 - 162 are grouped by a factor 21 ... 163 - 182 are grouped by a factor 20 ... 183 - 226 are grouped by a factor 44 ... 227 - 296 are grouped by a factor 70 ... 297 - 511 of undefined grouping (Channel quality=bad) ... --------------------------------------------- ... ...... exiting, changes written to file : ad55000030s010102_0.pi ** grppha 2.6.0 completed successfully-> Source occupies chip(s) 0 1 2 3
** XSELECT V1.3 **
!> Enter session name >[xsel] xsel
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS S0CCDPOW
1 GAL_RIDG BRIGHT HIGH 09/04/97 20:51:26 0.66E+04 1071 1111
EXTRACTOR vers 2.0 11 Apr 1997.
Getting FITS WCS Keywords
Doing file: /data/data16/seq_proc/55000030.005/events.tmp
Total Good Bad: Region Time Phase Cut
1071 266 805 0 0 0
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
1071 266 805 0 0 0
in 6569.46 seconds
Spectrum has 266 counts for 4.0490E-02 counts/sec
-------------------------
MANDATORY KEYWORDS/VALUES
-------------------------
--------------------------------------------------------------------
--------------------------------------------------------------------
EXTNAME - SPECTRUM Name of this BINTABLE
TELESCOP - ASCA Mission/Satellite name
INSTRUME - SIS0 Instrument/Detector
FILTER - Instrument filter in use
EXPOSURE - 6569.5 Integration time (in secs) of PHA data
AREASCAL - 1.0000 Area scaling factor
BACKSCAL - 0.15946 Background scaling factor
BACKFILE - NONE Associated background file
CORRSCAL - 1.0000 Correlation scaling factor
CORRFILE - none Associated correlation file
RESPFILE - NONE Associated redistribution matrix file
ANCRFILE - none Associated ancillary response file
XFLT0001 - none XSPEC selection filter
POISSERR - TRUE Whether Poissonian errors apply
CHANTYPE - PI Whether channels have been corrected
TLMIN1 - 0 First legal Detector channel
DETCHANS - 512 No. of legal detector channels
NCHAN - 512 No. of detector channels in dataset
PHAVERSN - 1.1.0 OGIP FITS version number
STAT_ERR - FALSE Statistical Error
SYS_ERR - TRUE Fractional Systematic Error
QUALITY - TRUE Quality Flag
GROUPING - FALSE Grouping Flag
--------------------------------------------------------------------
--------------------------------------------------------------------
... QUALITY
...
... -------
... QUALITY
... -------
... Bad Channels (Channel - Channel)
... ---------------------------------------------
... 0 - 15 have quality 5
... ---------------------------------------------
...
...... exiting, changes written to file : spec0.tmp
Command not found; type ? for a command listing
!xsel:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!xsel:ASCA > set datadir .
Setting data directory to /data/data16/seq_proc/55000030.005/
Setting mkf directory to /data/data16/seq_proc/55000030.005/
!xsel:ASCA > read events events.tmp
Got new instrument: SIS0
Setting: IMAGE binning = 4
WMAP binning = 8
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 2047
Got the minimum time resolution of the read data: 16.000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data16/seq_proc/55000030.005/
HK Directory is: /data/data16/seq_proc/55000030.005/
!xsel:ASCA-SIS0-BRIGHT > set phaname PI
!xsel:ASCA-SIS0-BRIGHT > filter region ad55000030s032002_0.reg
!xsel:ASCA-SIS0-BRIGHT > filter region SIS0_OFFCHIP.1
!xsel:ASCA-SIS0-BRIGHT > filter region ad55000030s010102.discrim
!xsel:ASCA-SIS0-BRIGHT > filter region SIS0_NOTCHIP1.1
!xsel:ASCA-SIS0-BRIGHT > filter region SIS0_NOTCHIP2.1
!xsel:ASCA-SIS0-BRIGHT > filter region SIS0_NOTCHIP3.1
!xsel:ASCA-SIS0-BRIGHT > extract spectrum
!xsel:ASCA-SIS0-BRIGHT > save spectrum spec0.tmp group=yes
Wrote spectrum to spec0.tmp
!xsel:ASCA-SIS0-BRIGHT > exit save_session=no
-> Fetching sis0c0p40_290296.fitsSisrmg Version 1.1, Configured 04/97 This version resolves *all* known keyword incompatibilities with other FTOOLS tasks. If you have previously fudged *any* keywords in the PHA file to compensate, incorrect results will follow. Setting 1st PHA channel to 0 Making v1.1 1180x512 S0C0 Bright PI RMF Calibration data from ./ Please stand by... ...Done.-> Fetching SIS0_NOTCHIP0.1
** XSELECT V1.3 **
!> Enter session name >[xsel] xsel
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS S0CCDPOW
1 GAL_RIDG BRIGHT HIGH 09/04/97 20:51:26 0.66E+04 1071 1111
EXTRACTOR vers 2.0 11 Apr 1997.
Getting FITS WCS Keywords
Doing file: /data/data16/seq_proc/55000030.005/events.tmp
Total Good Bad: Region Time Phase Cut
1071 311 760 0 0 0
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
1071 311 760 0 0 0
in 6569.46 seconds
Spectrum has 311 counts for 4.7340E-02 counts/sec
-------------------------
MANDATORY KEYWORDS/VALUES
-------------------------
--------------------------------------------------------------------
--------------------------------------------------------------------
EXTNAME - SPECTRUM Name of this BINTABLE
TELESCOP - ASCA Mission/Satellite name
INSTRUME - SIS0 Instrument/Detector
FILTER - Instrument filter in use
EXPOSURE - 6569.5 Integration time (in secs) of PHA data
AREASCAL - 1.0000 Area scaling factor
BACKSCAL - 0.15947 Background scaling factor
BACKFILE - NONE Associated background file
CORRSCAL - 1.0000 Correlation scaling factor
CORRFILE - none Associated correlation file
RESPFILE - NONE Associated redistribution matrix file
ANCRFILE - none Associated ancillary response file
XFLT0001 - none XSPEC selection filter
POISSERR - TRUE Whether Poissonian errors apply
CHANTYPE - PI Whether channels have been corrected
TLMIN1 - 0 First legal Detector channel
DETCHANS - 512 No. of legal detector channels
NCHAN - 512 No. of detector channels in dataset
PHAVERSN - 1.1.0 OGIP FITS version number
STAT_ERR - FALSE Statistical Error
SYS_ERR - TRUE Fractional Systematic Error
QUALITY - TRUE Quality Flag
GROUPING - FALSE Grouping Flag
--------------------------------------------------------------------
--------------------------------------------------------------------
... QUALITY
...
... -------
... QUALITY
... -------
... Bad Channels (Channel - Channel)
... ---------------------------------------------
... 0 - 15 have quality 5
... ---------------------------------------------
...
...... exiting, changes written to file : spec1.tmp
Command not found; type ? for a command listing
!xsel:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!xsel:ASCA > set datadir .
Setting data directory to /data/data16/seq_proc/55000030.005/
Setting mkf directory to /data/data16/seq_proc/55000030.005/
!xsel:ASCA > read events events.tmp
Got new instrument: SIS0
Setting: IMAGE binning = 4
WMAP binning = 8
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 2047
Got the minimum time resolution of the read data: 16.000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data16/seq_proc/55000030.005/
HK Directory is: /data/data16/seq_proc/55000030.005/
!xsel:ASCA-SIS0-BRIGHT > set phaname PI
!xsel:ASCA-SIS0-BRIGHT > filter region ad55000030s032002_0.reg
!xsel:ASCA-SIS0-BRIGHT > filter region SIS0_OFFCHIP.1
!xsel:ASCA-SIS0-BRIGHT > filter region ad55000030s010102.discrim
!xsel:ASCA-SIS0-BRIGHT > filter region SIS0_NOTCHIP0.1
!xsel:ASCA-SIS0-BRIGHT > filter region SIS0_NOTCHIP2.1
!xsel:ASCA-SIS0-BRIGHT > filter region SIS0_NOTCHIP3.1
!xsel:ASCA-SIS0-BRIGHT > extract spectrum
!xsel:ASCA-SIS0-BRIGHT > save spectrum spec1.tmp group=yes
Wrote spectrum to spec1.tmp
!xsel:ASCA-SIS0-BRIGHT > exit save_session=no
-> Fetching sis0c1p40_290296.fitsSisrmg Version 1.1, Configured 04/97 This version resolves *all* known keyword incompatibilities with other FTOOLS tasks. If you have previously fudged *any* keywords in the PHA file to compensate, incorrect results will follow. Setting 1st PHA channel to 0 Making v1.1 1180x512 S0C1 Bright PI RMF Calibration data from ./ Please stand by... ...Done.-> SIS0_NOTCHIP0.1 already present in current directory
** XSELECT V1.3 **
!> Enter session name >[xsel] xsel
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS S0CCDPOW
1 GAL_RIDG BRIGHT HIGH 09/04/97 20:51:26 0.66E+04 1071 1111
EXTRACTOR vers 2.0 11 Apr 1997.
Getting FITS WCS Keywords
Doing file: /data/data16/seq_proc/55000030.005/events.tmp
Total Good Bad: Region Time Phase Cut
1071 220 851 0 0 0
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
1071 220 851 0 0 0
in 6569.46 seconds
Spectrum has 220 counts for 3.3488E-02 counts/sec
-------------------------
MANDATORY KEYWORDS/VALUES
-------------------------
--------------------------------------------------------------------
--------------------------------------------------------------------
EXTNAME - SPECTRUM Name of this BINTABLE
TELESCOP - ASCA Mission/Satellite name
INSTRUME - SIS0 Instrument/Detector
FILTER - Instrument filter in use
EXPOSURE - 6569.5 Integration time (in secs) of PHA data
AREASCAL - 1.0000 Area scaling factor
BACKSCAL - 0.15997 Background scaling factor
BACKFILE - NONE Associated background file
CORRSCAL - 1.0000 Correlation scaling factor
CORRFILE - none Associated correlation file
RESPFILE - NONE Associated redistribution matrix file
ANCRFILE - none Associated ancillary response file
XFLT0001 - none XSPEC selection filter
POISSERR - TRUE Whether Poissonian errors apply
CHANTYPE - PI Whether channels have been corrected
TLMIN1 - 0 First legal Detector channel
DETCHANS - 512 No. of legal detector channels
NCHAN - 512 No. of detector channels in dataset
PHAVERSN - 1.1.0 OGIP FITS version number
STAT_ERR - FALSE Statistical Error
SYS_ERR - TRUE Fractional Systematic Error
QUALITY - TRUE Quality Flag
GROUPING - FALSE Grouping Flag
--------------------------------------------------------------------
--------------------------------------------------------------------
... QUALITY
...
... -------
... QUALITY
... -------
... Bad Channels (Channel - Channel)
... ---------------------------------------------
... 0 - 15 have quality 5
... ---------------------------------------------
...
...... exiting, changes written to file : spec2.tmp
Command not found; type ? for a command listing
!xsel:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!xsel:ASCA > set datadir .
Setting data directory to /data/data16/seq_proc/55000030.005/
Setting mkf directory to /data/data16/seq_proc/55000030.005/
!xsel:ASCA > read events events.tmp
Got new instrument: SIS0
Setting: IMAGE binning = 4
WMAP binning = 8
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 2047
Got the minimum time resolution of the read data: 16.000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data16/seq_proc/55000030.005/
HK Directory is: /data/data16/seq_proc/55000030.005/
!xsel:ASCA-SIS0-BRIGHT > set phaname PI
!xsel:ASCA-SIS0-BRIGHT > filter region ad55000030s032002_0.reg
!xsel:ASCA-SIS0-BRIGHT > filter region SIS0_OFFCHIP.1
!xsel:ASCA-SIS0-BRIGHT > filter region ad55000030s010102.discrim
!xsel:ASCA-SIS0-BRIGHT > filter region SIS0_NOTCHIP0.1
!xsel:ASCA-SIS0-BRIGHT > filter region SIS0_NOTCHIP1.1
!xsel:ASCA-SIS0-BRIGHT > filter region SIS0_NOTCHIP3.1
!xsel:ASCA-SIS0-BRIGHT > extract spectrum
!xsel:ASCA-SIS0-BRIGHT > save spectrum spec2.tmp group=yes
Wrote spectrum to spec2.tmp
!xsel:ASCA-SIS0-BRIGHT > exit save_session=no
-> Fetching sis0c2p40_290296.fitsSisrmg Version 1.1, Configured 04/97 This version resolves *all* known keyword incompatibilities with other FTOOLS tasks. If you have previously fudged *any* keywords in the PHA file to compensate, incorrect results will follow. Setting 1st PHA channel to 0 Making v1.1 1180x512 S0C2 Bright PI RMF Calibration data from ./ Please stand by... ...Done.-> SIS0_NOTCHIP0.1 already present in current directory
** XSELECT V1.3 **
!> Enter session name >[xsel] xsel
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS S0CCDPOW
1 GAL_RIDG BRIGHT HIGH 09/04/97 20:51:26 0.66E+04 1071 1111
EXTRACTOR vers 2.0 11 Apr 1997.
Getting FITS WCS Keywords
Doing file: /data/data16/seq_proc/55000030.005/events.tmp
Total Good Bad: Region Time Phase Cut
1071 274 797 0 0 0
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
1071 274 797 0 0 0
in 6569.46 seconds
Spectrum has 274 counts for 4.1708E-02 counts/sec
-------------------------
MANDATORY KEYWORDS/VALUES
-------------------------
--------------------------------------------------------------------
--------------------------------------------------------------------
EXTNAME - SPECTRUM Name of this BINTABLE
TELESCOP - ASCA Mission/Satellite name
INSTRUME - SIS0 Instrument/Detector
FILTER - Instrument filter in use
EXPOSURE - 6569.5 Integration time (in secs) of PHA data
AREASCAL - 1.0000 Area scaling factor
BACKSCAL - 0.15896 Background scaling factor
BACKFILE - NONE Associated background file
CORRSCAL - 1.0000 Correlation scaling factor
CORRFILE - none Associated correlation file
RESPFILE - NONE Associated redistribution matrix file
ANCRFILE - none Associated ancillary response file
XFLT0001 - none XSPEC selection filter
POISSERR - TRUE Whether Poissonian errors apply
CHANTYPE - PI Whether channels have been corrected
TLMIN1 - 0 First legal Detector channel
DETCHANS - 512 No. of legal detector channels
NCHAN - 512 No. of detector channels in dataset
PHAVERSN - 1.1.0 OGIP FITS version number
STAT_ERR - FALSE Statistical Error
SYS_ERR - TRUE Fractional Systematic Error
QUALITY - TRUE Quality Flag
GROUPING - FALSE Grouping Flag
--------------------------------------------------------------------
--------------------------------------------------------------------
... QUALITY
...
... -------
... QUALITY
... -------
... Bad Channels (Channel - Channel)
... ---------------------------------------------
... 0 - 15 have quality 5
... ---------------------------------------------
...
...... exiting, changes written to file : spec3.tmp
Command not found; type ? for a command listing
!xsel:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!xsel:ASCA > set datadir .
Setting data directory to /data/data16/seq_proc/55000030.005/
Setting mkf directory to /data/data16/seq_proc/55000030.005/
!xsel:ASCA > read events events.tmp
Got new instrument: SIS0
Setting: IMAGE binning = 4
WMAP binning = 8
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 2047
Got the minimum time resolution of the read data: 16.000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data16/seq_proc/55000030.005/
HK Directory is: /data/data16/seq_proc/55000030.005/
!xsel:ASCA-SIS0-BRIGHT > set phaname PI
!xsel:ASCA-SIS0-BRIGHT > filter region ad55000030s032002_0.reg
!xsel:ASCA-SIS0-BRIGHT > filter region SIS0_OFFCHIP.1
!xsel:ASCA-SIS0-BRIGHT > filter region ad55000030s010102.discrim
!xsel:ASCA-SIS0-BRIGHT > filter region SIS0_NOTCHIP0.1
!xsel:ASCA-SIS0-BRIGHT > filter region SIS0_NOTCHIP1.1
!xsel:ASCA-SIS0-BRIGHT > filter region SIS0_NOTCHIP2.1
!xsel:ASCA-SIS0-BRIGHT > extract spectrum
!xsel:ASCA-SIS0-BRIGHT > save spectrum spec3.tmp group=yes
Wrote spectrum to spec3.tmp
!xsel:ASCA-SIS0-BRIGHT > exit save_session=no
-> Fetching sis0c3p40_290296.fitsSisrmg Version 1.1, Configured 04/97 This version resolves *all* known keyword incompatibilities with other FTOOLS tasks. If you have previously fudged *any* keywords in the PHA file to compensate, incorrect results will follow. Setting 1st PHA channel to 0 Making v1.1 1180x512 S0C3 Bright PI RMF Calibration data from ./ Please stand by... ...Done.-> Chip weights:
rmf0.tmp 0.248366013071895 rmf1.tmp 0.290382819794585 rmf2.tmp 0.205415499533147 rmf3.tmp 0.255835667600373-> Standard Output From FTOOL addrmf:
ADDRMF vers 1.10 10 April, 1997.
Summing ...
2.484E-01 * rmf0.tmp
2.904E-01 * rmf1.tmp
2.054E-01 * rmf2.tmp
2.558E-01 * rmf3.tmp
RMF # 1 : rmf0.tmp 0.25
ASCA SIS0 NONE NONE PI
RMF # 2 : rmf1.tmp 0.29
ASCA SIS0 NONE NONE PI
RMF # 3 : rmf2.tmp 0.21
ASCA SIS0 NONE NONE PI
RMF # 4 : rmf3.tmp 0.26
ASCA SIS0 NONE NONE PI
-> Generating ad55000030s010102_0.arf with point=no
ASCAARF vers 2.72 14 Mar 1997.
Input WMAP array has size 105 by 134 bins
expanded to 105 by 134 bins
First WMAP bin is at detector pixel 224 208
8 detector pixels per WMAP bin
WMAP bin size is 0.21600 mm
0.21216 arcmin
Selected region size is 545.40 arcmin^2
Optical axis is detector pixel 662.72 559.02
1180 energies from RMF file
Effective area fudge applied
Arf filter applied
Total counts in region = 1.04600E+03
Weighted mean angle from optical axis = 8.717 arcmin
-> Standard Output From STOOL group_event_files:1 ad55000030s000212h.evt 1464 2 ad55000030s000112h.evt 151-> SIS0_OFFCHIP.1 already present in current directory
ad55000030s000212h.evt-> Standard Output From FTOOL xselect:
** XSELECT V1.3 **
!> Enter session name >[xsel] xsel
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS S0CCDPOW
1 GAL_RIDG BRIGHT2 HIGH 09/04/97 21:02:58 0.65E+04 1464 1111
EXTRACTOR vers 2.0 11 Apr 1997.
Getting FITS WCS Keywords
Doing file: /data/data16/seq_proc/55000030.005/ad55000030s000212h.evt
Total Good Bad: Region Time Phase Cut
1464 1426 38 0 0 0
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
1464 1426 38 0 0 0
in 6489.46 seconds
Spectrum has 1426 counts for 0.2197 counts/sec
-------------------------
MANDATORY KEYWORDS/VALUES
-------------------------
--------------------------------------------------------------------
--------------------------------------------------------------------
EXTNAME - SPECTRUM Name of this BINTABLE
TELESCOP - ASCA Mission/Satellite name
INSTRUME - SIS0 Instrument/Detector
FILTER - Instrument filter in use
EXPOSURE - 6489.5 Integration time (in secs) of PHA data
AREASCAL - 1.0000 Area scaling factor
BACKSCAL - 0.47331 Background scaling factor
BACKFILE - NONE Associated background file
CORRSCAL - 1.0000 Correlation scaling factor
CORRFILE - none Associated correlation file
RESPFILE - NONE Associated redistribution matrix file
ANCRFILE - none Associated ancillary response file
XFLT0001 - none XSPEC selection filter
POISSERR - TRUE Whether Poissonian errors apply
CHANTYPE - PI Whether channels have been corrected
TLMIN1 - 0 First legal Detector channel
DETCHANS - 1024 No. of legal detector channels
NCHAN - 1024 No. of detector channels in dataset
PHAVERSN - 1.1.0 OGIP FITS version number
STAT_ERR - FALSE Statistical Error
SYS_ERR - TRUE Fractional Systematic Error
QUALITY - TRUE Quality Flag
GROUPING - FALSE Grouping Flag
--------------------------------------------------------------------
--------------------------------------------------------------------
... QUALITY
...
... -------
... QUALITY
... -------
... Bad Channels (Channel - Channel)
... ---------------------------------------------
... 0 - 31 have quality 5
... ---------------------------------------------
...
...... exiting, changes written to file : ad55000030s010212_0.pi
EXTRACTOR vers 2.0 11 Apr 1997.
Doing file: /data/data16/seq_proc/55000030.005/ad55000030s000212h.evt
Total Good Bad: Region Time Phase Cut
1464 1426 38 0 0 0
Writing events file
1426 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
1464 1426 38 0 0 0
in 6489.46 seconds
Command not found; type ? for a command listing
!xsel:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!xsel:ASCA > set datadir .
Setting data directory to /data/data16/seq_proc/55000030.005/
Setting mkf directory to /data/data16/seq_proc/55000030.005/
!xsel:ASCA > read events ad55000030s000212h.evt
Got new instrument: SIS0
Setting: IMAGE binning = 4
WMAP binning = 8
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 4095
Got the minimum time resolution of the read data: 16.000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data16/seq_proc/55000030.005/
HK Directory is: /data/data16/seq_proc/55000030.005/
!xsel:ASCA-SIS0-BRIGHT2 > set phaname PI
!xsel:ASCA-SIS0-BRIGHT2 > filter region ad55000030s032002_0.reg
!xsel:ASCA-SIS0-BRIGHT2 > filter region SIS0_OFFCHIP.1
!xsel:ASCA-SIS0-BRIGHT2 > filter region ad55000030s010212.discrim
!xsel:ASCA-SIS0-BRIGHT2 > extract spectrum
!xsel:ASCA-SIS0-BRIGHT2 > save spectrum ad55000030s010212_0.pi group=yes
Wrote spectrum to ad55000030s010212_0.pi
!xsel:ASCA-SIS0-BRIGHT2 > extract events
!xsel:ASCA-SIS0-BRIGHT2 > save events outfile=events.tmp use_events=yes
Wrote events list to file events.tmp
Changing Data directory from:
/data/data16/seq_proc/55000030.005/
to the current working directory.
!xsel:ASCA-SIS0-BRIGHT2 > exit save_session=no
-> Grouping ad55000030s010212_0.pi to 40 counts/bin------------------------- MANDATORY KEYWORDS/VALUES ------------------------- -------------------------------------------------------------------- -------------------------------------------------------------------- EXTNAME - SPECTRUM Name of this BINTABLE TELESCOP - ASCA Mission/Satellite name INSTRUME - SIS0 Instrument/Detector FILTER - Instrument filter in use EXPOSURE - 6489.5 Integration time (in secs) of PHA data AREASCAL - 1.0000 Area scaling factor BACKSCAL - 0.47331 Background scaling factor BACKFILE - NONE Associated background file CORRSCAL - 1.0000 Correlation scaling factor CORRFILE - none Associated correlation file RESPFILE - NONE Associated redistribution matrix file ANCRFILE - none Associated ancillary response file XFLT0001 - none XSPEC selection filter POISSERR - TRUE Whether Poissonian errors apply CHANTYPE - PI Whether channels have been corrected TLMIN1 - 0 First legal Detector channel DETCHANS - 1024 No. of legal detector channels NCHAN - 1024 No. of detector channels in dataset PHAVERSN - 1.1.0 OGIP FITS version number STAT_ERR - FALSE Statistical Error SYS_ERR - TRUE Fractional Systematic Error QUALITY - TRUE Quality Flag GROUPING - FALSE Grouping Flag -------------------------------------------------------------------- -------------------------------------------------------------------- ... ... -------- ... GROUPING ... -------- ... --------------------------------------------- ... Channel Grouping (Channel-Channel) : ... 0 - 31 of undefined grouping (Channel quality=bad) ... 32 - 79 are grouped by a factor 48 ... 80 - 85 are grouped by a factor 6 ... 86 - 89 are grouped by a factor 4 ... 90 - 95 are grouped by a factor 6 ... 96 - 105 are grouped by a factor 5 ... 106 - 109 are grouped by a factor 4 ... 110 - 115 are grouped by a factor 6 ... 116 - 119 are grouped by a factor 4 ... 120 - 125 are grouped by a factor 6 ... 126 - 130 are grouped by a factor 5 ... 131 - 137 are grouped by a factor 7 ... 138 - 143 are grouped by a factor 6 ... 144 - 148 are grouped by a factor 5 ... 149 - 154 are grouped by a factor 6 ... 155 - 161 are grouped by a factor 7 ... 162 - 171 are grouped by a factor 10 ... 172 - 180 are grouped by a factor 9 ... 181 - 191 are grouped by a factor 11 ... 192 - 200 are grouped by a factor 9 ... 201 - 210 are grouped by a factor 10 ... 211 - 224 are grouped by a factor 14 ... 225 - 236 are grouped by a factor 12 ... 237 - 249 are grouped by a factor 13 ... 250 - 261 are grouped by a factor 12 ... 262 - 281 are grouped by a factor 20 ... 282 - 307 are grouped by a factor 26 ... 308 - 338 are grouped by a factor 31 ... 339 - 364 are grouped by a factor 26 ... 365 - 423 are grouped by a factor 59 ... 424 - 476 are grouped by a factor 53 ... 477 - 561 are grouped by a factor 85 ... 562 - 716 are grouped by a factor 155 ... 717 - 1023 of undefined grouping (Channel quality=bad) ... --------------------------------------------- ... ...... exiting, changes written to file : ad55000030s010212_0.pi ** grppha 2.6.0 completed successfully-> Source occupies chip(s) 0 1 2 3
** XSELECT V1.3 **
!> Enter session name >[xsel] xsel
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS S0CCDPOW
1 GAL_RIDG BRIGHT2 HIGH 09/04/97 21:02:58 0.65E+04 1426 1111
EXTRACTOR vers 2.0 11 Apr 1997.
Getting FITS WCS Keywords
Doing file: /data/data16/seq_proc/55000030.005/events.tmp
Total Good Bad: Region Time Phase Cut
1426 348 1078 0 0 0
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
1426 348 1078 0 0 0
in 6489.46 seconds
Spectrum has 348 counts for 5.3625E-02 counts/sec
-------------------------
MANDATORY KEYWORDS/VALUES
-------------------------
--------------------------------------------------------------------
--------------------------------------------------------------------
EXTNAME - SPECTRUM Name of this BINTABLE
TELESCOP - ASCA Mission/Satellite name
INSTRUME - SIS0 Instrument/Detector
FILTER - Instrument filter in use
EXPOSURE - 6489.5 Integration time (in secs) of PHA data
AREASCAL - 1.0000 Area scaling factor
BACKSCAL - 0.15946 Background scaling factor
BACKFILE - NONE Associated background file
CORRSCAL - 1.0000 Correlation scaling factor
CORRFILE - none Associated correlation file
RESPFILE - NONE Associated redistribution matrix file
ANCRFILE - none Associated ancillary response file
XFLT0001 - none XSPEC selection filter
POISSERR - TRUE Whether Poissonian errors apply
CHANTYPE - PI Whether channels have been corrected
TLMIN1 - 0 First legal Detector channel
DETCHANS - 1024 No. of legal detector channels
NCHAN - 1024 No. of detector channels in dataset
PHAVERSN - 1.1.0 OGIP FITS version number
STAT_ERR - FALSE Statistical Error
SYS_ERR - TRUE Fractional Systematic Error
QUALITY - TRUE Quality Flag
GROUPING - FALSE Grouping Flag
--------------------------------------------------------------------
--------------------------------------------------------------------
... QUALITY
...
... -------
... QUALITY
... -------
... Bad Channels (Channel - Channel)
... ---------------------------------------------
... 0 - 31 have quality 5
... ---------------------------------------------
...
...... exiting, changes written to file : spec0.tmp
Command not found; type ? for a command listing
!xsel:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!xsel:ASCA > set datadir .
Setting data directory to /data/data16/seq_proc/55000030.005/
Setting mkf directory to /data/data16/seq_proc/55000030.005/
!xsel:ASCA > read events events.tmp
Got new instrument: SIS0
Setting: IMAGE binning = 4
WMAP binning = 8
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 4095
Got the minimum time resolution of the read data: 16.000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data16/seq_proc/55000030.005/
HK Directory is: /data/data16/seq_proc/55000030.005/
!xsel:ASCA-SIS0-BRIGHT2 > set phaname PI
!xsel:ASCA-SIS0-BRIGHT2 > filter region ad55000030s032002_0.reg
!xsel:ASCA-SIS0-BRIGHT2 > filter region SIS0_OFFCHIP.1
!xsel:ASCA-SIS0-BRIGHT2 > filter region ad55000030s010212.discrim
!xsel:ASCA-SIS0-BRIGHT2 > filter region SIS0_NOTCHIP1.1
!xsel:ASCA-SIS0-BRIGHT2 > filter region SIS0_NOTCHIP2.1
!xsel:ASCA-SIS0-BRIGHT2 > filter region SIS0_NOTCHIP3.1
!xsel:ASCA-SIS0-BRIGHT2 > extract spectrum
!xsel:ASCA-SIS0-BRIGHT2 > save spectrum spec0.tmp group=yes
Wrote spectrum to spec0.tmp
!xsel:ASCA-SIS0-BRIGHT2 > exit save_session=no
-> sis0c0p40_290296.fits already present in current directorySisrmg Version 1.1, Configured 04/97 This version resolves *all* known keyword incompatibilities with other FTOOLS tasks. If you have previously fudged *any* keywords in the PHA file to compensate, incorrect results will follow. Setting 1st PHA channel to 0 Making v1.1 1180x1024 S0C0 Bright2 PI RMF Calibration data from ./ Please stand by... ...Done.-> SIS0_NOTCHIP0.1 already present in current directory
** XSELECT V1.3 **
!> Enter session name >[xsel] xsel
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS S0CCDPOW
1 GAL_RIDG BRIGHT2 HIGH 09/04/97 21:02:58 0.65E+04 1426 1111
EXTRACTOR vers 2.0 11 Apr 1997.
Getting FITS WCS Keywords
Doing file: /data/data16/seq_proc/55000030.005/events.tmp
Total Good Bad: Region Time Phase Cut
1426 407 1019 0 0 0
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
1426 407 1019 0 0 0
in 6489.46 seconds
Spectrum has 407 counts for 6.2717E-02 counts/sec
-------------------------
MANDATORY KEYWORDS/VALUES
-------------------------
--------------------------------------------------------------------
--------------------------------------------------------------------
EXTNAME - SPECTRUM Name of this BINTABLE
TELESCOP - ASCA Mission/Satellite name
INSTRUME - SIS0 Instrument/Detector
FILTER - Instrument filter in use
EXPOSURE - 6489.5 Integration time (in secs) of PHA data
AREASCAL - 1.0000 Area scaling factor
BACKSCAL - 0.15947 Background scaling factor
BACKFILE - NONE Associated background file
CORRSCAL - 1.0000 Correlation scaling factor
CORRFILE - none Associated correlation file
RESPFILE - NONE Associated redistribution matrix file
ANCRFILE - none Associated ancillary response file
XFLT0001 - none XSPEC selection filter
POISSERR - TRUE Whether Poissonian errors apply
CHANTYPE - PI Whether channels have been corrected
TLMIN1 - 0 First legal Detector channel
DETCHANS - 1024 No. of legal detector channels
NCHAN - 1024 No. of detector channels in dataset
PHAVERSN - 1.1.0 OGIP FITS version number
STAT_ERR - FALSE Statistical Error
SYS_ERR - TRUE Fractional Systematic Error
QUALITY - TRUE Quality Flag
GROUPING - FALSE Grouping Flag
--------------------------------------------------------------------
--------------------------------------------------------------------
... QUALITY
...
... -------
... QUALITY
... -------
... Bad Channels (Channel - Channel)
... ---------------------------------------------
... 0 - 31 have quality 5
... ---------------------------------------------
...
...... exiting, changes written to file : spec1.tmp
Command not found; type ? for a command listing
!xsel:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!xsel:ASCA > set datadir .
Setting data directory to /data/data16/seq_proc/55000030.005/
Setting mkf directory to /data/data16/seq_proc/55000030.005/
!xsel:ASCA > read events events.tmp
Got new instrument: SIS0
Setting: IMAGE binning = 4
WMAP binning = 8
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 4095
Got the minimum time resolution of the read data: 16.000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data16/seq_proc/55000030.005/
HK Directory is: /data/data16/seq_proc/55000030.005/
!xsel:ASCA-SIS0-BRIGHT2 > set phaname PI
!xsel:ASCA-SIS0-BRIGHT2 > filter region ad55000030s032002_0.reg
!xsel:ASCA-SIS0-BRIGHT2 > filter region SIS0_OFFCHIP.1
!xsel:ASCA-SIS0-BRIGHT2 > filter region ad55000030s010212.discrim
!xsel:ASCA-SIS0-BRIGHT2 > filter region SIS0_NOTCHIP0.1
!xsel:ASCA-SIS0-BRIGHT2 > filter region SIS0_NOTCHIP2.1
!xsel:ASCA-SIS0-BRIGHT2 > filter region SIS0_NOTCHIP3.1
!xsel:ASCA-SIS0-BRIGHT2 > extract spectrum
!xsel:ASCA-SIS0-BRIGHT2 > save spectrum spec1.tmp group=yes
Wrote spectrum to spec1.tmp
!xsel:ASCA-SIS0-BRIGHT2 > exit save_session=no
-> sis0c1p40_290296.fits already present in current directorySisrmg Version 1.1, Configured 04/97 This version resolves *all* known keyword incompatibilities with other FTOOLS tasks. If you have previously fudged *any* keywords in the PHA file to compensate, incorrect results will follow. Setting 1st PHA channel to 0 Making v1.1 1180x1024 S0C1 Bright2 PI RMF Calibration data from ./ Please stand by... ...Done.-> SIS0_NOTCHIP0.1 already present in current directory
** XSELECT V1.3 **
!> Enter session name >[xsel] xsel
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS S0CCDPOW
1 GAL_RIDG BRIGHT2 HIGH 09/04/97 21:02:58 0.65E+04 1426 1111
EXTRACTOR vers 2.0 11 Apr 1997.
Getting FITS WCS Keywords
Doing file: /data/data16/seq_proc/55000030.005/events.tmp
Total Good Bad: Region Time Phase Cut
1426 305 1121 0 0 0
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
1426 305 1121 0 0 0
in 6489.46 seconds
Spectrum has 305 counts for 4.6999E-02 counts/sec
-------------------------
MANDATORY KEYWORDS/VALUES
-------------------------
--------------------------------------------------------------------
--------------------------------------------------------------------
EXTNAME - SPECTRUM Name of this BINTABLE
TELESCOP - ASCA Mission/Satellite name
INSTRUME - SIS0 Instrument/Detector
FILTER - Instrument filter in use
EXPOSURE - 6489.5 Integration time (in secs) of PHA data
AREASCAL - 1.0000 Area scaling factor
BACKSCAL - 0.15997 Background scaling factor
BACKFILE - NONE Associated background file
CORRSCAL - 1.0000 Correlation scaling factor
CORRFILE - none Associated correlation file
RESPFILE - NONE Associated redistribution matrix file
ANCRFILE - none Associated ancillary response file
XFLT0001 - none XSPEC selection filter
POISSERR - TRUE Whether Poissonian errors apply
CHANTYPE - PI Whether channels have been corrected
TLMIN1 - 0 First legal Detector channel
DETCHANS - 1024 No. of legal detector channels
NCHAN - 1024 No. of detector channels in dataset
PHAVERSN - 1.1.0 OGIP FITS version number
STAT_ERR - FALSE Statistical Error
SYS_ERR - TRUE Fractional Systematic Error
QUALITY - TRUE Quality Flag
GROUPING - FALSE Grouping Flag
--------------------------------------------------------------------
--------------------------------------------------------------------
... QUALITY
...
... -------
... QUALITY
... -------
... Bad Channels (Channel - Channel)
... ---------------------------------------------
... 0 - 31 have quality 5
... ---------------------------------------------
...
...... exiting, changes written to file : spec2.tmp
Command not found; type ? for a command listing
!xsel:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!xsel:ASCA > set datadir .
Setting data directory to /data/data16/seq_proc/55000030.005/
Setting mkf directory to /data/data16/seq_proc/55000030.005/
!xsel:ASCA > read events events.tmp
Got new instrument: SIS0
Setting: IMAGE binning = 4
WMAP binning = 8
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 4095
Got the minimum time resolution of the read data: 16.000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data16/seq_proc/55000030.005/
HK Directory is: /data/data16/seq_proc/55000030.005/
!xsel:ASCA-SIS0-BRIGHT2 > set phaname PI
!xsel:ASCA-SIS0-BRIGHT2 > filter region ad55000030s032002_0.reg
!xsel:ASCA-SIS0-BRIGHT2 > filter region SIS0_OFFCHIP.1
!xsel:ASCA-SIS0-BRIGHT2 > filter region ad55000030s010212.discrim
!xsel:ASCA-SIS0-BRIGHT2 > filter region SIS0_NOTCHIP0.1
!xsel:ASCA-SIS0-BRIGHT2 > filter region SIS0_NOTCHIP1.1
!xsel:ASCA-SIS0-BRIGHT2 > filter region SIS0_NOTCHIP3.1
!xsel:ASCA-SIS0-BRIGHT2 > extract spectrum
!xsel:ASCA-SIS0-BRIGHT2 > save spectrum spec2.tmp group=yes
Wrote spectrum to spec2.tmp
!xsel:ASCA-SIS0-BRIGHT2 > exit save_session=no
-> sis0c2p40_290296.fits already present in current directorySisrmg Version 1.1, Configured 04/97 This version resolves *all* known keyword incompatibilities with other FTOOLS tasks. If you have previously fudged *any* keywords in the PHA file to compensate, incorrect results will follow. Setting 1st PHA channel to 0 Making v1.1 1180x1024 S0C2 Bright2 PI RMF Calibration data from ./ Please stand by... ...Done.-> SIS0_NOTCHIP0.1 already present in current directory
** XSELECT V1.3 **
!> Enter session name >[xsel] xsel
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS S0CCDPOW
1 GAL_RIDG BRIGHT2 HIGH 09/04/97 21:02:58 0.65E+04 1426 1111
EXTRACTOR vers 2.0 11 Apr 1997.
Getting FITS WCS Keywords
Doing file: /data/data16/seq_proc/55000030.005/events.tmp
Total Good Bad: Region Time Phase Cut
1426 366 1060 0 0 0
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
1426 366 1060 0 0 0
in 6489.46 seconds
Spectrum has 366 counts for 5.6399E-02 counts/sec
-------------------------
MANDATORY KEYWORDS/VALUES
-------------------------
--------------------------------------------------------------------
--------------------------------------------------------------------
EXTNAME - SPECTRUM Name of this BINTABLE
TELESCOP - ASCA Mission/Satellite name
INSTRUME - SIS0 Instrument/Detector
FILTER - Instrument filter in use
EXPOSURE - 6489.5 Integration time (in secs) of PHA data
AREASCAL - 1.0000 Area scaling factor
BACKSCAL - 0.15896 Background scaling factor
BACKFILE - NONE Associated background file
CORRSCAL - 1.0000 Correlation scaling factor
CORRFILE - none Associated correlation file
RESPFILE - NONE Associated redistribution matrix file
ANCRFILE - none Associated ancillary response file
XFLT0001 - none XSPEC selection filter
POISSERR - TRUE Whether Poissonian errors apply
CHANTYPE - PI Whether channels have been corrected
TLMIN1 - 0 First legal Detector channel
DETCHANS - 1024 No. of legal detector channels
NCHAN - 1024 No. of detector channels in dataset
PHAVERSN - 1.1.0 OGIP FITS version number
STAT_ERR - FALSE Statistical Error
SYS_ERR - TRUE Fractional Systematic Error
QUALITY - TRUE Quality Flag
GROUPING - FALSE Grouping Flag
--------------------------------------------------------------------
--------------------------------------------------------------------
... QUALITY
...
... -------
... QUALITY
... -------
... Bad Channels (Channel - Channel)
... ---------------------------------------------
... 0 - 31 have quality 5
... ---------------------------------------------
...
...... exiting, changes written to file : spec3.tmp
Command not found; type ? for a command listing
!xsel:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!xsel:ASCA > set datadir .
Setting data directory to /data/data16/seq_proc/55000030.005/
Setting mkf directory to /data/data16/seq_proc/55000030.005/
!xsel:ASCA > read events events.tmp
Got new instrument: SIS0
Setting: IMAGE binning = 4
WMAP binning = 8
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 4095
Got the minimum time resolution of the read data: 16.000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data16/seq_proc/55000030.005/
HK Directory is: /data/data16/seq_proc/55000030.005/
!xsel:ASCA-SIS0-BRIGHT2 > set phaname PI
!xsel:ASCA-SIS0-BRIGHT2 > filter region ad55000030s032002_0.reg
!xsel:ASCA-SIS0-BRIGHT2 > filter region SIS0_OFFCHIP.1
!xsel:ASCA-SIS0-BRIGHT2 > filter region ad55000030s010212.discrim
!xsel:ASCA-SIS0-BRIGHT2 > filter region SIS0_NOTCHIP0.1
!xsel:ASCA-SIS0-BRIGHT2 > filter region SIS0_NOTCHIP1.1
!xsel:ASCA-SIS0-BRIGHT2 > filter region SIS0_NOTCHIP2.1
!xsel:ASCA-SIS0-BRIGHT2 > extract spectrum
!xsel:ASCA-SIS0-BRIGHT2 > save spectrum spec3.tmp group=yes
Wrote spectrum to spec3.tmp
!xsel:ASCA-SIS0-BRIGHT2 > exit save_session=no
-> sis0c3p40_290296.fits already present in current directorySisrmg Version 1.1, Configured 04/97 This version resolves *all* known keyword incompatibilities with other FTOOLS tasks. If you have previously fudged *any* keywords in the PHA file to compensate, incorrect results will follow. Setting 1st PHA channel to 0 Making v1.1 1180x1024 S0C3 Bright2 PI RMF Calibration data from ./ Please stand by... ...Done.-> Chip weights:
rmf0.tmp 0.244039270687237 rmf1.tmp 0.285413744740533 rmf2.tmp 0.213884992987377 rmf3.tmp 0.256661991584853-> Standard Output From FTOOL addrmf:
ADDRMF vers 1.10 10 April, 1997.
Summing ...
2.440E-01 * rmf0.tmp
2.854E-01 * rmf1.tmp
2.139E-01 * rmf2.tmp
2.567E-01 * rmf3.tmp
RMF # 1 : rmf0.tmp 0.24
ASCA SIS0 NONE NONE PI
RMF # 2 : rmf1.tmp 0.29
ASCA SIS0 NONE NONE PI
RMF # 3 : rmf2.tmp 0.21
ASCA SIS0 NONE NONE PI
RMF # 4 : rmf3.tmp 0.26
ASCA SIS0 NONE NONE PI
-> Generating ad55000030s010212_0.arf with point=no
ASCAARF vers 2.72 14 Mar 1997.
Input WMAP array has size 106 by 134 bins
expanded to 106 by 134 bins
First WMAP bin is at detector pixel 224 208
8 detector pixels per WMAP bin
WMAP bin size is 0.21600 mm
0.21216 arcmin
Selected region size is 545.40 arcmin^2
Optical axis is detector pixel 662.72 559.02
1180 energies from RMF file
Effective area fudge applied
Arf filter applied
Total counts in region = 1.39200E+03
Weighted mean angle from optical axis = 8.614 arcmin
-> Standard Output From STOOL group_event_files:1 ad55000030s100102h.evt 841 1 ad55000030s100202h.evt 841 1 ad55000030s100302m.evt 841-> Fetching SIS1_OFFCHIP.1
ad55000030s100102h.evt ad55000030s100202h.evt ad55000030s100302m.evt-> Standard Output From FTOOL xselect:
** XSELECT V1.3 **
!> Enter session name >[xsel] xsel
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS S1CCDPOW
1 GAL_RIDG BRIGHT HIGH 09/04/97 21:02:58 0.70E+04 740 1111
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS S1CCDPOW
1 GAL_RIDG BRIGHT HIGH 09/04/97 21:02:58 0.70E+04 740 1111
2 GAL_RIDG BRIGHT HIGH 10/04/97 02:43:42 0.16E+02 44 1111
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS S1CCDPOW
1 GAL_RIDG BRIGHT HIGH 09/04/97 21:02:58 0.70E+04 740 1111
2 GAL_RIDG BRIGHT HIGH 10/04/97 02:43:42 0.16E+02 44 1111
3 GAL_RIDG BRIGHT MEDIUM 09/04/97 20:51:26 0.80E+02 57 1111
EXTRACTOR vers 2.0 11 Apr 1997.
Getting FITS WCS Keywords
Doing file: /data/data16/seq_proc/55000030.005/ad55000030s100102h.evt
Total Good Bad: Region Time Phase Cut
740 722 18 0 0 0
Doing file: /data/data16/seq_proc/55000030.005/ad55000030s100202h.evt
Total Good Bad: Region Time Phase Cut
44 40 4 0 0 0
Doing file: /data/data16/seq_proc/55000030.005/ad55000030s100302m.evt
Total Good Bad: Region Time Phase Cut
57 55 2 0 0 0
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
841 817 24 0 0 0
in 7103.77 seconds
Spectrum has 817 counts for 0.1150 counts/sec
-------------------------
MANDATORY KEYWORDS/VALUES
-------------------------
--------------------------------------------------------------------
--------------------------------------------------------------------
EXTNAME - SPECTRUM Name of this BINTABLE
TELESCOP - ASCA Mission/Satellite name
INSTRUME - SIS1 Instrument/Detector
FILTER - Instrument filter in use
EXPOSURE - 7103.8 Integration time (in secs) of PHA data
AREASCAL - 1.0000 Area scaling factor
BACKSCAL - 0.47152 Background scaling factor
BACKFILE - NONE Associated background file
CORRSCAL - 1.0000 Correlation scaling factor
CORRFILE - none Associated correlation file
RESPFILE - NONE Associated redistribution matrix file
ANCRFILE - none Associated ancillary response file
XFLT0001 - none XSPEC selection filter
POISSERR - TRUE Whether Poissonian errors apply
CHANTYPE - PI Whether channels have been corrected
TLMIN1 - 0 First legal Detector channel
DETCHANS - 512 No. of legal detector channels
NCHAN - 512 No. of detector channels in dataset
PHAVERSN - 1.1.0 OGIP FITS version number
STAT_ERR - FALSE Statistical Error
SYS_ERR - TRUE Fractional Systematic Error
QUALITY - TRUE Quality Flag
GROUPING - FALSE Grouping Flag
--------------------------------------------------------------------
--------------------------------------------------------------------
... QUALITY
...
... -------
... QUALITY
... -------
... Bad Channels (Channel - Channel)
... ---------------------------------------------
... 0 - 15 have quality 5
... ---------------------------------------------
...
...... exiting, changes written to file : ad55000030s110102_0.pi
EXTRACTOR vers 2.0 11 Apr 1997.
Doing file: /data/data16/seq_proc/55000030.005/ad55000030s100102h.evt
Total Good Bad: Region Time Phase Cut
740 722 18 0 0 0
Writing events file
722 events written to the output file
Doing file: /data/data16/seq_proc/55000030.005/ad55000030s100202h.evt
Total Good Bad: Region Time Phase Cut
44 40 4 0 0 0
Writing events file
762 events written to the output file
Doing file: /data/data16/seq_proc/55000030.005/ad55000030s100302m.evt
Total Good Bad: Region Time Phase Cut
57 55 2 0 0 0
Writing events file
817 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
841 817 24 0 0 0
in 7103.77 seconds
Command not found; type ? for a command listing
!xsel:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!xsel:ASCA > set datadir .
Setting data directory to /data/data16/seq_proc/55000030.005/
Setting mkf directory to /data/data16/seq_proc/55000030.005/
!xsel:ASCA > read events ad55000030s100102h.evt
Got new instrument: SIS1
Setting: IMAGE binning = 4
WMAP binning = 8
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 2047
Got the minimum time resolution of the read data: 16.000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data16/seq_proc/55000030.005/
HK Directory is: /data/data16/seq_proc/55000030.005/
!xsel:ASCA-SIS1-BRIGHT > read events ad55000030s100202h.evt
Getting Min and Max for Energy Column...
Got min and max for PI: 0 2047
Got the minimum time resolution of the read data: 16.000
Number of files read in: 2
******************** Observation Catalogue ********************
Data Directory is: /data/data16/seq_proc/55000030.005/
HK Directory is: /data/data16/seq_proc/55000030.005/
!xsel:ASCA-SIS1-BRIGHT > read events ad55000030s100302m.evt
Getting Min and Max for Energy Column...
Got min and max for PI: 0 2047
Got the minimum time resolution of the read data: 16.000
Number of files read in: 3
******************** Observation Catalogue ********************
Data Directory is: /data/data16/seq_proc/55000030.005/
HK Directory is: /data/data16/seq_proc/55000030.005/
!xsel:ASCA-SIS1-BRIGHT > set phaname PI
!xsel:ASCA-SIS1-BRIGHT > filter region ad55000030s132002_0.reg
!xsel:ASCA-SIS1-BRIGHT > filter region SIS1_OFFCHIP.1
!xsel:ASCA-SIS1-BRIGHT > filter region ad55000030s110102.discrim
!xsel:ASCA-SIS1-BRIGHT > extract spectrum
!xsel:ASCA-SIS1-BRIGHT > save spectrum ad55000030s110102_0.pi group=yes
Wrote spectrum to ad55000030s110102_0.pi
!xsel:ASCA-SIS1-BRIGHT > extract events
!xsel:ASCA-SIS1-BRIGHT > save events outfile=events.tmp use_events=yes
Wrote events list to file events.tmp
Changing Data directory from:
/data/data16/seq_proc/55000030.005/
to the current working directory.
!xsel:ASCA-SIS1-BRIGHT > exit save_session=no
-> Grouping ad55000030s110102_0.pi to 40 counts/bin------------------------- MANDATORY KEYWORDS/VALUES ------------------------- -------------------------------------------------------------------- -------------------------------------------------------------------- EXTNAME - SPECTRUM Name of this BINTABLE TELESCOP - ASCA Mission/Satellite name INSTRUME - SIS1 Instrument/Detector FILTER - Instrument filter in use EXPOSURE - 7103.8 Integration time (in secs) of PHA data AREASCAL - 1.0000 Area scaling factor BACKSCAL - 0.47152 Background scaling factor BACKFILE - NONE Associated background file CORRSCAL - 1.0000 Correlation scaling factor CORRFILE - none Associated correlation file RESPFILE - NONE Associated redistribution matrix file ANCRFILE - none Associated ancillary response file XFLT0001 - none XSPEC selection filter POISSERR - TRUE Whether Poissonian errors apply CHANTYPE - PI Whether channels have been corrected TLMIN1 - 0 First legal Detector channel DETCHANS - 512 No. of legal detector channels NCHAN - 512 No. of detector channels in dataset PHAVERSN - 1.1.0 OGIP FITS version number STAT_ERR - FALSE Statistical Error SYS_ERR - TRUE Fractional Systematic Error QUALITY - TRUE Quality Flag GROUPING - FALSE Grouping Flag -------------------------------------------------------------------- -------------------------------------------------------------------- ... ... -------- ... GROUPING ... -------- ... --------------------------------------------- ... Channel Grouping (Channel-Channel) : ... 0 - 15 of undefined grouping (Channel quality=bad) ... 16 - 41 are grouped by a factor 26 ... 42 - 45 are grouped by a factor 4 ... 46 - 48 are grouped by a factor 3 ... 49 - 52 are grouped by a factor 4 ... 53 - 55 are grouped by a factor 3 ... 56 - 67 are grouped by a factor 4 ... 68 - 73 are grouped by a factor 6 ... 74 - 89 are grouped by a factor 8 ... 90 - 98 are grouped by a factor 9 ... 99 - 109 are grouped by a factor 11 ... 110 - 123 are grouped by a factor 14 ... 124 - 141 are grouped by a factor 18 ... 142 - 166 are grouped by a factor 25 ... 167 - 207 are grouped by a factor 41 ... 208 - 266 are grouped by a factor 59 ... 267 - 511 of undefined grouping (Channel quality=bad) ... --------------------------------------------- ... ...... exiting, changes written to file : ad55000030s110102_0.pi ** grppha 2.6.0 completed successfully-> Source occupies chip(s) 0 1 2 3
** XSELECT V1.3 **
!> Enter session name >[xsel] xsel
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS S1CCDPOW
1 GAL_RIDG BRIGHT HIGH 09/04/97 20:51:26 0.71E+04 817 1111
EXTRACTOR vers 2.0 11 Apr 1997.
Getting FITS WCS Keywords
Doing file: /data/data16/seq_proc/55000030.005/events.tmp
Total Good Bad: Region Time Phase Cut
817 144 673 0 0 0
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
817 144 673 0 0 0
in 7103.77 seconds
Spectrum has 144 counts for 2.0271E-02 counts/sec
-------------------------
MANDATORY KEYWORDS/VALUES
-------------------------
--------------------------------------------------------------------
--------------------------------------------------------------------
EXTNAME - SPECTRUM Name of this BINTABLE
TELESCOP - ASCA Mission/Satellite name
INSTRUME - SIS1 Instrument/Detector
FILTER - Instrument filter in use
EXPOSURE - 7103.8 Integration time (in secs) of PHA data
AREASCAL - 1.0000 Area scaling factor
BACKSCAL - 0.15818 Background scaling factor
BACKFILE - NONE Associated background file
CORRSCAL - 1.0000 Correlation scaling factor
CORRFILE - none Associated correlation file
RESPFILE - NONE Associated redistribution matrix file
ANCRFILE - none Associated ancillary response file
XFLT0001 - none XSPEC selection filter
POISSERR - TRUE Whether Poissonian errors apply
CHANTYPE - PI Whether channels have been corrected
TLMIN1 - 0 First legal Detector channel
DETCHANS - 512 No. of legal detector channels
NCHAN - 512 No. of detector channels in dataset
PHAVERSN - 1.1.0 OGIP FITS version number
STAT_ERR - FALSE Statistical Error
SYS_ERR - TRUE Fractional Systematic Error
QUALITY - TRUE Quality Flag
GROUPING - FALSE Grouping Flag
--------------------------------------------------------------------
--------------------------------------------------------------------
... QUALITY
...
... -------
... QUALITY
... -------
... Bad Channels (Channel - Channel)
... ---------------------------------------------
... 0 - 15 have quality 5
... ---------------------------------------------
...
...... exiting, changes written to file : spec0.tmp
Command not found; type ? for a command listing
!xsel:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!xsel:ASCA > set datadir .
Setting data directory to /data/data16/seq_proc/55000030.005/
Setting mkf directory to /data/data16/seq_proc/55000030.005/
!xsel:ASCA > read events events.tmp
Got new instrument: SIS1
Setting: IMAGE binning = 4
WMAP binning = 8
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 2047
Got the minimum time resolution of the read data: 16.000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data16/seq_proc/55000030.005/
HK Directory is: /data/data16/seq_proc/55000030.005/
!xsel:ASCA-SIS1-BRIGHT > set phaname PI
!xsel:ASCA-SIS1-BRIGHT > filter region ad55000030s132002_0.reg
!xsel:ASCA-SIS1-BRIGHT > filter region SIS1_OFFCHIP.1
!xsel:ASCA-SIS1-BRIGHT > filter region ad55000030s110102.discrim
!xsel:ASCA-SIS1-BRIGHT > filter region SIS1_NOTCHIP1.1
!xsel:ASCA-SIS1-BRIGHT > filter region SIS1_NOTCHIP2.1
!xsel:ASCA-SIS1-BRIGHT > filter region SIS1_NOTCHIP3.1
!xsel:ASCA-SIS1-BRIGHT > extract spectrum
!xsel:ASCA-SIS1-BRIGHT > save spectrum spec0.tmp group=yes
Wrote spectrum to spec0.tmp
!xsel:ASCA-SIS1-BRIGHT > exit save_session=no
-> Fetching sis1c0p40_290296.fitsSisrmg Version 1.1, Configured 04/97 This version resolves *all* known keyword incompatibilities with other FTOOLS tasks. If you have previously fudged *any* keywords in the PHA file to compensate, incorrect results will follow. Setting 1st PHA channel to 0 Making v1.1 1180x512 S1C0 Bright PI RMF Calibration data from ./ Please stand by... ...Done.-> Fetching SIS1_NOTCHIP0.1
** XSELECT V1.3 **
!> Enter session name >[xsel] xsel
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS S1CCDPOW
1 GAL_RIDG BRIGHT HIGH 09/04/97 20:51:26 0.71E+04 817 1111
EXTRACTOR vers 2.0 11 Apr 1997.
Getting FITS WCS Keywords
Doing file: /data/data16/seq_proc/55000030.005/events.tmp
Total Good Bad: Region Time Phase Cut
817 277 540 0 0 0
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
817 277 540 0 0 0
in 7103.77 seconds
Spectrum has 277 counts for 3.8993E-02 counts/sec
-------------------------
MANDATORY KEYWORDS/VALUES
-------------------------
--------------------------------------------------------------------
--------------------------------------------------------------------
EXTNAME - SPECTRUM Name of this BINTABLE
TELESCOP - ASCA Mission/Satellite name
INSTRUME - SIS1 Instrument/Detector
FILTER - Instrument filter in use
EXPOSURE - 7103.8 Integration time (in secs) of PHA data
AREASCAL - 1.0000 Area scaling factor
BACKSCAL - 0.15767 Background scaling factor
BACKFILE - NONE Associated background file
CORRSCAL - 1.0000 Correlation scaling factor
CORRFILE - none Associated correlation file
RESPFILE - NONE Associated redistribution matrix file
ANCRFILE - none Associated ancillary response file
XFLT0001 - none XSPEC selection filter
POISSERR - TRUE Whether Poissonian errors apply
CHANTYPE - PI Whether channels have been corrected
TLMIN1 - 0 First legal Detector channel
DETCHANS - 512 No. of legal detector channels
NCHAN - 512 No. of detector channels in dataset
PHAVERSN - 1.1.0 OGIP FITS version number
STAT_ERR - FALSE Statistical Error
SYS_ERR - TRUE Fractional Systematic Error
QUALITY - TRUE Quality Flag
GROUPING - FALSE Grouping Flag
--------------------------------------------------------------------
--------------------------------------------------------------------
... QUALITY
...
... -------
... QUALITY
... -------
... Bad Channels (Channel - Channel)
... ---------------------------------------------
... 0 - 15 have quality 5
... ---------------------------------------------
...
...... exiting, changes written to file : spec1.tmp
Command not found; type ? for a command listing
!xsel:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!xsel:ASCA > set datadir .
Setting data directory to /data/data16/seq_proc/55000030.005/
Setting mkf directory to /data/data16/seq_proc/55000030.005/
!xsel:ASCA > read events events.tmp
Got new instrument: SIS1
Setting: IMAGE binning = 4
WMAP binning = 8
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 2047
Got the minimum time resolution of the read data: 16.000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data16/seq_proc/55000030.005/
HK Directory is: /data/data16/seq_proc/55000030.005/
!xsel:ASCA-SIS1-BRIGHT > set phaname PI
!xsel:ASCA-SIS1-BRIGHT > filter region ad55000030s132002_0.reg
!xsel:ASCA-SIS1-BRIGHT > filter region SIS1_OFFCHIP.1
!xsel:ASCA-SIS1-BRIGHT > filter region ad55000030s110102.discrim
!xsel:ASCA-SIS1-BRIGHT > filter region SIS1_NOTCHIP0.1
!xsel:ASCA-SIS1-BRIGHT > filter region SIS1_NOTCHIP2.1
!xsel:ASCA-SIS1-BRIGHT > filter region SIS1_NOTCHIP3.1
!xsel:ASCA-SIS1-BRIGHT > extract spectrum
!xsel:ASCA-SIS1-BRIGHT > save spectrum spec1.tmp group=yes
Wrote spectrum to spec1.tmp
!xsel:ASCA-SIS1-BRIGHT > exit save_session=no
-> Fetching sis1c1p40_290296.fitsSisrmg Version 1.1, Configured 04/97 This version resolves *all* known keyword incompatibilities with other FTOOLS tasks. If you have previously fudged *any* keywords in the PHA file to compensate, incorrect results will follow. Setting 1st PHA channel to 0 Making v1.1 1180x512 S1C1 Bright PI RMF Calibration data from ./ Please stand by... ...Done.-> SIS1_NOTCHIP0.1 already present in current directory
** XSELECT V1.3 **
!> Enter session name >[xsel] xsel
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS S1CCDPOW
1 GAL_RIDG BRIGHT HIGH 09/04/97 20:51:26 0.71E+04 817 1111
EXTRACTOR vers 2.0 11 Apr 1997.
Getting FITS WCS Keywords
Doing file: /data/data16/seq_proc/55000030.005/events.tmp
Total Good Bad: Region Time Phase Cut
817 272 545 0 0 0
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
817 272 545 0 0 0
in 7103.77 seconds
Spectrum has 272 counts for 3.8290E-02 counts/sec
-------------------------
MANDATORY KEYWORDS/VALUES
-------------------------
--------------------------------------------------------------------
--------------------------------------------------------------------
EXTNAME - SPECTRUM Name of this BINTABLE
TELESCOP - ASCA Mission/Satellite name
INSTRUME - SIS1 Instrument/Detector
FILTER - Instrument filter in use
EXPOSURE - 7103.8 Integration time (in secs) of PHA data
AREASCAL - 1.0000 Area scaling factor
BACKSCAL - 0.15818 Background scaling factor
BACKFILE - NONE Associated background file
CORRSCAL - 1.0000 Correlation scaling factor
CORRFILE - none Associated correlation file
RESPFILE - NONE Associated redistribution matrix file
ANCRFILE - none Associated ancillary response file
XFLT0001 - none XSPEC selection filter
POISSERR - TRUE Whether Poissonian errors apply
CHANTYPE - PI Whether channels have been corrected
TLMIN1 - 0 First legal Detector channel
DETCHANS - 512 No. of legal detector channels
NCHAN - 512 No. of detector channels in dataset
PHAVERSN - 1.1.0 OGIP FITS version number
STAT_ERR - FALSE Statistical Error
SYS_ERR - TRUE Fractional Systematic Error
QUALITY - TRUE Quality Flag
GROUPING - FALSE Grouping Flag
--------------------------------------------------------------------
--------------------------------------------------------------------
... QUALITY
...
... -------
... QUALITY
... -------
... Bad Channels (Channel - Channel)
... ---------------------------------------------
... 0 - 15 have quality 5
... ---------------------------------------------
...
...... exiting, changes written to file : spec2.tmp
Command not found; type ? for a command listing
!xsel:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!xsel:ASCA > set datadir .
Setting data directory to /data/data16/seq_proc/55000030.005/
Setting mkf directory to /data/data16/seq_proc/55000030.005/
!xsel:ASCA > read events events.tmp
Got new instrument: SIS1
Setting: IMAGE binning = 4
WMAP binning = 8
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 2047
Got the minimum time resolution of the read data: 16.000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data16/seq_proc/55000030.005/
HK Directory is: /data/data16/seq_proc/55000030.005/
!xsel:ASCA-SIS1-BRIGHT > set phaname PI
!xsel:ASCA-SIS1-BRIGHT > filter region ad55000030s132002_0.reg
!xsel:ASCA-SIS1-BRIGHT > filter region SIS1_OFFCHIP.1
!xsel:ASCA-SIS1-BRIGHT > filter region ad55000030s110102.discrim
!xsel:ASCA-SIS1-BRIGHT > filter region SIS1_NOTCHIP0.1
!xsel:ASCA-SIS1-BRIGHT > filter region SIS1_NOTCHIP1.1
!xsel:ASCA-SIS1-BRIGHT > filter region SIS1_NOTCHIP3.1
!xsel:ASCA-SIS1-BRIGHT > extract spectrum
!xsel:ASCA-SIS1-BRIGHT > save spectrum spec2.tmp group=yes
Wrote spectrum to spec2.tmp
!xsel:ASCA-SIS1-BRIGHT > exit save_session=no
-> Fetching sis1c2p40_290296.fitsSisrmg Version 1.1, Configured 04/97 This version resolves *all* known keyword incompatibilities with other FTOOLS tasks. If you have previously fudged *any* keywords in the PHA file to compensate, incorrect results will follow. Setting 1st PHA channel to 0 Making v1.1 1180x512 S1C2 Bright PI RMF Calibration data from ./ Please stand by... ...Done.-> SIS1_NOTCHIP0.1 already present in current directory
** XSELECT V1.3 **
!> Enter session name >[xsel] xsel
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS S1CCDPOW
1 GAL_RIDG BRIGHT HIGH 09/04/97 20:51:26 0.71E+04 817 1111
EXTRACTOR vers 2.0 11 Apr 1997.
Getting FITS WCS Keywords
Doing file: /data/data16/seq_proc/55000030.005/events.tmp
Total Good Bad: Region Time Phase Cut
817 124 693 0 0 0
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
817 124 693 0 0 0
in 7103.77 seconds
Spectrum has 124 counts for 1.7456E-02 counts/sec
-------------------------
MANDATORY KEYWORDS/VALUES
-------------------------
--------------------------------------------------------------------
--------------------------------------------------------------------
EXTNAME - SPECTRUM Name of this BINTABLE
TELESCOP - ASCA Mission/Satellite name
INSTRUME - SIS1 Instrument/Detector
FILTER - Instrument filter in use
EXPOSURE - 7103.8 Integration time (in secs) of PHA data
AREASCAL - 1.0000 Area scaling factor
BACKSCAL - 0.15818 Background scaling factor
BACKFILE - NONE Associated background file
CORRSCAL - 1.0000 Correlation scaling factor
CORRFILE - none Associated correlation file
RESPFILE - NONE Associated redistribution matrix file
ANCRFILE - none Associated ancillary response file
XFLT0001 - none XSPEC selection filter
POISSERR - TRUE Whether Poissonian errors apply
CHANTYPE - PI Whether channels have been corrected
TLMIN1 - 0 First legal Detector channel
DETCHANS - 512 No. of legal detector channels
NCHAN - 512 No. of detector channels in dataset
PHAVERSN - 1.1.0 OGIP FITS version number
STAT_ERR - FALSE Statistical Error
SYS_ERR - TRUE Fractional Systematic Error
QUALITY - TRUE Quality Flag
GROUPING - FALSE Grouping Flag
--------------------------------------------------------------------
--------------------------------------------------------------------
... QUALITY
...
... -------
... QUALITY
... -------
... Bad Channels (Channel - Channel)
... ---------------------------------------------
... 0 - 15 have quality 5
... ---------------------------------------------
...
...... exiting, changes written to file : spec3.tmp
Command not found; type ? for a command listing
!xsel:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!xsel:ASCA > set datadir .
Setting data directory to /data/data16/seq_proc/55000030.005/
Setting mkf directory to /data/data16/seq_proc/55000030.005/
!xsel:ASCA > read events events.tmp
Got new instrument: SIS1
Setting: IMAGE binning = 4
WMAP binning = 8
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 2047
Got the minimum time resolution of the read data: 16.000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data16/seq_proc/55000030.005/
HK Directory is: /data/data16/seq_proc/55000030.005/
!xsel:ASCA-SIS1-BRIGHT > set phaname PI
!xsel:ASCA-SIS1-BRIGHT > filter region ad55000030s132002_0.reg
!xsel:ASCA-SIS1-BRIGHT > filter region SIS1_OFFCHIP.1
!xsel:ASCA-SIS1-BRIGHT > filter region ad55000030s110102.discrim
!xsel:ASCA-SIS1-BRIGHT > filter region SIS1_NOTCHIP0.1
!xsel:ASCA-SIS1-BRIGHT > filter region SIS1_NOTCHIP1.1
!xsel:ASCA-SIS1-BRIGHT > filter region SIS1_NOTCHIP2.1
!xsel:ASCA-SIS1-BRIGHT > extract spectrum
!xsel:ASCA-SIS1-BRIGHT > save spectrum spec3.tmp group=yes
Wrote spectrum to spec3.tmp
!xsel:ASCA-SIS1-BRIGHT > exit save_session=no
-> Fetching sis1c3p40_290296.fitsSisrmg Version 1.1, Configured 04/97 This version resolves *all* known keyword incompatibilities with other FTOOLS tasks. If you have previously fudged *any* keywords in the PHA file to compensate, incorrect results will follow. Setting 1st PHA channel to 0 Making v1.1 1180x512 S1C3 Bright PI RMF Calibration data from ./ Please stand by... ...Done.-> Chip weights:
rmf0.tmp 0.17625458996328 rmf1.tmp 0.339045287637699 rmf2.tmp 0.332925336597307 rmf3.tmp 0.151774785801714-> Standard Output From FTOOL addrmf:
ADDRMF vers 1.10 10 April, 1997.
Summing ...
1.763E-01 * rmf0.tmp
3.390E-01 * rmf1.tmp
3.329E-01 * rmf2.tmp
1.518E-01 * rmf3.tmp
RMF # 1 : rmf0.tmp 0.18
ASCA SIS1 NONE NONE PI
RMF # 2 : rmf1.tmp 0.34
ASCA SIS1 NONE NONE PI
RMF # 3 : rmf2.tmp 0.33
ASCA SIS1 NONE NONE PI
RMF # 4 : rmf3.tmp 0.15
ASCA SIS1 NONE NONE PI
-> Generating ad55000030s110102_0.arf with point=no
ASCAARF vers 2.72 14 Mar 1997.
Input WMAP array has size 106 by 134 bins
expanded to 106 by 134 bins
First WMAP bin is at detector pixel 224 208
8 detector pixels per WMAP bin
WMAP bin size is 0.21600 mm
0.21216 arcmin
Selected region size is 543.34 arcmin^2
Optical axis is detector pixel 618.28 773.83
1180 energies from RMF file
Effective area fudge applied
Arf filter applied
Total counts in region = 7.93000E+02
Weighted mean angle from optical axis = 8.490 arcmin
-> Standard Output From STOOL group_event_files:1 ad55000030s100112h.evt 1504 1 ad55000030s100212h.evt 1504-> SIS1_OFFCHIP.1 already present in current directory
ad55000030s100112h.evt ad55000030s100212h.evt-> Standard Output From FTOOL xselect:
** XSELECT V1.3 **
!> Enter session name >[xsel] xsel
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS S1CCDPOW
1 GAL_RIDG BRIGHT2 HIGH 09/04/97 21:02:58 0.70E+04 1395 1111
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS S1CCDPOW
1 GAL_RIDG BRIGHT2 HIGH 09/04/97 21:02:58 0.70E+04 1395 1111
2 GAL_RIDG BRIGHT2 HIGH 10/04/97 02:43:42 0.16E+02 109 1111
EXTRACTOR vers 2.0 11 Apr 1997.
Getting FITS WCS Keywords
Doing file: /data/data16/seq_proc/55000030.005/ad55000030s100112h.evt
Total Good Bad: Region Time Phase Cut
1395 1363 32 0 0 0
Doing file: /data/data16/seq_proc/55000030.005/ad55000030s100212h.evt
Total Good Bad: Region Time Phase Cut
109 104 5 0 0 0
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
1504 1467 37 0 0 0
in 7023.77 seconds
Spectrum has 1467 counts for 0.2089 counts/sec
-------------------------
MANDATORY KEYWORDS/VALUES
-------------------------
--------------------------------------------------------------------
--------------------------------------------------------------------
EXTNAME - SPECTRUM Name of this BINTABLE
TELESCOP - ASCA Mission/Satellite name
INSTRUME - SIS1 Instrument/Detector
FILTER - Instrument filter in use
EXPOSURE - 7023.8 Integration time (in secs) of PHA data
AREASCAL - 1.0000 Area scaling factor
BACKSCAL - 0.47152 Background scaling factor
BACKFILE - NONE Associated background file
CORRSCAL - 1.0000 Correlation scaling factor
CORRFILE - none Associated correlation file
RESPFILE - NONE Associated redistribution matrix file
ANCRFILE - none Associated ancillary response file
XFLT0001 - none XSPEC selection filter
POISSERR - TRUE Whether Poissonian errors apply
CHANTYPE - PI Whether channels have been corrected
TLMIN1 - 0 First legal Detector channel
DETCHANS - 1024 No. of legal detector channels
NCHAN - 1024 No. of detector channels in dataset
PHAVERSN - 1.1.0 OGIP FITS version number
STAT_ERR - FALSE Statistical Error
SYS_ERR - TRUE Fractional Systematic Error
QUALITY - TRUE Quality Flag
GROUPING - FALSE Grouping Flag
--------------------------------------------------------------------
--------------------------------------------------------------------
... QUALITY
...
... -------
... QUALITY
... -------
... Bad Channels (Channel - Channel)
... ---------------------------------------------
... 0 - 32 have quality 5
... ---------------------------------------------
...
...... exiting, changes written to file : ad55000030s110212_0.pi
EXTRACTOR vers 2.0 11 Apr 1997.
Doing file: /data/data16/seq_proc/55000030.005/ad55000030s100112h.evt
Total Good Bad: Region Time Phase Cut
1395 1363 32 0 0 0
Writing events file
1363 events written to the output file
Doing file: /data/data16/seq_proc/55000030.005/ad55000030s100212h.evt
Total Good Bad: Region Time Phase Cut
109 104 5 0 0 0
Writing events file
1467 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
1504 1467 37 0 0 0
in 7023.77 seconds
Command not found; type ? for a command listing
!xsel:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!xsel:ASCA > set datadir .
Setting data directory to /data/data16/seq_proc/55000030.005/
Setting mkf directory to /data/data16/seq_proc/55000030.005/
!xsel:ASCA > read events ad55000030s100112h.evt
Got new instrument: SIS1
Setting: IMAGE binning = 4
WMAP binning = 8
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 4095
Got the minimum time resolution of the read data: 16.000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data16/seq_proc/55000030.005/
HK Directory is: /data/data16/seq_proc/55000030.005/
!xsel:ASCA-SIS1-BRIGHT2 > read events ad55000030s100212h.evt
Getting Min and Max for Energy Column...
Got min and max for PI: 0 4095
Got the minimum time resolution of the read data: 16.000
Number of files read in: 2
******************** Observation Catalogue ********************
Data Directory is: /data/data16/seq_proc/55000030.005/
HK Directory is: /data/data16/seq_proc/55000030.005/
!xsel:ASCA-SIS1-BRIGHT2 > set phaname PI
!xsel:ASCA-SIS1-BRIGHT2 > filter region ad55000030s132002_0.reg
!xsel:ASCA-SIS1-BRIGHT2 > filter region SIS1_OFFCHIP.1
!xsel:ASCA-SIS1-BRIGHT2 > filter region ad55000030s110212.discrim
!xsel:ASCA-SIS1-BRIGHT2 > extract spectrum
!xsel:ASCA-SIS1-BRIGHT2 > save spectrum ad55000030s110212_0.pi group=yes
Wrote spectrum to ad55000030s110212_0.pi
!xsel:ASCA-SIS1-BRIGHT2 > extract events
!xsel:ASCA-SIS1-BRIGHT2 > save events outfile=events.tmp use_events=yes
Wrote events list to file events.tmp
Changing Data directory from:
/data/data16/seq_proc/55000030.005/
to the current working directory.
!xsel:ASCA-SIS1-BRIGHT2 > exit save_session=no
-> Grouping ad55000030s110212_0.pi to 40 counts/bin------------------------- MANDATORY KEYWORDS/VALUES ------------------------- -------------------------------------------------------------------- -------------------------------------------------------------------- EXTNAME - SPECTRUM Name of this BINTABLE TELESCOP - ASCA Mission/Satellite name INSTRUME - SIS1 Instrument/Detector FILTER - Instrument filter in use EXPOSURE - 7023.8 Integration time (in secs) of PHA data AREASCAL - 1.0000 Area scaling factor BACKSCAL - 0.47152 Background scaling factor BACKFILE - NONE Associated background file CORRSCAL - 1.0000 Correlation scaling factor CORRFILE - none Associated correlation file RESPFILE - NONE Associated redistribution matrix file ANCRFILE - none Associated ancillary response file XFLT0001 - none XSPEC selection filter POISSERR - TRUE Whether Poissonian errors apply CHANTYPE - PI Whether channels have been corrected TLMIN1 - 0 First legal Detector channel DETCHANS - 1024 No. of legal detector channels NCHAN - 1024 No. of detector channels in dataset PHAVERSN - 1.1.0 OGIP FITS version number STAT_ERR - FALSE Statistical Error SYS_ERR - TRUE Fractional Systematic Error QUALITY - TRUE Quality Flag GROUPING - FALSE Grouping Flag -------------------------------------------------------------------- -------------------------------------------------------------------- ... ... -------- ... GROUPING ... -------- ... --------------------------------------------- ... Channel Grouping (Channel-Channel) : ... 0 - 32 of undefined grouping (Channel quality=bad) ... 33 - 74 are grouped by a factor 42 ... 75 - 80 are grouped by a factor 6 ... 81 - 85 are grouped by a factor 5 ... 86 - 97 are grouped by a factor 4 ... 98 - 102 are grouped by a factor 5 ... 103 - 105 are grouped by a factor 3 ... 106 - 125 are grouped by a factor 5 ... 126 - 132 are grouped by a factor 7 ... 133 - 137 are grouped by a factor 5 ... 138 - 161 are grouped by a factor 8 ... 162 - 171 are grouped by a factor 10 ... 172 - 183 are grouped by a factor 12 ... 184 - 194 are grouped by a factor 11 ... 195 - 208 are grouped by a factor 14 ... 209 - 220 are grouped by a factor 12 ... 221 - 234 are grouped by a factor 14 ... 235 - 285 are grouped by a factor 17 ... 286 - 308 are grouped by a factor 23 ... 309 - 328 are grouped by a factor 20 ... 329 - 365 are grouped by a factor 37 ... 366 - 421 are grouped by a factor 56 ... 422 - 467 are grouped by a factor 46 ... 468 - 557 are grouped by a factor 90 ... --------------------------------------------- ... ...... exiting, changes written to file : ad55000030s110212_0.pi ** grppha 2.6.0 completed successfully-> Source occupies chip(s) 0 1 2 3
** XSELECT V1.3 **
!> Enter session name >[xsel] xsel
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS S1CCDPOW
1 GAL_RIDG BRIGHT2 HIGH 09/04/97 21:02:58 0.70E+04 1467 1111
EXTRACTOR vers 2.0 11 Apr 1997.
Getting FITS WCS Keywords
Doing file: /data/data16/seq_proc/55000030.005/events.tmp
Total Good Bad: Region Time Phase Cut
1467 283 1184 0 0 0
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
1467 283 1184 0 0 0
in 7023.77 seconds
Spectrum has 283 counts for 4.0292E-02 counts/sec
-------------------------
MANDATORY KEYWORDS/VALUES
-------------------------
--------------------------------------------------------------------
--------------------------------------------------------------------
EXTNAME - SPECTRUM Name of this BINTABLE
TELESCOP - ASCA Mission/Satellite name
INSTRUME - SIS1 Instrument/Detector
FILTER - Instrument filter in use
EXPOSURE - 7023.8 Integration time (in secs) of PHA data
AREASCAL - 1.0000 Area scaling factor
BACKSCAL - 0.15818 Background scaling factor
BACKFILE - NONE Associated background file
CORRSCAL - 1.0000 Correlation scaling factor
CORRFILE - none Associated correlation file
RESPFILE - NONE Associated redistribution matrix file
ANCRFILE - none Associated ancillary response file
XFLT0001 - none XSPEC selection filter
POISSERR - TRUE Whether Poissonian errors apply
CHANTYPE - PI Whether channels have been corrected
TLMIN1 - 0 First legal Detector channel
DETCHANS - 1024 No. of legal detector channels
NCHAN - 1024 No. of detector channels in dataset
PHAVERSN - 1.1.0 OGIP FITS version number
STAT_ERR - FALSE Statistical Error
SYS_ERR - TRUE Fractional Systematic Error
QUALITY - TRUE Quality Flag
GROUPING - FALSE Grouping Flag
--------------------------------------------------------------------
--------------------------------------------------------------------
... QUALITY
...
... -------
... QUALITY
... -------
... Bad Channels (Channel - Channel)
... ---------------------------------------------
... 0 - 32 have quality 5
... ---------------------------------------------
...
...... exiting, changes written to file : spec0.tmp
Command not found; type ? for a command listing
!xsel:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!xsel:ASCA > set datadir .
Setting data directory to /data/data16/seq_proc/55000030.005/
Setting mkf directory to /data/data16/seq_proc/55000030.005/
!xsel:ASCA > read events events.tmp
Got new instrument: SIS1
Setting: IMAGE binning = 4
WMAP binning = 8
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 4095
Got the minimum time resolution of the read data: 16.000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data16/seq_proc/55000030.005/
HK Directory is: /data/data16/seq_proc/55000030.005/
!xsel:ASCA-SIS1-BRIGHT2 > set phaname PI
!xsel:ASCA-SIS1-BRIGHT2 > filter region ad55000030s132002_0.reg
!xsel:ASCA-SIS1-BRIGHT2 > filter region SIS1_OFFCHIP.1
!xsel:ASCA-SIS1-BRIGHT2 > filter region ad55000030s110212.discrim
!xsel:ASCA-SIS1-BRIGHT2 > filter region SIS1_NOTCHIP1.1
!xsel:ASCA-SIS1-BRIGHT2 > filter region SIS1_NOTCHIP2.1
!xsel:ASCA-SIS1-BRIGHT2 > filter region SIS1_NOTCHIP3.1
!xsel:ASCA-SIS1-BRIGHT2 > extract spectrum
!xsel:ASCA-SIS1-BRIGHT2 > save spectrum spec0.tmp group=yes
Wrote spectrum to spec0.tmp
!xsel:ASCA-SIS1-BRIGHT2 > exit save_session=no
-> sis1c0p40_290296.fits already present in current directorySisrmg Version 1.1, Configured 04/97 This version resolves *all* known keyword incompatibilities with other FTOOLS tasks. If you have previously fudged *any* keywords in the PHA file to compensate, incorrect results will follow. Setting 1st PHA channel to 0 Making v1.1 1180x1024 S1C0 Bright2 PI RMF Calibration data from ./ Please stand by... ...Done.-> SIS1_NOTCHIP0.1 already present in current directory
** XSELECT V1.3 **
!> Enter session name >[xsel] xsel
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS S1CCDPOW
1 GAL_RIDG BRIGHT2 HIGH 09/04/97 21:02:58 0.70E+04 1467 1111
EXTRACTOR vers 2.0 11 Apr 1997.
Getting FITS WCS Keywords
Doing file: /data/data16/seq_proc/55000030.005/events.tmp
Total Good Bad: Region Time Phase Cut
1467 449 1018 0 0 0
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
1467 449 1018 0 0 0
in 7023.77 seconds
Spectrum has 449 counts for 6.3926E-02 counts/sec
-------------------------
MANDATORY KEYWORDS/VALUES
-------------------------
--------------------------------------------------------------------
--------------------------------------------------------------------
EXTNAME - SPECTRUM Name of this BINTABLE
TELESCOP - ASCA Mission/Satellite name
INSTRUME - SIS1 Instrument/Detector
FILTER - Instrument filter in use
EXPOSURE - 7023.8 Integration time (in secs) of PHA data
AREASCAL - 1.0000 Area scaling factor
BACKSCAL - 0.15767 Background scaling factor
BACKFILE - NONE Associated background file
CORRSCAL - 1.0000 Correlation scaling factor
CORRFILE - none Associated correlation file
RESPFILE - NONE Associated redistribution matrix file
ANCRFILE - none Associated ancillary response file
XFLT0001 - none XSPEC selection filter
POISSERR - TRUE Whether Poissonian errors apply
CHANTYPE - PI Whether channels have been corrected
TLMIN1 - 0 First legal Detector channel
DETCHANS - 1024 No. of legal detector channels
NCHAN - 1024 No. of detector channels in dataset
PHAVERSN - 1.1.0 OGIP FITS version number
STAT_ERR - FALSE Statistical Error
SYS_ERR - TRUE Fractional Systematic Error
QUALITY - TRUE Quality Flag
GROUPING - FALSE Grouping Flag
--------------------------------------------------------------------
--------------------------------------------------------------------
... QUALITY
...
... -------
... QUALITY
... -------
... Bad Channels (Channel - Channel)
... ---------------------------------------------
... 0 - 32 have quality 5
... ---------------------------------------------
...
...... exiting, changes written to file : spec1.tmp
Command not found; type ? for a command listing
!xsel:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!xsel:ASCA > set datadir .
Setting data directory to /data/data16/seq_proc/55000030.005/
Setting mkf directory to /data/data16/seq_proc/55000030.005/
!xsel:ASCA > read events events.tmp
Got new instrument: SIS1
Setting: IMAGE binning = 4
WMAP binning = 8
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 4095
Got the minimum time resolution of the read data: 16.000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data16/seq_proc/55000030.005/
HK Directory is: /data/data16/seq_proc/55000030.005/
!xsel:ASCA-SIS1-BRIGHT2 > set phaname PI
!xsel:ASCA-SIS1-BRIGHT2 > filter region ad55000030s132002_0.reg
!xsel:ASCA-SIS1-BRIGHT2 > filter region SIS1_OFFCHIP.1
!xsel:ASCA-SIS1-BRIGHT2 > filter region ad55000030s110212.discrim
!xsel:ASCA-SIS1-BRIGHT2 > filter region SIS1_NOTCHIP0.1
!xsel:ASCA-SIS1-BRIGHT2 > filter region SIS1_NOTCHIP2.1
!xsel:ASCA-SIS1-BRIGHT2 > filter region SIS1_NOTCHIP3.1
!xsel:ASCA-SIS1-BRIGHT2 > extract spectrum
!xsel:ASCA-SIS1-BRIGHT2 > save spectrum spec1.tmp group=yes
Wrote spectrum to spec1.tmp
!xsel:ASCA-SIS1-BRIGHT2 > exit save_session=no
-> sis1c1p40_290296.fits already present in current directorySisrmg Version 1.1, Configured 04/97 This version resolves *all* known keyword incompatibilities with other FTOOLS tasks. If you have previously fudged *any* keywords in the PHA file to compensate, incorrect results will follow. Setting 1st PHA channel to 0 Making v1.1 1180x1024 S1C1 Bright2 PI RMF Calibration data from ./ Please stand by... ...Done.-> SIS1_NOTCHIP0.1 already present in current directory
** XSELECT V1.3 **
!> Enter session name >[xsel] xsel
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS S1CCDPOW
1 GAL_RIDG BRIGHT2 HIGH 09/04/97 21:02:58 0.70E+04 1467 1111
EXTRACTOR vers 2.0 11 Apr 1997.
Getting FITS WCS Keywords
Doing file: /data/data16/seq_proc/55000030.005/events.tmp
Total Good Bad: Region Time Phase Cut
1467 485 982 0 0 0
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
1467 485 982 0 0 0
in 7023.77 seconds
Spectrum has 485 counts for 6.9051E-02 counts/sec
-------------------------
MANDATORY KEYWORDS/VALUES
-------------------------
--------------------------------------------------------------------
--------------------------------------------------------------------
EXTNAME - SPECTRUM Name of this BINTABLE
TELESCOP - ASCA Mission/Satellite name
INSTRUME - SIS1 Instrument/Detector
FILTER - Instrument filter in use
EXPOSURE - 7023.8 Integration time (in secs) of PHA data
AREASCAL - 1.0000 Area scaling factor
BACKSCAL - 0.15818 Background scaling factor
BACKFILE - NONE Associated background file
CORRSCAL - 1.0000 Correlation scaling factor
CORRFILE - none Associated correlation file
RESPFILE - NONE Associated redistribution matrix file
ANCRFILE - none Associated ancillary response file
XFLT0001 - none XSPEC selection filter
POISSERR - TRUE Whether Poissonian errors apply
CHANTYPE - PI Whether channels have been corrected
TLMIN1 - 0 First legal Detector channel
DETCHANS - 1024 No. of legal detector channels
NCHAN - 1024 No. of detector channels in dataset
PHAVERSN - 1.1.0 OGIP FITS version number
STAT_ERR - FALSE Statistical Error
SYS_ERR - TRUE Fractional Systematic Error
QUALITY - TRUE Quality Flag
GROUPING - FALSE Grouping Flag
--------------------------------------------------------------------
--------------------------------------------------------------------
... QUALITY
...
... -------
... QUALITY
... -------
... Bad Channels (Channel - Channel)
... ---------------------------------------------
... 0 - 32 have quality 5
... ---------------------------------------------
...
...... exiting, changes written to file : spec2.tmp
Command not found; type ? for a command listing
!xsel:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!xsel:ASCA > set datadir .
Setting data directory to /data/data16/seq_proc/55000030.005/
Setting mkf directory to /data/data16/seq_proc/55000030.005/
!xsel:ASCA > read events events.tmp
Got new instrument: SIS1
Setting: IMAGE binning = 4
WMAP binning = 8
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 4095
Got the minimum time resolution of the read data: 16.000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data16/seq_proc/55000030.005/
HK Directory is: /data/data16/seq_proc/55000030.005/
!xsel:ASCA-SIS1-BRIGHT2 > set phaname PI
!xsel:ASCA-SIS1-BRIGHT2 > filter region ad55000030s132002_0.reg
!xsel:ASCA-SIS1-BRIGHT2 > filter region SIS1_OFFCHIP.1
!xsel:ASCA-SIS1-BRIGHT2 > filter region ad55000030s110212.discrim
!xsel:ASCA-SIS1-BRIGHT2 > filter region SIS1_NOTCHIP0.1
!xsel:ASCA-SIS1-BRIGHT2 > filter region SIS1_NOTCHIP1.1
!xsel:ASCA-SIS1-BRIGHT2 > filter region SIS1_NOTCHIP3.1
!xsel:ASCA-SIS1-BRIGHT2 > extract spectrum
!xsel:ASCA-SIS1-BRIGHT2 > save spectrum spec2.tmp group=yes
Wrote spectrum to spec2.tmp
!xsel:ASCA-SIS1-BRIGHT2 > exit save_session=no
-> sis1c2p40_290296.fits already present in current directorySisrmg Version 1.1, Configured 04/97 This version resolves *all* known keyword incompatibilities with other FTOOLS tasks. If you have previously fudged *any* keywords in the PHA file to compensate, incorrect results will follow. Setting 1st PHA channel to 0 Making v1.1 1180x1024 S1C2 Bright2 PI RMF Calibration data from ./ Please stand by... ...Done.-> SIS1_NOTCHIP0.1 already present in current directory
** XSELECT V1.3 **
!> Enter session name >[xsel] xsel
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS S1CCDPOW
1 GAL_RIDG BRIGHT2 HIGH 09/04/97 21:02:58 0.70E+04 1467 1111
EXTRACTOR vers 2.0 11 Apr 1997.
Getting FITS WCS Keywords
Doing file: /data/data16/seq_proc/55000030.005/events.tmp
Total Good Bad: Region Time Phase Cut
1467 250 1217 0 0 0
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
1467 250 1217 0 0 0
in 7023.77 seconds
Spectrum has 250 counts for 3.5593E-02 counts/sec
-------------------------
MANDATORY KEYWORDS/VALUES
-------------------------
--------------------------------------------------------------------
--------------------------------------------------------------------
EXTNAME - SPECTRUM Name of this BINTABLE
TELESCOP - ASCA Mission/Satellite name
INSTRUME - SIS1 Instrument/Detector
FILTER - Instrument filter in use
EXPOSURE - 7023.8 Integration time (in secs) of PHA data
AREASCAL - 1.0000 Area scaling factor
BACKSCAL - 0.15818 Background scaling factor
BACKFILE - NONE Associated background file
CORRSCAL - 1.0000 Correlation scaling factor
CORRFILE - none Associated correlation file
RESPFILE - NONE Associated redistribution matrix file
ANCRFILE - none Associated ancillary response file
XFLT0001 - none XSPEC selection filter
POISSERR - TRUE Whether Poissonian errors apply
CHANTYPE - PI Whether channels have been corrected
TLMIN1 - 0 First legal Detector channel
DETCHANS - 1024 No. of legal detector channels
NCHAN - 1024 No. of detector channels in dataset
PHAVERSN - 1.1.0 OGIP FITS version number
STAT_ERR - FALSE Statistical Error
SYS_ERR - TRUE Fractional Systematic Error
QUALITY - TRUE Quality Flag
GROUPING - FALSE Grouping Flag
--------------------------------------------------------------------
--------------------------------------------------------------------
... QUALITY
...
... -------
... QUALITY
... -------
... Bad Channels (Channel - Channel)
... ---------------------------------------------
... 0 - 32 have quality 5
... ---------------------------------------------
...
...... exiting, changes written to file : spec3.tmp
Command not found; type ? for a command listing
!xsel:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!xsel:ASCA > set datadir .
Setting data directory to /data/data16/seq_proc/55000030.005/
Setting mkf directory to /data/data16/seq_proc/55000030.005/
!xsel:ASCA > read events events.tmp
Got new instrument: SIS1
Setting: IMAGE binning = 4
WMAP binning = 8
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 4095
Got the minimum time resolution of the read data: 16.000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data16/seq_proc/55000030.005/
HK Directory is: /data/data16/seq_proc/55000030.005/
!xsel:ASCA-SIS1-BRIGHT2 > set phaname PI
!xsel:ASCA-SIS1-BRIGHT2 > filter region ad55000030s132002_0.reg
!xsel:ASCA-SIS1-BRIGHT2 > filter region SIS1_OFFCHIP.1
!xsel:ASCA-SIS1-BRIGHT2 > filter region ad55000030s110212.discrim
!xsel:ASCA-SIS1-BRIGHT2 > filter region SIS1_NOTCHIP0.1
!xsel:ASCA-SIS1-BRIGHT2 > filter region SIS1_NOTCHIP1.1
!xsel:ASCA-SIS1-BRIGHT2 > filter region SIS1_NOTCHIP2.1
!xsel:ASCA-SIS1-BRIGHT2 > extract spectrum
!xsel:ASCA-SIS1-BRIGHT2 > save spectrum spec3.tmp group=yes
Wrote spectrum to spec3.tmp
!xsel:ASCA-SIS1-BRIGHT2 > exit save_session=no
-> sis1c3p40_290296.fits already present in current directorySisrmg Version 1.1, Configured 04/97 This version resolves *all* known keyword incompatibilities with other FTOOLS tasks. If you have previously fudged *any* keywords in the PHA file to compensate, incorrect results will follow. Setting 1st PHA channel to 0 Making v1.1 1180x1024 S1C3 Bright2 PI RMF Calibration data from ./ Please stand by... ...Done.-> Chip weights:
rmf0.tmp 0.192910702113156 rmf1.tmp 0.306066802999318 rmf2.tmp 0.330606680299932 rmf3.tmp 0.170415814587594-> Standard Output From FTOOL addrmf:
ADDRMF vers 1.10 10 April, 1997.
Summing ...
1.929E-01 * rmf0.tmp
3.061E-01 * rmf1.tmp
3.306E-01 * rmf2.tmp
1.704E-01 * rmf3.tmp
RMF # 1 : rmf0.tmp 0.19
ASCA SIS1 NONE NONE PI
RMF # 2 : rmf1.tmp 0.31
ASCA SIS1 NONE NONE PI
RMF # 3 : rmf2.tmp 0.33
ASCA SIS1 NONE NONE PI
RMF # 4 : rmf3.tmp 0.17
ASCA SIS1 NONE NONE PI
-> Generating ad55000030s110212_0.arf with point=no
ASCAARF vers 2.72 14 Mar 1997.
Input WMAP array has size 106 by 134 bins
expanded to 106 by 134 bins
First WMAP bin is at detector pixel 224 208
8 detector pixels per WMAP bin
WMAP bin size is 0.21600 mm
0.21216 arcmin
Selected region size is 543.34 arcmin^2
Optical axis is detector pixel 618.28 773.83
1180 energies from RMF file
Effective area fudge applied
Arf filter applied
Total counts in region = 1.42900E+03
Weighted mean angle from optical axis = 8.424 arcmin
-> Standard Output From STOOL group_event_files:1 ad55000030g200170h.evt 5406-> GIS2_REGION256.4 already present in current directory
ad55000030g200170h.evt-> Standard Output From FTOOL xselect:
** XSELECT V1.3 **
!> Enter session name >[xsel] xsel
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS PHA_BINS
1 GAL_RIDG PH HIGH 09/04/97 21:03:10 0.78E+04 5406 1024
EXTRACTOR vers 2.0 11 Apr 1997.
Getting FITS WCS Keywords
Doing file: /data/data16/seq_proc/55000030.005/ad55000030g200170h.evt
Total Good Bad: Region Time Phase Cut
5406 5406 0 0 0 0
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
5406 5406 0 0 0 0
in 7796.22 seconds
Spectrum has 5406 counts for 0.6934 counts/sec
-------------------------
MANDATORY KEYWORDS/VALUES
-------------------------
--------------------------------------------------------------------
--------------------------------------------------------------------
EXTNAME - SPECTRUM Name of this BINTABLE
TELESCOP - ASCA Mission/Satellite name
INSTRUME - GIS2 Instrument/Detector
FILTER - Instrument filter in use
EXPOSURE - 7796.2 Integration time (in secs) of PHA data
AREASCAL - 1.0000 Area scaling factor
BACKSCAL - 0.36888 Background scaling factor
BACKFILE - NONE Associated background file
CORRSCAL - 1.0000 Correlation scaling factor
CORRFILE - none Associated correlation file
RESPFILE - NONE Associated redistribution matrix file
ANCRFILE - none Associated ancillary response file
XFLT0001 - none XSPEC selection filter
POISSERR - TRUE Whether Poissonian errors apply
CHANTYPE - PI Whether channels have been corrected
TLMIN1 - 0 First legal Detector channel
DETCHANS - 1024 No. of legal detector channels
NCHAN - 1024 No. of detector channels in dataset
PHAVERSN - 1992a OGIP FITS version number
STAT_ERR - FALSE Statistical Error
SYS_ERR - TRUE Fractional Systematic Error
QUALITY - TRUE Quality Flag
GROUPING - FALSE Grouping Flag
--------------------------------------------------------------------
--------------------------------------------------------------------
...
... --------
... GROUPING
... --------
... ---------------------------------------------
... Channel Grouping (Channel-Channel) :
... ---------------------------------------------
...
...... exiting, changes written to file : ad55000030g210170_0.pi
Command not found; type ? for a command listing
!xsel:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!xsel:ASCA > set datadir .
Setting data directory to /data/data16/seq_proc/55000030.005/
Setting mkf directory to /data/data16/seq_proc/55000030.005/
!xsel:ASCA > read events ad55000030g200170h.evt
Got new instrument: GIS2
Setting: IMAGE binning = 1
WMAP binning = 1
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 1023
Got the minimum time resolution of the read data: 0.62500E-01
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data16/seq_proc/55000030.005/
HK Directory is: /data/data16/seq_proc/55000030.005/
!xsel:ASCA-GIS2-PH > set phaname PI
!xsel:ASCA-GIS2-PH > filter region ad55000030g225670_0.reg
!xsel:ASCA-GIS2-PH > filter region GIS2_REGION256.4
!xsel:ASCA-GIS2-PH > extract spectrum
!xsel:ASCA-GIS2-PH > save spectrum ad55000030g210170_0.pi group=yes
Wrote spectrum to ad55000030g210170_0.pi
!xsel:ASCA-GIS2-PH > exit save_session=no
-> Correcting ad55000030g210170_0.pi for dead time... read all the files from deadlist.tmp-> Grouping ad55000030g210170_0.pi to 40 counts/bin
------------------------- MANDATORY KEYWORDS/VALUES ------------------------- -------------------------------------------------------------------- -------------------------------------------------------------------- EXTNAME - SPECTRUM Name of this BINTABLE TELESCOP - ASCA Mission/Satellite name INSTRUME - GIS2 Instrument/Detector FILTER - Instrument filter in use EXPOSURE - 7796.2 Integration time (in secs) of PHA data AREASCAL - 1.0000 Area scaling factor BACKSCAL - 0.36888 Background scaling factor BACKFILE - NONE Associated background file CORRSCAL - 1.0000 Correlation scaling factor CORRFILE - none Associated correlation file RESPFILE - NONE Associated redistribution matrix file ANCRFILE - none Associated ancillary response file XFLT0001 - none XSPEC selection filter POISSERR - TRUE Whether Poissonian errors apply CHANTYPE - PI Whether channels have been corrected TLMIN1 - 0 First legal Detector channel DETCHANS - 1024 No. of legal detector channels NCHAN - 1024 No. of detector channels in dataset PHAVERSN - 1.1.0 OGIP FITS version number STAT_ERR - FALSE Statistical Error SYS_ERR - TRUE Fractional Systematic Error QUALITY - TRUE Quality Flag GROUPING - TRUE Grouping Flag -------------------------------------------------------------------- -------------------------------------------------------------------- ... ... -------- ... GROUPING ... -------- ... --------------------------------------------- ... Channel Grouping (Channel-Channel) : ... 0 - 23 are grouped by a factor 24 ... 24 - 27 are grouped by a factor 4 ... 28 - 41 are grouped by a factor 7 ... 42 - 49 are grouped by a factor 8 ... 50 - 61 are grouped by a factor 6 ... 62 - 66 are grouped by a factor 5 ... 67 - 70 are grouped by a factor 4 ... 71 - 73 are grouped by a factor 3 ... 74 - 77 are grouped by a factor 4 ... 78 - 86 are grouped by a factor 3 ... 87 - 90 are grouped by a factor 4 ... 91 - 108 are grouped by a factor 3 ... 109 - 110 are grouped by a factor 2 ... 111 - 113 are grouped by a factor 3 ... 114 - 123 are grouped by a factor 2 ... 124 - 132 are grouped by a factor 3 ... 133 - 136 are grouped by a factor 2 ... 137 - 139 are grouped by a factor 3 ... 140 - 141 are grouped by a factor 2 ... 142 - 144 are grouped by a factor 3 ... 145 - 156 are grouped by a factor 2 ... 157 - 159 are grouped by a factor 3 ... 160 - 163 are grouped by a factor 2 ... 164 - 169 are grouped by a factor 3 ... 170 - 173 are grouped by a factor 2 ... 174 - 176 are grouped by a factor 3 ... 177 - 178 are grouped by a factor 2 ... 179 - 181 are grouped by a factor 3 ... 182 - 183 are grouped by a factor 2 ... 184 - 195 are grouped by a factor 4 ... 196 - 198 are grouped by a factor 3 ... 199 - 202 are grouped by a factor 4 ... 203 - 205 are grouped by a factor 3 ... 206 - 209 are grouped by a factor 4 ... 210 - 212 are grouped by a factor 3 ... 213 - 248 are grouped by a factor 4 ... 249 - 253 are grouped by a factor 5 ... 254 - 259 are grouped by a factor 6 ... 260 - 267 are grouped by a factor 4 ... 268 - 273 are grouped by a factor 6 ... 274 - 277 are grouped by a factor 4 ... 278 - 282 are grouped by a factor 5 ... 283 - 286 are grouped by a factor 4 ... 287 - 292 are grouped by a factor 6 ... 293 - 297 are grouped by a factor 5 ... 298 - 301 are grouped by a factor 4 ... 302 - 306 are grouped by a factor 5 ... 307 - 310 are grouped by a factor 4 ... 311 - 316 are grouped by a factor 6 ... 317 - 326 are grouped by a factor 5 ... 327 - 332 are grouped by a factor 6 ... 333 - 339 are grouped by a factor 7 ... 340 - 355 are grouped by a factor 8 ... 356 - 362 are grouped by a factor 7 ... 363 - 378 are grouped by a factor 8 ... 379 - 384 are grouped by a factor 6 ... 385 - 389 are grouped by a factor 5 ... 390 - 398 are grouped by a factor 9 ... 399 - 406 are grouped by a factor 8 ... 407 - 420 are grouped by a factor 7 ... 421 - 429 are grouped by a factor 9 ... 430 - 451 are grouped by a factor 11 ... 452 - 465 are grouped by a factor 14 ... 466 - 477 are grouped by a factor 12 ... 478 - 491 are grouped by a factor 14 ... 492 - 507 are grouped by a factor 16 ... 508 - 537 are grouped by a factor 15 ... 538 - 551 are grouped by a factor 14 ... 552 - 564 are grouped by a factor 13 ... 565 - 579 are grouped by a factor 15 ... 580 - 601 are grouped by a factor 22 ... 602 - 669 are grouped by a factor 34 ... 670 - 702 are grouped by a factor 33 ... 703 - 751 are grouped by a factor 49 ... 752 - 804 are grouped by a factor 53 ... 805 - 897 are grouped by a factor 93 ... 898 - 985 are grouped by a factor 88 ... 986 - 1023 of undefined grouping (Channel quality=bad) ... --------------------------------------------- ... ...... exiting, changes written to file : ad55000030g210170_0.pi ** grppha 2.6.0 completed successfully-> Fetching gis2v4_0.rmf
ASCAARF vers 2.72 14 Mar 1997.
Input WMAP array has size 177 by 178 bins
expanded to 256 by 256 bins
First WMAP bin is at detector pixel 3 2
1 detector pixels per WMAP bin
WMAP bin size is 0.25000 mm
0.24555 arcmin
Selected region size is 1458.0 arcmin^2
Optical axis is detector pixel 133.00 130.96
201 energies from RMF file
Effective area fudge applied
Arf filter applied
Total counts in region = 5.40600E+03
Weighted mean angle from optical axis = 13.446 arcmin
-> Standard Output From STOOL group_event_files:1 ad55000030g300170h.evt 5519-> GIS3_REGION256.4 already present in current directory
ad55000030g300170h.evt-> Standard Output From FTOOL xselect:
** XSELECT V1.3 **
!> Enter session name >[xsel] xsel
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS PHA_BINS
1 GAL_RIDG PH HIGH 09/04/97 21:03:10 0.78E+04 5519 1024
EXTRACTOR vers 2.0 11 Apr 1997.
Getting FITS WCS Keywords
Doing file: /data/data16/seq_proc/55000030.005/ad55000030g300170h.evt
Total Good Bad: Region Time Phase Cut
5519 5519 0 0 0 0
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
5519 5519 0 0 0 0
in 7788.22 seconds
Spectrum has 5519 counts for 0.7086 counts/sec
-------------------------
MANDATORY KEYWORDS/VALUES
-------------------------
--------------------------------------------------------------------
--------------------------------------------------------------------
EXTNAME - SPECTRUM Name of this BINTABLE
TELESCOP - ASCA Mission/Satellite name
INSTRUME - GIS3 Instrument/Detector
FILTER - Instrument filter in use
EXPOSURE - 7788.2 Integration time (in secs) of PHA data
AREASCAL - 1.0000 Area scaling factor
BACKSCAL - 0.36783 Background scaling factor
BACKFILE - NONE Associated background file
CORRSCAL - 1.0000 Correlation scaling factor
CORRFILE - none Associated correlation file
RESPFILE - NONE Associated redistribution matrix file
ANCRFILE - none Associated ancillary response file
XFLT0001 - none XSPEC selection filter
POISSERR - TRUE Whether Poissonian errors apply
CHANTYPE - PI Whether channels have been corrected
TLMIN1 - 0 First legal Detector channel
DETCHANS - 1024 No. of legal detector channels
NCHAN - 1024 No. of detector channels in dataset
PHAVERSN - 1992a OGIP FITS version number
STAT_ERR - FALSE Statistical Error
SYS_ERR - TRUE Fractional Systematic Error
QUALITY - TRUE Quality Flag
GROUPING - FALSE Grouping Flag
--------------------------------------------------------------------
--------------------------------------------------------------------
...
... --------
... GROUPING
... --------
... ---------------------------------------------
... Channel Grouping (Channel-Channel) :
... ---------------------------------------------
...
...... exiting, changes written to file : ad55000030g310170_0.pi
Command not found; type ? for a command listing
!xsel:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!xsel:ASCA > set datadir .
Setting data directory to /data/data16/seq_proc/55000030.005/
Setting mkf directory to /data/data16/seq_proc/55000030.005/
!xsel:ASCA > read events ad55000030g300170h.evt
Got new instrument: GIS3
Setting: IMAGE binning = 1
WMAP binning = 1
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 1023
Got the minimum time resolution of the read data: 0.62500E-01
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data16/seq_proc/55000030.005/
HK Directory is: /data/data16/seq_proc/55000030.005/
!xsel:ASCA-GIS3-PH > set phaname PI
!xsel:ASCA-GIS3-PH > filter region ad55000030g325670_0.reg
!xsel:ASCA-GIS3-PH > filter region GIS3_REGION256.4
!xsel:ASCA-GIS3-PH > extract spectrum
!xsel:ASCA-GIS3-PH > save spectrum ad55000030g310170_0.pi group=yes
Wrote spectrum to ad55000030g310170_0.pi
!xsel:ASCA-GIS3-PH > exit save_session=no
-> Correcting ad55000030g310170_0.pi for dead time... read all the files from deadlist.tmp-> Grouping ad55000030g310170_0.pi to 40 counts/bin
------------------------- MANDATORY KEYWORDS/VALUES ------------------------- -------------------------------------------------------------------- -------------------------------------------------------------------- EXTNAME - SPECTRUM Name of this BINTABLE TELESCOP - ASCA Mission/Satellite name INSTRUME - GIS3 Instrument/Detector FILTER - Instrument filter in use EXPOSURE - 7788.2 Integration time (in secs) of PHA data AREASCAL - 1.0000 Area scaling factor BACKSCAL - 0.36783 Background scaling factor BACKFILE - NONE Associated background file CORRSCAL - 1.0000 Correlation scaling factor CORRFILE - none Associated correlation file RESPFILE - NONE Associated redistribution matrix file ANCRFILE - none Associated ancillary response file XFLT0001 - none XSPEC selection filter POISSERR - TRUE Whether Poissonian errors apply CHANTYPE - PI Whether channels have been corrected TLMIN1 - 0 First legal Detector channel DETCHANS - 1024 No. of legal detector channels NCHAN - 1024 No. of detector channels in dataset PHAVERSN - 1.1.0 OGIP FITS version number STAT_ERR - FALSE Statistical Error SYS_ERR - TRUE Fractional Systematic Error QUALITY - TRUE Quality Flag GROUPING - TRUE Grouping Flag -------------------------------------------------------------------- -------------------------------------------------------------------- ... ... -------- ... GROUPING ... -------- ... --------------------------------------------- ... Channel Grouping (Channel-Channel) : ... 0 - 24 are grouped by a factor 25 ... 25 - 29 are grouped by a factor 5 ... 30 - 36 are grouped by a factor 7 ... 37 - 60 are grouped by a factor 8 ... 61 - 65 are grouped by a factor 5 ... 66 - 68 are grouped by a factor 3 ... 69 - 73 are grouped by a factor 5 ... 74 - 77 are grouped by a factor 4 ... 78 - 80 are grouped by a factor 3 ... 81 - 84 are grouped by a factor 4 ... 85 - 99 are grouped by a factor 3 ... 100 - 101 are grouped by a factor 2 ... 102 - 104 are grouped by a factor 3 ... 105 - 106 are grouped by a factor 2 ... 107 - 109 are grouped by a factor 3 ... 110 - 113 are grouped by a factor 2 ... 114 - 122 are grouped by a factor 3 ... 123 - 128 are grouped by a factor 2 ... 129 - 131 are grouped by a factor 3 ... 132 - 133 are grouped by a factor 2 ... 134 - 136 are grouped by a factor 3 ... 137 - 152 are grouped by a factor 2 ... 153 - 155 are grouped by a factor 3 ... 156 - 165 are grouped by a factor 2 ... 166 - 168 are grouped by a factor 3 ... 169 - 172 are grouped by a factor 2 ... 173 - 175 are grouped by a factor 3 ... 176 - 177 are grouped by a factor 2 ... 178 - 183 are grouped by a factor 3 ... 184 - 187 are grouped by a factor 4 ... 188 - 190 are grouped by a factor 3 ... 191 - 210 are grouped by a factor 4 ... 211 - 213 are grouped by a factor 3 ... 214 - 225 are grouped by a factor 4 ... 226 - 230 are grouped by a factor 5 ... 231 - 236 are grouped by a factor 3 ... 237 - 244 are grouped by a factor 4 ... 245 - 249 are grouped by a factor 5 ... 250 - 261 are grouped by a factor 4 ... 262 - 266 are grouped by a factor 5 ... 267 - 269 are grouped by a factor 3 ... 270 - 309 are grouped by a factor 5 ... 310 - 315 are grouped by a factor 6 ... 316 - 322 are grouped by a factor 7 ... 323 - 328 are grouped by a factor 6 ... 329 - 335 are grouped by a factor 7 ... 336 - 341 are grouped by a factor 6 ... 342 - 348 are grouped by a factor 7 ... 349 - 354 are grouped by a factor 6 ... 355 - 362 are grouped by a factor 8 ... 363 - 369 are grouped by a factor 7 ... 370 - 375 are grouped by a factor 6 ... 376 - 389 are grouped by a factor 7 ... 390 - 397 are grouped by a factor 8 ... 398 - 404 are grouped by a factor 7 ... 405 - 413 are grouped by a factor 9 ... 414 - 425 are grouped by a factor 12 ... 426 - 433 are grouped by a factor 8 ... 434 - 444 are grouped by a factor 11 ... 445 - 459 are grouped by a factor 15 ... 460 - 485 are grouped by a factor 13 ... 486 - 515 are grouped by a factor 15 ... 516 - 529 are grouped by a factor 14 ... 530 - 544 are grouped by a factor 15 ... 545 - 553 are grouped by a factor 9 ... 554 - 570 are grouped by a factor 17 ... 571 - 583 are grouped by a factor 13 ... 584 - 605 are grouped by a factor 22 ... 606 - 629 are grouped by a factor 24 ... 630 - 663 are grouped by a factor 34 ... 664 - 692 are grouped by a factor 29 ... 693 - 719 are grouped by a factor 27 ... 720 - 764 are grouped by a factor 45 ... 765 - 825 are grouped by a factor 61 ... 826 - 880 are grouped by a factor 55 ... 881 - 943 are grouped by a factor 63 ... 944 - 1023 of undefined grouping (Channel quality=bad) ... --------------------------------------------- ... ...... exiting, changes written to file : ad55000030g310170_0.pi ** grppha 2.6.0 completed successfully-> Fetching gis3v4_0.rmf
ASCAARF vers 2.72 14 Mar 1997.
Input WMAP array has size 177 by 178 bins
expanded to 256 by 256 bins
First WMAP bin is at detector pixel 3 2
1 detector pixels per WMAP bin
WMAP bin size is 0.25000 mm
0.24555 arcmin
Selected region size is 1453.8 arcmin^2
Optical axis is detector pixel 119.36 134.44
201 energies from RMF file
Effective area fudge applied
Arf filter applied
Total counts in region = 5.51900E+03
Weighted mean angle from optical axis = 13.175 arcmin
-> Plotting ad55000030g210170_0_pi.ps from ad55000030g210170_0.pi
XSPEC 9.01 20:53:14 25-May-98
Plot device not set, use "cpd" to set it
Type "help" or "?" for further information
!XSPEC> data ad55000030g210170_0.pi
Net count rate (cts/s) for file 1 0.6934 +/- 9.4562E-03
1 data set is in use
!XSPEC> setplot energy
!XSPEC> ignore bad
!XSPEC> iplot
!PLT> log y on
!PLT> rescale y
!PLT> hard /ps
!PLT> quit
!XSPEC> exit
!Do you really want to exit (y) y
XSPEC: quit
-> Plotting ad55000030g310170_0_pi.ps from ad55000030g310170_0.pi
XSPEC 9.01 20:53:32 25-May-98
Plot device not set, use "cpd" to set it
Type "help" or "?" for further information
!XSPEC> data ad55000030g310170_0.pi
Net count rate (cts/s) for file 1 0.7086 +/- 9.5862E-03
1 data set is in use
!XSPEC> setplot energy
!XSPEC> ignore bad
!XSPEC> iplot
!PLT> log y on
!PLT> rescale y
!PLT> hard /ps
!PLT> quit
!XSPEC> exit
!Do you really want to exit (y) y
XSPEC: quit
-> Plotting ad55000030s010102_0_pi.ps from ad55000030s010102_0.pi
XSPEC 9.01 20:53:46 25-May-98
Plot device not set, use "cpd" to set it
Type "help" or "?" for further information
!XSPEC> data ad55000030s010102_0.pi
Net count rate (cts/s) for file 1 0.1630 +/- 5.4247E-03
1 data set is in use
!XSPEC> setplot energy
!XSPEC> ignore bad
!XSPEC> iplot
!PLT> log y on
!PLT> rescale y
!PLT> hard /ps
!PLT> quit
!XSPEC> exit
!Do you really want to exit (y) y
XSPEC: quit
-> Plotting ad55000030s010212_0_pi.ps from ad55000030s010212_0.pi
XSPEC 9.01 20:54:02 25-May-98
Plot device not set, use "cpd" to set it
Type "help" or "?" for further information
!XSPEC> data ad55000030s010212_0.pi
Net count rate (cts/s) for file 1 0.2197 +/- 6.4352E-03
1 data set is in use
!XSPEC> setplot energy
!XSPEC> ignore bad
!XSPEC> iplot
!PLT> log y on
!PLT> rescale y
!PLT> hard /ps
!PLT> quit
!XSPEC> exit
!Do you really want to exit (y) y
XSPEC: quit
-> Plotting ad55000030s110102_0_pi.ps from ad55000030s110102_0.pi
XSPEC 9.01 20:54:20 25-May-98
Plot device not set, use "cpd" to set it
Type "help" or "?" for further information
!XSPEC> data ad55000030s110102_0.pi
Net count rate (cts/s) for file 1 0.1150 +/- 4.5702E-03
1 data set is in use
!XSPEC> setplot energy
!XSPEC> ignore bad
!XSPEC> iplot
!PLT> log y on
!PLT> rescale y
!PLT> hard /ps
!PLT> quit
!XSPEC> exit
!Do you really want to exit (y) y
XSPEC: quit
-> Plotting ad55000030s110212_0_pi.ps from ad55000030s110212_0.pi
XSPEC 9.01 20:54:36 25-May-98
Plot device not set, use "cpd" to set it
Type "help" or "?" for further information
!XSPEC> data ad55000030s110212_0.pi
Net count rate (cts/s) for file 1 0.2089 +/- 5.5141E-03
1 data set is in use
!XSPEC> setplot energy
!XSPEC> ignore bad
!XSPEC> iplot
!PLT> log y on
!PLT> rescale y
!PLT> hard /ps
!PLT> quit
!XSPEC> exit
!Do you really want to exit (y) y
XSPEC: quit
** XSELECT V1.3 **
!> Enter session name >[xsel] xsel
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS S0CCDPOW
1 GAL_RIDG BRIGHT HIGH 09/04/97 21:55:34 0.41E+03 137 1111
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS S0CCDPOW
1 GAL_RIDG BRIGHT HIGH 09/04/97 21:55:34 0.41E+03 137 1111
2 GAL_RIDG BRIGHT HIGH 09/04/97 21:02:58 0.65E+04 1022 1111
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS S0CCDPOW
1 GAL_RIDG BRIGHT HIGH 09/04/97 21:55:34 0.41E+03 137 1111
2 GAL_RIDG BRIGHT HIGH 09/04/97 21:02:58 0.65E+04 1022 1111
3 GAL_RIDG BRIGHT MEDIUM 09/04/97 20:51:26 0.80E+02 77 1111
EXTRACTOR vers 2.0 11 Apr 1997.
Doing file: /data/data16/seq_proc/55000030.005/ad55000030s000102h.evt
Total Good Bad: Region Time Phase Cut
137 137 0 0 0 0
Writing events file
137 events written to the output file
Doing file: /data/data16/seq_proc/55000030.005/ad55000030s000202h.evt
Total Good Bad: Region Time Phase Cut
1022 1022 0 0 0 0
Writing events file
1159 events written to the output file
Doing file: /data/data16/seq_proc/55000030.005/ad55000030s000302m.evt
Total Good Bad: Region Time Phase Cut
77 77 0 0 0 0
Writing events file
1236 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
1236 1236 0 0 0 0
in 6983.70 seconds
Command not found; type ? for a command listing
!xsel:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!xsel:ASCA > set datadir .
Setting data directory to /data/data16/seq_proc/55000030.005/
Setting mkf directory to /data/data16/seq_proc/55000030.005/
!xsel:ASCA > read events ad55000030s000102h.evt
Got new instrument: SIS0
Setting: IMAGE binning = 4
WMAP binning = 8
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 2047
Got the minimum time resolution of the read data: 16.000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data16/seq_proc/55000030.005/
HK Directory is: /data/data16/seq_proc/55000030.005/
!xsel:ASCA-SIS0-BRIGHT > read events ad55000030s000202h.evt
Getting Min and Max for Energy Column...
Got min and max for PI: 0 2047
Got the minimum time resolution of the read data: 16.000
Number of files read in: 2
******************** Observation Catalogue ********************
Data Directory is: /data/data16/seq_proc/55000030.005/
HK Directory is: /data/data16/seq_proc/55000030.005/
!xsel:ASCA-SIS0-BRIGHT > read events ad55000030s000302m.evt
Getting Min and Max for Energy Column...
Got min and max for PI: 0 2047
Got the minimum time resolution of the read data: 16.000
Number of files read in: 3
******************** Observation Catalogue ********************
Data Directory is: /data/data16/seq_proc/55000030.005/
HK Directory is: /data/data16/seq_proc/55000030.005/
!xsel:ASCA-SIS0-BRIGHT > filter region ad55000030s032002_0.reg
!xsel:ASCA-SIS0-BRIGHT > extract events
!xsel:ASCA-SIS0-BRIGHT > save events outfile=events.tmp use_events=yes
Wrote events list to file events.tmp
Changing Data directory from:
/data/data16/seq_proc/55000030.005/
to the current working directory.
!xsel:ASCA-SIS0-BRIGHT > exit save_session=no
-> Extracting ad55000030s000002_0.lc with binsize 282.512018227992
** XSELECT V1.3 **
!> Enter session name >[xsel] xsel
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS S0CCDPOW
1 GAL_RIDG BRIGHT HIGH 09/04/97 20:51:26 0.70E+04 1236 1111
EXTRACTOR vers 2.0 11 Apr 1997.
Doing file: /data/data16/seq_proc/55000030.005/events.tmp
Total Good Bad: Region Time Phase Cut
1236 1236 0 0 0 0
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
1236 1236 0 0 0 0
in 6983.70 seconds
Fits light curve has 1236 counts for 0.1770 counts/sec
Thresholding removed significant counts
Try exposure=0.0 on the extract command in xselect
or lcthresh=0.0 if running extractor stand-alone
Command not found; type ? for a command listing
!xsel:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!xsel:ASCA > set datadir .
Setting data directory to /data/data16/seq_proc/55000030.005/
Setting mkf directory to /data/data16/seq_proc/55000030.005/
!xsel:ASCA > read events events.tmp
Got new instrument: SIS0
Setting: IMAGE binning = 4
WMAP binning = 8
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 2047
Got the minimum time resolution of the read data: 16.000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data16/seq_proc/55000030.005/
HK Directory is: /data/data16/seq_proc/55000030.005/
!xsel:ASCA-SIS0-BRIGHT > set binsize 282.512018227992
!xsel:ASCA-SIS0-BRIGHT > extract curve exposure=0.5
!xsel:ASCA-SIS0-BRIGHT > save curve ad55000030s000002_0.lc
Wrote FITS light curve to file ad55000030s000002_0.lc
!xsel:ASCA-SIS0-BRIGHT > exit save_session=no
-> Plotting light curve ad55000030s000002_0_lc.ps
Type "help" for information
[1]xronos> Current User Interface is ; command driven
[2]xronos> Enter up to 50 input filenames and options for series 1 (or rtn)
Ser. A filename 1 +options[.rbf]=> ad55000030s000002_0.lc
Selected FITS extensions: 1 - RATE TABLE;
Source ............ GAL_RIDGE_7_N4 Start Time (d) .... 10547 21:04:14.245
FITS Extension .... 1 - `RATE ` Stop Time (d) ..... 10548 05:55:26.245
No. of Rows ....... 25 Bin Time (s) ...... 282.5
Right Ascension ... 2.7568E+02 Internal time sys.. Converted to TJD
Declination ....... -1.3702E+01 Experiment ........ ASCA SIS0
Corrections applied: Vignetting - No ; Deadtime - No ; Bkgd - No ; Clock - No
Selected Columns: 1 - Time; 2 - Y-axis; 3 - Y-error;
File contains binned data.
Ser. A filename 2 +options[.rbf]=>
Enter up to 50 input filenames and options for series 2 (or rtn)
Ser. B filename 1 +options[.rbf]=>
Enter up to 50 input filenames and options for series 3 (or rtn)
Ser. C filename 1 +options[.rbf]=>
[3]xronos>
Maximum of 1 Intvs. with 113 Newbins of 282.512 (s)
Intv 1 Start10547 21: 6:35
Ser.1 Avg 0.1725 Chisq 118.2 Var 0.3297E-02 Newbs. 25
Min 0.9911E-01 Max 0.4083 expVar 0.6977E-03 Bins 25
Results from Statistical Analysis
Newbin Integration Time (s).. 282.51
Interval Duration (s)........ 31641.
No. of Newbins .............. 25
Average (c/s) ............... 0.17252 +/- 0.54E-02
Standard Deviation (c/s)..... 0.57424E-01
Minimum (c/s)................ 0.99111E-01
Maximum (c/s)................ 0.40833
Variance ((c/s)**2).......... 0.32975E-02 +/- 0.95E-03
Expected Variance ((c/s)**2). 0.69771E-03 +/- 0.20E-03
Third Moment ((c/s)**3)...... 0.51830E-03
Average Deviation (c/s)...... 0.34616E-01
Skewness..................... 2.7372 +/- 0.49
Kurtosis..................... 8.7072 +/- 0.98
RMS fractional variation..... 0.29554 +/- 0.54E-01
Chi-Square................... 118.15 dof 24
Chi-Square Prob of constancy. 0.20671E-13 (0 means < 1.e-38)
Kolm.-Smir. Prob of constancy 0.17382E-03 (0 means < 1.e-38)
[4]xronos> [5]xronos>
Maximum of 1 Intvs. with 113 Newbins of 282.512 (s)
Intv 1 Start10547 21: 6:35
Ser.1 Avg 0.1725 Chisq 118.2 Var 0.3297E-02 Newbs. 25
Min 0.9911E-01 Max 0.4083 expVar 0.6977E-03 Bins 25
Light curve ready !
Frme 1 Written to output file : xronos.qlc1
PLT> PLT> PLT> [6]xronos>
-> TIMEDEL=1.6000000000E+01 for ad55000030s100102h.evt
** XSELECT V1.3 **
!> Enter session name >[xsel] xsel
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS S1CCDPOW
1 GAL_RIDG BRIGHT HIGH 09/04/97 21:02:58 0.70E+04 740 1111
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS S1CCDPOW
1 GAL_RIDG BRIGHT HIGH 09/04/97 21:02:58 0.70E+04 740 1111
2 GAL_RIDG BRIGHT HIGH 10/04/97 02:43:42 0.16E+02 44 1111
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS S1CCDPOW
1 GAL_RIDG BRIGHT HIGH 09/04/97 21:02:58 0.70E+04 740 1111
2 GAL_RIDG BRIGHT HIGH 10/04/97 02:43:42 0.16E+02 44 1111
3 GAL_RIDG BRIGHT MEDIUM 09/04/97 20:51:26 0.80E+02 57 1111
EXTRACTOR vers 2.0 11 Apr 1997.
Doing file: /data/data16/seq_proc/55000030.005/ad55000030s100102h.evt
Total Good Bad: Region Time Phase Cut
740 740 0 0 0 0
Writing events file
740 events written to the output file
Doing file: /data/data16/seq_proc/55000030.005/ad55000030s100202h.evt
Total Good Bad: Region Time Phase Cut
44 44 0 0 0 0
Writing events file
784 events written to the output file
Doing file: /data/data16/seq_proc/55000030.005/ad55000030s100302m.evt
Total Good Bad: Region Time Phase Cut
57 57 0 0 0 0
Writing events file
841 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
841 841 0 0 0 0
in 7103.77 seconds
Command not found; type ? for a command listing
!xsel:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!xsel:ASCA > set datadir .
Setting data directory to /data/data16/seq_proc/55000030.005/
Setting mkf directory to /data/data16/seq_proc/55000030.005/
!xsel:ASCA > read events ad55000030s100102h.evt
Got new instrument: SIS1
Setting: IMAGE binning = 4
WMAP binning = 8
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 2047
Got the minimum time resolution of the read data: 16.000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data16/seq_proc/55000030.005/
HK Directory is: /data/data16/seq_proc/55000030.005/
!xsel:ASCA-SIS1-BRIGHT > read events ad55000030s100202h.evt
Getting Min and Max for Energy Column...
Got min and max for PI: 0 2047
Got the minimum time resolution of the read data: 16.000
Number of files read in: 2
******************** Observation Catalogue ********************
Data Directory is: /data/data16/seq_proc/55000030.005/
HK Directory is: /data/data16/seq_proc/55000030.005/
!xsel:ASCA-SIS1-BRIGHT > read events ad55000030s100302m.evt
Getting Min and Max for Energy Column...
Got min and max for PI: 0 2047
Got the minimum time resolution of the read data: 16.000
Number of files read in: 3
******************** Observation Catalogue ********************
Data Directory is: /data/data16/seq_proc/55000030.005/
HK Directory is: /data/data16/seq_proc/55000030.005/
!xsel:ASCA-SIS1-BRIGHT > filter region ad55000030s132002_0.reg
!xsel:ASCA-SIS1-BRIGHT > extract events
!xsel:ASCA-SIS1-BRIGHT > save events outfile=events.tmp use_events=yes
Wrote events list to file events.tmp
Changing Data directory from:
/data/data16/seq_proc/55000030.005/
to the current working directory.
!xsel:ASCA-SIS1-BRIGHT > exit save_session=no
-> Extracting ad55000030s100002_0.lc with binsize 422.340655291407
** XSELECT V1.3 **
!> Enter session name >[xsel] xsel
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS S1CCDPOW
1 GAL_RIDG BRIGHT HIGH 09/04/97 20:51:26 0.71E+04 841 1111
EXTRACTOR vers 2.0 11 Apr 1997.
Doing file: /data/data16/seq_proc/55000030.005/events.tmp
Total Good Bad: Region Time Phase Cut
841 841 0 0 0 0
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
841 841 0 0 0 0
in 7103.77 seconds
Fits light curve has 841 counts for 0.1184 counts/sec
Thresholding removed significant counts
Try exposure=0.0 on the extract command in xselect
or lcthresh=0.0 if running extractor stand-alone
Command not found; type ? for a command listing
!xsel:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!xsel:ASCA > set datadir .
Setting data directory to /data/data16/seq_proc/55000030.005/
Setting mkf directory to /data/data16/seq_proc/55000030.005/
!xsel:ASCA > read events events.tmp
Got new instrument: SIS1
Setting: IMAGE binning = 4
WMAP binning = 8
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 2047
Got the minimum time resolution of the read data: 16.000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data16/seq_proc/55000030.005/
HK Directory is: /data/data16/seq_proc/55000030.005/
!xsel:ASCA-SIS1-BRIGHT > set binsize 422.340655291407
!xsel:ASCA-SIS1-BRIGHT > extract curve exposure=0.5
!xsel:ASCA-SIS1-BRIGHT > save curve ad55000030s100002_0.lc
Wrote FITS light curve to file ad55000030s100002_0.lc
!xsel:ASCA-SIS1-BRIGHT > exit save_session=no
-> Plotting light curve ad55000030s100002_0_lc.ps
Type "help" for information
[1]xronos> Current User Interface is ; command driven
[2]xronos> Enter up to 50 input filenames and options for series 1 (or rtn)
Ser. A filename 1 +options[.rbf]=> ad55000030s100002_0.lc
Selected FITS extensions: 1 - RATE TABLE;
Source ............ GAL_RIDGE_7_N4 Start Time (d) .... 10547 21:04:14.245
FITS Extension .... 1 - `RATE ` Stop Time (d) ..... 10548 05:55:26.245
No. of Rows ....... 17 Bin Time (s) ...... 422.3
Right Ascension ... 2.7568E+02 Internal time sys.. Converted to TJD
Declination ....... -1.3702E+01 Experiment ........ ASCA SIS1
Corrections applied: Vignetting - No ; Deadtime - No ; Bkgd - No ; Clock - No
Selected Columns: 1 - Time; 2 - Y-axis; 3 - Y-error;
File contains binned data.
Ser. A filename 2 +options[.rbf]=>
Enter up to 50 input filenames and options for series 2 (or rtn)
Ser. B filename 1 +options[.rbf]=>
Enter up to 50 input filenames and options for series 3 (or rtn)
Ser. C filename 1 +options[.rbf]=>
[3]xronos>
Maximum of 1 Intvs. with 76 Newbins of 422.341 (s)
Intv 1 Start10547 21: 7:45
Ser.1 Avg 0.1197 Chisq 155.9 Var 0.3198E-02 Newbs. 17
Min 0.7552E-01 Max 0.3374 expVar 0.3486E-03 Bins 17
Results from Statistical Analysis
Newbin Integration Time (s).. 422.34
Interval Duration (s)........ 31253.
No. of Newbins .............. 17
Average (c/s) ............... 0.11966 +/- 0.47E-02
Standard Deviation (c/s)..... 0.56547E-01
Minimum (c/s)................ 0.75521E-01
Maximum (c/s)................ 0.33744
Variance ((c/s)**2).......... 0.31975E-02 +/- 0.11E-02
Expected Variance ((c/s)**2). 0.34861E-03 +/- 0.12E-03
Third Moment ((c/s)**3)...... 0.59576E-03
Average Deviation (c/s)...... 0.29398E-01
Skewness..................... 3.2949 +/- 0.59
Kurtosis..................... 9.9836 +/- 1.2
RMS fractional variation..... 0.44607 +/- 0.89E-01
Chi-Square................... 155.93 dof 16
Chi-Square Prob of constancy. 0.52630E-24 (0 means < 1.e-38)
Kolm.-Smir. Prob of constancy 0.13036E-11 (0 means < 1.e-38)
[4]xronos> [5]xronos>
Maximum of 1 Intvs. with 76 Newbins of 422.341 (s)
Intv 1 Start10547 21: 7:45
Ser.1 Avg 0.1197 Chisq 155.9 Var 0.3198E-02 Newbs. 17
Min 0.7552E-01 Max 0.3374 expVar 0.3486E-03 Bins 17
Light curve ready !
Frme 1 Written to output file : xronos.qlc1
PLT> PLT> PLT> [6]xronos>
-> TIMEDEL=6.2500000000E-02 for ad55000030g200170h.evt
** XSELECT V1.3 **
!> Enter session name >[xsel] xsel
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS PHA_BINS
1 GAL_RIDG PH HIGH 09/04/97 21:03:10 0.78E+04 5406 1024
EXTRACTOR vers 2.0 11 Apr 1997.
Doing file: /data/data16/seq_proc/55000030.005/ad55000030g200170h.evt
Total Good Bad: Region Time Phase Cut
5406 5406 0 0 0 0
Writing events file
5406 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
5406 5406 0 0 0 0
in 7796.22 seconds
Command not found; type ? for a command listing
!xsel:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!xsel:ASCA > set datadir .
Setting data directory to /data/data16/seq_proc/55000030.005/
Setting mkf directory to /data/data16/seq_proc/55000030.005/
!xsel:ASCA > read events ad55000030g200170h.evt
Got new instrument: GIS2
Setting: IMAGE binning = 1
WMAP binning = 1
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 1023
Got the minimum time resolution of the read data: 0.62500E-01
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data16/seq_proc/55000030.005/
HK Directory is: /data/data16/seq_proc/55000030.005/
!xsel:ASCA-GIS2-PH > filter region ad55000030g225670_0.reg
!xsel:ASCA-GIS2-PH > extract events
!xsel:ASCA-GIS2-PH > save events outfile=events.tmp use_events=yes
Wrote events list to file events.tmp
Changing Data directory from:
/data/data16/seq_proc/55000030.005/
to the current working directory.
!xsel:ASCA-GIS2-PH > exit save_session=no
-> Extracting ad55000030g200070_0.lc with binsize 72.107098318562
** XSELECT V1.3 **
!> Enter session name >[xsel] xsel
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS PHA_BINS
1 GAL_RIDG PH HIGH 09/04/97 21:03:10 0.78E+04 5406 1024
EXTRACTOR vers 2.0 11 Apr 1997.
Doing file: /data/data16/seq_proc/55000030.005/events.tmp
Total Good Bad: Region Time Phase Cut
5406 5406 0 0 0 0
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
5406 5406 0 0 0 0
in 7796.22 seconds
Fits light curve has 5406 counts for 0.6934 counts/sec
Command not found; type ? for a command listing
!xsel:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!xsel:ASCA > set datadir .
Setting data directory to /data/data16/seq_proc/55000030.005/
Setting mkf directory to /data/data16/seq_proc/55000030.005/
!xsel:ASCA > read events events.tmp
Got new instrument: GIS2
Setting: IMAGE binning = 1
WMAP binning = 1
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 1023
Got the minimum time resolution of the read data: 0.62500E-01
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data16/seq_proc/55000030.005/
HK Directory is: /data/data16/seq_proc/55000030.005/
!xsel:ASCA-GIS2-PH > set binsize 72.107098318562
!xsel:ASCA-GIS2-PH > extract curve exposure=0.5
!xsel:ASCA-GIS2-PH > save curve ad55000030g200070_0.lc
Wrote FITS light curve to file ad55000030g200070_0.lc
!xsel:ASCA-GIS2-PH > exit save_session=no
-> Plotting light curve ad55000030g200070_0_lc.ps
Type "help" for information
[1]xronos> Current User Interface is ; command driven
[2]xronos> Enter up to 50 input filenames and options for series 1 (or rtn)
Ser. A filename 1 +options[.rbf]=> ad55000030g200070_0.lc
Selected FITS extensions: 1 - RATE TABLE;
Source ............ GAL_RIDGE_7_N4 Start Time (d) .... 10547 21:03:10.245
FITS Extension .... 1 - `RATE ` Stop Time (d) ..... 10548 05:59:10.245
No. of Rows ....... 112 Bin Time (s) ...... 72.11
Right Ascension ... 2.7568E+02 Internal time sys.. Converted to TJD
Declination ....... -1.3702E+01 Experiment ........ ASCA GIS2
Corrections applied: Vignetting - No ; Deadtime - No ; Bkgd - No ; Clock - No
Selected Columns: 1 - Time; 2 - Y-axis; 3 - Y-error;
File contains binned data.
Ser. A filename 2 +options[.rbf]=>
Enter up to 50 input filenames and options for series 2 (or rtn)
Ser. B filename 1 +options[.rbf]=>
Enter up to 50 input filenames and options for series 3 (or rtn)
Ser. C filename 1 +options[.rbf]=>
[3]xronos>
Maximum of 1 Intvs. with 447 Newbins of 72.1071 (s)
Intv 1 Start10547 21: 3:46
Ser.1 Avg 0.6946 Chisq 104.5 Var 0.9778E-02 Newbs. 112
Min 0.4577 Max 0.9985 expVar 0.1048E-01 Bins 112
Results from Statistical Analysis
Newbin Integration Time (s).. 72.107
Interval Duration (s)........ 32088.
No. of Newbins .............. 112
Average (c/s) ............... 0.69460 +/- 0.97E-02
Standard Deviation (c/s)..... 0.98883E-01
Minimum (c/s)................ 0.45765
Maximum (c/s)................ 0.99851
Variance ((c/s)**2).......... 0.97778E-02 +/- 0.13E-02
Expected Variance ((c/s)**2). 0.10482E-01 +/- 0.14E-02
Third Moment ((c/s)**3)...... 0.30714E-03
Average Deviation (c/s)...... 0.78573E-01
Skewness..................... 0.31767 +/- 0.23
Kurtosis..................... 0.14549 +/- 0.46
RMS fractional variation....< 0.10615 (3 sigma)
Chi-Square................... 104.47 dof 111
Chi-Square Prob of constancy. 0.65613 (0 means < 1.e-38)
Kolm.-Smir. Prob of constancy 0.61952E-01 (0 means < 1.e-38)
[4]xronos> [5]xronos>
Maximum of 1 Intvs. with 447 Newbins of 72.1071 (s)
Intv 1 Start10547 21: 3:46
Ser.1 Avg 0.6946 Chisq 104.5 Var 0.9778E-02 Newbs. 112
Min 0.4577 Max 0.9985 expVar 0.1048E-01 Bins 112
Light curve ready !
Frme 1 Written to output file : xronos.qlc1
PLT> PLT> PLT> [6]xronos>
-> TIMEDEL=6.2500000000E-02 for ad55000030g300170h.evt
** XSELECT V1.3 **
!> Enter session name >[xsel] xsel
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS PHA_BINS
1 GAL_RIDG PH HIGH 09/04/97 21:03:10 0.78E+04 5519 1024
EXTRACTOR vers 2.0 11 Apr 1997.
Doing file: /data/data16/seq_proc/55000030.005/ad55000030g300170h.evt
Total Good Bad: Region Time Phase Cut
5519 5519 0 0 0 0
Writing events file
5519 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
5519 5519 0 0 0 0
in 7788.22 seconds
Command not found; type ? for a command listing
!xsel:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!xsel:ASCA > set datadir .
Setting data directory to /data/data16/seq_proc/55000030.005/
Setting mkf directory to /data/data16/seq_proc/55000030.005/
!xsel:ASCA > read events ad55000030g300170h.evt
Got new instrument: GIS3
Setting: IMAGE binning = 1
WMAP binning = 1
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 1023
Got the minimum time resolution of the read data: 0.62500E-01
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data16/seq_proc/55000030.005/
HK Directory is: /data/data16/seq_proc/55000030.005/
!xsel:ASCA-GIS3-PH > filter region ad55000030g325670_0.reg
!xsel:ASCA-GIS3-PH > extract events
!xsel:ASCA-GIS3-PH > save events outfile=events.tmp use_events=yes
Wrote events list to file events.tmp
Changing Data directory from:
/data/data16/seq_proc/55000030.005/
to the current working directory.
!xsel:ASCA-GIS3-PH > exit save_session=no
-> Extracting ad55000030g300070_0.lc with binsize 70.5582486746708
** XSELECT V1.3 **
!> Enter session name >[xsel] xsel
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS PHA_BINS
1 GAL_RIDG PH HIGH 09/04/97 21:03:10 0.78E+04 5519 1024
EXTRACTOR vers 2.0 11 Apr 1997.
Doing file: /data/data16/seq_proc/55000030.005/events.tmp
Total Good Bad: Region Time Phase Cut
5519 5519 0 0 0 0
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
5519 5519 0 0 0 0
in 7788.22 seconds
Fits light curve has 5519 counts for 0.7086 counts/sec
Command not found; type ? for a command listing
!xsel:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!xsel:ASCA > set datadir .
Setting data directory to /data/data16/seq_proc/55000030.005/
Setting mkf directory to /data/data16/seq_proc/55000030.005/
!xsel:ASCA > read events events.tmp
Got new instrument: GIS3
Setting: IMAGE binning = 1
WMAP binning = 1
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 1023
Got the minimum time resolution of the read data: 0.62500E-01
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data16/seq_proc/55000030.005/
HK Directory is: /data/data16/seq_proc/55000030.005/
!xsel:ASCA-GIS3-PH > set binsize 70.5582486746708
!xsel:ASCA-GIS3-PH > extract curve exposure=0.5
!xsel:ASCA-GIS3-PH > save curve ad55000030g300070_0.lc
Wrote FITS light curve to file ad55000030g300070_0.lc
!xsel:ASCA-GIS3-PH > exit save_session=no
-> Plotting light curve ad55000030g300070_0_lc.ps
Type "help" for information
[1]xronos> Current User Interface is ; command driven
[2]xronos> Enter up to 50 input filenames and options for series 1 (or rtn)
Ser. A filename 1 +options[.rbf]=> ad55000030g300070_0.lc
Selected FITS extensions: 1 - RATE TABLE;
Source ............ GAL_RIDGE_7_N4 Start Time (d) .... 10547 21:03:10.245
FITS Extension .... 1 - `RATE ` Stop Time (d) ..... 10548 05:59:10.245
No. of Rows ....... 112 Bin Time (s) ...... 70.56
Right Ascension ... 2.7568E+02 Internal time sys.. Converted to TJD
Declination ....... -1.3702E+01 Experiment ........ ASCA GIS3
Corrections applied: Vignetting - No ; Deadtime - No ; Bkgd - No ; Clock - No
Selected Columns: 1 - Time; 2 - Y-axis; 3 - Y-error;
File contains binned data.
Ser. A filename 2 +options[.rbf]=>
Enter up to 50 input filenames and options for series 2 (or rtn)
Ser. B filename 1 +options[.rbf]=>
Enter up to 50 input filenames and options for series 3 (or rtn)
Ser. C filename 1 +options[.rbf]=>
[3]xronos>
Maximum of 1 Intvs. with 456 Newbins of 70.5583 (s)
Intv 1 Start10547 21: 3:45
Ser.1 Avg 0.7100 Chisq 116.4 Var 0.1114E-01 Newbs. 112
Min 0.4229 Max 0.9779 expVar 0.1072E-01 Bins 112
Results from Statistical Analysis
Newbin Integration Time (s).. 70.558
Interval Duration (s)........ 32104.
No. of Newbins .............. 112
Average (c/s) ............... 0.71001 +/- 0.98E-02
Standard Deviation (c/s)..... 0.10554
Minimum (c/s)................ 0.42295
Maximum (c/s)................ 0.97792
Variance ((c/s)**2).......... 0.11139E-01 +/- 0.15E-02
Expected Variance ((c/s)**2). 0.10718E-01 +/- 0.14E-02
Third Moment ((c/s)**3)...... 0.44999E-03
Average Deviation (c/s)...... 0.83235E-01
Skewness..................... 0.38277 +/- 0.23
Kurtosis..................... 0.63783E-01 +/- 0.46
RMS fractional variation....< 0.93597E-01 (3 sigma)
Chi-Square................... 116.40 dof 111
Chi-Square Prob of constancy. 0.34404 (0 means < 1.e-38)
Kolm.-Smir. Prob of constancy 0.20351E-02 (0 means < 1.e-38)
[4]xronos> [5]xronos>
Maximum of 1 Intvs. with 456 Newbins of 70.5583 (s)
Intv 1 Start10547 21: 3:45
Ser.1 Avg 0.7100 Chisq 116.4 Var 0.1114E-01 Newbs. 112
Min 0.4229 Max 0.9779 expVar 0.1072E-01 Bins 112
Light curve ready !
Frme 1 Written to output file : xronos.qlc1
PLT> PLT> PLT> [6]xronos>
-> Merging GTIs from the following files:ad55000030g200170h.evt[2]-> Making L1 light curve of ft970409_2051_0625G2HK.fits with irate=HIGH
ghkcurve: ALLGTI found in input HK file, will be applied to data. ghkcurve: 17357 output records from 17386 good input G2_L1 records.-> Making L1 light curve of ft970409_2051_0625G2HK.fits with irate=HI+MED
ghkcurve: ALLGTI found in input HK file, will be applied to data. ghkcurve: 7184 output records from 17386 good input G2_L1 records.-> Merging GTIs from the following files:
ad55000030g300170h.evt[2]-> Making L1 light curve of ft970409_2051_0625G3HK.fits with irate=HIGH
ghkcurve: ALLGTI found in input HK file, will be applied to data. ghkcurve: 16685 output records from 16713 good input G3_L1 records.-> Making L1 light curve of ft970409_2051_0625G3HK.fits with irate=HI+MED
ghkcurve: ALLGTI found in input HK file, will be applied to data. ghkcurve: 7100 output records from 16713 good input G3_L1 records.
** XSELECT V1.3 **
!> Enter session name >[xsel] xsel
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS PHA_BINS
1 GAL_RIDG PH HIGH 09/04/97 21:03:10 0.78E+04 5406 1024
EXTRACTOR vers 2.0 11 Apr 1997.
Doing file: /data/data16/seq_proc/55000030.005/ad55000030g200170h.evt
Total Good Bad: Region Time Phase Cut
5406 5406 0 0 0 0
Writing events file
5406 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
5406 5406 0 0 0 0
in 7796.22 seconds
Command not found; type ? for a command listing
!xsel:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!xsel:ASCA > set datadir .
Setting data directory to /data/data16/seq_proc/55000030.005/
Setting mkf directory to /data/data16/seq_proc/55000030.005/
!xsel:ASCA > read events ad55000030g200170h.evt
Got new instrument: GIS2
Setting: IMAGE binning = 1
WMAP binning = 1
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 1023
Got the minimum time resolution of the read data: 0.62500E-01
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data16/seq_proc/55000030.005/
HK Directory is: /data/data16/seq_proc/55000030.005/
!xsel:ASCA-GIS2-PH > filter region ad55000030g225670_0.reg
!xsel:ASCA-GIS2-PH > extract events
!xsel:ASCA-GIS2-PH > save events outfile=ad55000030g200170h_0.ulc use_events=yes
Wrote events list to file ad55000030g200170h_0.ulc
Changing Data directory from:
/data/data16/seq_proc/55000030.005/
to the current working directory.
!xsel:ASCA-GIS2-PH > exit save_session=no
-> Extracting unbinned light curve ad55000030g300170h_0.ulc
** XSELECT V1.3 **
!> Enter session name >[xsel] xsel
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS PHA_BINS
1 GAL_RIDG PH HIGH 09/04/97 21:03:10 0.78E+04 5519 1024
EXTRACTOR vers 2.0 11 Apr 1997.
Doing file: /data/data16/seq_proc/55000030.005/ad55000030g300170h.evt
Total Good Bad: Region Time Phase Cut
5519 5519 0 0 0 0
Writing events file
5519 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
5519 5519 0 0 0 0
in 7788.22 seconds
Command not found; type ? for a command listing
!xsel:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!xsel:ASCA > set datadir .
Setting data directory to /data/data16/seq_proc/55000030.005/
Setting mkf directory to /data/data16/seq_proc/55000030.005/
!xsel:ASCA > read events ad55000030g300170h.evt
Got new instrument: GIS3
Setting: IMAGE binning = 1
WMAP binning = 1
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 1023
Got the minimum time resolution of the read data: 0.62500E-01
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data16/seq_proc/55000030.005/
HK Directory is: /data/data16/seq_proc/55000030.005/
!xsel:ASCA-GIS3-PH > filter region ad55000030g325670_0.reg
!xsel:ASCA-GIS3-PH > extract events
!xsel:ASCA-GIS3-PH > save events outfile=ad55000030g300170h_0.ulc use_events=yes
Wrote events list to file ad55000030g300170h_0.ulc
Changing Data directory from:
/data/data16/seq_proc/55000030.005/
to the current working directory.
!xsel:ASCA-GIS3-PH > exit save_session=no
-> Extracting unbinned light curve ad55000030s000102h_0.ulc
** XSELECT V1.3 **
!> Enter session name >[xsel] xsel
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS S0CCDPOW
1 GAL_RIDG BRIGHT HIGH 09/04/97 21:55:34 0.41E+03 137 1111
EXTRACTOR vers 2.0 11 Apr 1997.
Doing file: /data/data16/seq_proc/55000030.005/ad55000030s000102h.evt
Total Good Bad: Region Time Phase Cut
137 137 0 0 0 0
Writing events file
137 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
137 137 0 0 0 0
in 414.24 seconds
Command not found; type ? for a command listing
!xsel:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!xsel:ASCA > set datadir .
Setting data directory to /data/data16/seq_proc/55000030.005/
Setting mkf directory to /data/data16/seq_proc/55000030.005/
!xsel:ASCA > read events ad55000030s000102h.evt
Got new instrument: SIS0
Setting: IMAGE binning = 4
WMAP binning = 8
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 2047
Got the minimum time resolution of the read data: 16.000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data16/seq_proc/55000030.005/
HK Directory is: /data/data16/seq_proc/55000030.005/
!xsel:ASCA-SIS0-BRIGHT > filter region ad55000030s032002_0.reg
!xsel:ASCA-SIS0-BRIGHT > extract events
!xsel:ASCA-SIS0-BRIGHT > save events outfile=ad55000030s000102h_0.ulc use_events=yes
Wrote events list to file ad55000030s000102h_0.ulc
Changing Data directory from:
/data/data16/seq_proc/55000030.005/
to the current working directory.
!xsel:ASCA-SIS0-BRIGHT > exit save_session=no
-> Extracting unbinned light curve ad55000030s000112h_0.ulc
** XSELECT V1.3 **
!> Enter session name >[xsel] xsel
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS S0CCDPOW
1 GAL_RIDG BRIGHT2 HIGH 09/04/97 21:55:34 0.41E+03 151 1111
EXTRACTOR vers 2.0 11 Apr 1997.
Doing file: /data/data16/seq_proc/55000030.005/ad55000030s000112h.evt
Total Good Bad: Region Time Phase Cut
151 151 0 0 0 0
Writing events file
151 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
151 151 0 0 0 0
in 414.24 seconds
Command not found; type ? for a command listing
!xsel:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!xsel:ASCA > set datadir .
Setting data directory to /data/data16/seq_proc/55000030.005/
Setting mkf directory to /data/data16/seq_proc/55000030.005/
!xsel:ASCA > read events ad55000030s000112h.evt
Got new instrument: SIS0
Setting: IMAGE binning = 4
WMAP binning = 8
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 4095
Got the minimum time resolution of the read data: 16.000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data16/seq_proc/55000030.005/
HK Directory is: /data/data16/seq_proc/55000030.005/
!xsel:ASCA-SIS0-BRIGHT2 > filter region ad55000030s032002_0.reg
!xsel:ASCA-SIS0-BRIGHT2 > extract events
!xsel:ASCA-SIS0-BRIGHT2 > save events outfile=ad55000030s000112h_0.ulc use_events=yes
Wrote events list to file ad55000030s000112h_0.ulc
Changing Data directory from:
/data/data16/seq_proc/55000030.005/
to the current working directory.
!xsel:ASCA-SIS0-BRIGHT2 > exit save_session=no
-> Extracting unbinned light curve ad55000030s000202h_0.ulc
** XSELECT V1.3 **
!> Enter session name >[xsel] xsel
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS S0CCDPOW
1 GAL_RIDG BRIGHT HIGH 09/04/97 21:02:58 0.65E+04 1022 1111
EXTRACTOR vers 2.0 11 Apr 1997.
Doing file: /data/data16/seq_proc/55000030.005/ad55000030s000202h.evt
Total Good Bad: Region Time Phase Cut
1022 1022 0 0 0 0
Writing events file
1022 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
1022 1022 0 0 0 0
in 6489.46 seconds
Command not found; type ? for a command listing
!xsel:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!xsel:ASCA > set datadir .
Setting data directory to /data/data16/seq_proc/55000030.005/
Setting mkf directory to /data/data16/seq_proc/55000030.005/
!xsel:ASCA > read events ad55000030s000202h.evt
Got new instrument: SIS0
Setting: IMAGE binning = 4
WMAP binning = 8
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 2047
Got the minimum time resolution of the read data: 16.000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data16/seq_proc/55000030.005/
HK Directory is: /data/data16/seq_proc/55000030.005/
!xsel:ASCA-SIS0-BRIGHT > filter region ad55000030s032002_0.reg
!xsel:ASCA-SIS0-BRIGHT > extract events
!xsel:ASCA-SIS0-BRIGHT > save events outfile=ad55000030s000202h_0.ulc use_events=yes
Wrote events list to file ad55000030s000202h_0.ulc
Changing Data directory from:
/data/data16/seq_proc/55000030.005/
to the current working directory.
!xsel:ASCA-SIS0-BRIGHT > exit save_session=no
-> Extracting unbinned light curve ad55000030s000212h_0.ulc
** XSELECT V1.3 **
!> Enter session name >[xsel] xsel
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS S0CCDPOW
1 GAL_RIDG BRIGHT2 HIGH 09/04/97 21:02:58 0.65E+04 1464 1111
EXTRACTOR vers 2.0 11 Apr 1997.
Doing file: /data/data16/seq_proc/55000030.005/ad55000030s000212h.evt
Total Good Bad: Region Time Phase Cut
1464 1464 0 0 0 0
Writing events file
1464 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
1464 1464 0 0 0 0
in 6489.46 seconds
Command not found; type ? for a command listing
!xsel:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!xsel:ASCA > set datadir .
Setting data directory to /data/data16/seq_proc/55000030.005/
Setting mkf directory to /data/data16/seq_proc/55000030.005/
!xsel:ASCA > read events ad55000030s000212h.evt
Got new instrument: SIS0
Setting: IMAGE binning = 4
WMAP binning = 8
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 4095
Got the minimum time resolution of the read data: 16.000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data16/seq_proc/55000030.005/
HK Directory is: /data/data16/seq_proc/55000030.005/
!xsel:ASCA-SIS0-BRIGHT2 > filter region ad55000030s032002_0.reg
!xsel:ASCA-SIS0-BRIGHT2 > extract events
!xsel:ASCA-SIS0-BRIGHT2 > save events outfile=ad55000030s000212h_0.ulc use_events=yes
Wrote events list to file ad55000030s000212h_0.ulc
Changing Data directory from:
/data/data16/seq_proc/55000030.005/
to the current working directory.
!xsel:ASCA-SIS0-BRIGHT2 > exit save_session=no
-> Extracting unbinned light curve ad55000030s000302m_0.ulc
** XSELECT V1.3 **
!> Enter session name >[xsel] xsel
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS S0CCDPOW
1 GAL_RIDG BRIGHT MEDIUM 09/04/97 20:51:26 0.80E+02 77 1111
EXTRACTOR vers 2.0 11 Apr 1997.
Doing file: /data/data16/seq_proc/55000030.005/ad55000030s000302m.evt
Total Good Bad: Region Time Phase Cut
77 77 0 0 0 0
Writing events file
77 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
77 77 0 0 0 0
in 80.00 seconds
Command not found; type ? for a command listing
!xsel:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!xsel:ASCA > set datadir .
Setting data directory to /data/data16/seq_proc/55000030.005/
Setting mkf directory to /data/data16/seq_proc/55000030.005/
!xsel:ASCA > read events ad55000030s000302m.evt
Got new instrument: SIS0
Setting: IMAGE binning = 4
WMAP binning = 8
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 2047
Got the minimum time resolution of the read data: 16.000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data16/seq_proc/55000030.005/
HK Directory is: /data/data16/seq_proc/55000030.005/
!xsel:ASCA-SIS0-BRIGHT > filter region ad55000030s032002_0.reg
!xsel:ASCA-SIS0-BRIGHT > extract events
!xsel:ASCA-SIS0-BRIGHT > save events outfile=ad55000030s000302m_0.ulc use_events=yes
Wrote events list to file ad55000030s000302m_0.ulc
Changing Data directory from:
/data/data16/seq_proc/55000030.005/
to the current working directory.
!xsel:ASCA-SIS0-BRIGHT > exit save_session=no
-> Extracting unbinned light curve ad55000030s100102h_0.ulc
** XSELECT V1.3 **
!> Enter session name >[xsel] xsel
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS S1CCDPOW
1 GAL_RIDG BRIGHT HIGH 09/04/97 21:02:58 0.70E+04 740 1111
EXTRACTOR vers 2.0 11 Apr 1997.
Doing file: /data/data16/seq_proc/55000030.005/ad55000030s100102h.evt
Total Good Bad: Region Time Phase Cut
740 740 0 0 0 0
Writing events file
740 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
740 740 0 0 0 0
in 7007.70 seconds
Command not found; type ? for a command listing
!xsel:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!xsel:ASCA > set datadir .
Setting data directory to /data/data16/seq_proc/55000030.005/
Setting mkf directory to /data/data16/seq_proc/55000030.005/
!xsel:ASCA > read events ad55000030s100102h.evt
Got new instrument: SIS1
Setting: IMAGE binning = 4
WMAP binning = 8
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 2047
Got the minimum time resolution of the read data: 16.000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data16/seq_proc/55000030.005/
HK Directory is: /data/data16/seq_proc/55000030.005/
!xsel:ASCA-SIS1-BRIGHT > filter region ad55000030s132002_0.reg
!xsel:ASCA-SIS1-BRIGHT > extract events
!xsel:ASCA-SIS1-BRIGHT > save events outfile=ad55000030s100102h_0.ulc use_events=yes
Wrote events list to file ad55000030s100102h_0.ulc
Changing Data directory from:
/data/data16/seq_proc/55000030.005/
to the current working directory.
!xsel:ASCA-SIS1-BRIGHT > exit save_session=no
-> Extracting unbinned light curve ad55000030s100112h_0.ulc
** XSELECT V1.3 **
!> Enter session name >[xsel] xsel
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS S1CCDPOW
1 GAL_RIDG BRIGHT2 HIGH 09/04/97 21:02:58 0.70E+04 1395 1111
EXTRACTOR vers 2.0 11 Apr 1997.
Doing file: /data/data16/seq_proc/55000030.005/ad55000030s100112h.evt
Total Good Bad: Region Time Phase Cut
1395 1395 0 0 0 0
Writing events file
1395 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
1395 1395 0 0 0 0
in 7007.70 seconds
Command not found; type ? for a command listing
!xsel:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!xsel:ASCA > set datadir .
Setting data directory to /data/data16/seq_proc/55000030.005/
Setting mkf directory to /data/data16/seq_proc/55000030.005/
!xsel:ASCA > read events ad55000030s100112h.evt
Got new instrument: SIS1
Setting: IMAGE binning = 4
WMAP binning = 8
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 4095
Got the minimum time resolution of the read data: 16.000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data16/seq_proc/55000030.005/
HK Directory is: /data/data16/seq_proc/55000030.005/
!xsel:ASCA-SIS1-BRIGHT2 > filter region ad55000030s132002_0.reg
!xsel:ASCA-SIS1-BRIGHT2 > extract events
!xsel:ASCA-SIS1-BRIGHT2 > save events outfile=ad55000030s100112h_0.ulc use_events=yes
Wrote events list to file ad55000030s100112h_0.ulc
Changing Data directory from:
/data/data16/seq_proc/55000030.005/
to the current working directory.
!xsel:ASCA-SIS1-BRIGHT2 > exit save_session=no
-> Extracting unbinned light curve ad55000030s100202h_0.ulc
** XSELECT V1.3 **
!> Enter session name >[xsel] xsel
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS S1CCDPOW
1 GAL_RIDG BRIGHT HIGH 10/04/97 02:43:42 0.16E+02 44 1111
EXTRACTOR vers 2.0 11 Apr 1997.
Doing file: /data/data16/seq_proc/55000030.005/ad55000030s100202h.evt
Total Good Bad: Region Time Phase Cut
44 44 0 0 0 0
Writing events file
44 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
44 44 0 0 0 0
in 16.06 seconds
Command not found; type ? for a command listing
!xsel:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!xsel:ASCA > set datadir .
Setting data directory to /data/data16/seq_proc/55000030.005/
Setting mkf directory to /data/data16/seq_proc/55000030.005/
!xsel:ASCA > read events ad55000030s100202h.evt
Got new instrument: SIS1
Setting: IMAGE binning = 4
WMAP binning = 8
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 2047
Got the minimum time resolution of the read data: 16.000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data16/seq_proc/55000030.005/
HK Directory is: /data/data16/seq_proc/55000030.005/
!xsel:ASCA-SIS1-BRIGHT > filter region ad55000030s132002_0.reg
!xsel:ASCA-SIS1-BRIGHT > extract events
!xsel:ASCA-SIS1-BRIGHT > save events outfile=ad55000030s100202h_0.ulc use_events=yes
Wrote events list to file ad55000030s100202h_0.ulc
Changing Data directory from:
/data/data16/seq_proc/55000030.005/
to the current working directory.
!xsel:ASCA-SIS1-BRIGHT > exit save_session=no
-> Extracting unbinned light curve ad55000030s100212h_0.ulc
** XSELECT V1.3 **
!> Enter session name >[xsel] xsel
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS S1CCDPOW
1 GAL_RIDG BRIGHT2 HIGH 10/04/97 02:43:42 0.16E+02 109 1111
EXTRACTOR vers 2.0 11 Apr 1997.
Doing file: /data/data16/seq_proc/55000030.005/ad55000030s100212h.evt
Total Good Bad: Region Time Phase Cut
109 109 0 0 0 0
Writing events file
109 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
109 109 0 0 0 0
in 16.06 seconds
Command not found; type ? for a command listing
!xsel:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!xsel:ASCA > set datadir .
Setting data directory to /data/data16/seq_proc/55000030.005/
Setting mkf directory to /data/data16/seq_proc/55000030.005/
!xsel:ASCA > read events ad55000030s100212h.evt
Got new instrument: SIS1
Setting: IMAGE binning = 4
WMAP binning = 8
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 4095
Got the minimum time resolution of the read data: 16.000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data16/seq_proc/55000030.005/
HK Directory is: /data/data16/seq_proc/55000030.005/
!xsel:ASCA-SIS1-BRIGHT2 > filter region ad55000030s132002_0.reg
!xsel:ASCA-SIS1-BRIGHT2 > extract events
!xsel:ASCA-SIS1-BRIGHT2 > save events outfile=ad55000030s100212h_0.ulc use_events=yes
Wrote events list to file ad55000030s100212h_0.ulc
Changing Data directory from:
/data/data16/seq_proc/55000030.005/
to the current working directory.
!xsel:ASCA-SIS1-BRIGHT2 > exit save_session=no
-> Extracting unbinned light curve ad55000030s100302m_0.ulc
** XSELECT V1.3 **
!> Enter session name >[xsel] xsel
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS S1CCDPOW
1 GAL_RIDG BRIGHT MEDIUM 09/04/97 20:51:26 0.80E+02 57 1111
EXTRACTOR vers 2.0 11 Apr 1997.
Doing file: /data/data16/seq_proc/55000030.005/ad55000030s100302m.evt
Total Good Bad: Region Time Phase Cut
57 57 0 0 0 0
Writing events file
57 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
57 57 0 0 0 0
in 80.00 seconds
Command not found; type ? for a command listing
!xsel:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!xsel:ASCA > set datadir .
Setting data directory to /data/data16/seq_proc/55000030.005/
Setting mkf directory to /data/data16/seq_proc/55000030.005/
!xsel:ASCA > read events ad55000030s100302m.evt
Got new instrument: SIS1
Setting: IMAGE binning = 4
WMAP binning = 8
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 2047
Got the minimum time resolution of the read data: 16.000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data16/seq_proc/55000030.005/
HK Directory is: /data/data16/seq_proc/55000030.005/
!xsel:ASCA-SIS1-BRIGHT > filter region ad55000030s132002_0.reg
!xsel:ASCA-SIS1-BRIGHT > extract events
!xsel:ASCA-SIS1-BRIGHT > save events outfile=ad55000030s100302m_0.ulc use_events=yes
Wrote events list to file ad55000030s100302m_0.ulc
Changing Data directory from:
/data/data16/seq_proc/55000030.005/
to the current working directory.
!xsel:ASCA-SIS1-BRIGHT > exit save_session=no
*** tlmFrm Version 1.1 (1997-08-25) ***
total number of superframes: 11628
frame data: 134790086.192223 ---> 134790230.191783
S1, C2, 4 ccd mode; Output File = fr970409_2051.0625_s1c2m4a.fits
frame data: 134790250.191722 ---> 134790394.191282
S1, C3, 4 ccd mode; Output File = fr970409_2051.0625_s1c3m4a.fits
frame data: 134790414.191221 ---> 134790558.190783
S1, C0, 4 ccd mode; Output File = fr970409_2051.0625_s1c0m4a.fits
frame data: 134790578.190722 ---> 134790722.190283
S1, C1, 4 ccd mode; Output File = fr970409_2051.0625_s1c1m4a.fits
frame data: 134795818.17458 ---> 134795962.174141
S0, C0, 4 ccd mode; Output File = fr970409_2051.0625_s0c0m4a.fits
frame data: 134795982.17408 ---> 134796126.173642
S0, C1, 4 ccd mode; Output File = fr970409_2051.0625_s0c1m4a.fits
frame data: 134796146.173581 ---> 134796290.173144
S0, C2, 4 ccd mode; Output File = fr970409_2051.0625_s0c2m4a.fits
frame data: 134796310.173084 ---> 134796454.172646
S0, C3, 4 ccd mode; Output File = fr970409_2051.0625_s0c3m4a.fits
frame data: 134801542.15701 ---> 134801686.156572
S1, C2, 4 ccd mode; Output File = fr970409_2051.0625_s1c2m4b.fits
frame data: 134801706.156511 ---> 134801850.156073
S1, C3, 4 ccd mode; Output File = fr970409_2051.0625_s1c3m4b.fits
frame data: 134801870.156012 ---> 134802014.155574
S1, C0, 4 ccd mode; Output File = fr970409_2051.0625_s1c0m4b.fits
frame data: 134802034.155513 ---> 134802178.155075
S1, C1, 4 ccd mode; Output File = fr970409_2051.0625_s1c1m4b.fits
Total of 12 sets of frame data are extracted.
-> Processing fr970409_2051.0625_s0c0m4a.fitsDark upper (ADU) : 40 Dark lower (ADU) : -40 Input frame data : fr970409_2051.0625_s0c0m4a.fits Output zero level image : rdd.tmp Bias level = 326-> Adding keywords to header of fr970409_2051.0625_s0c0m4a.fits
Dark upper (ADU) : 40 Dark lower (ADU) : -40 Input frame data : fr970409_2051.0625_s0c1m4a.fits Output zero level image : rdd.tmp Bias level = 290-> Adding keywords to header of fr970409_2051.0625_s0c1m4a.fits
Dark upper (ADU) : 40 Dark lower (ADU) : -40 Input frame data : fr970409_2051.0625_s0c2m4a.fits Output zero level image : rdd.tmp Bias level = 321-> Adding keywords to header of fr970409_2051.0625_s0c2m4a.fits
Dark upper (ADU) : 40 Dark lower (ADU) : -40 Input frame data : fr970409_2051.0625_s0c3m4a.fits Output zero level image : rdd.tmp Bias level = 299-> Adding keywords to header of fr970409_2051.0625_s0c3m4a.fits
Dark upper (ADU) : 40 Dark lower (ADU) : -40 Input frame data : fr970409_2051.0625_s1c0m4a.fits Output zero level image : rdd.tmp Bias level = 221-> Adding keywords to header of fr970409_2051.0625_s1c0m4a.fits
Dark upper (ADU) : 40 Dark lower (ADU) : -40 Input frame data : fr970409_2051.0625_s1c0m4b.fits Output zero level image : rdd.tmp Bias level = 221-> Adding keywords to header of fr970409_2051.0625_s1c0m4b.fits
Dark upper (ADU) : 40 Dark lower (ADU) : -40 Input frame data : fr970409_2051.0625_s1c1m4a.fits Output zero level image : rdd.tmp Bias level = 188-> Adding keywords to header of fr970409_2051.0625_s1c1m4a.fits
Dark upper (ADU) : 40 Dark lower (ADU) : -40 Input frame data : fr970409_2051.0625_s1c1m4b.fits Output zero level image : rdd.tmp Bias level = 189-> Adding keywords to header of fr970409_2051.0625_s1c1m4b.fits
Dark upper (ADU) : 40 Dark lower (ADU) : -40 Input frame data : fr970409_2051.0625_s1c2m4a.fits Output zero level image : rdd.tmp Bias level = 180-> Adding keywords to header of fr970409_2051.0625_s1c2m4a.fits
Dark upper (ADU) : 40 Dark lower (ADU) : -40 Input frame data : fr970409_2051.0625_s1c2m4b.fits Output zero level image : rdd.tmp Bias level = 180-> Adding keywords to header of fr970409_2051.0625_s1c2m4b.fits
Dark upper (ADU) : 40 Dark lower (ADU) : -40 Input frame data : fr970409_2051.0625_s1c3m4a.fits Output zero level image : rdd.tmp Bias level = 217-> Adding keywords to header of fr970409_2051.0625_s1c3m4a.fits
Dark upper (ADU) : 40 Dark lower (ADU) : -40 Input frame data : fr970409_2051.0625_s1c3m4b.fits Output zero level image : rdd.tmp Bias level = 217-> Adding keywords to header of fr970409_2051.0625_s1c3m4b.fits
1 ad55000030g200170h.unf 19577-> Fetching GIS2_CALSRC256.2
** XSELECT V1.3 **
!> Enter session name >[xsel] xsel
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS PHA_BINS
1 GAL_RIDG PH HIGH 09/04/97 21:03:10 0.19E+05 19577 1024
EXTRACTOR vers 2.0 11 Apr 1997.
Getting FITS WCS Keywords
Doing file: /data/data16/seq_proc/55000030.005/ad55000030g200170h.unf
Total Good Bad: Region Time Phase Cut
19577 3216 16361 0 0 0
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
19577 3216 16361 0 0 0
in 18527.94 seconds
Spectrum has 3216 counts for 0.1736 counts/sec
-------------------------
MANDATORY KEYWORDS/VALUES
-------------------------
--------------------------------------------------------------------
--------------------------------------------------------------------
EXTNAME - SPECTRUM Name of this BINTABLE
TELESCOP - ASCA Mission/Satellite name
INSTRUME - GIS2 Instrument/Detector
FILTER - Instrument filter in use
EXPOSURE - 18528. Integration time (in secs) of PHA data
AREASCAL - 1.0000 Area scaling factor
BACKSCAL - 3.57971E-02 Background scaling factor
BACKFILE - NONE Associated background file
CORRSCAL - 1.0000 Correlation scaling factor
CORRFILE - none Associated correlation file
RESPFILE - NONE Associated redistribution matrix file
ANCRFILE - none Associated ancillary response file
XFLT0001 - none XSPEC selection filter
POISSERR - TRUE Whether Poissonian errors apply
CHANTYPE - PI Whether channels have been corrected
TLMIN1 - 0 First legal Detector channel
DETCHANS - 1024 No. of legal detector channels
NCHAN - 1024 No. of detector channels in dataset
PHAVERSN - 1992a OGIP FITS version number
STAT_ERR - FALSE Statistical Error
SYS_ERR - TRUE Fractional Systematic Error
QUALITY - TRUE Quality Flag
GROUPING - FALSE Grouping Flag
--------------------------------------------------------------------
--------------------------------------------------------------------
...
... --------
... GROUPING
... --------
... ---------------------------------------------
... Channel Grouping (Channel-Channel) :
... ---------------------------------------------
...
...... exiting, changes written to file : ad55000030g220170.cal
Command not found; type ? for a command listing
!xsel:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!xsel:ASCA > set datadir .
Setting data directory to /data/data16/seq_proc/55000030.005/
Setting mkf directory to /data/data16/seq_proc/55000030.005/
!xsel:ASCA > read events ad55000030g200170h.unf
Got new instrument: GIS2
Setting: IMAGE binning = 1
WMAP binning = 1
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 1023
Got the minimum time resolution of the read data: 0.62500E-01
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data16/seq_proc/55000030.005/
HK Directory is: /data/data16/seq_proc/55000030.005/
!xsel:ASCA-GIS2-PH > filter region GIS2_CALSRC256.2
!xsel:ASCA-GIS2-PH > extract spectrum
!xsel:ASCA-GIS2-PH > save spectrum ad55000030g220170.cal group=yes
Wrote spectrum to ad55000030g220170.cal
!xsel:ASCA-GIS2-PH > exit save_session=no
-> gis2v4_0.rmf already present in current directory
XSPEC 9.01 21:20:50 25-May-98
Plot device not set, use "cpd" to set it
Type "help" or "?" for further information
!XSPEC> query yes
Querying disabled - assuming answer is yes
!XSPEC> data ad55000030g220170.cal
Net count rate (cts/s) for file 1 0.1736 +/- 3.0707E-03
1 data set is in use
!XSPEC> ignore bad
!XSPEC> ignore **-4.0
!XSPEC> ignore 8.0-**
!XSPEC> model const/b + gauss/b + gauss/b
Background components must be from the additive model list
mo = constant[1] ) + gaussian/b[2] + gaussian/b[3]
Input parameter value, delta, min, bot, top, and max values for ...
Mod parameter 1 of component 1 constant factor
1.000 1.0000E-02 0. 0. 1.0000E+10 1.0000E+10
!
Mod parameter 2 of component 2 gaussian LineE
6.500 5.0000E-02 0. 0. 1.0000E+06 1.0000E+06
! 5.9
Mod parameter 3 of component 2 gaussian Sigma
0.1000 5.0000E-02 0. 0. 10.00 20.00
! 0.0
Mod parameter 4 of component 2 gaussian norm
1.000 1.0000E-02 0. 0. 1.0000E+24 1.0000E+24
!
Mod parameter 5 of component 3 gaussian LineE
6.500 5.0000E-02 0. 0. 1.0000E+06 1.0000E+06
! 6.5
Mod parameter 6 of component 3 gaussian Sigma
0.1000 5.0000E-02 0. 0. 10.00 20.00
! 0.0
Mod parameter 7 of component 3 gaussian norm
1.000 1.0000E-02 0. 0. 1.0000E+24 1.0000E+24
!
---------------------------------------------------------------------------
---------------------------------------------------------------------------
mo = constant[1] ) + gaussian/b[2] + gaussian/b[3]
Model Fit Model Component Parameter Value
par par comp
1 1 1 constant factor 1.00000 +/- 0.
2 2 2 gaussian/b LineE 5.90000 +/- 0.
3 3 2 gaussian/b Sigma 0. +/- 0.
4 4 2 gaussian/b norm 1.00000 +/- 0.
5 5 3 gaussian/b LineE 6.50000 +/- 0.
6 6 3 gaussian/b Sigma 0. +/- 0.
7 7 3 gaussian/b norm 1.00000 +/- 0.
---------------------------------------------------------------------------
---------------------------------------------------------------------------
7 variable fit parameters
Chi-Squared = 8.0820E+05 using 84 PHA bins.
Reduced chi-squared = 1.0496E+04
!XSPEC> newpar 5 = 2 1.101005
6 variable fit parameters
Chi-Squared = 8.0083E+05 using 84 PHA bins.
Reduced chi-squared = 1.0267E+04
!XSPEC> newpar 6 = 3 1.049288
5 variable fit parameters
Chi-Squared = 8.0083E+05 using 84 PHA bins.
Reduced chi-squared = 1.0137E+04
!XSPEC> renorm
Chi-Squared = 933.8 using 84 PHA bins.
Reduced chi-squared = 11.82
!XSPEC> fit
Chi-Squared Lvl Fit param # 1 2 3 4
5
Due to zero model norms
fit parameter 1 is temporarily frozen
758.93 0 1.000 5.892 9.4789E-02 4.5947E-02
4.0096E-02
Due to zero model norms
fit parameter 1 is temporarily frozen
338.79 0 1.000 5.860 0.1485 6.9651E-02
3.5311E-02
Due to zero model norms
fit parameter 1 is temporarily frozen
178.03 -1 1.000 5.904 0.1626 9.7117E-02
2.4507E-02
Due to zero model norms
fit parameter 1 is temporarily frozen
139.73 -2 1.000 5.959 0.1942 0.1125
1.4422E-02
Due to zero model norms
fit parameter 1 is temporarily frozen
139.34 -3 1.000 5.958 0.1888 0.1125
1.4655E-02
Due to zero model norms
fit parameter 1 is temporarily frozen
139.34 -4 1.000 5.958 0.1888 0.1126
1.4591E-02
---------------------------------------------------------------------------
---------------------------------------------------------------------------
mo = constant[1] ) + gaussian/b[2] + gaussian/b[3]
Model Fit Model Component Parameter Value
par par comp
1 1 1 constant factor 1.00000 +/- -1.0000
2 2 2 gaussian/b LineE 5.95780 +/- 0.99538E-02
3 3 2 gaussian/b Sigma 0.188760 +/- 0.10624E-01
4 4 2 gaussian/b norm 0.112580 +/- 0.30519E-02
5 2 3 gaussian/b LineE 6.55957 = par 2 * 1.1010
6 3 3 gaussian/b Sigma 0.198064 = par 3 * 1.0493
7 5 3 gaussian/b norm 1.459084E-02 +/- 0.19561E-02
---------------------------------------------------------------------------
---------------------------------------------------------------------------
Chi-Squared = 139.3 using 84 PHA bins.
Reduced chi-squared = 1.764
!XSPEC> setplot energy
!XSPEC> iplot data
!PLT> label top GIS2 Calibration Source, should peak near 5.9 keV
!PLT> log x off
!PLT> rescale x 4 8
!PLT> hard /ps
!PLT> quit
!XSPEC> exit
!Do you really want to exit (y) y
XSPEC: quit
-> Calibration source ad55000030g220170.cal peaks at 5.95780 +/- 0.0099538 keV1 ad55000030g300170h.unf 18594-> Fetching GIS3_CALSRC256.2
** XSELECT V1.3 **
!> Enter session name >[xsel] xsel
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS PHA_BINS
1 GAL_RIDG PH HIGH 09/04/97 21:03:10 0.19E+05 18594 1024
EXTRACTOR vers 2.0 11 Apr 1997.
Getting FITS WCS Keywords
Doing file: /data/data16/seq_proc/55000030.005/ad55000030g300170h.unf
Total Good Bad: Region Time Phase Cut
18594 2691 15903 0 0 0
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
18594 2691 15903 0 0 0
in 18519.94 seconds
Spectrum has 2691 counts for 0.1453 counts/sec
-------------------------
MANDATORY KEYWORDS/VALUES
-------------------------
--------------------------------------------------------------------
--------------------------------------------------------------------
EXTNAME - SPECTRUM Name of this BINTABLE
TELESCOP - ASCA Mission/Satellite name
INSTRUME - GIS3 Instrument/Detector
FILTER - Instrument filter in use
EXPOSURE - 18520. Integration time (in secs) of PHA data
AREASCAL - 1.0000 Area scaling factor
BACKSCAL - 2.83356E-02 Background scaling factor
BACKFILE - NONE Associated background file
CORRSCAL - 1.0000 Correlation scaling factor
CORRFILE - none Associated correlation file
RESPFILE - NONE Associated redistribution matrix file
ANCRFILE - none Associated ancillary response file
XFLT0001 - none XSPEC selection filter
POISSERR - TRUE Whether Poissonian errors apply
CHANTYPE - PI Whether channels have been corrected
TLMIN1 - 0 First legal Detector channel
DETCHANS - 1024 No. of legal detector channels
NCHAN - 1024 No. of detector channels in dataset
PHAVERSN - 1992a OGIP FITS version number
STAT_ERR - FALSE Statistical Error
SYS_ERR - TRUE Fractional Systematic Error
QUALITY - TRUE Quality Flag
GROUPING - FALSE Grouping Flag
--------------------------------------------------------------------
--------------------------------------------------------------------
...
... --------
... GROUPING
... --------
... ---------------------------------------------
... Channel Grouping (Channel-Channel) :
... ---------------------------------------------
...
...... exiting, changes written to file : ad55000030g320170.cal
Command not found; type ? for a command listing
!xsel:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!xsel:ASCA > set datadir .
Setting data directory to /data/data16/seq_proc/55000030.005/
Setting mkf directory to /data/data16/seq_proc/55000030.005/
!xsel:ASCA > read events ad55000030g300170h.unf
Got new instrument: GIS3
Setting: IMAGE binning = 1
WMAP binning = 1
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 1023
Got the minimum time resolution of the read data: 0.62500E-01
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data16/seq_proc/55000030.005/
HK Directory is: /data/data16/seq_proc/55000030.005/
!xsel:ASCA-GIS3-PH > filter region GIS3_CALSRC256.2
!xsel:ASCA-GIS3-PH > extract spectrum
!xsel:ASCA-GIS3-PH > save spectrum ad55000030g320170.cal group=yes
Wrote spectrum to ad55000030g320170.cal
!xsel:ASCA-GIS3-PH > exit save_session=no
-> gis3v4_0.rmf already present in current directory
XSPEC 9.01 21:21:52 25-May-98
Plot device not set, use "cpd" to set it
Type "help" or "?" for further information
!XSPEC> query yes
Querying disabled - assuming answer is yes
!XSPEC> data ad55000030g320170.cal
Net count rate (cts/s) for file 1 0.1453 +/- 2.8202E-03
1 data set is in use
!XSPEC> ignore bad
!XSPEC> ignore **-4.0
!XSPEC> ignore 8.0-**
!XSPEC> model const/b + gauss/b + gauss/b
Background components must be from the additive model list
mo = constant[1] ) + gaussian/b[2] + gaussian/b[3]
Input parameter value, delta, min, bot, top, and max values for ...
Mod parameter 1 of component 1 constant factor
1.000 1.0000E-02 0. 0. 1.0000E+10 1.0000E+10
!
Mod parameter 2 of component 2 gaussian LineE
6.500 5.0000E-02 0. 0. 1.0000E+06 1.0000E+06
! 5.9
Mod parameter 3 of component 2 gaussian Sigma
0.1000 5.0000E-02 0. 0. 10.00 20.00
! 0.0
Mod parameter 4 of component 2 gaussian norm
1.000 1.0000E-02 0. 0. 1.0000E+24 1.0000E+24
!
Mod parameter 5 of component 3 gaussian LineE
6.500 5.0000E-02 0. 0. 1.0000E+06 1.0000E+06
! 6.5
Mod parameter 6 of component 3 gaussian Sigma
0.1000 5.0000E-02 0. 0. 10.00 20.00
! 0.0
Mod parameter 7 of component 3 gaussian norm
1.000 1.0000E-02 0. 0. 1.0000E+24 1.0000E+24
!
---------------------------------------------------------------------------
---------------------------------------------------------------------------
mo = constant[1] ) + gaussian/b[2] + gaussian/b[3]
Model Fit Model Component Parameter Value
par par comp
1 1 1 constant factor 1.00000 +/- 0.
2 2 2 gaussian/b LineE 5.90000 +/- 0.
3 3 2 gaussian/b Sigma 0. +/- 0.
4 4 2 gaussian/b norm 1.00000 +/- 0.
5 5 3 gaussian/b LineE 6.50000 +/- 0.
6 6 3 gaussian/b Sigma 0. +/- 0.
7 7 3 gaussian/b norm 1.00000 +/- 0.
---------------------------------------------------------------------------
---------------------------------------------------------------------------
7 variable fit parameters
Chi-Squared = 9.9772E+05 using 84 PHA bins.
Reduced chi-squared = 1.2957E+04
!XSPEC> newpar 5 = 2 1.101005
6 variable fit parameters
Chi-Squared = 9.9072E+05 using 84 PHA bins.
Reduced chi-squared = 1.2702E+04
!XSPEC> newpar 6 = 3 1.049288
5 variable fit parameters
Chi-Squared = 9.9072E+05 using 84 PHA bins.
Reduced chi-squared = 1.2541E+04
!XSPEC> renorm
Chi-Squared = 954.3 using 84 PHA bins.
Reduced chi-squared = 12.08
!XSPEC> fit
Chi-Squared Lvl Fit param # 1 2 3 4
5
Due to zero model norms
fit parameter 1 is temporarily frozen
778.92 0 1.000 5.893 8.7884E-02 3.9050E-02
3.2780E-02
Due to zero model norms
fit parameter 1 is temporarily frozen
289.71 0 1.000 5.864 0.1369 6.5384E-02
2.7779E-02
Due to zero model norms
fit parameter 1 is temporarily frozen
104.17 -1 1.000 5.905 0.1541 9.5268E-02
1.7369E-02
Due to zero model norms
fit parameter 1 is temporarily frozen
95.788 -2 1.000 5.922 0.1601 0.1025
1.3384E-02
Due to zero model norms
fit parameter 1 is temporarily frozen
95.403 -3 1.000 5.917 0.1545 0.1017
1.4173E-02
Due to zero model norms
fit parameter 1 is temporarily frozen
95.390 -4 1.000 5.918 0.1552 0.1019
1.3976E-02
Due to zero model norms
fit parameter 1 is temporarily frozen
95.384 -5 1.000 5.918 0.1549 0.1018
1.4025E-02
---------------------------------------------------------------------------
---------------------------------------------------------------------------
mo = constant[1] ) + gaussian/b[2] + gaussian/b[3]
Model Fit Model Component Parameter Value
par par comp
1 1 1 constant factor 1.00000 +/- -1.0000
2 2 2 gaussian/b LineE 5.91818 +/- 0.89571E-02
3 3 2 gaussian/b Sigma 0.154853 +/- 0.11213E-01
4 4 2 gaussian/b norm 0.101839 +/- 0.27928E-02
5 2 3 gaussian/b LineE 6.51594 = par 2 * 1.1010
6 3 3 gaussian/b Sigma 0.162486 = par 3 * 1.0493
7 5 3 gaussian/b norm 1.402534E-02 +/- 0.17009E-02
---------------------------------------------------------------------------
---------------------------------------------------------------------------
Chi-Squared = 95.38 using 84 PHA bins.
Reduced chi-squared = 1.207
!XSPEC> setplot energy
!XSPEC> iplot data
!PLT> label top GIS3 Calibration Source, should peak near 5.9 keV
!PLT> log x off
!PLT> rescale x 4 8
!PLT> hard /ps
!PLT> quit
!XSPEC> exit
!Do you really want to exit (y) y
XSPEC: quit
-> Calibration source ad55000030g320170.cal peaks at 5.91818 +/- 0.0089571 keV
** XSELECT V1.3 **
!> Enter session name >[xsel] earthevents
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS S0CCDPOW
1 GAL_RIDG BRIGHT HIGH 09/04/97 21:55:34 0.79E+04 6058 1111
EXTRACTOR vers 2.0 11 Apr 1997.
Doing file: /data/data16/seq_proc/55000030.005/ad55000030s000102h.unf
Total Good Bad: Region Time Phase Cut
6058 625 0 5433 0 0
Writing events file
625 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
6058 625 0 5433 0 0
in 143.58 seconds
Command not found; type ? for a command listing
!earthevents:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!earthevents:ASCA > set datadir .
Setting data directory to /data/data16/seq_proc/55000030.005/
Setting mkf directory to /data/data16/seq_proc/55000030.005/
!earthevents:ASCA > read events ad55000030s000102h.unf
Got new instrument: SIS0
Setting: IMAGE binning = 4
WMAP binning = 8
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 2047
Got the minimum time resolution of the read data: 16.000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data16/seq_proc/55000030.005/
HK Directory is: /data/data16/seq_proc/55000030.005/
!earthevents:ASCA-SIS0-BRIGHT > select mkf "FOV==1" data_dir=. ASCA_mkf_def_expr=ft*.mkf
!earthevents:ASCA-SIS0-BRIGHT > extract events
!earthevents:ASCA-SIS0-BRIGHT > save events outfile=event.tmp use_events=no
Wrote events list to file event.tmp
!earthevents:ASCA-SIS0-BRIGHT > exit save_session=no
-> Cleaning hot pixels from ad55000030s000102h.unf
CLEANSIS_V1.6
allocating image arrays...
PROGRAM TO MAKE AN SIS SCIENCE FILE CLEANED OF ANOMALOUS PIXELS.
* Anomalous pixels may consist of at least two populations.
1. Persistent HOT pixels are removed by comparing to the chip mean.
2. Flickering WARM pixels are removed by comparing to the cell mean.
3. In faint areas (zero bgd), flickering pixels are removed with a
cutoff threshold.
Hints:
Choose cell size and thresholds based on the expected background and the PSF.
Use the DIRTYSIS option to examine the anomalous pixel spectra.
Try a multiple pass clean:
Choose a PHA cut to optimize the S/N of the flickering pixels,
then a broad band clean.
Be suspicious of extended source cleans.
For very bright sources you may need to turn off the iteration option.
See the help page for further info (fhelp cleansis)
Poisson clean cell size : 5
Poisson probability threshold : 0.575E-05
Zero Bgd Cutoff threshold (>) : 3
Iterate : F
Dirtysis : F
Minimum PHA value (inclusive) : 0
Maximum PHA value (inclusive) : 4095
open output file: ad55000030s000102h.drk
reading data file: event.tmp
copying primary header to output file...
making chip image...
Total counts in chip images : 625
copy bad pix array...
cleaning chip # 0
Hot pixels & counts : 4 24
Flickering pixels iter, pixels & cnts : 1 40 166
cleaning chip # 1
Hot pixels & counts : 13 80
Flickering pixels iter, pixels & cnts : 1 13 47
cleaning chip # 2
Hot pixels & counts : 6 20
cleaning chip # 3
Hot pixels & counts : 13 76
Flickering pixels iter, pixels & cnts : 1 11 40
Number of pixels rejected : 100
Number of (internal) image counts : 625
Number of image cts rejected (N, %) : 453 72.4800034
By chip : 0 1 2 3
Pixels rejected : 44 26 6 24
Image counts : 273 165 46 141
Image cts rejected: 190 127 20 116
Image cts rej (%) : 69.60 76.97 43.48 82.27
filtering data...
Total counts : 273 165 46 141
Total cts rejected: 190 127 20 116
Total cts rej (%) : 69.60 76.97 43.48 82.27
Number of clean counts accepted : 172
writing history cards...
copying extensions...
writing out hot pixs...
Number of rejected pixels : 100
updating NEVENTS keywords...
closing data file...
closing clean file...
-> Extracting bright and dark Earth events from ad55000030s000112h.unf
** XSELECT V1.3 **
!> Enter session name >[xsel] earthevents
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS S0CCDPOW
1 GAL_RIDG BRIGHT2 HIGH 09/04/97 21:55:34 0.79E+04 9285 1111
EXTRACTOR vers 2.0 11 Apr 1997.
Doing file: /data/data16/seq_proc/55000030.005/ad55000030s000112h.unf
Total Good Bad: Region Time Phase Cut
9285 852 0 8433 0 0
Writing events file
852 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
9285 852 0 8433 0 0
in 143.58 seconds
Command not found; type ? for a command listing
!earthevents:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!earthevents:ASCA > set datadir .
Setting data directory to /data/data16/seq_proc/55000030.005/
Setting mkf directory to /data/data16/seq_proc/55000030.005/
!earthevents:ASCA > read events ad55000030s000112h.unf
Got new instrument: SIS0
Setting: IMAGE binning = 4
WMAP binning = 8
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 4095
Got the minimum time resolution of the read data: 16.000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data16/seq_proc/55000030.005/
HK Directory is: /data/data16/seq_proc/55000030.005/
!earthevents:ASCA-SIS0-BRIGHT2 > select mkf "FOV==1" data_dir=. ASCA_mkf_def_expr=ft*.mkf
!earthevents:ASCA-SIS0-BRIGHT2 > extract events
!earthevents:ASCA-SIS0-BRIGHT2 > save events outfile=event.tmp use_events=no
Wrote events list to file event.tmp
!earthevents:ASCA-SIS0-BRIGHT2 > exit save_session=no
-> Cleaning hot pixels from ad55000030s000112h.unf
CLEANSIS_V1.6
allocating image arrays...
PROGRAM TO MAKE AN SIS SCIENCE FILE CLEANED OF ANOMALOUS PIXELS.
* Anomalous pixels may consist of at least two populations.
1. Persistent HOT pixels are removed by comparing to the chip mean.
2. Flickering WARM pixels are removed by comparing to the cell mean.
3. In faint areas (zero bgd), flickering pixels are removed with a
cutoff threshold.
Hints:
Choose cell size and thresholds based on the expected background and the PSF.
Use the DIRTYSIS option to examine the anomalous pixel spectra.
Try a multiple pass clean:
Choose a PHA cut to optimize the S/N of the flickering pixels,
then a broad band clean.
Be suspicious of extended source cleans.
For very bright sources you may need to turn off the iteration option.
See the help page for further info (fhelp cleansis)
Poisson clean cell size : 5
Poisson probability threshold : 0.575E-05
Zero Bgd Cutoff threshold (>) : 3
Iterate : F
Dirtysis : F
Minimum PHA value (inclusive) : 0
Maximum PHA value (inclusive) : 4095
open output file: ad55000030s000112h.drk
reading data file: event.tmp
copying primary header to output file...
making chip image...
Total counts in chip images : 852
copy bad pix array...
cleaning chip # 0
Hot pixels & counts : 6 42
Flickering pixels iter, pixels & cnts : 1 64 277
cleaning chip # 1
Hot pixels & counts : 17 114
Flickering pixels iter, pixels & cnts : 1 16 61
cleaning chip # 2
Hot pixels & counts : 7 29
Flickering pixels iter, pixels & cnts : 1 6 18
cleaning chip # 3
Hot pixels & counts : 23 132
Flickering pixels iter, pixels & cnts : 1 9 32
Number of pixels rejected : 148
Number of (internal) image counts : 852
Number of image cts rejected (N, %) : 705 82.7464752
By chip : 0 1 2 3
Pixels rejected : 70 33 13 32
Image counts : 370 226 73 183
Image cts rejected: 319 175 47 164
Image cts rej (%) : 86.22 77.43 64.38 89.62
filtering data...
Total counts : 370 226 73 183
Total cts rejected: 319 175 47 164
Total cts rej (%) : 86.22 77.43 64.38 89.62
Number of clean counts accepted : 147
writing history cards...
copying extensions...
writing out hot pixs...
Number of rejected pixels : 148
updating NEVENTS keywords...
closing data file...
closing clean file...
-> Extracting bright and dark Earth events from ad55000030s000202h.unf
** XSELECT V1.3 **
!> Enter session name >[xsel] earthevents
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS S0CCDPOW
1 GAL_RIDG BRIGHT HIGH 09/04/97 21:02:58 0.11E+05 79486 1111
EXTRACTOR vers 2.0 11 Apr 1997.
Doing file: /data/data16/seq_proc/55000030.005/ad55000030s000202h.unf
Total Good Bad: Region Time Phase Cut
79486 10987 0 68499 0 0
Writing events file
10987 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
79486 10987 0 68499 0 0
in 1639.98 seconds
Command not found; type ? for a command listing
!earthevents:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!earthevents:ASCA > set datadir .
Setting data directory to /data/data16/seq_proc/55000030.005/
Setting mkf directory to /data/data16/seq_proc/55000030.005/
!earthevents:ASCA > read events ad55000030s000202h.unf
Got new instrument: SIS0
Setting: IMAGE binning = 4
WMAP binning = 8
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 2047
Got the minimum time resolution of the read data: 16.000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data16/seq_proc/55000030.005/
HK Directory is: /data/data16/seq_proc/55000030.005/
!earthevents:ASCA-SIS0-BRIGHT > select mkf "FOV==1" data_dir=. ASCA_mkf_def_expr=ft*.mkf
!earthevents:ASCA-SIS0-BRIGHT > extract events
!earthevents:ASCA-SIS0-BRIGHT > save events outfile=event.tmp use_events=no
Wrote events list to file event.tmp
!earthevents:ASCA-SIS0-BRIGHT > exit save_session=no
-> Cleaning hot pixels from ad55000030s000202h.unf
CLEANSIS_V1.6
allocating image arrays...
PROGRAM TO MAKE AN SIS SCIENCE FILE CLEANED OF ANOMALOUS PIXELS.
* Anomalous pixels may consist of at least two populations.
1. Persistent HOT pixels are removed by comparing to the chip mean.
2. Flickering WARM pixels are removed by comparing to the cell mean.
3. In faint areas (zero bgd), flickering pixels are removed with a
cutoff threshold.
Hints:
Choose cell size and thresholds based on the expected background and the PSF.
Use the DIRTYSIS option to examine the anomalous pixel spectra.
Try a multiple pass clean:
Choose a PHA cut to optimize the S/N of the flickering pixels,
then a broad band clean.
Be suspicious of extended source cleans.
For very bright sources you may need to turn off the iteration option.
See the help page for further info (fhelp cleansis)
Poisson clean cell size : 5
Poisson probability threshold : 0.575E-05
Zero Bgd Cutoff threshold (>) : 3
Iterate : F
Dirtysis : F
Minimum PHA value (inclusive) : 0
Maximum PHA value (inclusive) : 4095
open output file: ad55000030s000202h.drk
reading data file: event.tmp
copying primary header to output file...
making chip image...
Total counts in chip images : 10987
copy bad pix array...
cleaning chip # 0
Hot pixels & counts : 56 4570
Flickering pixels iter, pixels & cnts : 1 24 269
cleaning chip # 1
Hot pixels & counts : 29 2139
Flickering pixels iter, pixels & cnts : 1 14 83
cleaning chip # 2
Hot pixels & counts : 25 1954
Flickering pixels iter, pixels & cnts : 1 4 19
cleaning chip # 3
Hot pixels & counts : 26 1758
Flickering pixels iter, pixels & cnts : 1 10 69
Number of pixels rejected : 188
Number of (internal) image counts : 10987
Number of image cts rejected (N, %) : 10861 98.8531876
By chip : 0 1 2 3
Pixels rejected : 80 43 29 36
Image counts : 4872 2266 1999 1850
Image cts rejected: 4839 2222 1973 1827
Image cts rej (%) : 99.32 98.06 98.70 98.76
filtering data...
Total counts : 4872 2266 1999 1850
Total cts rejected: 4839 2222 1973 1827
Total cts rej (%) : 99.32 98.06 98.70 98.76
Number of clean counts accepted : 126
writing history cards...
copying extensions...
writing out hot pixs...
Number of rejected pixels : 188
updating NEVENTS keywords...
closing data file...
closing clean file...
-> Extracting bright and dark Earth events from ad55000030s000212h.unf
** XSELECT V1.3 **
!> Enter session name >[xsel] earthevents
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS S0CCDPOW
1 GAL_RIDG BRIGHT2 HIGH 09/04/97 21:02:58 0.11E+05 91162 1111
EXTRACTOR vers 2.0 11 Apr 1997.
Doing file: /data/data16/seq_proc/55000030.005/ad55000030s000212h.unf
Total Good Bad: Region Time Phase Cut
91162 12292 0 78870 0 0
Writing events file
12292 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
91162 12292 0 78870 0 0
in 1639.98 seconds
Command not found; type ? for a command listing
!earthevents:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!earthevents:ASCA > set datadir .
Setting data directory to /data/data16/seq_proc/55000030.005/
Setting mkf directory to /data/data16/seq_proc/55000030.005/
!earthevents:ASCA > read events ad55000030s000212h.unf
Got new instrument: SIS0
Setting: IMAGE binning = 4
WMAP binning = 8
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 4095
Got the minimum time resolution of the read data: 16.000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data16/seq_proc/55000030.005/
HK Directory is: /data/data16/seq_proc/55000030.005/
!earthevents:ASCA-SIS0-BRIGHT2 > select mkf "FOV==1" data_dir=. ASCA_mkf_def_expr=ft*.mkf
!earthevents:ASCA-SIS0-BRIGHT2 > extract events
!earthevents:ASCA-SIS0-BRIGHT2 > save events outfile=event.tmp use_events=no
Wrote events list to file event.tmp
!earthevents:ASCA-SIS0-BRIGHT2 > exit save_session=no
-> Cleaning hot pixels from ad55000030s000212h.unf
CLEANSIS_V1.6
allocating image arrays...
PROGRAM TO MAKE AN SIS SCIENCE FILE CLEANED OF ANOMALOUS PIXELS.
* Anomalous pixels may consist of at least two populations.
1. Persistent HOT pixels are removed by comparing to the chip mean.
2. Flickering WARM pixels are removed by comparing to the cell mean.
3. In faint areas (zero bgd), flickering pixels are removed with a
cutoff threshold.
Hints:
Choose cell size and thresholds based on the expected background and the PSF.
Use the DIRTYSIS option to examine the anomalous pixel spectra.
Try a multiple pass clean:
Choose a PHA cut to optimize the S/N of the flickering pixels,
then a broad band clean.
Be suspicious of extended source cleans.
For very bright sources you may need to turn off the iteration option.
See the help page for further info (fhelp cleansis)
Poisson clean cell size : 5
Poisson probability threshold : 0.575E-05
Zero Bgd Cutoff threshold (>) : 3
Iterate : F
Dirtysis : F
Minimum PHA value (inclusive) : 0
Maximum PHA value (inclusive) : 4095
open output file: ad55000030s000212h.drk
reading data file: event.tmp
copying primary header to output file...
making chip image...
Total counts in chip images : 12292
copy bad pix array...
cleaning chip # 0
Hot pixels & counts : 60 5193
Flickering pixels iter, pixels & cnts : 1 21 266
cleaning chip # 1
Hot pixels & counts : 31 2364
Flickering pixels iter, pixels & cnts : 1 16 91
cleaning chip # 2
Hot pixels & counts : 26 2166
Flickering pixels iter, pixels & cnts : 1 5 35
cleaning chip # 3
Hot pixels & counts : 28 1922
Flickering pixels iter, pixels & cnts : 1 10 72
Number of pixels rejected : 197
Number of (internal) image counts : 12292
Number of image cts rejected (N, %) : 12109 98.5112305
By chip : 0 1 2 3
Pixels rejected : 81 47 31 38
Image counts : 5512 2523 2231 2026
Image cts rejected: 5459 2455 2201 1994
Image cts rej (%) : 99.04 97.30 98.66 98.42
filtering data...
Total counts : 5512 2523 2231 2026
Total cts rejected: 5459 2455 2201 1994
Total cts rej (%) : 99.04 97.30 98.66 98.42
Number of clean counts accepted : 183
writing history cards...
copying extensions...
writing out hot pixs...
Number of rejected pixels : 197
updating NEVENTS keywords...
closing data file...
closing clean file...
-> Extracting bright and dark Earth events from ad55000030s000302m.unf
** XSELECT V1.3 **
!> Enter session name >[xsel] earthevents
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS S0CCDPOW
1 GAL_RIDG BRIGHT MEDIUM 09/04/97 20:51:26 0.24E+04 16157 1111
EXTRACTOR vers 2.0 11 Apr 1997.
Doing file: /data/data16/seq_proc/55000030.005/ad55000030s000302m.unf
Total Good Bad: Region Time Phase Cut
16157 6200 0 9957 0 0
Writing events file
6200 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
16157 6200 0 9957 0 0
in 832.04 seconds
Command not found; type ? for a command listing
!earthevents:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!earthevents:ASCA > set datadir .
Setting data directory to /data/data16/seq_proc/55000030.005/
Setting mkf directory to /data/data16/seq_proc/55000030.005/
!earthevents:ASCA > read events ad55000030s000302m.unf
Got new instrument: SIS0
Setting: IMAGE binning = 4
WMAP binning = 8
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 2047
Got the minimum time resolution of the read data: 16.000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data16/seq_proc/55000030.005/
HK Directory is: /data/data16/seq_proc/55000030.005/
!earthevents:ASCA-SIS0-BRIGHT > select mkf "FOV==1" data_dir=. ASCA_mkf_def_expr=ft*.mkf
!earthevents:ASCA-SIS0-BRIGHT > extract events
!earthevents:ASCA-SIS0-BRIGHT > save events outfile=event.tmp use_events=no
Wrote events list to file event.tmp
!earthevents:ASCA-SIS0-BRIGHT > exit save_session=no
-> Cleaning hot pixels from ad55000030s000302m.unf
CLEANSIS_V1.6
allocating image arrays...
PROGRAM TO MAKE AN SIS SCIENCE FILE CLEANED OF ANOMALOUS PIXELS.
* Anomalous pixels may consist of at least two populations.
1. Persistent HOT pixels are removed by comparing to the chip mean.
2. Flickering WARM pixels are removed by comparing to the cell mean.
3. In faint areas (zero bgd), flickering pixels are removed with a
cutoff threshold.
Hints:
Choose cell size and thresholds based on the expected background and the PSF.
Use the DIRTYSIS option to examine the anomalous pixel spectra.
Try a multiple pass clean:
Choose a PHA cut to optimize the S/N of the flickering pixels,
then a broad band clean.
Be suspicious of extended source cleans.
For very bright sources you may need to turn off the iteration option.
See the help page for further info (fhelp cleansis)
Poisson clean cell size : 5
Poisson probability threshold : 0.575E-05
Zero Bgd Cutoff threshold (>) : 3
Iterate : F
Dirtysis : F
Minimum PHA value (inclusive) : 0
Maximum PHA value (inclusive) : 4095
open output file: ad55000030s000302m.drk
reading data file: event.tmp
copying primary header to output file...
making chip image...
Total counts in chip images : 6200
copy bad pix array...
cleaning chip # 0
Hot pixels & counts : 56 2200
Flickering pixels iter, pixels & cnts : 1 22 172
cleaning chip # 1
Hot pixels & counts : 31 1341
Flickering pixels iter, pixels & cnts : 1 15 89
cleaning chip # 2
Hot pixels & counts : 25 988
Flickering pixels iter, pixels & cnts : 1 4 23
cleaning chip # 3
Hot pixels & counts : 31 1163
Flickering pixels iter, pixels & cnts : 1 7 41
Number of pixels rejected : 191
Number of (internal) image counts : 6200
Number of image cts rejected (N, %) : 6017 97.0483856
By chip : 0 1 2 3
Pixels rejected : 78 46 29 38
Image counts : 2453 1472 1033 1242
Image cts rejected: 2372 1430 1011 1204
Image cts rej (%) : 96.70 97.15 97.87 96.94
filtering data...
Total counts : 2453 1472 1033 1242
Total cts rejected: 2372 1430 1011 1204
Total cts rej (%) : 96.70 97.15 97.87 96.94
Number of clean counts accepted : 183
writing history cards...
copying extensions...
writing out hot pixs...
Number of rejected pixels : 191
updating NEVENTS keywords...
closing data file...
closing clean file...
-> Extracting bright and dark Earth events from ad55000030s100102h.unf
** XSELECT V1.3 **
!> Enter session name >[xsel] earthevents
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS S1CCDPOW
1 GAL_RIDG BRIGHT HIGH 09/04/97 21:02:58 0.17E+05 148330 1111
EXTRACTOR vers 2.0 11 Apr 1997.
Doing file: /data/data16/seq_proc/55000030.005/ad55000030s100102h.unf
Total Good Bad: Region Time Phase Cut
148330 17304 0 131026 0 0
Writing events file
17304 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
148330 17304 0 131026 0 0
in 1393.78 seconds
Command not found; type ? for a command listing
!earthevents:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!earthevents:ASCA > set datadir .
Setting data directory to /data/data16/seq_proc/55000030.005/
Setting mkf directory to /data/data16/seq_proc/55000030.005/
!earthevents:ASCA > read events ad55000030s100102h.unf
Got new instrument: SIS1
Setting: IMAGE binning = 4
WMAP binning = 8
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 2047
Got the minimum time resolution of the read data: 16.000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data16/seq_proc/55000030.005/
HK Directory is: /data/data16/seq_proc/55000030.005/
!earthevents:ASCA-SIS1-BRIGHT > select mkf "FOV==1" data_dir=. ASCA_mkf_def_expr=ft*.mkf
!earthevents:ASCA-SIS1-BRIGHT > extract events
!earthevents:ASCA-SIS1-BRIGHT > save events outfile=event.tmp use_events=no
Wrote events list to file event.tmp
!earthevents:ASCA-SIS1-BRIGHT > exit save_session=no
-> Cleaning hot pixels from ad55000030s100102h.unf
CLEANSIS_V1.6
allocating image arrays...
PROGRAM TO MAKE AN SIS SCIENCE FILE CLEANED OF ANOMALOUS PIXELS.
* Anomalous pixels may consist of at least two populations.
1. Persistent HOT pixels are removed by comparing to the chip mean.
2. Flickering WARM pixels are removed by comparing to the cell mean.
3. In faint areas (zero bgd), flickering pixels are removed with a
cutoff threshold.
Hints:
Choose cell size and thresholds based on the expected background and the PSF.
Use the DIRTYSIS option to examine the anomalous pixel spectra.
Try a multiple pass clean:
Choose a PHA cut to optimize the S/N of the flickering pixels,
then a broad band clean.
Be suspicious of extended source cleans.
For very bright sources you may need to turn off the iteration option.
See the help page for further info (fhelp cleansis)
Poisson clean cell size : 5
Poisson probability threshold : 0.575E-05
Zero Bgd Cutoff threshold (>) : 3
Iterate : F
Dirtysis : F
Minimum PHA value (inclusive) : 0
Maximum PHA value (inclusive) : 4095
open output file: ad55000030s100102h.drk
reading data file: event.tmp
copying primary header to output file...
making chip image...
Total counts in chip images : 17304
copy bad pix array...
cleaning chip # 0
Hot pixels & counts : 64 4135
Flickering pixels iter, pixels & cnts : 1 28 303
cleaning chip # 1
Hot pixels & counts : 68 4910
Flickering pixels iter, pixels & cnts : 1 24 252
cleaning chip # 2
Hot pixels & counts : 61 4150
Flickering pixels iter, pixels & cnts : 1 25 266
cleaning chip # 3
Hot pixels & counts : 52 2915
Flickering pixels iter, pixels & cnts : 1 22 234
Number of pixels rejected : 344
Number of (internal) image counts : 17304
Number of image cts rejected (N, %) : 17165 99.1967163
By chip : 0 1 2 3
Pixels rejected : 92 92 86 74
Image counts : 4464 5212 4456 3172
Image cts rejected: 4438 5162 4416 3149
Image cts rej (%) : 99.42 99.04 99.10 99.27
filtering data...
Total counts : 4464 5212 4456 3172
Total cts rejected: 4438 5162 4416 3149
Total cts rej (%) : 99.42 99.04 99.10 99.27
Number of clean counts accepted : 139
writing history cards...
copying extensions...
writing out hot pixs...
Number of rejected pixels : 344
updating NEVENTS keywords...
closing data file...
closing clean file...
-> Extracting bright and dark Earth events from ad55000030s100112h.unf
** XSELECT V1.3 **
!> Enter session name >[xsel] earthevents
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS S1CCDPOW
1 GAL_RIDG BRIGHT2 HIGH 09/04/97 21:02:58 0.17E+05 202435 1111
EXTRACTOR vers 2.0 11 Apr 1997.
Doing file: /data/data16/seq_proc/55000030.005/ad55000030s100112h.unf
Total Good Bad: Region Time Phase Cut
202435 22306 0 180129 0 0
Writing events file
22306 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
202435 22306 0 180129 0 0
in 1393.78 seconds
Command not found; type ? for a command listing
!earthevents:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!earthevents:ASCA > set datadir .
Setting data directory to /data/data16/seq_proc/55000030.005/
Setting mkf directory to /data/data16/seq_proc/55000030.005/
!earthevents:ASCA > read events ad55000030s100112h.unf
Got new instrument: SIS1
Setting: IMAGE binning = 4
WMAP binning = 8
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 4095
Got the minimum time resolution of the read data: 16.000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data16/seq_proc/55000030.005/
HK Directory is: /data/data16/seq_proc/55000030.005/
!earthevents:ASCA-SIS1-BRIGHT2 > select mkf "FOV==1" data_dir=. ASCA_mkf_def_expr=ft*.mkf
!earthevents:ASCA-SIS1-BRIGHT2 > extract events
!earthevents:ASCA-SIS1-BRIGHT2 > save events outfile=event.tmp use_events=no
Wrote events list to file event.tmp
!earthevents:ASCA-SIS1-BRIGHT2 > exit save_session=no
-> Cleaning hot pixels from ad55000030s100112h.unf
CLEANSIS_V1.6
allocating image arrays...
PROGRAM TO MAKE AN SIS SCIENCE FILE CLEANED OF ANOMALOUS PIXELS.
* Anomalous pixels may consist of at least two populations.
1. Persistent HOT pixels are removed by comparing to the chip mean.
2. Flickering WARM pixels are removed by comparing to the cell mean.
3. In faint areas (zero bgd), flickering pixels are removed with a
cutoff threshold.
Hints:
Choose cell size and thresholds based on the expected background and the PSF.
Use the DIRTYSIS option to examine the anomalous pixel spectra.
Try a multiple pass clean:
Choose a PHA cut to optimize the S/N of the flickering pixels,
then a broad band clean.
Be suspicious of extended source cleans.
For very bright sources you may need to turn off the iteration option.
See the help page for further info (fhelp cleansis)
Poisson clean cell size : 5
Poisson probability threshold : 0.575E-05
Zero Bgd Cutoff threshold (>) : 3
Iterate : F
Dirtysis : F
Minimum PHA value (inclusive) : 0
Maximum PHA value (inclusive) : 4095
open output file: ad55000030s100112h.drk
reading data file: event.tmp
copying primary header to output file...
making chip image...
Total counts in chip images : 22306
copy bad pix array...
cleaning chip # 0
Hot pixels & counts : 79 5857
Flickering pixels iter, pixels & cnts : 1 24 269
cleaning chip # 1
Hot pixels & counts : 73 5646
Flickering pixels iter, pixels & cnts : 1 24 324
cleaning chip # 2
Hot pixels & counts : 69 5131
Flickering pixels iter, pixels & cnts : 1 20 233
cleaning chip # 3
Hot pixels & counts : 62 4470
Flickering pixels iter, pixels & cnts : 1 16 196
Number of pixels rejected : 367
Number of (internal) image counts : 22306
Number of image cts rejected (N, %) : 22126 99.1930389
By chip : 0 1 2 3
Pixels rejected : 103 97 89 78
Image counts : 6160 6032 5410 4704
Image cts rejected: 6126 5970 5364 4666
Image cts rej (%) : 99.45 98.97 99.15 99.19
filtering data...
Total counts : 6160 6032 5410 4704
Total cts rejected: 6126 5970 5364 4666
Total cts rej (%) : 99.45 98.97 99.15 99.19
Number of clean counts accepted : 180
writing history cards...
copying extensions...
writing out hot pixs...
Number of rejected pixels : 367
updating NEVENTS keywords...
closing data file...
closing clean file...
-> Extracting bright and dark Earth events from ad55000030s100202h.unf
** XSELECT V1.3 **
!> Enter session name >[xsel] earthevents
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS S1CCDPOW
1 GAL_RIDG BRIGHT HIGH 10/04/97 02:43:42 0.19E+04 5902 1111
EXTRACTOR vers 2.0 11 Apr 1997.
Doing file: /data/data16/seq_proc/55000030.005/ad55000030s100202h.unf
Total Good Bad: Region Time Phase Cut
5902 4116 0 1786 0 0
Writing events file
4116 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
5902 4116 0 1786 0 0
in 397.90 seconds
Command not found; type ? for a command listing
!earthevents:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!earthevents:ASCA > set datadir .
Setting data directory to /data/data16/seq_proc/55000030.005/
Setting mkf directory to /data/data16/seq_proc/55000030.005/
!earthevents:ASCA > read events ad55000030s100202h.unf
Got new instrument: SIS1
Setting: IMAGE binning = 4
WMAP binning = 8
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 2047
Got the minimum time resolution of the read data: 16.000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data16/seq_proc/55000030.005/
HK Directory is: /data/data16/seq_proc/55000030.005/
!earthevents:ASCA-SIS1-BRIGHT > select mkf "FOV==1" data_dir=. ASCA_mkf_def_expr=ft*.mkf
!earthevents:ASCA-SIS1-BRIGHT > extract events
!earthevents:ASCA-SIS1-BRIGHT > save events outfile=event.tmp use_events=no
Wrote events list to file event.tmp
!earthevents:ASCA-SIS1-BRIGHT > exit save_session=no
-> Cleaning hot pixels from ad55000030s100202h.unf
CLEANSIS_V1.6
allocating image arrays...
PROGRAM TO MAKE AN SIS SCIENCE FILE CLEANED OF ANOMALOUS PIXELS.
* Anomalous pixels may consist of at least two populations.
1. Persistent HOT pixels are removed by comparing to the chip mean.
2. Flickering WARM pixels are removed by comparing to the cell mean.
3. In faint areas (zero bgd), flickering pixels are removed with a
cutoff threshold.
Hints:
Choose cell size and thresholds based on the expected background and the PSF.
Use the DIRTYSIS option to examine the anomalous pixel spectra.
Try a multiple pass clean:
Choose a PHA cut to optimize the S/N of the flickering pixels,
then a broad band clean.
Be suspicious of extended source cleans.
For very bright sources you may need to turn off the iteration option.
See the help page for further info (fhelp cleansis)
Poisson clean cell size : 5
Poisson probability threshold : 0.575E-05
Zero Bgd Cutoff threshold (>) : 3
Iterate : F
Dirtysis : F
Minimum PHA value (inclusive) : 0
Maximum PHA value (inclusive) : 4095
open output file: ad55000030s100202h.drk
reading data file: event.tmp
copying primary header to output file...
making chip image...
Total counts in chip images : 4116
copy bad pix array...
cleaning chip # 0
Hot pixels & counts : 45 898
Flickering pixels iter, pixels & cnts : 1 22 146
cleaning chip # 1
Hot pixels & counts : 55 1088
Flickering pixels iter, pixels & cnts : 1 20 107
cleaning chip # 2
Hot pixels & counts : 48 975
Flickering pixels iter, pixels & cnts : 1 14 75
cleaning chip # 3
Hot pixels & counts : 39 645
Flickering pixels iter, pixels & cnts : 1 19 106
Number of pixels rejected : 262
Number of (internal) image counts : 4116
Number of image cts rejected (N, %) : 4040 98.1535492
By chip : 0 1 2 3
Pixels rejected : 67 75 62 58
Image counts : 1062 1214 1074 766
Image cts rejected: 1044 1195 1050 751
Image cts rej (%) : 98.31 98.43 97.77 98.04
filtering data...
Total counts : 1062 1214 1074 766
Total cts rejected: 1044 1195 1050 751
Total cts rej (%) : 98.31 98.43 97.77 98.04
Number of clean counts accepted : 76
writing history cards...
copying extensions...
writing out hot pixs...
Number of rejected pixels : 262
updating NEVENTS keywords...
closing data file...
closing clean file...
-> Extracting bright and dark Earth events from ad55000030s100212h.unf
** XSELECT V1.3 **
!> Enter session name >[xsel] earthevents
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS S1CCDPOW
1 GAL_RIDG BRIGHT2 HIGH 10/04/97 02:43:42 0.19E+04 8860 1111
EXTRACTOR vers 2.0 11 Apr 1997.
Doing file: /data/data16/seq_proc/55000030.005/ad55000030s100212h.unf
Total Good Bad: Region Time Phase Cut
8860 5569 0 3291 0 0
Writing events file
5569 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
8860 5569 0 3291 0 0
in 397.90 seconds
Command not found; type ? for a command listing
!earthevents:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!earthevents:ASCA > set datadir .
Setting data directory to /data/data16/seq_proc/55000030.005/
Setting mkf directory to /data/data16/seq_proc/55000030.005/
!earthevents:ASCA > read events ad55000030s100212h.unf
Got new instrument: SIS1
Setting: IMAGE binning = 4
WMAP binning = 8
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 4095
Got the minimum time resolution of the read data: 16.000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data16/seq_proc/55000030.005/
HK Directory is: /data/data16/seq_proc/55000030.005/
!earthevents:ASCA-SIS1-BRIGHT2 > select mkf "FOV==1" data_dir=. ASCA_mkf_def_expr=ft*.mkf
!earthevents:ASCA-SIS1-BRIGHT2 > extract events
!earthevents:ASCA-SIS1-BRIGHT2 > save events outfile=event.tmp use_events=no
Wrote events list to file event.tmp
!earthevents:ASCA-SIS1-BRIGHT2 > exit save_session=no
-> Cleaning hot pixels from ad55000030s100212h.unf
CLEANSIS_V1.6
allocating image arrays...
PROGRAM TO MAKE AN SIS SCIENCE FILE CLEANED OF ANOMALOUS PIXELS.
* Anomalous pixels may consist of at least two populations.
1. Persistent HOT pixels are removed by comparing to the chip mean.
2. Flickering WARM pixels are removed by comparing to the cell mean.
3. In faint areas (zero bgd), flickering pixels are removed with a
cutoff threshold.
Hints:
Choose cell size and thresholds based on the expected background and the PSF.
Use the DIRTYSIS option to examine the anomalous pixel spectra.
Try a multiple pass clean:
Choose a PHA cut to optimize the S/N of the flickering pixels,
then a broad band clean.
Be suspicious of extended source cleans.
For very bright sources you may need to turn off the iteration option.
See the help page for further info (fhelp cleansis)
Poisson clean cell size : 5
Poisson probability threshold : 0.575E-05
Zero Bgd Cutoff threshold (>) : 3
Iterate : F
Dirtysis : F
Minimum PHA value (inclusive) : 0
Maximum PHA value (inclusive) : 4095
open output file: ad55000030s100212h.drk
reading data file: event.tmp
copying primary header to output file...
making chip image...
Total counts in chip images : 5569
copy bad pix array...
cleaning chip # 0
Hot pixels & counts : 64 1356
Flickering pixels iter, pixels & cnts : 1 22 148
cleaning chip # 1
Hot pixels & counts : 63 1303
Flickering pixels iter, pixels & cnts : 1 18 102
cleaning chip # 2
Hot pixels & counts : 56 1270
Flickering pixels iter, pixels & cnts : 1 20 123
cleaning chip # 3
Hot pixels & counts : 55 1117
Flickering pixels iter, pixels & cnts : 1 14 75
Number of pixels rejected : 312
Number of (internal) image counts : 5569
Number of image cts rejected (N, %) : 5494 98.6532593
By chip : 0 1 2 3
Pixels rejected : 86 81 76 69
Image counts : 1514 1432 1416 1207
Image cts rejected: 1504 1405 1393 1192
Image cts rej (%) : 99.34 98.11 98.38 98.76
filtering data...
Total counts : 1514 1432 1416 1207
Total cts rejected: 1504 1405 1393 1192
Total cts rej (%) : 99.34 98.11 98.38 98.76
Number of clean counts accepted : 75
writing history cards...
copying extensions...
writing out hot pixs...
Number of rejected pixels : 312
updating NEVENTS keywords...
closing data file...
closing clean file...
-> Extracting bright and dark Earth events from ad55000030s100302m.unf
** XSELECT V1.3 **
!> Enter session name >[xsel] earthevents
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS S1CCDPOW
1 GAL_RIDG BRIGHT MEDIUM 09/04/97 20:51:26 0.24E+04 18867 1111
EXTRACTOR vers 2.0 11 Apr 1997.
Doing file: /data/data16/seq_proc/55000030.005/ad55000030s100302m.unf
Total Good Bad: Region Time Phase Cut
18867 7375 0 11492 0 0
Writing events file
7375 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
18867 7375 0 11492 0 0
in 832.04 seconds
Command not found; type ? for a command listing
!earthevents:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!earthevents:ASCA > set datadir .
Setting data directory to /data/data16/seq_proc/55000030.005/
Setting mkf directory to /data/data16/seq_proc/55000030.005/
!earthevents:ASCA > read events ad55000030s100302m.unf
Got new instrument: SIS1
Setting: IMAGE binning = 4
WMAP binning = 8
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 2047
Got the minimum time resolution of the read data: 16.000
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data16/seq_proc/55000030.005/
HK Directory is: /data/data16/seq_proc/55000030.005/
!earthevents:ASCA-SIS1-BRIGHT > select mkf "FOV==1" data_dir=. ASCA_mkf_def_expr=ft*.mkf
!earthevents:ASCA-SIS1-BRIGHT > extract events
!earthevents:ASCA-SIS1-BRIGHT > save events outfile=event.tmp use_events=no
Wrote events list to file event.tmp
!earthevents:ASCA-SIS1-BRIGHT > exit save_session=no
-> Cleaning hot pixels from ad55000030s100302m.unf
CLEANSIS_V1.6
allocating image arrays...
PROGRAM TO MAKE AN SIS SCIENCE FILE CLEANED OF ANOMALOUS PIXELS.
* Anomalous pixels may consist of at least two populations.
1. Persistent HOT pixels are removed by comparing to the chip mean.
2. Flickering WARM pixels are removed by comparing to the cell mean.
3. In faint areas (zero bgd), flickering pixels are removed with a
cutoff threshold.
Hints:
Choose cell size and thresholds based on the expected background and the PSF.
Use the DIRTYSIS option to examine the anomalous pixel spectra.
Try a multiple pass clean:
Choose a PHA cut to optimize the S/N of the flickering pixels,
then a broad band clean.
Be suspicious of extended source cleans.
For very bright sources you may need to turn off the iteration option.
See the help page for further info (fhelp cleansis)
Poisson clean cell size : 5
Poisson probability threshold : 0.575E-05
Zero Bgd Cutoff threshold (>) : 3
Iterate : F
Dirtysis : F
Minimum PHA value (inclusive) : 0
Maximum PHA value (inclusive) : 4095
open output file: ad55000030s100302m.drk
reading data file: event.tmp
copying primary header to output file...
making chip image...
Total counts in chip images : 7375
copy bad pix array...
cleaning chip # 0
Hot pixels & counts : 45 1644
Flickering pixels iter, pixels & cnts : 1 25 165
cleaning chip # 1
Hot pixels & counts : 48 1665
Flickering pixels iter, pixels & cnts : 1 21 111
cleaning chip # 2
Hot pixels & counts : 49 1745
Flickering pixels iter, pixels & cnts : 1 30 212
cleaning chip # 3
Hot pixels & counts : 43 1581
Flickering pixels iter, pixels & cnts : 1 19 125
Number of pixels rejected : 280
Number of (internal) image counts : 7375
Number of image cts rejected (N, %) : 7248 98.2779694
By chip : 0 1 2 3
Pixels rejected : 70 69 79 62
Image counts : 1836 1808 1991 1740
Image cts rejected: 1809 1776 1957 1706
Image cts rej (%) : 98.53 98.23 98.29 98.05
filtering data...
Total counts : 1836 1808 1991 1740
Total cts rejected: 1809 1776 1957 1706
Total cts rej (%) : 98.53 98.23 98.29 98.05
Number of clean counts accepted : 127
writing history cards...
copying extensions...
writing out hot pixs...
Number of rejected pixels : 280
updating NEVENTS keywords...
closing data file...
closing clean file...
-> Extracting bright and dark Earth events from ad55000030g200170h.unf
** XSELECT V1.3 **
!> Enter session name >[xsel] earthevents
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS PHA_BINS
1 GAL_RIDG PH HIGH 09/04/97 21:03:10 0.19E+05 19577 1024
EXTRACTOR vers 2.0 11 Apr 1997.
Doing file: /data/data16/seq_proc/55000030.005/ad55000030g200170h.unf
Total Good Bad: Region Time Phase Cut
19577 1761 0 17816 0 0
Writing events file
1761 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
19577 1761 0 17816 0 0
in 3091.96 seconds
Command not found; type ? for a command listing
!earthevents:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!earthevents:ASCA > set datadir .
Setting data directory to /data/data16/seq_proc/55000030.005/
Setting mkf directory to /data/data16/seq_proc/55000030.005/
!earthevents:ASCA > read events ad55000030g200170h.unf
Got new instrument: GIS2
Setting: IMAGE binning = 1
WMAP binning = 1
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 1023
Got the minimum time resolution of the read data: 0.62500E-01
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data16/seq_proc/55000030.005/
HK Directory is: /data/data16/seq_proc/55000030.005/
!earthevents:ASCA-GIS2-PH > select mkf "FOV==1" data_dir=. ASCA_mkf_def_expr=ft*.mkf
!earthevents:ASCA-GIS2-PH > extract events
!earthevents:ASCA-GIS2-PH > save events outfile=event.tmp use_events=no
Wrote events list to file event.tmp
!earthevents:ASCA-GIS2-PH > exit save_session=no
-> Extracting ad55000030g200170h.brt
** XSELECT V1.3 **
!> Enter session name >[xsel] earthevents
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS PHA_BINS
1 GAL_RIDG PH HIGH 09/04/97 21:03:10 0.19E+05 19577 1024
EXTRACTOR vers 2.0 11 Apr 1997.
Doing file: /data/data16/seq_proc/55000030.005/ad55000030g200170h.unf
Total Good Bad: Region Time Phase Cut
19577 4862 0 14715 0 0
Writing events file
4862 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
19577 4862 0 14715 0 0
in 5489.94 seconds
Command not found; type ? for a command listing
!earthevents:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!earthevents:ASCA > set datadir .
Setting data directory to /data/data16/seq_proc/55000030.005/
Setting mkf directory to /data/data16/seq_proc/55000030.005/
!earthevents:ASCA > read events ad55000030g200170h.unf
Got new instrument: GIS2
Setting: IMAGE binning = 1
WMAP binning = 1
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 1023
Got the minimum time resolution of the read data: 0.62500E-01
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data16/seq_proc/55000030.005/
HK Directory is: /data/data16/seq_proc/55000030.005/
!earthevents:ASCA-GIS2-PH > select mkf "FOV==2" data_dir=. ASCA_mkf_def_expr=ft*.mkf
!earthevents:ASCA-GIS2-PH > extract events
!earthevents:ASCA-GIS2-PH > save events outfile=event.tmp use_events=no
Wrote events list to file event.tmp
!earthevents:ASCA-GIS2-PH > exit save_session=no
-> Extracting bright and dark Earth events from ad55000030g300170h.unf
** XSELECT V1.3 **
!> Enter session name >[xsel] earthevents
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS PHA_BINS
1 GAL_RIDG PH HIGH 09/04/97 21:03:10 0.19E+05 18594 1024
EXTRACTOR vers 2.0 11 Apr 1997.
Doing file: /data/data16/seq_proc/55000030.005/ad55000030g300170h.unf
Total Good Bad: Region Time Phase Cut
18594 1556 0 17038 0 0
Writing events file
1556 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
18594 1556 0 17038 0 0
in 3091.96 seconds
Command not found; type ? for a command listing
!earthevents:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!earthevents:ASCA > set datadir .
Setting data directory to /data/data16/seq_proc/55000030.005/
Setting mkf directory to /data/data16/seq_proc/55000030.005/
!earthevents:ASCA > read events ad55000030g300170h.unf
Got new instrument: GIS3
Setting: IMAGE binning = 1
WMAP binning = 1
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 1023
Got the minimum time resolution of the read data: 0.62500E-01
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data16/seq_proc/55000030.005/
HK Directory is: /data/data16/seq_proc/55000030.005/
!earthevents:ASCA-GIS3-PH > select mkf "FOV==1" data_dir=. ASCA_mkf_def_expr=ft*.mkf
!earthevents:ASCA-GIS3-PH > extract events
!earthevents:ASCA-GIS3-PH > save events outfile=event.tmp use_events=no
Wrote events list to file event.tmp
!earthevents:ASCA-GIS3-PH > exit save_session=no
-> Extracting ad55000030g300170h.brt
** XSELECT V1.3 **
!> Enter session name >[xsel] earthevents
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
OBJECT DATAMODE BIT_RATE DATE-OBS TIME-OBS ONTIME NEVENTS PHA_BINS
1 GAL_RIDG PH HIGH 09/04/97 21:03:10 0.19E+05 18594 1024
EXTRACTOR vers 2.0 11 Apr 1997.
Doing file: /data/data16/seq_proc/55000030.005/ad55000030g300170h.unf
Total Good Bad: Region Time Phase Cut
18594 4724 0 13870 0 0
Writing events file
4724 events written to the output file
===============================================================================
Grand Total Good Bad: Region Time Phase Cut
18594 4724 0 13870 0 0
in 5489.94 seconds
Command not found; type ? for a command listing
!earthevents:ASCA > set mission ASCA
Notes: XSELECT set up for ASCA
Keywords for time and pha are TIME PI
Units of time are s
Default timing binsize = 16.00
Keywords for images are DETX DETY
Keywords for the WMAP are DETX DETY
!earthevents:ASCA > set datadir .
Setting data directory to /data/data16/seq_proc/55000030.005/
Setting mkf directory to /data/data16/seq_proc/55000030.005/
!earthevents:ASCA > read events ad55000030g300170h.unf
Got new instrument: GIS3
Setting: IMAGE binning = 1
WMAP binning = 1
Energy Column = PI
Energy rebinning = 1
Getting Min and Max for Energy Column...
Got min and max for PI: 0 1023
Got the minimum time resolution of the read data: 0.62500E-01
Number of files read in: 1
******************** Observation Catalogue ********************
Data Directory is: /data/data16/seq_proc/55000030.005/
HK Directory is: /data/data16/seq_proc/55000030.005/
!earthevents:ASCA-GIS3-PH > select mkf "FOV==2" data_dir=. ASCA_mkf_def_expr=ft*.mkf
!earthevents:ASCA-GIS3-PH > extract events
!earthevents:ASCA-GIS3-PH > save events outfile=event.tmp use_events=no
Wrote events list to file event.tmp
!earthevents:ASCA-GIS3-PH > exit save_session=no
Offset of 1.500000000000000E+08 from 1/1/93 0:0:0 is date and time (including leapseconds) = 3/10/97 2:39:56.000000 Modified Julian Day = 50724.111064814816928
ad55000030s000102h.unf|S0_ARENA|1|S0 Area discrimination enable/disable ad55000030s000202h.unf|S0_ARENA|0|S0 Area discrimination enable/disable-> listing ad55000030s000102h.unf
ad55000030s000112h.unf|S0_ARENA|1|S0 Area discrimination enable/disable ad55000030s000212h.unf|S0_ARENA|0|S0 Area discrimination enable/disable-> listing ad55000030s000112h.unf
ad55000030s000101h.unf|S0_ARENA|1|S0 Area discrimination enable/disable ad55000030s000201h.unf|S0_ARENA|0|S0 Area discrimination enable/disable-> listing ad55000030s000101h.unf
ad55000030s100102h.unf|S1_DESTA|0|S1 DE normal/reset ad55000030s100202h.unf|S1_DESTA|1|S1 DE normal/reset-> listing ad55000030s100102h.unf
ad55000030s100112h.unf|S1_DESTA|0|S1 DE normal/reset ad55000030s100212h.unf|S1_DESTA|1|S1 DE normal/reset-> listing ad55000030s100112h.unf
ad55000030s100101h.unf|S1_DESTA|0|S1 DE normal/reset ad55000030s100201h.unf|S1_DESTA|1|S1 DE normal/reset-> listing ad55000030s100101h.unf
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Standard Output From FTOOL fchecksum:
Checksum keywords updated successfully.-> Doing inventory of all files